BIS - LIMS (Laboratory Information Management System)

The Synthetic and Art Silk Mills' Research Association

SASMIRA, SASMIRA Marg, WORLI,, MUMBAI, Mumbai, Maharashtra, 400030

9850251038 mmti@sasmira.org

Scope List

Reset

27 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 7056 (2024)

Textiles ï¿½ Cotton Towelling and Towels ï¿½ Specification (Second revison)

12275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1, Table-1(Count of Yarn, Ne)	-	1200	-
Cl-3.1, Table-1(Threads per dm, Min)	-	600	-
Cl-3.1, Table-1(Mass, Min)	-	400	-
Cl-3.1, Table-1(Terry Ratio, Min)	-	375	-
Cl-3.1, Table-2(Count of Yarn, Ne)	-	0	repeat
Cl-3.1, Table-2(Threads per dm Min)	-	0	repeat
Cl-3.1, Table-2(Mass, Min)	-	0	repeat
Cl-3.2.1, Table-3 (i)(Identification of material)	-	500	-
Cl-3.2.1, Table-3 (ii)(Breaking load on 5.0 cm × 20 cm strips Min)	-	1000	-
Cl-3.2.1, Table-3 (iii)(Scouring loss, percent, Max)	-	600	-
Cl-3.2.1, Table-3 (iv)(Dimensional change, percent, Max)	-	500	-
Cl-3.2.1, Table-3 (v)(pH value)	-	350	-
Cl-3.2.1, Table-3 (vii), a(Minimum Colour Fastness Rating to Light)	-	1200	-
Cl-3.2.1, Table-3 (vi)(Wettability, Max)	-	500	-
Cl-3.2.1, Table-3 (vii), b(Minimum Colour Fastness Rating to Washing)	-	400	-
Cl-3.2.1, Table-3 (vii), c(Minimum Colour Fastness Rating to Hypochlorite)	-	350	-
Cl-3.2.2(Whiteness index)	-	1500	-
Cl-3.3(Freedom from Defects)	-	1000	-
Cl-3.4, Table-4(Minimum Dimensions-Width)	-	200	-
Cl-3.4, Table-4(Minimum Dimensions-Length)	-	200	-
Cl-3.5, Table-4(Maximum depth of plain heading)	-	200	-
Cl-3.6 (a)(Cotton sewing thread)	-	400	-
Cl-3.6 (b)(Polyester sewing thread)	-	0	repeat
Cl-3.7(Transverse Ends or End Hems)	-	200	-
Cl-3.8(Side Edges)	-	200	-
Cl-3.9(Stitching)	-	200	-
Cl-5(Marking)	-	200	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 18739 (2024)

Textiles Bedsheets Pillow cover and Blanket Cover Specification

58400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1, Table-1(Fibre content)	-	500	To be charged for bed sheet
3.1, Table-1(Count of Yarn-Warp)	-	400	To be charged for bed sheet
3.1, Table-1(Count of Yarn-Weft)	-	400	To be charged for bed sheet
3.1, Table-1(Weave)	-	400	To be charged for bed sheet
3.1, Table-1(Ends/cm)	-	200	To be charged for bed sheet
3.1, Table-1(Picks/cm)	-	200	To be charged for bed sheet
3.1, Table-1(Mass g/m2, Min)	-	400	To be charged for bed sheet
3.1, Table-1, (iii)(Tolerance)	-	0	To be charged for bed sheet
3.1, Table-2(Breaking Load on 5 cm × 20 cm Strip (Ravelled Strip Method)-Warpway)	-	500	To be charged for bed sheet
3.1, Table-2(Breaking Load on 5 cm × 20 cm Strip (Ravelled Strip Method)-Weftway)	-	500	To be charged for bed sheet
3.1, Table-2(Tear Strength,-Warpway)	-	500	To be charged for bed sheet
3.1, Table-2(Tear Strength,-Weftway)	-	500	To be charged for bed sheet
3.1, Table-2(Fabric Skew, Percent, Max)	-	400	To be charged for bed sheet
3.1, Table-2(Fabric Bow, Percent, Max)	-	400	To be charged for bed sheet
3.1, Table-2("Dimensional Change, Percent,- Warpway/Weftway")	-	1000	To be charged for bed sheet
3.1, Table-2(Scouring Loss Percent, Max)	-	600	To be charged for bed sheet
3.1, Table-2(pH Value)	-	350	To be charged for bed sheet
3.1, Table-2(Resistance to Pilling, For 1 000 Cycles, Min)	-	400	To be charged for bed sheet
3.1, Table-3 (i)("Light: a) Warp direction b) Weft direction")	-	1200	To be charged for bed sheet
3.1, Table-3 (ii)("Washing: a) Change in colour b) Staining of adjacent fabrics")	-	400	To be charged for bed sheet
3.1, Table-3 (iii)(Bleaching: Hypochlorite)	-	350	To be charged for bed sheet
3.1, Table-3 (iv)("Rubbing: a) Dry b) Wet")	-	250	To be charged for bed sheet
3.1, Table-3 (v)("Perspiration, acidic and alkaline: a) Change in colour b) Staining of adjacent fabrics")	-	400	To be charged for bed sheet
3.2(Fabric Content)	-	500	To be charged for bed sheet
3.3(Freedom from Defects)	-	800	To be charged for bed sheet
3.4(Sewing Thread)	-	600	To be charged for bed sheet
3.5(Hems)	-	400	To be charged for bed sheet
3.6(Sewing)	-	400	To be charged for bed sheet
3.7, Table-4(- Size)	-	400	To be charged for bed sheet
3.7, Table-4(Width,cm)	-	400	To be charged for bed sheet
3.7, Table-4(Length, cm)	-	400	To be charged for bed sheet
Cl-3.8(Soil Release Efficiency)	-	11500	To be charged for bed sheet
Cl-3.9(Antimicrobial Activity)	-	2800	To be charged for bed sheet
Cl-3.10(Whiteness Index)	-	750	To be charged for bed sheet
3.1, Table-1(Fibre content)	-	500	To be charged for pillow cover
3.1, Table-1(Count of Yarn-Warp)	-	400	To be charged for pillow cover
3.1, Table-1(Count of Yarn-Weft)	-	400	To be charged for pillow cover
3.1, Table-1(Weave)	-	400	To be charged for pillow cover
3.1, Table-1(Ends/cm)	-	200	To be charged for pillow cover
3.1, Table-1(Picks/cm)	-	200	To be charged for pillow cover
3.1, Table-1(Mass g/m2, Min)	-	400	To be charged for pillow cover
3.1, Table-1, (iii)(Tolerance)	-	0	To be charged for pillow cover
3.1, Table-2(Breaking Load on 5 cm × 20 cm Strip (Ravelled Strip Method)-Warpway)	-	500	To be charged for pillow cover
3.1, Table-2(Breaking Load on 5 cm × 20 cm Strip (Ravelled Strip Method)-Weftway)	-	500	To be charged for pillow cover
3.1, Table-2(Tear Strength,-Warpway)	-	500	To be charged for pillow cover
3.1, Table-2(Tear Strength,-Weftway)	-	500	To be charged for pillow cover
3.1, Table-2(Fabric Skew, Percent, Max)	-	400	To be charged for pillow cover
3.1, Table-2(Fabric Bow, Percent, Max)	-	400	To be charged for pillow cover
3.1, Table-2("Dimensional Change, Percent,- Warpway/Weftway")	-	500	To be charged for pillow cover
3.1, Table-2(Scouring Loss Percent, Max)	-	600	To be charged for pillow cover
3.1, Table-2(pH Value)	-	350	To be charged for pillow cover
3.1, Table-2(Resistance to Pilling, For 1 000 Cycles, Min)	-	400	To be charged for pillow cover
3.1, Table-3 (i)("Light: a) Warp direction b) Weft direction")	-	1200	To be charged for pillow cover
3.1, Table-3 (ii)("Washing: a) Change in colour b) Staining of adjacent fabrics")	-	400	To be charged for pillow cover
3.1, Table-3 (iii)(Bleaching: Hypochlorite)	-	350	To be charged for pillow cover
3.1, Table-3 (iv)("Rubbing: a) Dry b) Wet")	-	250	To be charged for pillow cover
3.1, Table-3 (v)("Perspiration, acidic and alkaline: a) Change in colour b) Staining of adjacent fabrics")	-	400	To be charged for pillow cover
3.2(Fabric Content)	-	500	To be charged for pillow cover
3.3(Freedom from Defects)	-	800	To be charged for pillow cover
3.4(Sewing Thread)	-	600	To be charged for pillow cover
3.5(Hems)	-	400	To be charged for pillow cover
3.6(Sewing)	-	400	To be charged for pillow cover
3.7, Table-4(- Size)	-	400	To be charged for pillow cover
3.7, Table-4(Width,cm)	-	400	To be charged for pillow cover
3.7, Table-4(Length, cm)	-	400	To be charged for pillow cover
Cl-3.8(Soil Release Efficiency)	-	11500	To be charged for pillow cover
Cl-3.9(Antimicrobial Activity)	-	2800	To be charged for pillow cover
Cl-3.10(Whiteness Index)	-	750	To be charged for pillow cover

