BIS - LIMS (Laboratory Information Management System)

RTRC LIMITED, GURUGRAM

Plot No. 296, Sector-7, Phase-II,Industrial Estate,IMT Manesar, Gurugram, Gurugram, Gurugram, Haryana, 122050

8826495200 qa@rtrc.in

Scope List

Reset

48 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

Electrical conductor(EC) grade aluminum redraw rods

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	5000	-
Cl-6.2(Chemical analysis of the material)	-	0	-
Cl.6.1 as per IS 4026(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.6.1 as per IS 4026(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Magnesium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Zinc - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Titanium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl-5(Manufacture)	-	0	-
Cl-7.1(General condition for delivery and inspection relating)	-	0	-
Cl-9(Ultimate tensile strength and elongation)	-	2500	-
Cl-10.1(Resistivity)	-	2500	-
Cl-10.1(electrical conductivity)	-	0	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	0	-
Cl-11(Dimensions)	-	500	-
Cl-13(Finish and freedom from defects)	-	500	-
Cl-14(Rejection and retest)	-	0	-
Cl-16(Marking)	-	0	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	0	-
CL 11(DIMENSIONS)	-	0	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	0	-
9(Elongation)	-	0	-
12(Joint)	-	0	-
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	0	-
Cl-6.2(Chemical analysis of the material)	-	0	-
Cl.6.1 as per IS 4026(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Magnesium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Zinc - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Titanium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl-5(Manufacture)	-	0	-
Cl-7.1(General condition for delivery and inspection relating)	-	0	-
Cl-9(Ultimate tensile strength and elongation)	-	0	-
Cl-10.1(Resistivity)	-	0	-
Cl-10.1(electrical conductivity)	-	0	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	0	-
Cl-11(Dimensions)	-	0	-
Cl-13(Finish and freedom from defects)	-	0	-
Cl-14(Rejection and retest)	-	0	-
Cl-16(Marking)	-	0	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	0	-
CL 11(DIMENSIONS)	-	0	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	0	-
9(Elongation)	-	0	-
12(Joint)	-	0	-
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	0	-
Cl-6.2(Chemical analysis of the material)	-	0	-
Cl.6.1 as per IS 4026(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Magnesium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Zinc - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Titanium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl-5(Manufacture)	-	0	-
Cl-7.1(General condition for delivery and inspection relating)	-	0	-
Cl-9(Ultimate tensile strength and elongation)	-	0	-
Cl-10.1(Resistivity)	-	0	-
Cl-10.1(electrical conductivity)	-	0	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	0	-
Cl-11(Dimensions)	-	0	-
Cl-13(Finish and freedom from defects)	-	0	-
Cl-14(Rejection and retest)	-	0	-
Cl-16(Marking)	-	0	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	0	-
CL 11(DIMENSIONS)	-	0	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	0	-
9(Elongation)	-	0	-
12(Joint)	-	0	-

03 Apr, 2027

-
Included w.e.f 12.09.2025

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

Aluminium Conductor for Overhead Transmission Purposes — Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	1000	Type Test-Rs 18000 up to 100 sq mm. Rs 100000 (150 Sq mm to 200 sq mm). Rs 150000 (400 sq mm to 560 sq mm).
Cl-6.1.1(chemical composition of high carbon steel)	-	0	-
Cl-6.2(zinc used for galvanizing)	-	0	-
Cl-7(Freedom From Defects)	-	1000	Type Test-Rs 18000 up to 100 sq mm. Rs 100000 (150 Sq mm to 200 sq mm). Rs 150000 (400 sq mm to 560 sq mm).
Cl-8.1(Wires-Nominal Sizes)	-	1000	Type Test-Rs 18000 up to 100 sq mm. Rs 100000 (150 Sq mm to 200 sq mm). Rs 150000 (400 sq mm to 560 sq mm).
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	1000	-
Cl-9.1(Joint in Wires)	-	0	-
Cl-9.2(Aluminium Wires)	-	0	-
Cl-9.3(Galvanized Steel Wires)	-	0	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	5000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	5000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	5000	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	2000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	5000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	2500	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	5000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	0	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	2000	-
Cl- 13.6(Steel wires- Breaking load test)	-	2000	-
Cl- 13.7(Steel wires- Ductility test)	-	2000	-
Cl- 13.8(Steel wires- Wrapping test)	-	2000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	2500	-
Cl-13.7.1(Torsion Test)	-	2500	-
Cl-13.7.2(Elongation Test)	-	2500	-
Cl-11.1(Standard Length)	-	1000	-
Cl-11.2(Random Lengths)	-	0	-

03 Apr, 2027

-
Included w.e.f 11.09.2025 Exclusion: Cl- 13.13 (Conductor- Surface condition test on stranded conductor),Cl- 13.14 (Conductor- Ultimate tensile strength test on stranded conductor),Cl- 13.15 (Conductor- Corona test) and Cl-13.16 (Conductor- Radio interference voltage test)

IS 5950 (2024)

Shot Firing Cables (for Use Other than in Shafts) - Specification (Second Revision)

Shot Firing Cables (for Use Other Than in Shafts) — Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Section-2, Cl-3(CONDUCTOR)	-	150	-
Section-2, Cl-4(INSULATION)	-	150	-
Section-2, Cl-5(SHEATH)	-	150	-
Section-3, Cl-6(CONDUCTOR)	-	300	-
Section-3, Cl-7.1.1(Thickness of Insulation & Sheath)	-	300	-
Section-3, Cl-7.1.2(Type II)	-	250	-
Section-3, Cl-7.2(Tolerance on Thickness of Insulation)	-	100	-
Section-3, Cl-7.3(Colour of Insulation)	-	100	-
Section-3, Cl-8.1(Single-Core)	-	500	-
Section-3, Cl-8.2(Tolerance on Thickness of Sheath)	-	500	-
Section-3, Cl-8.3(Color of Sheath)	-	500	-
Cl-10.2(Voltage Test)	-	1000	-
Cl-10.3(Spark Test)	-	500	-
Cl-10.4(Flammability Test)	-	500	-
Cl-9.1 (a)(Annealing test;)	-	500	-
Cl-9.1 (b)(Conductor resistance test)	-	1000	-
Cl-9.1 (c)(Test for thickness of insulation and sheath)	-	500	-
Cl-9.1 (d) 1(Tensile strength and elongation at break)	-	500	-
Cl-9.1 (d) 2(Ageing in air oven)	-	500	-
Cl-9.1 (d) 3(Loss of mass test)	-	200	-
Cl-9.1 (d) 4(Hot deformation)	-	300	-
Cl-9.1 (d) 5(Heat shock)	-	500	-
Cl-9.1 (d) 6(hrinkage)	-	500	-
Cl-9.2 , e(Insulation resistance test)	-	500	-

03 Apr, 2027

-
Included w.e.f 29.09.2025

IS 17046 (2018)

Fibre Optic Cable for Cable TV Application

130000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Design and construction of aerial metal free optical fibre cable)	-	0	-
3.2(Fibre used in the cable)	-	0	-
3.3(Self-supporting metal free aerial optical fibre cable)	-	0	-
3.4(Technical Requirements)	-	4500	-
3.5(Mechanical Characteristics)	-	4500	-
3.6(Environmental Characteristic of Fibre)	-	4500	-
3.7(Optical Fibre Cable Construction Specifications)	-	1000	-
3.8(Mechanical Characteristics and Tests on Optical Fibre Cable)	-	100000	-
4(Marking)	-	500	-

03 Apr, 2027

-
Included w.e.f 29.09.2025

IS 2465 (1984)

