BIS - LIMS (Laboratory Information Management System)

CIPET, Chennai

TVK industrial area,Guindy, chennai, Chennai, Tamil Nadu, 600032

9480442963 cipetchnptc@gmail.com

Scope List

Reset

27 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Upto 355 mm

511.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	825	25% Discount on Test charges for BIS. GST not included
4(Size of fitting)	-	0	-
5.1 Table-1 Fig.1(Dimension of Socket length)	-	375	25% Discount on Test charges for BIS. GST not included
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	-
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	525	25% Discount on Test charges for BIS. GST not included
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1137.50	25% Discount on Test charges for BIS. GST not included
8(Marking)	-	0	-
3.2.3(socket, measurements)	-	0	-
3.1(Material)	-	0	-
6.3(Effect on water test)	-	2250	25% Discount on Test charges for BIS. GST not included

31 Mar, 2027

-
Included w.e.f. 06.11.2025

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

upto 355mm

142287.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(Classification of pipes)	-	0	-
6.3(Compound Properties)	-	8425	25% Discount on Test charges for BIS. GST not included
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	8750	25% Discount on Test charges for BIS. GST not included
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	525	25% Discount on Test charges for BIS. GST not included
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	375	25% Discount on Test charges for BIS. GST not included
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	0	-
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	0	-
7.1.3 (Effective length)	-	375	25% Discount on Test charges for BIS. GST not included
8(Pipe Ends)	-	375	25% Discount on Test charges for BIS. GST not included
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	375	25% Discount on Test charges for BIS. GST not included
9.1(Visual Appearance)	-	0	-
9.2 IS 12235 (Part 3)(Opacity)	-	525	25% Discount on Test charges for BIS. GST not included
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	2250	25% Discount on Test charges for BIS. GST not included
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	525	25% Discount on Test charges for BIS. GST not included
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	825	25% Discount on Test charges for BIS. GST not included
9.6 IS 12235(Part 14)(Density)	-	525	25% Discount on Test charges for BIS. GST not included
10(Mechanical Properties)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	637.50	25% Discount on Test charges for BIS. GST not included
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	3600	25% Discount on Test charges for BIS. GST not included
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	8250	25% Discount on Test charges for BIS. GST not included
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110250	25% Discount on Test charges for BIS. GST not included
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1325	25% Discount on Test charges for BIS. GST not included
10.4 IS 12235(Part 19)(Flattening Test)	-	875	25% Discount on Test charges for BIS. GST not included
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1475	25% Discount on Test charges for BIS. GST not included
7.1.2(Wall Thickness (Maximum))	-	375	25% Discount on Test charges for BIS. GST not included
7.1.1(Outside Diameter at any point (Maximum))	-	0	-
6.3(K value Test)	-	825	25% Discount on Test charges for BIS. GST not included
6.3.3(Density)	-	525	25% Discount on Test charges for BIS. GST not included
5 Table 1(Classification of pipes)	-	0	-
6.3(Compound Properties)	-	8425	25% Discount on Test charges for BIS. GST not included
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	8750	25% Discount on Test charges for BIS. GST not included
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	525	25% Discount on Test charges for BIS. GST not included
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	375	25% Discount on Test charges for BIS. GST not included
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	-
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	375	-
7.1.3 (Effective length)	-	375	25% Discount on Test charges for BIS. GST not included
8.0(Pipe Ends)	-	375	25% Discount on Test charges for BIS. GST not included
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	375	25% Discount on Test charges for BIS. GST not included
9.1(Visual Appearance)	-	0	-
9.2 IS 12235 (Part 3)(Opacity)	-	525	25% Discount on Test charges for BIS. GST not included
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	2250	25% Discount on Test charges for BIS. GST not included
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	525	25% Discount on Test charges for BIS. GST not included
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	825	25% Discount on Test charges for BIS. GST not included
9.6 IS 12235(Part 14)(Density)	-	525	25% Discount on Test charges for BIS. GST not included
10.0(Mechanical Properties)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	637.50	25% Discount on Test charges for BIS. GST not included
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	3600	25% Discount on Test charges for BIS. GST not included
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	8250	25% Discount on Test charges for BIS. GST not included
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110250	25% Discount on Test charges for BIS. GST not included
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1325	25% Discount on Test charges for BIS. GST not included
10.4 IS 12235(Part 19)(Flattening Test)	-	875	25% Discount on Test charges for BIS. GST not included
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1475	25% Discount on Test charges for BIS. GST not included