Complete

14 Dec, 2023

14 Dec, 2026

IS 18482 (2023)

Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification

30700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Sack Type)	-	400	-
5.2.1(Fabric)	-	400	-
5.2.2(Linear density of tapes)	-	400	-
5.2.4(Unlaminated fabric mass)	-	400	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	400	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	400	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	600	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	400	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	400	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	600	-
5.4.1(Sack)	-	400	-
5.4.1.1(Centre seam)	-	400	-
5.4.1.2(Bottom seam)	-	400	-
5.4.2(Sack)	-	1200	length, width, gusset, overlap width, bottom fold, dotted line over bottom fold
5.4.3(Sack)	-	200	-
5.4.5(Liner)	-	200	-
6.1.1, Table 1(Inside length)	-	200	-
6.1.1, Table 1(Inside width)	-	200	-
6.1.1, Table 1(Gusset width)	-	200	-
6.1.1, Table 1(Warp per dm)	-	200	-
6.1.1, Table 1(Weft per dm)	-	200	-
6.1.1, Table 1(Mass of laminated fabric)	-	400	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	1000	-
6.2, Table 1(Average breaking strength - Widthwise)	-	1000	-
6.2, Table 1(Breaking strength of bottom seam)	-	1000	-
6.2, Table 1(Breaking strength of centre seam)	-	1000	-
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	0	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	13000	Exposure charges + breaking charges. Total exposure charges Rs. 12000 for 192 hours + Rs 1000 breaking charges
6.3(Average breaking strength - Widthwise after UV exposure)	-	1000	-
6.4(Drop Impact Testing of Filled Sacks)	-	1000	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	100	-
Clause 6.2.2(Stitch strength)	-	1000	-
Clause 6.2.2(Weld seam strength)	-	1000	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	100	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 6.5 Table 1 viii(Ash content)	-	900	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

21050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	2500	Inclusive of FTIR analysis for identifciation
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	400	-
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	400	-
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	200	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	200	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	1000	-
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1000	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	0	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	950	-
5.3(Lamination)	-	400	-
5.4(Sack Fabrication)	-	1000	-
5.5(Capacity)	-	400	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	0	-
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	0	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	0	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	0	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	0	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.4(UV Resistance Test)	-	12000	-
7(PRINTING, PACKAGING AND MARKING)	-	400	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

