BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

62 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

BIS, Eastern Regional Laboratory (ERL)

None

IS 2062 (Part 2) (2026)

Structural Steel - Part 2 - Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

For all grades

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-8.1 & 8.4, Table 7 (Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-
Cl-8.1 & 8.4, Table 7 (Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-
Cl-8.1 & 8.4, Table 7 (Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-
Cl-9 & 9.4 (Transverse Charpy V-notch properties a,c S Grades)	-
Cl-10.2.1 (Hot-Forming)	-
Cl-10.2.3 (Flangeability)	-
Cl-10.3 (Hot-Dip Zinc-Coating)	-
Cl-11 (Internal Soundness (Ultrasonic testing))	-
Cl-13 (Freedom From Defect)	-
Cl-14 (Dimensions )	-
Cl-16 (Calculation of Mass )	-

-
Mech: Complete

MATERIAL TESTING LABORATORY LLP

8176306

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

All grade

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	499.95	-
Cl-7(FREEDOM FROM DEFECTS)	-	500	-
Cl-8.1(Ladle Analysis)	-	2500	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	300	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	300	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	500	-
Cl-8.1 & 8.2, Note-5(Nb)	-	300	-
Cl-8.1 & 8.2, Note-5(V)	-	300	-
Cl-8.1 & 8.2, Note-5(Ti)	-	300	-
Cl-8.1 & 8.2, Note-6(B)	-	300	-
Cl-8.2, Table 2 (i)(Carbon)	-	300	-
Cl-8.2, Table 2 (ii)(Manganese)	-	300	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	-
Cl-8.2, Table 2 (v)(Silicon)	-	300	-
Cl-8.2, Table 2 (vi)(Copper)	-	300	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	-
Cl-8.2, Table 2 (viii)(Niobium)	-	300	-
Cl-8.2, Table 2 (ix)(Titanium)	-	300	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	500	-
Cl-10.1(Number of Tensile Tests)	-	1500	-
Cl-10.2(Tensile Test Pieces)	-	1500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	2500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	2500	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	500	-
Cl-12(Impact Test )	-	2500	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	500	-
Cl-14, Table-4 (ii)(Tee bars)	-	500	-
Cl-14, Table-4 (iii)(Bulb angles)	-	500	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	500	-
Cl-14, Table-4 (vi)(Round and square bars)	-	500	-
Cl-14, Table-4 (vii)(Bulb flats)	-	500	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	500	-
Cl-14, Table-4 (ix)(Channel sections)	-	500	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	3000	Optional test
Cl-13.3(Strength of joint )	-	1000	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	0	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-

-
included w.e.f 25.09.2026

Unique Test House LLP

9134536

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

ALL SIZES

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	100	.......................
Cl-7(FREEDOM FROM DEFECTS)	-	100	............................
Cl-8.1(Ladle Analysis)	-	300	.......................
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	300	.....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	300	...................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	...................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	..................................
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	300	......................
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	300	......................
Cl-8.1 & 8.2, Note-5(Nb)	-	300	....................
Cl-8.1 & 8.2, Note-5(V)	-	300	...................
Cl-8.1 & 8.2, Note-5(Ti)	-	300	....................
Cl-8.1 & 8.2, Note-6(B)	-	300	...................
Cl-8.2, Table 2 (i)(Carbon)	-	300	....................
Cl-8.2, Table 2 (ii)(Manganese)	-	300	....................
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	....................
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	.....................
Cl-8.2, Table 2 (v)(Silicon)	-	300	.....................
Cl-8.2, Table 2 (vi)(Copper)	-	300	....................
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	.....................
Cl-8.2, Table 2 (viii)(Niobium)	-	300	....................
Cl-8.2, Table 2 (ix)(Titanium)	-	300	....................
Cl-8.2, Table 2 (x)(Nitrogen)	-	300	....................
Cl-10.1(Number of Tensile Tests)	-	300	....................
Cl-10.2(Tensile Test Pieces)	-	1000	.....................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	300	...................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	300	......................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	300	...................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	300	......................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	300	......................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	300	.....................
Cl-11.1(Number of Bend Tests)	-	300	.....................
Cl-11.2(Bend Test Piece)	-	300	.....................
Cl-11.3(Bend Test )	-	1000	....................
Cl-12(Impact Test )	-	1000	...................
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	300	.....................
Cl-14, Table-4 (ii)(Tee bars)	-	300	....................
Cl-14, Table-4 (iii)(Bulb angles)	-	300	....................
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	300	...................
Cl-14, Table-4 (vi)(Round and square bars)	-	300	....................
Cl-14, Table-4 (vii)(Bulb flats)	-	300	......................
Cl-14, Table-4 (viii)(Sheet piling sections)	-	300	........................
Cl-14, Table-4 (ix)(Channel sections)	-	300	.....................
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	300	...................
Cl-13.3(Strength of joint )	-	300	....................
Cl-15(Tolerances)	-	500	..........................
Cl-16.1(Retests)	-	300	......................
Cl-16.2(Re-heat Treatment)	-	300	.................
Cl-6(MANUFACTURE)	-	100	...........................
Cl-7(FREEDOM FROM DEFECTS)	-	100	........................
Cl-8.1(Ladle Analysis)	-	500	.......................
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	100	....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	300	....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	.....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	....................
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	...................
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	300	...................
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	300	...................................
Cl-8.1 & 8.2, Note-5(Nb)	-	300	....................
Cl-8.1 & 8.2, Note-5(V)	-	300	..................................
Cl-8.1 & 8.2, Note-5(Ti)	-	300	....................
Cl-8.1 & 8.2, Note-6(B)	-	300	..................
Cl-8.2, Table 2 (i)(Carbon)	-	300	..................
Cl-8.2, Table 2 (ii)(Manganese)	-	300	....................
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	...................
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	....................
Cl-8.2, Table 2 (v)(Silicon)	-	300	...................
Cl-8.2, Table 2 (vi)(Copper)	-	300	..................
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	...................
Cl-8.2, Table 2 (viii)(Niobium)	-	300	..................
Cl-8.2, Table 2 (ix)(Titanium)	-	300	...................
Cl-8.2, Table 2 (x)(Nitrogen)	-	300	....................
Cl-10.1(Number of Tensile Tests)	-	1000	..................
Cl-10.2(Tensile Test Pieces)	-	1000	...................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	300	..................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	300	...................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	300	...................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	300	...................................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	300	.............................
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	300	..................
Cl-11.1(Number of Bend Tests)	-	500	..................................
Cl-11.2(Bend Test Piece)	-	500	....................
Cl-11.3(Bend Test )	-	1000	...................
Cl-12(Impact Test )	-	1000	....................
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	300	..................
Cl-14, Table-4 (ii)(Tee bars)	-	300	...................
Cl-14, Table-4 (iii)(Bulb angles)	-	300	...................
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	300	....................
Cl-14, Table-4 (vi)(Round and square bars)	-	300	...................
Cl-14, Table-4 (vii)(Bulb flats)	-	300	..................
Cl-14, Table-4 (viii)(Sheet piling sections)	-	300	....................
Cl-14, Table-4 (ix)(Channel sections)	-	300	.........................
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	300	.................
Cl-13.3(Strength of joint )	-	300	....................
Cl-15(Tolerances)	-	500	....................
Cl-16.1(Retests)	-	300	....................
Cl-16.2(Re-heat Treatment)	-	300	.......................

07 Sep, 2028

-
Included w.e.f 31.08.2026

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

6121636

IS 2062 (Part 2) (2026)

Structural Steel - Part 2 - Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

16800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	0	-
Cl-6(Manufacture )	-	0	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	0	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	0	-
Cl-7.2, Table 3 (i)(Carbon)	-	200	-
Cl-7.2, Table 3 (ii)(Silicon)	-	200	-
Cl-7.2, Table 3 (iii)(Manganese)	-	200	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	200	-
Cl-7.2, Table 3 (v)(Sulphur)	-	200	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	200	-
Cl-7.2, Table 3 (vii)(Niobium)	-	200	-
Cl-7.2, Table 3 (viii)(Boron)	-	200	-
Cl-7.2, Table 3 (ix)(Titanium)	-	200	-
Cl-7.2, Table 3 (x)(Copper)	-	200	-
Cl-7.2, Table 3 (xi)(Nickel)	-	200	-
Cl-7.2, Table 3 (xii)(Chromium)	-	200	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	200	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	200	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	1500	-
Cl-7.2, Table-4 (i)(Carbon)	-	0	-
Cl-7.2, Table-4 (ii)(Silicon)	-	0	-
Cl-7.2, Table-4 (iii)(Manganese)	-	0	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	0	-
Cl-7.2, Table-4 (v)(Sulphur)	-	0	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	0	-
Cl-7.2, Table-4 (vii)(Niobium)	-	0	-
Cl-7.2, Table-4 (viii)(Boron)	-	0	-
Cl-7.2, Table-4 (ix)(Titanium)	-	0	-
Cl-7.2, Table-4 (x)(Copper)	-	0	-
Cl-7.2, Table-4 (xi)(Nickel)	-	0	-
Cl-7.2, Table-4 (xii)(Chromium)	-	0	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	0	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	0	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	0	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	200	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	0	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	0	-
Cl-8.3(Tensile Test Pieces)	-	0	-
Cl-8.4(Tensile Test)	-	2000	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	2500	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	2500	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	1500	-
Cl-10.1(Weldability)	-	1500	-
Cl-10.2.1(Hot-Forming)	-	0	-
Cl-10.2.2(Cold Formability)	-	0	-
Cl-10.2.3(Flangeability)	-	800	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	1000	-
Cl-11(Internal Soundness (Ultrasonic testing))	-	1500	-
Cl-12.1(Re-Tests )	-	0	-
Cl-12.2(Re-Heat Treatment)	-	0	-
Cl-13(Freedom From Defect)	-	200	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	0	-
Cl-16(Calculation of Mass )	-	200	-
Cl-18(Marking and Packing )	-	100	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

6121636

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	50	-
Cl-7(FREEDOM FROM DEFECTS)	-	150	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	200	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	200	-
Cl-8.1 & 8.2, Note-5(Nb)	-	200	-
Cl-8.1 & 8.2, Note-5(V)	-	200	-
Cl-8.1 & 8.2, Note-5(Ti)	-	200	-
Cl-8.1 & 8.2, Note-6(B)	-	200	-
Cl-8.2, Table 2 (i)(Carbon)	-	200	-
Cl-8.2, Table 2 (ii)(Manganese)	-	200	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	200	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	200	-
Cl-8.2, Table 2 (v)(Silicon)	-	200	-
Cl-8.2, Table 2 (vi)(Copper)	-	200	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1500	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	400	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	700	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	2500	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	2500	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	2000	-
Cl-13.3(Strength of joint )	-	700	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	0	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	0	-
Cl-8.1(Ladle Analysis)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	0	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-

