BIS - LIMS (Laboratory Information Management System)

KC INDIA TEST LABORATORIES LLP

A-16/2, Site-IV, Sahibabad Industrial Area, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

9599880265 kcitestlab@gmail.com

Scope List

Reset

27 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

Upto and including 16A

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(RATINGS)	-	150	NIL
7.1.1(Accessories Classification)	-	150	NIL
7.1.2(Accessories Classification)	-	150	NIL
7.1.3(Accessories Classification)	-	150	NIL
7.1.4(Accessories Classification)	-	150	NIL
7.1.5(Accessories Classification)	-	150	NIL
7.2.1(Socket-Outlets Classification)	-	150	NIL
7.2.2(Socket-Outlets Classification)	-	150	NIL
7.2.3(Socket-Outlets Classification)	-	150	NIL
7.2.4(Socket-Outlets Classification)	-	150	NIL
7.3(Plug Classification)	-	150	NIL
8(Marking)	-	150	NIL
9(CHECKING OF DIMENSIONS)	-	500	NIL
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	400	NIL
11(Provision for earthing)	-	400	NIL
12(terminals)	-	500	NIL
13.1(Construction of fixed Socket Outlets)	-	800	NIL
13.2(Construction of fixed Socket Outlets)	-	800	NIL
13.3(Construction of fixed Socket Outlets)	-	800	NIL
13.4(Construction of fixed Socket Outlets)	-	800	NIL
13.5(Construction of fixed Socket Outlets)	-	800	NIL
13.6(Construction of fixed Socket Outlets)	-	800	NIL
13.7(Construction of fixed Socket Outlets)	-	800	NIL
13.8(Construction of fixed Socket Outlets)	-	800	NIL
13.9(Construction of fixed Socket Outlets)	-	800	NIL
13.10(Construction of fixed Socket Outlets)	-	800	NIL
13.11(Construction of fixed Socket Outlets)	-	800	NIL
13.12(Construction of fixed Socket Outlets)	-	800	NIL
13.13(Construction of fixed Socket Outlets)	-	800	NIL
13.14(Construction of fixed Socket Outlets)	-	800	NIL
13.15(Construction of fixed Socket Outlets)	-	800	NIL
13.16(Construction of fixed Socket Outlets)	-	800	NIL
13.17(Construction of fixed Socket Outlets)	-	800	NIL
13.18(Construction of fixed Socket Outlets)	-	800	NIL
13.19(Construction of fixed Socket Outlets)	-	800	NIL
13.2(Construction of fixed Socket Outlets)	-	800	NIL
13.21(Construction of fixed Socket Outlets)	-	800	NIL
13.22(Construction of fixed Socket Outlets)	-	800	NIL
13.23(Construction of fixed Socket Outlets)	-	800	NIL
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.10(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.20(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
14.26(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	800	NIL
15(INTERLOCKED SOCKET-OUTLETS)	-	400	NIL
16.1(Resistance to Ageing)	-	500	NIL
16.2(RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	500	NIL
16.3(Resistance to Humidity)	-	500	NIL
17.1(RESISTANCE AND ELECTRIC STRENGTH)	-	700	NIL
17.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	700	NIL
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	700	NIL
18(OPERATION OF EARTHING CONTACTS)	-	700	NIL
19(TEMPERATURE RISE)	-	1000	NIL
20(Making & Breaking Capacity)	-	1500	NIL
21(Normal Operation)	-	2500	NIL
22.1(Verification of the Maximum Withdrawal Force)	-	150	NIL
22.2(Verification of Minimum Withdrawal Force)	-	150	NIL
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	150	NIL
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	150	NIL
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	150	NIL
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	150	NIL
24.1(MECHANICAL STRENGTH For all kinds of fixed socketoutlets)	-	150	NIL
24.1(MECHANICAL STRENGTH For portable multiple and combined socket outlets with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	150	NIL
24.1(MECHANICAL STRENGTH For surface mounting boxes)	-	150	NIL
24.2(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	150	NIL
24.2(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.3(MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-	150	NIL
24.4(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	150	NIL
24.4(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.5(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	150	NIL
24.5(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.5(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	150	NIL
24.6(MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-	150	NIL
24.7(MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-	150	NIL
24.8(MECHANICAL STRENGTH For shuttered socketoutlets)	-	150	NIL
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	150	NIL
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	150	NIL
24.10(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	150	NIL
24.10(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	150	NIL
24.11(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	150	NIL
24.12(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	150	NIL
24.13(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	150	NIL
24.14.1(MECHANICAL STRENGTH For fixed socket-outlets)	-	150	NIL
24.14.2(MECHANICAL STRENGTH For fixed socket-outlets)	-	150	NIL
24.14.3(MECHANICAL STRENGTH For plugs and portable socketoutlets)	-	150	NIL
24.15(MECHANICAL STRENGTH)	-	150	NIL
24.16(MECHANICAL STRENGTH)	-	150	NIL
24.16(MECHANICAL STRENGTH For shroud of portable socket-outlets)	-	150	NIL
25.1(Resistance to heat)	-	250	NIL
25.2(Resistance to heat)	-	250	NIL
25.3(Resistance to heat)	-	250	NIL
25.4(Resistance to heat)	-	250	NIL
26.1(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.2(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.3(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.4(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.5(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.6(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
26.7(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	NIL
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	NIL
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	NIL
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	NIL
28.1.1(Glow-Wire Test)	-	500	NIL
28.2(Resistance to Tracking)	-	500	NIL
29(Resistance to Rusting)	-	500	NIL
30.1(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-	500	NIL
30.2(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-	500	NIL
30.3(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-	500	NIL
30.4(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-	500	NIL