27600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	400	-
5.2 Table 1(Dimensions)	-	400	-
5.2 Table 1(Dimensions)	-	400	-
5.2 Table 1(Dimensions)	-	400	-
5.2 Table 1(Dimensions)	-	400	-
5.2 Table 1(Ends per dm)	-	200	-
5.2 Table 1(Picks per dm)	-	200	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	400	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	500	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	500	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1000	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	included with breaking strength
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	included with breaking strength
5.2 Table 1(Drop impact strength)	-	1000	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	900	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	900	-
4.6(Capacity)	-	400	-
4.3.1(Bottom Seam)	-	4400	Inclusive of Identification, FTIR analysis, if required, breaking strength of stitching thread, dimension of bottom seam
4.3(Sacks)	-	1600	dimensions of half gusset, fold length, length, width
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	1000	-
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	12000	-
4.2(Linear Density)	-	200	-
4.2(Width of tape)	-	400	-
4.6(Capacity)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3(Sacks)	-	0	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	0	-
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	0	-
4.2(Linear Density)	-	0	-
4.2(Width of tape)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	400	-
4.1.2(Sack Width)	-	400	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	400	-
4.1.4(Patch Length)	-	400	-
4.1.5(Patch Height)	-	400	-
4.1.6(Length of Valve)	-	400	-
4.1.7(Width of Valve Sleeve)	-	400	-
4.1.8(Length of Valve Sleeve)	-	400	-
5.1(Raw Material)	-	3500	-
5.2(Fabric)	-	700	-
5.2(Tape density and width)	-	800	-
5.4(Lamination for PP)	-	4500	-
5.4(Lamination for LDPE)	-	500	-
6.1(Mass of Bale)	-	400	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	1000	-
6.2.2(Weld Strength of Top and Bottom Closures)	-	1000	-
6.3(Drop Impact Testing of Filled Sacks)	-	1000	-
6.4(Ash Content)	-	900	-
6.5(Air Permeability)	-	0	Test not feasible
8(Atomspheric Conditions for Conditioning and Testing)	-	0	The test requires only conditioning of samples
4.1.1(Sack Length)	-	0	-
4.1.2(Sack Width)	-	0	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	0	-
4.1.4(Patch Length)	-	0	-
4.1.5(Patch Height)	-	0	-
4.1.6(Length of Valve)	-	0	-
4.1.7(Width of Valve Sleeve)	-	0	-
4.1.8(Length of Valve Sleeve)	-	0	-
5.1(Raw Material)	-	0	-
5.2(Fabric)	-	0	-
5.2(Tape density and width)	-	0	-
5.4(Lamination for PP)	-	0	-
5.4(Lamination for LDPE)	-	0	-
6.1(Mass of Bale)	-	0	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	0	-
6.2.2(Weld Strength of Top and Bottom Closures)	-	0	-
6.3(Drop Impact Testing of Filled Sacks)	-	0	-
6.4(Ash Content)	-	0	-
8(Atomspheric Conditions for Conditioning and Testing)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

27600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.6(Drop Impact Test)	-	0	-
4.1(Raw Meterial)	-	2500	-
4.2("Fabric a) Width of Tape")	-	200	-
4.2("Fabric b) Linear Density")	-	400	-
4.2("Fabric c) Mesh")	-	200	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	200	-
4.3(Sacks)	-	800	-
4.4.1(Loose Liner)	-	400	-
4.4.1(Thickness of Linear)	-	200	-
4.4.2(Visual Observation)	-	200	-
4.4.3(Bottom Seam of Loose Liner)	-	200	-
4.5(Mass of The Lamination)	-	300	-
4.5(Laminated Fabric)	-	300	-
4.5(Lamination Over Hang of the fabric after trimming)	-	300	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	200	-
4.6.1(Depth of the Stitch( Double fold))	-	200	-
4.6.1(No.of Stitches/dm)	-	200	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	500	-
4.6.2(Breaking Load for UV Stabilized sack)	-	1000	-
4.7(Mouth of the Sack)	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	200	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	500	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	900	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	900	-
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	1000	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.5.3(Mass of Bale)	-	500	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	13000	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
5.6(Drop Impact Test)	-	0	-
4.1(Raw Meterial)	-	0	-
4.2("Fabric a) Width of Tape")	-	0	-
4.2("Fabric b) Linear Density")	-	0	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	0	-
4.3(Sacks)	-	0	-
4.4.1(Loose Liner)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.2(Visual Observation)	-	0	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.5(Laminated Fabric)	-	0	-
4.5(Lamination Over Hang of the fabric after trimming)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
4.7(Mouth of the Sack)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	0	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.5.3(Mass of Bale)	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	0	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
5.6(Drop Impact Test)	-	0	-
4.1(Raw Meterial)	-	0	-
4.2("Fabric a) Width of Tape")	-	0	-
4.2("Fabric b) Linear Density")	-	0	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	0	-
4.3(Sacks)	-	0	-
4.4.1(Loose Liner)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.2(Visual Observation)	-	0	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.5(Laminated Fabric)	-	0	-
4.5(Lamination Over Hang of the fabric after trimming)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
4.7(Mouth of the Sack)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	0	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.5.3(Mass of Bale)	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	-
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	0	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17730 : Part 2 (2021)

Agro-Textiles Hail Protection Nets for Agriculture and Horticulture Purposes Specification Part 2 Woven Hail Protection Nets

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	200	-
Clause 7, table 1, (ii) a("Average breaking strength of Woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Warpway")	-	500	-
Clause 7,table 1, (ii) b("Average breaking strength of woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Weftway")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	10500	-
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only))	-	1200	-
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	400	-
Clause 7, table 1, (vi)(Shading percentage, percent, Max)	-	700	-
Clause 7, table 1, (vii)(Porosity, percent)	-	500	-
Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C)	-	700	-
Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min)	-	700	-
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (ii) a("Average breaking strength of Woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Warpway")	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7,table 1, (ii) b("Average breaking strength of woven hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Weftway")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection nets only))	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (vi)(Shading percentage, percent, Max)	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (vii)(Porosity, percent)	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (viii)(Cold cracking resistance test at –10 °C)	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
Clause 7, table 1, (ix)(Seam (joint) strength, percent, Min)	-	0	the test has been charged for type 1. hence not repeated again for type 2. The sample will be charged irrespective of type 1 or type 2 with above quoted charges
7.1(Dimensions)	-	400	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17730 : Part 1 (2021)

Agro-Textiles Hail Protection Nets for Agriculture and Horticulture Purposes Specification Part 1 Warp Knitted Hail Protection Nets

