BIS - LIMS (Laboratory Information Management System)

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

G SECTOR, GOVINDPURA INDUSTRIAL AREA, J. K. ROAD, BHOPAL, BHOPAL, Bhopal, Madhya Pradesh, 462023

7869955244 cipet.bhopal@gmail.com

Scope List

Reset

111 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 6312 (1994)

Polyethylene containers for the transport of materials - Specification (Second Revision)

13150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	2000	-
6(BRIMFUL CAPACITY)	-	500	-
7(Workmanship and Finish)	-	1000	-
8.1 - Table 1 - (i)(Stacking test)	-	1100	-
8.1 - Table 1 - (ii)(Clousre leakage test)	-	850	-
8.1 - Table 1 - (iii)(Drop test)	-	3300	-
8.1 - Table 1 - (iv)(Pressure tightness test)	-	1500	-
8.1 - Table 1 - (v)(Hydrostatic test)	-	1000	-
8.1 - Table 1 - (vi)(Handle strength test)	-	1100	-
8.1 - Table 1 - (vii)(Top load resistance test)	-	1100	-
8.1 - Table 1 - (viii)(Environmental stress crack resistant test)	-	2000	-
10(Marking)	-	0	-

Complete

31 Dec, 2026

IS 15225 (2002)

Chlorinated polyvinyl chloride compounds used for pipes and fittings - Specifications

18100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1(Resin k-value)	-	1100	-
8.1.2(Resin chlorine content)	-	4300	-
8.1.3(Form)	-	250	-
8.1.4(Compound chlorine content)	-	4300	-
8.1.5(Appearance)	-	300	-
8.2.1(Vicat softening temperature)	-	1725	-
8.2.2(Charpy impact strength)	-	1725	-
8.2.3(Tensile strength)	-	1725	-
8.2.4(Tensile modulus)	-	1725	-
8.3(Ash content)	-	950	-
4(Designation)	-	0	-

Complete

31 Dec, 2026

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

52625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1125	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	-
5.3(Ash content- Any Method)	-	950	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	925	-
5.3(Density of Higher olefin - IS 7328:2020)	-	500	-
5.3(Toluene extract - Any Method)	-	900	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	700	-
5.3(Carbon black particle size - Any Method)	-	3000	-
6.2(Colour- IS 14333-2022)	-	250	-
7.1(Visual Appearance- IS 14333-2022)	-	300	-
7.2(Length- IS 14333-2022)	-	250	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	900	-
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	-
8.6(Density-IS 7328:2020)	-	500	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1600	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1600	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	-
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	0	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	0	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	0	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	0	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Density of Higher olefin - IS 7328:2020)	-	0	-
5.3(Toluene extract - Any Method)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	-
6.2(Colour- IS 14333-2022)	-	0	-
7.1(Visual Appearance- IS 14333-2022)	-	0	-
7.2(Length- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	-
8.3(Carbon black content- IS 2530-1963)	-	0	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	-
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	0	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	0	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	0	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	0	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Density of Higher olefin - IS 7328:2020)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
6.2(Colour- IS 14333-2022)	-	0	-
7.1(Visual Appearance- IS 14333-2022)	-	0	-
7.2(Length- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	-
8.3(Carbon black content- IS 2530-1963)	-	0	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	-

Complete

31 Dec, 2026

Included w.e.f. 28-06-2023.

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

496750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	500	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	-
5.1, 5.7 Table 2(iv) Volatile content)	-	700	-
5.1, 5.7 Table 2(v) Water content1))	-	700	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	700	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.6(ii) Hydraulic characteristics)	-	11250	-
5.6(iii) Thermal stability (Oxidation induction time))	-	2200	-
8.5(Pigment Dispersion)	-	700	-
8.7(Volatile Matter Content)	-	700	-
8.3(Density)	-	500	-
8.2(Reversion Test)	-	700	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4250	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5050	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11000	-
6(Dimensions of pipes)	-	0	-
6.1(Outside Diameter)	-	0	-
6.1(Out of Roundness (Ovality))	-	800	-
6.2(Wall Thickness)	-	550	-
7(Finish)	-	300	-
5.7(PE Compound Quality Evaluation)	-	400000	-
8.9(Resistance to Weathering)	-	9000	-
5.6(Resistance to Weathering)	-	9000	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	-
5.4(U-V stabilizer)	-	2000	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	-
8.11(Squeeze-of)	-	6350	-
8.10(Slow Crack Growth Rate Test)	-	5050	8.10.1 Acceptance Test 80 degree centigrade for 165 hrs.
8.10(Slow Crack Growth Rate Test)	-	5750	8.10.2 Type Test 80 degree centigrade for 500 hrs.
5.1(Polyethylene compound)	-	5000	-
4.4(Colour)	-	300	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.3(Density)	-	0	-
8.2(Reversion Test)	-	700	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
6(Dimensions of pipes)	-	0	-
6.1(Outside Diameter)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall Thickness)	-	0	-
7(Finish)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
8.9(Resistance to Weathering)	-	0	-
5.6(Resistance to Weathering)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.4(U-V stabilizer)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.11(Squeeze-of)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
5.1(Polyethylene compound)	-	0	-
4.4(Colour)	-	0	-
6.4(Length of Pipe)	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.3(Density)	-	0	-
8.2(Reversion Test)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
6(Dimensions of pipes)	-	0	-
6.1(Outside Diameter)	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall Thickness)	-	0	-
7(Finish)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
8.9(Resistance to Weathering)	-	0	-
5.6(Resistance to Weathering)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.11(Squeeze-of)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
5.1(Polyethylene compound)	-	0	-
4.4(Colour)	-	0	-
6.4(Length of Pipe)	-	0	-