Specification for cables for motor vehicles (Second Revision)

specification for cables for motor vehicles

28350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Insulation)	-	200	-
7.3(Insulation)	-	200	-
8(Core Identification)	-	200	-
9(Laying up of cores)	-	200	-
10.1.1(Sheathing )	-	200	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	200	-
3 & 6(Construction)	-	200	-
3 & 6(Diameter of wire(mm))	-	1000	-
3 & 6(Annealing test)	-	500	-
3 & 6(Persulphate Test)	-	1000	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	1000	-
7.2, 10.3, 11(Dimensions & thickness )	-	200	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
7.2, 10.3, 11(Overall Dimension (mm))	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	500	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	2500	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	1000	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	0	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	1000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	0	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	1000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	0	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	1000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	0	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	500	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	0	-
14(High Voltage Test)	-	3500	-
15(SPARK TEST FOR SINGLE CORE GENERAL WIRING CABLES)	-	1000	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	1000	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	2000	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	1000	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	1000	-
20.3(EFFECT OF BRAKE FLUID)	-	0	-
20.3(EFFECT OF DIESEL)	-	500	-
20.3(EFFECT OF DIESEL)	-	0	-
20.3(Increase in average diameter %)	-	0	-
20.3(Wrapping test)	-	250	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	500	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
22.1(FLAMMABILITY TEST)	-	3000	-
22.1(FLAMMABILITY TEST)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
24.2(PACKING AND MARKING)	-	0	-
24.2.1(PACKING AND MARKING)	-	0	-
12.1.b(Persulphate test (when applicable))	-	1000	-
6.1, 12.3, 12.1.c(Conductor Resistance)	-	0	-
12.1.e4(Hot deformation)	-	1000	-
12.1.e5(Heat Shock)	-	0	-
CL.12.1 (e) 2(Tensile Strength After Ageing)	-	0	-
CL.12.1 (e) 2(Elongation After Ageing)	-	0	-
CL.12.1 (e) 2(Tensile Strength Variation)	-	0	-
CL.12.1 (e) 2(Elongation Variation)	-	0	-
CL.12.1 (e) 2(Elongation Variation)	-	0	-
Cl.12 (e) 5(Heat shock test)	-	0	-
Cl.12 (e) 4(Hot Deformation Test)	-	0	-
Cl.12 (e) 6(Shrinkage Test)	-	0	-
Cl.12 (e) 6(Shrinkage Test (Cracks Observed))	-	0	-
Cl. 12.1 (e) 3(Loss of Mass Insulation)	-	1000	-

03 Apr, 2027

-
Included w.e.f 29.09.2025

IS 9567 (2001)

Tin or tin - Lead coated copper wire - Specificaiton (First Revision)

Tin or tin-lead coated copper wire — specification

15400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	0	-
4.2(Resistivity)	-	1000	-
4.3(Details of Coating)	-	0	-
4.4(Diameter of Coated Wire)	-	2000	-
5(Packing and Marking)	-	0	-
6.3.1(Resistance Test)	-	1000	-
6.4.1(Measurement of Diameter)	-	1000	-
6.4.2(Elongation and Breaking Strength Test)	-	2000	-
6.4.3(Bend Test)	-	1000	-
6.4.4(Solderability Test)	-	1000	-
6.4.5(Continuity of Coating Test)	-	1000	-
6.4.6(Adherence of Coating Test)	-	1000	-

03 Apr, 2027

-
Included w.e.f 29.09.2025

IS 2593 (1984)

Flexible Cables for Miners' Cap-lamps

Flexible Cables for Miners' Cap- Lamps — Specification

37000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	1000	-
3.1.1(Per sulphate test )	-	2000	-
3.1.2(Resistance test )	-	500	-
4.1(INSULATION)	-	500	-
5.1(CENTRAL STRAIN CORD)	-	500	-
6.1(SHEATH)	-	1000	-
7.1(Construction : Conductor )	-	500	-
8.1(Thickness of Insulation - Average )	-	500	-
8.1(Thickness of Insulation - minimum)	-	500	-
9.1(IDENTIFICATION OF CORES)	-	0	-
10.1(LAYING UP)	-	0	-
11.1(SHEATH : Application )	-	0	-
11.2(Thickness of Sheath -average )	-	500	-
12.2(Thickness of Sheath - Minimum)	-	500	-
11.3(Coulor of sheath )	-	1000	-
12.1(OVERALL DIAMETER)	-	1000	-
13.1 b)(Annealing test)	-	500	-
13.1 e) 1)(Physical tests for insulation: Tensile strength )	-	500	-
13.1 e) 1)(Physical tests for insulation: elongation at break )	-	500	-
13.1 e) 1)(Physical tests for Sheath : Tensile strength )	-	500	-
13.1 e) 1)(Physical tests for Sheath: elongation at break )	-	500	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength variation )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	500	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	500	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : Tensile Strength variation )	-	500	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : elongation variation at break)	-	500	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : Tensile Strength variation )	-	500	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : elongation variation at break)	-	500	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Tensile strength variation )	-	2500	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Elongation variation )	-	2500	-
14.1(Voltage test)	-	3500	-
14.2(Flammability test)	-	3500	-
14.3.1(Centre Strain Cord : Breaking Load )	-	1000	-
14.3.2(Centre Strain Cord : Determination of Copper and Manganese Content)	-	0	-
14.4(Checking of overall diameter of cable)	-	500	-
14.5(Resistance of sheath to fatty acids : Weigth Increase )	-	2000	-
14.5(Resistance of sheath to fatty acids : Diameter Increase )	-	2000	-
15.1(MANUFACTURER'S IDENTIFICATION)	-	500	-
16.1(Packing )	-	0	-
16.2(Marking )	-	0	-
16.2.1(Standards Mark )	-	0	-
6.1(Resistance of Sheath to Fatty Acids - 14.5 - diameter increase)	-	0	-
6.1(Resistance of Sheath to Fatty Acids - 14.5 - weight increase)	-	0	-
5.1(Copper and Manganese Content - Cl 14.3.2)	-	1000	-
3.1.1(mass of copper - Cl 7.1 of IS 8130 read with Method B of IS 10810 (Part 4))	-	2500	-
3.1(CONDUCTOR)	-	0	-
3.1.1(Per sulphate test )	-	0	-
3.1.2(Resistance test )	-	0	-
4.1(INSULATION)	-	0	-
5.1(CENTRAL STRAIN CORD)	-	0	-
6.1(SHEATH)	-	0	-
7.1(Construction : Conductor )	-	0	-
8.1(Thickness of Insulation - Average )	-	0	-
8.1(Thickness of Insulation - minimum)	-	0	-
9.1(IDENTIFICATION OF CORES)	-	0	-
10.1(LAYING UP)	-	0	-
11.1(SHEATH : Application )	-	0	-
11.2(Thickness of Sheath -average )	-	0	-
12.2(Thickness of Sheath - Minimum)	-	0	-
11.3(Coulor of sheath )	-	0	-
12.1(OVERALL DIAMETER)	-	0	-
13.1 b)(Annealing test)	-	0	-
13.1 e) 1)(Physical tests for insulation: Tensile strength )	-	0	-
13.1 e) 1)(Physical tests for insulation: elongation at break )	-	0	-
13.1 e) 1)(Physical tests for Sheath : Tensile strength )	-	0	-
13.1 e) 1)(Physical tests for Sheath: elongation at break )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength variation )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : Tensile Strength variation )	-	0	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : Tensile Strength variation )	-	0	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : elongation variation at break)	-	0	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Tensile strength variation )	-	0	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Elongation variation )	-	0	-
14.1(Voltage test)	-	0	-
14.2(Flammability test)	-	0	-
14.3.1(Centre Strain Cord : Breaking Load )	-	0	-
14.3.2(Centre Strain Cord : Determination of Copper and Manganese Content)	-	0	-
14.4(Checking of overall diameter of cable)	-	0	-
14.5(Resistance of sheath to fatty acids : Weigth Increase )	-	0	-
14.5(Resistance of sheath to fatty acids : Diameter Increase )	-	0	-
15.1(MANUFACTURER'S IDENTIFICATION)	-	0	-
16.1(Packing )	-	0	-
16.2(Marking )	-	0	-
16.2.1(Standards Mark )	-	0	-