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7, Table 1, (i)(Mass in g/m2, (with a tolerance of ± 5 percent))	-	200	-
Clause 7, table 1, (ii) a("Average breaking strength of knitted hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(a) Wales direction")	-	500	-
Clause 7,table 1, (ii) b("Average breaking strength of knitted hail protection fabric (Strip method, 325 × 50 mm test piece with gauge length of 200 mm), N,Min,(b) Course direction")	-	0	-
Clause 7, table 1, (iii)("Retention of breaking strength after UV exposure of 144 hours, percent, Min")	-	10500	-
Clause 7,table 1, (iv)(Colour fastness to artificial light (Applicable for coloured hail protection only))	-	1200	-
Clause 7, table 1, (v)(Bursting pressure, kgf/cm2, Min)	-	400	-
Clause 7, table 1, (vi)(Shading percentage, percent, Max)	-	700	-
Clause 7, table 1, (vii)(Cold cracking resistance test at – 10 °C)	-	700	-
Clause 7, table 1, (viii)(Seam (joint) strength, percent, Min)	-	700	-
4.1(HDPE Monofilament (linear density))	-	400	-
4.1.1(Heat shrinkage at 60 degree to 95 degree)	-	1000	-
6.1(Fabric (width))	-	200	-
6.2(Reinforcement)	-	200	-
6.4(Stitching)	-	200	-
6.5(Colour)	-	200	-
7.1(Length, Width)	-	400	-
6.3(Joints)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17349 (2020)

Medical textiles – Shoe covers – Specification

8400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Workmanship and finish)	-	200	-
5.2 - Table 1 - (i)(Cleanliness - Microbial)	-	2000	-
5.2 - Table 1 - (ii)(Tensile Strength)	-	1000	-
5.2 - Table 1 - (iii)(Bursting Strength)	-	800	-
6(Packing)	-	200	-
7(Marking)	-	200	-
5(Requirements)	-	0	-
5.1(Workmanship and Finish)	-	200	-
5.2- Table 1- i)(Cleanliness – Microbial)	-	2000	-
5.2- Table 1- ii)(Tensile strength)	-	1000	-
5.2- Table 1- iii)(Bursting strength)	-	800	-
6(Packing)	-	0	-
7(Marking)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17354 (2020)

Medical textiles – Dental bib/Napkins – Specification

9200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 4(Manufacture)	-	200	-
Clause No. 5.1(Hygenic Condition)	-	200	-
Clause No. 5.2 (i)(Waterproofness)	-	500	-
Clause No. 5.2 (ii)(Cleanliness – Microbial (CFU/100 cm))	-	2000	-
Clause No. 5.2 (iii)(Tensile strength (dry and wet))	-	1000	-
Clause No. 5.2 (iv)-a(Absorption, Sinking Time)	-	400	-
5.1(REQUIREMENTS - Workmanship and Finish)	-	200	-
5.2-Table 1- i)(Performance Requirements - Waterproofness)	-	500	-
5.2-Table 1- ii)(Performance Requirements - Cleanliness – Microbial (CFU/100 cm))	-	2000	-
5.2-Table 1- iii)(Performance Requirements - Tensile strength (dry and wet), N Min)	-	1000	-
5.2-Table 1- iv)(Performance Requirements - Absorption)	-	400	-
6(PACKING)	-	200	-
7(MARKING)	-	200	-
Clause No. 5.2 (iv)-b(Absorption, Water holding capacity)	-	400	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17514 (2021)

Reusable Sanitary PadSanitary Napkin Period panties Specification

16200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material- Cover/Top sheet)	-	200	-
3.2(Material- Absorbent Core)	-	200	-
3.3(Material- Bottom Layer)	-	200	-
4.0(Manufacturing , workmanship and finish)	-	200	-
5.0(Fastening Mechanism)	-	200	-
6.0(Sizes:- Pad Length and Pad Width (For Absorbent core only))	-	400	-
7.0(Washing , Drying And Handling Instruction)	-	1000	-
8 & 11.2.4, Table 1, (i)(Colour Fastness to Rubbing)	-	250	-
8 & 11.2.4, Table 1, (ii)(Colour Fastness to Perspiration (Acidic & Alkaline))	-	400	-
8 & 11.2.4, Table 1, (iii)(Colour Fastness to Washing)	-	400	-
9.1(pH Value)	-	300	-
9.2(Ability to Withstand Pressure after Absorption)	-	1000	-
9.3.1(Bacterial and Fungal Bioburden)	-	2000	-
9.3.2(Test for Common Skin Pathogen -Staphylococcus Aureus)	-	500	-
12.0(Marking & Packing)	-	200	-
13.0(Marking & Packing)	-	200	-
Clause No. 6(Pad length and width)	-	400	-
Clause No. 8, Table No. 1, (i)(Colour fastness to rubbing of fabric)	-	250	-
Clause No. 8, Table No. 1, (ii)(Colour fastness to perspiration (acidic and alkaline))	-	400	-
Clause No. 8, Table No. 1, (iii)(Colour fastness to washing)	-	400	-
Clause No. 9.1(pH Value)	-	300	-
Clause No. 9.2(Ability to Withstand Pressure after Absorption)	-	1000	-
Clause No. 9.3(Hygiene Testing Requirement)	-	2000	-
Clause No. 9.3.1(Bacterial and Fungal Bioburden)	-	500	-
Clause No. 9.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus)	-	2800	-
Clasue No. 10(Anti-Bacterial Activity Value)	-	500	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

25600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Cord Beading - IS 15907)	-	400	-
5.1(MANUFACTURE- IS 15907)	-	900	-
5.2.1(Lamination- IS 15907)	-	200	-
5.2.1(Thickness of coating film- method A of IS 13162 (Part 3))	-	200	-
5.2.1(Lamination- IS 15907)	-	200	-
5.2.2(Lamination- IS 15907)	-	200	-
5.2.2(Lamination- IS 15907)	-	200	-
5.2.2(coating thickness of the sandwich lamination- method A of IS 13162 (Part 3))	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(The width of the hem - IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Finished width of pocket - IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.4(Bonding- IS 15907)	-	200	-
6- Table 1- SL.No (i)(Mass)	-	200	-
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	500	-
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,weft - IS 1969 )	-	0	-
6- Table 1- SL.No (iii)(Elongation at break of fabric- IS 1969)	-	0	-
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	10500	-
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	700	-
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	700	-
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	500	-
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	0	-
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	700	-
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	1000	-
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	1200	-
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	1200	-
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	400	-
6.1(Length -IS 15907)	-	200	-
6.1(Width - IS 15907)	-	200	-
6.1(Height - IS 15907)	-	200	-
6.2(Water Proofness,IS 7941)	-	500	-
6.2(Water Proofness, IS 7940)	-	500	-
4.1(Identification)	-	500	-
4.1(Linear Density)	-	400	-
4.1(Width)	-	200	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16390 (2015)