19 Apr, 2028

-
Included w.e.f. 18.08.2026

NATIONAL TEST HOUSE-SR (NTH), Chennai

6122704

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

All grades, types and sizes

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	5000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	3000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	5000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.3(Bend Test )	-	1500	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	7000	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-

28 Nov, 2028

-
included w.e.f 04.08.2026

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

9164606

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	1000	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	1000	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	1000	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	1000	-
Cl-8.1 & 8.2, Note-5(Nb)	-	1000	-
Cl-8.1 & 8.2, Note-5(V)	-	1000	-
Cl-8.1 & 8.2, Note-5(Ti)	-	1000	-
Cl-8.1 & 8.2, Note-6(B)	-	1000	-
Cl-8.2, Table 2 (i)(Carbon)	-	1000	-
Cl-8.2, Table 2 (ii)(Manganese)	-	1000	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	1000	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	1000	-
Cl-8.2, Table 2 (v)(Silicon)	-	1000	-
Cl-8.2, Table 2 (vi)(Copper)	-	1000	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	1000	-
Cl-8.2, Table 2 (viii)(Niobium)	-	1000	-
Cl-8.2, Table 2 (ix)(Titanium)	-	1000	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1000	-
Cl-10.1(Number of Tensile Tests)	-	1000	-
Cl-10.2(Tensile Test Pieces)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	1000	-
Cl-11.1(Number of Bend Tests)	-	1000	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	1000	-
Cl-12(Impact Test )	-	1000	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	1000	-
Cl-13.3(Strength of joint )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	1000	-
Cl-16.2(Re-heat Treatment)	-	1000	-
Cl-6(MANUFACTURE)	-	-	-
Cl-7(FREEDOM FROM DEFECTS)	-	-	-
Cl-8.1(Ladle Analysis)	-	-	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	-	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	-	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	-	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	-	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	-	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	-	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	-	-
Cl-8.1 & 8.2, Note-5(Nb)	-	-	-
Cl-8.1 & 8.2, Note-5(V)	-	-	-
Cl-8.1 & 8.2, Note-5(Ti)	-	-	-
Cl-8.1 & 8.2, Note-6(B)	-	-	-
Cl-8.2, Table 2 (i)(Carbon)	-	-	-
Cl-8.2, Table 2 (ii)(Manganese)	-	-	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	-	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	-	-
Cl-8.2, Table 2 (v)(Silicon)	-	-	-
Cl-8.2, Table 2 (vi)(Copper)	-	-	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	-	-
Cl-8.2, Table 2 (viii)(Niobium)	-	-	-
Cl-8.2, Table 2 (ix)(Titanium)	-	-	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	-	-
Cl-10.1(Number of Tensile Tests)	-	-	-
Cl-10.2(Tensile Test Pieces)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	-	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	-	-
Cl-11.1(Number of Bend Tests)	-	-	-
Cl-11.2(Bend Test Piece)	-	-	-
Cl-11.3(Bend Test )	-	-	-
Cl-12(Impact Test )	-	-	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	-	-
Cl-14, Table-4 (ii)(Tee bars)	-	-	-
Cl-14, Table-4 (iii)(Bulb angles)	-	-	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	-	-
Cl-14, Table-4 (vi)(Round and square bars)	-	-	-
Cl-14, Table-4 (vii)(Bulb flats)	-	-	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	-	-
Cl-14, Table-4 (ix)(Channel sections)	-	-	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	-	-
Cl-13.3(Strength of joint )	-	-	-
Cl-15(Tolerances)	-	-	-
Cl-16.1(Retests)	-	-	-
Cl-16.2(Re-heat Treatment)	-	-	-

-
included w.e.f 04.08.2026

Delta Testing and Research Laboratories Private Limited (C5)

9179506

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-7(FREEDOM FROM DEFECTS)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1(Ladle Analysis)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	299.99	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Nb)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(V)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Ti)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-6(B)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (i)(Carbon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ii)(Manganese)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (v)(Silicon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vi)(Copper)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (viii)(Niobium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ix)(Titanium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (x)(Nitrogen)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.1(Number of Tensile Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.2(Tensile Test Pieces)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.1(Number of Bend Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.2(Bend Test Piece)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.3(Bend Test )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-12(Impact Test )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ii)(Tee bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iii)(Bulb angles)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vi)(Round and square bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vii)(Bulb flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (viii)(Sheet piling sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ix)(Channel sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13.3(Strength of joint )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-15(Tolerances)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.1(Retests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.2(Re-heat Treatment)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-6(MANUFACTURE)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-7(FREEDOM FROM DEFECTS)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1(Ladle Analysis)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Nb)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(V)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Ti)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-6(B)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (i)(Carbon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ii)(Manganese)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (v)(Silicon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vi)(Copper)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (viii)(Niobium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ix)(Titanium)	-	299.98	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (x)(Nitrogen)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.1(Number of Tensile Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.2(Tensile Test Pieces)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	299.97	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.1(Number of Bend Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.2(Bend Test Piece)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.3(Bend Test )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-12(Impact Test )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	299.98	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ii)(Tee bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iii)(Bulb angles)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vi)(Round and square bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vii)(Bulb flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (viii)(Sheet piling sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ix)(Channel sections)	-	299.99	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13.3(Strength of joint )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-15(Tolerances)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.1(Retests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.2(Re-heat Treatment)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-6(MANUFACTURE)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-7(FREEDOM FROM DEFECTS)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1(Ladle Analysis)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Nb)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(V)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Ti)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-6(B)	-	30	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (i)(Carbon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ii)(Manganese)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iii)(Sulphur)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iv)(Phosphorus)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (v)(Silicon)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vi)(Copper)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vii)(Vanadium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (viii)(Niobium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ix)(Titanium)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (x)(Nitrogen)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.1(Number of Tensile Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.2(Tensile Test Pieces)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.1(Number of Bend Tests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.2(Bend Test Piece)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.3(Bend Test )	-	300	-
Cl-12(Impact Test )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ii)(Tee bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iii)(Bulb angles)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vi)(Round and square bars)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vii)(Bulb flats)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (viii)(Sheet piling sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ix)(Channel sections)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13.3(Strength of joint )	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-15(Tolerances)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.1(Retests)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.2(Re-heat Treatment)	-	300	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-6(MANUFACTURE)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-7(FREEDOM FROM DEFECTS)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1(Ladle Analysis)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Nb)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(V)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Ti)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-6(B)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (i)(Carbon)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ii)(Manganese)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iii)(Sulphur)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iv)(Phosphorus)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (v)(Silicon)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vi)(Copper)	-	100	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	100	-
Cl-8.2, Table 2 (viii)(Niobium)	-	100	-
Cl-8.2, Table 2 (ix)(Titanium)	-	100	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	100	-
Cl-10.1(Number of Tensile Tests)	-	100	-
Cl-10.2(Tensile Test Pieces)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	100	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	100	-
Cl-11.1(Number of Bend Tests)	-	100	-
Cl-11.2(Bend Test Piece)	-	100	-
Cl-11.3(Bend Test )	-	100	-
Cl-12(Impact Test )	-	100	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	100	-
Cl-14, Table-4 (ii)(Tee bars)	-	100	-
Cl-14, Table-4 (iii)(Bulb angles)	-	100	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vi)(Round and square bars)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vii)(Bulb flats)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (viii)(Sheet piling sections)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ix)(Channel sections)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13.3(Strength of joint )	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-15(Tolerances)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.1(Retests)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.2(Re-heat Treatment)	-	100	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-6(MANUFACTURE)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-7(FREEDOM FROM DEFECTS)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1(Ladle Analysis)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Nb)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(V)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-5(Ti)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.1 & 8.2, Note-6(B)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (i)(Carbon)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ii)(Manganese)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (v)(Silicon)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vi)(Copper)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (viii)(Niobium)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (ix)(Titanium)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.1(Number of Tensile Tests)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.2(Tensile Test Pieces)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.1(Number of Bend Tests)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.2(Bend Test Piece)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-11.3(Bend Test )	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-12(Impact Test )	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ii)(Tee bars)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iii)(Bulb angles)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vi)(Round and square bars)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (vii)(Bulb flats)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-14, Table-4 (ix)(Channel sections)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-13.3(Strength of joint )	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-15(Tolerances)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.1(Retests)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.
Cl-16.2(Re-heat Treatment)	-	0	10% Discount to BIS for others 1.5 times of mentioned testing charges.

21 Aug, 2027

view Scope file
Included w.e.f-18.08.2026

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

5140804

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

E 250 TO E 650 (Grade - A, B, C, BR & B0 )

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	2000	-
Clause 11.3(Bend Test)	-	1000	-
Clause 12(Impact Test)	-	4000	-
Clause 15, Table 4(Dimension)	-	1000	-
Cl 18(Weight)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	-

14 Jun, 2027

-
-

NATIONAL TEST HOUSE-SR (NTH), Chennai

6122704

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	3000	-
Cl 11.3(Press)	-	1000	-
Cl 15(Length, Width & Thickness)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-

