BIS - LIMS (Laboratory Information Management System)

AA Electro Magnetic Laboratory Pvt Ltd, Gurugram

Plot174, udyog vihar, phase 4, Gurgaon, Gurugram, Haryana, 122015

8870082081 info@aaemtlabs.com

Scope List

Reset

28 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 13450 : Part 2 : Sec 25 (2018)

Medical Electrical Equipment Part 2 Particular Requirements for the Basic Safety and Essential Performance Section 25 Electrocardiographs

774500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(Power and Current)	-	10000	-
201.5(Temperature, Humidity, Dimensions, Force)	-	10000	-
201.7.4.101(Qualitative)	-	0	-
201.8(Current, Voltage, Energy, Dimensions, Impedance)	-	25000	-
201.8.5.5.1(Voltage, Time)	-	0	-
201.8.5.5.2(Energy)	-	0	-
201.9(Mechanical dimensions, strength , torque, force)	-	20000	-
201.11(Temperature)	-	15000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	35000	-
201.12.1.101.1(Automated measurements on ECGS)	-	0	-
201.12.1.101.2(Requirements for amplitude measurements)	-	0	-
201.12.1.101.3(Requirements for interval measurements)	-	0	-
201.12.1.101.3.2()	-	0	-
201.12.4(Protection against hazardous output)	-	25000	-
201.12.4.101(Indication of inoperable ELECTROCARDIOGRAPH)	-	0	-
201.12.4.102(ECG signals)	-	0	-
201.12.4.102.1(ECG signals)	-	0	-
201.12.4.102.2(Minimum required configuration)	-	0	-
201.12.4.102.3(ECG signals)	-	0	-
201.12.4.102.3.1(General)	-	0	-
201.12.4.102.3.2(Goldberger and Wilson LEADS)	-	0	-
201.12.4.102.4(Recovery time)	-	0	-
201.12.4.103(Input impedance)	-	0	-
201.12.4.104(Required GAINS)	-	0	-
201.12.4.105.2(Overload tolerance)	-	0	-
201.12.4.105.3(FILTERS (including line frequency interference FILTERS))	-	0	-
201.12.4.106.1(Noise level)	-	0	-
201.12.4.106.2(CHANNEL crosstalk)	-	0	-
201.12.4.107.1.1.1(High Frequency Response)	-	0	-
201.12.4.107.1.1.2(Low frequency (impulse) response)	-	0	-
201.12.4.107.1.2(Test with calibration ECG)	-	0	-
201.12.4.107.2(Linearity and Dynamic range)	-	0	-
201.12.4.107.3(Sampling and amplitude quantisation during data acquisition)	-	0	-
201.12.4.108(Printing, electronic storage and transmission)	-	0	-
201.12.4.108.1(Record identification)	-	0	-
201.12.4.108.2(PATIENT identification)	-	0	-
201.12.4.108.3.1(Time and event markers)	-	0	-
201.12.4.108.3.2(Recording speed)	-	0	-
201.12.4.108.3.3(Time and amplitude ruling)	-	0	-
201.12.4.109(Use with cardiac pacemakers)	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	25000	-
201.15(Mechanical strength, Temperature, current)	-	25000	-
15.3(Force, Dimensions, Temperature)	-	0	-
201.16(Leakage currents , dielectirc strength)	-	25000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	15000	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	15000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147000	-
202(Electromagnetic compatibility – Requirements and tests)	-	147500	-
201.12.1.101.3.1(* Requirements for absolute interval and wave duration measurements)	-	0	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	15000	-
201.16(ME SYSTEMS)	-	0	-
202.6.1(EMISSIONS)	-	25000	-
202.6.2.2(ELECTROSTATIC DISCHARGE (ESD))	-	25000	-
202.6.2.3(Radiated RF electromagnetic fields)	-	25000	-
202.6.2.4(Electrical fast transients and bursts)	-	25000	-
202.6.2.6(Conducted disturbances, induced by RF fields)	-	25000	-
202.6.2.101(Electrosurgery interference)	-	0	-
202(Electromagnetic compatibility – Requirements and tests)	-	147000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147500	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	20000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	20000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	5000	-
201.4(General requirements)	-	0	-
201.5(General requirements for testing of ME EQUIPMENT)	-	0	-
201.7(ME EQUIPMENT identification, marking and documents)	-	0	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	10000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	20000	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	20000	-
201.15(Construction of ME EQUIPMENT)	-	0	-

24 Sep, 2026

-
Included w.e.f 10.11.2025

IS 13450 : Part 2 : Sec 13 (2024)

Medical Electrical Equipment: Part 2 Particular Requirements for the Basic Safety and Essential Performance: Sec 13 Anaesthetic Workstation (First Revision)

295000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	147500		-
202(Electromagnetic disturbances — Requirements and tests)	-	147500		-

24 Sep, 2026

-
Included w.e.f 26.11.2025 Exclusion: only for 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS) and 202 (Electromagnetic compatibility – Requirements and tests)

IS 13450 : Part 2 : Sec 37 (2019)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 37 ultrasonic medical diagnostic and monitoring equipment

315000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	157500		-
202.6(ELECTROMAGNETIC COMPATIBILITY – Requirements and test)	-	157500		-

24 Sep, 2026

-
Included w.e.f 26.11.2025 Only for 201.17 (ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS) and 202.6 (ELECTROMAGNETIC COMPATIBILITY – Requirements and test)

IS 18112 (2025)

DIGITAL TELEVISION RECEIVER FOR SATELLITE BROADCAST TRANSMISSION SPECIFICATION (First Revision)

140000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.5(Safety Requirements)	-	60000		-
Clause 4.6(Electromagnetic Compatibility (EMC) Requirements)	-	80000		-

24 Sep, 2026

-
Included w.e.f 21.11.2025 Exclusion: Only for Cl 4.6 Electromagnetic Compatibility Requirements(EMC)

IS 13450 : Part 2 : Sec 54 (2024)

Medical electrical equipment Part 2 Particular requirements for basic safety and essential performance Section 54 X-ray equipment for radiography and radioscopy First revision

295000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147500		-
Cl-202(Electromagnetic disturbances – Requirements and tests)	-	147500		-

24 Sep, 2026

-
Included w.e.f 07.11.2025 only for 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS) and 202 (Electromagnetic compatibility – Requirements and tests)

IS 13450 : Part 2 : Sec 12 (2023)

Medical Electrical Equipment Part 2 Particular requirements for basic safety and essential performance Section 12 Critical care ventilators (First Revision)

295000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	147500		-
202(Electromagnetic disturbances — Requirements and tests)	-	147500		-

24 Sep, 2026

-
Included w.e.f 07.11.2025 only for 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS) and 202 (Electromagnetic compatibility – Requirements and tests)

IS 13450 : Part 2 : Sec 16 (2019)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 16 haemodialysis, haemodiafiltration and haemofiltration equipment