Agro textiles - Nylon knitted seamless gloves for tobacco harvesters - Specification

8200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Yarn)	-	400	-
4.2(Gloves)	-	1000	-
4.2.1(The gloves shall be of the design)	-	400	-
4.3(Freedom from Defects)	-	500	-
5.1(Dimensions and Mass)	-	1200	-
5.2(Wales and Courses)	-	1000	-
5.3(The gloves shall also conform)	-	2300	-
5.4(Sealed Sample)	-	0	-
5.4.1(The custody of the sealed)	-	0	-
6.1(The gloves shall be matched and paired)	-	200	-
6.1.1(difference of 1.0 cm in the overall length permissible while pairin Quantitative)	-	200	-
9.1(Lot)	-	0	-
9.2(Unless otherwise)	-	1000	-
4.1(Yarn)	-	0	-
4.2(Gloves)	-	0	-
4.3(Freedom from Defects)	-	0	-
5.1(Dimensions and Mass)	-	0	-
5.2(Wales and Courses)	-	0	-
5.3(The gloves shall also conform)	-	0	-
5.4(Sealed Sample)	-	0	-
6.1(The gloves shall be matched and paired)	-	0	-
9.1.1(The conformity of the lot)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17371 (2020)

Geosynthetics – Geogrids for flexible pavements – Specification

236000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1("Ultimate tensile strength, (MD × CD)- IS 16635 30/30 40/40 50/50 60/60 80/80 100/100")	-	1500	-
1("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
1("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
1(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	31500	-
1(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	5000	-
2("Ultimate tensile strength, (MD × CD)- IS 16635 20/20 30/30 40/40")	-	1500	-
2("Tensile strength at 2 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
2("Tensile strength at 5 percent strain, (MD × CD- IS 16635 20/20 30/30 40/40")	-	0	-
2(UV resistance, strength retained after 500 h exposure- IS 13162 (part 2))	-	31500	-
2(Chemical resistance, strength retained after 72 h immersion- IS 17363)	-	5000	-
2("Junction strength- IS 17371 AnnexB 20/20 30/30 40/40")	-	1000	-
Clause No. 4.1(Geogrid Raw Materials)	-	1200	-
Clause No. 4.5(Identification of Geogrid)	-	500	-
Clause No. 5.2, Table No. 1 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PET Geogrids)	-	1500	-
Clause No. 5.2, Table No. 1 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PET Geogrids)	-	0	-
Clause No. 5.2, table No. 1 (iv)(UV resistance, strength retained after 500 h exposure of PET Geogrids)	-	31500	-
Clause No. 5.2, Table No. 1 (v)(Chemical resistance, strength retained after 72 h immersion of PET Geogrids)	-	5000	-
Clause No. 5.2, table No. 1 (vi)(Width of PET Geogrids)	-	200	-
Clause No. 5.2, Table No. 1 (vii)(Roll length of PET Geogrids)	-	200	-
Clause No. 5.2, Table No. 2 (i)(Ultimate tensile strength, (MD × CD) kN/m of PP Geogrids)	-	1500	-
Clause No. 5.2, Table No. 2 (ii)(Tensile strength at 2 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, Table No. 2 (iii)(Tensile strength at 5 percent strain, (MD × CD) kN/m of PP Geogrids)	-	0	-
Clause No. 5.2, table No. 2 (iv)(UV resistance, strength retained after 500 h exposure of PP Geogrids)	-	31500	-
Clause No. 5.2, Table No. 2 (v)(Chemical resistance, strength retained after 72 h immersion of PP Geogrids)	-	5000	-
Clause No. 5.2, Table No. 2 (vi)(Junction strength, percent strength of original strength)	-	1000	-
Clause No. 5.2, table No. 2 (vii)(Width of PP Geogrids)	-	200	-
Clause No. 5.2, Table No. 2 (viii)(Roll length of PP Geogrids)	-	200	-
4.1(MATERIALS - Geogrid materials shall be inert to all chemicals naturally found in commonly encountered soils not containing adverse solvents and at ambient temperatures)	-	1200	-
4.5(MATERIALS - Identification of Geogrid)	-	500	-
5.1(REQUIREMENTS FOR GEOGRIDS -Geogrids shall be dimensionally stable and able to retain their geometry under manufacture, transport, and installation)	-	0	-
5.2- Table 1- i)(REQUIREMENTS FOR PET GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	1500	-
5.2- Table 1- ii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 1- iii)(REQUIREMENTS FOR PET GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 1- iv)(REQUIREMENTS FOR PET GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	31500	-
5.2- Table 1- v)(REQUIREMENTS FOR GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	5000	-
5.2- Table 1- vi)(REQUIREMENTS FOR PET GEOGRIDS - Width)	-	200	-
5.2- Table 1- vii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	200	-
5.2- Table 2- i)(REQUIREMENTS FOR PP GEOGRIDS - Ultimate tensile strength, (MD × CD) kN/m)	-	1500	-
5.2- Table 2- ii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 2 percent strain, (MD × CD) kN/m)	-	0	-
5.2- Table 2- iii)(REQUIREMENTS FOR PP GEOGRIDS - Tensile strength at 5 percent strain, (MD × CD) kN/m,)	-	0	-
5.2- Table 2- iv)(REQUIREMENTS FOR PP GEOGRIDS - UV resistance, strength retained after 500 h exposure)	-	31500	-
5.2- Table 2- v)(REQUIREMENTS FOR PP GEOGRIDS - Chemical resistance, strength retained after 72 h immersion)	-	5000	-
5.2- Table 2- vi)(REQUIREMENTS FOR PP GEOGRIDS - Junction strength, percent strength of original strength)	-	1000	-
5.2- Table 2- vii)(REQUIREMENTS FOR PP GEOGRIDS - Width)	-	200	-
5.2- Table 2- vIii)(REQUIREMENTS FOR PET GEOGRIDS - Roll length)	-	200	-
6(MARKING AND LABELLING)	-	0	-
7(PACKING - minimum thickness of packing film)	-	0	-
8.1(IDENTIFICATION, DELIVERY, STORAGE AND HANDLING)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16202 (2014)