03 Apr, 2027

-
Included w.e.f 11.09.2025

IS 4412 (1981)

Specification for copper wires for general engineering purposes (First Revision)

Copper wire for general engineering purposes

15300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 ( Table -1)(Copper+Silver)	-	900	-
Clause 4.1 ( Table -1)(phosphorus)	-	900	-
Clause 4.1 ( Table -1)(Antimony)	-	900	-
Clause 4.1 ( Table -1)(Arsenic)	-	900	-
Clause 4.1 ( Table -1)(Bismuth)	-	900	-
Clause 4.1 ( Table -1)(Iron)	-	900	-
Clause 4.1 ( Table -1)(Lead)	-	900	-
Clause 4.1 ( Table -1)(Nckel)	-	900	-
Clause 4.1 ( Table -1)(Selenium+Tellurium)	-	900	-
Clause 4.1 ( Table -1)(Tellurium)	-	900	-
Clause 4.1 ( Table -1)(Tin)	-	900	-
Clause 4.1 ( Table -1)(Total Impurities)	-	900	-
5.1(Tensile Test)	-	900	-
5.2(Embrittlement Test)	-	900	-
6(Freedom from defect)	-	900	-
7.1(Diameter and Tolerances)	-	900	-
Clause 4(Chemical Composition)	-	900	-

03 Apr, 2027

-
Included w.e.f.10.09.2025

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

CROSSLINKED POLYETHYLENE INSULATED PVC SHEATHED CABLES, FOR WORKING VOLTAGES UP TO AND INCLUDING 1100 VOLTS

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5, Table-1 (i)(Tensile strength)	-	500	Single core (normal)-16000 Single core (FR)-31000 Single core (FRLSH)-36000 Single core (LSHF)-43000 Additional Charge 1500 for each core
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	500	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	500	Single core (normal)-16000 Single core (Cat-C1)-31000 Single core (Cat-C2)-36000 Single core (Cat-C3)-43000 Additional Charge Rs.1500 for each additional core
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	0	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	500	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	0	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	0	-
Cl-5, Table-1 (iv)(Shrinkage)	-	500	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	500	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	500	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	0	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	0	-
Cl-7(Armouring)	-	0	-
Cl-8(Outer Sheath)	-	0	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	0	-
Cl-11(Core Identification)	-	0	-
Cl-12(Laying up of Cores)	-	0	-
Cl-13(Inner Sheath (Common Covering))	-	500	-
Cl-14.1(Armouring- Application)	-	0	-
Cl-14.1.2(armour round wires/formed wires)	-	0	-
Cl-14.2(Type of Armour)	-	0	-
Cl-14.3(Dimensions)	-	500	-
Cl-14.4(Joints)	-	0	-
Cl-14.5(Resistance)	-	500	-
Cl-15.3(Thickness of Outer Sheath)	-	500	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	500	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	500	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	500	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	500	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	500	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	500	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	500	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	500	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	500	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	500	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	500	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	500	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	1000	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	1000	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	1000	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	1000	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	500	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	500	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	5500	As applicable
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	0	As applicable
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	0	As applicable
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	0	As applicable
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	0	As applicable
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	0	As applicable
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	0	As applicable
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	0	As applicable
Cl-17.2(High voltage test)	-	0	As applicable
Cl-17.3(Flammability test)	-	0	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	2500	Additional charges, if applicable
Cl-17.5(Flame retardance test on single cable)	-	2500	Additional charges, if applicable
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	10000	Additional charges, if applicable
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	2500	Additional charges, if applicable
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	2500	Additional charges, if applicable
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	0	Additional charges, if applicable
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	3500	Additional charges, if applicable
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	3500	Additional charges, if applicable
Cl-16.4 (i)(Cold bend test for outer sheath)	-	0	As applicable
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	0	As applicable
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	0	As applicable
Cl-4(Conductors -Material)	-	0	-
Cl-5, Table-1 (i)(Tensile strength)	-	0	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	0	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	0	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	0	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	0	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	0	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	0	-
Cl-5, Table-1 (iv)(Shrinkage)	-	0	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	0	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	0	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	0	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	0	-
Cl-7(Armouring)	-	0	-
Cl-8(Outer Sheath)	-	0	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	0	-
Cl-11(Core Identification)	-	0	-
Cl-12(Laying up of Cores)	-	0	-
Cl-13(Inner Sheath (Common Covering))	-	0	-
Cl-14.1(Armouring- Application)	-	0	-
Cl-14.1.2(armour round wires/formed wires)	-	0	-
Cl-14.2(Type of Armour)	-	0	-
Cl-14.3(Dimensions)	-	0	-
Cl-14.4(Joints)	-	0	-
Cl-14.5(Resistance)	-	0	-
Cl-15.3(Thickness of Outer Sheath)	-	0	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	0	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	0	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	0	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	0	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	0	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	0	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	0	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	0	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	0	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	0	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	0	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	0	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	0	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	0	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	0	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	0	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	0	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	0	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	0	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	0	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	0	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	0	-
Cl-17.2(High voltage test)	-	0	-
Cl-17.3(Flammability test)	-	0	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	0	-
Cl-17.5(Flame retardance test on single cable)	-	0	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	0	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	0	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	0	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	0	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	0	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	0	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	0	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	0	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	0	-
Cl-4(Conductors -Material)	-	0	-
Cl-5, Table-1 (i)(Tensile strength)	-	0	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	0	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	0	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	0	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	0	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	0	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	0	-
Cl-5, Table-1 (iv)(Shrinkage)	-	0	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	0	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	0	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	0	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	0	-
Cl-7(Armouring)	-	0	-
Cl-8(Outer Sheath)	-	0	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	0	-
Cl-11(Core Identification)	-	0	-
Cl-12(Laying up of Cores)	-	0	-
Cl-13(Inner Sheath (Common Covering))	-	0	-
Cl-14.1(Armouring- Application)	-	0	-
Cl-14.1.2(armour round wires/formed wires)	-	0	-
Cl-14.2(Type of Armour)	-	0	-
Cl-14.3(Dimensions)	-	0	-
Cl-14.4(Joints)	-	0	-
Cl-14.5(Resistance)	-	0	-
Cl-15.3(Thickness of Outer Sheath)	-	0	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	0	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	0	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	0	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	0	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	0	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	0	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	0	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	0	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	0	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	0	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	0	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	0	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	0	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	0	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	0	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	0	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	0	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	0	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	0	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	0	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	0	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	0	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	0	-
Cl-17.2(High voltage test)	-	0	-
Cl-17.3(Flammability test)	-	0	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	0	-
Cl-17.5(Flame retardance test on single cable)	-	0	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	0	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	0	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	0	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	0	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	0	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	0	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	0	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	0	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	0	-
Cl-4(Conductors -Material)	-	0	-
Cl-5, Table-1 (i)(Tensile strength)	-	-	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	-	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	-	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	-	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	-	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	-	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	-	-
Cl-5, Table-1 (iv)(Shrinkage)	-	-	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	-	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	-	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	-	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	-	-
Cl-7(Armouring)	-	-	-
Cl-8(Outer Sheath)	-	-	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	-	-
Cl-11(Core Identification)	-	-	-
Cl-12(Laying up of Cores)	-	-	-
Cl-13(Inner Sheath (Common Covering))	-	-	-
Cl-14.1(Armouring- Application)	-	-	-
Cl-14.1.2(armour round wires/formed wires)	-	-	-
Cl-14.2(Type of Armour)	-	-	-
Cl-14.3(Dimensions)	-	-	-
Cl-14.4(Joints)	-	-	-
Cl-14.5(Resistance)	-	-	-
Cl-15.3(Thickness of Outer Sheath)	-	-	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	-	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	-	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	-	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	-	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	-	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	-	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	-	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	-	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	-	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	-	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	-	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	-	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	-	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	-	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	-	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	-	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	-	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	-	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	-	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	-	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	-	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	-	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	-	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	-	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	-	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	-	-
Cl-17.2(High voltage test)	-	-	-
Cl-17.3(Flammability test)	-	-	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	-	-
Cl-17.5(Flame retardance test on single cable)	-	-	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	-	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	-	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	-	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	-	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	-	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	-	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	-	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	-	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	-	-
Cl-4(Conductors -Material)	-	-	-