315000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	157000	-
202(Electromagnetic disturbances – Requirements and tests)	-	157000	-
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	157000	-
202(Electromagnetic disturbances – Requirements and tests)	-	157000	-

24 Sep, 2026

-
Included w.e.f 07.11.2025 only for 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS) and 202 (Electromagnetic compatibility – Requirements and tests)

IS 13450 : PART 2 : SEC 24 (2019)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 24 infusion pumps and controllers (First Revision)

295000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147500	-
202(Electromagnetic compatibility – Requirements and tests)	-	147500	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147500	-
202(Electromagnetic compatibility – Requirements and tests)	-	147500	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	147500	-
202(Electromagnetic compatibility – Requirements and tests)	-	147500	-

24 Sep, 2026

-
Included w.e.f 06-11-2025, only for 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS) and 202 (Electromagnetic compatibility – Requirements and tests)

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Inputting of text)	-	7000	-
5.2(Message Readability)	-	7000	-
6(Marking)	-	1000	-
"Cl.6.1 "(Marking)	-	0	-
"Cl.6.2 "(BIS Certification Marking)	-	0	-
4(Requirements)	-	1000	-
5(Tests)	-	0	-
6(Marking)	-	0	-
5.1(Inputting of text)	-	0	-
5.2(Message Readability)	-	0	-
6(Marking)	-	0	-
"Cl.6.1 "(Marking)	-	0	-
"Cl.6.2 "(BIS Certification Marking)	-	0	-
4(Requirements)	-	0	-
5(Tests)	-	0	-
6(Marking)	-	0	-

24 Sep, 2026

-
Included w.e.f. 18.08.2025

IS 18112 (2022)

Digital Television Receiver for Satellite Broadcast Transmission Specification

140000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.5(Safety specification)	-	60000		-
3.6(Electromagnetic Compatibility (EMC) Requirements)	-	80000		-

24 Sep, 2026

-
Included w.e.f 10.09.2025 Exclusion: Restricted to only Cl.3.5(Safety specification)n & Cl.3.6 ((Electromagnetic Compatibility (EMC) Requirements)

IS 13450 : Part 2 : Sec 21 (2023)

Medical Electrical Equipment Part 2 Particular Requirements for the Basic Safety and Essential Performance Section 21 Infant Radiant Warmer First Revision

1400000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	32000	-
201.5(General requirements for testing ME EQUIPMENT)	-	40000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	33000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	15000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	100000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	45000	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	32000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	45000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	17000	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	20000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	22000	-
201.15(Construction of ME EQUIPMENT)	-	24000	-
201.16(ME SYSTEMS)	-	30000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	450000	-
202(Electromagnetic disturbances – Requirements and tests)	-	495000	-
201.4(General requirements)	-	0	-
201.5(General requirements for testing ME EQUIPMENT)	-	0	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.7(ME EQUIPMENT identification, marking and documents)	-	0	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	0	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	0	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	0	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	0	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	0	-
201.15(Construction of ME EQUIPMENT)	-	0	-
201.16(ME SYSTEMS)	-	0	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	0	-
202(Electromagnetic disturbances – Requirements and tests)	-	0	-

24 Sep, 2026

-
Included w.e.f.10.09.2025

IS/IEC 62368 : Part 1 (2023)

Audio Video Information and Communication Technology Equipment - Part 1: Safety Requirements (Second Revision)

