BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

269 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12 AND AS PER IS 4736 (UNIFORMITY OF ZINC COATING)	-
12 AND AS PER IS 4736 (MASS OF ZINC COATING)	-
6.2 AND AS PER IS 513 (CARBON)	-
6.2 AND AS PER IS 513 (PHOSPHORUS)	-
6.2 AND AS PER IS 513 (SULPHUR)	-
Cl. 15 (Workmanship)	-
Cl. 8, 9 Table 3,4 & 5 (Mass of Tube)	-
Cl. 14.3 (Flattening test (Over 50 mm NB))	-
Cl. 14.2 (Bend Test (uto and including 50 mm NB))	-
Cl. 14.1.1 (Elongation)	-
Cl. 14.1 (Tensile Strength)	-

-
" 3m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding excl bend test, joint (thread checking),hydrostatic test & Leak proof test (at manufacturer’s works).

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.4 (Burners)	-

-
`

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-7 (Marking)	-
Cl-13 (Strength of Assembly)	-

-
" 2 Nos. Complete for IPX0 only.

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3.1.1, 3.1.2 (Minimum Thickness of Sheet)	-
Cl-8 (Workmanship and Finish)	-

-
" 2 nos Excluding Excl. Tests for Non-stick Coating and tests for lunch boxes cl. 8.6.,no chemical tests

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.5 (Oxidation Induction Time)	-

-
-

IS 2556 : Part 2 (2024)

Vitreous China Sanitary Appliances âSpecification Part 2 Specific Requirements of Washdown Water Closets (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
As per Clause 3 (General requirements - Chemical Resistance Test as per IS 2556 (Part 1))	-
As per Clause 3 (General requirements - Resistance to Staining and Burning as per IS 2556 (Part 1))	-
Cl-5 (DIMENSIONS AND TOLERANCES)	-
Cl-7 (FINISH)	-

-
-

IS 9873 : Part 3 (2017)

Safety of toys: Part 3 migration of certain elements (Second Revision)

Any material except modelling clay and finger paint

14080/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table 1 (Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 (Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-

-
Any material given in Clause 1 of IS 9873 (Part-1) except modelling clay and finger paint

IS 797 (2023)

COMMON SALT FOR CHEMICAL INDUSTRIES SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Description)	-
Cl-4.2 (Moisture Content)	-
Cl-4.3, Table-1 (i) (Sodium chloride (as NaCl), percent by mass, Min)	-
Cl-4.3, Table-1 (ii) (Matter insoluble in water, percent by mass, Max)	-
Cl-4.3, Table-1 (iii) (Calcium salts (as Ca), percent by mass, Max)	-
Cl-4.3, Table-1 (iv) (Magnesium salts (as Mg), percent by mass, Max)	-
Cl-4.3, Table-1 (v) (Sulphates (as SO4 ), percent by mass, Max)	-
Cl-4.3, Table-1 (vi) (Iron compound (as Fe), ppm, Max)	-
Cl-4.3.1 (Sulphate (as SO4))	-
Cl-4.3.1 (Iron)	-
Cl-4.3.1 (Alkalinity)	-
Cl-4.1 (Description)	-

-
-

IS 15757 (2022)

FOLLOW-UP FORMULA-COMPLEMENTARY FOODS - SPECIFICATION (First Revision of IS 15757)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.8,Table 2 ,Sl No i) (Aerobic plate count)	-
"4.8 Table 2 (ii) " (Coliform count-IS 5401 (Part 1))	-
Clause 4.8,Table 2 ,Sl No iii) (Staphylococcus aureus( Coagulase positive))	-
Clause 4.8,Table 2 ,Sl No iv) (Yeast and mould count)	-
Clause 4.8,Table 2 ,Sl No v) (Salmonella sp.)	-
Clause 4.8,Table 2 ,Sl No vi) (Listeria moncytogenes)	-
Clause 4.8,Table 2 ,Sl No vii) (Bacillus cereus)	-
Clause 4.8,Table 2 ,Sl No viii) (Sulphite reducing clostridia)	-
Clause 4.8,Table 2 ,Sl No ix) (Escherichia coli)	-

-
Microbiology tests complete

IS 17782 (2021)

FORTIFIED RICE KERNELS-SPECIFICATION

Please See Remerk View breakup
Total Man Hours: 11 x 300 =3300/- Total Power consumption: 168 x 9 = 1512/- Total Consumable cost = 290/- Total testing charges = Rs 5102/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-4, 4.7 and 8 (i) Total plate count,)	-
Table-4, 4.7 and 8 (ii) Yeasts and moulds,)	-
Table-4, 4.7 and 8 (iii) Coliform count,)	-