03 Apr, 2027

-
Included w.e.f.10.09.2025

IS 12444 (2020)

Copper Wire Rods for Electrical Applications — Specification ( First Revision )

Copper Wire Rods for Electrical Applications — Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1(Te)	-	1000	-
5.1 Table-1(Se)	-	1000	-
5.1 Table-1(Bi)	-	1000	-
5.1 Table-1(Se+Te+Bi)	-	0	-
5.1 Table-1(Sb)	-	1000	-
5.1 Table-1(As)	-	1000	-
5.1 Table-1(Sn)	-	1000	-
5.1 Table-1(Pb)	-	1000	-
5.1 Table-1(Fe)	-	1000	-
5.1 Table-1(Ni)	-	1000	-
5.1 Table-1(S)	-	1000	-
5.1 Table-1(Ag)	-	1000	-
5.1 Table-1(O)	-	1000	-
5.1 Table-1(Maximum Allowable Total Impurities)	-	500	-
6.1(Dimension)	-	0	-
6.2.2(Ovality)	-	0	-
7.0(Freedom from Defects)	-	0	-
8.1(Tensile Strength)	-	2500	-
8.2(Surface Compression Test)	-	1000	-
Cl-9.1, Table-4(Volume Resistivity)	-	2500	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	1500	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-
Cl-9.1, Table-4(Volume Resistivity)	-	0	-
Cl-9.1, Table-4(Mass Resistivity)	-	0	-
Cl-9.1, Table-4(Electrical Conductivity)	-	0	-
10.5(Microscopic Examination)	-	0	-
9.2.1.1(Electrical Properties)	-	0	-
9.2.1.2(Electrical Properties)	-	0	-
9.2.1.3(Electrical Properties)	-	0	-
13(Mechanical Strength)	-	0	-
8.2.2(Calculated resistance)	-	0	-
Cl-9.2.2(Electrical Properties)	-	0	-
7.2(Surface Oxide)	-	0	-

03 Apr, 2027

-
Included w.e.f 16.09.2025

IS 16659 (2017)

Fluids for electrotechnical applications - Unused natural esters for transformers and similar electrical equipment

Natural Ester Fluids

34500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1-Table 1-i)(Appearance)	-	1000	-
4.1-Table 1-ii)(Viscosity at 100 °C)	-	1000	-
4.1-Table 1-iii)(Viscosity at 40 °C)	-	1000	-
4.1-Table 1-iv)(Pour point)	-	1500	-
4.1-Table 1-v)(Water content)	-	2000	-
4.1-Table 1-vi)(Density at 20 °C)	-	1500	-
4.1-Table 1-vii)(Breakdown voltage)	-	2500	-
4.1-Table 1-viii)(Dissipation factor (tan δ) 90 °C)	-	2500	-
4.1-Table 1-ix)(Soluble acidity)	-	1500	-
4.1-Table 1-x)(Corrosive sulfur DBDS)	-	2500	-
4.1-Table 1-xi)(Total additives)	-	7000	-
4.1-Table 1-xii)(Performance – Salient properties after oxidation stability test)	-	7500	-
4.1-Table 1-xiii)(Total acidity)	-	0	-
4.1-Table 1-xiv)(Viscosity at 40 °C)	-	0	-
4.1-Table 1-xv)(DDF (tan δ) at 90 °C)	-	0	-
4.1-Table 1-xvi)(Fire point Flash point)	-	3000	-
4.1-Table 1-i)(Appearance)	-	0	-
4.1-Table 1-ii)(Viscosity at 100 °C)	-	0	-
4.1-Table 1-iii)(Viscosity at 40 °C)	-	0	-
4.1-Table 1-iv)(Pour point)	-	0	-
4.1-Table 1-v)(Water content)	-	0	-
4.1-Table 1-vi)(Density at 20 °C)	-	0	-
4.1-Table 1-vii)(Breakdown voltage)	-	0	-
4.1-Table 1-viii)(Dissipation factor (tan δ) 90 °C)	-	0	-
4.1-Table 1-ix)(Soluble acidity)	-	0	-
4.1-Table 1-x)(Corrosive sulfur DBDS)	-	0	-
4.1-Table 1-xi)(Total additives)	-	0	-
4.1-Table 1-xii)(Performance – Salient properties after oxidation stability test)	-	0	-
4.1-Table 1-xiii)(Total acidity)	-	0	-
4.1-Table 1-xiv)(Viscosity at 40 °C)	-	0	-
4.1-Table 1-xv)(DDF (tan δ) at 90 °C)	-	0	-
4.1-Table 1-xvi)(Fire point Flash point)	-	0	-
4.3.3(Relative permittivity (dielectric constant))	-	0	-
4.1-Table 1-i)(Appearance)	-	0	-
4.1-Table 1-ii)(Viscosity at 100 °C)	-	0	-
4.1-Table 1-iii)(Viscosity at 40 °C)	-	0	-
4.1-Table 1-iv)(Pour point)	-	0	-
4.1-Table 1-v)(Water content)	-	0	-
4.1-Table 1-vi)(Density at 20 °C)	-	0	-
4.1-Table 1-vii)(Breakdown voltage)	-	0	-
4.1-Table 1-viii)(Dissipation factor (tan δ) 90 °C)	-	0	-
4.1-Table 1-ix)(Soluble acidity)	-	0	-
4.1-Table 1-x)(Corrosive sulfur DBDS)	-	0	-
4.1-Table 1-xi)(Total additives)	-	0	-
4.1-Table 1-xii)(Performance – Salient properties after oxidation stability test)	-	0	-
4.1-Table 1-xiii)(Total acidity)	-	0	-
4.1-Table 1-xiv)(Viscosity at 40 °C)	-	0	-
4.1-Table 1-xv)(DDF (tan δ) at 90 °C)	-	0	-
4.1-Table 1-xvi)(Fire point Flash point)	-	0	-
4.3.3(Relative permittivity (dielectric constant))	-	0	-

03 Apr, 2027

-
Included w.e.f 03.05.2024 Exclusion: Cl.4.1 Table-1 (xvii) (Biodegradation)

IS 16081 (2013)

Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes

Synthetic Ester Fluids

29000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General remarks)	-	0	-
5.1(Flash point and fire point)	-	0	-
5.3(Toxicity)	-	0	-
6.1(Classification)	-	0	-
6.2(Identification and general delivery requirements, sampling, packaging and disposal)	-	0	-
6.3(Storage)	-	0	-
6.4(Representative sampling)	-	0	-
6.5(Disposal and spillages)	-	0	-
7.1.2(Appearance)	-	1000	-
7.1.3(Density)	-	1500	-
7.1.4(Kinematic viscosity)	-	2500	-
7.1.5(Flash point and fire point)	-	3000	-
7.1.6(Pour point)	-	1500	-
7.1.7(Crystallization)	-	0	-
7.1.8(Water content)	-	2000	-
7.1.9(Acidity)	-	1500	-
7.1.10(Oxidation stability)	-	7000	-
8.1(Breakdown voltage)	-	2500	-
8.2(Dielectric dissipation factor, permittivity and d.c. resistivity)	-	4000	-
8.3(Gassing tendency)	-	2500	-
9(Specifications for synthetic organic esters used in transformers)	-	0	-
4(General remarks)	-	0	-
5.1(Flash point and fire point)	-	0	-
5.3(Toxicity)	-	0	-
6.1(Classification)	-	0	-
6.2(Identification and general delivery requirements, sampling, packaging and disposal)	-	0	-
6.3(Storage)	-	0	-
6.4(Representative sampling)	-	0	-
6.5(Disposal and spillages)	-	0	-
7.1.2(Appearance)	-	0	-
7.1.3(Density)	-	0	-
7.1.4(Kinematic viscosity)	-	0	-
7.1.5(Flash point and fire point)	-	0	-
7.1.6(Pour point)	-	0	-
7.1.7(Crystallization)	-	0	-
7.1.8(Water content)	-	0	-
7.1.9(Acidity)	-	0	-
7.1.10(Oxidation stability)	-	0	-
8.1(Breakdown voltage)	-	0	-
8.2(Dielectric dissipation factor, permittivity and d.c. resistivity)	-	0	-
8.3(Gassing tendency)	-	0	-
9(Specifications for synthetic organic esters used in transformers)	-	0	-

03 Apr, 2027

-
Included w.e.f 03.05.2024 Exclusion: Cl.5.2 (Biodegradation), Cl.7.1.1 (Colour)

IS 2590 (1987)

Specification for primary aluminium ingots for remelting for general engineering purposes (Second Revision)

Primary Aluminium Ingots For Remelting

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General requirements )	-	0	-
4(Manufacture )	-	0	-
5(Grades)	-	0	-
6.1(Chemical composition )	-	0	-
7.1(Shapes and sizes)	-	500	-
9(Marking)	-	0	-
Table-1, Clause - 6.1.1(Copper)	-	600	-
Table-1, Clause - 6.1.1(Iron)	-	600	-
Table-1, Clause - 6.1.1(Magnesium)	-	600	-
Table-1, Clause - 6.1.1(Manganese)	-	600	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	1200	-
Table-1, Clause - 6.1.1(Silicon)	-	600	-
Table-1, Clause - 6.1.1(Vanadium)	-	0	-
Table-1, Clause - 6.1.1(Zinc)	-	600	-
Table-1, Clause - 6.1.1(Other elements (each))	-	1000	-
Table-1, Clause - 6.1.1(Others Total)	-	0	-
Table-1, Clause - 6.1.1(Aluminium)	-	0	-
3.1(General requirements )	-	0	-
4(Manufacture )	-	0	-
5(Grades)	-	0	-
6.1(Chemical composition )	-	0	-
7.1(Shapes and sizes)	-	0	-
9(Marking)	-	0	-
Table-1, Clause - 6.1.1(Copper)	-	0	-
Table-1, Clause - 6.1.1(Iron)	-	0	-
Table-1, Clause - 6.1.1(Magnesium)	-	0	-
Table-1, Clause - 6.1.1(Manganese)	-	0	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	0	-
Table-1, Clause - 6.1.1(Silicon)	-	0	-
Table-1, Clause - 6.1.1(Vanadium)	-	0	-
Table-1, Clause - 6.1.1(Zinc)	-	0	-
Table-1, Clause - 6.1.1(Other elements (each))	-	0	-
Table-1, Clause - 6.1.1(Others Total)	-	0	-
Table-1, Clause - 6.1.1(Aluminium)	-	0	-

03 Apr, 2027

-
Included w.e.f. 20.11.2024

IS 11890 (1987)

Specification for high purity primary aluminium ingots for remelting for special applications

High Purity Primary Aluminium Ingots

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(SUPPLY OF YATERIAL)	-	0	-
Cl. No.4(MANUFACTURE)	-	0	-
Cl. No.5(GRADES)	-	0	-
Cl. No.6.1,Table no. 1(i)(Aluminium,)	-	0	-
Cl. No.6.1,Table no. 1(ii)(Copper)	-	600	-
Cl. No.6.1,Table no. 1(iii)(Silicon)	-	600	-
Cl. No.6.1,Table no. 1(iv)(Iron)	-	600	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	600	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	600	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	600	-
Cl. No.6.1,Table no. 1(viii)(Titanium + Vanadium)	-	1200	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	600	-
Cl. No.6.1,Table no. 1(x)(Other elements)	-	400	-
Cl. No.7(SHAPES AND SIZES)	-	500	-
Cl. No.8(SELECTION OF SAMPLES FOR ANALYSIS)	-	0	-
Cl. No.9(MARKING)	-	0	-
Cl. No.3(SUPPLY OF YATERIAL)	-	0	-
Cl. No.4(MANUFACTURE)	-	0	-
Cl. No.5(GRADES)	-	0	-
Cl. No.6.1,Table no. 1(i)(Aluminium,)	-	600	-
Cl. No.6.1,Table no. 1(ii)(Copper)	-	0	-
Cl. No.6.1,Table no. 1(iii)(Silicon)	-	0	-
Cl. No.6.1,Table no. 1(iv)(Iron)	-	0	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	0	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	0	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	0	-
Cl. No.6.1,Table no. 1(viii)(Titanium + Vanadium)	-	0	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	0	-
Cl. No.6.1,Table no. 1(x)(Other elements)	-	0	-
Cl. No.7(SHAPES AND SIZES)	-	0	-
Cl. No.8(SELECTION OF SAMPLES FOR ANALYSIS)	-	0	-
Cl. No.9(MARKING)	-	0	-
Cl. No.3(SUPPLY OF YATERIAL)	-	0	-
Cl. No.4(MANUFACTURE)	-	0	-
Cl. No.5(GRADES)	-	0	-
Cl. No.6.1,Table no. 1(i)(Aluminium,)	-	0	-
Cl. No.6.1,Table no. 1(ii)(Copper)	-	0	-
Cl. No.6.1,Table no. 1(iii)(Silicon)	-	0	-
Cl. No.6.1,Table no. 1(iv)(Iron)	-	0	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	0	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	0	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	0	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	0	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	0	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	0	-
Cl. No.6.1,Table no. 1(viii)(Titanium + Vanadium)	-	0	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	0	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	0	-
Cl. No.6.1,Table no. 1(x)(Other elements)	-	0	-
Cl. No.7(SHAPES AND SIZES)	-	0	-
Cl. No.8(SELECTION OF SAMPLES FOR ANALYSIS)	-	0	-
Cl. No.9(MARKING)	-	0	-

03 Apr, 2027

-
Included w.e.f. 10.06.2024

IS 4026 (2023)

ALUMINIUM INGOTS BILLETS AND WIRE BARS EC GRADE

Aluminium Ingots, Billets and Wires Bars (EC Grades)

