BIS - LIMS (Laboratory Information Management System)

POLYMER TESTING LABORATORY, CIPET:SARP-APDDRL

PLOT NO.- 7P, HI TECH DEFENCE & AEROSPACE PARK (IT SECTOR), Bangalore, Bengaluru Rural, Karnataka, 562149

9840376907 apddrl@cipet.gov.in

Scope List

Reset

10 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16008 : Part 1 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 1 Shade nets made from tape yarns (first revision)

39560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Types)	-	1000	-
6.1(Dimensions and Mass - IS 1954)	-	1000	-
6.1(Dimensions and Mass - IS 1954)	-	0	-
6.2 Table 1(Mass - IS 1964)	-	0	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	2200	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	2200	-
6.2 Table 1(Retention of breaking strength after UV exposure - IS 1969 (Part 1))	-	8260	-
6.2 Table 1(Colour fastness to artificial light, IS 2454)	-	19850	-
6.2 Table 1(Bursting Pressure, IS 1966 (Part 1 or 2))	-	1000	-
6.2 Table 1(Shading Percentage)	-	700	-
4.3, 4(Colour)	-	500	-
4.2, 4(Fabric )	-	500	-
4.1.1, 4(HDPE Tapes Heat shrinkage )	-	700	-
4.1, 4( HDPE Tapes Linear density )	-	700	-
4.1, 4(HDPE Tapes Width )	-	0	-
4.1, 4(HDPE Tapes UV stabilizer)	-	2500	-
4.1, 4(HDPE Tapes Material Identification )	-	2000	-

26 Aug, 2028

-
-

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

72019 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4( Line/ Cord beading IS 7903)	-	500	-
4.0(Types IS 7903)	-	0	-
5.1.1(Lamination IS 7903)	-	0	-
5.1.2(Lamination IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	500	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.3(Joint/Seam, IS 7903)	-	500	-
5.4(Fixing of Eyelets, IS 7903)	-	0	-
5.4(Fixing of Eyelets ,IS 7903)	-	0	-
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	0	-
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0	-
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	0	-
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	500	-
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	0	-
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	1100	-
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	1100	-
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0	-
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0	-
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	27750	UV exposure by xenon arc condition
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	0	-
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	0	-
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	0	-
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100	-
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100	-
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100	-
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	19850	-
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950	-
6.2(Length, IS 7903)	-	500	-
6.2(Width, IS 7903)	-	0	-
6.2(height, IS 7903)	-	0	-
6.3(Water Proofness,IS 7941)	-	1000	-
6.3(Water Proofness, IS 7940)	-	5200	-
3.4( Line/ Cord beading IS 7903)	-	0	-
4.0(Types IS 7903)	-	0	-
5.1.1(Lamination IS 7903)	-	0	-
5.1.2(Lamination IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.2.1(Construction IS 7903)	-	0	-
5.3(Joint/Seam, IS 7903)	-	0	-
5.4(Fixing of Eyelets, IS 7903)	-	0	-
5.4(Fixing of Eyelets ,IS 7903)	-	0	-
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	0	-
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0	-
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	0	-
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	0	-
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	0	-
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	0	-
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	0	-
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0	-
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0	-
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	0	-
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	0	-
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	0	-
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	0	-
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	0	-
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	0	-
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	0	-
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	0	-
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	0	-
6.2(Length, IS 7903)	-	0	-
6.2(Width, IS 7903)	-	0	-
6.2(height, IS 7903)	-	0	-
6.3(Water Proofness,IS 7941)	-	0	-
6.3(Water Proofness, IS 7940)	-	0	-
6.2(dimension(l))	-	0	-
6.2(dimension(w))	-	0	-
6.2(dimension(h))	-	0	-
3.3(Eyelets (Dimesnions) i) Starting thickness of metal Aluminium min ii) Outside dia of flange‘A’ iii) Flange formed height ‘B’ iv) Pierced dia ‘C’ v) Overall length ‘D’ vi) Internal dia of Barrel when closed ‘E’ min vii) Thickness of compressed material between eyelet and washer F’ max viii) Outside diameter of barrel under the flange‘G’ )	-	0	-
3.3(Eyelets)	-	0	-
3.2(HDPE Fabric (Material Identification))	-	0	-
3.1(HDPE Tapes (Carbon Black Content))	-	0	-
3.1(HDPE Tapes (Presence of UV-stabiliser))	-	0	-
3.1(HDPE Tapes (Material Identification))	-	0	-
3.1()	-	0	-
3.1()	-	0	-
3.1()	-	0	-
3.1()	-	0	-
3.1()	-	0	-
4()	-	0	-
5.1.1(Coating Thickness)	-	0	-
5.1.1(Carbon Black Content)	-	0	-
5.1.1(Sandwich lamination thickness)	-	0	-
5.1.1(Mass of Finished Tarpaulin)	-	0	-
5.1.1(UV Exposure (144 hrs))	-	0	-
5.1.1(Agening)	-	0	-
7(Marking)	-	0	-