192300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General- materials, components)	-	1500	-
Cl-4.2(Energy source classifications)	-	500	-
Cl-4.3(Protection against energy sources)	-	500	-
Cl-4.4(Safeguards)	-	500	-
Cl-4.5(Explosion)	-	500	-
Cl-4.6(Fixing of conductors and conductive parts)	-	800	-
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	600	-
Cl-4.8(Equipment containing coin or button cell batteries)	-	2500	-
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	500	-
Cl-4.10(Components requirements)	-	600	-
Cl-5.1(General- Electrically-caused injury)	-	600	-
Cl-5.2(Classification and limits of electrical energy sources)	-	2000	-
Cl-5.3(Protection against electrical energy sources)	-	2000	-
Cl-5.4(Insulation materials and requirements)	-	6000	-
Cl-5.5(Components as safeguards)	-	2500	-
Cl-5.6(Protective conductor)	-	2500	-
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	2500	-
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	1000	-
Cl-6.1(General- Electrically-caused fire)	-	600	-
Cl-6.2(Classification of power sources and potential ignition sources)	-	2500	-
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	2500	-
Cl-6.4(Safeguards against fire under single fault conditions)	-	2500	-
Cl-6.5(Internal and external wiring)	-	2500	-
Cl-7.1(General- Injury caused by hazardous substances)	-	400	-
Cl-7.2(Reduction of exposure to hazardous substances)	-	2500	-
Cl-7.3(Ozone exposure)	-	500	-
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	400	-
Cl-7.5(Use of instructional safeguards and instructions)	-	400	-
Cl-8.1(General- Mechanically-caused injury)	-	400	-
Cl-8.2(Mechanical energy source classifications)	-	400	-
Cl-8.3(Safeguards against mechanical energy sources)	-	500	-
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	2500	-
Cl-8.5(Safeguards against moving parts)	-	2500	-
Cl-8.6(Stability of equipment)	-	2000	-
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	2000	-
Cl-8.8(Handle strength)	-	1500	-
Cl-8.9(Wheels or casters attachment requirements)	-	1000	-
Cl-8.10(Carts, stands, and similar carriers)	-	1000	-
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	1500	-
Cl-9.1(General-Thermal burn injury)	-	500	-
Cl-9.2(Thermal energy source classifications)	-	2500	-
Cl-9.3(Touch temperature limits)	-	4500	-
Cl-9.4(Safeguards against thermal energy sources)	-	600	-
Cl-9.5(Requirements for safeguards)	-	500	-
Cl-9.6(Requirements for wireless power transmitters)	-	0	-
Cl-10.1(General-Radiation)	-	0	-
Cl-10.2(Radiation energy source classifications)	-	0	-
Cl-10.3(Safeguards against laser radiation)	-	0	-
Cl-10.4("Safeguards against optical radiation from lamps and lamp systems (including LED types)")	-	0	-
Cl-10.6(Safeguards against acoustic energy sources)	-	0	-
Annex A(Examples of equipment within the scope of this document)	-	0	-
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	400	-
Annex B-2(Normal operating conditions)	-	5000	-
Annex B-3(Simulated abnormal operating conditions)	-	6000	-
Annex B-4(Simulated single fault conditions)	-	4000	-
Annex C-1(Protection of materials in equipment from UV radiation)	-	400	-
Annex C-2(UV light conditioning test)	-	5000	-
Annex D-1(Impulse test generators)	-	1500	-
Annex D-2(Antenna interface test generator)	-	0	-
Annex D-3(Electronic pulse generator)	-	0	-
Annex E-1(Electrical energy source classification for audio signals)	-	2500	-
Annex E-2(Audio signals used during test)	-	2500	-
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	2500	-
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	500	-
Annex F-2(Letter symbols and graphical symbols)	-	500	-
Annex F-3(Equipment markings)	-	500	-
Annex F-4(Instructions)	-	500	-
Annex F-5(Instructional safeguards)	-	500	-
Annex G-1(Switches)	-	15000	-
Annex G-2(Relays)	-	3000	-
Annex G-3(Protective devices)	-	2000	-
Annex G-4(Connectors)	-	2000	-
Annex G-5(Wound components)	-	2000	-
Annex G-6(Wire insulation)	-	2000	-
Annex G-7(Mains power supply cords and interconnection cables)	-	2000	-
Annex G-8(Varistors)	-	2000	-
Annex G-9(Integrated circuit (IC) current limiters)	-	2000	-
Annex G-10(Resistors)	-	2000	-
Annex G-11(Capacitors and RC units)	-	2000	-
Annex G-12(Optocouplers)	-	2000	-
Annex G-13(Printed boards)	-	2000	-
Annex G-14(Coatings on component terminals)	-	2000	-
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	2000	-
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	2000	-
Annex H-1(General- Criteria for telephone ringing signals)	-	500	-
Annex H-2(Method A)	-	1500	-
Annex H-3(Method B)	-	500	-
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	500	-
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	0	-
Annex J-2(Type tests)	-	0	-
Annex J-3(Testing during manufacturing)	-	0	-
Annex K-1(General- Safety interlocks)	-	0	-
Annex K-2(Components of the safety interlock safeguard mechanism)	-	0	-
Annex K-3(Inadvertent change of operating mode)	-	0	-
Annex K-4(Interlock safeguard override)	-	0	-
Annex K-5(Fail-safe)	-	0	-
Annex K-6(Mechanically operated safety interlocks)	-	0	-
Annex K-7(Interlock circuit isolation)	-	0	-
Annex L-1(General requirements)	-	500	-
Annex L-2(Permanently connected equipment)	-	500	-
Annex L-3()	-	500	-
Annex L-4(Single-phase equipment)	-	500	-
Annex L-5(Three-phase equipment)	-	500	-
Annex L-6(Switches as disconnect devices)	-	500	-
Annex L-7(Plugs as disconnect devices)	-	500	-
Annex L-8(Multiple power sources)	-	500	-
Annex L-9(Compliance criteria)	-	500	-
Annex M-1(General requirements)	-	1000	-
Annex M-2(Safety of batteries and their cells)	-	1000	-
Annex M-3(Protection circuits for batteries provided within the equipment)	-	5000	-
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	5000	-
Annex M-5(Risk of burn due to short-circuit during carrying)	-	1000	-
Annex M-6(Safeguards against short-circuits)	-	200	-
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	200	-
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	500	-
Annex M-9(Preventing electrolyte spillage)	-	500	-
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	500	-
Annex N(Electrochemical potentials (V))	-	0	-
Annex O(Measurement of creepage distances and clearances)	-	2000	-
Annex P-1(General-Safeguards against conductive objects)	-	0	-
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	2500	-
Annex P-3(Safeguards against spillage of internal liquids)	-	2500	-
Annex P-4(Metallized coatings and adhesives securing parts)	-	500	-
Annex Q-1(Limited power source)	-	2000	-
Annex Q-2(Test for external circuits – paired conductor cable)	-	500	-
Annex R(Limited short-circuit test)	-	500	-
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	0	-
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	500	-
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	500	-
Annex S-4(Flammability classification of materials)	-	500	-
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	500	-
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	0	-
Annex T-1(General-Mechanical strength tests)	-	0	-
Annex T-2(Steady force test, 10 N)	-	200	-
Annex T-3(Steady force test, 30 N)	-	200	-
Annex T-4(Steady force test, 100 N)	-	200	-
Annex T-5(Steady force test, 250 N)	-	200	-
Annex T-6(Enclosure impact test)	-	500	-
Annex T-7(Drop test)	-	500	-
Annex T-8(Stress relief test)	-	500	-
Annex T-9(Glass impact test)	-	500	-
Annex T-10(Glass fragmentation test)	-	0	-
Annex T-11(Test for telescoping or rod antennas)	-	0	-
Annex V-1(Accessible parts of equipment)	-	0	-
Annex V-2(Accessible part criterion)	-	0	-
Annex W(Comparison of terms introduced in this document)	-	0	-
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	0	-
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	0	-
Annex Y-2(Resistance to UV radiation)	-	500	-
Annex Y-3(Resistance to corrosion)	-	500	-
Annex Y-4(Gaskets)	-	500	-
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	500	-
Annex Y-6(Mechanical strength of enclosures)	-	0	-
Cl-10.5(Safeguards against X-radiation)	-	500	-
Annex U("Mechanical strength of CRTs and protection against the effects of implosion")	-	0	-

24 Sep, 2026

-
Included w.e..f 28.07.2025

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

172000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	5000	-
8(Protection against accidental contact with live parts)	-	15000	-
9(Terminals)	-	10000	-
10(PROVISION FOR EARTHING)	-	5000	-
11(MOISTURE RESISTANCE)	-	15000	-
12(Electric Strength)	-	10000	-
13(Thermal endurance test for winding of ballasts)	-	0	-
14(Fault conditions)	-	30000	-
15(Transformer heating)	-	30000	-
16(Construction)	-	0	-
17(Creepage distance and clearances)	-	6000	-
18(Screws, current carrying parts and connections)	-	6000	-
19(Resistance to heat, fire and tracking)	-	20000	-
20(Resistance to corrosion)	-	20000	-
16(Enclosures)	-	0	-
16(Bridging resistor in primary circuit)	-	0	-
16(Capacitor and RC units)	-	0	-
16(RF suppression (X-Y capacitors))	-	0	-
16(Inductor)	-	0	-
16(MOV/VDR)	-	0	-
16(SMPS/Mains Transformer)	-	0	-
16(PCB material)	-	0	-
19(Metal base PCB for LED)	-	0	-
19(Transparent cover)	-	0	-
19(Bobbin)	-	0	-
16(Insulated tape)	-	0	-
16(Heat shrinkage sleeve)	-	0	-
19(Terminals)	-	0	-
16(Connector)	-	0	-
16(Fuse)	-	0	-
16(Internal wire)	-	0	-
16(LED)	-	0	-
16(Opto-coupler)	-	0	-
16(Opto-coupler)	-	0	-
16(EMI/EMC filter)	-	0	-
16(Winding wire)	-	0	-
16(Thin sheet materials)	-	0	-
7(Marking)	-	0	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	0	-
9(TERMINALS)	-	0	-
10(PROVISIONS FOR PROTECTIVE EARTHING)	-	0	-
11(MOISTURE RESISTANCE AND INSULATION)	-	0	-
12(ELECTRIC STRENGTH)	-	0	-
14(FAULT CONDITIONS)	-	0	-
15(TRANSFORMER HEATING)	-	0	-
16(CONSTRUCTION)	-	0	-
17(CREEPAGE DISTANCES AND CLEARANCES)	-	0	-
18("SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS")	-	0	-
19(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	0	-
20(RESISTANCE TO CORROSION)	-	0	-
4(GENERAL REQUIREMENTS)	-	0	-
5(GENERAL NOTES ON TESTS)	-	0	-
6(CLASSIFICATION)	-	0	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 17017 : Part 1 (2018)