Complete

19 Jul, 2024

06 Jun, 2027

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

Upto and including 2500 KVA

125000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13.1(Marking (Rating Plates))	-	100	NIL
13.2(Terminal Marking Plate)	-	100	NIL
13.3(Marking )	-	100	NIL
13.4(Marking)	-	100	NIL
13.4.1(Marking)	-	100	NIL
14.1(MOUNTING ARRANGEMENT)	-	100	NIL
14.2(MOUNTING ARRANGEMENT)	-	100	NIL
14.3(MOUNTING ARRANGEMENT)	-	100	NIL
14.4(MOUNTING ARRANGEMENT)	-	100	NIL
15.1.1(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.2(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.3(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.4(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.5(TRANSFORMER TANK : Construction)	-	100	NIL
21.2 a)(Measurement of winding resistance )	-	100	NIL
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	4000	NIL
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	4000	NIL
21.2 d)(Measurement of no-load loss and current)	-	4000	NIL
21.2 e)(Measurement of insulation resistance)	-	2000	NIL
21.2 f)(Induced over-voltage withstand test)	-	2000	NIL
21.2 g)( Separate-source voltage withstand test)	-	2000	NIL
21.5.3.3(Oil leakage test)	-	1000	NIL
21.3(a )(Lightning impulse test)	-	5500	NIL
21.3(b)(Temperature-rise test)	-	8000	NIL
21.4 a)( Determination of sound levels)	-	2500	NIL
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.3( Oil leakage test (routine test))	-	2000	NIL
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	2500	NIL
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	2500	NIL
21.5.3.3(Oil leakage test (routine test))	-	2500	NIL
21.4 c(No load current at 112.5 percent voltage.)	-	45000	NIL
21.4 d(Paint adhesion tests)	-	2500	NIL
21.4 e(BDV and moisture content of oil in the transformer)	-	4000	NIL
15.5(Total Dry Film Paint Thickness)	-	4000	NIL
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	2500	NIL
11(Minimum clearance in Air)	-	1000	NIL
16(Conservator for Non-sealed type Transformers)	-	1000	NIL
20(Fittings)	-	1000	NIL
6.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
7.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
8.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
6.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
7.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
8.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
21.5.1.3(Oil leakage test upto 200 KVA)	-	4000	NIL
9.1a)(CRGO Electrical Steel)	-	200	NIL
9.1 b)(Amorphous core material)	-	200	NIL
9.1 c)(Copper/Aluminium conductor)	-	200	NIL
9.1 d)(Kraft paper)	-	200	NIL
9.1 e)(Press Board)	-	200	NIL
9.1 f)(Mineral oil)	-	200	NIL
10(Terminal Arrangement)	-	200	NIL
15.2(Pressure and Vacuum Requirements)	-	200	NIL
15.4(Gasket)	-	200	NIL
19(Tolerances)	-	200	NIL
18(Efficiency and regulation)	-	1000	NIL
4(Service Conditions)	-	200	NIL
5(General )	-	200	NIL
6.1(Rating)	-	200	NIL
6.2(Rated frequency)	-	200	NIL
6.3(Nominal system voltage)	-	200	NIL
6.4(Basic Insulation level )	-	200	NIL
6.5(No-Load Voltage Ratios)	-	1000	NIL
6.6(Winding connections and phase displacement)	-	2000	NIL
6.7(Tapping Range and Tapping Method)	-	2000	NIL
6.8(Losses and impedance values)	-	1000	NIL
6.9(Permissible Flux Density and Over Fluxing )	-	1000	NIL
6.1(Limits of Temperature-rise)	-	2500	NIL
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	1000	NIL
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	1000	NIL
9(Standard Materials)	-	1000	NIL
10(Terminal arrangment )	-	1000	NIL
11(Minimum Clearnaces air )	-	1000	NIL
12(Connectors )	-	100	NIL
13(Marking )	-	200	NIL
14(Mounting arrangement)	-	200	NIL
15(Trasnformer Tank )	-	200	NIL
16(Conservator for Non-Sealed type Transformers)	-	200	NIL
18(Efficiency and Regulation)	-	1000	NIL
19(Tolerances)	-	200	NIL
20(Fittings)	-	200	NIL
21(General )	-	200	NIL
22(Information required with enquiry and order )	-	200	NIL
13.1(Marking (Rating Plates))	-	100	NIL
13.2(Terminal Marking Plate)	-	100	NIL
13.3(Marking )	-	100	NIL
13.4(Marking)	-	100	NIL
13.4.1(Marking)	-	100	NIL
14.1(MOUNTING ARRANGEMENT)	-	100	NIL
14.2(MOUNTING ARRANGEMENT)	-	100	NIL
14.3(MOUNTING ARRANGEMENT)	-	100	NIL
14.4(MOUNTING ARRANGEMENT)	-	100	NIL
15.1.1(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.2(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.3(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.4(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.5(TRANSFORMER TANK : Construction)	-	100	NIL
21.2 a)(Measurement of winding resistance )	-	100	NIL
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	4000	NIL
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	4000	NIL
21.2 d)(Measurement of no-load loss and current)	-	4000	NIL
21.2 e)(Measurement of insulation resistance)	-	2000	NIL
21.2 f)(Induced over-voltage withstand test)	-	2000	NIL
21.2 g)( Separate-source voltage withstand test)	-	2000	NIL
21.5.3.3(Oil leakage test)	-	1000	NIL
21.3(a )(Lightning impulse test)	-	5500	NIL
21.3(b)(Temperature-rise test)	-	8000	NIL
21.4 a)( Determination of sound levels)	-	2500	NIL
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.3( Oil leakage test (routine test))	-	2000	NIL
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	2500	NIL
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	2500	NIL
21.5.3.3(Oil leakage test (routine test))	-	2500	NIL
21.4 c(No load current at 112.5 percent voltage.)	-	45000	NIL
21.4 d(Paint adhesion tests)	-	2500	NIL
21.4 e(BDV and moisture content of oil in the transformer)	-	4000	NIL
15.5(Total Dry Film Paint Thickness)	-	4000	NIL
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	2500	NIL
11(Minimum clearance in Air)	-	1000	NIL
16(Conservator for Non-sealed type Transformers)	-	1000	NIL
20(Fittings)	-	1000	NIL
6.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
7.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
8.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
6.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
7.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
8.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
21.5.1.3(Oil leakage test upto 200 KVA)	-	4000	NIL
9.1a)(CRGO Electrical Steel)	-	200	NIL
9.1 b)(Amorphous core material)	-	200	NIL
9.1 c)(Copper/Aluminium conductor)	-	200	NIL
9.1 d)(Kraft paper)	-	200	NIL
9.1 e)(Press Board)	-	200	NIL
9.1 f)(Mineral oil)	-	200	NIL
10(Terminal Arrangement)	-	200	NIL
15.2(Pressure and Vacuum Requirements)	-	200	NIL
15.4(Gasket)	-	200	NIL
19(Tolerances)	-	200	NIL
18(Efficiency and regulation)	-	1000	NIL
4(Service Conditions)	-	200	NIL
5(General )	-	200	NIL
6.1(Rating)	-	200	NIL
6.2(Rated frequency)	-	200	NIL
6.3(Nominal system voltage)	-	200	NIL
6.4(Basic Insulation level )	-	200	NIL
6.5(No-Load Voltage Ratios)	-	200	NIL
6.6(Winding connections and phase displacement)	-	200	NIL
6.7(Tapping Range and Tapping Method)	-	2000	NIL
6.8(Losses and impedance values)	-	2000	NIL
6.9(Permissible Flux Density and Over Fluxing )	-	1000	NIL
6.1(Limits of Temperature-rise)	-	200	NIL
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	200	NIL
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	200	NIL
9(Standard Materials)	-	200	NIL
10(Terminal arrangment )	-	200	NIL
11(Minimum Clearnaces air )	-	1000	NIL
12(Connectors )	-	200	NIL
13(Marking )	-	200	NIL
14(Mounting arrangement)	-	200	NIL
15(Trasnformer Tank )	-	200	NIL
16(Conservator for Non-Sealed type Transformers)	-	200	NIL
18(Efficiency and Regulation)	-	1000	NIL
19(Tolerances)	-	200	NIL
20(Fittings)	-	200	NIL
21(General )	-	200	NIL
22(Information required with enquiry and order )	-	200	NIL
13.1(Marking (Rating Plates))	-	100	NIL
13.2(Terminal Marking Plate)	-	100	NIL
13.3(Marking )	-	100	NIL
13.4(Marking)	-	100	NIL
13.4.1(Marking)	-	100	NIL
14.1(MOUNTING ARRANGEMENT)	-	100	NIL
14.2(MOUNTING ARRANGEMENT)	-	100	NIL
14.3(MOUNTING ARRANGEMENT)	-	100	NIL
14.4(MOUNTING ARRANGEMENT)	-	100	NIL
15.1.1(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.2(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.3(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.4(TRANSFORMER TANK : Construction)	-	100	NIL
15.1.5(TRANSFORMER TANK : Construction)	-	100	NIL
21.2 a)(Measurement of winding resistance )	-	4000	NIL
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	4000	NIL
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	4000	NIL
21.2 d)(Measurement of no-load loss and current)	-	4000	NIL
21.2 e)(Measurement of insulation resistance)	-	2000	NIL
21.2 f)(Induced over-voltage withstand test)	-	2000	NIL
21.2 g)( Separate-source voltage withstand test)	-	2000	NIL
21.5.3.3(Oil leakage test)	-	1000	NIL
21.3(a )(Lightning impulse test)	-	5500	NIL
21.3(b)(Temperature-rise test)	-	8000	NIL
21.4 a)( Determination of sound levels)	-	2500	NIL
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	2500	NIL
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	2500	NIL
21.5.2.3( Oil leakage test (routine test))	-	2000	NIL
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	2500	NIL
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	2500	NIL
21.5.3.3(Oil leakage test (routine test))	-	2500	NIL
21.4 c(No load current at 112.5 percent voltage.)	-	45000	NIL
21.4 d(Paint adhesion tests)	-	2500	NIL
21.4 e(BDV and moisture content of oil in the transformer)	-	4000	NIL
15.5(Total Dry Film Paint Thickness)	-	4000	NIL
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	2500	NIL
11(Minimum clearance in Air)	-	1000	NIL
16(Conservator for Non-sealed type Transformers)	-	1000	NIL
20(Fittings)	-	1000	NIL
6.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
7.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
8.8 (50%)(Total losses at 50 % load (Watts))	-	2500	NIL
6.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
7.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
8.8 (100%)(Total losses at 100 % load (Watts))	-	2500	NIL
21.5.1.3(Oil leakage test upto 200 KVA)	-	1000	NIL
9.1a)(CRGO Electrical Steel)	-	200	NIL
9.1 b)(Amorphous core material)	-	200	NIL
9.1 c)(Copper/Aluminium conductor)	-	200	NIL
9.1 d)(Kraft paper)	-	200	NIL
9.1 e)(Press Board)	-	200	NIL
9.1 f)(Mineral oil)	-	200	NIL
10(Terminal Arrangement)	-	200	NIL
15.2(Pressure and Vacuum Requirements)	-	200	NIL
15.4(Gasket)	-	200	NIL
19(Tolerances)	-	200	NIL
18(Efficiency and regulation)	-	1000	NIL
4(Service Conditions)	-	200	NIL
5(General )	-	200	NIL
6.1(Rating)	-	200	NIL
6.2(Rated frequency)	-	200	NIL
6.3(Nominal system voltage)	-	200	NIL
6.4(Basic Insulation level )	-	200	NIL
6.5(No-Load Voltage Ratios)	-	1000	NIL
6.6(Winding connections and phase displacement)	-	2000	NIL
6.7(Tapping Range and Tapping Method)	-	2000	NIL
6.8(Losses and impedance values)	-	1000	NIL
6.9(Permissible Flux Density and Over Fluxing )	-	1000	NIL
6.1(Limits of Temperature-rise)	-	2500	NIL
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	1000	NIL
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	1000	NIL
9(Standard Materials)	-	1000	NIL
10(Terminal arrangment )	-	1000	NIL
11(Minimum Clearnaces air )	-	1000	NIL
12(Connectors )	-	100	NIL
13(Marking )	-	100	NIL
14(Mounting arrangement)	-	1000	NIL
15(Trasnformer Tank )	-	1000	NIL
16(Conservator for Non-Sealed type Transformers)	-	200	NIL
18(Efficiency and Regulation)	-	1000	NIL
19(Tolerances)	-	200	NIL
20(Fittings)	-	200	NIL
21(General )	-	200	NIL
22(Information required with enquiry and order )	-	200	NIL

Complete

19 Jul, 2024

06 Jun, 2027

included w.e.f.29.10.2024 Exclusion CL 17 ( ABILITY OF TRANSFORMERS TO WITHSTAND EXTERNAL SHORT CIRCUIT ) CL 21.3(c) (Short-circuit withstand test) CL 21.4 b (Short-circuit withstand test IS 2026 (Part 5) (above 200 kVA)) CL 17 (Ability of transformers to withstand external Short circuit )

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

Rating: Upto 35 Watt

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	400	20% Discount to BIS
6(Interchangeability)	-	2000	20% Discount to BIS
7(Protection against accidental contact with live parts)	-	5000	20% Discount to BIS
8(Insulation Resistance and Electric Strength)	-	2000	20% Discount to BIS
9(MECHANICAL STRENGTH)	-	1000	20% Discount to BIS
10(cap temperature)	-	1000	20% Discount to BIS
11(Resistance to Heat)	-	1800	20% Discount to BIS
12(Resistance to Flame and Ignition)	-	2000	20% Discount to BIS
13(Fault conditions)	-	5000	20% Discount to BIS
14(Creepage distance and clearances)	-	1800	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

For rated voltage up to 250V AC, 50 Hz and rated wattage up to 35 W. • Restricted to Cap type B22d, E14 & E27 only. Amendment No-3 including w.e.f. 06.03.2024 (rating upto 35 watt)

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

Size: 1-400 sqmm

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1( Cables for Fixed Installation)	-	200	-
Cl.5( INSULATION)	-	200	-
Cl. 6.1( Glass Tape)	-	200	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	200	-
Cl 6.4( Fire Barrier Tape)	-	200	-
Cl 7(CENTRE AND FILLERS)	-	200	-
Cl 7(CENTRE AND FILLERS)	-	200	-
Cl 7(CENTRE AND FILLERS)	-	200	-
Cl 7(CENTRE AND FILLERS)	-	200	-
Cl 8( ARMOUR)	-	200	-
Cl 9.1( Inner Sheath)	-	200	-
Cl 9.2( Outer Sheath)	-	200	-
Cl 10.1( CONDUCTORS)	-	200	-
Cl 10.2( CONDUCTORS)	-	200	-
Cl 11.1( INSULATION)	-	200	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	1000	-
Cl 12( CORE IDENTIFICATION)	-	200	-
Cl 13( LAYING UP OF CORES)	-	200	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	1000	-
Cl 15.1( ARMOURING)	-	200	-
Cl 15.3.1( Type of Armour)	-	200	-
Cl 15.3.2( Type of Armour)	-	200	-
Cl 15.3.3( ARMOURING)	-	200	-
Cl 15.3.3( ARMOURING)	-	200	-
Cl 15.4.1( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 15.4.2( ARMOURING)	-	200	-
Cl 16.2( OUTER SHEATH)	-	200	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	1000	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	1000	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	1000	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	2000	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	2000	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Tensile strength variation)	-	2000	-
Cl 17.2(Elongation Variation)	-	2000	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	2000	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	2000	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	2000	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	2000	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	2000	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	2000	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	2000	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	2000	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	2000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	10000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	10000	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	8000	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	8000	-
Cl 19.1( Manufacturer’s Identification)	-	200	-
Cl 19.2( Voltage Identification)	-	200	-
Cl 19.3( Cable Identification)	-	200	-
Cl 19.4( Cable Code)	-	200	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 02.01.2024 Size: 1 to 400 sqmm

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

Size: 1.5 to 630 sqmm

160000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	3000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2500	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	2000	-
IS 191:2007 & IS 440(Copper purity test)	-	5000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	4000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	4000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	4000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	3000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	4000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	4000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	4000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	4000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	4000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	2000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	4000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	4000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	4000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	4000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	2000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	4000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	4000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	4000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	4000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	4000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	2000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	4000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	4000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	4000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	4000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	4000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	4000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	4000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	4000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	4000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	4000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	4000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	4000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	4000	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 20.12.2023. Size: 1.5 to 630 sqmm.