-
complete Microbiological test

IS 17514 (2021)

Reusable Sanitary PadSanitary Napkin Period panties Specification

Rs 8659/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause No. 9.3.1 (Bacterial and Fungal Bioburden)	-
9.3.2 (Test for Common Skin Pathogen -Staphylococcus Aureus)	-
Clasue No. 10 (Anti-Bacterial Activity Value)	-

-
All Microbiological tests except biocompatibility and cyclotoxicity tests

IS 5405 (2019)

Sanitary napkins – Specification (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.3.1 (Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-
Cl7.3.2 (Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-

-
All Microbiology tests except Biocompatibility and cytotoxicity tests

IS 14433 (2022)

INFANT MILK SUBSTITUTES - SPECIFICATION (Second Revision of IS 14433)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5.10,Table 3, Sl No i) (Aerobic plate count)	-
Clause 5.10,Table 3, ,Sl No iii) (Staphylococcus aureus)	-
"5.10 Table 3 (iii)" (Yeast & mould count-IS 5403)	-
1 (Salmonella sp.-IS 5887 (Part 3))	-
CL 5.10, Table 3 (v) (Listeria monocytogenes)	-
CL 5.10, Table 3 (ix) (Enterobacter sakazakii (Cronobacter sp.))	-
CL 5.10, Table 3 (viii) (Enterobacteriaceae)	-
Clause 5.10,Table 3, ,Sl No vii) (Bacillus cereus)	-
Clause 5.10,Table 3, ,Sl No viii) (Sulphitr reducing clostridia)	-

-
Micro tests complete

IS 17945 (2022)

FOOD FOR SPECIAL MEDICAL PURPOSE INTENDED FOR INFANTS ï¿½ SPECIFICATION

Please See Remerk View breakup
Total Man Hours: 38 x 300 =11400/- Total Power consumption: 720 x 9 = 6480/- Total Consumable cost = 3240/- Total testing charges = Rs 21120/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
"5.12 Table 2 (i) " (Aerobic plate count-IS 5402 (Part 1))	-
"5.12 Table 2 (ii)" (Staphylococcuus aureus-IS 5887 (Part 8/Sec-1))	-
"5.12 Table 2 (iii)" (Yeast & mould count-IS 5403)	-
"5.12 Table 2 (iv)" (Salmonella sp.-IS 5887 (Part 3))	-
"5.12 Table 2 (v)" (Listeria monocytogenes-IS 14988 (Part 1))	-
v (Bacillus cereus-IS 5887 (Part 6))	-
"5.12 Table 2 (vii)" (Sulphite reducing clostridia-ISO 15213)	-
"5.12 Table 2 (viii)" (Enterobacteriacae-is 17112(p-1))	-
"5.12 Table 2 (ix)" (Enterobacter Sakazakii(Cronobacter spp.)-ISO 22964)	-
5.16 & 5.16.1.5 (Optional Requirement for ECO MARK Vibrio cholerae & Vibrio parahaemolyticus IS 5887 Part-5)	-

-
Complete Micro tests

IS 17787 (2021)

Medical Textiles Nonwoven Wipes Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 6.1, Table 1, (i) (Length and width, mm)	-
Clause 6.1, Table 1, (ii) (pH)	-
Clause 6.1, Table 1, (iii) (Total viable count, (cfu/g), Max)	-
Clause 6.1, Table 1, (iv) (Pseudomonas aeruginosa)	-
Clause 6.1, Table 1, (v) (Staphylococcus aureus)	-
Clause 6.1, Table 1, (vi) (Candida albicans)	-
Clause 6.1, Table 1, (vii) (E. coli)	-
Clause 6.1, Table 1, (viii) (Anti-bacterial activity (optional), absorption method,)	-
Clause 6.3 (Seal Leakage Test)	-

-
Complete facilities

IS 17786 (2022)

Medical Textiles Underpad Specification

Please See Remerk View breakup
Total Man Hours: 15 x 300 =4500/- Total Power consumption: 221 x 9 = 1989/- Total Consumable cost = 570/- Total testing charges = Rs 7059/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 8.3.1 (Bacterial and Fungal Bioburden)	-
Clause 8.3.2 (Test for Common Skin Pathogen - Staphylococcus Aureus)	-

-
Complete Microbiology Tests except Biocompatibility and cytotoxicity (optional ) requirements

IS 17509 (2021)