28 Nov, 2028

-
-

ARYAVRAT TEST HOUSE PRIVATE LIMITED

5191706

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

ALL

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	1000	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	1000	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	1000	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	1000	-
Cl-8.1 & 8.2, Note-5(Nb)	-	1000	-
Cl-8.1 & 8.2, Note-5(V)	-	1000	-
Cl-8.1 & 8.2, Note-5(Ti)	-	1000	-
Cl-8.1 & 8.2, Note-6(B)	-	1000	-
Cl-8.2, Table 2 (i)(Carbon)	-	1000	-
Cl-8.2, Table 2 (ii)(Manganese)	-	1000	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	1000	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	1000	-
Cl-8.2, Table 2 (v)(Silicon)	-	1000	-
Cl-8.2, Table 2 (vi)(Copper)	-	1000	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	1000	-
Cl-8.2, Table 2 (viii)(Niobium)	-	1000	-
Cl-8.2, Table 2 (ix)(Titanium)	-	1000	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1000	-
Cl-10.1(Number of Tensile Tests)	-	1000	-
Cl-10.2(Tensile Test Pieces)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	1000	-
Cl-11.1(Number of Bend Tests)	-	1000	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	1000	-
Cl-12(Impact Test )	-	1000	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	1000	-
Cl-13.3(Strength of joint )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	1000	-
Cl-16.2(Re-heat Treatment)	-	1000	-
Cl-6(MANUFACTURE)	-	500	-
Cl-7(FREEDOM FROM DEFECTS)	-	500	-
Cl-8.1(Ladle Analysis)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	1000	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	1000	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	1000	-
Cl-8.1 & 8.2, Note-5(Nb)	-	1000	-
Cl-8.1 & 8.2, Note-5(V)	-	1000	-
Cl-8.1 & 8.2, Note-5(Ti)	-	1000	-
Cl-8.1 & 8.2, Note-6(B)	-	1000	-
Cl-8.2, Table 2 (i)(Carbon)	-	1000	-
Cl-8.2, Table 2 (ii)(Manganese)	-	1000	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	1000	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	1000	-
Cl-8.2, Table 2 (v)(Silicon)	-	1000	-
Cl-8.2, Table 2 (vi)(Copper)	-	1000	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	1000	-
Cl-8.2, Table 2 (viii)(Niobium)	-	1000	-
Cl-8.2, Table 2 (ix)(Titanium)	-	1000	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1000	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	5000	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	1000	-
Cl-12(Impact Test )	-	5000	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	5000	-
Cl-13.3(Strength of joint )	-	2000	-
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	14000	-
Cl-16.2(Re-heat Treatment)	-	1000	-
Cl-6(MANUFACTURE)	-	500	-
Cl-7(FREEDOM FROM DEFECTS)	-	500	-
Cl-8.1(Ladle Analysis)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	1000	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	1000	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	1000	-
Cl-8.1 & 8.2, Note-5(Nb)	-	1000	-
Cl-8.1 & 8.2, Note-5(V)	-	1000	-
Cl-8.1 & 8.2, Note-5(Ti)	-	1000	-
Cl-8.1 & 8.2, Note-6(B)	-	1000	-
Cl-8.2, Table 2 (i)(Carbon)	-	1000	-
Cl-8.2, Table 2 (ii)(Manganese)	-	1000	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	1000	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	1000	-
Cl-8.2, Table 2 (v)(Silicon)	-	1000	-
Cl-8.2, Table 2 (vi)(Copper)	-	1000	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	1000	-
Cl-8.2, Table 2 (viii)(Niobium)	-	1000	-
Cl-8.2, Table 2 (ix)(Titanium)	-	1000	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1000	-
Cl-10.1(Number of Tensile Tests)	-	1000	-
Cl-10.2(Tensile Test Pieces)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	1000	-
Cl-11.1(Number of Bend Tests)	-	500	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	1000	-
Cl-12(Impact Test )	-	5000	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	5000	-
Cl-13.3(Strength of joint )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	1000	-
Cl-16.2(Re-heat Treatment)	-	1000	-

28 Nov, 2028

-
Included w.e.f 02.07.2026

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2062 (Part 2) (2026)

Structural Steel - Part 2 - Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

ALL

30500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	0	-
Cl-6(Manufacture )	-	0	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	9000	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	0	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	0	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	0	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	0	-
Cl-7.2, Table 3 (i)(Carbon)	-	0	-
Cl-7.2, Table 3 (ii)(Silicon)	-	0	-
Cl-7.2, Table 3 (iii)(Manganese)	-	0	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	0	-
Cl-7.2, Table 3 (v)(Sulphur)	-	0	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	0	-
Cl-7.2, Table 3 (vii)(Niobium)	-	0	-
Cl-7.2, Table 3 (viii)(Boron)	-	0	-
Cl-7.2, Table 3 (ix)(Titanium)	-	0	-
Cl-7.2, Table 3 (x)(Copper)	-	0	-
Cl-7.2, Table 3 (xi)(Nickel)	-	0	-
Cl-7.2, Table 3 (xii)(Chromium)	-	0	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	0	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	0	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	0	-
Cl-7.2, Table-4 (i)(Carbon)	-	0	-
Cl-7.2, Table-4 (ii)(Silicon)	-	0	-
Cl-7.2, Table-4 (iii)(Manganese)	-	0	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	0	-
Cl-7.2, Table-4 (v)(Sulphur)	-	0	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	0	-
Cl-7.2, Table-4 (vii)(Niobium)	-	0	-
Cl-7.2, Table-4 (viii)(Boron)	-	0	-
Cl-7.2, Table-4 (ix)(Titanium)	-	0	-
Cl-7.2, Table-4 (x)(Copper)	-	0	-
Cl-7.2, Table-4 (xi)(Nickel)	-	0	-
Cl-7.2, Table-4 (xii)(Chromium)	-	0	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	0	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	0	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	0	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	400	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	0	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	6500	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	0	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	0	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	0	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	0	-
Cl-8.3(Tensile Test Pieces)	-	0	-
Cl-8.4(Tensile Test)	-	6499.99	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	8100	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	8100	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	0	-
Cl-10.1(Weldability)	-	0	-
Cl-10.2.1(Hot-Forming)	-	0	-
Cl-10.2.3(Flangeability)	-	2500	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	0	-
Cl-11(Internal Soundness (Ultrasonic testing))	-	4500	-
Cl-12.1(Re-Tests )	-	30500	-
Cl-12.2(Re-Heat Treatment)	-	0	-
Cl-13(Freedom From Defect)	-	1000	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16(Calculation of Mass )	-	1000	-
Cl-18(Marking and Packing )	-	0	-
Cl-10.2.2(Cold Formability)	-	0	-

-
included w.e.f 17.08.2026

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

All

30500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	9000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	399.99	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	6500	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-
Cl-11.3(Bend Test )	-	2500	-
Cl-12(Impact Test )	-	8100	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	0	Grain Size Rs.4500 Ultrasonic Test Rs. 4000
Cl-13.3(Strength of joint )	-	0	4500
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	30500	-
Cl-16.2(Re-heat Treatment)	-	0	-

-
-

QUALITY INTERNATIONAL RESEARCH & LABORATORIES PRIVATE LIMITED

5197006

IS 2062 (Part 2) (2026)