Complete

31 Dec, 2026

Included w.e.f. 28-06-2023. Exclusion: Cl.5.4 (U-V stabilizer)

IS 5175 (2022)

Fibre ropes - Polypropylene split film monofilament and multifilament PP 2 and polypropylene high tenacity multifilament PP 3 3- 4- 8- and 12- strand ropes (fourth revision)

7250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6, (Table 1,2,3)(Diameter)	-	250	-
Clause 6, (Table 1,2,3)(Linear Density)	-	500	-
Clause 6, (Table 1,2,3)(Minimum Breaking Force)	-	1100	-
5.2(Pitch or length of lay)	-	500	-
5.1(type A: 3-strand hawser-laid rope)	-	2000	-
5.1(type B: 4-strand shroud-laid rope)	-	0	-
5.1(type L: 8-strand braided rope)	-	0	-
5.1(type T: 12-strand braided rope)	-	0	-
Clause 6, (Table 1,2,3)(Diameter)	-	0	-
Clause 6, (Table 1,2,3)(Linear Density)	-	0	-
Clause 6, (Table 1,2,3)(Minimum Breaking Force)	-	0	-
5.2(Pitch or length of lay)	-	0	-
5.1(type A: 3-strand hawser-laid rope)	-	0	-
5.1(type B: 4-strand shroud-laid rope)	-	0	-
5.1(type L: 8-strand braided rope)	-	0	-
5.1(type T: 12-strand braided rope)	-	0	-
Clause 6, (Table 1,2,3)(Diameter)	-	0	-
Clause 6, (Table 1,2,3)(Linear Density)	-	0	-
Clause 6, (Table 1,2,3)(Minimum Breaking Force)	-	0	-
5.2(Pitch or length of lay)	-	0	-
5.1(type A: 3-strand hawser-laid rope)	-	0	-
5.1(type B: 4-strand shroud-laid rope)	-	0	-
5.1(type L: 8-strand braided rope)	-	0	-
5.1(type T: 12-strand braided rope)	-	0	-

Complete

31 Dec, 2026

Included w.e.f. 28-06-2023.

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

35980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2("Fabric b) Linear Density")	-	500	-
4.1(Raw Meterial)	-	2000	-
4.2("Fabric a) Width of Tape")	-	500	Width+ Mesh of Fabric
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	300	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	300	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	300	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	1100	-
Cl. No.5.4(Breaking Strength of Fabric)	-	1100	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	1100	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	1100	-
4.5(Mass of The Lamination)	-	300	-
4.4.1(Thickness of Linear)	-	250	-
4.4.3(Bottom Seam of Loose Liner)	-	250	-
4.7(Mouth of the Sack)	-	250	-
Cl. No.5.7(UV Resistance)	-	12380	UV Exposure + Breaking strength in LW & WW
Cl. No.5.6(Drop Impact testing of filled sack)	-	1100	-
4.3(Sacks)	-	300	-
4.4.2(Visual Observation)	-	250	-
4.6.1(Distance between the Two Row of Stitches)	-	250	Dimension
4.6.1(Distance of outer stitch from the edge of the bag)	-	250	-
4.6.1(Depth of the Stitch( Double fold))	-	250	-
4.6.1(No.of Stitches/dm)	-	300	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	1100	-
4.6.2(Breaking Load for UV Stabilized sack)	-	4000	UV Presence + Identification of Material
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	950	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.2(Visual Observation)	-	250	-
Cl. No.5.3(Mass of Bale)	-	0	GSM
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.2("Fabric b) Linear Density")	-	0	-
4.1(Raw Meterial)	-	4000	Migration+ Identification
4.2("Fabric a) Width of Tape")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.7(Mouth of the Sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
4.3(Sacks)	-	0	-
4.4.2(Visual Observation)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.5.3(Mass of Bale)	-	0	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.2("Fabric b) Linear Density")	-	500	-
4.1(Raw Meterial)	-	0	-
4.2("Fabric a) Width of Tape")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.7(Mouth of the Sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
4.3(Sacks)	-	0	-
4.4.2(Visual Observation)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-
4.2("Fabric b) Linear Density")	-	0	-
4.1(Raw Meterial)	-	0	-
4.2("Fabric a) Width of Tape")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	0	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.7(Mouth of the Sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	0	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
4.3(Sacks)	-	0	-
4.4.2(Visual Observation)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-

Complete

31 Dec, 2026

Included w.e.f. 28-06-2023.

IS 10151 (2019)

Polyvinyl chloride (Pvc) and its copolymers for its safe use in contact with foodstuffs, pharmaceuticals and drinking water - Specification (First Revision)

4150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5(Overall Migration, IS 9845)	-	2325	Cl. 3.4
4.3(Pigments and Colourants, IS 9833)	-	0	-
5.2(Marking)	-	0	-
4.4(Monomer content)	-	3000	Cl. no. 3.3.1

Complete

31 Dec, 2026

IS 14597 (1998)

Synthetic tarpaulins(Heavy Duty Protective Covers) made from coated nylon or polyester fabrics specification