Disposable Baby Diaper Specification

7059 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause no. 3 (Material)	-
Clause no. 3.1 (Top Cover / Top Sheet)	-
Clause no. 3.2 (Absorbent Core)	-
Clause no. 3.3 (Outer Protective Barrier or Back Sheet)	-
Clause no. 4 (Fastening & Securing Mechanism)	-
Clause no. 5 (ManufactureWorkmanship and Finish)	-
Clause no.6 (Type and Size: FOR X LARGE)	-
Clause no.6 (Diaper Length)	-
Clause no.6 (Diaper Width)	-
Clause no.6 (Diaper Crotch)	-
Clause no.6 (Absorbent Core Length)	-
Clause no.6 (Absorbent Core Width Back)	-
Clause no.6 (Absorbent Core Length)	-
Clause no.6 (Absorbent Core Width Front)	-
Clause no.6 (Core Cortch)	-
Clause no.7.1 (pH Value)	-
Clause no.7.2 Table-2 (Minimum absorption Capacity (X Large))	-
Clause no.7.2 Table-2 (Rewet under Load (All Sizes))	-
Clause no.7.2 Table-2 (Rate of Absorption (All Sizes))	-
Clause no.7.3 (Hygiene Testing Requirement, Total Viable Count)	-
Clause no.7.3 (Hygiene Testing Requirement, Staphylococcus Aureus)	-
Clause no.7.7 (Anti-Bacterial Activity Value (optional))	-

-
Sample size: 20 Nos. Test facility not available for Cl. 7.5 Phthalate Test and Cl. 7.6 Biodegradability and Compostability (Optional)

IS 710 (2010)

Marine plywood - Specification (Second Revision)

Rs 11200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (DIMENSIONS)	-
6.1 (DIMENSIONS)	-
6.2 (DIMENSIONS)	-
6.3 (DIMENSIONS)	-
6.3 (DIMENSIONS)	-
9.1.1 (MOISTURE CONTENT)	-
9.1.2 , 9.1.2.1 (Glue Adhesion in Dry State)	-
9.1.2 , 9.1.2.2 (Glue Adhesion in Dry State)	-
9.1.3 , 9.1.3.1.1 (Water resistance test)	-
9.1.3 , 9.1.3.1.2 (Water resistance test)	-
9.1.4 (Tensile strength)	-
9.1.5 (Mycological test)	-
9.1.5 , 9.1.3.1.1 (Mycological test)	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-
11.1 (MARKING)	-

-
Quantity Required: 2 Nos of Marine Plywood Sheets

IS 303 (1989)

Plywood for General Purposes -

Rs 4000/- /BWR Grade, Rs.4900/- for MR Grade Rs 4000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Dimensions & Tolerances - Squareness - Annexure C)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
11.4, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
11.2.2 (Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-
11.2.1 (Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-
11.3 (Moisture Content - Part 1 of IS 1734)	-
9 (Workmanship and Finish - Cl.9, 8.3, Annexure C)	-
5.1 (Type - For BB Type)	-

-
Quantity Required: 2 Nos of Full Sheets

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Gross capacity)	-
8.15.2 (Ball Drop Test )	-

-
" 1 No Excluding Excl Temp. Responsive Pressure Relief Device, Chromium over nickel plating, External Coating, Internal Coating and Chemical tests

IS 1328 (1996)

Veneered Decorative Plywood -Specification

Please see remarks View breakup
Rs. 5550/- for MR. Grade & material testing charges as per relevant referred ISs Rs. 6720/- for BWR Grade & material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Dimensions & Tolerances - Width - Cl. 8)	-
11 (Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-

-
Quantity Required: 2 Nos of Full Sheets

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

Rs 11950/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (Types)	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.3 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
8.1 (WORKMANSHIP AND FINISH )	-
10.1.1 (MOISTURE CONTENT)	-
10.1.2, 10.1.2.1 (Table-1) (GLUE ADHESION IN DRY STATE)	-
10.1.2, 10.1.2.2 (GLUE ADHESION IN DRY STATE)	-
10.1.3, 10.1.3.1.1 (Table-1) (RESISTANCE TO WATER TEST)	-
10.1.3, 10.1.3.1.2 (RESISTANCE TO WATER TEST)	-
10.1.4 (RESISTANCE TO WATER TEST)	-
10.1.5 (MYCOLOGICAL TEST )	-
10.1.5, 10.1.5.1 (Table-1) (MYCOLOGICAL TEST )	-
10.1.5.2 (MYCOLOGICAL TEST )	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-
12, 12.1 (MARKING)	-

-
Quantity Required: 2 Nos of Full Sheets

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

Rs.6494.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.6 (Spot test - Annexure L)	-
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
cl. 11.1 (marking - BIS certification marking)	-