Structural Steel - Part 2 - Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

Hot Rolled Quenched and Tempered Steel Plates, Sheets, Strips and Wide Flats

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	1000	-
Cl-6(Manufacture )	-	1000	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	1000	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	1000	1
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	1000	-
Cl-7.2, Table 3 (i)(Carbon)	-	1000	-
Cl-7.2, Table 3 (ii)(Silicon)	-	1000	-
Cl-7.2, Table 3 (iii)(Manganese)	-	1000	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table 3 (v)(Sulphur)	-	1000	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table 3 (vii)(Niobium)	-	1000	-
Cl-7.2, Table 3 (viii)(Boron)	-	1000	-
Cl-7.2, Table 3 (ix)(Titanium)	-	1000	-
Cl-7.2, Table 3 (x)(Copper)	-	1000	-
Cl-7.2, Table 3 (xi)(Nickel)	-	1000	-
Cl-7.2, Table 3 (xii)(Chromium)	-	1000	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	1000	-
Cl-7.2, Table-4 (i)(Carbon)	-	1000	-
Cl-7.2, Table-4 (ii)(Silicon)	-	1000	-
Cl-7.2, Table-4 (iii)(Manganese)	-	1000	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table-4 (v)(Sulphur)	-	1000	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table-4 (vii)(Niobium)	-	1000	-
Cl-7.2, Table-4 (viii)(Boron)	-	1000	-
Cl-7.2, Table-4 (ix)(Titanium)	-	1000	-
Cl-7.2, Table-4 (x)(Copper)	-	1000	-
Cl-7.2, Table-4 (xi)(Nickel)	-	1000	-
Cl-7.2, Table-4 (xii)(Chromium)	-	1000	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	1000	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	1000	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	1000	-
Cl-8.3(Tensile Test Pieces)	-	1000	-
Cl-8.4(Tensile Test)	-	1000	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	1000	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	1000	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	1000	-
Cl-10.1(Weldability)	-	1000	-
Cl-10.2.1(Hot-Forming)	-	1000	-
Cl-10.2.2(Cold Formability)	-	1000	-
Cl-10.2.3(Flangeability)	-	1000	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	1000	-
Cl-12.1(Re-Tests )	-	1000	-
Cl-12.2(Re-Heat Treatment)	-	1000	-
Cl-13(Freedom From Defect)	-	1000	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16(Calculation of Mass )	-	1000	-
Cl-18(Marking and Packing )	-	1000	-
Cl-4(General requirements)	-	1000	-
Cl-6(Manufacture )	-	1000	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	1000	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	1000	-
Cl-7.2, Table 3 (i)(Carbon)	-	1000	-
Cl-7.2, Table 3 (ii)(Silicon)	-	1000	-
Cl-7.2, Table 3 (iii)(Manganese)	-	1000	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table 3 (v)(Sulphur)	-	1000	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table 3 (vii)(Niobium)	-	1000	-
Cl-7.2, Table 3 (viii)(Boron)	-	1000	-
Cl-7.2, Table 3 (ix)(Titanium)	-	1000	-
Cl-7.2, Table 3 (x)(Copper)	-	1000	-
Cl-7.2, Table 3 (xi)(Nickel)	-	1000	-
Cl-7.2, Table 3 (xii)(Chromium)	-	1000	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	1000	-
Cl-7.2, Table-4 (i)(Carbon)	-	1000	-
Cl-7.2, Table-4 (ii)(Silicon)	-	1000	-
Cl-7.2, Table-4 (iii)(Manganese)	-	1000	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table-4 (v)(Sulphur)	-	1000	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table-4 (vii)(Niobium)	-	1000	-
Cl-7.2, Table-4 (viii)(Boron)	-	1000	-
Cl-7.2, Table-4 (ix)(Titanium)	-	1000	-
Cl-7.2, Table-4 (x)(Copper)	-	1000	-
Cl-7.2, Table-4 (xi)(Nickel)	-	1000	-
Cl-7.2, Table-4 (xii)(Chromium)	-	1000	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	1000	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	1000	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	1000	-
Cl-8.3(Tensile Test Pieces)	-	1000	-
Cl-8.4(Tensile Test)	-	1000	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	1000	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	1000	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	1000	-
Cl-10.1(Weldability)	-	1000	-
Cl-10.2.1(Hot-Forming)	-	1000	-
Cl-10.2.2(Cold Formability)	-	1000	-
Cl-10.2.3(Flangeability)	-	1000	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	1000	-
Cl-12.1(Re-Tests )	-	1000	-
Cl-12.2(Re-Heat Treatment)	-	1000	-
Cl-13(Freedom From Defect)	-	1000	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16(Calculation of Mass )	-	1000	-
Cl-18(Marking and Packing )	-	1000	-
Cl-4(General requirements)	-	1000	-
Cl-6(Manufacture )	-	1000	-
Cl-7.1(Ladle Analysis (Heat Analysis))	-	1000	-
Cl-7.1 & 7.3, Table 1 (C (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (Mn (S Grades ))	-	1000	-
Cl-7.1 & 7.3, Table 1 (S (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (P (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Si (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ni (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Mo (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (N (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (B (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Cu (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Nb (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Ti (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (V (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Zr (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 1 (Aluminium (S Grades) )	-	1000	-
Cl-7.1 & 7.3, Table 2(C (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mn (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(S (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(P (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Si (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cu (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ni (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Cr (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Mo (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(V (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Nb (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Ti (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(B (SG Grades))	-	1000	-
Cl-7.1 & 7.3, Table 2(Zr (SG Grades))	-	1000	-
Cl-7.2, Table 3 (i)(Carbon)	-	1000	-
Cl-7.2, Table 3 (ii)(Silicon)	-	1000	-
Cl-7.2, Table 3 (iii)(Manganese)	-	1000	-
Cl-7.2, Table 3 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table 3 (v)(Sulphur)	-	1000	-
Cl-7.2, Table 3 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table 3 (vii)(Niobium)	-	1000	-
Cl-7.2, Table 3 (viii)(Boron)	-	1000	-
Cl-7.2, Table 3 (ix)(Titanium)	-	1000	-
Cl-7.2, Table 3 (x)(Copper)	-	1000	-
Cl-7.2, Table 3 (xi)(Nickel)	-	1000	-
Cl-7.2, Table 3 (xii)(Chromium)	-	1000	-
Cl-7.2, Table 3 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table 3 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table 3 (xv)(Nitrogen)	-	1000	-
Cl-7.2, Table-4 (i)(Carbon)	-	1000	-
Cl-7.2, Table-4 (ii)(Silicon)	-	1000	-
Cl-7.2, Table-4 (iii)(Manganese)	-	1000	-
Cl-7.2, Table-4 (iv)(Phosphorus)	-	1000	-
Cl-7.2, Table-4 (v)(Sulphur)	-	1000	-
Cl-7.2, Table-4 (vi)(Vanadium)	-	1000	-
Cl-7.2, Table-4 (vii)(Niobium)	-	1000	-
Cl-7.2, Table-4 (viii)(Boron)	-	1000	-
Cl-7.2, Table-4 (ix)(Titanium)	-	1000	-
Cl-7.2, Table-4 (x)(Copper)	-	1000	-
Cl-7.2, Table-4 (xi)(Nickel)	-	1000	-
Cl-7.2, Table-4 (xii)(Chromium)	-	1000	-
Cl-7.2, Table-4 (xiii)(Molybdenum)	-	1000	-
Cl-7.2, Table-4 (xiv)(Zirconium)	-	1000	-
Cl-7.2, Table-4 (xv)(Nitrogen)	-	1000	-
Cl-7.3 & 7.4(Carbon Equivalent Value (CE))	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-≥3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 100 ≤ 125)	-	1000	-
Cl-8.1 & 8.4, Table 7(Minimum Yield Strength ReH, MPa Nominal Thickness,-> 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- ≥ 3 ≤ 50)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 50 ≤ 100)	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 100 ≤ 125 )	-	1000	-
Cl-8.1 & 8.4, Table 7(Tensile Strength Rm , MPa Nominal Thickness- > 125 ≤ 200)	-	1000	-
Cl-8.1 & 8.4, Table 7(Elongation A, Percentage Min at Gauge Length, Lo = 5.65√So- ≥ 3 ≤ 200)	-	1000	-
Cl-8.2(Location of Samples and Orientation of Test Pieces)	-	1000	-
Cl-8.3(Tensile Test Pieces)	-	1000	-
Cl-8.4(Tensile Test)	-	1000	-
Cl-9 & 9.4(Transverse Charpy V-notch properties a,c S Grades)	-	1000	-
Cl-9 & 9.4(Longitudinal Charpy V-notch properties SG Grades)	-	1000	-
Cl-9.1(Preparation of Impact Test Pieces (V-notch test))	-	1000	-
Cl-10.1(Weldability)	-	1000	-
Cl-10.2.1(Hot-Forming)	-	1000	-
Cl-10.2.2(Cold Formability)	-	1000	-
Cl-10.2.3(Flangeability)	-	1000	-
Cl-10.3(Hot-Dip Zinc-Coating)	-	1000	-
Cl-12.1(Re-Tests )	-	1000	-
Cl-12.2(Re-Heat Treatment)	-	1000	-
Cl-13(Freedom From Defect)	-	1000	-
Cl-14(Dimensions )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16(Calculation of Mass )	-	1000	-
Cl-18(Marking and Packing )	-	1000	-

-
-

QUALITY INTERNATIONAL RESEARCH & LABORATORIES PRIVATE LIMITED

5197006

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

Hot Rolled Medium & High Tensile

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	1000	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	1000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	1000	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	1000	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	1000	-
Cl-8.1 & 8.2, Note-5(Nb)	-	1000	-
Cl-8.1 & 8.2, Note-5(V)	-	1000	-
Cl-8.1 & 8.2, Note-5(Ti)	-	1000	-
Cl-8.1 & 8.2, Note-6(B)	-	1000	-
Cl-8.2, Table 2 (i)(Carbon)	-	1000	-
Cl-8.2, Table 2 (ii)(Manganese)	-	1000	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	1000	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	1000	-
Cl-8.2, Table 2 (v)(Silicon)	-	1000	-
Cl-8.2, Table 2 (vi)(Copper)	-	1000	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	1000	-
Cl-8.2, Table 2 (viii)(Niobium)	-	1000	-
Cl-8.2, Table 2 (ix)(Titanium)	-	1000	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	1000	-
Cl-10.1(Number of Tensile Tests)	-	1000	-
Cl-10.2(Tensile Test Pieces)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	1000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	1000	-
Cl-11.1(Number of Bend Tests)	-	1000	-
Cl-11.2(Bend Test Piece)	-	1000	-
Cl-11.3(Bend Test )	-	1000	-
Cl-12(Impact Test )	-	1000	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	1000	-
Cl-14, Table-4 (iii)(Bulb angles)	-	1000	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	1000	-
Cl-14, Table-4 (vi)(Round and square bars)	-	1000	-
Cl-14, Table-4 (vii)(Bulb flats)	-	1000	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	1000	-
Cl-14, Table-4 (ix)(Channel sections)	-	1000	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	1000	-
Cl-13.3(Strength of joint )	-	1000	-
Cl-15(Tolerances)	-	1000	-
Cl-16.1(Retests)	-	1000	-
Cl-16.2(Re-heat Treatment)	-	1000	-

-
Included w.e.f 19.05.2026

YORLAB LLP

7188606

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All Size

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 13(Y Groove Cracking Test)	-	700	-
Cl 12(Sudden Load Applied)	-	700	-
Cl 11.3(Press)	-	500	-
Cl 10.3(UTM)	-	700	-
Cl 7(Workmanship)	-	350	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	500	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	0	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	0	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	0	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	0	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	0	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	0	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	0	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	0	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	0	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	0	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	0	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	0	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	0	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	0	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	0	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	0	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 15, 16(Off Centre of Web)	-	0	-
Cl. 15, 16(Flange out of square (I beam))	-	0	-
Cl. 15, 16(Width of flange (I Beam))	-	0	-
Cl. 15, 16(Depth (I Beam))	-	0	-
Cl. 15, 16(Mass (Plate))	-	0	-
Cl. 15, 16(Flange Slope)	-	0	-
Cl. 15, 16(Web Thickness)	-	0	-
Cl. 15, 16(Flange Thickness)	-	0	-
Cl. 15, 16(Out of Square (Flat))	-	0	-
Cl. 15, 16(Width )	-	0	-
Cl. 15, 16(Thickness )	-	0	-
Cl. 15, 16(Sectional Area )	-	0	-
Cl. 15, 16(Camber (Angle))	-	0	-
Cl. 15, 16(Out of Square (Angle))	-	0	-
Cl. 15, 16(Weight)	-	0	-
Cl. 15, 16(Leg Length Difference (Angle))	-	0	-
Cl. 15, 16(Leg Length B (Angle))	-	0	-
Cl. 15, 16(Leg Length A (Angle))	-	0	-
Cl. 15, 16(Toe Radius R2)	-	0	-
Cl. 15, 16(Root Radius R1)	-	0	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
14.1(Soundness test)	-	0	-
14.2(Grain Size)	-	350	-
14.2(Inclusion)	-	400	-
Cl 7(Workmanship)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 18(Weight)	-	0	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 5(By Calculation)	-	0	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 6(By Calculation)	-	0	-
Clause 7(IS 2062)	-	500	-
Clause 11.3(IS 1599)	-	300	-
Clause 12(IS 1757)	-	450	-
Clause 15, Table 4(IS 2062)	-	500	-
16(Tolerance)	-	0	-
20(Marking)	-	100	-
20(MARKING)	-	0	-
8(Micro Alloying elements)	-	500	-
8(Niobium as Nb)	-	0	-
8(Vanadium as V)	-	0	-
8(Titanium as Ti)	-	0	-
10(Tensile Strength-IS:1608(P1)-22)	-	700	-
10(Yield Stress-IS:1608(P1)-22)	-	700	-
10(Elongation on SoA 5.65mm GL)	-	700	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimension -D)	-	0	-
15(Dimension -B)	-	0	-
15(Thickness - t)	-	0	-
15(Thickness - T)	-	0	-
15(Flange Slope)	-	0	-
15(Radius R1)	-	0	-
15(Radius R2)	-	0	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimension -D)	-	0	-
15(Dimension -B)	-	0	-
15(Thickness - t)	-	0	-
15(Thickness - T)	-	0	-
15(Radius R1)	-	0	-
15(Radius R2)	-	0	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimensions AxB)	-	0	-
15(Thickness - t)	-	0	-
15(Radius -R1)	-	0	-
15(Radius -R2)	-	0	-
15(Diameter)	-	0	-
15(Sectional Area)	-	0	-
15(Mass per metre)	-	0	-
15(Mass per metre)	-	0	-
15(Ovality)	-	0	-
15(Side Width)	-	0	-
15(Sectional Area)	-	0	-
15(Mass per metre)	-	0	-
15(Out of Square)	-	0	-
9(Preparation of test sample)	-	0	-
Clause 8, Table 1, Note 2(Aluminium)	-	500	-
Clause 8, Table 1, Note 5(Niobium)	-	500	-
Clause 8, Table 1, Note 5(Titanium)	-	500	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	500	-
Clause 8, Table 1, Note 6(Boron)	-	500	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	500	-
Clause 7(Freedom from Defect)	-	0	-
Clause 11.3(Bend Test)	-	0	-
Clause 12(Impact Test)	-	0	-
Clause 15, Table 4(Dimension)	-	0	-
5(General Requirements)	-	100	-
4(MARKING)	-	0	-