Agro textiles - Woven ground covers for horticulture application - Specification

16600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Linear Density, Denier)	-	400	-
4.1(Heat Shrinkage, %)	-	500	-
4.1(Heat Shrinkage, %)	-	500	-
4.2(Plain Weave & Sett, ends & picks/dm)	-	800	-
4.3(Colour)	-	200	-
5.1, Table-1(Mass, g/m² , IS 1964)	-	200	-
5.1, Table-1(Tensile Test, Kgf, IS 1969,Part-2)	-	500	-
5.1, Table-1(Tear Strength, Kgf, IS 6489,Part-1)	-	500	-
5.1, Table-1(Air permeability, cft/ft²/s, IS 11056)	-	500	-
5.1, Table-1(Index puncture resistance, kgf, Annexure-B)	-	700	-
5.1, Table-1(UV accelerated exposure testing, Annexure-C)	-	10500	-
5.1, Table-1(Water permeability, lt/m2 /s, IS 14324)	-	700	-
5.2(Dimension and Mass)	-	400	-
Clause No. 4.1(linear density of polypropylene tape)	-	0	-
Clause No. 4.1(Heat shrinkage of the tape at 60 and 90℃)	-	0	-
Clause No. 4.2(Fabric ground cover)	-	0	-
Clause No. 5.1, Table No. 1, (i)(Mass, g/m2)	-	0	-
Clause No. 5.1, Table No. 1, (ii)(Tensile strength (grab), kgf)	-	0	-
Clause No. 5.1, Table No. 1, (iii)(Tear strength, kgf)	-	0	-
Clause No. 5.1, Table No. 1, (iv)(Air permeability, cft/ft²/s)	-	0	-
Clause No. 5.1, Table No. 1, (v)(Index puncture resistance, kgf)	-	0	-
Clause No. 5.1, Table No. 1, (vi)(UV accelerated exposure testing, percent strength retained)	-	0	-
Clause No. 5.1, Table No. 1, (vii)(Water permeability lt/m2/s)	-	0	-
Clause No. 5.2(Dimensions and Mass)	-	0	-
Clause No. 7(Packing thickness)	-	200	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16008 : Part 2 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 2 Shade nets made from mono filament yarns (first revision)

18900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Material)	-	500	-
4.1(HDPE Mono filament)	-	400	-
4.1(HDPE Mono filament)	-	400	-
4.1.1(HDPE Mono filament)	-	400	-
4.2(Fabric)	-	200	-
4.3(Colour)	-	400	-
5.0(Types)	-	2100	-
6.0(Requirements)	-	200	-
6.1(Dimensions and mass)	-	400	-
6.2(Dimensions and mass)	-	400	-
6.2 Table 1(Mass g/m2,Min)	-	200	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method,Warpway,Weftway 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min )	-	500	-
6.2 Table 1(Warpway Weftway)	-	0	-
6.2 Table 1(Retention of breaking strength after UV exposure, N, Min)	-	10500	-
6.2 Table 1(Colour fastness to artificial light1)	-	1200	-
6.2 Table 1(Bursting pressure, kgf/cm2, Min)	-	400	-
6.2 Table 1(Shading %)	-	700	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17630 (2021)

Medical Textiles Bedsheet and Pillow Cover Specification

10050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(WORKMANSHIP AND FINISH)	-	200	-
6(GENERAL REQUIREMENTS - Fabric Washing & Tumble Drying)	-	400	-
6- Table 1- i)(GENERAL REQUIREMENTS - Colour fastness to rubbing a) Dry 4 or better b) Wet)	-	250	-
6- Table 1- ii)(GENERAL REQUIREMENTS - Colour fastness to perspiration (acidic and alkaline) a) Colour change b) Staining)	-	400	-
6- Table 1- iii)(GENERAL REQUIREMENTS - Colour fastness to washing a) Colour change b) Staining)	-	400	-
6- Table 1- iv)(GENERAL REQUIREMENTS - Colour fastness to light Color change)	-	1200	-
6- Table 1- v)(GENERAL REQUIREMENTS - Dimensional stability to washing, percentage Length and width)	-	500	-
6- Table 1- vi)(GENERAL REQUIREMENTS - Pilling resistance)	-	400	-
6- Table 1- vii)(GENERAL REQUIREMENTS - Scouring loss, percent, Max (for cotton))	-	300	-
7.1- Table 2- i)(PERFORMANCE REQUIREMENTS - Tensile strength (dry and wet) (N))	-	1000	-
7.1- Table 2- ii)(PERFORMANCE REQUIREMENTS - Bursting strength (dry and wet) (kPa))	-	800	-
7.1- Table 2- iii)(PERFORMANCE REQUIREMENTS - Seam strength (dry and wet) (N))	-	1400	-
7.1- Table 2- iv)(PERFORMANCE REQUIREMENTS - pH)	-	300	-
7.1- Table 2- v)(PERFORMANCE REQUIREMENTS - Water soluble substance, percent)	-	300	-
7.1- Table 2- vi)(PERFORMANCE REQUIREMENTS - Cleanliness–microbial (CFU/100 cm2))	-	2000	-
9(MARKING)	-	200	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17509 (2021)