31 Mar, 2027

-
Included w.e.f. 06.11.2025 Exclusion: 6.2.1 Annex B (Chloride Content of Resin), 6.3.1 Annex B (Chloride content)

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

uptp 355mm

42537.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	525	25% Discount on Test charges for BIS. GST not included
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	8887.50	25% Discount on Test charges for BIS. GST not included
7.3( Opacity)	-	525	25% Discount on Test charges for BIS. GST not included
9.2, table -11( Resistance to External Blows at 0 °C)	-	1325	25% Discount on Test charges for BIS. GST not included
8.2 table-9( Pipe Ends)	-	1250	25% Discount on Test charges for BIS. GST not included
5 / 5.1(MATERIALS )	-	0	-
5.4( K-Value)	-	825	25% Discount on Test charges for BIS. GST not included
5.6 / 5.6.1( Material Classification, table -1)	-	0	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	0	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	0	-
7.2( Colour)	-	375	25% Discount on Test charges for BIS. GST not included
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	375	25% Discount on Test charges for BIS. GST not included
8.1.2, table 4 to 7(Wall Thickness)	-	375	25% Discount on Test charges for BIS. GST not included
8.1.3 (Length, meter)	-	0	-
8.2 table-9(Dimensions of Integral Socket)	-	375	25% Discount on Test charges for BIS. GST not included
9.3 table-12( Ring Stiffness)	-	1250	25% Discount on Test charges for BIS. GST not included
9.4, annexure-E( Orientation Factor)	-	1025	25% Discount on Test charges for BIS. GST not included
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	0	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	17250	25% Discount on Test charges for BIS. GST not included Long term test 11.1 & 11.3
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	750	25% Discount on Test charges for BIS. GST not included
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	750	25% Discount on Test charges for BIS. GST not included
12(a)( ELASTOMERIC SEALS)	-	1500	25% Discount on Test charges for BIS. GST not included
12(b)( ELASTOMERIC SEALS)	-	375	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	825	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/2(Effect on Water)	-	2250	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	750	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	975	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	825	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/2(Effect on Water)	-	2250	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	750	25% Discount on Test charges for BIS. GST not included
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	1475	25% Discount on Test charges for BIS. GST not included

31 Mar, 2027

-
Included w.e.f. 06.11.2025 Exclusion: 5.3 (VCM Content)

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

upto 315mm

27162.5 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	375	25% Discount on Test charges for BIS. GST not included
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	0	-
6.1.3 (Length of Pipe)	-	375	25% Discount on Test charges for BIS. GST not included
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	375	25% Discount on Test charges for BIS. GST not included
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	-
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	-
6.1.4.1 (e3min=0.75e)	-	0	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	-
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	-
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	-
7(Physical characteristics )	-	375	25% Discount on Test charges for BIS. GST not included
7.1(Appearance:- )	-	0	-
7.1(Appearance:- )	-	0	-
7.2(Colour )	-	375	25% Discount on Test charges for BIS. GST not included
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	825	25% Discount on Test charges for BIS. GST not included
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1025	25% Discount on Test charges for BIS. GST not included
8(MECHANICAL CHARACTERISTICS)	-	0	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1325	25% Discount on Test charges for BIS. GST not included
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1325	25% Discount on Test charges for BIS. GST not included
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	638.50	25% Discount on Test charges for BIS. GST not included
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	8250	25% Discount on Test charges for BIS. GST not included
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	375	25% Discount on Test charges for BIS. GST not included
9.2 IS 14182(b) Solvent cement)	-	8262.50	25% Discount on Test charges for BIS. GST not included
10(Performance requirements)	-	0	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	637.50	25% Discount on Test charges for BIS. GST not included
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	750	25% Discount on Test charges for BIS. GST not included
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	637.50	25% Discount on Test charges for BIS. GST not included
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	750	25% Discount on Test charges for BIS. GST not included
'7.5 (amdt.7)(Effect on Water (Type test))	-	2250	25% Discount on Test charges for BIS. GST not included
5.3(Qualitative)	-	0	-
12(Marking)	-	0	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	-