26 Aug, 2028

-
-

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

5100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	500	-
7.2(Flow path in emitters)	-	500	-
7.3.1(Resistance to Hydrostatic pressure)	-	1000	-
7.3.2(Resistance to Hydrostatic pressure)	-	0	-
7.3.3(Resistance to Hydrostatic pressure)	-	0	-
7.4.1(Emitter Pull Out In-line emitters)	-	500	-
7.4.2(Emitter Pull Out On-line emitters)	-	0	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1000	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	1000	-
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	0	-
8.3(Determination of Emitter Exponent)	-	600	-
4(Classification)	-	0	-
5.1(Connections)	-	0	-
5.2(Emitter Ends)	-	0	-
5.3(Materials)	-	0	-
6.1(Test Specimens)	-	0	-
6.2(Test Conditions)	-	0	-
6.3(Accuracy or Measuring Devices)	-	0	-
7.1(Construction and Workmanship)	-	0	-
7.2(Flow Paths In Emitter)	-	0	-
7.3(Resistance to Hydrostatic Pressure)	-	0	-
7.4(Emitter Pull-out)	-	0	-
7.4.1(In-Line Emitters)	-	0	-
7.4.2(On-Line Emitters)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.1(Number of Test Samples)	-	0	-
8.1.2(Unregulated Emitters)	-	0	-
8.1.3(Regulated Emitters)	-	0	-
8.2(Emission Rate as a Function of Inlet Pressure)	-	0	-
8.2.1(Selection of Telt Sample)	-	0	-
8.2.2(Unregulated Emttters)	-	0	-
8.2.3(Regulated Emitters)	-	0	-
8.3(Determiaatlon of Emitter Exponent)	-	0	-
9(Marking)	-	0	-

26 Aug, 2028

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

22425 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	-
4.2.3(Carbon Dispersion Test)	-	700	-
5(Types and Features )	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	5000	inlude cl 5.1,5.2,5.3 and 5.4 dimensions
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	-
5.3(Types and Features )	-	0	-
5.6(Types and Features )	-	0	-
6.1(Finish)	-	500	-
7.1.1(Resistance to Deformation)	-	700	-
7.1.2(Resistance to Deformation)	-	0	-
7.2(Resistance to Impact)	-	1000	-
7.3(Test for Top Load Resistance)	-	900	-
7.4(Tensile Strength)	-	1800	500 specimen preparation charges(inclusive)
7.5(Flexural Modulus)	-	1600	500 specimen preparation charges(inclusive)
7.6(overall Migration)	-	2200	500 specimen preparation charges(inclusive)
9.2.1(Man-Hole and Hand-Hole Lids)	-	1050	-
9.1(Man-Hole and Hand-Hole Lids)	-	500	visaul appearnce
9.2(Man-Hole and Hand-Hole Lids)	-	500	-
9.1(Lid Thickness)	-	0	-
7.3(Test for Top Load Resistance)	-	0	-
6.1(Finish)	-	0	-
5.4(Wall Thickness above effective height)	-	0	-
5.2 Table 2 (7)(Minimum Wall Thickness)	-	0	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	0	-
4.2.1(Density)	-	1325	specimen preparation charges(inclusive)
4.2.2(MFI)	-	1100	-
7.6(overall Migration)	-	0	-
4.1(MATERIALS)	-	0	-
4.2.2(MFR)	-	0	-
4.2.1(Density)	-	0	-
5.4(Wall Thickness)	-	0	-
10(MARKING)	-	0	-
Cl-7.6(Overall Migration)	-	0	-

26 Aug, 2028

-
-

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

9544 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	500	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	500	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1100	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	700	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
6.2.2(Fittings)	-	0	-
6.3(General)	-	0	-
6.3(General)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	1000	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	500	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	Included in 8.3.1
8.3.3(Flow Paths in Emitting Unit)	-	500	-
8.3.4(Spacing ofEmitter Units)	-	0	included in 8.3.3
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600	-
8.5(Resistance to Tension at Elevated Temperature)	-	1100	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	entered in 8.5
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	500	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1200	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1600	-
8.8(Determination of Emitting Unit Exponent)	-	600	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	0	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0	-
4.2(Carbon black content)	-	0	-
4.2(Carbon black dispersion)	-	0	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	500	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0	-
6.2(Fittings)	-	0	-
6.3(General)	-	0	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-

