BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

266 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-

-
8 Kg for Mechanical + Chemical 500 g. Advised Air tight packing with at least 1 month of shelf life. Excluding Complete other than Transverse Strength (Optional)

IS 2112 (2014)

Silver and silver alloys, jewellery/ artefacts - Fineness and marking - Specification (Third Revision)

upto 990 ppt

Rs.1400.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Fineness)	-
5 (Cadmium)	-
5 (Lead)	-

-
10 gm, min.

IS 1741 (2019)

Latex Foam Rubber Products — Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 and Annex F (COMPRESSION SET)	-
12 and Annex E (AGEING)	-
11 and Annex D (FLEXING TEST)	-
11 and Annex D (FLEXING TEST)	-
10.1 and Table 1 & 2 (DIMENSIONS -Thickness)	-
10.1 and Table 1 & 2 (DIMENSIONS -width)	-
10.1 and Table 1 & 2 (DIMENSIONS -Length)	-
9.0 (ODOUR)	-
8.0 (COLOUR)	-
7.3 (MATERIAL AND WORKMANSHIP)	-
7.2 (MATERIAL AND WORKMANSHIP)	-
7.1 (MATERIAL AND WORKMANSHIP)	-
7.1 (MATERIAL AND WORKMANSHIP)	-
5.1.1 (Indentation Hardness index)	-
5.1 (GRADES)	-
4.2 (SIZE AND SHAPE)	-
4.1 (TYPES)	-
Cl 14 (Manganese Content)	-
Cl 14 (Copper content)	-

-
1 Sq.m x 2 pieces. 50x50mm 6 complete pieces with proper edges.

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table-3 iv c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 Table-3 iv b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 Table-3 iv a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 Table-3 iii b (Setting Time Final)	-
7 Table-3 iii a (Setting Time Initial)	-
7 Table-3 ii b (Expansion by Autoclave)	-
7 Table-3 ii a (Expansion by Le Chatelier)	-
7 Table-3 i. (Fineness)	-
6.1 Table-2 viii (Alkali content)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6.1 Table-2 iii. (Insoluble residue)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
6.1 Table-2 i. (Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-

-
8 kg+500g" Excluding Other than Transverse Strength (Optional)

IS 5346 (1994)

Synthetic food colour - Preparations and mixtures - Specification (Second Revision)

Rs. 4100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.5 (Total dye Content)	-
Clause 4.6 Table 1 (Water InsoIuble matter,)	-
Clause 4.6 Table 1 (Lead (as pb) )	-
Clause 4.6 Table 1 (Arsenic(as As))	-
Clause 4.6 Table 1 (Heavy metals)	-

-
Excluding For Synthetic Food Colour Preparations involving Single Dye only (Tartrazine, Carmoisine, Sunset Yellow only)

IS 15644 (2006)

Safety of electric toys

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.0 (Marking and instructions)	-
8.0 (Power Input)	-
9.0 (Heating and abnormal operation)	-
10.0 (Electrical strength at operating temperature)	-
11.1 (Moisture resistance)	-
11.2 (Resistant to humidity)	-
12.0 (Electric strength at room temperature)	-
13.0 (Mechanical strength)	-
14.1 (Construction)	-
14.2 (Construction)	-
14.3 (Construction)	-
14.4 (Construction)	-
14.5 (Construction)	-
14.6 (Construction)	-
14.7 (Construction)	-
14.8 (Construction)	-
14.9 (Construction)	-
19.2.1 (Glow wire test IEC 60695-2-11)	-

-
5 nos Excluding Excluding wheeled ride-on toys, Toys incorporating lasers and light-emitting diodes (Annex E)

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

Rs.225/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Freedom from defects)	-
7.0 (Dimension and Tolerances)	-
9.1 (Tensile Strength)	-

-
" 1 m Excluding Excl Wrapping test. Chemical facility not available

IS 7138 (1973)

Specification for steel tubes for furniture purposes

RS/-300 Chemical View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1(Table 1) (WALL THICKNESS)	-
5 (WORKMANSHIP)	-
7 (STRAIGHTNESS)	-
8 (LENGTHS)	-
9.1 (Tensile Test)	-
9.2 (Bend test)	-
4 (DIMENSIONS)	-

-
" 3 m t. + 25g " Excluding Excl bend test and chemical tests

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

1500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (Freedom from defects)	-
Table-2 (Tensile Strength)	-
Table-2 (Thickness)	-
Table-2 (Elongation)	-

-
"0.5 sq m " Excluding except material test,Cupping test, hardness test

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
7.0 (Dimension and Tolerances)	-
9.1 Table-2 (Tensile Strength)	-
9.1 Table-2 (Elongation)	-
9.2 (Vickers Hardness)	-