31 Mar, 2027

-
Included w.e.f. 04.11.2025 Exclusion: 5,5.2 (Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)

IS 17953 (2023)

uPVC Profiles for Windows And Doors Specification

All

300750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5.1.1(UV Resistant Virgin Material)	-	2650	25% Discount on Test charges for BIS. GST not included
Cl. No.5.1.2(Non-UV Resistant Virgin Material)	-	2650	25% Discount on Test charges for BIS. GST not included
Cl.No.5.2(Appearance of uPVC Profile)	-	1325	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.1and3.2.5, Table no. 2(i)(Depth (D))	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.1and3.2.5, Table no. 2(ii)(Width (W))	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.1and3.2.5, Table no. 2(iii)("Sight visible surface wall thickness, Max ")	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.1and3.2.5, Table no. 2(iv)("Sight visible surface flatness, Max ")	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.1and3.2.5, Table no. 2(v)(Parallelism, Max)	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.2(Wall Thickness of Main Profiles)	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.3(Tolerances on other Dimensions)	-	0	25% Discount on Test charges for BIS. GST not included
Cl.No.5.3.4(Straightness)	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.4(Mass of Profile)	-	375	25% Discount on Test charges for BIS. GST not included
Cl.No.5.5("Heat Reversion ")	-	1025	25% Discount on Test charges for BIS. GST not included
Cl.No.5.6(Resistance to Impact of Falling Mass)	-	1325	25% Discount on Test charges for BIS. GST not included
Cl.No.5.7(Heat Ageing)	-	1025	25% Discount on Test charges for BIS. GST not included
Cl.No.5.8.1(Tensile Bending Test)	-	1950	25% Discount on Test charges for BIS. GST not included
Cl.No.5.8.2(Compression Bending Test)	-	1950	25% Discount on Test charges for BIS. GST not included
Cl.No.5.9.(Charpy Impact Resistance of Main Profile)	-	1325	25% Discount on Test charges for BIS. GST not included
Cl.No.5.10.(Resistance to Weathering)	-	284150	25% Discount on Test charges for BIS. GST not included Weathering Exposure for 1600 hrs - Rs.281500, for 3300 hrs -RS. 579000 for 8000 hrs -Rs. 1401500 After exposure 1. impact strength -RS .1325 2. Colour Fastness - RS.1325
Cl.No.5.11(Density)	-	1025	25% Discount on Test charges for BIS. GST not included
Cl.No.8(Marking)	-	0	-
Cl. No.5.1.1(UV Resistant Virgin Material)	-	-	-
Cl. No.5.1.2(Non-UV Resistant Virgin Material)	-	-	-
Cl.No.5.2(Appearance of uPVC Profile)	-	-	-
Cl.No.5.3.1and3.2.5, Table no. 2(i)(Depth (D))	-	-	-
Cl.No.5.3.1and3.2.5, Table no. 2(ii)(Width (W))	-	-	-
Cl.No.5.3.1and3.2.5, Table no. 2(iii)("Sight visible surface wall thickness, Max ")	-	-	-
Cl.No.5.3.1and3.2.5, Table no. 2(iv)("Sight visible surface flatness, Max ")	-	-	-
Cl.No.5.3.1and3.2.5, Table no. 2(v)(Parallelism, Max)	-	-	-
Cl.No.5.3.2(Wall Thickness of Main Profiles)	-	-	-
Cl.No.5.3.3(Tolerances on other Dimensions)	-	-	-
Cl.No.5.3.4(Straightness)	-	-	-
Cl.No.5.4(Mass of Profile)	-	-	-
Cl.No.5.5("Heat Reversion ")	-	-	-
Cl.No.5.6(Resistance to Impact of Falling Mass)	-	-	-
Cl.No.5.7(Heat Ageing)	-	-	-
Cl.No.5.8.1(Tensile Bending Test)	-	-	-
Cl.No.5.8.2(Compression Bending Test)	-	-	-
Cl.No.5.9.(Charpy Impact Resistance of Main Profile)	-	-	-
Cl.No.5.10.(Resistance to Weathering)	-	-	-
Cl.No.5.11(Density)	-	-	-
Cl.No.8(Marking)	-	-	-