50775 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CL. 5.1( Workmanship)	-	250	-
CL. 5.2(Accelerated ageing)	-	4200	5.2 Ageing at 70 degree centigrade for 168 hrs.
CL. 5.5(Resistance to cold)	-	1100	-
CL. 5.6(Shear strength of joint )	-	1100	-
(Cl 5 & Table 1)(Requirements )	-	1500	5.4 Flex test before ageing 50000 cycles
(Cl 5 & Table 1)(Requirements )	-	1500	5.4 Flex test after ageing 50000 cycles
(Cl 5 & Table 1)(Requirements )	-	1100	5.7 Ease of in-sito repair
(Cl 5 & Table 1)(Requirements )	-	250	5.8 Cover confirmation as per table -1
Cl 5 & Table 1(Total mass per unit area)	-	250	-
Cl 5 & Table 1(Breaking strength: Longitudinal Direction)	-	2700	Breaking Strength Before Ageing
(Cl 5 & Table 1)(Requirements )	-	2200	Breaking Strength After Ageing
(Cl 5 & Table 1)(Requirements )	-	1350	Blocking
(Cl 4.5)(Coating)	-	0	-
(Cl 4.5)(Coating)	-	1300	4.5.3 Coating exposure (100 degree centigrade for 48 hrs.)
(Cl 5 & Table 1)(Requirements )	-	21200	5.9 Color fastness to rubbing (Wet & dry), Color fastness by xenon arc
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	300	6.0 Construction of Heavy duty cover
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	2000	6.1.1 Identification
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	250	6.1.2 Eyelet (Dimension)
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	500	6.1.3/6.1.4 Hemmed by heat sealing, Lap joint, Panel Length
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	250	6.2 Fixing of eyelet
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	250	6.2.1 No of length of lashing rope
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	250	6.2.2 Area of cover
(Cl 4.5)(Coating)	-	2950	4.1 Identification, Filler Content
(Cl 4.5)(Coating)	-	250	Nos. of cuts
(Cl 4.5)(Coating)	-	250	Usable Width
(Cl 4.5)(Coating)	-	2250	PVC coating (Presence of UV stabilizer) + Pigment (Visual)
(Cl 4.5)(Coating)	-	750	Odour, Visual, Surface finish
(Cl 5 & Table 1)(Requirements )	-	850	Flame Resistance Test
(Cl 5 & Table 1)(Requirements )	-	1200	Fusion (By Acetone Chemical)
CL. 5.1( Workmanship)	-	-	-
CL. 5.2(Accelerated ageing)	-	-	-
CL. 5.5(Resistance to cold)	-	-	-
CL. 5.6(Shear strength of joint )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
Cl 5 & Table 1(Total mass per unit area)	-	-	-
Cl 5 & Table 1(Breaking strength: Longitudinal Direction)	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
Cl 6, (Cl. 6.2)(Construction: Fixing of Eyelets)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 4.5)(Coating)	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-
(Cl 5 & Table 1)(Requirements )	-	-	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 11197 (1985)

Specification for monoaxially oriented polypropylene tapes

5650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

31 Dec, 2026

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

32825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1300	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
9.1(PIPE ENDS)	-	0	-
8(SEALING RINGS)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.2.1(DIMENSIONS-Socket)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
7(DIMENSIONS-PIPE-Nominal Diameter)	-	0	The test charges has already been taken in cl. no. 7.2.1.2-Table 4
Clause 10.7(Sulphated Ash Content)	-	950	-
10.1(Colour)	-	0	-
D-2.1.2.4(Effect on Water Test)	-	3000	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-	0	-
10.1(Surface Finish)	-	0	-
6.1.2(PVC Resin)	-	4100	VCM Content + K-Value

Complete

31 Dec, 2026

IS 14635 : Part 1 (2020)

Fluoropolymer Dispersions and Moulding and Extrusion Materials Part 1 Designation System ( First Revision )

7300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5.1.1.1(Standard Specific Gravity in accordance with IS 14635 part 2)	-	500.00	-
4.5.1.1.3(Bulk Density)	-	500.00	-
4.5.1.1.5(Tensile Properties (Tensile stress) in accordance with IS 13360 (Part 5/Sec 2))	-	1350.00	1100.00 (Testing Charge) + 250.00 (Conditioning charge)
4.5.1.1.5(Tensile Properties (Elongation) in accordance with IS 13360 (Part 5/Sec 2))	-	1350.00	1100.00 (Testing Charge) + 250.00 (Conditioning charge)
4.5.1.1.6(Dielectric strength (IEC 60243-1 or ASTM D 149))	-	1350.00	1100.00 (Testing Charge) + 250.00 (Conditioning charge)
4.5.1.1.9(Melting Peak Temperature in accordance with IS 14635 (Part 2)	-	2250.00	2200.00 (Testing Charge) + 250.00 (Conditioning charge)

Complete

31 Dec, 2026

IS 16627 (2017)

Agro textiles “ High density polyethylene (HDPE) laminated woven lay flat tube for use in mains and submains of drip irrigation system “ Specification

115531 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.9(Pressure Impulse Test, )	-	0	-
6.8(Welded Seam Strength after UV Exposure Annexure B, 500 Hours)	-	1100	-
6.6(Kink Test 0.5 Kgf/cm2)	-	1100	-
5 /5.1(MANUFACTURE / Lamination)	-	4500	-
6.5(Length)	-	250	-
4 (a)(TYPES / type-1)	-	0	-
4 (b)(TYPES / type-2)	-	0	-
3/ 3.1 (MATERIALS / HDPE Tapes)	-	3250	-
3.2(HDPE FABRIC)	-	500	-
5 /5.2(MANUFACTURE / Lamination)	-	250	-
5 /5.3, table -1(MANUFACTURE / Lamination)	-	250	-
6.1(Internal Diameter)	-	250	-
6.2(Workmanship)	-	300	-
6.3, table -I , table, -ii(Hydrostatic Burst Pressure Test)	-	1500	-
6.4 , Table-3 for col-3 or col-4(Proof Pressure Test)	-	1500	-
6.7(Welded Seam Strength before UV Exposure)	-	1350	-
6.1(Colour)	-	250	-
7.0(FITTINGS)	-	250	-
8.0(PATCHING OF THE LAY FLAT TUBE FOR DRIP IRRIGATION)	-	250	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 6590 (1972)