-
1 m . Excluding except chemical tests (Tensile test Facility available till 20mm only)

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

Please see remarks. View breakup
Rs. 7370/- for Un-galvanized WT & HFS, For galvanized tubes Rs. 1945/- extra, Rs. 8060/- for CDS & CEW Material testing charges as per relevant referred ISs to be levied additionally

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Workmanship)	-
19.1.1, 24.1.1, 28.1.1, 33.1.1 (Dimensions- Outside Dia)	-
19.1.2, 24.1.2, 28.1.2, 33.1.2 (Dimensions- Thickness)	-
11.1 (Surface Protection)	-
13.1.3 (Tensile Strength)	-
13.1.1 (Yield Stress)	-
13.1.2 (Elongation)	-
13.2 (Flattening Test)	-
13.3 (Bend Test (Strip))	-
13.5 (Drift Expansion Test)	-
13.6 (Crush Test)	-
19.1.3 (Height of Internal Fin)	-
4.1 (Sulphur-Percentage by mass)	-
4.1 (Phosphorus-Percentage by mass)	-
4.0 (a) (Carbon as C - IS:8811)	-
4.0 (b) (Manganese as Mn - IS:8811)	-
4.0 (c) (Micro Alloying elements (Nb+V+Ti))	-
4.0 (f) (Nitrogen content)	-

-
" One pc " Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding Excl. Bend test. Prepared test piece needed for Tensile test

IS 3196 : Part 1 (2013)

Welded low carbon steel cylinders exceeding 5 litres water capacity for low pressure liquefiable gases: Part 1 cylinders for liquefied petroleum gases (Lpg) - Specification (Sixth Revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
20 (Marking)	-
9 (Valve Protection)	-
10 (Foot Ring)	-
14 (Bung)	-
14 (Water Capacity)	-
15 (Hydrostatic Test)	-
16 (Pneumatic Leakage Test)	-
17 (Burst Test under Hydraulic Pressure)	-
18 (Parent Metal Longitudinal Tensile Strength)	-
18 (Parent Metal Circumferential Tensile Strength)	-
18 (Weld Metal Tensile Strength)	-
18 (Root Bend Test)	-
18 (Face Bend Test)	-
18 (Macro Examination)	-
18 (Minimum Thickness Test)	-
21 (Colour Identification)	-
23.2 (Protective Coatings)	-
10.0 (Handle)	-

-
" 2 nos +3 nos. for fatigue " Excluding Except Material test & Radiographic test all tests are available and prepared test piece is needed for acceptance test

IS 5531 (2014)

Cast iron specials for asbestos cement pressure pipes for water and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5 (WALL THICKNESS AND CLASSIFICATION)	-
Cl. 6.3 (Brinell Hardness Test)	-
Cl. 7 (HYDROSTATIC TEST)	-
Cl. 8 (SIZES)	-
Cl. 10.1 (Thickness)	-
Cl. 12 (COATING)	-

-
Excluding Hydrostatic test, material tests. Facility for preparation of test specimen not available.

IS 10 : Part 3 (1974)

Plywood Tea-Chests: Part-3 Battens

Rs 600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions)	-
4.2 (Tolerances)	-
6.0 (FINISHING)	-

-
" 12 nos. - 1set " Excluding Except SPECIES OF TIMBER, Requirements, Comression parallel to Grains, Static Bending

IS 2980 (1999)

Non - Pressure stoves - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (MATERIAL)	-
5.1 (construction of the stoves)	-
5.2 (Fuel Leakage)	-
5.3 (Fuel container)	-
5.4 (Knob fro winding)	-
5.5 (Various components of stoves of one make)	-
5.6 (Perforated Sleeves)	-
5.8 (For Single-Wick and Multi-Wick Stoves)	-
6.2 (Thermal Efficiency Test)	-
6.3 (Combustion Efficiency)	-
6.4 (Flame Stability Test)	-
6.5 (Fuel Creep)	-
6.6 (Surface Temperature Test)	-
6.7 (Fuel Temperature Test)	-
6.8 (Flame Flash-Back Test)	-
6.9 (Stability Test)	-
6.1 (Ability to Withstand Heavy Loads)	-

-
" 2 No. + 50 gm " Excluding except chemical tests

IS 10 : Part 2 (2013)

Plywood tea - Chests - Specification: Part 2 plywood (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (SIZES)	-
7.2 (Thickness)	-
8.0 (FINISH)	-
9.2 (Moisture Content)	-

-
" (4+2) - 1 set Excluding Except species identification, REQUIREMENTS, Cyclic Test, Material and Tests on material

IS 5135 : Part 2 (1994)

Specification for hand rotary duster: Part 2 shoulder mounted type (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Capacity)	-
8.0 (WORKMANSHIP AND FINISH)	-