-
Quantity Required: 2 Nos of Block Boards

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-6.1 (Dimensions (length))	-
Cl-6.2 (Thickness)	-
Cl-6.3 (Squareness)	-
Cl-8.3 (Edge Straightness)	-
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6 (Workmanship and finish)	-
Cl-9.3 (Moisture Content)	-
Cl-9.4.2 (Glue Adhesion in Dry State- Adhesion of Plies)	-
Cl-9.5.1.1 (Glue Adhesion in Water Resistance - Glue Shear Strength -Average)	-
Cl-9.5.1.2 (Water Resistance Test-Adhesion of plies)	-
Cl-9.6 (Tensile Strength-Along the grain)	-
Cl-9.7 (Mycological Test -Adhesion)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
Cl-9.8, Table-2 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
Cl-9.9, Table-3 (i) a (Wet Bending Strength- Modulus of Elasticity (MOE)- Average)	-
Cl-9.9, Table-3 (i) b (Wet Bending Strength- Modulus of Elasticity (MOE),-Minimum individual)	-
Cl-9.9, Table-3 (ii) a (Wet Bending Strength- Modulus of Rupture (MOR)-Average)	-
Cl-9.9, Table-3 (ii) b (Wet Bending Strength- Modulus of Rupture (MOR), -Minimum individual)	-
Cl-11.1 (Marking)	-
Cl-9.6 (Tensile Strength-Across the grain)	-

-
Quantity Required: 2 Nos of Marine Plywood Sheets Except Formaldehyde content Cl 9.11 and Steady-state Formaldehyde emission (optional test) as per Cl.9.12

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (Classification by appearance)	-
Cl-5.2, Table- 1 (i) (Blister)	-
Cl-5.2, Table- 1 (ii) (Checks)	-
Cl-5.2, Table- 1 (iii) (Discolouration)	-
Cl-7.2.1 (Thickness of veneers)	-
Cl-8.1 (Dimensions -length)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
Cl-5.2, Table- 1 (iv) (Dote)	-
Cl-5.2, Table- 1 (v) (Insect hole)	-
Cl-5.2, Table- 1 (vi) (Joints)	-
Cl-5.2, Table- 1 (vii) (Knots (dead))	-
Cl-5.2, Table- 1 (viii) (Pin knots (dead))	-
Cl-5.2, Table- 1 (ix) (Pin knots (live))	-
Cl-5.2, Table- 1 (x) (Knots (tight))	-
Cl-5.2, Table- 1 (xi) (Patches)	-
Cl-5.2, Table- 1 (xii) (Splits)	-
Cl-5.2, Table- 1 (xiii) (Swirl)	-
Cl-8.2 (Thickness of the plywood boards)	-
Cl.8, 8.3 & Annex C (Edge Squareness)	-
Cl.8, 8.3 & Annex C (Edge Straightness)	-
Cl-9 (WORKMANSHIP AND FINISH)	-
Cl-11.3.1, 11.3.1.1 (Water Resistance Test)	-
Cl-11.3.2 (Mycological Test)	-
Cl-11.4 (Moisture Content)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
Cl-11.5, Table-4, (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
Cl-13 (Marking)	-
Cl-11.6 (Formaldehyde Content Test)	-

-
Quantity Required: 2 Nos of Full Sheets Steady-state Formaldehyde emission (optional test) as per Cl.11.7

IS 14543 (2024)