Electric Vehicle Conductive Charging System Part 1 General Requirements

790000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENTS)	-	25000	-
5(CLASSIFICATION)	-	25000	-
6(CHARGING MODES AND FUNCTIONS)	-	25000	-
7(COMMUNICATIONS)	-	25000	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	100000	-
9(CONDUCTIVE ELECTRICAL INTERFACE REQUIREMENTS)	-	200000	-
10(REQUIREMENTS FOR ADAPTORS)	-	10000	-
11(CABLE ASSEMBLY REQUIREMENTS)	-	150000	-
12(EV SUPPLY EQUIPMENT CONSTRUCTIONAL REQUIREMENTS AND TESTS)	-	100000	-
13(OVERLOAD AND SHORT-CIRCUIT PROTECTION)	-	100000	-
14(AUTOMATIC RECLOSING OF PROTECTIVE DVICES)	-	10000	-
15(EMERGENCY SWITCHING OR DISCONNECT ( OPTIONAL))	-	10000	-
16(MARKING AND INSTRUCTIONS)	-	10000	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS/IEC 80601 : Part 2 : Sec 49 (2018)

Medical electrical equipment Part 2- Particular requirements for basic safety and essential performance- Sec 49 Multifunction patient monitors

1340000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.5(General requirements for testing of ME EQUIPMENT)	-	25000	-
201.6(Classification Of ME equipment and ME systems)	-	25000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	20000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	35000	-
201.9(Protection against MECAHNICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	35000	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	35000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	30000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	30000	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	30000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	35000	-
201.15(Construction of ME EQUIPMENT)	-	30000	-
201.16(ME SYSTEMS)	-	25000	-
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	450000	-
202(Electromagnetic disturbances-Requirements and tests)	-	495000	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	10000	-
201.4(General requirements)	-	30000	-
201.5(General requirements for testing of ME EQUIPMENT)	-	0	-
201.6(Classification Of ME equipment and ME systems)	-	0	-
201.7(ME EQUIPMENT identification, marking and documents)	-	0	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	0	-
201.9(Protection against MECAHNICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	0	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	0	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	0	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	0	-
201.15(Construction of ME EQUIPMENT)	-	0	-
201.16(ME SYSTEMS)	-	0	-
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	0	-
202(Electromagnetic disturbances-Requirements and tests)	-	0	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	0	-
201.4(General requirements)	-	0	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 13450 : Part 2 : Sec 20 (2023)

Medical Electrical Equipment Part 2 Particular Requirements for the Basic Safety and Essential Performance Section 20 Infant Transport Incubators First Revision

1310000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	30000	-
201.5(General requirements for testing ME EQUIPMENT)	-	30000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	15000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	15000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	45000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	20000	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	25000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	30000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	30000	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	30000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	30000	-
201.15(Construction of ME EQUIPMENT)	-	20000	-
201.16(ME SYSTEMS)	-	20000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	450000	-
202(Electromagnetic disturbances – Requirements and tests)	-	495000	-
212(* Requirements for MEDICAL ELECTRICAL EQUIPMENT and MEDICAL ELECTRICAL SYSTEMS intended for use in the EMERGENCY MEDICAL SERVICES ENVIRONMENT)	-	25000	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 13450 : Part 2 : Sec 40 (2020)

Medical Electrical Equipment Part 2 Particular Requirements for the Basic Safety and Essential Performance Section 40 Electromyographs and evoked response equipment

1360000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	30000	-
201.5(General requirements for testing of ME EQUIPMENT)	-	35000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	25000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	25000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	45000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	45000	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	45000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	35000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	35000	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	35000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	45000	-
201.15(Construction of ME EQUIPMENT)	-	35000	-
201.16(ME SYSTEMS)	-	25000	-
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	450000	-
202(ELECTROMAGNETIC DISTURBANCES – Requirements and tests)	-	450000	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 13450 : Part 2 : Sec 2 (2024)

Medical electrical equipment Part 2 Particular requirements for basic safety and essential performance Section 2 High frequency surgical equipment and high frequency surgical accessories First revision

1447000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	32000	-
201.5(General requirements for testing of ME EQUIPMENT)	-	40000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	35000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	15000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	100000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	50000	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	35000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	50000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	20000	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	20000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	25000	-
201.15(Construction of ME EQUIPMENT)	-	25000	-
201.16(ME SYSTEMS)	-	30000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	450000	-
202(ELECTROMAGNETIC DISTURBANCES – Requirements and tests)	-	495000	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	15000	-
Annex BB(ELECTROMAGNETIC DISTURBANCES created by HF SURGICAL EQUIPMENT)	-	10000	-
201.4(General requirements)	-	0	-
201.5(General requirements for testing of ME EQUIPMENT)	-	0	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.7(ME EQUIPMENT identification, marking and documents)	-	0	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	0	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.10(Protection against unwanted and excessive radiation HAZARDS)	-	0	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	0	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	0	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	0	-
201.15(Construction of ME EQUIPMENT)	-	0	-
201.16(ME SYSTEMS)	-	0	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	0	-
202(ELECTROMAGNETIC DISTURBANCES – Requirements and tests)	-	0	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	0	-
Annex BB(ELECTROMAGNETIC DISTURBANCES created by HF SURGICAL EQUIPMENT)	-	0	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 13450 : Part 2 : Sec 26 (2021)

Medical electrical equipment Part 2 Particular requirements for basic safety and essential performance Section 26 Electroencephalographs

1450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	30000	-
201.5(General requirements for testing ME EQUIPMENT)	-	40000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	40000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	20000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	100000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	50000	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	50000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	50000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	20000	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	25000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	25000	-
201.15(Construction of ME EQUIPMENT)	-	25000	-
201.16(ME SYSTEMS)	-	30000	-
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	450000	-
202(Electromagnetic disturbances – Requirements and tests)	-	495000	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 13450 : Part 2 : Sec 27 (2018)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 27 electrocardiographic monitoring equipment