Specification for braided nylon rope for mountaineering purposes

8450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1,(Diameter of Rope,Annex 4)	-	550	Lenth of coil
3.1/3.1.1(Manufacture of Yarn)	-	2000	3.1.1 Material Identification
4.1, Table 1(No of ends per Spindle)	-	300	-
3.1/3.1.1, Refer table 1(Approximate count of the yarn in the core and sheath together)	-	300	-
4.1, Table 1(Univershal count(or Denier ) of yarn(Approx)- Core)	-	250	-
4.1, Table 1(Univershal count(or Denier ) of yarn(Approx)- Sheath)	-	500	-
4.1, Table 1(Linear density -Refer Annex 3)	-	500	-
4.1, Table 1(Breaking load on 45 cm Test length-Refer Annex 5)	-	1350	-
4.1, Table 1(Elongation at 20% load -Refer Annex 5)	-	2450	-
4.1, Table 1(Angle of sag -refer annex 7 )	-	600	-
4.2(Slackness of Sheath-Refer Annex 8)	-	1100	-
3.1.2(Manufacture of Yarn)	-	950	Filler Content

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

50450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4( Line/ Cord beading IS 7903)	-	250	Nil
4.0(Types IS 7903)	-	250	Nil
5.1.1(Lamination IS 7903)	-	1050	Nil
5.1.2(Lamination IS 7903)	-	1050	Nil
5.2.1(Construction IS 7903)	-	250	Nil
5.2.1(Construction IS 7903)	-	250	Nil
5.2.1(Construction IS 7903)	-	0	Charges already taken in clause no. 5.2.1
5.2.1(Construction IS 7903)	-	0	Charges already taken in clause no. 5.2.1
5.2.1(Construction IS 7903)	-	0	Charges already taken in clause no. 5.2.1
5.2.1(Construction IS 7903)	-	0	Charges already taken in clause no. 5.2.1
5.2.1(Construction IS 7903)	-	0	Charges already taken in clause no. 5.2.1
5.3(Joint/Seam, IS 7903)	-	250	Nil
5.4(Fixing of Eyelets, IS 7903)	-	250	Nil
5.4(Fixing of Eyelets ,IS 7903)	-	0	Charges already taken in clause no. 5.4
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	250	Nil
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0	Charges already taken in clause no. 6.1
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	0	Charges already taken in clause no. 6.1
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	500	Nil
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	0	Charges already taken in clause no. 6.1
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	1100	Nil
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	0	Charges already taken in clause no. 6.1
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	1100	Nil
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0	Charges already taken in clause no. 6.1
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	1100	Nil
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	29950	Test charge Rs. 2200/- plus UV exposure charges Rs. 27750/-
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1100	Nil
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	1100	Nil
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100	Nil
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100	Nil
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100	Nil
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	850	Nil
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950	Nil
6.2(Length, IS 7903)	-	250	Nil
6.2(Width, IS 7903)	-	250	Nil
6.2(height, IS 7903)	-	0	Charges already taken in clause no. 6.2
6.3(Water Proofness,IS 7941)	-	1000	Nil
6.3(Water Proofness, IS 7940)	-	5200	Test charge Rs. 1000/- plus ageing charges Rs. 4200/-
6.2(dimension(l))	-	0	Charges already taken in clause no. 6.2
6.2(dimension(w))	-	0	Charges already taken in clause no. 6.2
6.2(dimension(h))	-	0	Charges already taken in clause no. 6.2

Complete

31 Dec, 2026

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

18548 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MANUFACTURE-Raw Material- IS 10146 or IS 10910)	-	1050	Material Identification
3.1(MANUFACTURE-Raw Material)	-	750	Fabric (tape width), Linear Density
3.2(MANUFACTURE-)	-	300	Sacks (Visual Appearance)
3.3(Sacks)	-	300	Visual Appearance (Liner)
3.3.1(Sacks-Table 1)	-	0	Visual Appearance (Liner)
3.4(Liner)	-	0	Identification
3.4.1(Liner)	-	0	GSM & Overlap dimension
3.4.2(Lamination)	-	1800	Identification, GSM, Overlap dimension
3.5(Bottom Seam-(see IS 10789).)	-	1300	Seam (Dimension), Identification (Stitching Material)
3.6.1(Bottom Seam-)	-	0	Opacity
3.7(Mouth of the Sack)	-	250	Capacity
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	0	Capacity
4.2(UV Resistance)	-	0	UV Resistance(144 hrs)* (100x60+44x40)
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	2700	Avg. Breaking Strength & Elongation at break of Fabric after UV radiation & weathering, Length wise, Widthwise
4.3(Mass-(Annexure E))	-	250	Mass
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 70 μm ± 10 percent in case of LDPE/LLDPE)	-	0	-
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	0	-
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	-
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	0	-
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	0	-
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
3.1(MANUFACTURE-Raw Material- IS 10146 or IS 10910)	-	0	-
3.1(MANUFACTURE-Raw Material)	-	0	-
3.2(MANUFACTURE-)	-	0	-
3.3(Sacks)	-	0	-
3.3.1(Sacks-Table 1)	-	0	-
3.4(Liner)	-	0	-
3.4.1(Liner)	-	0	-
3.4.2(Lamination)	-	0	-
3.5(Bottom Seam-(see IS 10789).)	-	0	-
3.6.1(Bottom Seam-)	-	0	-
3.7(Mouth of the Sack)	-	0	-
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	0	-
4.2(UV Resistance)	-	0	-
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	0	-
4.3(Mass-(Annexure E))	-	0	-
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 70 μm ± 10 percent in case of LDPE/LLDPE)	-	0	-
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	0	-
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	-
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	0	-
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	0	-
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.1 , Table 1(REQUIREMENTS)	-	0	Dimensions (Inside length & width)-250 Ends per dm-250 Picks per dm-250 Mass of Sack (GSM)-500 Avg. Breaking Strength & Elongation at break of Fabric: Lengthwise-1350 widthwise-1100 Min. Breaking Strength of Bottom Seam-1350
3.1(MANUFACTURE-Raw Material- IS 10146 or IS 10910)	-	0	-
3.1(MANUFACTURE-Raw Material)	-	0	-
3.2(MANUFACTURE-)	-	0	-
3.3(Sacks)	-	0	-
3.3.1(Sacks-Table 1)	-	0	-
3.4(Liner)	-	0	-
3.4.1(Liner)	-	0	-
3.4.2(Lamination)	-	0	-
3.5(Bottom Seam-(see IS 10789).)	-	0	-
3.6.1(Bottom Seam-)	-	0	-
3.7(Mouth of the Sack)	-	0	-
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	0	-
4.2(UV Resistance)	-	8260	UV Resistance(144 hrs)* (100x60+44x40),
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	2200	Avg. Breaking Strength & Elongation at break of Fabric after UV radiation & weathering, Length wise, Widthwise
4.3(Mass-(Annexure E))	-	250	Mass
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	0	-
3.4(Liner-The thickness(A-2 of IS 2508) shall be 70 μm ± 10 percent in case of LDPE/LLDPE)	-	0	-
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	0	-
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	-
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	0	-
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	0	-
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.1 , Table 1(REQUIREMENTS)	-	4800	Dimensions (Inside length & width)-500 Ends per dm-250 Picks per dm-250 Mass of Sack (GSM)-500 Avg. Breaking Strength & Elongation at break of Fabric; Lengthwise-1350; widthwise-1100 Min. Breaking Strength of Bottom Seam-1350