-
w.e.f. 07.08.2026

EKO PRO ENGINEERS PRIVATE LIMITED (32/37) GHAZIABAD

8164006

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

A/BR/B0/C

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	8000	-
Cl 15(Length, Width & Thickness)	-	8000	-
Cl 12(Sudden Load Applied)	-	1000	-
Cl 11.3(Press)	-	8000	-
Cl 10.3(UTM)	-	8000	-
Cl 7(Workmanship)	-	8000	-
Cl 18(Weight)	-	8000	-
Cl 15(Length, Width & Thickness)	-	8000	-
Cl 12(Sudden Load Applied)	-	8000	-
Cl 11.3(Press)	-	8000	-
Cl 10.3(UTM)	-	8000	-
Cl 7(Workmanship)	-	8000	-
Cl 18(Weight)	-	8000	-
Cl 15(Length, Width & Thickness)	-	8000	-
Cl 12(Sudden Load Applied)	-	8000	-
Cl 11.3(Press)	-	8000	-
Cl 10.3(UTM)	-	8000	-
Cl 7(Workmanship)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	8000	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	8000	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	8000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	8000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	8000	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	8000	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	8000	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	8000	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	8000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	8000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	8000	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	8000	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	8000	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	8000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	8000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	8000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	8000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	8000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	8000	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	8000	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	8000	-
Cl. 15, 16(Off Centre of Web)	-	8000	-
Cl. 15, 16(Flange out of square (I beam))	-	8000	-
Cl. 15, 16(Width of flange (I Beam))	-	8000	-
Cl. 15, 16(Depth (I Beam))	-	8000	-
Cl. 15, 16(Mass (Plate))	-	8000	-
Cl. 15, 16(Flange Slope)	-	8000	-
Cl. 15, 16(Web Thickness)	-	8000	-
Cl. 15, 16(Flange Thickness)	-	8000	-
Cl. 15, 16(Out of Square (Flat))	-	8000	-
Cl. 15, 16(Width )	-	8000	-
Cl. 15, 16(Thickness )	-	8000	-
Cl. 15, 16(Sectional Area )	-	8000	-
Cl. 15, 16(Camber (Angle))	-	8000	-
Cl. 15, 16(Out of Square (Angle))	-	8000	-
Cl. 15, 16(Weight)	-	8000	-
Cl. 15, 16(Leg Length Difference (Angle))	-	8000	-
Cl. 15, 16(Leg Length B (Angle))	-	8000	-
Cl. 15, 16(Leg Length A (Angle))	-	8000	-
Cl. 15, 16(Toe Radius R2)	-	8000	-
Cl. 15, 16(Root Radius R1)	-	8000	-
Cl 18(Weight)	-	8000	-
Cl 15(Length, Width & Thickness)	-	8000	-
Cl 12(Sudden Load Applied)	-	8000	-
Cl 11.3(Press)	-	8000	-
Cl 10.3(UTM)	-	8000	-
Cl 7(Workmanship)	-	8000	-
Cl 7(Workmanship)	-	8000	-
Cl 10.3(UTM)	-	8000	-
Cl 11.3(Press)	-	8000	-
Cl 12(Sudden Load Applied)	-	8000	-
Cl 15(Length, Width & Thickness)	-	8000	-
Cl 18(Weight)	-	8000	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	8000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	8000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	8000	-
Clause 8, Table 1, Note 5(By Calculation)	-	8000	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	8000	-
Clause 8, Table 1, Note 6(By Calculation)	-	8000	-
Clause 7(IS 2062)	-	8000	-
Clause 11.3(IS 1599)	-	8000	-
Clause 12(IS 1757)	-	8000	Facility for preparation of test specimen not avaiable for impact test .
16(Tolerance)	-	8000	-
20(Marking)	-	8000	-
20(MARKING)	-	8000	-
8(Micro Alloying elements)	-	8000	-
8(Niobium as Nb)	-	8000	-
8(Titanium as Ti)	-	8000	-
10(Tensile Strength-IS:1608(P1)-22)	-	8000	-
10(Yield Stress-IS:1608(P1)-22)	-	8000	-
10(Elongation on SoA 5.65mm GL)	-	8000	-
15(Mass -SOP MT-23)	-	8000	-
15(Sectional Area)	-	8000	-
15(Dimension -D)	-	8000	-
15(Dimension -B)	-	8000	-
15(Thickness - t)	-	8000	-
15(Thickness - T)	-	8000	-
15(Flange Slope)	-	8000	-
15(Radius R1)	-	8000	-
15(Radius R2)	-	8000	-
15(Mass -SOP MT-23)	-	8000	-
15(Sectional Area)	-	8000	-
15(Dimension -D)	-	8000	-
15(Dimension -B)	-	8000	-
15(Thickness - t)	-	8000	-
15(Thickness - T)	-	8000	-
15(Radius R1)	-	8000	-
15(Radius R2)	-	8000	-
15(Mass -SOP MT-23)	-	8000	-
15(Sectional Area)	-	8000	-
15(Dimensions AxB)	-	8000	-
15(Thickness - t)	-	8000	-
15(Radius -R1)	-	8000	-
15(Radius -R2)	-	8000	-
15(Diameter)	-	8000	-
15(Sectional Area)	-	8000	-
15(Mass per metre)	-	8000	-
15(Mass per metre)	-	8000	-
15(Ovality)	-	8000	-
15(Side Width)	-	8000	-
15(Sectional Area)	-	8000	-
15(Mass per metre)	-	8000	-
15(Out of Square)	-	8000	-
9(Preparation of test sample)	-	8000	-
Clause 8, Table 1, Note 2(Aluminium)	-	8000	-
Clause 8, Table 1, Note 5(Niobium)	-	8000	-
Clause 8, Table 1, Note 5(Titanium)	-	8000	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	8000	-
Clause 8, Table 1, Note 6(Boron)	-	8000	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	8000	-
Clause 7(Freedom from Defect)	-	8000	-
Clause 11.3(Bend Test)	-	8000	-
Clause 12(Impact Test)	-	8000	Facility for preparation of test specimen not avaiable for impact test.
Clause 15, Table 4(Dimension)	-	8000	-
5(General Requirements)	-	8000	-
4(MARKING)	-	8000	-
8(Vanadium as V)	-	8000	-
Cl 18(Weight)	-	8000	-

27 May, 2028

-
-

Gravitas Laboratories Private Limited, Greater Noida

8182606

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	12500	-
Cl 15(Length, Width & Thickness)	-	12500	-
Cl 13(Y Groove Cracking Test)	-	0	5500
Cl 12(Sudden Load Applied)	-	12500	-
Cl 11.3(Press)	-	12500	-
Cl 10.3(UTM)	-	12500	-
Cl 7(Workmanship)	-	12500	-
Cl 18(Weight)	-	12500	-
Cl 15(Length, Width & Thickness)	-	12500	-
Cl 13(Y Groove Cracking Test)	-	0	5500
Cl 12(Sudden Load Applied)	-	12500	-
Cl 11.3(Press)	-	12500	-
Cl 10.3(UTM)	-	12500	-
Cl 7(Workmanship)	-	12500	-
Cl 18(Weight)	-	12500	-
Cl 15(Length, Width & Thickness)	-	12500	-
Cl 13(Y Groove Cracking Test)	-	0	5500
Cl 12(Sudden Load Applied)	-	12500	-
Cl 11.3(Press)	-	12500	-
Cl 10.3(UTM)	-	12500	-
Cl 7(Workmanship)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	12500	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	12500	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	12500	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	12500	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	12500	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	12500	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	12500	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	12500	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	12500	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	12500	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	12500	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	12500	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	12500	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	12500	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	12500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	12500	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	12500	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	12500	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	12500	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	12500	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12500	-
Cl. 15, 16(Off Centre of Web)	-	12500	-
Cl. 15, 16(Flange out of square (I beam))	-	12500	-
Cl. 15, 16(Width of flange (I Beam))	-	12500	-
Cl. 15, 16(Depth (I Beam))	-	12500	-
Cl. 15, 16(Mass (Plate))	-	12500	-
Cl. 15, 16(Flange Slope)	-	12500	-
Cl. 15, 16(Web Thickness)	-	12500	-
Cl. 15, 16(Flange Thickness)	-	12500	-
Cl. 15, 16(Out of Square (Flat))	-	12500	-
Cl. 15, 16(Width )	-	12500	-
Cl. 15, 16(Thickness )	-	12500	-
Cl. 15, 16(Sectional Area )	-	12500	-
Cl. 15, 16(Camber (Angle))	-	12500	-
Cl. 15, 16(Out of Square (Angle))	-	12500	-
Cl. 15, 16(Weight)	-	12500	-
Cl. 15, 16(Leg Length Difference (Angle))	-	12500	-
Cl. 15, 16(Leg Length B (Angle))	-	12500	-
Cl. 15, 16(Leg Length A (Angle))	-	12500	-
Cl. 15, 16(Toe Radius R2)	-	12500	-
Cl. 15, 16(Root Radius R1)	-	12500	-
Cl 18(Weight)	-	12500	-
Cl 15(Length, Width & Thickness)	-	12500	-
Cl 13(Y Groove Cracking Test)	-	0	5500
Cl 12(Sudden Load Applied)	-	12500	-
Cl 11.3(Press)	-	12500	-
Cl 10.3(UTM)	-	12500	-
Cl 7(Workmanship)	-	12500	-
14.1(Soundness test)	-	0	5500
14.2(Grain Size)	-	0	5500
14.2(Inclusion)	-	0	5500
Cl 7(Workmanship)	-	12500	-
Cl 10.3(UTM)	-	12500	-
Cl 11.3(Press)	-	12500	-
Cl 12(Sudden Load Applied)	-	12500	-
Cl 13(Y Groove Cracking Test)	-	0	5500
Cl 15(Length, Width & Thickness)	-	12500	-
Cl 18(Weight)	-	12500	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	12500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	12500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	12500	-
Clause 8, Table 1, Note 5(By Calculation)	-	12500	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	12500	-
Clause 7(IS 2062)	-	12500	-
Clause 11.3(IS 1599)	-	12500	-
Clause 12(IS 1757)	-	12500	-
Clause 15, Table 4(IS 2062)	-	12500	-
16(Tolerance)	-	12500	-
20(Marking)	-	0	-
20(MARKING)	-	0	-
8(Micro Alloying elements)	-	12500	-
8(Titanium as Ti)	-	12500	-
10(Tensile Strength-IS:1608(P1)-22)	-	12500	-
10(Elongation on SoA 5.65mm GL)	-	12500	-
15(Mass -SOP MT-23)	-	12500	-
15(Sectional Area)	-	12500	-
15(Dimension -D)	-	12500	-
15(Dimension -B)	-	12500	-
15(Thickness - t)	-	12500	-
15(Thickness - T)	-	12500	-
15(Flange Slope)	-	12500	-
15(Radius R1)	-	12500	-
15(Radius R2)	-	12500	-
15(Mass -SOP MT-23)	-	12500	-
15(Sectional Area)	-	12500	-
15(Dimension -D)	-	12500	-
15(Dimension -B)	-	12500	-
15(Thickness - t)	-	12500	-
15(Thickness - T)	-	12500	-
15(Radius R1)	-	12500	-
15(Radius R2)	-	12500	-
15(Mass -SOP MT-23)	-	12500	-
15(Sectional Area)	-	12500	-
15(Dimensions AxB)	-	12500	-
15(Thickness - t)	-	12500	-
15(Radius -R1)	-	12500	-
15(Radius -R2)	-	12500	-
15(Diameter)	-	12500	-
15(Sectional Area)	-	12500	-
15(Mass per metre)	-	12500	-
15(Mass per metre)	-	12500	-
15(Ovality)	-	12500	-
15(Side Width)	-	12500	-
15(Sectional Area)	-	12500	-
15(Mass per metre)	-	12500	-
15(Out of Square)	-	12500	-
9(Preparation of test sample)	-	12500	-
Clause 8, Table 1, Note 2(Aluminium)	-	12500	-
Clause 8, Table 1, Note 5(Niobium)	-	12500	-
Clause 8, Table 1, Note 5(Titanium)	-	12500	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	12500	-
Clause 8, Table 1, Note 6(Boron)	-	12500	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	12500	-
Clause 7(Freedom from Defect)	-	12500	-
Clause 11.3(Bend Test)	-	12500	-
Clause 12(Impact Test)	-	12500	-
Clause 15, Table 4(Dimension)	-	12500	-
5(General Requirements)	-	12500	-
4(MARKING)	-	0	-
Clause 8, Table 1, Note 6(By Calculation)	-	12500	-
8(Niobium as Nb)	-	12500	-
8(Vanadium as V)	-	12500	-
10(Yield Stress-IS:1608(P1)-22)	-	12500	-