IS 9968 : Part 2 (2002)

Specification for elastomer - Insulated cables: Part 2 for working voltages from 3.3 kV up to and including 33 kV (First Revision)

Size: 16 to 630 sqmm

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTORS: Cables for Fixed Installation)	-	200	-
4.2(CONDUCTORS:Flexible Cables)	-	200	-
5(INSULATION)	-	200	-
6(SEMICONDUCTING COMPOUND)	-	200	-
7.1(Proofed Tape)	-	200	-
7.1(Proofed Tape: Thickness)	-	200	-
7.2(Polyethylene Terephthalate ( P E T P ) or Polypropylene Base Tape : Thickness)	-	200	-
7.3(Tape )	-	200	-
8(SCREENING)	-	200	-
9(CENTRE AND FILLERS)	-	200	-
10(ARMOUR)	-	200	-
11.1(Inner Sheath)	-	200	-
11.2(Outer Sheath)	-	200	-
12.1(Tapes)	-	200	-
12.2(Cords and Yarns)	-	200	-
13.1 & 13.2(CONSTRUCTION:CONDUCTORS-Cables for Fixed Installations/Flexible Cables)	-	200	-
13.3(Earthing Conductor)	-	200	-
13.3.1(Earthing Conductor)	-	200	-
13.4(Separator Tape)	-	200	-
14(CONDUCTOR SCREENING)	-	200	-
15.1(INSULATION : Application)	-	200	-
15.2(Thickness of Insulation)	-	1000	-
15.3(Tolerance on Thickness of Insulation)	-	1000	-
16.1(INSULATION SCREENING : Application)	-	200	-
16.2(INSULATION SCREENING : Parts )	-	200	-
16.3(INSULATION SCREENING : Non Metallic Parts )	-	200	-
16.4(INSULATION SCREENING : Metallic Parts )	-	200	-
17(CORE IDENTIFICATION)	-	200	-
17(CORE IDENTIFICATION: Unscreed cable )	-	200	-
18.1(LAYING UP OF CORES)	-	200	-
18.2(LAYING UP OF CORES : Flexible cable)	-	200	-
18.3(LAYING UP OF CORES : Binder Tape)	-	200	-
19.1(Inner Sheath : Application)	-	200	-
19.2(Thickness of Inner Sheath)	-	1000	-
19.3(Inner Sheath : proofed tape)	-	200	-
20.1(ARMOURING: Application)	-	200	-
20.2(Type of Armour)	-	200	-
20.2 1.2(Direction of lay of armour)	-	200	-
20.2 1.3(Joint in armour)	-	200	-
20.2.2(Filling Factot )	-	200	-
20.2.2(Diameter of braiding)	-	200	-
20.2.2.1(Braiding material)	-	200	-
20.3(Substitution of the galvanized steel wires/formed)	-	200	-
21.1(OUTER SHEATH)	-	200	-
21.2(Coulor of Outer sheath)	-	200	-
21.3(Thickness of Outer Sheat: Average)	-	1000	-
21.3(Thickness of Outer Sheat: Minimum)	-	1000	-
22.1 a)1)(Annealing test (for copper) - IS 10810: Part 1)	-	500	-
22.1 a)2)(Tensile test (for aluminium) -IS 10810: Part 2)	-	1000	-
22.1 a)3)(Wrapping Test (for aluminium) - IS 10810: Part 3)	-	1000	-
22.1 a)4)(Conductor resistance test)	-	1000	-
22.1 a)5)(Persulphate test (tinned copper conductor)- IS 10810: Part 4)	-	1000	-
22.1 b)1)(Test for Galvanized Steel Wires/Formed Wires 1) Dimensions -IS 10810: Part 36)	-	1000	-
22.1 b)2)i)(Test for Galvanized Steel Wires/Formed Wires 2) Tensile Strentgh -IS 10810: Part 37)	-	1000	-
22.1 b)2)ii)(Test for Galvanized Steel Wires/Formed Wires 2) Elongation at break -IS 10810: Part 37)	-	1000	-
22.1 b)2)iii)(Test for Galvanized Steel Wires/Formed Wires 3) Torsion (for round wires only) -IS 10810: Part 38)	-	1000	-
22.1 b)2)iv)(Test for Galvanized Steel Wires/Formed Wires 4) Winding (for strips only) -IS 10810: Part 39)	-	1000	-
22.1 b)2)v)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Uniformity-IS 10810: Part 40)	-	1000	-
22.1 b)2)vi)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Mass -IS 10810: Part 41)	-	1000	-
22.1 b)2) vii) (Resistivity - IS 10810: Part 42)	-	1000	-
22.1 c)2)(Physical Tests for Insulation : Tensile Strenth - IS 10810: Part 7)	-	1000	-
22.1 c)2)(Physical Tests for Insulation : Elongation - IS 10810: Part 7)	-	1000	-
22.1 c)2)(Physical Tests for Sheath : Tensile Strenth - IS 10810: Part 7)	-	1000	-
22.1 c)2)(Physical Tests for Sheath : Elongation - IS 10810: Part 7)	-	1000	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth - IS 10810: Part 11)	-	1000	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth Variation - IS 10810: Part 12)	-	1000	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation - IS 10810: Part 11)	-	1000	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation variation - IS 10810: Part 12)	-	1000	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth - IS 10810: Part 11)	-	1000	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth variation - IS 10810: Part 12)	-	1000	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation - IS 10810: Part 11)	-	1000	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation variation - IS 10810: Part 12)	-	1000	-
22.1 c)4)(Physical Tests for Insulation ( Ageing in air bomb): Tensile Strenth variation - IS 10810: Part 56)	-	1000	-
22.1 c)4)(Physical Tests for Insulation( Ageing in air bomb) : Elongation variation - IS 10810: Part 56)	-	1000	-
22.1 c)4)(Physical Tests for Sheath(Ageing in air bomb) : Tensile Strenth variation - IS 10810: Part 56)	-	1000	-
22.1 c)4)(Physical Tests for Sheath ( Ageing in air bomb): Elongation variation - IS 10810: Part 56)	-	1000	-
22.1 c)5)(Physical Tests for Insulation :Hot set Elongation - IS 10810: Part 30)	-	1500	-
22.1 c)5)(Physical Tests for Insulation :Permanent set - IS 10810: Part 30)	-	1500	-
22.1 c)5)(Physical Tests for Sheath :Hot set Elongation - IS 10810: Part 30)	-	1500	-
22.1 c)5)(Physical Tests for Sheath :Permanent set - IS 10810: Part 30)	-	1500	-
22.1 c)6)(Physical Tests for Sheath(Oil resistance test) : Tensile Strenth Variation - IS 10810: Part 31)	-	1500	-
22.1 c)6)(Physical Tests for Sheath ( Oil resistance test): Elongation Variation - IS 10810: Part 31)	-	1500	-
22.1 c)7)(Tear Resistance test - IS 10810: Part 17)	-	1500	-
22.1 c)8)(Shrinkage : Insulation - IS 10810: Part 12)	-	1500	-
22.1 c)8)(Shrinkage test- Crack observed : Insulation - IS 10810: Part 13)	-	1500	-
22.1 c)8)(Shrinkage test : Sheath - IS 10810: Part 12)	-	1500	-
22.1 c)8)(Shrinkage test - Crack oberved : Sheath - IS 10810: Part 13)	-	1500	-
22.1 c)9)(Hot deformation test : Insulation - IS 10810: Part 15)	-	1500	-
22.1 c)9)(Hot deformation test : Sheath - IS 10810: Part 15)	-	1500	-
22.1 c)10)(Loss of mass in air oven : Insulation - IS 10810: Part 10)	-	1500	-
22.1 c)10)(Loss of mass in air oven : Sheath - IS 10810: Part 10)	-	1500	-
22.1 c)11)(Heat shock : Insulation - IS 10810: Part 14)	-	1500	-
22.1 c)11)(Heat shock : Sheath - IS 10810: Part 14)	-	1500	-
22.1 c)12)(Thermal stability : Insulation - IS 10810: Part 60)	-	1500	-
22.1 c)12)(Thermal stability : Sheath - IS 10810: Part 60)	-	1500	-
22.1 d)(Insulation Resistance Test: Volume resistivity )	-	1500	-
22.1 d)(Insulation Resistance Test: Insulation resistance constant )	-	1500	-
22.1 e)(Partial Discharge Test)	-	35000	-
22.1 f)(Bending Test Followed by Partial Discharge Test)	-	25000	-
22.1 g)(Dielectric Power Factor Test 1) As a function of Voltage)	-	1000	-
22.1 g)(Dielectric Power Factor Test 1) As a function of temperature)	-	1000	-
22.1 h)(Heating Cycle Test)	-	25000	-
22.1 j)(Impulse Withstand Test)	-	25000	-
22.1 k)(High Voltage Test for Four Hours)	-	25000	-
22.1 m)(Water Absorption Test - IS 10810: Part 28)	-	1500	-
22.1 n)(Flammability)	-	5000	-
24.1(Manufacturer's Identification)	-	200	-
24.2(Voltage Identification)	-	200	-
24.3(Cable Code)	-	200	-
25.2.1(Marking on drum )	-	200	-
25.2.2(BIS Certification Marking)	-	200	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 20.12.2023. Size: 16 to 630 sqmm

IS 1554 : Part 2 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 2 for working voltages from 3.3 kV up to and including 11 kV (Second Revision)