1212000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
201.4(General requirements)	-	30000	-
201.5(General requirements for testing of ME EQUIPMENT)	-	30000	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	12000	-
201.7(ME EQUIPMENT identification, marking and documents)	-	15000	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	50000	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	30000	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	30000	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	40000	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	40000	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	40000	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS)	-	50000	-
201.15(Construction of ME EQUIPMENT)	-	35000	-
201.16(Me Systems)	-	20000	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	370000	-
202(Electromagnetic compatibility – Requirements and tests)	-	170000	-
202.6(ELECTROMAGNETIC COMPATIBILITY)	-	150000	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	100000	-
201.4(General requirements)	-	0	-
201.5(General requirements for testing of ME EQUIPMENT)	-	0	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.7(ME EQUIPMENT identification, marking and documents)	-	0	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	0	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	0	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	0	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	0	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	0	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	0	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS)	-	0	-
201.15(Construction of ME EQUIPMENT)	-	0	-
201.16(Me Systems)	-	0	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	0	-
202(Electromagnetic compatibility – Requirements and tests)	-	0	-
202.6(ELECTROMAGNETIC COMPATIBILITY)	-	0	-
208(General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems)	-	0	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 16046 : Part 1 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 1 Nickel Systems ( Second Revision )

255000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	0	-
5(General Safety Considerations)	-	0	-
5.1(General)	-	0	-
5.2(Insulation and Wiring)	-	5000	-
5.3(Venting)	-	0	-
5.4(Temperature, Voltage and Current Management)	-	0	-
5.5(Terminal Contacts)	-	0	-
5.6(Assembly of Cells into batteries)	-	0	-
5.7(Quality Plan)	-	0	-
6(Tyoe Test amd Sample Size)	-	0	-
7(Specific requirements and tests)	-	0	-
7.1(Charging procedure for test purposes)	-	20000	-
7.2(Intended Use)	-	100000	-
7.3(Reasonably foreseeable misuse)	-	100000	-
8(Information for safety)	-	0	-
8.1(General)	-	0	-
8.2(Small Cell and battery safety information)	-	25000	-
9(Marking)	-	0	-
9.1(Cell Marking)	-	0	-
9.2(Battery Marking)	-	0	-
9.3(Caution for ingestion of small cells and batteries)	-	5000	-
9.4(Other information)	-	0	-
10(Packaging)	-	0	-
4(Parameter Measurement Tolerances)	-	0	-
5(General Safety Considerations)	-	0	-
5.1(General)	-	0	-
5.2(Insulation and Wiring)	-	0	-
5.3(Venting)	-	0	-
5.4(Temperature, Voltage and Current Management)	-	0	-
5.5(Terminal Contacts)	-	0	-
5.6(Assembly of Cells into batteries)	-	0	-
5.7(Quality Plan)	-	0	-
6(Tyoe Test amd Sample Size)	-	0	-
7(Specific requirements and tests)	-	0	-
7.1(Charging procedure for test purposes)	-	0	-
7.2(Intended Use)	-	0	-
7.3(Reasonably foreseeable misuse)	-	0	-
8(Information for safety)	-	0	-
8.1(General)	-	0	-
8.2(Small Cell and battery safety information)	-	0	-
9(Marking)	-	0	-
9.1(Cell Marking)	-	0	-
9.2(Battery Marking)	-	0	-
9.3(Caution for ingestion of small cells and batteries)	-	0	-
9.4(Other information)	-	0	-
10(Packaging)	-	0	-