Disposable Baby Diaper Specification

11900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause no. 3(Material)	-	200	-
Clause no. 3.1(Top Cover / Top Sheet)	-	200	-
Clause no. 3.2(Absorbent Core)	-	200	-
Clause no. 3.3(Outer Protective Barrier or Back Sheet)	-	200	-
Clause no. 4(Fastening & Securing Mechanism)	-	200	-
Clause no. 5(ManufactureWorkmanship and Finish)	-	200	-
Clause no.6(Type and Size: FOR X LARGE)	-	200	-
Clause no.6(Diaper Length)	-	200	-
Clause no.6(Diaper Width)	-	200	-
Clause no.6(Diaper Crotch)	-	200	-
Clause no.6(Absorbent Core Length)	-	200	-
Clause no.6(Absorbent Core Width Back)	-	200	-
1()	-	0	-
Clause no.6(Absorbent Core Length)	-	200	-
Clause no.6(Absorbent Core Width Front)	-	200	-
Clause no.6(Core Cortch)	-	200	-
Clause no.7(Performance Requirements)	-	0	-
Clause no.7.1(pH Value)	-	300	-
Clause no.7.2 Table-2(Minimum absorption Capacity (X Large))	-	300	-
Clause no.7.2 Table-2(Rewet under Load (All Sizes))	-	500	-
Clause no.7.2 Table-2(Rate of Absorption (All Sizes))	-	300	-
Clause no.7.3(Hygiene Testing Requirement, Total Viable Count)	-	2000	-
Clause no.7.3(Hygiene Testing Requirement, Staphylococcus Aureus)	-	500	-
Clause no.7.7(Anti-Bacterial Activity Value (optional))	-	2800	-
9 & 9.1(Marking)	-	200	-
10(Packing)	-	200	-
Clause no.7.5(Phthalate Test)	-	1800	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 5405 (2019)

Sanitary napkins – Specification (second revision)

12400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(SIZES, Regular )	-	200	-
Cl 5(SIZES, Large)	-	200	-
Cl 5(SIZES, Extra Large)	-	200	-
Cl 5(SIZES, XXL)	-	200	-
Cl 5(Absorbent Capacity, Regular )	-	400	-
Cl 5(Absorbent Capacity, Large)	-	400	-
Cl 5(Absorbent Capacity, Extra Large)	-	400	-
Cl 5(Absorbent Capacity, XXL)	-	400	-
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	300	-
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	400	-
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	2000	-
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	500	-
Cl 5(SIZES, Regular )	-	200	-
Cl 5(SIZES, Large)	-	200	-
Cl 5(SIZES, Extra Large)	-	200	-
Cl 5(SIZES, XXL)	-	200	-
Cl 5(Absorbent Capacity, Regular )	-	400	-
Cl 5(Absorbent Capacity, Large)	-	400	-
Cl 5(Absorbent Capacity, Extra Large)	-	400	-
Cl 5(Absorbent Capacity, XXL)	-	400	-
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	300	-
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	400	-
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	2000	-
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	500	-
3.1(Cover/Top sheet)	-	200	-
3.2(Absorbent Core)	-	200	-
3.3(Barrier or Bottom Sheet)	-	200	-
4.1 (1)(Type and shapes of sanitary napkins)	-	200	-
4.2(Sanitary napkins shape & design)	-	200	-
6.0(Manufacture, workmanship & finish)	-	200	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17356 (2020)

Agro textiles – Windshield nets for agriculture and horticulture purposes - Specification

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 4.1(HDPE Monofilament density)	-	200	-
Clause No. 4.1.1(Heat Shrinkage at 60 and 95℃)	-	400	-
Clause No. 5.1(Width of the Fabric)	-	200	-
Clause No. 5.2.1(Length of the Eyelet)	-	200	-
Clause No. 5.2.1(Eyelet to Eyelet Edge Distance)	-	0	-
Clause No. 6(Mass of the windshield nets)	-	200	-
Clause No. 6(Wind Speed Suitability)	-	200	-
Clause 7.1(Dimensions)	-	200	-
Clause 7.2 (i)(Mass g/m²)	-	200	-
Clause 7.2 (ii)(Average breaking strength of wind shield net fabric (Strip method, 325×50 mm test piece with gauge length of 200 mm))	-	500	-
Clause 7.2 (iii)(Retention of breaking strength after UV exposure of 144 h)	-	10500	-
Clause 7.2 (iv)(Colour fastness to artificial light)	-	1200	-
Clause 7.2 (v)(Bursting pressure, kgf/cm2)	-	400	-
Clause 7.2 (vi)(Wind blockage, percent)	-	700	-
Clause 8.1(Length of the rolled windshield nets)	-	200	-
4.1(MATERIALS - HDPE Monofilament)	-	500	-
5.1(MANUFACTURE - Fabric)	-	200	-
5.2(MANUFACTURE - Eyelet)	-	0	-
5.3(MANUFACTURE - Colour)	-	200	-
6(TYPES - a) Type 1, b) Type 2)	-	400	-
7.1(REQUIREMENTS - Dimensions and Mass)	-	400	-
7.2-Table 2- i)(REQUIREMENTS - Mass g/m2)	-	200	-
7.2-Table 2- ii)(REQUIREMENTS - Average breaking strength of wind shield net fabric (Strip method, 325×50 mm test piece with gauge length of 200 mm),N a) Warpway b) Weftway)	-	500	-
7.2-Table 2- iii)(REQUIREMENTS - Retention of breaking strength after UV exposure of 144 h, percent)	-	10500	-
7.2-Table 2- iv)(REQUIREMENTS - Colour fastness to artificial light)	-	1200	-
7.2-Table 2- v)(REQUIREMENTS - Bursting pressure, kgf/cm2)	-	400	-
7.2-Table 2- vi)(REQUIREMENTS - Wind blockage, percent)	-	700	-
8.1(Packing)	-	0	-
8.2(Marking)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16008 : Part 1 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 1 Shade nets made from tape yarns (first revision)

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Types)	-	700	-
6.1(Dimensions and Mass - IS 1954)	-	200	-
6.1(Dimensions and Mass - IS 1954)	-	200	-
6.2 Table 1(Mass - IS 1964)	-	200	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	500	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	500	-
6.2 Table 1(Retention of breaking strength after UV exposure - IS 1969 (Part 1))	-	10000	-
6.2 Table 1(Colour fastness to artificial light, IS 2454)	-	1200	-
6.2 Table 1(Bursting Pressure, IS 1966 (Part 1 or 2))	-	400	-
6.2 Table 1(Shading Percentage)	-	700	-
4.3, 4(Colour)	-	200	-
4.2, 4(Fabric )	-	600	-
4.1.1, 4(HDPE Tapes Heat shrinkage )	-	1000	-
4.1, 4( HDPE Tapes Linear density )	-	200	-
4.1, 4(HDPE Tapes Width )	-	200	-
4.1, 4(HDPE Tapes UV stabilizer)	-	1200	-
4.1, 4(HDPE Tapes Material Identification )	-	500	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 12171 (2019)