31 Mar, 2027

-
Included w.e.f. 29.10.2025 Exclusion: "Cl. No.5.1.3, a), Table no. 1(i) (Monoextrusion or coextrusion of a layer of any visible surface) Cl. No.5.1.3, a), Table no. 1(ii) (""Non-visible surface and material covered by coextrusion"") Cl. No.5.1.1 (UV Resistant Virgin Material)"

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

All type

18731.25 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	525	25% Discount on Test charges for BIS. GST not included
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	693.75	25% Discount on Test charges for BIS. GST not included
5.1.6(Ash content - IS 2508: 2024)	-	900	25% Discount on Test charges for BIS. GST not included
5.1.6(carbon black dispersion - IS 2530: 1963)	-	525	25% Discount on Test charges for BIS. GST not included
5.1.1(Appearance)	-	375	25% Discount on Test charges for BIS. GST not included
5.1.2(Film Form)	-	375	25% Discount on Test charges for BIS. GST not included
5.1.3(Odour)	-	375	25% Discount on Test charges for BIS. GST not included
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	825	25% Discount on Test charges for BIS. GST not included
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	375	25% Discount on Test charges for BIS. GST not included
5.2.1.2(Nominal Width)	-	375	25% Discount on Test charges for BIS. GST not included
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	5675	25% Discount on Test charges for BIS. GST not included
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	637.5	25% Discount on Test charges for BIS. GST not included
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1325	25% Discount on Test charges for BIS. GST not included
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1325	25% Discount on Test charges for BIS. GST not included
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	5675	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	637.5	25% Discount on Test charges for BIS. GST not included
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1325	25% Discount on Test charges for BIS. GST not included
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	825	25% Discount on Test charges for BIS. GST not included
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1475	25% Discount on Test charges for BIS. GST not included
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	25% Discount on Test charges for BIS. GST not included
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	0	25% Discount on Test charges for BIS. GST not included
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	0	25% Discount on Test charges for BIS. GST not included
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1325	25% Discount on Test charges for BIS. GST not included

31 Mar, 2027

-
Included w.e.f.08.10.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

All Sse

9868.75 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	1500	25% Discount on Test charges for BIS. GST not included
4.2(a)(Carbon Black Content-IS 2530)	-	693.75	25% Discount on Test charges for BIS. GST not included
4.2(b)(Carbon Black Dispersion-IS 2530)	-	525	-
Cl-6.0(Visual Appearance)	-	375	25% Discount on Test charges for BIS. GST not included
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	2250	25% Discount on Test charges for BIS. GST not included
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	750	25% Discount on Test charges for BIS. GST not included
Cl-7.2(Reversion Test)	-	1025	25% Discount on Test charges for BIS. GST not included
7.3(Tensile Strength)	-	1475	25% Discount on Test charges for BIS. GST not included
7.3(Elongation at Break)	-	0	25% Discount on Test charges for BIS. GST not included
7.4(SusceptibiIity to Environmental Stress Cracking)	-	900	25% Discount on Test charges for BIS. GST not included
Cl-9.0(Coiling)	-	0	25% Discount on Test charges for BIS. GST not included
Cl-4.2(Carbon content of finished PE lateral pipe)	-	693.75	25% Discount on Test charges for BIS. GST not included
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	375	25% Discount on Test charges for BIS. GST not included
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	375	25% Discount on Test charges for BIS. GST not included
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	375	25% Discount on Test charges for BIS. GST not included
Cl-7.3(Tensile Test)	-	1475	25% Discount on Test charges for BIS. GST not included
Cl-7.3.1(Test Piece)	-	0	25% Discount on Test charges for BIS. GST not included
Cl-7.3.2(Procedure)	-	0	25% Discount on Test charges for BIS. GST not included
Cl-8.0(Supply of pipes)	-	0	25% Discount on Test charges for BIS. GST not included
Cl-10.0(Sampling and criteria for conformity)	-	0	25% Discount on Test charges for BIS. GST not included
Cl-11(Marking)	-	0	25% Discount on Test charges for BIS. GST not included
3(Class of Pipe)	-	0	25% Discount on Test charges for BIS. GST not included
6(Visual Appearance)	-	375	25% Discount on Test charges for BIS. GST not included
7.1 & Table 2(Hydraulic Characteristics)	-	750	25% Discount on Test charges for BIS. GST not included
7.1 & Table 2(Hydraulic Characteristics)	-	2250	25% Discount on Test charges for BIS. GST not included
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	900	25% Discount on Test charges for BIS. GST not included
7.2(Reversion Test)	-	1025	25% Discount on Test charges for BIS. GST not included