-
" 1 no. " Excluding 1.Test for Agitation 2.Test for Strap and Its Assembly 3.PERFORMANCE REQUIREMENTS 4. raw material tests

IS 10 : Part 1 (1990)

Plywood tea - Chests - Specification: Part 1 general (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (DESIGN OF TEA-CHEST)	-
6.1 (Sizes)	-
7.1 (Maximum Permirsible Mass of Empty Tea-Chest)	-
7.2 (Certificate of Tare)	-

-
" 3 Boxes Excluding Except End Compression Test , Corner Drop Test, Material and Tests on material

IS 10 : Part 4 (1989)

Plywood tea - Chests - specification: Part 4 metal fittings

Rs 225/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIAL)	-
4.1 (Thickness)	-
4.2 (Width)	-
4.3 (Length)	-
4.3.1, 4.3.3, Table 1 (Size of Tea-chest)	-
4.3.1, 4.3.3, Table 1 (Length, corners)	-
4.3.1, 4.3.3, Table 1 (Length, top and bottom)	-
4.3.4 (tea-chest ofsize 380 mm X 685 mm x 845 mm, For corners)	-
4.3.4 (tea-chest ofsize 380 mm X 685 mm x 845 mm, For top and bottom)	-

-
" 12 nos. - 1 set

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

Please see remarks View breakup
Rs.6900/- Excluding Tensile Strain Hardening component, Bake bardending index & surface finish test and Rs.1004/- for each of the elements other than carbon, sulphur, phosphorus and manganese.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 10 (Length, Width & Thickness)	-
Cl 9 (Workmanship)	-

-
" 1m Excluding Tensile Strain Hardening Component (n-value), surface finish & Chemical facility not available

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Rs.8850/- Excluding Tensile Strain Hardening component View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Mechanical and Physical Properties)	-
Cl 8 (UTM)	-
Cl 10 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
7.0 (ALUMINIUM)	-
7.0 (MICRO ALLOYS)	-
7.0 (NITROGEN)	-
7.0 (SILICON)	-
7.0 (MANGANESE)	-
7.0 (PHOSPHORUS)	-
7.0 (SULPHUR)	-
7.0 (CARBON)	-

-
" 1m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding 1.Cupping test, 2.Bend Test, 3. surface finish, 4. Tensile Strain Hardening Component (n-value) 5.Bake Hardening Index – (BH), 6. plastic strain ratio not available

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Dimension and Tolerances)	-
4.3.1 (Nominal Thickness)	-
4.3.2 (Handle wire diameter)	-
4.4.1 (Body)	-
4.4.2 (Sides)	-
4.4.3 (Top and Bottom)	-
4.4.4 (Top and Bottom embossing)	-
4.4.5 (Handle)	-
4.4.6 (Closure)	-
4.4.7 (Supply condition)	-
4.4.8 (Internal Finish)	-
4.4.9 (External Treatment)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-
4.1 (Capacity)	-

-
" 2 nos. Excluding except raw material tests

IS 10577 (1982)

Specification for lancing pipes

Rs.3650/- excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 .1 Table 1,2,3 (Dimensions)	-
6 .1 Table 1,2,3 ( 1) Outside diameter )	-
6 .1 Table 1,2,3 (2) Thickness,mm)	-
7 Table 1,2,3 ( 2)Mass,kg/m)	-
6 .1 Table 4 (3)Socket dimension)	-
6 .1 Table 4 ( i)OD,mm)	-
6 .1 Table 4 ( ii)Length.mm)	-
14.1 (Workmanship)	-
18.0 (Coating )	-
13.4.1 ( 1)Drift Expanding Test)	-
13.2 (i)Tensile strength,, Mpa Min)	-
13.2 (ii)Elongation,% Min)	-

-
" 2 mtl. Excluding excl joints, bend test, Hydraulic test & Taper Screw Plug Test and tensile test

IS 5135 : Part 1 (1994)

Specification for hand - Rotary duster: Part 1 belly - Mounted type (Second Revision)

Testing charges for the product are Rs 7600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Capacity)	-
8.0 (WORKMANSHIP AND FINISH)	-

-
" 1 set Excluding 1.Test for Agitation 2.Test for Strap and Its Assembly 3.PERFORMANCE REQUIREMENTS 4. raw material tests

IS 1711 (1984)

Specification for self - Closing taps for water supply purposes

Rs 600/-,excl endurance test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3 (NOMINAL SIZE)	-
Cl. 5 (MANUFACTURE AND WORKMANSHIP)	-
Cl. 6.2 (Body and Gland)	-
Cl. 6.3 (Valve and Spindle)	-
Cl. 6.4 (Screw Threads )	-
Cl. 6.5 (Washers)	-
Cl. 7 (FINISH)	-