8800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(SHAPES AND SIZES)	-	0.0	-
9, Table 1, i)(Aluminium, Min)	-	0.0	-
9, Table 1, ii)(Silicon)	-	600	-
9, Table 1, iii)(Iron)	-	600	-
9, Table 1, iv)(Copper)	-	600	-
9, Table 1, v)(Manganese)	-	600	-
9, Table 1, vi)(Magnesium)	-	600	-
9, Table 1, vii)(Chromium)	-	600	-
9, Table 1, viii)(Zinc)	-	600	-
9, Table 1, ix)(Titanium)	-	600	-
9, Table 1, x)(Boron)	-	600	-
9, Table 1, xi)(Gallium)	-	600	-
9, Table 1, xii)(Zirconium)	-	600	-
9, Table 1, xiii)(Titanium + Vanadium)	-	1200	-
9, Table 1, xiv)(Other elements (each))	-	1000	-
9, Table 1, xv)(Other elements (Total))	-	0.0	-
8(SHAPES AND SIZES)	-	0	-
9, Table 1, i)(Aluminium, Min)	-	0	-
9, Table 1, ii)(Silicon)	-	0	-
9, Table 1, iii)(Iron)	-	0	-
9, Table 1, iv)(Copper)	-	0	-
9, Table 1, v)(Manganese)	-	0	-
9, Table 1, vi)(Magnesium)	-	0	-
9, Table 1, vii)(Chromium)	-	0	-
9, Table 1, viii)(Zinc)	-	0	-
9, Table 1, ix)(Titanium)	-	0	-
9, Table 1, x)(Boron)	-	0	-
9, Table 1, xi)(Gallium)	-	0	-
9, Table 1, xii)(Zirconium)	-	0	-
9, Table 1, xiii)(Titanium + Vanadium)	-	0	-
9, Table 1, xiv)(Other elements (each))	-	0	-
9, Table 1, xv)(Other elements (Total))	-	0	-

03 Apr, 2027

-
Included w.e.f. 10.06.2024

IS 1180 : Part 3 (2021)

Outdoor/Indoor Type Liquid Immersed Distribution Transformers Up to and Including 2 500 kVA, 33 kV — Specification Part 3 Natural/Synthetic Organic Ester Liquid Immersed

