BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

278 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

271

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.24(Annexure E) (on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-
Cl.23 (There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-

-
-

272

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
4 (Description)	-
5.6 (Moisture)	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Milk fat)	-
5.6 (Insolubility index)	-
5.6 (Milk fat)	-
5.6 (Total ash (on dry basis))	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Scorched particles)	-
5.6 (Bacterial count)	-
5.6 (Coliform count )	-
5.6 (Escherichia coli)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Salmonella)	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Listeria monocytogenes)	-

-
" 2x500g

273

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

Please see remarks View breakup
Rs. 7800.00 (Excluding Testing Charges for Material Test) Rs. 3600.00 (Testing Charges for Material Test)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 and Table 1 (DIMENSIONS OF PIPES - outside diameters)	-
5 and Table 1 (DIMENSIONS OF PIPES - wall thickness shall)	-
7.2 (Reversion Test)	-

-
" 5m pc " Excluding excl hydraulic characteristics, Susceptibility to env stress cracking test, tensile test and Chem (material) test facility not available.

274

IS 7224 (2006)

Iodized salt, vacuum evaporated iodized salt and refined iodized salt - Specification (Second Revision)

Iodized salt, vacuum evaporated iodized salt & refined

Rs7440/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Particle Size)	-
Clause 4.3 Table 1 (Moisture content)	-
Clause 4.3 Table 1 (water insoluble matter)	-
Clause 4.3 Table 1 (Chloride Content(as Nacl))	-
Clause 4.3 Table 1 (Matter soluble in water other than sodium chloride)	-
Clause 4.3 Table 1 (Calcium (as Ca))	-
Clause 4.3 Table 1 (Magnesium (as mg))	-
Clause 4.3 Table 1 (Sulphate (as SO4 ),)	-
Clause 4.3 Table 1 (Iodine content, a) Manufacturers Level )	-
Clause 4.3 Table 1 (b) Distribution channel including retailer)	-
Clause 4.3 Table 1 (Alkalinity (as Na2CO3),)	-
Clause 4.3 Table 1 (Lead as (Pb))	-
Clause 4.3 Table 1 (Arsenic(as As))	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause 4.3 Table 1 (Lead as (Pb))	-
Clause 4.3 Table 1 (Arsenic(as As))	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause 4.2 (Particle Size)	-
4.4 (Anticaking agents (Potassium Ferrocyanide))	-
Clause no4.1 (Description)	-

-
-

275

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 12 (Sudden Load Applied)	-
Cl 10.3 (UTM)	-
Clause - 5, 8.1 & 8.2 (E650, CARBON +EQUIVELENT )	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause 8, Table 1, Note 2 (Aluminium)	-
Clause 8, Table 1, Note 5 (Niobium)	-
Clause 8, Table 1, Note 5 (Titanium)	-
Clause 8, Table 1, Note 5 (Nb+V+Ti)	-
Clause 8, Table 1, Note 6 (Boron)	-
Clause 8, Table 1, Note 6 (Cr+Ni)	-

-
1 mt" Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding EXCEPT Y GROOVE CRACKABILITY TEST, Facility for preparation of test specimen not available for impact test

276

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

25780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9.4 (Load In Other Direction From Bend)	-
Cl 7.2 (Weight)	-
Cl 5 (Deformations and Surface Characteristics)	-
Cl 6.1 (Length, Width & Thickness)	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Clause 4.2 Note 2, Amendment 1 & 3 (Nb+V+B+Ti)	-
Clause 4.2 Note 3, Amendment 1 & 3 (Cr+Cu+Ni+Mo+P)	-
Clause 4.2, Amendment 3 Note 4 ("In order to ascertain whether sufficient quantities of nitrogen binding elements are present, following formula may be used, where all elements are in ppm. (N−120)< (Al free/10)+((Ti+V)/7)+(Nb/14)")	-
4.2 (Boron (B))	-
4.2 (Niobium (Nb))	-
4.1 (Carbon %)	-
4.1 (Manganese %)	-
4.1 (Phosphorus %)	-
4.1 (Silicon %)	-
4.1 (Sulphur %)	-
4.1 ( Copper %)	-
4.1 ( Aluminium %)	-
4.1 ( Nitrogen%)	-
4.1 ( Nb)	-
4.1 (V)	-
4.1 ( Ti)	-
4.1 (Cr)	-
4.1 (Mo)	-
4.1 (Ni)	-
4.1 (CE)	-
4.1 (Sulphur and phosphorous)	-