Complete

31 Dec, 2026

IS 10146 (1982)

Specification for polyethylene for its safe use in contact with foodstuffs, pharmaceuticals and drinking water zy

2688 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Basic Resin -)	-	1050	-
3.2(Material )	-	0	-
3.3(Pigments and Colourants )	-	0	-
3.4(Overall Migration)	-	2325	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 11066 (2014)

Fibre ropes ¬– Polyester 3-, 4-, 8- and 12- strand ropes (second revision)

7250.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Designation)	-	2000.00	-
5(General requirements)	-	2000.00	-
5.1 Fig. 1 / Fig. 2 / Fig. 3 / Fig. 4(Polyester ropes shall be made in one of the following constructions:)	-	0	-
5.2 Cl.4 of IS/ISO 9554(Construction &manufacture)	-	600.00	-
5.2 Cl.5 of IS/ISO 9555(Lay)	-	250.00	-
5.2 Cl.7 of IS/ISO 9556(Labelling and Marking)	-	250.00	-
5.2 Cl.8 of IS/ISO 9557(Packaging, invoicing and delivery lengths)	-	0	Test charge is already included in 5.2 cl.7
6 Table 1 / Table 2 / Table 3(Linear density)	-	500.00	-
6 Table 1 / Table 2 / Table 3(Minimum breaking force a) Unspliced ropes)	-	1100.00	-
6 Table 1 / Table 2 / Table 4(Minimum breaking force b) Ropes with eye-spliced terminations)	-	0	Test charge is already included in clause number 6. Minimum breaking force a) Unspliced ropes
6 Table 1 / Table 2 / Table 3(Minimum breaking force a) Unspliced ropes)	-	0	Test charge is already included in clause number 6. Minimum breaking force a) Unspliced ropes
6 Table 1 / Table 2 / Table 4(Minimum breaking force b) Ropes with eye-spliced terminations)	-	0	Test charge is already included in clause number 6. Minimum breaking force a) Unspliced ropes
6 Table 1 / Table 2 / Table 3(Minimum breaking force a) Unspliced ropes)	-	0	Test charge is already included in clause number 6. Minimum breaking force a) Unspliced ropes

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 14399 : Part 1 and 2 (1996)

Hot Press Moulded Thermosetting Glass Fibre Reinforced Polyester Resin (GRP) Sectional Water Storage Tanks : Part 1 palels, Part 2 Guidelines for assembly, installation and test

10825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Flange of Panels)	-	250	-
6.1.1(Flange of Panels)	-	0	-
6.2(Flange of Panels)	-	0	-
6.3(Flange of Panels)	-	0	-
6.4(Type/Thickness of panel)	-	250	-
7.0(Visual inspection of the panels)	-	300	-
8, Table-1, Annex-B(Tensile Strength)	-	1600	-
8, Table-1, Annex-C(Bending strength)	-	1600	-
8, Table-1, Annex-D(Elastic moduius in Bend)	-	1600	-
8, Table-1, Annex-E(Glass Content)	-	950	-
8, Table-1, Annex-F(Barcoal Hardness)	-	375	-
8, Table-1, Annex-G(Water Absorption)	-	1100	-
9, Annex-H(Hydrostatic Test)	-	850	-
10.0(Deflection Test)	-	1100	-
Clause 11.3 annex J(As)	-	0	-
Clause 11.3 annex J(Cd )	-	0	-
Clause 11.3 annex J(Cr)	-	0	-
Clause 11.3 annex J(Pb)	-	0	-
Clause 11.3 annex J(Se)	-	0	-
5.0(DimensionSof Tank)	-	0	-
6.2(Assembly)	-	0	-
7.0(Leakage Test)	-	850	-

Complete

31 Dec, 2026

IS 14483 : Part 1 (1997)