Cotton bales – Specification (third revision)

2900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.3(Moisture Content)	-	500	-
5.2.1(Dimensions)	-	200	-
5.2.2(Mass (Weight))	-	200	-
5.2.3.1(a) Cotton fabric)	-	200	-
5.2.3.1(b) Baling hoops)	-	400	-
5.2.3.1(c) Cotton twine)	-	1400	-
5.1.4(Strength of Fibre)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16089 (2013)

Jute agro-textile – Sapling bags for growth of seedling/ sapling – Specification

2200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4, Table 1, (i)(Mass, g/m², Min)	-	200	-
Clause 4, Table 1, (ii)(Thickness, mm)	-	200	-
Clause 4, Table 1, (iii)(Open area, percent)	-	0	-
Clause 4, Table 1, (iv) a(Threads/dm, Warp)	-	200	-
Clause 4, Table 1, (iv) b(Threads/dm, Weft)	-	0	-
Clause 4, Table 1, (v)(Width of Hessian fabric, cm)	-	200	-
Clause 4, Table 1, (vi)(Length and width of sapling bags, cm, Min)	-	400	-
Clause 4, Table 1, (vii)(Water holding capacity, percent)	-	500	-
Clause 4, Table 1, (viii) a(Tensile strength, kN/m, Warp)	-	500	-
Clause 4, Table 1, (viii) b(Tensile strength, kN/m, Weft)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17070 (2019)

Jute agrotextiles for growth of plant and suppression of weeds – Specification

5100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 -Table 1 -(i)(Mass at 20 percent moisture regain)	-	400	-
5 -Table 1 -(ii)(Thickness)	-	200	-
5 -Table 1 -(iii)(Width)	-	200	-
5 -Table 1 -(iv)(Wide width tensile strength)	-	1500	-
5 -Table 1 -(v)(Tear strength)	-	500	-
5 -Table 1 -(vi)(Bursting strength)	-	400	-
5 -Table 1 -(vii)(Index Puncture resistance)	-	700	-
5-Table 1 -(ix)(Water permittivity)	-	700	-
5 -Table 1 -(viii)(Air permeability)	-	500	-
8(Marking)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 16718 (2021)

Textiles - Polypropylene Spun Bonded Non-Woven Crop Covers and Fruit Skirting Bags for Agricultural and Horticultural Applications - Specification (first revision)

18700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Raw Material)	-	500	-
5.2.2(Width of fabric)	-	200	-
5.4.2 -Table 1-(i)(Mango, Orange)	-	400	-
5.4.2 - Table 2 - (i)(Thickness)	-	200	-
5.4.2 - Table 2 - (ii)(Fabric mass)	-	200	-
5.4.2 - Table 2 - (iii)(Breaking strength)	-	500	-
5.4.2 - Table 2 - (iv)(Elongation at break)	-	0	-
5.4.2 - Table 2 - (v)(Trapezoid tear strength)	-	500	-
5.4.2 - Table 2 - (vi)(Air permeability)	-	500	-
5.4.2 - Table 2 - (viii)(UV stability test)	-	10500	-
5.4.2 - Table 2 - (ix)(Ash content)	-	800	-
5.4.2 - Table 2 - (x)(Index puncture resistance)	-	700	-
5.4.2 - Table 2 - (xi)(Water absorption capacity)	-	700	-
5.4.2 - Table 2 - (xii)(Colour)	-	400	-
5.4.2 -Table 1-(ii)(Banana bunch)	-	400	-
5.4.2 -Table 1-(iii)(Grape bunch)	-	400	-
5.4.2 -Table 1-(iv)(Pomegranate)	-	400	-
5.4.2 -Table 1-(v)(Papaya)	-	400	-
8.1.2(Marking)	-	0	-
5.4.2 - Table 2 - (vii)(water vapour permeability)	-	1000	-

Complete

14 Dec, 2023

14 Dec, 2026

IS 17731 (2021)

Agro-Textiles Laminated Woven Orchard Protection Covers Specification

68500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 7, Table 1, (i)(Thickness, mm, Min)	-	200	-
Clause no. 7, Table 1, (ii)(Mass, g/m2, Min)	-	200	-
Clause No. 7, Table 1, (iii) a("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (a) Warpway")	-	500	-
Clause No. 7, Table 1, (iii) b("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (b) Weftway")	-	500	-
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	60500	-
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	0	-
Clause No. 7, Table 1, (v)(Strain at maximum load, percent)	-	0	-
Clause No. 7, Table 1, (vi)("Impact failure load at 1524 mm drop, Min, gram force at 50 percent failure")	-	700	-
Clause No. 7, Table 1, (vii)(Reinforcement band strength, N, Min)	-	500	-
Clause No. 7, Table 1, (viii)(Ash content, percent, Max)	-	500	-
Clause No. 7, Table 1, (ix)(Total visible light transmission, percent)	-	700	-
Clause No. 7, Table 1, (x)(Light diffusion, percent)	-	700	-
Clause No. 7, Table 1, (xi)(Thermicity IR effectiveness, percent)	-	1800	-
Clause No. 4.1(Width and linear density of HDPE Tapes)	-	200	-
Clause No. 4.1.1(Heat shrinkage of HDPE Tapes)	-	500	-
Clause No. 6.1.1(Coating Lamination thickness, micron)	-	600	-
Clause No. 6.1.2(Sandwich lamination thickness , micron)	-	400	-
Clause No. 6.2(Joints/Seams)	-	0	-
Clause No. 6.3(Number and position of metal eyelets)	-	0	-
Clause No. 7.1(colour , texture and finish)	-	0	-

Complete

14 Dec, 2023

14 Dec, 2026

Bureau of Indian Standards

The National Standards Body of India

The Synthetic and Art Silk Mills' Research Association

SASMIRA, SASMIRA Marg, WORLI,, MUMBAI, Mumbai, Maharashtra, 400030

9850251038 mmti@sasmira.org

Scope List