-
" 1 mtr x3pcS. Chemical facility is available. Excluding EXCEPT Pullout TEST, Bend and Rebend, 0.2 percent proof stress/ yield stress, Total elongation at maximum force, bar size restricted upto 20 mm for TENSILE TEST

277

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

14700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Operating Test for Pressure Regulating Device)	-
8.4 (Test for Safety Pressure Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.1 (Air Pressure Test)	-
4.1 (Capacity)	-
4.1 (Capacity )	-
8.2 (Proof Pressure Test)	-
8.5 (Bursting Pressure Test)	-
8.1 (Air Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-
8.6.2 (Tests for Removal of Lid under Pressure For inner Lid Cooker)	-
7.1 (WORKMANSHIP AND FINISH)	-
7.2 (WORKMANSHIP AND FINISH)	-
7.3 (WORKMANSHIP AND FINISH)	-
6.4.1.1 (Handles and Knobs)	-
6.4.1 (Handles and Knobs)	-
6.1 (Pressure Regulating Device)	-
6.1.1 (Pressure Regulating Device)	-
6.1.2 (Pressure Regulating Device)	-
6.1.3 (Pressure Regulating Device)	-
6.1.4 (Pressure Regulating Device)	-
6.1.5 (Pressure Regulating Device)	-
6.2 (Safety Relief Device)	-
6.2.1 (Safety Relief Device)	-
6.2.2 (Safety Relief Device)	-

-
" 1 No Excluding Excl Temp. Responsive Pressure Relief Device, Chromium over nickel plating, External Coating, Internal Coating and Chemical tests

278

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

PVC Cables except FR & FRLSH Category

Please see remarks View breakup
Category: 01 Unsheathed cable: a) Single Core, Plain Copper Conductor - Rs.10500 b) Single Core, Tinned Copper Conductor- Rs.10800 c) Single Core, Solid Aluminium Conductor- Rs.10200 d) Single Core, Stranded Aluminium Conductor- Rs.10200 Sheathed Cable: a) Single Core, Plain Copper Conductor- Rs. 17550 b) Single Core, Tinned Copper Conductor - Rs.17850 c) Single Core, Solid Aluminium Conductor- Rs. 17250 d) Single Core, Stranded Aluminium Conductor- Rs.17250 Category: 02 Unsheathed cable: a) Single Core, Plain Copper Conductor- Rs.12150 b) Single Core, Tinned Copper Conductor- Rs.12450 c) Single Core, Solid Aluminium Conductor - Rs.11850 d) Single Core, Stranded Aluminium Conductor - Rs.11850 Sheathed Cable: a) Single Core, Plain Copper Conductor - Rs.18900 b) Single Core, Tinned Copper Conductor - Rs.19200 c) Single Core, Solid Aluminium Conductor - Rs.18600 d) Single Core, Stranded Aluminium Conductor - Rs.18600 Multi core cable: For each additional core, the charges of single core unsheathed cable as per material (copper and aluminium) and as per construction of conductor (solid or stranded, tinned or plain) shall be added

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (Cable code)	-
11.2 (Legibility)	-
11.1 (Durability)	-
11 (Identification)	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.4 (Flammability test- Unaffected portion)	-
10.4 (Flammability test-Burning after flame removal)	-
table 1 e) 3) (IR constant- max. Temp)	-
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-
table 1 e) 3) (Volume Resistivity - Room temp )	-
10.2 (HV (room temperature))	-
10.1 (HV (water immersion))	-
10.1 (HV (water immersion))	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 (Category Code)	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) d) 4) (Cracks Observed)	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) c) 4) (Cracks Observed)	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4) (Colour of Sheath)	-
8.3 (Thickness of Sheath)	-
5.2 (Application )	-
5.3 (Thickness of Insulation)	-
9.1 (Ovality)	-
9 (Overall dimensions)	-
4.2 (Conductor resistance test)	-
4.1 (Wrapping test (for Al))	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Annealing test (for copper))	-
(Cl.16.1) (Cl.19.1) (Conductor- Diameter )	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3) (Assembly of cores )	-
8.1 (Sheath Material )	-
7 (Binder Tape)	-
6.2 (Filler)	-
6.1 (Filler)	-
5.1 (Insulation)	-
4.4 (Joints in Conductor)	-
4.4 (Joints in Conductor)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
8.3 (Minimum thickness of Sheath)	-
8.3 (Avarage thickness of Sheath)	-
5.3 (Minimum thickness of insulation)	-
5.3 (Avarage thickness of insulation)	-

-
" 30 m Excluding Except FR & FRLSH test, Cu Purity test

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List