Fertilizer and chemical injecfion system: Part 1 venturi injector

6375 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONSTRUCTIONAL REQUIREMENTS)	-	500	-
4.2(CONSTRUCTIONAL REQUIREMENTS)	-	0	-
4.3(CONSTRUCTIONAL REQUIREMENTS)	-	0	-
4.4(CONSTRUCTIONAL REQUIREMENTS)	-	0	-
3.1(Material - The Venturi Injector parts that are in contact with water shall be of non toxic materials and shall be resistant to or protected against degradation caused by operating conditions and types of water, chemicals or other additive solutions used in agricultural irrigation or used for cleaning the system)	-	0	-
4.5(CONSTRUCTIONAL REQUIREMENTS)	-	0	-
4.6(CONSTRUCTIONAL REQUIREMENTS)	-	0	-
5.1(Resistance of Venturi Injector to Internal Hydrostatic Pressure)	-	1000	-
5.2(Performance Test)	-	7000	5.2.1 (i) Motive flow & suction rate of test liquid = 3500/- 5.2.1 (ii) Minimum pressure drop = 3500/-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 14611 (2016)

Multilayered cross laminated sheets/tarpaulins/covers/agricultural films - Specification (First Revision)

39005 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1(Workmanship)	-	250	-
Cl. 6.3(Accelerated ageing test)	-	4200	-
Cl. 6.4(water proofness test)	-	1000	-
Cl. 6.5(Strenght of joints/seams)	-	1100	-
Cl. 6.6(Flex test)	-	7200	Included Flex Test (After Ageing)50000 Cycles* - 1500.00/-
Cl. 7.1(Eyelets and rope lashing)	-	500	Included Ease of in-sito Repair 250/-
Cl 5(Construction)	-	1675	Included Carbon black content - 925/-, Panel - 250/-, Ends & sides dimension - 250/-, Panel Length & Width - 250/-
Table1 - v)(Dart Impact Strength)	-	850	-
Table1 - vi)(Average Tensile Strength & Elongation at Break after Exposing to UV Radiation & Weathering)	-	2200	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- LN light)	-	2200	Longitudinal Direction , Transverse Direction
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- MN Medium)	-	2200	Longitudinal Direction , Transverse Direction
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- HN Heavy)	-	2200	Longitudinal Direction , Transverse Direction
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- LN light)	-	1100	Longitudinal Direction , Transverse Direction
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- MN Medium)	-	1100	Longitudinal Direction , Transverse Direction
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- HN Heavy)	-	10180	UV Exposure

Complete

31 Dec, 2026

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

17880 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	-
4.3(Sacks)	-	300	-
4.3.1(Bottom Seam)	-	300	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Mass of the loose liner )	-	0	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	0	Testing charge is already taken in 5.2 clause of Dimension of Inside width.
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	300	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	-
5.2 and Table 1 x(Ash content )	-	950	-

Complete

31 Dec, 2026

IS 15354 : Part 1 (2018)

Single - Use medical examination gloves: Part 1 specification for gloves made from rubber latex or rubber solution (First Revision)

8950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 & Table 2(Width corresponding to size code (dimension w,Figure 1))	-	500	-
6.2(Watertightness)	-	1000	-
6.3.2 & Table 3(Minimum force at break before accelerated ageing)	-	4200	-
6.3.3 & Table 3(Minimum force at break after accelerated ageing)	-	1350	-
6.3.2 & Table 3(Minimum Elongation at break before accelerated ageing)	-	0	-
6.3.3 & Table 3(Minimum Elongation at break after accelerated ageing)	-	1100	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

157725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(Classification of pipes)	-	300	-
6.2.1 Annex B(Chloride Content of Resin)	-	4300	-
6.3(Compound Properties)	-	4300	-
6.3.1 Annex B(Chloride content)	-	0	CHARGES IS ALREADY HAS TAKEN IN CLAUSE NO. 6.2.1.
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11000	RUPEES 11,000/- FOR TESTING CHARGES AND RUPEES 300/- FOR SPECIMEN/CONDITIONING CHARGES*
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	500	-
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	-
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
7.1.3 (Effective length)	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
8(Pipe Ends)	-	300	-
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8
9.2 IS 12235 (Part 3)(Opacity)	-	575	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. Cl. 9.3,IS 4985 Cl. 10.3
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700	-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100	-
9.6 IS 12235(Part 14)(Density)	-	500	-
10(Mechanical Properties)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	16650	-
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110500	RUPEES 1,000/- FOR TESTING CHARGES AND RUPEES 1,09,500/- FOR SPECIMEN/CONDITIONING CHARGES*
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1400	RUPEES 1,100/- FOR TESTING CHARGES AND RUPEES 300/- FOR SPECIMEN/CONDITIONING CHARGES*
10.4 IS 12235(Part 19)(Flattening Test)	-	500	-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1600	RUPEES 1,100/- FOR TESTING CHARGES AND RUPEES 500/- FOR SPECIMEN/CONDITIONING CHARGES*
7.1.2(Wall Thickness (Maximum))	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
7.1.1(Outside Diameter at any point (Maximum))	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
5 Table 1(Classification of pipes)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE - 5 Table 1 (Classification of pipes).
6.2.1 Annex B(Chloride Content of Resin)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE - 6.2.1 ANNEX B (CHLORIDE CONTENT OF RESIN)
6.3(Compound Properties)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE - 6.3 (COMPOUND PROPERTIES)
6.3.1 Annex B(Chloride content)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE - 6.3.1 ANNEX - B
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 6.3.2.
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 7.1 7.1 IS 12235 (Part 1) Table 2
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 7.1.7.1.1 IS 12235.
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 7.1.2 IS 12235 (Part 1).
7.1.3 (Effective length)	-	0	CHARGES ALREADY HAS TAKEN IN 7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes)
8.0(Pipe Ends)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. - 8.0
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8
9.2 IS 12235 (Part 3)(Opacity)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 9.2
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	CHARGES HAS ALREADY TAKEN.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	CHARGES HAS ALREADY TAKEN.
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0	CHARGES HAS ALREADY TAKEN.
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	0	CHARGES HAS ALREADY TAKEN.
9.6 IS 12235(Part 14)(Density)	-	0	CHARGES HAS ALREADY TAKEN.
10.0(Mechanical Properties)	-	0	CHARGES HAS ALREADY TAKEN.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	CHARGES HAS ALREADY TAKEN.
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	0	CHARGES HAS ALREADY TAKEN.
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	0	CHARGES HAS ALREADY TAKEN.
10.4 IS 12235(Part 19)(Flattening Test)	-	0	CHARGES HAS ALREADY TAKEN.
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	0	CHARGES HAS ALREADY TAKEN.
15.4 (b)(Cold impact)	-	0	CHARGES HAS ALREADY TAKEN.