24 Sep, 2026

-
Included w.e.f. 28.07.2025

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

135000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	1000	-
8.1.1(Protection against live parts in all positions)	-	1000	-
8.1.2(Protection against live parts in openings)	-	1000	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	1000	-
8.1.4(Protection against live parts against protective impedance)	-	1000	-
9(Starting of motor operation test requirements and tests)	-	6000	-
10.1(Power input)	-	6000	-
10.2(Current input)	-	0	-
11.1(General)	-	0	-
11.2(General)	-	0	-
11.3(Heating)	-	0	-
13.1(General)	-	0	-
13.2(Leakage current at operating temperature)	-	6000	-
13.3(Electric Strength at operating temperature)	-	6000	-
14(Transient Over Voltages)	-	8000	-
15.0(General)	-	0	-
15.2(Spillage Test)	-	7500	-
15.3(Humidity Test)	-	7500	-
16.0(General)	-	0	-
16.1(General)	-	0	-
16.2(Leakage Current (after Clause 15))	-	6000	-
16.3(Electric Strength (after clause 15 and 16.2))	-	6000	-
17(Over Load Protection of Transformers and associated circuits)	-	9000	-
18(Endurance Test requirements and tests)	-	14000	-
19(Abnormal Operation)	-	10000	-
20(Stability test)	-	2000	-
21(Mechanical Strength Test)	-	3000	-
22(Construction verification related test)	-	12500	-
23(General)	-	2000	-
24(Components)	-	2000	-
25(Supply connection and external flexible cords)	-	0	-
26(Terminals for external conductors)	-	3000	-
27(Provision for earthing)	-	3000	-
28(Screw test and connections)	-	2000	-
29(clearance, creepage distances and solid insulation)	-	2000	-
30.1(Ball pressure test)	-	2000	-
30.2(Glow Wire Test)	-	2000	-
31(Resistance to Rusting)	-	0	-
32(Radiation Toxicity and Similar Hazards)	-	0	-
4(General requirement)	-	0	-
16(Leakage current and electric strength)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
8.1.5(Live parts of built-in appliances)	-	1000	-
11.4(Heating appliances)	-	0	-
11.5(Motor-operated appliances)	-	0	-
11.6(Combined appliances)	-	0	-
11.7(Duration corresponding)	-	0	-
11.8(Temperature rise)	-	1500	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
4(General Requirement)	-	0	-
5(General conditions for tests)	-	0	-
6(Classification- IS 302-1)	-	0	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	-
30.2(Needle Flame Test)	-	0	-
7(Marking and instructions)	-	0	-
8.1.1(Protection against live parts in all positions)	-	0	-
8.1.2(Protection against live parts in openings)	-	0	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	-
8.1.4(Protection against live parts against protective impedance)	-	0	-
9(Starting of motor operation test requirements and tests)	-	0	-
10.1(Power input)	-	0	-
10.2(Current input)	-	0	-
11.1(General)	-	0	-
11.2(General)	-	0	-
11.3(Heating)	-	0	-
13.1(General)	-	0	-
13.2(Leakage current at operating temperature)	-	0	-
13.3(Electric Strength at operating temperature)	-	0	-
14(Transient Over Voltages)	-	0	-
15.0(General)	-	0	-
15.2(Spillage Test)	-	0	-
15.3(Humidity Test)	-	0	-
16.0(General)	-	0	-
16.1(General)	-	0	-
16.2(Leakage Current (after Clause 15))	-	0	-
16.3(Electric Strength (after clause 15 and 16.2))	-	0	-
17(Over Load Protection of Transformers and associated circuits)	-	0	-
18(Endurance Test requirements and tests)	-	0	-
19(Abnormal Operation)	-	0	-
20(Stability test)	-	0	-
21(Mechanical Strength Test)	-	0	-
22(Construction verification related test)	-	0	-
23(General)	-	0	-
25(Supply connection and external flexible cords)	-	0	-
26(Terminals for external conductors)	-	0	-
27(Provision for earthing)	-	0	-
28(Screw test and connections)	-	0	-
29(clearance, creepage distances and solid insulation)	-	0	-
30.1(Ball pressure test)	-	0	-
30.2(Glow Wire Test)	-	0	-
31(Resistance to Rusting)	-	0	-
32(Radiation Toxicity and Similar Hazards)	-	0	-
4(General requirement)	-	0	-
16(Leakage current and electric strength)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
8.1.5(Live parts of built-in appliances)	-	0	-
11.4(Heating appliances)	-	0	-
11.5(Motor-operated appliances)	-	0	-
11.6(Combined appliances)	-	0	-
11.7(Duration corresponding)	-	0	-
11.8(Temperature rise)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
4(General Requirement)	-	0	-
5(General conditions for tests)	-	0	-
6(Classification- IS 302-1)	-	0	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	-
30.2(Needle Flame Test)	-	0	-
7(Marking and instructions)	-	0	-
8.1.1(Protection against live parts in all positions)	-	0	-
8.1.2(Protection against live parts in openings)	-	0	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	0	-
8.1.4(Protection against live parts against protective impedance)	-	0	-
9(Starting of motor operation test requirements and tests)	-	0	-
10.1(Power input)	-	0	-
10.2(Current input)	-	0	-
11.1(General)	-	0	-
11.2(General)	-	0	-
11.3(Heating)	-	0	-
13.1(General)	-	0	-
13.2(Leakage current at operating temperature)	-	0	-
13.3(Electric Strength at operating temperature)	-	0	-
14(Transient Over Voltages)	-	0	-
15.0(General)	-	0	-
15.2(Spillage Test)	-	0	-
15.3(Humidity Test)	-	0	-
16.0(General)	-	0	-
16.1(General)	-	0	-
16.2(Leakage Current (after Clause 15))	-	0	-
16.3(Electric Strength (after clause 15 and 16.2))	-	0	-
17(Over Load Protection of Transformers and associated circuits)	-	0	-
18(Endurance Test requirements and tests)	-	0	-
19(Abnormal Operation)	-	0	-
20(Stability test)	-	0	-
21(Mechanical Strength Test)	-	0	-
22(Construction verification related test)	-	0	-
23(General)	-	0	-
25(Supply connection and external flexible cords)	-	0	-
26(Terminals for external conductors)	-	0	-
27(Provision for earthing)	-	0	-
28(Screw test and connections)	-	0	-
29(clearance, creepage distances and solid insulation)	-	0	-
30.1(Ball pressure test)	-	0	-
30.2(Glow Wire Test)	-	0	-
31(Resistance to Rusting)	-	0	-
32(Radiation Toxicity and Similar Hazards)	-	0	-
4(General requirement)	-	0	-
16(Leakage current and electric strength)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
18(Endurance)	-	0	-
8.1.5(Live parts of built-in appliances)	-	0	-
11.4(Heating appliances)	-	0	-
11.5(Motor-operated appliances)	-	0	-
11.6(Combined appliances)	-	0	-
11.7(Duration corresponding)	-	0	-
11.8(Temperature rise)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
4(General Requirement)	-	0	-
5(General conditions for tests)	-	0	-
6(Classification- IS 302-1)	-	0	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	0	-
30.2(Needle Flame Test)	-	0	-

24 Sep, 2026

-
Included w.e.f. 21.08.2025 Exclusion "22 (Construction verification related test) 24 (Components)"

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

43500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	1000	-
6(Interchangeability)	-	5000	-
7(Protection against accidental contact with live parts)	-	3000	-
8(Insulation Resistance and Electric Strength)	-	7000	-
9(MECHANICAL STRENGTH)	-	2000	-
10(cap temperature)	-	5000	-
11(Resistance to Heat)	-	4000	-
12(Resistance to Flame and Ignition)	-	4000	-
13(Fault conditions)	-	7000	-
14(Creepage distance and clearances)	-	5500	-
4(General requirement and General test requirements)	-	0	-
5(Marking)	-	0	-
6(Interchangeability)	-	0	-
7(Protection against accidental contact with live parts)	-	0	-
8(Strength after humidity treatment)	-	0	-
9(Mechanical strength)	-	0	-
10(Cap temperature rise)	-	0	-
11(Resistance to heat)	-	0	-
12(Resistance to flame and ignition)	-	0	-
13(Fault conditions)	-	0	-
14(Creepage distances and clearances)	-	0	-
15(Selection of lamps for tests (Sampling))	-	0	-
16(Condition of compliance)	-	0	-
17(Tests)	-	0	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	0	-
Annex B(Lamps with operating position limitations)	-	0	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	0	-
5(Marking)	-	0	-
6(Interchangeability)	-	0	-
7(Protection against accidental contact with live parts)	-	0	-
8(Insulation Resistance and Electric Strength)	-	0	-
9(MECHANICAL STRENGTH)	-	0	-
10(cap temperature)	-	0	-
11(Resistance to Heat)	-	0	-
12(Resistance to Flame and Ignition)	-	0	-
13(Fault conditions)	-	0	-
14(Creepage distance and clearances)	-	0	-
4(General requirement and General test requirements)	-	0	-
5(Marking)	-	0	-
6(Interchangeability)	-	0	-
7(Protection against accidental contact with live parts)	-	0	-
8(Strength after humidity treatment)	-	0	-
9(Mechanical strength)	-	0	-
10(Cap temperature rise)	-	0	-
11(Resistance to heat)	-	0	-
12(Resistance to flame and ignition)	-	0	-
13(Fault conditions)	-	0	-
14(Creepage distances and clearances)	-	0	-
15(Selection of lamps for tests (Sampling))	-	0	-
16(Condition of compliance)	-	0	-
17(Tests)	-	0	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	0	-
Annex B(Lamps with operating position limitations)	-	0	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	0	-
5(Marking)	-	0	-
6(Interchangeability)	-	0	-
7(Protection against accidental contact with live parts)	-	0	-
8(Insulation Resistance and Electric Strength)	-	0	-
9(MECHANICAL STRENGTH)	-	0	-
10(cap temperature)	-	0	-
11(Resistance to Heat)	-	0	-
12(Resistance to Flame and Ignition)	-	0	-
13(Fault conditions)	-	0	-
14(Creepage distance and clearances)	-	0	-
4(General requirement and General test requirements)	-	0	-
5(Marking)	-	0	-
6(Interchangeability)	-	0	-
7(Protection against accidental contact with live parts)	-	0	-
8(Strength after humidity treatment)	-	0	-
9(Mechanical strength)	-	0	-
10(Cap temperature rise)	-	0	-
11(Resistance to heat)	-	0	-
12(Resistance to flame and ignition)	-	0	-
13(Fault conditions)	-	0	-
14(Creepage distances and clearances)	-	0	-
15(Selection of lamps for tests (Sampling))	-	0	-
16(Condition of compliance)	-	0	-
17(Tests)	-	0	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	0	-
Annex B(Lamps with operating position limitations)	-	0	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	0	-