Size: 25 to 630 sqmm

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	200	-
3.1.1(CONDUCTOR)	-	200	-
4.1(INSULATION)	-	200	-
5.1(SCREENING)	-	200	-
6.1(FILLERS AND INNER SHEATH)	-	500	-
6.2(FILLERS AND INNER SHEATH)	-	500	-
7.1(ARMOURING)	-	200	-
7.2(ARMOURING)	-	200	-
8.1(OUTER SHEATH)	-	200	-
9.1(CONDUCTOR)	-	200	-
9.2(CONDUCTOR)	-	200	-
10.1(CONDUCTOR SCREENING)	-	200	-
11.1(INSULATION)	-	200	-
11.2(INSULATION : Thickness of Insulation)	-	200	-
11.3(INSULATION : Tolerance on Thickness of Insulation)	-	200	-
11.4(INSULATION : Application of Insulation)	-	200	-
12.1(INSULATION SCREENING)	-	200	-
12.2(INSULATION SCREENING)	-	200	-
12.3(INSULATION SCREENING)	-	200	-
12.4(INSULATION SCREENING)	-	200	-
13.1(CORE IDENTIFICATION)	-	200	-
13.1.1(CORE IDENTIFICATION)	-	200	-
14.1(LAYING UP OF CORES)	-	200	-
15.1(INNER SHEATH (COMMON COVERING))	-	200	-
15.2(INNER SHEATH (COMMON COVERING))	-	200	-
15.3(INNER SHEATH (COMMON COVERING))	-	200	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
16.1.1(ARMOURING : Application)	-	200	-
16.1.2(ARMOURING : Application)	-	200	-
16.1.3(ARMOURING : Direction of lay )	-	200	-
16.1.4(ARMOURING : Application)	-	200	-
16.2.1(ARMOURING : Type of Armour)	-	200	-
16.2.2(ARMOURING : Type of Armour)	-	200	-
16.3(Armouring : Dimensions -Wire Diameter)	-	200	-
16.3(Armouring : Dimensions -Formed wire )	-	200	-
16.4(ARMOURING : Joints)	-	200	-
16.5(ARMOURING : Resistance)	-	200	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
17.1(OUTER SHEATH)	-	200	-
17.2(OUTER SHEATH : colour )	-	200	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	1000	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	500	-
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	1000	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	1000	-
18.1 a)4)(Resistance test - Neutral conductor )	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	1500	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1500	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage )	-	1500	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1500	-
18.1 d) 4)(Hot deformation : Insulation )	-	1500	-
18.1 d) 4)(Hot deformation : Sheath )	-	1500	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	1500	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	1500	-
18.1 d) 6)(Heat shock test- Insulation )	-	1500	-
18.1 d) 6)(Heat shock test- sheath )	-	1500	-
18.1 d) 7)(Thermal stability- insulation )	-	1500	-
18.1 d) 7)(Thermal stability- Sheath )	-	1500	-
18.1 d) 8)(Water absorption (gravimetric)(for insulation, where applicable))	-	1500	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	1500	-
18.1 e)(Insulation resistance test : IR Constant )	-	1500	-
19.2(Partial discharge test)	-	35000	-
19.3(Bending test)	-	1000	-
19.4(Dielectric power factor test)	-	1000	-
19.4(Dielectric power factor test)	-	1000	-
19.5(Heating cycle test)	-	25000	-
19.6(Impulse withstand test)	-	25000	-
19.7(High voltage test)	-	25000	-
19.8(Flammability test)	-	5000	-
19.9(Oxygen Index Test)	-	5000	-
19.10(Flame Retardance Test on Single Cables)	-	5000	-
19.11(Flame Retardance Test on Bunched Cables)	-	8000	-
19.13(Test for Halogen Acid Gas Evolution)	-	8000	-
19.14(Temperature Index)	-	5000	-
18.4(Optional Test : Cold Impact )	-	3000	-
20.1(IDENTIFICATION : Manufacturer's Identification)	-	200	-
20.2(IDENTIFICATION : Cable Identification)	-	200	-
20.3(IDENTIFICATION : Cable Code)	-	200	-
5.1.1(Non-magnetic Metallic Tape for SingleCore Unscreened and Unarmoured Cables)	-	200	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 20.12.2023. Size: 25 to 630 sqmm

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

Size: 95-630 sqmm

550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	1000	-
7.1(MOISTURE BARRIER : Laminated Tape)	-	1000	-
7.2(MOISTURE BARRIER : Lead Alloy Sheath)	-	1000	-
7.3(MOISTURE BARRIER : Water Blocking Tape/Powder)	-	1000	-
8.1(INNER SHEATH)	-	1000	-
8.2(INNER SHEATH)	-	1000	-
8.3(INNER SHEATH)	-	1000	-
9.1(ARMOUR)	-	1000	-
9.2(ARMOUR)	-	1000	-
10.1(OUTER SHEATH)	-	1000	-
10.2(OUTER SHEATH)	-	1000	-
11.1(CONDUCTOR)	-	1000	-
11.2(CONDUCTOR)	-	1000	-
12.1(CONDUCTOR SCREENING )	-	1000	-
12.2(CONDUCTOR SCREENING )	-	1000	-
13.1(INSULATION)	-	1000	-
13.2(INSULATION)	-	1000	-
14.1(INSULATION SCREENING)	-	1000	-
14.2.1(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.2(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.3(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.3.1(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.2(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.3(INSULATION SCREENING : Metallic Part)	-	1000	-
15.1(MOISTURE BARRIER)	-	1000	-
15.2.1(Metallic Sheath)	-	1000	-
15.2.2(Metallic Sheath)	-	1000	-
16.1(INNER SHEATH)	-	1000	-
16.2(INNER SHEATH)	-	1000	-
17.1(ARMOUR)	-	1000	-
17.2(ARMOUR)	-	1000	-
17.3(ARMOUR)	-	1000	-
17.4(ARMOUR)	-	1000	-
17.5(ARMOUR)	-	1000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(outer sheath colour)	-	1000	-
18.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	2500	-
18.3.1(Thickness of Outer Sheath : armoured Cables)	-	2500	-
19.1 A) I)(Tests on conductor : Annealing test ( for copper ))	-	2500	-
19.1 A) II)(Tests on conductor : Resistance test)	-	5000	-
19.1 b) I)(Test for thickness and dimensions of insulation)	-	5000	-
19.1 b) II)(Tensile strength and elongation at break)	-	5000	-
19.1 b) III)(Thermal ageing in air oven)	-	5000	-
19.1 b) IV)(Hot set test)	-	5000	-
19.1 b) V)(Shrinkage test)	-	5000	-
20.3(Test for concentric metallic screen : Test for concentric copper wire)	-	5000	-
20.4(Test for concentric copper tape)	-	5000	-
20.5(Thickness of metallic sheath)	-	5000	-
20.6(Tests for armouring material : Dimensions)	-	5000	-
19.1 f) II)(Tests for armouring material : Tensile strength and elongation at break)	-	5000	-
Table 9, (Measurement of thickness)	-	5000	-
19.1 g)2) i)(PVC sheath : Tensile strength and elongation at break)	-	5000	-
19.1 g)2) iii)(PVC sheath : Loss of mass)	-	5000	-
19.1 g)2) v)(PVC sheath : Hot deformation test)	-	5000	-
19.1 g)2) vi)(PVC sheath : Shrinkage test)	-	5000	-
19.1 g)2) vii)(PVC sheath : Thermal stability)	-	5000	-
19.1 g)3) ii)(PE sheath : Tensile strength and elongation at break before and after ageing)	-	5000	-
19.1 g)3) iii)(PE sheath : Hot-detormation)	-	5000	-
20.7(Flammabihty test ( for PVC outer sheathed cables only ))	-	8000	-
20.8.3(Water tightness test)	-	8000	-
20.9.1(Thermal ageing on complete cable sample)	-	8000	-
19.1 k) ii)(Tensile strength and elongation at breakfor insulation and outer sheath)	-	5000	-
20.2(Resistivity test for semi-conducting layer)	-	5000	-
20.11.1(Bending test followed by P D test)	-	70000	-
20.12, 20.18(Dielectric power factor and capacitance measurement at ambient temperature)	-	5000	-
20.13(Dielectric power factor measurement at elevated temperature)	-	5000	-
20.14.1(Load cycle test followed by P.D measurement)	-	70000	-
20.15(Impulse Voltage Test Followed by High Voltage Test)	-	50000	-
19.5(Check on Insulation Thickness Before the Electrical Type Tests)	-	5000	-
20.16.1(Test for Dimensions of Insulation : Insulation Thickness)	-	5000	-
20.16.2(Test for Dimensions of Insulation : Test for Eccentricity)	-	5000	-
20.16.3(Test for Dimensions of Insulation : Test for Ovality)	-	5000	-
20.17(High Voltage Test ( as Routine and Acceptance Tests ) )	-	50000	-
20.18(Measurement of Capacitance)	-	5000	-
4.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	1000	-
7.1(MOISTURE BARRIER : Laminated Tape)	-	1000	-
7.2(MOISTURE BARRIER : Lead Alloy Sheath)	-	1000	-
7.3(MOISTURE BARRIER : Water Blocking Tape/Powder)	-	1000	-
8.1(INNER SHEATH)	-	1000	-
8.2(INNER SHEATH)	-	1000	-
8.3(INNER SHEATH)	-	1000	-
9.1(ARMOUR)	-	1000	-
9.2(ARMOUR)	-	1000	-
10.1(OUTER SHEATH)	-	1000	-
10.2(OUTER SHEATH)	-	1000	-
11.1(CONDUCTOR)	-	1000	-
11.2(CONDUCTOR)	-	1000	-
12.1(CONDUCTOR SCREENING )	-	1000	-
12.2(CONDUCTOR SCREENING )	-	1000	-
13.1(INSULATION)	-	1000	-
13.2(INSULATION)	-	1000	-
14.1(INSULATION SCREENING)	-	1000	-
14.2.1(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.2(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.3(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.3.1(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.2(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.3(INSULATION SCREENING : Metallic Part)	-	1000	-
15.1(MOISTURE BARRIER)	-	1000	-
15.2.1(Metallic Sheath)	-	1000	-
15.2.2(Metallic Sheath)	-	1000	-
16.1(INNER SHEATH)	-	1000	-
16.2(INNER SHEATH)	-	1000	-
17.1(ARMOUR)	-	1000	-
17.2(ARMOUR)	-	1000	-
17.3(ARMOUR)	-	1000	-
17.4(ARMOUR)	-	1000	-
17.5(ARMOUR)	-	1000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(outer sheath colour)	-	1000	-
18.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	2500	-
18.3.1(Thickness of Outer Sheath : armoured Cables)	-	2500	-
19.1 A) I)(Tests on conductor : Annealing test ( for copper ))	-	2500	-
19.1 A) II)(Tests on conductor : Resistance test)	-	5000	-
19.1 b) I)(Test for thickness and dimensions of insulation)	-	5000	-
19.1 b) II)(Tensile strength and elongation at break)	-	5000	-
19.1 b) III)(Thermal ageing in air oven)	-	5000	-
19.1 b) IV)(Hot set test)	-	5000	-
19.1 b) V)(Shrinkage test)	-	5000	-
20.3(Test for concentric metallic screen : Test for concentric copper wire)	-	5000	-
20.4(Test for concentric copper tape)	-	5000	-
20.5(Thickness of metallic sheath)	-	5000	-
20.6(Tests for armouring material : Dimensions)	-	5000	-
19.1 f) II)(Tests for armouring material : Tensile strength and elongation at break)	-	5000	-
Table 9, (Measurement of thickness)	-	5000	-
19.1 g)2) i)(PVC sheath : Tensile strength and elongation at break)	-	5000	-
19.1 g)2) iii)(PVC sheath : Loss of mass)	-	5000	-
19.1 g)2) v)(PVC sheath : Hot deformation test)	-	5000	-
19.1 g)2) vi)(PVC sheath : Shrinkage test)	-	5000	-
19.1 g)2) vii)(PVC sheath : Thermal stability)	-	5000	-
19.1 g)3) ii)(PE sheath : Tensile strength and elongation at break before and after ageing)	-	5000	-
19.1 g)3) iii)(PE sheath : Hot-detormation)	-	5000	-
20.7(Flammabihty test ( for PVC outer sheathed cables only ))	-	8000	-
20.8.3(Water tightness test)	-	8000	-
20.9.1(Thermal ageing on complete cable sample)	-	8000	-
19.1 k) ii)(Tensile strength and elongation at breakfor insulation and outer sheath)	-	5000	-
20.2(Resistivity test for semi-conducting layer)	-	5000	-
20.11.1(Bending test followed by P D test)	-	70000	-
20.12, 20.18(Dielectric power factor and capacitance measurement at ambient temperature)	-	5000	-
20.13(Dielectric power factor measurement at elevated temperature)	-	5000	-
20.14.1(Load cycle test followed by P.D measurement)	-	70000	-
20.15(Impulse Voltage Test Followed by High Voltage Test)	-	50000	-
19.5(Check on Insulation Thickness Before the Electrical Type Tests)	-	5000	-
20.16.1(Test for Dimensions of Insulation : Insulation Thickness)	-	5000	-
20.16.2(Test for Dimensions of Insulation : Test for Eccentricity)	-	5000	-
20.16.3(Test for Dimensions of Insulation : Test for Ovality)	-	5000	-
20.17(High Voltage Test ( as Routine and Acceptance Tests ) )	-	50000	-
20.18(Measurement of Capacitance)	-	5000	-
4.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	1000	-
7.1(MOISTURE BARRIER : Laminated Tape)	-	1000	-
7.2(MOISTURE BARRIER : Lead Alloy Sheath)	-	1000	-
7.3(MOISTURE BARRIER : Water Blocking Tape/Powder)	-	1000	-
8.1(INNER SHEATH)	-	1000	-
8.2(INNER SHEATH)	-	1000	-
8.3(INNER SHEATH)	-	1000	-
9.1(ARMOUR)	-	1000	-
9.2(ARMOUR)	-	1000	-
10.1(OUTER SHEATH)	-	1000	-
10.2(OUTER SHEATH)	-	1000	-
11.1(CONDUCTOR)	-	1000	-
11.2(CONDUCTOR)	-	1000	-
12.1(CONDUCTOR SCREENING )	-	1000	-
12.2(CONDUCTOR SCREENING )	-	1000	-
13.1(INSULATION)	-	1000	-
13.2(INSULATION)	-	1000	-
14.1(INSULATION SCREENING)	-	1000	-
14.2.1(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.2(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.2.3(INSULATION SCREENING : Non-metallic Part)	-	1000	-
14.3.1(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.2(INSULATION SCREENING : Metallic Part)	-	1000	-
14.3.3(INSULATION SCREENING : Metallic Part)	-	1000	-
15.1(MOISTURE BARRIER)	-	1000	-
15.2.1(Metallic Sheath)	-	1000	-
15.2.2(Metallic Sheath)	-	1000	-
16.1(INNER SHEATH)	-	1000	-
16.2(INNER SHEATH)	-	1000	-
17.1(ARMOUR)	-	1000	-
17.2(ARMOUR)	-	1000	-
17.3(ARMOUR)	-	1000	-
17.4(ARMOUR)	-	1000	-
17.5(ARMOUR)	-	1000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(outer sheath colour)	-	1000	-
18.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	5000	-
18.3.1(Thickness of Outer Sheath : armoured Cables)	-	5000	-
19.1 A) I)(Tests on conductor : Annealing test ( for copper ))	-	5000	-
19.1 A) II)(Tests on conductor : Resistance test)	-	5000	-
19.1 b) I)(Test for thickness and dimensions of insulation)	-	5000	-
19.1 b) II)(Tensile strength and elongation at break)	-	5000	-
19.1 b) III)(Thermal ageing in air oven)	-	5000	-
19.1 b) IV)(Hot set test)	-	5000	-
19.1 b) V)(Shrinkage test)	-	5000	-
20.3(Test for concentric metallic screen : Test for concentric copper wire)	-	5000	-
20.4(Test for concentric copper tape)	-	5000	-
20.5(Thickness of metallic sheath)	-	5000	-
20.6(Tests for armouring material : Dimensions)	-	5000	-
19.1 f) II)(Tests for armouring material : Tensile strength and elongation at break)	-	5000	-
Table 9, (Measurement of thickness)	-	5000	-
19.1 g)2) i)(PVC sheath : Tensile strength and elongation at break)	-	5000	-
19.1 g)2) iii)(PVC sheath : Loss of mass)	-	5000	-
19.1 g)2) v)(PVC sheath : Hot deformation test)	-	5000	-
19.1 g)2) vi)(PVC sheath : Shrinkage test)	-	5000	-
19.1 g)2) vii)(PVC sheath : Thermal stability)	-	5000	-
19.1 g)3) ii)(PE sheath : Tensile strength and elongation at break before and after ageing)	-	5000	-
19.1 g)3) iii)(PE sheath : Hot-detormation)	-	5000	-
20.7(Flammabihty test ( for PVC outer sheathed cables only ))	-	15000	-
20.8.3(Water tightness test)	-	10000	-
20.9.1(Thermal ageing on complete cable sample)	-	8000	-
19.1 k) ii)(Tensile strength and elongation at breakfor insulation and outer sheath)	-	5000	-
20.2(Resistivity test for semi-conducting layer)	-	5000	-
20.11.1(Bending test followed by P D test)	-	95000	-
20.12, 20.18(Dielectric power factor and capacitance measurement at ambient temperature)	-	8000	-
20.13(Dielectric power factor measurement at elevated temperature)	-	8000	-
20.14.1(Load cycle test followed by P.D measurement)	-	95000	-
20.15(Impulse Voltage Test Followed by High Voltage Test)	-	70000	-
19.5(Check on Insulation Thickness Before the Electrical Type Tests)	-	5000	-
20.16.1(Test for Dimensions of Insulation : Insulation Thickness)	-	5000	-
20.16.2(Test for Dimensions of Insulation : Test for Eccentricity)	-	5000	-
20.16.3(Test for Dimensions of Insulation : Test for Ovality)	-	5000	-
20.17(High Voltage Test ( as Routine and Acceptance Tests ) )	-	70000	-
20.18(Measurement of Capacitance)	-	5000	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 02.01.2024 Size: 95 to 630 sqmm