-
Included w.e.f. 10.04.2026

ARYAVRAT TEST HOUSE PRIVATE LIMITED

5191706

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All Type (Exclusion : Cl 13 Y Groove Crackability, Cl 14 Other Tests )

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 13(Y Groove Cracking Test)	-	500	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 11.3(Press)	-	500	-
Cl 10.3(UTM)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 13(Y Groove Cracking Test)	-	500	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 11.3(Press)	-	500	-
Cl 10.3(UTM)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 13(Y Groove Cracking Test)	-	500	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 11.3(Press)	-	500	-
Cl 10.3(UTM)	-	500	-
Cl 7(Workmanship)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	500	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	500	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	500	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	500	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	500	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	500	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	500	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	500	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	500	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	500	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	500	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	500	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	500	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	500	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	500	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	500	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 15, 16(Off Centre of Web)	-	500	-
Cl. 15, 16(Flange out of square (I beam))	-	500	-
Cl. 15, 16(Width of flange (I Beam))	-	500	-
Cl. 15, 16(Depth (I Beam))	-	500	-
Cl. 15, 16(Mass (Plate))	-	500	-
Cl. 15, 16(Flange Slope)	-	500	-
Cl. 15, 16(Web Thickness)	-	500	-
Cl. 15, 16(Flange Thickness)	-	500	-
Cl. 15, 16(Out of Square (Flat))	-	500	-
Cl. 15, 16(Width )	-	500	-
Cl. 15, 16(Thickness )	-	500	-
Cl. 15, 16(Sectional Area )	-	500	-
Cl. 15, 16(Camber (Angle))	-	500	-
Cl. 15, 16(Out of Square (Angle))	-	500	-
Cl. 15, 16(Weight)	-	500	-
Cl. 15, 16(Leg Length Difference (Angle))	-	500	-
Cl. 15, 16(Leg Length B (Angle))	-	500	-
Cl. 15, 16(Leg Length A (Angle))	-	500	-
Cl. 15, 16(Toe Radius R2)	-	500	-
Cl. 15, 16(Root Radius R1)	-	500	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 13(Y Groove Cracking Test)	-	500	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 11.3(Press)	-	500	-
Cl 10.3(UTM)	-	500	-
Cl 7(Workmanship)	-	500	-
14.1(Soundness test)	-	500	-
14.2(Grain Size)	-	500	-
14.2(Inclusion)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 10.3(UTM)	-	500	-
Cl 11.3(Press)	-	500	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 13(Y Groove Cracking Test)	-	500	-
Cl 15(Length, Width & Thickness)	-	500	-
Cl 18(Weight)	-	500	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(By Calculation)	-	500	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 6(By Calculation)	-	500	-
Clause 7(IS 2062)	-	500	-
Clause 11.3(IS 1599)	-	500	-
Clause 12(IS 1757)	-	500	-
Clause 15, Table 4(IS 2062)	-	500	-
16(Tolerance)	-	500	-
20(Marking)	-	500	-
20(MARKING)	-	500	-
8(Micro Alloying elements)	-	500	-
8(Niobium as Nb)	-	500	-
8(Vanadium as V)	-	500	-
8(Titanium as Ti)	-	500	-
10(Tensile Strength-IS:1608(P1)-22)	-	500	-
10(Yield Stress-IS:1608(P1)-22)	-	500	-
10(Elongation on SoA 5.65mm GL)	-	500	-
15(Sectional Area)	-	500	-
15(Mass -SOP MT-23)	-	500	-
15(Dimension -D)	-	500	-
15(Dimension -B)	-	500	-
15(Thickness - t)	-	500	-
15(Thickness - T)	-	500	-
15(Flange Slope)	-	500	-
15(Radius R1)	-	500	-
15(Radius R2)	-	500	-
15(Mass -SOP MT-23)	-	500	-
15(Sectional Area)	-	500	-
15(Dimension -D)	-	500	-
15(Dimension -B)	-	500	-
15(Thickness - t)	-	500	-
15(Thickness - T)	-	500	-
15(Radius R1)	-	500	-
15(Radius R2)	-	500	-
15(Mass -SOP MT-23)	-	500	-
15(Sectional Area)	-	500	-
15(Dimensions AxB)	-	500	-
15(Thickness - t)	-	500	-
15(Radius -R1)	-	500	-
15(Radius -R2)	-	500	-
15(Diameter)	-	500	-
15(Sectional Area)	-	500	-
15(Mass per metre)	-	500	-
15(Mass per metre)	-	500	-
15(Ovality)	-	500	-
15(Side Width)	-	500	-
15(Sectional Area)	-	500	-
15(Mass per metre)	-	500	-
15(Out of Square)	-	500	-
9(Preparation of test sample)	-	500	-
Clause 8, Table 1, Note 2(Aluminium)	-	500	-
Clause 8, Table 1, Note 5(Niobium)	-	500	-
Clause 8, Table 1, Note 5(Titanium)	-	500	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	500	-
Clause 8, Table 1, Note 6(Boron)	-	500	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	500	-
Clause 7(Freedom from Defect)	-	500	-
Clause 11.3(Bend Test)	-	500	-
Clause 12(Impact Test)	-	500	-
Clause 15, Table 4(Dimension)	-	500	-
5(General Requirements)	-	500	-
4(MARKING)	-	100	-

28 Nov, 2028

-
Included w.e.f 31.12.2025 "Cl 13 (Y Groove Cracking Test) 14.1 (Soundness test)"

National Institute of secondary steel technology

9135004

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All Grades/ All sizes/ All Designation

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	1500	-
Cl 11.3(Press)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl 12(Sudden Load Applied)	-	1500	-