24 Sep, 2026

-
Included w.e.f.21.08.2025 Exclusion 6 (Interchangeability)

IS 16046 : Part 2 (2018)

270000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	0	-
5(General Safety Considerations)	-	0	-
5.1(General)	-	0	-
5.2(Insulation and Wiring)	-	2500	-
5.3(Venting)	-	0	-
5.4(Temperature, Voltage and Current Management)	-	0	-
5.5(Terminal Contacts)	-	0	-
5.6(Assembly of Cells into batteries)	-	0	-
5.7(Quality Plan)	-	0	-
5.8(Battery Safety Components)	-	0	-
6(Type Test and Sample Size)	-	0	-
7(Specific requirements and tests)	-	0	-
7.1(Charging procedure for test purposes)	-	25000	-
7.2(Intended Use)	-	110000	-
7.3(Reasonably foreseeable misuse)	-	100000	-
8(Information for safety)	-	0	-
8.1(General)	-	0	-
8.2(Small Cell and battery safety information)	-	25000	-
9(Marking)	-	0	-
9.1(Cell Marking)	-	0	-
9.2(Battery Marking)	-	0	-
9.3(Caution for ingestion of small cells and batteries)	-	7500	-
9.4(Other information)	-	0	-
10(Packaging)	-	0	-

24 Sep, 2026

-
Included w.e.f.03.07.2025

IS 16242 : Part 1 (2014)

Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.6(Power interface)	-	5000	-
4.7(Marking & instructions)	-	2000	-
5.1(Protection against shock and energy hazards)	-	5000	-
5.2(Requirement of auxiliary circuits)	-	5000	-
5.3(Protective earthing and bonding)	-	3000	-
5.4(AC and DC power isolation)	-	2000	-
5.5(Over current and earth fault condition)	-	3000	-
5.6(Safety interlocks)	-	5000	-
5.7(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	5000	-
6.1(Wiring, connections and supply)	-	3000	-
6.2(Connection to power)	-	3000	-
6.3(Wiring terminals for external power conductors)	-	3000	-
7.1(Enclosure)	-	2000	-
7.2(STABILITY)	-	3000	-
7.3(MECHANICAL STRENGTH)	-	5000	-
7.4(Construction details)	-	5000	-
7.5(Resistance to fire)	-	3000	-
7.6(Battery location)	-	5000	-
7.7(Temperature rise)	-	4000	-
8.1(General procision for earth leakage)	-	3000	-
8.2(Electric Strength)	-	3000	-
8.3(Abnormal operating and fault conditions)	-	5000	-
9.0(Connection to telecommunication networks)	-	3000	-

24 Sep, 2026

-
-

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

75000 View breakup
For Electronic games (video), Wireless headphone and earphone, Electronic musical system with input power below 200 watts, Wireless microphone, Video camera, Webcam (Finished product), Smart speakers (with and without display), Bluetooth speaker; Rs.55,000/- For Power adaptors for audio, video & similar electronic apparatus, Electronic musical systems with input power 200 watts and above, Optical disc players with built in amplifier of input power 200 watts and above, Plasma/LCD/LED television of screen size up to 32’’; Rs.75,000/- For Plasma/LCD/LED television of screen size up to 32’’ and above, Amplifier with input power 2000 watts and above, Television other than plasma/LCD/LED TVs

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	5000	Indicated charges are excluding BIS sealed samples
7(Heating under normal operating conditions)	-	10000	Indicated charges are excluding BIS sealed samples
8(Constructional requirements with regard to the protection against electric shock)	-	5000	Indicated charges are excluding BIS sealed samples
9(Electric shock hazard under normal operating conditions)	-	5000	Indicated charges are excluding BIS sealed samples
10(Insulation requirements)	-	10000	Indicated charges are excluding BIS sealed samples
11(Fault conditions)	-	15000	Indicated charges are excluding BIS sealed samples
12(Mechanical strength)	-	10000	Indicated charges are excluding BIS sealed samples
13(CLEARANCES and CREEPAGE DISTANCES)	-	10000	Indicated charges are excluding BIS sealed samples
15(TERMINALS)	-	5000	Indicated charges are excluding BIS sealed samples
16(External flexible cords)	-	5000	Indicated charges are excluding BIS sealed samples
17(Electrical connections and mechanical fixings)	-	5000	Indicated charges are excluding BIS sealed samples
19(Stability and mechanical hazards)	-	10000	Indicated charges are excluding BIS sealed samples
20(Resistance to fire)	-	10000	Indicated charges are excluding BIS sealed samples
6(Hazardous radiations)	-	0	NA
14(Components)	-	0	NA
18(Mechanical strength of picture tubes and protection against the effects of implosion)	-	0	NA
5(Marking and instructions)	-	5000	-
7(Heating under normal operating conditions)	-	10000	-
8(Constructional requirements with regard to the protection against electric shock)	-	5000	-
9(Electric shock hazard under normal operating conditions)	-	5000	-
10(Insulation requirements)	-	10000	-
11(Fault conditions)	-	15000	-
12(Mechanical strength)	-	10000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	10000	-
15(TERMINALS)	-	5000	-
16(External flexible cords)	-	5000	-
17(Electrical connections and mechanical fixings)	-	5000	-
19(Stability and mechanical hazards)	-	10000	-
20(Resistance to fire)	-	10000	-
6(Hazardous radiations)	-	0	-
14(Components)	-	0	-
18(Mechanical strength of picture tubes and protection against the effects of implosion)	-	0	-

24 Sep, 2026

-
Ionization radiation test measurement (Cl.6.1), Laser radiation test measurement (Cl.6.2), Light emitting diodes (LEDs) (Cl.6.3), Components (Cl.14), Mechanical strength of picture tubes and protection against effects of implosion (Cl.18). Included w.e.f. 5-8-2021.