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Size: 25 to 630 sqmm

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	200	-
4.1.1(CONDUCTOR)	-	200	-
5(INSULATION)	-	200	-
6(SCREENING)	-	200	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	200	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	200	-
7(FILLERS AND INNER SHEATH)	-	500	-
8.1(ARMOURING)	-	200	-
8.2(ARMOURING)	-	200	-
9(OUTER SHEATH )	-	200	-
10.1(CONDUCTOR)	-	200	-
10.2(CONDUCTOR)	-	200	-
11(CONDUCTOR SCREENING)	-	200	-
12.1(INSULATION)	-	200	-
12.2(INSULATION : Thickness of Insulation)	-	200	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	200	-
12.4(Eccentricity and Ovality)	-	200	-
12.5(INSULATION : Application of Insulation)	-	200	-
13.1(INSULATION SCREENING)	-	200	-
13.2(INSULATION SCREENING)	-	200	-
13.3(INSULATION SCREENING)	-	200	-
13.4(INSULATION SCREENING)	-	200	-
14.1(CORE IDENTIFICATION)	-	200	-
14.1.1(CORE IDENTIFICATION)	-	200	-
15.1(LAVING UP OF CORES)	-	200	-
16.1(INNER SHEATH (COMMON COVERING))	-	200	-
16.2(INNER SHEATH (COMMON COVERING))	-	200	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	200	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
17.1(ARMOURING : Application )	-	200	-
17.1.1(ARMOURING )	-	200	-
17.1.2(ARMOURING )	-	200	-
17.1.3(ARMOURING )	-	200	-
17.2(ARMOURING : Type of armour )	-	200	-
17.2.1(ARMOURING : Type of armour )	-	200	-
17.2(ARMOURING : Coverage )	-	200	-
17.3(ARMOURING : Dimension )	-	200	-
17.4(ARMOURING : Joints)	-	200	-
16.4(ARMOURING : Resistance)	-	200	-
18.1(OUTER SHEATH)	-	200	-
18.2(OUTER SHEATH: Colour)	-	200	-
18.3(Thicknes of outer sheath : average )	-	200	-
18.3(Thicknes of outer sheath : minimum )	-	200	-
19.1 i) a)(Annealing test (for copper))	-	500	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	1000	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	1000	-
19.1 i) c)(Wrapping test ( for aluminium))	-	1000	-
19.1 i) d)(Resistance test - Main conductor )	-	1000	-
19.1 i) d)(Resistance test - Neutral conductor )	-	1000	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	1000	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	1000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
19.1 iii) c)(Degree of cross linking )	-	1000	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	1000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	1000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	1000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	2500	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	1000	-
19.1 v) b)(Volume resistivity)	-	1500	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	1500	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	1500	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1500	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1500	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	1500	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1500	-
19.1 vi) d)(Sheath : Hot deformation)	-	1500	-
19.1 vi) e)(Loss of massIn air oven)	-	1500	-
19.1 vi) f)(Sheath : Heat shock test)	-	1500	-
19.1 vi) g)(Sheath : Thermalstability)	-	1500	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	1500	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	1500	-
20.2(Partial discharge test)	-	35000	-
20.3(Bending test)	-	1000	-
20.4(Dielectric power factor test : As a function of voltage)	-	1000	-
20.4(Dielectric power factor test : As a function of temperature)	-	1000	-
20.5(Heating Cycle Test)	-	25000	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	25000	-
20.7(High voltage test)	-	25000	-
20.8(Flammability test)	-	5000	-
20.1(Oxygen Index Test)	-	5000	-
20.11(Flame Retardance Test on Single Cables)	-	5000	-
20.12(Flame Retardance Test on Bunched Cables)	-	8000	-
20.13(Test for Halogen Acid Gas Evolution)	-	8000	-
20.14( Test for Smoke Density)	-	5000	-
20.15(Temperature Index)	-	5000	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	200	-
21.2(IDENTIFICATION : Cable Identification)	-	200	-
21.3(IDENTIFICATION : Cable Code)	-	200	-
20.3 (a)(Partial discharge test (Bending test))	-	35000	-
20.5 (a)(PD test (heating cycle test))	-	35000	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	25000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-
4.1(CONDUCTOR)	-	200	-
4.1.1(CONDUCTOR)	-	200	-
5(INSULATION)	-	200	-
6(SCREENING)	-	200	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	200	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	200	-
7(FILLERS AND INNER SHEATH)	-	500	-
8.1(ARMOURING)	-	200	-
8.2(ARMOURING)	-	200	-
9(OUTER SHEATH )	-	200	-
10.1(CONDUCTOR)	-	200	-
10.2(CONDUCTOR)	-	200	-
11(CONDUCTOR SCREENING)	-	200	-
12.1(INSULATION)	-	200	-
12.2(INSULATION : Thickness of Insulation)	-	200	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	200	-
12.4(Eccentricity and Ovality)	-	200	-
12.5(INSULATION : Application of Insulation)	-	200	-
13.1(INSULATION SCREENING)	-	200	-
13.2(INSULATION SCREENING)	-	200	-
13.3(INSULATION SCREENING)	-	200	-
13.4(INSULATION SCREENING)	-	200	-
14.1(CORE IDENTIFICATION)	-	200	-
14.1.1(CORE IDENTIFICATION)	-	200	-
15.1(LAVING UP OF CORES)	-	200	-
16.1(INNER SHEATH (COMMON COVERING))	-	200	-
16.2(INNER SHEATH (COMMON COVERING))	-	200	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	200	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	200	-
17.1(ARMOURING : Application )	-	200	-
17.1.1(ARMOURING )	-	200	-
17.1.2(ARMOURING )	-	200	-
17.1.3(ARMOURING )	-	200	-
17.2(ARMOURING : Type of armour )	-	200	-
17.2.1(ARMOURING : Type of armour )	-	200	-
17.2(ARMOURING : Coverage )	-	200	-
17.3(ARMOURING : Dimension )	-	200	-
17.4(ARMOURING : Joints)	-	200	-
16.4(ARMOURING : Resistance)	-	200	-
18.1(OUTER SHEATH)	-	200	-
18.2(OUTER SHEATH: Colour)	-	200	-
18.3(Thicknes of outer sheath : average )	-	200	-
18.3(Thicknes of outer sheath : minimum )	-	200	-
19.1 i) a)(Annealing test (for copper))	-	500	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	1000	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	1000	-
19.1 i) c)(Wrapping test ( for aluminium))	-	1000	-
19.1 i) d)(Resistance test - Main conductor )	-	1000	-
19.1 i) d)(Resistance test - Neutral conductor )	-	1000	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	1000	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	1000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
19.1 iii) c)(Degree of cross linking )	-	1000	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	1000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	1000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	1000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	2500	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	1000	-
19.1 v) b)(Volume resistivity)	-	1500	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	1500	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	1500	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1500	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1500	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	1500	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1500	-
19.1 vi) d)(Sheath : Hot deformation)	-	1500	-
19.1 vi) e)(Loss of massIn air oven)	-	1500	-
19.1 vi) f)(Sheath : Heat shock test)	-	1500	-
19.1 vi) g)(Sheath : Thermalstability)	-	1500	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	1500	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	1500	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	1500	-
20.2(Partial discharge test)	-	35000	-
20.3(Bending test)	-	1000	-
20.4(Dielectric power factor test : As a function of voltage)	-	1000	-
20.4(Dielectric power factor test : As a function of temperature)	-	1000	-
20.5(Heating Cycle Test)	-	25000	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	25000	-
20.7(High voltage test)	-	25000	-
20.8(Flammability test)	-	5000	-
20.1(Oxygen Index Test)	-	5000	-
20.11(Flame Retardance Test on Single Cables)	-	5000	-
20.12(Flame Retardance Test on Bunched Cables)	-	8000	-
20.13(Test for Halogen Acid Gas Evolution)	-	8000	-
20.14( Test for Smoke Density)	-	5000	-
20.15(Temperature Index)	-	5000	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	200	-
21.2(IDENTIFICATION : Cable Identification)	-	200	-
21.3(IDENTIFICATION : Cable Code)	-	200	-
20.3 (a)(Partial discharge test (Bending test))	-	35000	-
20.5 (a)(PD test (heating cycle test))	-	35000	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	25000	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	25000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 02.01.2024 Size: 25 to 630 sqmm