24 Oct, 2028

-
-

Atckon Laboratories LLP, Bahadurgarh

8186436

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

ALL GRADES

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	15000	-
Cl 15(Length, Width & Thickness)	-	15000	-
Cl 13(Y Groove Cracking Test)	-	15000	-
Cl 12(Sudden Load Applied)	-	15000	-
Cl 11.3(Press)	-	15000	-
Cl 10.3(UTM)	-	15000	-
Cl 7(Workmanship)	-	15000	-
Cl 18(Weight)	-	15000	-
Cl 15(Length, Width & Thickness)	-	15000	-
Cl 13(Y Groove Cracking Test)	-	15000	-
Cl 12(Sudden Load Applied)	-	15000	-
Cl 11.3(Press)	-	15000	-
Cl 10.3(UTM)	-	15000	-
Cl 7(Workmanship)	-	15000	-
Cl 18(Weight)	-	15000	-
Cl 15(Length, Width & Thickness)	-	15000	-
Cl 13(Y Groove Cracking Test)	-	15000	-
Cl 12(Sudden Load Applied)	-	15000	-
Cl 11.3(Press)	-	15000	-
Cl 10.3(UTM)	-	15000	-
Cl 7(Workmanship)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	15000	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	15000	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	15000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	15000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	15000	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	15000	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	15000	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	15000	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	15000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	15000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	15000	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	15000	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	15000	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	15000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	15000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	15000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	15000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	15000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	15000	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	15000	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	15000	-
Cl. 15, 16(Off Centre of Web)	-	15000	-
Cl. 15, 16(Flange out of square (I beam))	-	15000	-
Cl. 15, 16(Width of flange (I Beam))	-	15000	-
Cl. 15, 16(Depth (I Beam))	-	15000	-
Cl. 15, 16(Mass (Plate))	-	15000	-
Cl. 15, 16(Flange Slope)	-	15000	-
Cl. 15, 16(Web Thickness)	-	15000	-
Cl. 15, 16(Flange Thickness)	-	15000	-
Cl. 15, 16(Out of Square (Flat))	-	15000	-
Cl. 15, 16(Width )	-	15000	-
Cl. 15, 16(Thickness )	-	15000	-
Cl. 15, 16(Sectional Area )	-	15000	-
Cl. 15, 16(Camber (Angle))	-	15000	-
Cl. 15, 16(Out of Square (Angle))	-	15000	-
Cl. 15, 16(Weight)	-	15000	-
Cl. 15, 16(Leg Length Difference (Angle))	-	15000	-
Cl. 15, 16(Leg Length B (Angle))	-	15000	-
Cl. 15, 16(Leg Length A (Angle))	-	15000	-
Cl. 15, 16(Toe Radius R2)	-	15000	-
Cl. 15, 16(Root Radius R1)	-	15000	-
Cl 18(Weight)	-	15000	-
Cl 15(Length, Width & Thickness)	-	15000	-
Cl 13(Y Groove Cracking Test)	-	15000	-
Cl 12(Sudden Load Applied)	-	15000	-
Cl 11.3(Press)	-	15000	-
Cl 10.3(UTM)	-	15000	-
Cl 7(Workmanship)	-	15000	-
14.1(Soundness test)	-	15000	-
14.2(Grain Size)	-	15000	-
14.2(Inclusion)	-	15000	-
Cl 7(Workmanship)	-	15000	-
Cl 10.3(UTM)	-	15000	-
Cl 11.3(Press)	-	15000	-
Cl 12(Sudden Load Applied)	-	15000	-
Cl 13(Y Groove Cracking Test)	-	15000	-
Cl 15(Length, Width & Thickness)	-	15000	-
Cl 18(Weight)	-	15000	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	15000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	15000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	15000	-
Clause 8, Table 1, Note 5(By Calculation)	-	15000	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	15000	-
Clause 8, Table 1, Note 6(By Calculation)	-	15000	-
Clause 7(IS 2062)	-	15000	-
Clause 11.3(IS 1599)	-	15000	-
Clause 12(IS 1757)	-	15000	-
Clause 15, Table 4(IS 2062)	-	15000	-
16(Tolerance)	-	15000	-
20(Marking)	-	15000	-
20(MARKING)	-	15000	-
8(Micro Alloying elements)	-	15000	-
8(Niobium as Nb)	-	15000	-
8(Vanadium as V)	-	15000	-
8(Titanium as Ti)	-	15000	-
10(Tensile Strength-IS:1608(P1)-22)	-	15000	-
10(Yield Stress-IS:1608(P1)-22)	-	15000	-
10(Elongation on SoA 5.65mm GL)	-	15000	-
15(Mass -SOP MT-23)	-	15000	-
15(Sectional Area)	-	15000	-
15(Dimension -D)	-	15000	-
15(Dimension -B)	-	15000	-
15(Thickness - t)	-	15000	-
15(Thickness - T)	-	15000	-
15(Flange Slope)	-	15000	-
15(Radius R1)	-	15000	-
15(Radius R2)	-	15000	-
15(Mass -SOP MT-23)	-	15000	-
15(Sectional Area)	-	15000	-
15(Dimension -D)	-	15000	-
15(Dimension -B)	-	15000	-
15(Thickness - t)	-	15000	-
15(Thickness - T)	-	15000	-
15(Radius R1)	-	15000	-
15(Radius R2)	-	15000	-
15(Mass -SOP MT-23)	-	15000	-
15(Sectional Area)	-	15000	-
15(Dimensions AxB)	-	15000	-
15(Thickness - t)	-	15000	-
15(Radius -R1)	-	15000	-
15(Radius -R2)	-	15000	-
15(Diameter)	-	15000	-
15(Sectional Area)	-	15000	-
15(Mass per metre)	-	15000	-
15(Mass per metre)	-	15000	-
15(Ovality)	-	15000	-
15(Side Width)	-	15000	-
15(Sectional Area)	-	15000	-
15(Mass per metre)	-	15000	-
15(Out of Square)	-	15000	-
9(Preparation of test sample)	-	15000	-
Clause 8, Table 1, Note 2(Aluminium)	-	15000	-
Clause 8, Table 1, Note 5(Niobium)	-	15000	-
Clause 8, Table 1, Note 5(Titanium)	-	15000	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	15000	-
Clause 8, Table 1, Note 6(Boron)	-	15000	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	15000	-
Clause 7(Freedom from Defect)	-	15000	-
Clause 11.3(Bend Test)	-	15000	-
Clause 12(Impact Test)	-	15000	-
Clause 15, Table 4(Dimension)	-	15000	-
5(General Requirements)	-	15000	-
4(MARKING)	-	15000	-

-
Included w.e.f. 09.10.2025

Unique Test House LLP

9134536

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

E250,E275,E33,E350,E410,E450,E550,E600,E650

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	2000	....
Cl 11.3(Press)	-	500	....
Cl 18(Weight)	-	200	....
Cl 15(Length, Width & Thickness)	-	100	...
Cl 13(Y Groove Cracking Test)	-	500	...
Cl 12(Sudden Load Applied)	-	100	...
Cl 7(Workmanship)	-	100	...
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	100	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	100	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	100	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	100	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	100	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	500	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	100	-
Cl. 15, 16(Off Centre of Web)	-	200	-
Cl. 15, 16(Flange out of square (I beam))	-	200	-
Cl. 15, 16(Width of flange (I Beam))	-	200	-
Cl. 15, 16(Depth (I Beam))	-	200	-
Cl. 15, 16(Mass (Plate))	-	200	-
Cl. 15, 16(Flange Slope)	-	200	-
Cl. 15, 16(Web Thickness)	-	200	-
Cl. 15, 16(Flange Thickness)	-	200	-
Cl. 15, 16(Out of Square (Flat))	-	200	-
Cl. 15, 16(Width )	-	200	-
Cl. 15, 16(Thickness )	-	200	-
Cl. 15, 16(Sectional Area )	-	200	-
Cl. 15, 16(Camber (Angle))	-	200	-
Cl. 15, 16(Out of Square (Angle))	-	200	-
Cl. 15, 16(Leg Length Difference (Angle))	-	200	-
Cl. 15, 16(Leg Length B (Angle))	-	200	-
Cl. 15, 16(Leg Length A (Angle))	-	200	-
Cl. 15, 16(Toe Radius R2)	-	200	-
Cl. 15, 16(Root Radius R1)	-	200	-

07 Sep, 2028

-
-

NBML Building Materials Testing Lab LLP, Raipur

5171706

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 15(Length, Width & Thickness)	-	150	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Cl 10.3(UTM)	-	475	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	160	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	250	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	475	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	50	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	40	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Clause 11.3(IS 1599)	-	500	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
Cl 12(Sudden Load Applied)	-	350	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
16(Tolerance)	-	200	1.15% Discount for BIS. 2.GST @ 18% extra as applicable presently any change by the Govt either increase or decrease in GST will be applicable at the time of placement of order.
20(Marking)	-	0	-

29 Sep, 2028

-
-

Excel Surveyors Pvt. Ltd., Kolkata

5135906

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

Grade - E250, E275, E300, E350, E410, E450, E550, E600, E650, Quality - A, BR, B0, C.

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	0	Included Chemical, Mechanical Metallography & NDT test. (for dimension the testing charges will be 1000)
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	Exclusion : Y groove cracking test
Cl 12(Sudden Load Applied)	-	700	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	50	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	500	(for chemical the testing charges will be 500)
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	0	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	0	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	0	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	0	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	0	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	0	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	0	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	0	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	0	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	0	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	0	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	0	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	0	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	450	(for Mechanical the testing charges will be 450)
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	0	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	0	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	0	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	0	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	0	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	0	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	0	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	0	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	0	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 15, 16(Off Centre of Web)	-	0	-
Cl. 15, 16(Flange out of square (I beam))	-	0	-
Cl. 15, 16(Width of flange (I Beam))	-	0	-
Cl. 15, 16(Depth (I Beam))	-	0	-
Cl. 15, 16(Mass (Plate))	-	0	-
Cl. 15, 16(Flange Slope)	-	0	-
Cl. 15, 16(Web Thickness)	-	0	-
Cl. 15, 16(Flange Thickness)	-	0	-
Cl. 15, 16(Out of Square (Flat))	-	50	-
Cl. 15, 16(Width )	-	0	-
Cl. 15, 16(Thickness )	-	0	-
Cl. 15, 16(Sectional Area )	-	0	-
Cl. 15, 16(Camber (Angle))	-	0	-
Cl. 15, 16(Out of Square (Angle))	-	0	-
Cl. 15, 16(Weight)	-	0	-
Cl. 15, 16(Leg Length Difference (Angle))	-	0	-
Cl. 15, 16(Leg Length B (Angle))	-	0	-
Cl. 15, 16(Leg Length A (Angle))	-	0	-
Cl. 15, 16(Toe Radius R2)	-	0	-
Cl. 15, 16(Root Radius R1)	-	0	-
Cl 18(Weight)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 7(Workmanship)	-	0	-
14.1(Soundness test)	-	800	(for NDT test the testing charges will be 800)
14.2(Grain Size)	-	250	(for Grain size determination the testing charges will be 250)
14.2(Inclusion)	-	250	(for Inclusion determination the testing charges will be 250)
Cl 7(Workmanship)	-	0	-
Cl 10.3(UTM)	-	0	-
Cl 11.3(Press)	-	0	-
Cl 12(Sudden Load Applied)	-	0	-
Cl 13(Y Groove Cracking Test)	-	0	-
Cl 15(Length, Width & Thickness)	-	0	-
Cl 18(Weight)	-	0	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 5(By Calculation)	-	0	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	0	-
Clause 8, Table 1, Note 6(By Calculation)	-	0	-
Clause 7(IS 2062)	-	50	-
Clause 11.3(IS 1599)	-	500	-
Clause 12(IS 1757)	-	0	-
Clause 15, Table 4(IS 2062)	-	1000	(for Dimension of any structural steel products the testing charges will be 1000)
16(Tolerance)	-	0	-
20(Marking)	-	50	-
20(MARKING)	-	0	-
8(Micro Alloying elements)	-	0	-
8(Niobium as Nb)	-	0	-
8(Vanadium as V)	-	0	-
8(Titanium as Ti)	-	0	-
10(Tensile Strength-IS:1608(P1)-22)	-	0	-
10(Yield Stress-IS:1608(P1)-22)	-	0	-
10(Elongation on SoA 5.65mm GL)	-	0	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimension -D)	-	0	-
15(Dimension -B)	-	0	-
15(Thickness - t)	-	0	-
15(Thickness - T)	-	0	-
15(Flange Slope)	-	0	-
15(Radius R1)	-	0	-
15(Radius R2)	-	0	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimension -D)	-	0	-
15(Dimension -B)	-	0	-
15(Thickness - t)	-	0	-
15(Thickness - T)	-	0	-
15(Radius R1)	-	0	-
15(Radius R2)	-	0	-
15(Mass -SOP MT-23)	-	0	-
15(Sectional Area)	-	0	-
15(Dimensions AxB)	-	0	-
15(Thickness - t)	-	0	-
15(Radius -R1)	-	0	-
15(Radius -R2)	-	0	-
15(Diameter)	-	0	-
15(Sectional Area)	-	0	-
15(Mass per metre)	-	0	-
15(Mass per metre)	-	0	-
15(Ovality)	-	0	-
15(Side Width)	-	0	-
15(Sectional Area)	-	0	-
15(Mass per metre)	-	0	-
15(Out of Square)	-	0	-
9(Preparation of test sample)	-	0	-
Clause 8, Table 1, Note 2(Aluminium)	-	0	-
Clause 8, Table 1, Note 5(Niobium)	-	0	-
Clause 8, Table 1, Note 5(Titanium)	-	0	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	0	-
Clause 8, Table 1, Note 6(Boron)	-	0	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	0	-
Clause 7(Freedom from Defect)	-	0	-
Clause 11.3(Bend Test)	-	0	-
Clause 12(Impact Test)	-	0	-
Clause 15, Table 4(Dimension)	-	0	-
5(General Requirements)	-	0	-
4(MARKING)	-	0	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-