26 Aug, 2028

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

8369 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	0	-
4.1.b(Potyethylene - anti-oxidant)	-	0	-
4.1.c.i (Density)	-	625	-
4.1.c.ii (Toluene extract - Annex A)	-	1100	-
4.1.c.iii (Volatile matter - Annex B )	-	700	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
4.3(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
7.3(Tensile Test)	-	1800	including specimen preparation
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	500	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
7.2(Reversion Test)	-	1200	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
7.2(Reversion Test)	-	0	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
7.2(Reversion Test)	-	0	-
7.1(Hydraulic Characteristics)	-	1000	acceptance test
7.1(Hydraulic Characteristics)	-	3000	type test
6.1(Visual Appearance)	-	500	-
3.1(Class of Pipe)	-	0	-
9.0 (9.1)(Minimum Internal Diameter of Coil)	-	0	-
9.0 (9.1)(Coiling )	-	0	-
8.0 (8.1) (Supply of pipes )	-	0	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	0	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	0	-
6.0 (6.1) (Visual appearance)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0	-
5.0 5.1 (Table1) (b)Tolerance on OD)	-	0	-
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	0	-
Cl. 4.2(Carbon Black Content)	-	0	-
Cl. 4.2(Carbon Black Dispersion)	-	0	-
Cl. 5.0 & 5.1 Table -1(Outside Diameter)	-	0	-
Cl. 5.0 & 5.1 Table -1(,Tolerence,)	-	0	-
Cl. 5.0 & 5.1 Table -1(Wall Thckness)	-	0	-
Cl. 7.1 Table -2(Quality Test for 100 hrs @ 70 c & 2.2 Mpa)	-	0	-
Cl. 7.1 Table -2(Acceptance Test for 1 hrs @ 27 c & 6.9 Mpa)	-	0	-
Cl. 7.3(Tensile Test)	-	0	-
Cl. 7.3(Elongation)	-	0	-
Cl. 8.0- 8.1(Supply of pipes)	-	0	-
Cl. 9.0 - 9.1(Minimum Internal Diameter of Coil)	-	0	-
4.1.c(iv)(MATERIAL)	-	0	-
4.1d(MATERIAL)	-	0	-
4.2a(Carbon Black Content)	-	0	-
7.4(SusceptibiIity to Environmental Stress)	-	0	-
4(MATERIAL)	-	0	-
5.1(Diameters and wall thicknesses)	-	0	-
6(VISUAL APPEARANCE)	-	0	-
7.1(Hydraolic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Test)	-	0	-
7.3.1(Test Piece)	-	0	-
7.3.2(Procerdure)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
8(SUPPLY OF PIPES)	-	0	-
9(COILING)	-	0	-
11(Marking)	-	0	-

26 Aug, 2028

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

18618 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	900	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	900	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.3.1(Bottom seam (IS 10789))	-	500	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	INCLUDED WITH ELONGATION
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	1100	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	Included with elongation
4.2 and Table 1 x(Ash content )	-	1200	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	0	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.3.1(Bottom seam (IS 10789))	-	500	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1100	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	included with elongation
4.2 and Table 1 viii(Elongation at break of fabric )	-	1100	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.2 and Table 1 x(Ash content )	-	1200	-
3.1(Material Identification)	-	2000	-
3.1(Overall Migration)	-	1700	-
3.2(Density)	-	500	-
3.2(MFI)	-	1100	-

26 Aug, 2028

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

24400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	500	-
10.1(Surface Finish)	-	0	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	-
10.7(Sulphated Ash Content)	-	1200	-
5(CLASSIFICATION OF PIPES)	-	0	-
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	Included in cl 7
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	Included in cl 7
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	Included in cl 7
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	Included in cl 7
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	Included in cl 7
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Included in cl 7
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	Included in cl 7
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Included in cl 7
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Included in cl 7
7.2.1(DIMENSIONS-Socket)	-	0	Included in cl 7
7.2.1(DIMENSIONS-Socket)	-	0	Included in cl 7
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	Included in cl 7
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	Included in cl 7
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	Included in cl 7
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	Included in cl 7
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	Included in cl 7
8(SEALING RINGS)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	Included in cl 10
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	Included in cl 10
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	700	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1200	Test Specimen preparation charges inclusive
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	Type test (1000 hr/60 deg C)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	Acceptance test (1 hr/27 deg C)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	Type test (1000 hrs /27 deg C)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	Acceptance test (1 hr/27 deg C)
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	included in cl 11.1
11.2(Resistance to External Blows at 0°C)	-	1500	Test Specimen preparation charges inclusive
10.3(Effect on Water Test)	-	3000	-
6.1.2(PVC Resin)	-	3075	Composition VCM Content K - Value
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	0	Included in cl 7.0
7.1.4(Length)	-	0	Included in cl 7.0
6.1.1(VCM Content)	-	0	Included in cl 6.1.2
7.2.1.2b(Maximum inner diameter of groove)	-	0	Included in cl 7.0
13.1(Marking)	-	0	Included in cl 10.1