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

Size: 0.5-630 sqmm

160000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	500	-
4.1.1 b) (Material : Seperator tape )	-	500	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	500	-
4.1.1 e) (Shape of conductor )	-	500	-
4.1.1 f) (Nominal size of conductor )	-	500	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	500	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	500	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	1000	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	1000	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1500	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1000	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	1500	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.3(Fillers)	-	500	-
4.4(Binder Tape)	-	500	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	500	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	500	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	1000	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1500	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1000	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	1500	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	1500	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	1500	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	500	-
4.5.6, 13.4(Colour of Sheath)	-	500	-
5.1(High Voltage Test (at Room Temperature))	-	15000	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	4000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	3000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	4000	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	4000	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	15000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	2000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	4000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	4000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	4000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	4000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	4000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	4000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	4000	-
6.1, Table 1(CORE IDENTIFICATION)	-	500	-
6.2(Core Identification by Numbers)	-	500	-
7.0(CABLE CODE)	-	500	-
9.0( IDENTIFICATION)	-	500	-
10.1(Packing )	-	500	-
10.2(marking)	-	500	-
10.2.1(Standards marking)	-	500	-
13.3, 14.3(assembly of cores )	-	500	-
6.1(General Requirements)	-	500	-
6.1.1(Colour Combination Green Yellow)	-	500	-
12.1(Conductor)	-	500	-
12.2, Table 4(insulation)	-	500	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	2000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	2000	-
4.3.1 (c)(Conductivity test (Fillers))	-	2000	-
4.3.1 (b)(pH test (Fillers))	-	2000	-
4.3.1 (a)(HCl test (Fillers))	-	2000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	2000	-
5.7 (b)(pH test (Assessment of halogen test))	-	2000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	2000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	2000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	2000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	3000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	6000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	6000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	5000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2500	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2500	-
6.1, Table 1(CORE IDENTIFICATION)	-	500	-
6.1(General Requirements)	-	500	-
6.1.1(Colour Combination Green Yellow)	-	50	-
12.1(Conductor)	-	500	-
12.2, Table 4(insulation)	-	500	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	2000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	2000	-
4.3.1 (c)(Conductivity test (Fillers))	-	2000	-
4.3.1 (b)(pH test (Fillers))	-	2000	-
4.3.1 (a)(HCl test (Fillers))	-	2000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	2000	-
5.7 (b)(pH test (Assessment of halogen test))	-	2000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	2000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	2000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	2000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	3000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	6000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	6000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	5000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2500	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2500	-

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 02.01.2024 Size: 0.5 to 630 sqmm

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Inputting of text)	-	4500	10% discount to BIS
5.2(Message Readability)	-	10000	10% discount to BIS
6(Marking)	-	500	10% discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Revised version of IS 16333(P-3):2022 Included w.e.f. 20.11.2023

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

Upto 16A

11850 View breakup
Rs.8800 for 6 A screw type; Rs.7350 for 6 A screwless type; Rs.8800/- for 10 A screw type; Rs.8800 for 10 A screwless type; Rs.9600/- for 16 screw type. Rs.11850/- for 16 screwless type.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating)	-	150	20% Discount for BIS
7(Classification)	-	150	20% Discount for BIS
8(Marking)	-	150	20% Discount for BIS
10(Protection against Electric Shock)	-	300	20% Discount for BIS
11.1(Provision for earthing)	-	300	20% Discount for BIS
11.2(Provision for earthing)	-	300	20% Discount for BIS
11.3(Provision for earthing)	-	300	20% Discount for BIS
11.4(Provision for earthing)	-	300	20% Discount for BIS
12.2(Terminals)	-	1000	20% Discount for BIS
12.3(Terminals)	-	1500	20% Discount for BIS
13(Constructional requirements )	-	800	20% Discount for BIS
14(Mechanism [Cl. 14])	-	350	20% Discount for BIS
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	500	20% Discount for BIS
15.2(b)Resistance to Harmful ingress of water [Cl. 15.2])	-	500	20% Discount for BIS
15.3(c) Resistance to Humidity [Cl. 15.3])	-	500	20% Discount for BIS
16(Insulation resistance and electric strength )	-	600	20% Discount for BIS
17(Temperature- rise [Cl. 17])	-	800	20% Discount for BIS
18(Marking and breaking Capacity[Cl. 18])	-	1500	20% Discount for BIS
19(Normal Operation [Cl. 19] a) General & Operation)	-	3000	20% Discount for BIS
20(Mechanical Strength Test [Cl. 20])	-	300	20% Discount for BIS
21(Resistance to Heat [Cl.21])	-	500	20% Discount for BIS
22(Screw, Current Carrying Part And Connection [Cl.22])	-	350	20% Discount for BIS
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	350	20% Discount for BIS
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	400	20% Discount for BIS
24.2(Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-	400	20% Discount for BIS
25 of IS 3854 : 1997(Resistance to rusting)	-	350	20% Discount for BIS
6(Rating)	-	150	20% Discount for BIS
7(Classification)	-	150	20% Discount for BIS
8(Marking)	-	150	20% Discount for BIS
10(Protection against Electric Shock)	-	300	20% Discount for BIS
11.1(Provision for earthing)	-	300	20% Discount for BIS
11.2(Provision for earthing)	-	300	20% Discount for BIS
11.3(Provision for earthing)	-	300	20% Discount for BIS
11.4(Provision for earthing)	-	300	20% Discount for BIS
12.2(Terminals)	-	1000	20% Discount for BIS
12.3(Terminals)	-	1500	20% Discount for BIS
13(Constructional requirements )	-	800	20% Discount for BIS
14(Mechanism [Cl. 14])	-	350	20% Discount for BIS
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	500	20% Discount for BIS
15.2(b)Resistance to Harmful ingress of water [Cl. 15.2])	-	500	20% Discount for BIS
15.3(c) Resistance to Humidity [Cl. 15.3])	-	500	20% Discount for BIS
16(Insulation resistance and electric strength )	-	600	20% Discount for BIS
17(Temperature- rise [Cl. 17])	-	800	20% Discount for BIS
18(Marking and breaking Capacity[Cl. 18])	-	1500	20% Discount for BIS
19(Normal Operation [Cl. 19] a) General & Operation)	-	3000	20% Discount for BIS
20(Mechanical Strength Test [Cl. 20])	-	300	20% Discount for BIS
21(Resistance to Heat [Cl.21])	-	500	20% Discount for BIS
22(Screw, Current Carrying Part And Connection [Cl.22])	-	350	20% Discount for BIS
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	350	20% Discount for BIS
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	400	20% Discount for BIS
24.2(Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-	400	20% Discount for BIS
25 of IS 3854 : 1997(Resistance to rusting)	-	350	20% Discount for BIS

Complete

19 Jul, 2024

06 Jun, 2027

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	20% Discount to BIS
8(Protection against accidental contact with live parts)	-	2150	20% Discount to BIS
9(Terminals)	-	6650	20% Discount to BIS
10(PROVISION FOR EARTHING)	-	2250	20% Discount to BIS
11(MOISTURE RESISTANCE)	-	5600	20% Discount to BIS
12(Electric Strength)	-	3600	20% Discount to BIS
14(Fault conditions)	-	8100	20% Discount to BIS
15(Transformer heating)	-	6550	20% Discount to BIS
16(Construction)	-	1500	20% Discount to BIS
17(Creepage distance and clearances)	-	3150	20% Discount to BIS
18(Screws, current carrying parts and connections)	-	1900	20% Discount to BIS
19(Resistance to heat, fire and tracking)	-	5250	20% Discount to BIS
20(Resistance to corrosion)	-	2000	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Up to 300V AC, 50Hz and 150V DC. Excluding: Components (Annex-1)

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

50000 View breakup
Rs.50,000/- [10% discount to BIS]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Marking)	-	1800	20 % Discount to BIS
7.0(Construction)	-	17160	20 % Discount to BIS
8.0(Creepage Distance and Clearances)	-	4080	20 % Discount to BIS
9.0(Provision for earthing)	-	6000	20 % Discount to BIS
10.0(Terminals)	-	2580	20 % Discount to BIS
11.0(External & Internal Wiring)	-	1800	20 % Discount to BIS
12.0(Protection against electric shock)	-	1260	20 % Discount to BIS
13.0(Endurance Tests and Thermal Tests)	-	8760	20 % Discount to BIS
14.0(Resistance to Dust & Moisture)	-	7920	20 % Discount to BIS
15.0(Insulation Resistance and Electric Strength)	-	1920	20 % Discount to BIS
16.0(Resistance to Heat , fire and tracking)	-	6720	20 % Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Up to & including 300V AC, 50Hz and 150V DC. Excluding: UV Radiation (Cl.4.24, Annex-P), Photometric test (Cl.17).