31 Mar, 2027

-
Included w.e.f.08.10.2025

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

All

3193.75 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	1150	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.2(MFI)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.5.6 IS 2530(Carbon black dispersion)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.4.3 10 ofIS 2530(Carbon black content)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 10151 (2019)

Polyvinyl chloride (Pvc) and its copolymers for its safe use in contact with foodstuffs, pharmaceuticals and drinking water - Specification (First Revision)

all

4625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4(Monomer content)	-	2625		Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.5(Overall Migration, IS 9845)	-	2000		Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 12252 (2017)

Polyalkylene terephthalates (Pet And Pbt), their copolymers and list of constituents in raw materials and end products for their safe use in contact with foodstuffs and pharmaceuticals (First Revision)

all

2688 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3(Overall Migration,Max)	-	1900		After 25% discount on test charges for BIS Identification Charges -787.5

31 Mar, 2027

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

upto 1 mm

16731 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2(Film Form)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.3(Odour)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6a(Carbon Black Content, Annex-A)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6b(Ash Content, Annex-A)	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.2(Tolerance on Thickness, Annex-A)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	637.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1, Table 1(Tear resistence. B) Transverse direction )	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	637.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Tear resistance , Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1, Table 3(Puncture resistance , Annex C)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Tear resistance , Annex B)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.1, Table 4(Puncture resistance , Annex C)	-	925	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	975	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.1(Nominal Thickness)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2.1.2(Nominal width)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

upto 315 mm diameter

17662.5 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	4475	Exposure charges Effect on Sunlight Rs. 3500/- Tensile Strength After Exposure RS. 1475/- Testing Charges after 25% concession( GST Extra as applicable)
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1325	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	637.5	Testing Charges after 25% concession( GST Extra as applicable)
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	750	Effect on water - Rs.2250/- Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

upto 355mm diameter

20013 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(PVC Resin)	-	3075	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	187.50	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
9.1(PIPE ENDS)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
10.3(Effect on Water Test)	-	2250	Testing Charges after 25% concession( GST Extra as applicable)
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
10.7(Sulphated Ash Content)	-	900	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	8250	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	8250	Testing Charges after 25% concession( GST Extra as applicable)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	637.50	Testing Charges after 25% concession( GST Extra as applicable)
11.2(Resistance to External Blows at 0°C)	-	1250	Testing Charges after 25% concession( GST Extra as applicable)
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7.1.4(Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

upto 200mm

12900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
4.1.2(K-Value as per IS-4669)	-	825	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
5(COLOUR)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.1(No.of Ribs)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.2(Rib height)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4(Sealing rings - Hardness)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.1(Visual Appearance)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.2(Internal Diameter)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.3(Density IS 12235 (Part 14))	-	525	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.5(Tensile Strength IS 12235(Part 13))	-	1475	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	825	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Upto 355 mm