Natural/Synthetic Organic Ester Liquid Immersed

132000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 Table 1(Standard Ratings)	-	0	-
6.2, 7.2, 8.2(Rated Frequency)	-	0	-
6.3, 7.3(Nominal System Voltage)	-	0	-
6.4(Table 2 Minimum Basic Insulation Level)	-	0	-
6.5, 7.5(No-Load Voltage Ratios)	-	0	-
6.6, 7.6(Winding Connections and Phase Displacement)	-	0	-
6.7(Tapping Range and Tapping Methods)	-	0	-
6.8(Table 3 Losses and Impedance Values)	-	0	-
6.9(Permissible Flux Density and Over Fluxing)	-	0	-
6.10(Limits of Temperature-rise)	-	0	-
7.1(Table 4 Standard Ratings)	-	0	-
7.4(Table 5 Minimum Basic Insulation Level)	-	0	-
7.7(Tapping Ranges and Tapping Methods)	-	0	-
7.8(Losses and Impedance Values)	-	0	-
7.9(Permissible Flux Density and Overfluxing)	-	0	-
7.10(Limits of Temperature Rise)	-	0	-
8.1 Table 7(Standard Ratings)	-	0	-
8.3(Nominal System Voltage)	-	0	-
8.5(No Load Voltage Ratio)	-	0	-
8.6(Number of Phases and Polarity)	-	0	-
8.4(Table 8 Minimum Basic Insulation Level)	-	0	-
8.8(Losses and Impedance Values)	-	0	-
8.9(Permissible Flux Density and Overfluxing)	-	0	-
8.10(Limits of Temperature Rise)	-	0	-
9(Standard Materials)	-	0	-
10(Terminal Arrangement)	-	0	-
11(Minimum clearances in air)	-	0	-
12(Connectors (Applicable for bare bushing terminations only))	-	0	-
13(Marking)	-	0	-
14(Mounting Arrangement)	-	0	-
15(Transformer Tank)	-	0	-
16(Conservator for non-sealed typetransformers)	-	0	-
18(Efficiency and regulation)	-	0	-
19(Tolerances)	-	0	-
20(Fittings)	-	0	-
21.2 a(Measurement of winding resistance [IS 2026 (Part 1)].)	-	7000	Complete testing charges Rs. 88000/- for 0 to 100 kVA, Rs. 98100/- for 100kVA to 250kVA, Rs. 104000/- for 250kVA to 630 kVA, Rs. 105100/- for 630kVA to 1000kVA, Rs. 129900/- for 1000kVA to1600kVA, Rs. 132000/- for 1600kVA to 2500kVA
21.2 b(Measurement of voltage ratio and check of phase displacement [IS 2026 (Part 1)].)	-	5500	-
21.2 c(Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load [IS 2026 (Part 1)].)	-	5500	-
21.2 d(Measurement of no-load loss and current [IS 2026 (Part 1)].)	-	3500	-
21.2 e(Measurement of insulation resistance [IS 2026 (Part 1)].)	-	2500	-
21.2 f(Induced over-voltage withstand test [IS 2026 (Part 3)].)	-	4500	-
21.2 g(Separate-source voltage withstand test [IS 2026 (Part 3)])	-	4000	-
21.3 a(Lightning impulse test [IS 2026 (Part 3)].)	-	41000	-
21.3 b(Temperature-rise test [IS 2026 (Part 2)].)	-	24000	-
21.3 d(Pressure test)	-	6000	-
21.4 a(Determination of sound levels [IS 2026 (Part 10)];)	-	8000	-
21.4 c(No load current at 112.5 percent voltage (see 6.9.2, 7.9.2, 8.9.2);)	-	1000	-
21.4 d(Paint adhesion test — The test is performed as per ASTM D3359 (Standard Test Methods for measuring adhesion by tape test).)	-	3000	-
21.4 e(BDV and Moisture content of liquid in the transformer (IS 16081, IS 16099, IS 16899 or IS 16659, whichever is applicable).)	-	2000	-
21.5(Pressure and Ester Liquid Leakage Test)	-	8000	-
4(SERVICE CONDITIONS)	-	0	-
5(General)	-	0	-
6.1(Rating)	-	0	-
6.2(Rated Frequceny)	-	0	-
6.3(Nominal System Voltage)	-	0	-
6.4(Basic Insulation Level)	-	0	-
6.5(No-Load Voltage Ratios)	-	0	-
6.6(Winding connection and phase displacement)	-	0	-
6.7(Tapping range and tapping methods)	-	0	-
6.8(Losses and Impedance Value)	-	0	-
6.9(Permissible flux density and over fluxing)	-	0	-
6.10(Limits of temperature-rise)	-	0	-
7("Technical parameters of three phase distribution transformers higher ")	-	0	-
8(Technical parameter of single phase distribution transformers)	-	0	-
9(Standard Materials)	-	0	-
10(Terminal Arrangement)	-	0	-
11(Minimum clearances in air)	-	0	-
12(Connectors for bare bushing terminations)	-	0	-
13(Marking)	-	0	-
14(Mounting Arrangement)	-	0	-
15(Trasnformer tank)	-	0	-
16(Conservator for non-sealed type transformers)	-	0	-
18(Efficiency and regulations)	-	0	-
19(Tolerances)	-	0	-
20(Fittings)	-	0	-
21.1(General)	-	0	-
21.2(Routine Tests)	-	40500	Routine testing charges Rs. 22600/- for 0 to 100 kVA, Rs. 25700/- for 100kVA to 250kVA, Rs. 28200/- for 250kVA to 630 kVA, Rs. 29100/- for 630kVA to 1000kVA, Rs. 36600/- for 1000kVA to1600kVA, Rs. 40500/- for 1600kVA to 2500kVA
21.3(Types test)	-	132000	-
21.4(Special Test)	-	14000	Additional charges if applicable
21.5(Pressure and Ester Liquid Leakage Test)	-	0	-
22(Information required with enquiry and order)	-	0	-
6.1 Table 1(Standard Ratings)	-	0	-
6.2, 7.2, 8.2(Rated Frequency)	-	0	-
6.3, 7.3(Nominal System Voltage)	-	0	-
6.4(Table 2 Minimum Basic Insulation Level)	-	0	-
6.5, 7.5(No-Load Voltage Ratios)	-	0	-
6.6, 7.6(Winding Connections and Phase Displacement)	-	0	-
6.7(Tapping Range and Tapping Methods)	-	0	-
6.8(Table 3 Losses and Impedance Values)	-	0	-
6.9(Permissible Flux Density and Over Fluxing)	-	0	-
6.10(Limits of Temperature-rise)	-	0	-
7.1(Table 4 Standard Ratings)	-	0	-
7.4(Table 5 Minimum Basic Insulation Level)	-	0	-
7.7(Tapping Ranges and Tapping Methods)	-	0	-
7.8(Losses and Impedance Values)	-	0	-
7.9(Permissible Flux Density and Overfluxing)	-	0	-
7.10(Limits of Temperature Rise)	-	0	-
8.1 Table 7(Standard Ratings)	-	0	-
8.3(Nominal System Voltage)	-	0	-
8.5(No Load Voltage Ratio)	-	0	-
8.6(Number of Phases and Polarity)	-	0	-
8.4(Table 8 Minimum Basic Insulation Level)	-	0	-
8.8(Losses and Impedance Values)	-	0	-
8.9(Permissible Flux Density and Overfluxing)	-	0	-
8.10(Limits of Temperature Rise)	-	0	-
9(Standard Materials)	-	0	-
10(Terminal Arrangement)	-	0	-
11(Minimum clearances in air)	-	0	-
12(Connectors (Applicable for bare bushing terminations only))	-	0	-
13(Marking)	-	0	-
14(Mounting Arrangement)	-	0	-
15(Transformer Tank)	-	0	-
16(Conservator for non-sealed typetransformers)	-	0	-
18(Efficiency and regulation)	-	0	-
19(Tolerances)	-	0	-
20(Fittings)	-	0	-
21.2 a(Measurement of winding resistance [IS 2026 (Part 1)].)	-	7000	Complete testing charges Rs. 88000/- for 0 to 100 kVA, Rs. 98100/- for 100kVA to 250kVA, Rs. 104000/- for 250kVA to 630 kVA, Rs. 105100/- for 630kVA to 1000kVA, Rs. 129900/- for 1000kVA to1600kVA, Rs. 132000/- for 1600kVA to 2500kVA
21.2 b(Measurement of voltage ratio and check of phase displacement [IS 2026 (Part 1)].)	-	5500	-
21.2 c(Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load [IS 2026 (Part 1)].)	-	5500	-
21.2 d(Measurement of no-load loss and current [IS 2026 (Part 1)].)	-	3500	-
21.2 e(Measurement of insulation resistance [IS 2026 (Part 1)].)	-	2500	-
21.2 f(Induced over-voltage withstand test [IS 2026 (Part 3)].)	-	4500	-
21.2 g(Separate-source voltage withstand test [IS 2026 (Part 3)])	-	4000	-
21.3 a(Lightning impulse test [IS 2026 (Part 3)].)	-	41000	-
21.3 b(Temperature-rise test [IS 2026 (Part 2)].)	-	24000	-
21.3 d(Pressure test)	-	6000	-
21.4 a(Determination of sound levels [IS 2026 (Part 10)];)	-	8000	-
21.4 c(No load current at 112.5 percent voltage (see 6.9.2, 7.9.2, 8.9.2);)	-	1000	-
21.4 d(Paint adhesion test — The test is performed as per ASTM D3359 (Standard Test Methods for measuring adhesion by tape test).)	-	3000	-
21.4 e(BDV and Moisture content of liquid in the transformer (IS 16081, IS 16099, IS 16899 or IS 16659, whichever is applicable).)	-	2000	-
21.5(Pressure and Ester Liquid Leakage Test)	-	0	-
4(SERVICE CONDITIONS)	-	0	-
5(General)	-	0	-
6.1(Rating)	-	0	-
6.2(Rated Frequceny)	-	0	-
6.3(Nominal System Voltage)	-	0	-
6.4(Basic Insulation Level)	-	0	-
6.5(No-Load Voltage Ratios)	-	0	-
6.6(Winding connection and phase displacement)	-	0	-
6.7(Tapping range and tapping methods)	-	0	-
6.8(Losses and Impedance Value)	-	0	-
6.9(Permissible flux density and over fluxing)	-	0	-
6.10(Limits of temperature-rise)	-	0	-
7("Technical parameters of three phase distribution transformers higher ")	-	0	-
8(Technical parameter of single phase distribution transformers)	-	0	-
9(Standard Materials)	-	0	-
10(Terminal Arrangement)	-	0	-
11(Minimum clearances in air)	-	0	-
12(Connectors for bare bushing terminations)	-	0	-
13(Marking)	-	0	-
14(Mounting Arrangement)	-	0	-
15(Trasnformer tank)	-	0	-
16(Conservator for non-sealed type transformers)	-	0	-
18(Efficiency and regulations)	-	0	-
19(Tolerances)	-	0	-
20(Fittings)	-	0	-
21.1(General)	-	0	-
21.2(Routine Tests)	-	40500	Routine testing charges Rs. 22600/- for 0 to 100 kVA, Rs. 25700/- for 100kVA to 250kVA, Rs. 28200/- for 250kVA to 630 kVA, Rs. 29100/- for 630kVA to 1000kVA, Rs. 36600/- for 1000kVA to1600kVA, Rs. 40500/- for 1600kVA to 2500kVA
21.3(Types test)	-	132000	-
21.4(Special Test)	-	14000	Additional charges if applicable
21.5(Pressure and Ester Liquid Leakage Test)	-	0	-
22(Information required with enquiry and order)	-	0	-

03 Apr, 2027

-
Included w.e.f 03.05.2024 Exclusion: Cl.17 (Ability of Transformers to withstand external short circuit), Cl. 21.3 c (Short-circuit withstand test [IS 2026 (Part 5)] (up to 200 kVA) and), Cl. 21.4 b (Short-circuit withstand test [IS 2026 (Part 5)] (above 200 kVA);)

IS 398 : Part 6 (2021)

Aluminium Conductors For Overhead Transmission Purposes Part 6: High conductivity aluminium alloy stranded conductors

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2(Visual Examination)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	1500	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	1500	-
16.5, Table 2(Breaking Load Test - before stranding)	-	0	-
16.5, Table 2(Breaking Load Test - after stranding)	-	2000	-
16.6, Table 1(Elongation Test - before stranding)	-	0	-
16.6, Table 1(Elongation Test - after stranding)	-	1500	-
16.7, Table 2(Resistivity Test)	-	1000	-
16.8(Wrapping Test)	-	1000	-
11(Stranding)	-	0	-
8(Freedom from defects)	-	0	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	2500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024 Exclusion: 16.9, Table-3 (Ultimate tensile strength on stranded conductor , Cl.16.11 (Stress- strain test)

IS 398 : Part 5 (1992)

Aluminium conductor for overhead transmission purposes - Specification: Part 5 aluminium conductors - Galvanized steel - Reinforced for extra high voltage (400 KV And Above) (First Revision)