IS 9857 (1990)

Welding cables - Specification (First Revision)

16000 View breakup
SE 1 Covering Cable Rs. 13500.00 SE 3 Covering Cable Rs. 15000.00 Copper Conductor (Extra Charges For Static Flexibility Test) Rs. 900.00 Separated Wire Before Stranding (If Provided) Rs. 900.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	625	20% Discount to BIS
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	625	20% Discount to BIS
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	625	20% Discount to BIS
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	625	20% Discount to BIS
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	3750	20% Discount to BIS
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	3125	20% Discount to BIS
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2500	20% Discount to BIS
10.1 c) 5)(Hot set test )	-	2500	20% Discount to BIS
11.1(High Voltage Test ( Water Immersion Test ))	-	1875	20% Discount to BIS
11.3(Static Flexibility Test)	-	625	20% Discount to BIS
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	-	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	-	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	-	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	-	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	-	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	-	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	-	-
10.1 c) 5)(Hot set test )	-	-	-
11.1(High Voltage Test ( Water Immersion Test ))	-	-	-
11.3(Static Flexibility Test)	-	-	-

Complete

19 Jul, 2024

06 Jun, 2027

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Construction, Cl. 8 of IS 9537-1)	-	250	20% Discount to BIS
8.2(Construction, IS 9537-2)	-	250	20% Discount to BIS
6.1(Marking, IS 9537-2)	-	200	20% Discount to BIS
6.2(Marking, IS 9537-2)	-	200	20% Discount to BIS
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	100	20% Discount to BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	20% Discount to BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	500	20% Discount to BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500	20% Discount to BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	500	20% Discount to BIS
7.4(Screw threads, IS 9537-2)	-	500	20% Discount to BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1500	20% Discount to BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1000	20% Discount to BIS
13(External Influences, IS 9537-2)	-	4000	20% Discount to BIS
6.1(Marking, IS 9537-2)	-	0	price in above

Complete

19 Jul, 2024

06 Jun, 2027

INCLUDED W.E.F. 23-09-2020. For sizes 20mm to 50mm.

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

22950 View breakup
Single Core For General Services = 22950 /- Single Core For Heat Resisting Insulation = 22950 /- Single Core For Silicon Insulation = 22950 /- Single Core Sheathed Cable, General Services =22950.00 Single Core Sheathed Cable For Heat Resisting Insulation = 22950 /- Separated Wire Before Stranding (If Provided = 625.00) Each Additional Per Core Charge = 2500.00/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(CORE IDENTiFICATlON)	-	0	nil
12.2(Insulation : Thickness of Insufatien)	-	325	20% Discount to BIS
19.2(Sheath : Thickness of Sheath)	-	300	20% Discount to BIS
20( Overall diameter)	-	625	20% Discount to BIS
21. (a)(Persulphate tests (for copper))	-	1250	20% Discount to BIS
21. (b)(Annealing Test (for coper))	-	625	20% Discount to BIS
21. (c)( Tensile Test (for aluminium))	-	625	20% Discount to BIS
21. (d)( Wrapping Test (for aluminium))	-	625	20% Discount to BIS
21. (e)(Conductor Resistance )	-	625	20% Discount to BIS
21.1( Tensile strength )	-	625	20% Discount to BIS
22.1( Elongation)	-	625	20% Discount to BIS
21.1(type test : Ageing In air oven)	-	3125	20% Discount to BIS
21.1(type test : Ageing in air bomb)	-	3750	20% Discount to BIS
21.1(type test : Ageing In oxygen bomb)	-	3750	20% Discount to BIS
21.1(type test : Tear resistance )	-	1875	20% Discount to BIS
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	1875	20% Discount to BIS
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	1250	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

INCLUDED W.E.F. 23-09-2020.

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

8900 View breakup
For 3 Strands Rs. 1225.00 For 7 Strands Rs. 2500.00 For 19 Strands Rs. 3750.00 For 37 Strands Rs. 5750.00 For 61 Strands Rs. 7400.00 Separated Wire Before Stranding (If Provided) Rs. 1500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 Table-1(Dimensional measurement of wires)	-	1250	20% Discount to BIS
9.2 Table 3(Lay Ratio of stranded conductors)	-	1250	20% Discount to BIS
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1250	20% Discount to BIS
12.2 Table 1(Breaking Load Test- After Stranding)	-	1250	20% Discount to BIS
12.3 Table 1(Elongation Test- Before Stranding)	-	1250	20% Discount to BIS
12.3 Table 1(Elongation Test- After Stranding)	-	1250	20% Discount to BIS
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1250	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	1250	20% Discount to BIS
12.3, Table-1(Breaking load before stranding)	-	1250	20% Discount to BIS
12.3, Table-1(Breaking load after stranding)	-	1250	20% Discount to BIS
12.4(Wrapping test)	-	1250	20% Discount to BIS
12.5, Table 1(Resistance test)	-	1250	20% Discount to BIS
12.6, Table 3(Measurement of lay ratio)	-	1250	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

32237 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1875	20% Discount to BIS
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	4375	20% Discount to BIS
16.4(Flammability Test)	-	1250	20% Discount to BIS
16.6(Flame Retardance Test on Single Cables)	-	3750	20% Discount to BIS
16.5(Oxygen Index Test)	-	4375	20% Discount to BIS
16.1(Temperature Index)	-	4375	20% Discount to BIS
16.9(Test for Halogen Acid Gas Evolution)	-	3750	20% Discount to BIS
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	325	20% Discount to BIS
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	625	20% Discount to BIS
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	625	20% Discount to BIS
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	625	20% Discount to BIS
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	625	20% Discount to BIS
13.3(Armouring : Dimensions -Wire Diameter)	-	625	20% Discount to BIS
13.6 a)(ARMOURING: Tensile Strength)	-	625	20% Discount to BIS
13.6 b)(ARMOURING: Elongation )	-	625	20% Discount to BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	625	20% Discount to BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	625	20% Discount to BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1250	20% Discount to BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1250	20% Discount to BIS
13.6 g)(ARMOURING: Resistivity)	-	1250	20% Discount to BIS
9.2(INSULATION : Thickness of Insulation)	-	325	20% Discount to BIS
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	320	20% Discount to BIS
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	325	20% Discount to BIS
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	320	20% Discount to BIS
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	175	20% Discount to BIS
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	150	20% Discount to BIS
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	175	20% Discount to BIS
15.1 d)1)(Physical tests for sheath : Elongation )	-	150	20% Discount to BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	781	20% Discount to BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	781	20% Discount to BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	781	20% Discount to BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	781	20% Discount to BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	781	20% Discount to BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	781	20% Discount to BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	781	20% Discount to BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	781	20% Discount to BIS
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1562	20% Discount to BIS
15.1 d)5)( Loss of mass in air oven- sheath )	-	1562	20% Discount to BIS
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	320	20% Discount to BIS
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	325	20% Discount to BIS
15.1 d)4)(Hot deformation : Insulation )	-	600	20% Discount to BIS
15.1 d)4)(Hot deformation : Sheath )	-	650	20% Discount to BIS
15.1 d)6)(Heat shock test- Insulation )	-	325	20% Discount to BIS
15.1 d)6)(Heat shock test- sheath )	-	320	20% Discount to BIS
15.1 d)7)(Thermal stability- insulation )	-	1250	20% Discount to BIS
15.1 d)7)(Thermal stability- Sheath )	-	1250	20% Discount to BIS
15.1 e)(Insulation resistance test : Volume Resistivity )	-	900	20% Discount to BIS
15.1 e)(Insulation resistance test : IR Constant )	-	975	20% Discount to BIS
15.4 a)(Cold bend test- Insulation ( Optional test))	-	650	20% Discount to BIS
15.4 a)(Cold bend test- Sheath ( Optional test))	-	600	20% Discount to BIS
15.4 b)(Cold impact test- Insulation ( Optional test))	-	650	20% Discount to BIS
15.4 b)(Cold impact test- Sheath ( Optional test))	-	600	20% Discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Up to and including 400 sq. mm.

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

31320 View breakup
Single Core Unsheathed Cable Rs. 28000/- Single Core Sheathed Cable RS. 28000/- Charges For FR Cable Rs.30600/- Charges For FR-LSH Cable Rs.31320/- Extra Charges For Armouring of Cable Rs.7500.00 Separated Wire Before Stranding (If Provided) Rs.900.00 Each Additional Core, Charge Per Core Rs. 2800.00 Optional Test (If Required) Rs. 1500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2(HIGH VOLTAGE TEST )	-	1875	20% discount to BIS
16.3(FLAMMABILITY TEST : Period of Burning )	-	1250	20% discount to BIS
16.3(FLAMMABILITY TEST : Unaffected length )	-	1250	20% discount to BIS
16.9(Oxygen Index Test)	-	4375	20% discount to BIS
16.1(Flame Retardance Test on Single Cables)	-	4375	20% discount to BIS
16.14(Temperature Index)	-	5625	20% discount to BIS
16.13(Test for Halogen Acid Gas Evolution)	-	3750	20% discount to BIS
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1875	20% discount to BIS
15.1 a) i)(Annealing Test ( For copper wire ) )	-	625	20% discount to BIS
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	625	20% discount to BIS
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	625	20% discount to BIS
15.1 a) iii)(Wrapping test (for aluminium))	-	625	20% discount to BIS
15.1 a) iv)(Resistance test - Main conductor)	-	625	20% discount to BIS
15.1 a) iv)(Resistance test - Neutral conductor)	-	625	20% discount to BIS
13.3(Armouring : Dimensions -Wire Diameter)	-	625	20% discount to BIS
13.6 a)(ARMOURING: Tensile Strength)	-	625	20% discount to BIS
13.6 b)(ARMOURING: Elongation )	-	625	20% discount to BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	625	20% discount to BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	625	20% discount to BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1250	20% discount to BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1250	20% discount to BIS
13.6 g)(ARMOURING: Resistivity)	-	1250	20% discount to BIS
9.2(Thickness of Insulation - Average)	-	300	20% discount to BIS
9.3(Thickness of Insulation - Minimum)	-	300	20% discount to BIS
14.3(Thickness of outer sheath - AVERAGE)	-	300	20% discount to BIS
14.3(Thickness of outer sheath - minimum)	-	325	20% discount to BIS
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	300	20% discount to BIS
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	325	20% discount to BIS
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1562	20% discount to BIS
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1562	20% discount to BIS
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1562	20% discount to BIS
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1562	20% discount to BIS
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	3125	20% discount to BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	625	20% discount to BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	625	20% discount to BIS
15.1 e) v) (Sheath : Hot deformation)	-	1250	20% discount to BIS
15.1 e) vi) (Sheath : Heat shock test)	-	625	20% discount to BIS
15.1 e) vii) (Sheath : Thermalstability)	-	2500	20% discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

• Up to and including 400 sq. mm.