40824.75 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
6.2.1(6.1.1 Identification Stripes)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
7()	-	0	Testing Charges after 25% concession( GST Extra as applicable)
7.2(Length)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	562.5	Testing Charges after 25% concession( GST Extra as applicable)
7.4.1.2(Ovality)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	16550	Testing Charges after 25% concession( GST Extra as applicable)
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1200	Testing Charges after 25% concession( GST Extra as applicable)
8.2(Longitudinal Reversion Test)	-	1025	Testing Charges after 25% concession( GST Extra as applicable)
8.3(Carbon black)	-	1218.75	Testing Charges after 25% concession( GST Extra as applicable)
8.4( Melt Flow Rate)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
8.5 (Oxidation Induction Time)	-	1650	Testing Charges after 25% concession( GST Extra as applicable)
8.6(Overall migration)	-	1775	Testing Charges after 25% concession( GST Extra as applicable)
8.7(Density)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
8.8(Tensile Strength for Butt-fusion)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
8.9 table-6(Elongation at Break)	-	1475	Testing Charges after 25% concession( GST Extra as applicable)
8.10(Slow Crack Growth Rate)	-	4625	Testing Charges after 25% concession( GST Extra as applicable)
5, 5.1 table-1(MATERIALS)	-	0	Testing Charges after 25% concession( GST Extra as applicable)
5.2(Polyethylene Resin)	-	4675	Testing Charges after 25% concession( GST Extra as applicable)
5.3(d)(Carbon Black Master Batch)	-	1218.75	Testing Charges after 25% concession( GST Extra as applicable)
5.3(e)(Carbon Black Master Batch)	-	900	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
-

IS 9537 : Part 5 (2000)

Conduits four electrical installations - Part 5 pliable conduits of insulating material

All type

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimension)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
8(Construction)	-	375	Testing Charges after 25% concession( GST Extra as applicable)
9.2(Bending Test)	-	750	Testing Charges after 25% concession( GST Extra as applicable)
9.3(Compression Test)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
9.5(Callapse Test)	-	825	Testing Charges after 25% concession( GST Extra as applicable)
10(Resistance to heat)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
11(Resistance to burning)	-	525	Testing Charges after 25% concession( GST Extra as applicable)
12(Electrical characteristics)	-	2650	Testing Charges after 25% concession( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 01-09-2017.

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

all

12825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.2.2(Fittings)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.3(General)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.1(Wall Thickness ofEmitting Pipe)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.3(Flow Paths in Emitting Unit)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.3.4(Spacing ofEmitter Units)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.5(Resistance to Tension at Elevated Temperature)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1200	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.8(Determination of Emitting Unit Exponent)	-	450	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	787.5	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

All

25292.5 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1275	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1050	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.3.1(Bottom seam (IS 10789))	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 ii(Dimensions )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2 and Table 1 iii(Ends per dm )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.2 and Table 1 iv(Picks per dm )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 v(Mass of sack )	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1650	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	11830	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2 and Table 1 x(Ash content )	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(MFI)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.2(Density)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.1(Overall Migration)	-	1275	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 2533 (1978)

Specification for geometry boxes (First Revision)

all

19125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(MATERIALS)	-	9000	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Cl. No.5, Table no.1and 2(DIMENSIONS AND TOLERANCES)	-	6750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Cl. No.6(GRADUATIONS)	-	3375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 19-09-2017.

IS 9537 : Part 1 (1980)

Specification for conduits for electrical installations: Part 1 general requirements

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8(Constrution)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9 & 9.2("Mechanical properties Bending test ")	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.3(Compression test)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.4(Impact test)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.5(Collapse test)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
10(Resistance to heat)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
11(Resistance to burning)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Electrical strength test & Insulation resistance test)	-	2650	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
Included w.e.f. 01-09-2017.

IS 10146 (1982)

Specification for polyethylene for its safe use in contact with foodstuffs, pharmaceuticals and drinking water zy

All

2688 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2(Material )	-	787.50		Testing Charges after 25% concession for BIS ( GST Extra as applicable)
3.4(Overall Migration)	-	1900		Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

All

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Maximum and minimum outside diameter of socket)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1.1 Table-2(Length of Socket end)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1.2(Maximum and minimum outside diameter of conduit)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.2(Minimum inside diameter of conduit)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.3(Length of conduit)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.4(Unifomity of The wall Thickness)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.2(Bending Test At Room Temp)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
10(Resistance to Heat -Ball presure test)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.2(Bending Test At Low Temp (-5 ±2°C))	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 9537 : Part 4 (1983)

Specification for conduits for electrical installations: Part 4 pliable self - Recovering conduits of insulating materials