26 Aug, 2028

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

36275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000	Specimen preparation charges inclusive
8.9 table-6(Elongation at Break)	-	1800	-
8.8(Tensile Strength for Butt-fusion)	-	1800	-
8.7(Density)	-	700	-
8.5 (Oxidation Induction Time)	-	2200	-
8.4( Melt Flow Rate)	-	1100	-
8.2(Longitudinal Reversion Test)	-	1200	specimen preparation charges inclusive
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	1600	-
7.4.1.2(Ovality)	-	750	-
7.4 table -3 & 4(6.1 Dimensions)	-	0	included in 7.4.1.2
7.2(Length)	-	0	included in 7.4.1.2
6.2.1(6.1.1 Identification Stripes)	-	0	500
6.2(Colour)	-	500	-
6.1.4(PIPE DESCRIPTION)	-	0	-
6.1.3 (PIPE DESCRIPTION)	-	0	-
6, 6.1.2(PIPE DESCRIPTION)	-	0	-
6, 6.1.1(PIPE DESCRIPTION)	-	0	-
6, 6.1(PIPE DESCRIPTION)	-	0	-
8.6(Overall migration)	-	2200	specimen preparation charges inclusive
8.3(Carbon black)	-	925	-
5.4(Anti oxydent)	-	0	-
5.3(e)(Carbon Black Master Batch)	-	0	-
5.3(d)(Carbon Black Master Batch)	-	0	-
5.3(c)(Carbon Black Master Batch)	-	0	-
5.3(b)(Carbon Black Master Batch)	-	0	-
5.3 (a)(Carbon Black Master Batch)	-	0	-
5.2(Polyethylene Resin)	-	0	-
5, 5.1 table-1(MATERIALS)	-	0	-
7()	-	0	-
5.2(Density)	-	700	-
5.2(MFI @ 1900C/5.0 Kg)	-	1100	-
5.2(Volatile matter Content)	-	700	-
5.3(Toluene Extract)	-	0	-
Clause 7.1(Visual Apperance)	-	0	already added
Clause 7.3(Coiling)	-	0	-
Clause 8.3(Carbon Black content)	-	925	-
Clause 8.3(Carbon Black Dispersion)	-	700	-
Clause 8.6(Overall migration (stimulate))	-	2200	specimen preparation inclusive
Clause 8.6(Overall migration (surface of material))	-	0	-
7.1(Visual Appearance)	-	0	-
7.3(Coiling)	-	0	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	0	-
Cl. 8.3(Carbon Black Content)	-	0	-
Cl. 8.3(Carbon Black Dispersion)	-	0	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	-
8.7(Density-IS 7328:2020)	-	0	-
8.7(Corrected Density- IS 7328:2020)	-	0	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	0	already added
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	0	already added
Cl 8.3(Carbon Black Content)	-	0	-
Cl 8.3(Carbon Black Dispersion)	-	0	-

26 Aug, 2028

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

20575 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500	-
5.1.2(Film Form)	-	0	included in 5.1.1
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	-
5.1.6a(Carbon Black Content, Annex-A)	-	925	-
5.1.6b(Ash Content, Annex-A)	-	1200	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800	specimen preparation charges inclusive
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	conditioning charge
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	included with tensile strength cl 6.1
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	included with tensile strength cl 6.1
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	850	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1600	specimen preparation charges inclusive
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100	-
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	0	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
8.1, Table 3(Tear resistance , Annex B)	-	0	-
8.1, Table 3(Puncture resistance , Annex C)	-	0	-
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tear resistance , Annex B)	-	0	-
9.1, Table 4(Puncture resistance , Annex C)	-	0	-
Clause 9.1 (Table 4)(Break Elongation)	-	0	-
Clause 9.1 (Table 4)(Yield Elonation)	-	0	-
Clause 9.1 (Table 4)(Break strength)	-	0	-
Clause 9.1 (Table 4)(Yield strength)	-	0	-
Clause 8.1(Table 3)(Break Elongation)	-	0	-
Clause 8.1(Table 3)(Break strength)	-	0	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-
Clause 5.2.3(Tolerance on Width)	-	0	-
Cl.5.1.6(a)(Carbon Black Content)	-	0	-
Cl.5.1.6(b)(Ash content)	-	0	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0	-
5.2.1.1(Nominal Thickness)	-	0	-
5.2.1.2(Nominal width)	-	0	-
5.1.3(Odour)	-	0	-

26 Aug, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

POLYMER TESTING LABORATORY, CIPET:SARP-APDDRL

PLOT NO.- 7P, HI TECH DEFENCE & AEROSPACE PARK (IT SECTOR), Bangalore, Bengaluru Rural, Karnataka, 562149

9840376907 apddrl@cipet.gov.in

Scope List