Packaged Drinking Water Other than Packaged Natural Mineral Water Specification Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.3, Table-1 (vi) (pH)	-
Cl-5.2.1 (Escherichia coli or thermotolerant bacteria)	-
Cl-5.2.2 (Coliform)	-
Cl-5.2.3 (Staphylococcus aureus)	-
Cl-5.2.4 (Sulphite Reducing Anaerobes)	-
Cl-5.2.5 (Pseudomonas Aeruginosa)	-
Cl-5.2.6 (Aerobic Microbial Count @ 37 deg C)	-
Cl-5.2.7 (Yeast and mould)	-
Cl-5.2.8 (Salmonella)	-
Cl-5.2.9 (Vibrio cholera)	-
Cl-5.2.3 (Faecal streptococci)	-
Cl-5.2.8 (shigella)	-
Cl-5.2.9 (V.parahaemolyticus)	-
5.2.6 (Aerobic Microbial Count @ 20 to 22 deg C)	-
Table 3, x) (Uranium)	-
5.4 i) (o,p DDT)	-
5.4 i) (p,p DDT)	-
5.4, i) (o,p DDE)	-
5.4 i) (p,p DDE)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDD)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (alpha-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (Delta-HCH)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (Monocrotophos)	-
5.4 i) (Ethion)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Phorate)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate sulphone)	-
5.4 i) (2,4-D)	-
5.4 i) (Butachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Alachlor)	-
5.4 i) (Atrazine)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Methyl Paraoxon)	-
5.4, i) ("oxygen analogue of Malathion (Malaoxon)")	-
5.4 i) (Malathion)	-
5.4 i) (Aldrin)	-
5.4 i) (Dieldrin)	-
Cl-5.4 (ii) (Total pesticide residue)	-
Cl-5.3, Table-3 (ix) (Polynuclear aromatic hydrocarbons)	-
Cl-5.3, Table-3 (viii) (Polychlorinated biphenyl (PCB))	-
Cl-5.3, Table-3 (vii) (Nickel (as Ni))	-
Cl-5.3, Table-3 (vi) (Chromium (as Cr))	-
Cl-5.3, Table-3 (v) (Lead (as Pb))	-
Cl-5.3, Table-3 (iii) (Arsenic (as As))	-
Cl-5.3, Table-3 (ii) (Cadmium (as Cd))	-
Cl-5.3, Table-3 (i) (Mercury (as Hg))	-
Cl-5.3, Table-2 (xxv) (Bromates (as BrO3 ))	-
Cl-5.3, Table-2 (xxiv) (Borates (as B))	-
Cl-5.3, Table-2 (xxiii) (Antimony (as Sb))	-
Cl-5.3, Table-2 (xxii) (Sulphide)	-
Cl-5.3, Table-2 (xviii) (Residual free chlorine)	-
Cl-5.3, Table-2 (xvii) (Sodium (as Na))	-
Cl-5.3, Table-2 (xvi) (Magnesium (as Mg))	-
Cl-5.3, Table-2 (xv) (Calcium (as Ca))	-
Cl-5.3, Table-2 (xiv) (Alkalinity (as HCO3 ))	-
Cl-5.3, Table-2 (xiii) (Sulphate (as SO4 ))	-
Cl-5.3, Table-2 (xii) (Selenium (as Se))	-
Cl-5.3, Table-2 (xi) (Chloride (as Cl))	-
Cl-5.3, Table-2 (x) (Aluminium (as A1))	-
Cl-5.3, Table-2 (ix) (Silver (as Ag))	-
Cl-5.3, Table-2 (viii) (Zinc (as Zn))	-
Cl-5.3, Table-2 (vii) (Fluoride (as F))	-
Cl-5.3, Table-2 (vi) (Nitrite (as NO2 ))	-
Cl-5.3, Table-2 (v) (Nitrate (as NO3 ))	-
Cl-5.3, Table-2 (iv) (Manganese (as Mn))	-
Cl-5.3, Table-2 (iii) (Iron (as Fe))	-
Cl-5.3, Table-2 (ii) (Copper (as Cu))	-
Cl-5.3, Table-2 (i) (Barium (as Ba))	-
Cl-5.3, Table-1 (v) (Total dissolved solids, mg/l, Max)	-
Cl-5.3, Table-1 (iv) (Turbidity, nephelometric turbidity unit (NTU), Max)	-
Cl-5.3, Table-1 (iii) (Taste)	-
Cl-5.3, Table-1 (ii) (Odour)	-
Cl-5.3, Table-1 (i) (Colour, true colour units, Max)	-
5.3 (Appearance)	-
Cl-5.3, Table-2 (xx) (Mineral oil)	-

-
" 48x500ml; 24x1 ltr; 6x2ltr; 4x5 ltr; 2x20ltr Excluding ex.for radio active residues , CN, MBAS, Phenolic compounds

IS 17630 (2021)

Medical Textiles Bedsheet and Pillow Cover Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

-
-

IS 7933 (2022)

Specification for Flexible Polyurethane Foam for Domestic Mattresses First Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.8, Table 1, i) (Density,)	-
5.4 (Dimensions and Tolerances)	-

-
-

IS 3748 (2022)

Tool Steels - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.1 (Product diameter or thickness ≥ 15 mm)	-

-
-

IS 1536 (2023)

Centrifugally cast (spun) iron pressure pipes for water, gas and sewage ï¿½ Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
"Cl- 11.1,11.2, 11.4 Annex A" (Ring Test (for pipes cast in metal moulds))	-
Cl- 11.3,6.2,11.4 (Brinell Hardness Test)	-
"Cl- 13 to 14, Table 3 to 11" (Sizes, Dimensions & Tolerances)	-
Cl- 15.1 & 15.2 (Coating)	-

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

No Record Found