-
" 5 NOS.+PIECE FOR COATING Excluding Except test for flow of water at the outlet end (cl 8.2) and endurance test

IS 2326 (1987)

Automatic Flushing Cisterns for Urinals (Other than Plastic Cisterns)

1275 incl endu test + material as per ISS View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0 (NOMINAL SIZE)	-
4.2 (Cistern )	-
4.3 (Depth of Cistern Body)	-
4.4 (Siphonic Apparatus)	-
4.5 (Lid and Cover)	-
4.6 (Feeding Device -)	-
5.0 (FINISH)	-
6.1 (a) (Urinal Delivering capacity)	-
6.1 (b) (Flushing)	-
6.1 (c) (Discharge)	-

-
" 1 NO. Excluding except for material test,external threading, finish and endurance test

IS 2039 : Part 1 to 3 (1991)

Steel tubes for bicycle and cycle rickshaws - Specification (Second Revision)

Rs.4320.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1 (Workmanship)	-
Cl. 6.2 (Fin Height)	-
Cl. 8.1 (Tensile Strength)	-
Cl. 8.1 (Yield Strength)	-
Cl. 8.1 (Elongation)	-
Cl. 8.2 (Drift Expansion Test- IS 2335)	-
Cl. 8.3 (Flattening Test-IS 2338)	-
Cl. 9 (Diameter)	-
Cl. 9 (Thickness)	-
Cl. 3.2.1, Table 4 (Yield Stress)	-
Cl. 3.2.1, Table 4 (UTS)	-
Cl. 3.2.1, Table 4 (Elongation)	-
Cl. 3.2.2, Table 2 (Drift Expansion Test- IS 2335)	-
Cl. 3.2.3, Table 3 (Flattening Test-IS 2338)	-
Cl. 4.2.1 (Diameter)	-
Cl. 4.2.2 (Thickness)	-
Cl. 4.2.3 (Length)	-
Cl. 4.2.1, Table 7 (Yield Stress)	-
Cl. 4.2.1, Table 7 (UTS)	-
Cl. 4.2.2, Table 8 (Drift Expansion Test- IS 2335)	-
Cl. 4.2.3, Table 9 (Flattening Test-IS 2338)	-
Cl. 5.2.1, Table 10 (Diameter)	-
Cl. 5.2.2 (Mean Thickness)	-
Cl. 5.2.3, Table 6 (Length)	-

-
1.5mx2 Excluding except drift expansion test, Tensile Test ,chemical test

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3 (Manufacturing )	-
Cl 7 (Workmanship)	-
Cl 8 (Manufacturing )	-
Cl 10 (Diameter)	-
Cl 12.2 (UTM)	-
Cl 12.3 (Torsion)	-
Cl 12.5 (Wrap)	-
Cl 12.6 (Adhesion )	-

-
" 5 m . Excluding except tensile test, torsion test, reverse bend test, adhesion test,raw material tests

IS 10840 (1994)

Blow moulded hdpe containers for packing of vanaspati - Specification (Second Revision)

1425 + raw material as per IS:10146 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Manufacture)	-
4.3 (Capacity)	-
4.4 (Mass)	-
4.5 (Shape and Dimensions)	-
4.6 (Wall Thickness)	-
4.7.1 (Closure Leakage test)	-
4.7.2 (Drop impact test)	-
4.7.3 (Stacking test)	-
4.7.4 (Handle Pull Test)	-
4.7.5 (Ink adhesion for printed containers)	-
4.7.6 (Product Resistance of printed containers)	-
4.7.7 (Migration test)	-

-
" 12 + 12 Nos. Excluding Excl material tests(metal content can be tested as per iS 1699)

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6.2 (TRANSPARANCY)	-
4.6.3 (LEAKAGE TEST)	-
4.6.4 (DROP TEST)	-
4.6.5 (MIGRATION TEST)	-
4.6.6 (PORTABILITY TEST)	-
4.0 (chem) (MATERIAL)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- c. Air pressure leakage)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- b. Vibration leakage)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- a. Closure leakage )	-
4.4 , clause 5 of IS:2798:1998 (Brimful capacity in ml)	-
4.5, IS:2798:1998 (Wall thickness- Bottom, in mm)	-
4.5, IS:2798:1998 (Wall thickness- Middle , in mm)	-
4.5, IS:2798:1998 (Wall thickness- Top , in mm )	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i) (Barium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii) (Cobalt)	-

-
" 5L and above (20L Jar also)- 8 filled + 10 empty+30 Caps; 500ml and above Bottles: 12 filled+24 empty+40 Caps; Below 500ml Bottles: 12 filled+30 empty+40 Caps " Except Material Tests.

First
Prev
2
3
4
5
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List