31 Dec, 2026

-
Included w.e.f 04.11.2025 Exclusion: Cl 13 (Y Groove Cracking Test)

Bharat Test House Pvt. Ltd. 1668 Sonipat

9168306

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	5000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	5000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	5000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	5000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	5000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	2000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1500	-
14.2(Grain Size)	-	2000	-

-
-

Ghaziabad Testing Laboratories Pvt Ltd, Ghaziabad

8125006

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All Grades with Quality A

15650.00 View breakup
-

Clause No.	Exclusion	Remark
Cl 15(Length, Width & Thickness)	-	Gst extra
Cl 10.3(UTM)	-	Gst extra
Cl 12(Sudden Load Applied)	-	Gst extra
Cl 7(Workmanship)	-	Gst extra
Cl 18(Weight)	-	Gst extra
Cl 15(Length, Width & Thickness)	-	Gst extra
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	Gst extra
Cl. 15(Cl. 15 Channel Section: Camber)	-	Gst extra
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	Gst extra
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	Gst extra
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	Gst extra
Cl. 15(Cl. 15 Channel Section: Depth)	-	Gst extra
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	Gst extra
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	Gst extra
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	Gst extra
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	Gst extra
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	Gst extra
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	Gst extra
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	Gst extra
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	Gst extra
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	Gst extra
Cl 11.3(Press)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	Gst extra
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	Gst extra
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	Gst extra
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	Gst extra

30 Sep, 2027

-
-

ELCA Laboratories, Navi Mumbai

7169736

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

Grade E 250/E275/E300/E350/E410/E450/E550/E600

0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 11.3(Bend Test)	-	300	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	700	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	700	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	700	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl 18(Weight)	-	150	-
14.2(Grain Size)	-	600	-
Clause 12(Impact Test)	-	1500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Clause 11.3(Bend Test)	-	300	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
14.2(Grain Size)	-	600	-
Clause 12(Impact Test)	-	1500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Clause 11.3(Bend Test)	-	300	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
14.2(Grain Size)	-	600	-
Clause 12(Impact Test)	-	1500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	150	-
Cl 15(Length, Width & Thickness)	-	1500	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	700	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	1500	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	700	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	1500	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	700	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	150	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	150	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	150	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	150	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	150	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	0	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	150	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	150	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	300	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	150	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	150	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	150	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	150	-
Cl 18(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	1500	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	700	-
14.2(Inclusion)	-	750	-
Cl 10.3(UTM)	-	700	-
Cl 11.3(Press)	-	300	-
Cl 18(Weight)	-	500	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	150	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	150	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	150	-
Clause 8, Table 1, Note 5(By Calculation)	-	0	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	150	-
Clause 8, Table 1, Note 6(By Calculation)	-	0	-
Clause 7(IS 2062)	-	1500	-
Clause 11.3(IS 1599)	-	300	-
Clause 12(IS 1757)	-	1500	-
Clause 15, Table 4(IS 2062)	-	1500	-
8(Micro Alloying elements)	-	0	-
8(Niobium as Nb)	-	150	-
8(Vanadium as V)	-	150	-
8(Titanium as Ti)	-	150	-
10(Tensile Strength-IS:1608(P1)-22)	-	700	-
10(Yield Stress-IS:1608(P1)-22)	-	700	-
10(Elongation on SoA 5.65mm GL)	-	700	-
Clause 8, Table 1, Note 2(Aluminium)	-	150	-
Clause 8, Table 1, Note 5(Niobium)	-	150	-
Clause 8, Table 1, Note 5(Titanium)	-	150	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	0	-
Clause 8, Table 1, Note 6(Boron)	-	300	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	0	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	0	-
Cl. 15, 16(Width )	-	500	-
Cl. 15, 16(Thickness )	-	500	-
Cl. 15, 16(Weight)	-	500	-
Cl 15(Length, Width & Thickness)	-	1500	-

02 Feb, 2028

-
Included w.e.f. 01.01.2026 Exclusion: Clause 13 Y Groove Crackability Test

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

9177306

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

TABLE 1 AND TABLE

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	10000	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	10000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	10000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	10000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	10000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 15, 16(Off Centre of Web)	-	10000	-
Cl. 15, 16(Flange out of square (I beam))	-	10000	-
Cl. 15, 16(Width of flange (I Beam))	-	10000	-
Cl. 15, 16(Depth (I Beam))	-	10000	-
Cl. 15, 16(Mass (Plate))	-	10000	-
Cl. 15, 16(Flange Slope)	-	10000	-
Cl. 15, 16(Web Thickness)	-	10000	-
Cl. 15, 16(Flange Thickness)	-	10000	-
Cl. 15, 16(Out of Square (Flat))	-	10000	-
Cl. 15, 16(Width )	-	10000	-
Cl. 15, 16(Thickness )	-	10000	-
Cl. 15, 16(Sectional Area )	-	10000	-
Cl. 15, 16(Camber (Angle))	-	10000	-
Cl. 15, 16(Out of Square (Angle))	-	10000	-
Cl. 15, 16(Weight)	-	10000	-
Cl. 15, 16(Leg Length Difference (Angle))	-	10000	-
Cl. 15, 16(Leg Length B (Angle))	-	10000	-
Cl. 15, 16(Leg Length A (Angle))	-	10000	-
Cl. 15, 16(Toe Radius R2)	-	10000	-
Cl. 15, 16(Root Radius R1)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 18(Weight)	-	10000	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(By Calculation)	-	10000	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 6(By Calculation)	-	10000	-
Clause 7(IS 2062)	-	10000	-
Clause 11.3(IS 1599)	-	10000	-
Clause 12(IS 1757)	-	10000	-
Clause 15, Table 4(IS 2062)	-	10000	-
16(Tolerance)	-	10000	-
20(Marking)	-	10000	-
20(MARKING)	-	10000	-
8(Micro Alloying elements)	-	10000	-
8(Niobium as Nb)	-	10000	-
8(Vanadium as V)	-	10000	-
8(Titanium as Ti)	-	10000	-
10(Tensile Strength-IS:1608(P1)-22)	-	10000	-
10(Yield Stress-IS:1608(P1)-22)	-	10000	-
10(Elongation on SoA 5.65mm GL)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimension -D)	-	10000	-
15(Dimension -B)	-	10000	-
15(Thickness - t)	-	10000	-
15(Thickness - T)	-	10000	-
15(Flange Slope)	-	10000	-
15(Radius R1)	-	10000	-
15(Radius R2)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimension -D)	-	10000	-
15(Dimension -B)	-	10000	-
15(Thickness - t)	-	10000	-
15(Thickness - T)	-	10000	-
15(Radius R1)	-	10000	-
15(Radius R2)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimensions AxB)	-	10000	-
15(Thickness - t)	-	10000	-
15(Radius -R1)	-	10000	-
15(Radius -R2)	-	10000	-
15(Diameter)	-	10000	-
15(Sectional Area)	-	10000	-
15(Mass per metre)	-	10000	-
15(Mass per metre)	-	10000	-
15(Ovality)	-	10000	-
15(Side Width)	-	10000	-
15(Sectional Area)	-	10000	-
15(Mass per metre)	-	10000	-
15(Out of Square)	-	10000	-
9(Preparation of test sample)	-	10000	-
Clause 8, Table 1, Note 2(Aluminium)	-	10000	-
Clause 8, Table 1, Note 5(Niobium)	-	10000	-
Clause 8, Table 1, Note 5(Titanium)	-	10000	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	10000	-
Clause 8, Table 1, Note 6(Boron)	-	10000	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	10000	-
Clause 7(Freedom from Defect)	-	10000	-
Clause 11.3(Bend Test)	-	10000	-
Clause 12(Impact Test)	-	10000	-
Clause 15, Table 4(Dimension)	-	10000	-
5(General Requirements)	-	10000	-
4(MARKING)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-

30 Mar, 2027

-
Included w.e.f.28.07.2025 Exclusion Cl 13 (Y Groove Cracking Test) Cl 14.1 (Soundness test) Cl 14.2 (Grain Size) Cl 14.2 (Inclusion)

LUCID LABORATORIES PRIVATE LIMITED, HYDERABAD

6121636

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

HOT ROLLED STEEL

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	1000	Nil
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	250	Nil
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	250	Nil
Cl 7(Workmanship)	-	500	Nil
Cl 10.3(UTM)	-	1000	Nil
Cl 11.3(Press)	-	500	Nil
Cl 12(Sudden Load Applied)	-	1150	Nil
Cl 13(Y Groove Cracking Test)	-	0	NA
Cl 18(Weight)	-	100	Nil
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	250	Nil

19 Apr, 2028

-
Except- Y Groove Crackability test (Cl.13) & Other tests (Cl.14)

Standard Testing Laboratory Private Limited

8170106

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	Complete Testing Charges Rs 12000
Cl 7(Workmanship)	-	500	Complete Testing Charges Rs 12000
Cl 10.3(UTM)	-	3000	Complete Testing Charges Rs 12000
Cl 11.3(Press)	-	800	Complete Testing Charges Rs 12000
Cl 12(Sudden Load Applied)	-	2500	Complete Testing Charges Rs 12000
Cl 13(Y Groove Cracking Test)	-	0	Complete Testing Charges Rs 0
Cl 15(Length, Width & Thickness)	-	800	Complete Testing Charges Rs 12000
Cl 18(Weight)	-	200	Complete Testing Charges Rs 12000
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	Complete Testing Charges Rs 12000
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Complete Testing Charges Rs 12000

10 Apr, 2028

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number