IS 16242 : Part 1 (2014)

Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS

75000 View breakup
Rs.65,000/- for UPS/Inverters upto 2 kVA

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.6(Power interface)	-	5000	Charges are excluding BIS samples
4.7(Marking & instructions)	-	2000	Charges are excluding BIS samples
5.1(Protection against shock and energy hazards)	-	5000	Charges are excluding BIS samples
5.2(Requirement of auxiliary circuits)	-	5000	Charges are excluding BIS samples
5.3(Protective earthing and bonding)	-	3000	Charges are excluding BIS samples
5.4(AC and DC power isolation)	-	2000	Charges are excluding BIS samples
5.5(Over current and earth fault condition)	-	3000	Charges are excluding BIS samples
5.6(Safety interlocks)	-	5000	Charges are excluding BIS samples
5.7(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	5000	Charges are excluding BIS samples
6.1(Wiring, connections and supply)	-	3000	Charges are excluding BIS samples
6.2(Connection to power)	-	3000	Charges are excluding BIS samples
6.3(Wiring terminals for external power conductors)	-	3000	Charges are excluding BIS samples
7.1(Enclosure)	-	2000	Charges are excluding BIS samples
7.2(STABILITY)	-	3000	Charges are excluding BIS samples
7.3(MECHANICAL STRENGTH)	-	5000	Charges are excluding BIS samples
7.4(Construction details)	-	5000	Charges are excluding BIS samples
7.5(Resistance to fire)	-	3000	Charges are excluding BIS samples
7.6(Battery location)	-	5000	Charges are excluding BIS samples
7.7(Temperature rise)	-	4000	Charges are excluding BIS samples
8.1(General procision for earth leakage)	-	3000	Charges are excluding BIS samples
8.2(Electric Strength)	-	3000	Charges are excluding BIS samples
8.3(Abnormal operating and fault conditions)	-	5000	Charges are excluding BIS samples
9.0(Connection to telecommunication networks)	-	3000	Charges are excluding BIS samples
Annex I.5(Solid-state backfeed protection)	-	0	NA
I.5(transient overvoltages)	-	0	NA

24 Sep, 2026

-
Single Phase only. Restricted upto and including 5 kVA Excluding: Components (Cl.4.5)

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.6(Power interface .)	-	3000	Charges are excluding BIS sent samples.
1.7(Markings and instructions)	-	2000	Charges are excluding BIS sent samples.
2.1(Protection from electric shock and energy hazards)	-	2000	Charges are excluding BIS sent samples.
2.2(SELV circuits)	-	2000	Charges are excluding BIS sent samples.
2.3(TNV circuits)	-	2000	Charges are excluding BIS sent samples.
2.4(Limited current circuits)	-	3000	Charges are excluding BIS sent samples.
2.5(Limited power sources .)	-	3000	Charges are excluding BIS sent samples.
2.6(Provisions for earthing and bonding)	-	3000	Charges are excluding BIS sent samples.
2.7(Overcurrent and earth fault protection in primary circuits)	-	3000	Charges are excluding BIS sent samples.
2.9(Electrical insulation)	-	5000	Charges are excluding BIS sent samples.
2.10(Clearances, creepage distances and distances through insulation)	-	3000	Charges are excluding BIS sent samples.
3.1(General)	-	2000	Charges are excluding BIS sent samples.
3.2(Connection to a mains supply)	-	2000	Charges are excluding BIS sent samples.
3.3(Wiring terminals for connection of external conductors)	-	2000	Charges are excluding BIS sent samples.
3.4(Disconnection from the mains supply)	-	2000	Charges are excluding BIS sent samples.
3.5(Interconnection of equipment)	-	2000	Charges are excluding BIS sent samples.
4.1(Stability)	-	3000	Charges are excluding BIS sent samples.
4.2(Mechanical strength)	-	2500	Charges are excluding BIS sent samples.
4.3(Design and construction)	-	2500	Charges are excluding BIS sent samples.
4.4(Protection against hazardous moving parts)	-	3000	Charges are excluding BIS sent samples.
4.5(Thermal requirements)	-	4000	Charges are excluding BIS sent samples.
4.6(Openings in enclosures)	-	2000	Charges are excluding BIS sent samples.
4.7(Resistance to fire)	-	3000	Charges are excluding BIS sent samples.
5.1(Touch current and protective conductor curren)	-	2500	Charges are excluding BIS sent samples.
5.2(Electric strength)	-	2500	Charges are excluding BIS sent samples.
5.3(Abnormal operating and fault conditions)	-	4000	Charges are excluding BIS sent samples.
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	3000	Charges are excluding BIS sent samples.
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	2500	Charges are excluding BIS sent samples.
6.3(Protection of the telecommunication wiring system from overheating)	-	5000	Charges are excluding BIS sent samples.
7.1(General)	-	2500	Charges are excluding BIS sent samples.
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	3000	Charges are excluding BIS sent samples.
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	4000	Charges are excluding BIS sent samples.
7.4(Insulation between primary circuits and cable distribution systems)	-	5000	Charges are excluding BIS sent samples.
2.8(Safety interlocks)	-	0	.
1.6(Power interface .)	-	3000	-
1.7(Markings and instructions)	-	2000	-
2.1(Protection from electric shock and energy hazards)	-	2000	-
2.2(SELV circuits)	-	2000	-
2.3(TNV circuits)	-	2000	-
2.4(Limited current circuits)	-	3000	-
2.5(Limited power sources .)	-	3000	-
2.6(Provisions for earthing and bonding)	-	3000	-
2.7(Overcurrent and earth fault protection in primary circuits)	-	3000	-
2.9(Electrical insulation)	-	5000	-
2.10(Clearances, creepage distances and distances through insulation)	-	3000	-
3.1(General)	-	2000	-
3.2(Connection to a mains supply)	-	2000	-
3.3(Wiring terminals for connection of external conductors)	-	2000	-
3.4(Disconnection from the mains supply)	-	2000	-
3.5(Interconnection of equipment)	-	2000	-
4.1(Stability)	-	3000	-
4.2(Mechanical strength)	-	2500	-
4.3(Design and construction)	-	2500	-
4.4(Protection against hazardous moving parts)	-	3000	-
4.5(Thermal requirements)	-	4000	-
4.6(Openings in enclosures)	-	2000	-
4.7(Resistance to fire)	-	3000	-
5.1(Touch current and protective conductor curren)	-	2500	-
5.2(Electric strength)	-	2500	-
5.3(Abnormal operating and fault conditions)	-	4000	-
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	3000	-
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	2500	-
6.3(Protection of the telecommunication wiring system from overheating)	-	5000	-
7.1(General)	-	2500	-
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	3000	-
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	4000	-
7.4(Insulation between primary circuits and cable distribution systems)	-	5000	-

24 Sep, 2026

-
Visual display units, video monitors of screen size Restricted upto 80”. Except CRT. Excluding: Component (Cl.1.5), Ionizing radiation (Cl.4.3.13.2), Effect of UV radiation on materials (Cl. 4.3.13.3), Human exposure to UV radiation (Cl.4.3.13.4), Laser including LED (Cl.4.3.13.5).

Bureau of Indian Standards

The National Standards Body of India

AA Electro Magnetic Laboratory Pvt Ltd, Gurugram

Plot174, udyog vihar, phase 4, Gurgaon, Gurugram, Haryana, 122015

8870082081 info@aaemtlabs.com

Scope List