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

16125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	625	20%discount to BIS
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	625	20%discount to BIS
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	625	20%discount to BIS
7.2( Thickness of insulation)	-	625	20%discount to BIS
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	650	20%discount to BIS
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	600	20%discount to BIS
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	3125	20%discount to BIS
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	3125	20%discount to BIS
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	2500	20%discount to BIS
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	2500	20%discount to BIS
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1250	20%discount to BIS
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1250	20%discount to BIS
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	5625	20%discount to BIS
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	625	20%discount to BIS
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	625	20%discount to BIS
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1125	20%discount to BIS
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	20%discount to BIS
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1875	20%discount to BIS
10.1 g)(High voltage test - IS10810:Part 45)	-	1875	20%discount to BIS
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	625	20%discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Included w.e.f. 08.11.2018.

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

8500 View breakup
For 7 Strands Rs. 5625.00 For 13 Strands Rs. 5785.00 Separated Wire Before Stranding (If Provided) Rs. 1500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	150	20% discount to BIS
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	150	20% discount to BIS
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	150	20% discount to BIS
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	175	20% discount to BIS
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	310	20% discount to BIS
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	310	20% discount to BIS
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	320	20% discount to BIS
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	310	20% discount to BIS
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	300	20% discount to BIS
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	300	20% discount to BIS
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	300	20% discount to BIS
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	350	20% discount to BIS
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	150	20% discount to BIS
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	150	20% discount to BIS
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	150	20% discount to BIS
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	175	20% discount to BIS
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	500	20% discount to BIS
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	500	20% discount to BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	625	20% discount to BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	625	20% discount to BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	625	20% discount to BIS
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	625	20% discount to BIS
13.7.2 (chem)(Mass of Zinc coating)	-	2125	20% discount to BIS
13.7.2 (chem)(Uniformity of Zinc coating)	-	1500	20% discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

• Up & including 100 Sq.mm

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

13750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	40	20% discount to BIS
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	35	20% discount to BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	50	20% discount to BIS
7.2(Minimum inside diameter of conduit)	-	50	20% discount to BIS
7.3(Length of conduit)	-	50	20% discount to BIS
7.4(Unifomity of The wall Thickness)	-	74	20% discount to BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	177	20% discount to BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1635	20% discount to BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	285	20% discount to BIS
10(Resistance to Heat -Ball presure test)	-	168	20% discount to BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

For sizes 20mm to 50mm.

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

35000 View breakup
Rs.35,000/- for Electronic Video games, Power adapters for audio, video & similar electronic apparatus. Rs.35,000/- for Plasma/ LCD/ LED TV of screen size 32” & above, Plasma/ LCD/LED TVs of screen size up to 32”, Amplifiers with input power 2000W & above, Optical Disc Players with built in amplifier with input 2000W & above. Rs.35000/- Video Camera, Webcam (Finished Products), Smart Speaker (With and without display), Bluetooth Speakers.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Heating under normal operating conditions)	-	6500	20% discount to BIS
5(Marking and instructions)	-	650	20% discount to BIS
8(Constructional requirements with regard to the protection against electric shock)	-	5200	20% discount to BIS
9(Electric shock hazard under normal operating conditions)	-	5850	20% discount to BIS
10(Insulation requirements)	-	7800	20% discount to BIS
11(Fault conditions)	-	7150	20% discount to BIS
12(Mechanical strength)	-	3250	20% discount to BIS
13(CLEARANCES and CREEPAGE DISTANCES)	-	6500	20% discount to BIS
15(TERMINALS)	-	1300	20% discount to BIS
16(External flexible cords)	-	1300	20% discount to BIS
17(Electrical connections and mechanical fixings)	-	3250	20% discount to BIS
19(Stability and mechanical hazards)	-	3250	20% discount to BIS
20(Resistance to fire)	-	6500	20% discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

REVISED VERSON IS 616:2017. EXCLUSIONS: Ionizing radiation test (Cl.6.1), Laser radiation (Cl.6.2), Printed Boards(Cl.13.5), Component test (Cl.14), Mechanical strength of picture tubes & protection against the effect of implosion (Cl.18), Electrical Components (Cl.20.2.2), Internal wiring (Cl.20.2.3), Printed Boards (Cl.20.2.4), Components and parts (Cl.20.2.5), Fire Enclosure (Cl.20.3)

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

35000 View breakup
Laptop/ Notebook/ Tablet, Video monitors of screen size 32” & above, Printer, Plotter, Scanner, Visual display unit, Copying machines/ duplicators, Automatic data processing machine, Point of sale terminals & Cash Registers, Video monitors of screen size up to 32”, Smart Card Readers, Passport Reader, Banks for use in portable applications, Mobile phones, Wireless Keyboard/ Wired Keyboard, Set Top Box, Power adaptor for IT equipments, CCTV Cameras/ CCTV Recorders, Digital Camera. ADDITIONAL PRODUCTS INCLUDED W.E.F. 24-01-2022, mail processing machines / postage machines / franking machines / telephone answering machine= 35000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.6(Power interface .)	-	1300	breakup
1.7(Markings and instructions)	-	650	breakup
2.1(Protection from electric shock and energy hazards)	-	4550	breakup
2.2(SELV circuits)	-	1625	breakup
2.4(Limited current circuits)	-	1105	breakup
2.5(Limited power sources .)	-	975	breakup
2.6(Provisions for earthing and bonding)	-	1040	breakup
2.7(Overcurrent and earth fault protection in primary circuits)	-	650	breakup
2.8(Safety interlocks)	-	1625	breakup
2.9(Electrical insulation)	-	3250	breakup
2.10(Clearances, creepage distances and distances through insulation)	-	8255	breakup
3.1(General)	-	3250	breakup
3.2(Connection to a mains supply)	-	1300	breakup
3.3(Wiring terminals for connection of external conductors)	-	1300	breakup
3.4(Disconnection from the mains supply)	-	650	breakup
3.5(Interconnection of equipment)	-	650	breakup
4.1(Stability)	-	325	breakup
4.2(Mechanical strength)	-	2080	breakup
4.3(Design and construction)	-	650	breakup
4.4(Protection against hazardous moving parts)	-	975	breakup
4.5(Thermal requirements)	-	2990	breakup
4.6(Openings in enclosures)	-	2925	breakup
4.7(Resistance to fire)	-	2925	breakup
5.1(Touch current and protective conductor curren)	-	845	breakup
5.2(Electric strength)	-	1300	breakup
5.3(Abnormal operating and fault conditions)	-	2600	breakup
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	1300	breakup
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	3055	breakup
6.3(Protection of the telecommunication wiring system from overheating)	-	2600	breakup
7.1(General)	-	650	breakup
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	650	breakup
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	2275	breakup
7.4(Insulation between primary circuits and cable distribution systems)	-	2600	breakup

Complete

19 Jul, 2024

06 Jun, 2027

EXCLUSIONS: Component (Cl.1.5), Safety Interlocks: Moving parts (Cl.2.8.5), Switches & Relays (Cl.2.8.7),Semiconductor Devices (Opto-coupler test) (Cl.2.10.5.4), Insulation in wound components (Cl.2.10.5.11), Wire in wound components (Cl. 2.10.5.12), Tests for semiconductor devices & for cemented joints (Cl. 2.10.11), Cathode Ray Tube (Cl.4.2.8), Batteries (cl.4.3.8); Radiation (Cl.4.3.13), Electromechanical components (Cl. 5.3.5), Insulating winding wires (Annex U), Evaluation of IC current limiters (Annex CC).

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

18750 View breakup
Single Core Unsheathed Cable Rs. 7500.00 Single Core Sheathed Cable RS. 10300.00 Extra Charges For Outdoor Use Cable Rs.5625.00 Extra Charges For Low Temperature Use Cable Rs.2250.00 Charges For FR Cable Rs. 15000.00 Charges For FR-LSH Cable Rs.18750.00 Separated Wire Before Stranding (If Provided) Rs.900.00 Each Additional Core, Charge Per Core Rs. 2800.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3125	20%discount to BIS
10.4(Flammability test- Unaffected portion)	-	625	20%discount to BIS
10.4(Flammability test-Burning after flame removal)	-	625	20%discount to BIS
10.1(HV (water immersion))	-	1875	For AC TEST 20%discount to BIS
10.1(HV (water immersion))	-	4375	FOR DC TEST 20%discount to BIS
10.5(Oxygen index)	-	4375	20%discount to BIS
10.7(Temperature index)	-	4375	20%discount to BIS
10.6(Halogen evolution)	-	3750	20%discount to BIS
10.2(HV (room temperature))	-	1875	20%discount to BIS
4.1(Annealing test (for copper))	-	625	20%discount to BIS
4.1(Tensile test (for Al)- After Stranding)	-	625	20%discount to BIS
4.1(Tensile test (for Al)-Before Stranding)	-	625	20%discount to BIS
4.1(Wrapping test (for Al))	-	625	20%discount to BIS
4.2(Conductor resistance test)	-	625	20%discount to BIS
10.11(Per sulphate test (for tinned Cu cable only))	-	1250	20%discount to BIS
9(Overall dimensions)	-	625	20%discount to BIS
5.3(Thickness of Insulation)	-	625	20%discount to BIS
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	625	20%discount to BIS
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1875	20%discount to BIS
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1875	20%discount to BIS
Table 1 iii) d) 9)(Cold impact for sheath)	-	1250	20%discount to BIS
Table 1 iii) c) 9)(Cold impact for insulation)	-	625	20%discount to BIS
Table 1 iii) d) 5)(Heat shock-Sheath )	-	625	20%discount to BIS
Table 1 iii) c) 5)(Heat shock-Insulation )	-	625	20%discount to BIS
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	2500	20%discount to BIS
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	2500	20%discount to BIS
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	625	20%discount to BIS
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	625	20%discount to BIS
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	3125	20%discount to BIS
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	3125	20%discount to BIS
Table 1 iii) d) 8)(Cold bend for sheath)	-	1250	20%discount to BIS
Table 1 iii) c) 8)(Cold bend for insulation)	-	625	20%discount to BIS
Table 1 iii) c) 1)(Elongation (Without ageing))	-	625	20%discount to BIS
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	625	20%discount to BIS

Complete

19 Jul, 2024

06 Jun, 2027

Following Additional • Up to and including 400 sq. mm.

Bureau of Indian Standards

The National Standards Body of India

KC INDIA TEST LABORATORIES LLP

A-16/2, Site-IV, Sahibabad Industrial Area, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

9599880265 kcitestlab@gmail.com

Scope List