Complete

31 Dec, 2026

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

61950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	1100	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	1100	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	2300	-
9 (Table 12)(Performance Requirements)	-	1150	-
11.1(Marking General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
5.1(Composition of the material)	-	0	-
6.1(Wall Construction Designated as Type A)	-	300	-
6.2(Deswignation)	-	0	-
6.3(Dimensions of pipes and fittings)	-	0	-
6.3.1 Table 2(Mean outside diameter)	-	0	-
6.3.2 Table 3(Wall thickness)	-	0	-
6.3.3 Fig 2(Length of pipe)	-	0	-
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	0	-
6.3.4.1(Wall thickness of sockets)	-	0	-
6.3.4.2(Fabricated fittings)	-	0	-
6.3.4.3(Rotational moulded fittings)	-	0	-
6.3.4.4(Type of fittings)	-	0	-
7.1(Appearance)	-	300	-
7.2(Colour )	-	0	-
7.3(Vicat softening temperature of pipes)	-	1100	-
7.4(Resistance to Dichloromethane)	-	1000	-
7.5(longitudinal reversion)	-	950	-
8.1(Appearance and colour)	-	300	-
8.2(Vicat softening temperature of fittings)	-	1400	-
8.3(Effect of Heating (Stress Relief Test))	-	950	-
9.1(Ring stiffness)	-	1400	-
9.2(Resistance to external blows at o C)	-	1400	-
9.3(Ring flexibility)	-	1100	-
9.4(Creep ratio)	-	26300	-
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	1100	-
11.0(Joints)	-	0	-
11.1(Elastomeric Sealing Rings)	-	0	-
11.2(Solvent cement)	-	0	-
12.1(Elastomeric Sealing Ring Joints)	-	1150	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	2300	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.2(Solvent cement joints)	-	1150	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	0	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	2300	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	11300	-

Complete

31 Dec, 2026

IS 16352 (2020)

Geosynthetics – High density polyethylene (HDPE) geomembranes for lining – Specification (first revision)

96560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	300	-
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	250	-
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	1350	-
5,3.1, Table 2,xi) Type I / II / III / IV / V / VI IS 2530(Carbon black content)	-	925	-
5,3.1, Table 2,xii) Type I / II / III / IV / V / VI IS 2530(Carbon black dispersion)	-	700	-
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	54000	Conditioning charges for 90 days at the rate 25/hr by hot air oven
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	750	Length, Width & Asperity Heigths
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	0	-
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	500	Average Thickness + lowest Individual thickness
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	1800	(Test charges 1300 + 500 specimen charges)
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	2200	OIT after ageing (90 days)
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	1100	-
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	12800	(Test charges 300 + Conditioning 12500) for 500 hrs. at the rate 25/hr.
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	1350	(Test charges 1100/- + 250 specimen charges)
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	1350	(Test charges 1100/- + 250 specimen charges)
5,3.1, Table1,iv) a) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield strength,)	-	1600	Test charges 1100/- + 500/- specimen charges
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	1100	-
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	0	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	700	-
3, 3.1(MATERIAL AND MANUFACTURE)	-	2000	-
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	9360	Test charges 1100/- + conditioning / exposure charges 8260 /-
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	2925	CBC+ Material confirmation (925 +2000)
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	0	-
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	0	-
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	0	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	0	-
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	0	-
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	0	-
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	0	-
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	0	-
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	0	-
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	0	-
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	0	-
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	0	-
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	0	-
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	0	-
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	0	-
5,3.1, Table1,iv) a) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield strength,)	-	0	-
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	0	-
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	0	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	0	-
3, 3.1(MATERIAL AND MANUFACTURE)	-	0	-
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	0	-
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	0	-
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	0	-
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	0	-
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	0	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	0	-
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	0	-
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	0	-
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	0	-
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	0	-
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	0	-
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	0	-
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	0	-
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	0	-
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	0	-
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	0	-
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	0	-
5,3.1, Table1,iv) a) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield strength,)	-	0	-
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	0	-
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	0	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	0	-
3, 3.1(MATERIAL AND MANUFACTURE)	-	0	-
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	0	-
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	0	-
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	-	-
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	-	-
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	-	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	-	-
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	-	-
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	-	-
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	-	-
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	-	-
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	-	-
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	-	-
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	-	-
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	-	-
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	-	-
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	-	-
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	-	-
5,3.1, Table1,iv) a) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield strength,)	-	-	-
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	-	-
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	-	-
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	-	-
3, 3.1(MATERIAL AND MANUFACTURE)	-	-	-
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	-	-
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	-	-