All

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Dimensions, (Minimum outside Diameter), IS 9537-4)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1(Dimensions (Maximum outside Diameter), IS 9537-4)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.3.3(Uniformity of wall thickness, IS 9537-4)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
8.1(Construction, Cl. 8 of IS 9537-1)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.3(Mechanical Properties (Compression Test), IS 9537-4)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.4(Mechanical Properties (Impact Test), Cl. 9.4 of IS 9537-1)	-	825	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
9.5(Mechanical Properties (Collapse Test), IS 9537-4)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
10(Resistance to heat)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
11(Resistance to burning, Cl. 11 of IS 9537-1)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Electrical Strength, Cl. 12.1.1 of IS 9537-1)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
12(Insulation Resistance, Cl. 12.1.2 of IS 9537-1)	-	1325	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

All

7388 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.1(Stress Relief Test- Appendix A)	-	525	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.2(Opacity- Appendix B)	-	525	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	637.50	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
6.3(Effect on Water)	-	2250	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
6.1.1(VCM Content Test)	-	3075	Testing Charges after 25% concession to BIS ( GST Extra as applicable) K Value - 825 VCM content 2250

31 Mar, 2027

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

upto 32mm

11650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.0 5.1 (Table1) (b)Tolerance on OD)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
6.1(Visual Appearance)	-	375	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	2250	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.2(Reversion Test)	-	1025	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.3(Tensile Test)	-	1475	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.3(Elongation at Break)	-	0	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
7.4(SusceptibiIity to Environmental Stress Cracking)	-	900	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.1.a (Potyethylene - higher olefins constituent )	-	787.50	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.1.c.ii (Toluene extract - Annex A)	-	750	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
4.1.c.iii (Volatile matter - Annex B )	-	525	Testing Charges after 25% concession for BIS ( GST Extra as applicable)
Cl. 4.2(Carbon Black Content)	-	693.75	Testing Charges after 25% concession for BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

All

3825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.2(Flow path in emitters)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.1(Resistance to Hydrostatic pressure)	-	750	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.2(Resistance to Hydrostatic pressure)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.3.3(Resistance to Hydrostatic pressure)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4.1(Emitter Pull Out In-line emitters)	-	375	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
7.4.2(Emitter Pull Out On-line emitters)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	750	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	750	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	750	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	750	Testing Charges after 25% concession to BIS ( GST Extra as applicable)
8.3(Determination of Emitter Exponent)	-	450	Testing Charges after 25% concession to BIS ( GST Extra as applicable)

31 Mar, 2027

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

0 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 )	-	-
table 1 sl.no: 02(20 )	-	-
table 1 sl.no: 03(25 )	-	-
table 1 sl.no: 04(32 )	-	-
table 1 sl.no: 05(40 )	-	-
table 1 sl.no: 06(50 )	-	-
table 1 sl.no: 07(63 )	-	-
table 1 sl.no: 08(75 )	-	-
table 1 sl.no: 09(90 )	-	-
table 1 sl.no: 10(110 )	-	-
table 1 sl.no: 11(125 )	-	-
table 1 sl.no: 12(140 )	-	-
table 1 sl.no: 13(160 )	-	-
table 1 sl.no: 14( 180 )	-	-
table 1 sl.no: 15(200 )	-	-
table 1 sl.no: 16(225 )	-	-
table 1 sl.no: 17(250.0)	-	-
table 1 sl.no: 18(280.0)	-	-
table 1 sl.no: 19(315.0)	-	-
2.1(General)	-	-
2.2(Manufacture)	-	-
2.2.2, Table 1(Size)	-	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	-
2.2.3( inside diameter of the socket)	-	-
2.2.3(socket length)	-	-
2.1(General)	-	-
2.2(Manufacture)	-	-
2.2.2, Table 1(Size)	-	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	-
2.2.3( inside diameter of the socket)	-	-
2.2.3(socket length)	-	-
6.4 PART-1(Short term hydraulic test)	-	-
6.1.1(VCM Content Test)	-	-
2.2.2 table 1(Laying Length)	-	-
6.4 PART-1(Short term hydraulic test)	-	-
6.1.1(VCM Content Test)	-	-
2.2.2 table 1(Laying Length)	-	-

31 Mar, 2027

-
Included w.e.f 16.09.2025

Bureau of Indian Standards

The National Standards Body of India

CIPET, Chennai

TVK industrial area,Guindy, chennai, Chennai, Tamil Nadu, 600032

9480442963 cipetchnptc@gmail.com

Scope List