Complete

31 Dec, 2026

Revised version of IS 16352:2020. Included w.e.f. 08.08.2023

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

20572 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	250	Nil
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	250	Nil
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	0	Nil
4.2( Netting Fabric)	-	500	Nil
4/4.1(b) percent on avarage value; and( MATERIAL / HDPE Monofilament Yarn)	-	2000	Nil
4/4.1(a) percent on individual value; and( MATERIAL / HDPE Monofilament Yarn)	-	2000	Nil
4.2( Netting Fabric)	-	0	Nil
4.2( Netting Fabric)	-	0	Nil
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	250	Nil
4/4.1.1/60°C / 95°C( MATERIAL / HDPE Monofilament Yarn)	-	1900	Nil
4.3( Colour)	-	300	Nil
6.2(Table-1)	-	17210	Test charges Rs. 7700/- plus specimen & exposure charge Rs.9510/- (25% discount is not applicable in specimen & exposure charges)

Complete

31 Dec, 2026

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

26350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	500	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	11850	Resistant To Hydrostatic Pressure Test for 1000 h(Type test) and Hydrostatic Pressure Test for 1 hr (Acceptence test)
9.2, table -11( Resistance to External Blows at 0 °C)	-	1000	-
7.3( Opacity)	-	575	-
8.2 table-9( Pipe Ends)	-	250	-
5.3(VCM Content)	-	3000	-
5.4( K-Value)	-	1100	-
5.6 / 5.6.1( Material Classification, table -1)	-	0	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	0	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	300	-
7.2( Colour)	-	250	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	500	-
8.1.2, table 4 to 7(Wall Thickness)	-	0	The test charges has already been taken in the cl. no. 8.1.1, 8.1.1.2, table-3 (Dimension of Pipes.
8.1.3 (Length, meter)	-	0	-
8.2 table-9(Dimensions of Integral Socket)	-	300	-
9.3 table-12( Ring Stiffness)	-	1400	-
9.4, annexure-E( Orientation Factor)	-	900	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	1000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	1000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	1000	cl. no. 11.0 (table 13, 14, 15,16) Test : Long Term Pressure testing for assemble joint at 27 degree centigrade - charges 11,000.00 Test : Long Term Pressure testing for assemble joint at 40 degree centigrade - charges 11,000.00
12(a)( ELASTOMERIC SEALS)	-	1050	-
12(b)( ELASTOMERIC SEALS)	-	375	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

18580 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 1(Drop impact strength)	-	1100	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1350	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	4.3 sacks
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	950	4.2,5.1,5.2,5.3,5.4 - Ash content
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	0	4.2,5.1,5.2,5.3,5.4 - Ash content
5.2 Table 1(Ends per dm)	-	250	-
5.2 Table 1(Picks per dm)	-	250	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	2200	4.2,5.1,5.2,5.3,5.4 - Breaking strength after UV exposure (Warp/Weft)
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	2700	4.2,5.1,5.2,5.3,5.4 - Breaking strength before UV exposure (Warp/Weft)
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	10180	UV resistance (192 Hrs.)
5.2 Table 1(Dimensions)	-	750	4.2 Lindear Density + Width of tape
5.2 Table 1(Dimensions)	-	250	4.2,5.1,5.2,5.3,5.4 Mass of sack

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 17216 (2019)

Polyethylene Mulch Films for Agriculture and Horticulture • Specification

617340 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Density)	-	500	-
5.1.2(Melt Flow Index)	-	1100	-
5.1.4(Carbon black, Density)	-	0	-
5.1.4(Carbon black, Toluene extract)	-	0	-
5.1.4(Carbon black, Volatile matter)	-	0	-
5.1.4(Carbon black, particle size)	-	0	-
5.1.4(Carbon black, Tint strength)	-	0	-
5.1.5(UV Stabilizer)	-	2500	-
5.2.1(Visual Appearance)	-	300	-
5.2.2(Film Form)	-	0	-
5.2.4(Odour)	-	250	-
5.3.1.1(Tolerance on thickness)	-	250	-
5.3.1.2(Tolerance on width)	-	250	-
5.3.2(Impact Strength)	-	1350	-
5.3.2, Table 1(Nominal Film Thickness)	-	0	-
5.3.2, Table 1(Impact Failure Mass)	-	0	-
5.3.3(Tensile Strength at Break)	-	2700	-
5.3.4(Elongation at Break)	-	0	The test charges has already been taken in the cl. no. 5.3.3
5.3.5(Coefficient of Friction)	-	850	-
5.3.6(Elmendorf Tear Strength)	-	2000	-
5.3.7(Opacity)	-	575	-
5.4, Table 2(Carbon black, percent)	-	925	-
5.4, Table 2(Ash content, percent)	-	950	-
5.4, Table 2(Carbon black dispersion)	-	700	-
5.5(Service Life)	-	601840	-

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

IS 17358 : Part 1 (2020)

Agro textiles “ Fencing nets for agriculture and horticulture purposes “ Specification Part 1 Fencing nets made from extruded polymer mesh

21410.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, table 1,2,3(MATERIALS)	-	6500.00	6200.00 (Test charge)+ 300.00 (specimen/conditioning charge)
5,/ 5.1( MANUFACTURE (a)Hexagonal shape (see Fig. 1);(b) Diamond shape (see Fig. 2); and c) Square shape (see Fig. 3))	-	0	-
5.2(Colour)	-	250.00	-
6.0(TYPES ,(a)Light duty, b) Medium duty, and c) Heavy duty.)	-	0	-
7.0( REQUIREMENTS)	-	14160.00	5900.00 (Test Charge) + 8260.00 (UV-Exposure of 144 hrs)+ 500.00 (specimen charges of tensile and elongation before UV-exposure)

Complete

31 Dec, 2026

Included w.e.f. 27-05-2022.

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

G SECTOR, GOVINDPURA INDUSTRIAL AREA, J. K. ROAD, BHOPAL, BHOPAL, Bhopal, Madhya Pradesh, 462023

7869955244 cipet.bhopal@gmail.com

Scope List

No Record Found