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 (elec)(Freedom from defects)	-	0	-
13.2 (mech)(Visual Examination)	-	0	-
13.3 Table-1 (mech)(Diameter-Aluminium wires)	-	1000	-
13.3 Table-2 (mech)(Diameter-Galvanized Steel wires)	-	500	-
13.5.1 Table 3 (elec)(Breaking Load on Complete conductor)	-	1500	-
13.5.2 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	1500	-
13.5.2 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	0	-
13.5.2 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	0	-
13.5.2 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.6.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.6.1 (mech)(Ductility by Torsion Test after stranding)	-	0	-
13.6.2 (mech)(Ductility by Elongation Test before stranding)	-	1000	-
13.6.2 (mech)(Ductility by Elongation Test after stranding)	-	0	-
13.7.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.7.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	0	-
13.7.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.7.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	0	-
13.8 (elec)(Resistance test-Aluminium wire before Stranding)	-	2000	-
14.8 (elec)(Resistance test-Aluminium wire after stranding)	-	0	-
13.9.2 (chem)(Mass of Zinc coating)	-	1500	-
13.9.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.4 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.4 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.4 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors eith 3 Aluminium Wire Layers)	-	1000	-
13.4 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
10.4 (mech)(Direction of lay)	-	0	-
13.5.2 & Table 2 (mech)(Breaking load of steel wire before stranding)	-	0	-
13.9 (elec)(The test of galvanising)	-	0	-
8.2.1 (elec)(Size of complete conductor)	-	0	-
8.2.2 (elec)(Resistance of complete conductor)	-	0	-
10.4 (elec)(Direction of lay)	-	0	-
13.5.2 & Table 2 (elec)(Breaking load of steel wire before stranding)	-	0	-
13.4 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	0	-
13.4 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	0	-
13.4 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors eith 3 Aluminium Wire Layers)	-	0	-
13.4 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.9.2 (elec)(Uniformity of Zinc coating)	-	0	-
13.9.2 (elec)(Mass of Zinc coating)	-	0	-
13.7.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	0	-
13.7.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	0	-
13.7.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	0	-
13.7.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	0	-
13.6.2 (elec)(Ductility by Elongation Test after stranding)	-	0	-
13.6.2 (elec)(Ductility by Elongation Test before stranding)	-	0	-
13.6.1 (elec)(Ductility by Torsion Test after stranding)	-	0	-
13.6.1 (elec)(Ductility by Torsion Test before stranding)	-	0	-
13.5.2 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.5.2 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	0	-
13.5.2 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	0	-
13.5.2 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	0	-
13.3 Table-2 (elec)(Diameter-Galvanized Steel wires)	-	0	-
13.3 Table-1 (elec)(Diameter-Aluminium wires)	-	0	-
13.2 (elec)(Visual Examination)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024 Exclusion: Cl.13.10 (Surface condition test), Cl.13.11 (Corona Test), Cl.13.12 ( Radio Interference voltage test)

IS 398 : Part 3 (1976)

Specification for aluminium conductors for overhead transmission purposes: Part 3 aluminium conductors, aluminized steel reinforced (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.2 Table 3(Resistance test-Aluminium wire Calculated Resistance)	-	1000	-
12.5 Table 1(Resistance test-Aluminium wire after stranding)	-	1500	-
12.5 Table 1(Resistance test-Aluminium wire before Stranding)	-	0	-
12.4.2(Wrapping TestAluminized Steel Wires After Stranding)	-	1500	-
12.4.2(Wrapping Test Aluminized Steel Wires Before Stranding)	-	0	-
12.4.1(Wrapping Test Aluminium Wires After Stranding)	-	1500	-
12.4.1(Wrapping Test Aluminium Wires Before Stranding)	-	0	-
12.3.2(Ductility by Elongation Test after stranding)	-	1000	-
12.3.2(Ductility by Elongation Test before stranding)	-	0	-
12.3.1(Ductility by Torsion Test after stranding)	-	1000	-
12.3.1(Ductility by Torsion Test after stranding)	-	0	-
12.3.1(Ductility by Torsion Test before stranding)	-	0	-
12.3.1(Ductility by Torsion Test before stranding)	-	0	-
12.2 Table 2(Breaking Load of aluminized steel wires After Stranding)	-	2500	-
12.2 Table 1(Breaking Load of Aluminium Wires After Stranding)	-	1500	-
12.2 Table 2(Breaking Load of aluminized steel wires Before Stranding)	-	0	-
12.2 Table 1(Breaking Load of Aluminium Wires Before Stranding)	-	0	-
9.5(STRANDING)	-	0	-
9.4(STRANDING)	-	0	-
9.3 Table 4(STRANDING)	-	0	-
9.2 Table 4(STRANDING : Lay Ratio For Steel Core)	-	1000	-
9.2 Table 4(STRANDING : Lay Ratio For Aluminium Wire)	-	1000	-
9.2 Table 4(STRANDING : Lay Ratio For Aluminium Wire)	-	0	-
9.2 Table 4(STRANDING : Lay Ratio For Aluminium Wire)	-	0	-
8.2(JOINTS IN WIRES : Aluminized Steel Wires)	-	0	-
8.1(JOINTS IN WIRES : Aluminium Wires)	-	0	-
7.1.2.2 Table 2(Diameter of Alumized Steel Wires After Stranding)	-	500	-
7.1.2.1 Table-1(Diameter of Aluminium Wires After Stranding)	-	1000	-
7.1.2.2 Table 2(Diameter of Alumized Steel Wires Before Stranding)	-	0	-
7.1.2.1 Table-1(Diameter of Aluminium Wires Before Stranding)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024 Exclusion: Cl.12.6 (Aluminizing Test)

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	750	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	750	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	750	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	750	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (mech)(Stranding)	-	0	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	1500	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	500	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1500	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	500	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	250	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	250	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	250	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	250	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	250	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	250	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	1500	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	1500	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1500	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1500	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	2500	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	2500	-
13.7.2 (chem)(Mass of Zinc coating)	-	1000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	750	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	0	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	0	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	0	-
13.7.2 (elec)(Mass of Zinc coating)	-	0	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	0	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	0	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1500	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1500	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	2500	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	2500	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	2500	10% discount to BIS
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	2500	10% discount to BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	0	10% discount to BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1500	10% discount to BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1500	10% discount to BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1500	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	0	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	0	-
13.7.2 (elec)(Mass of Zinc coating)	-	0	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1500	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1500	10% discount to BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	0	10% discount to BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1500	10% discount to BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	10% discount to BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	10% discount to BIS
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	10% discount to BIS
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	0	10% discount to BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	2500	10% discount to BIS
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	2500	10% discount to BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	2500	10% discount to BIS
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	2500	10% discount to BIS
10 (elec)(Stranding)	-	0	10% discount to BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1500	10% discount to BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1500	10% discount to BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1500	10% discount to BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1500	10% discount to BIS
4.1(Resistivity)	-	0	-
4.2(Density)	-	0	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	0	-
4.4(Coefficient of Linear Expansion)	-	0	-
5.1(Density)	-	0	-
5.2(Coefficient of Linear Expansion)	-	0	-
14.2(a), 8.2.1(Sizes)	-	0	-
7(FREEDOM FROM DEFECTS)	-	0	-
6.2(zinc Purity)	-	0	-
9(Joint in wires)	-	0	-
13.10 (elec)(Ultimate breaking load)	-	0	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	-	-
10 (elec)(Stranding)	-	-	-
10 (elec)(Stranding)	-	-	-
10 (elec)(Stranding)	-	-	-
10 (mech)(Stranding)	-	-	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	-	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	-	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	-	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	-	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	-	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	-	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	-	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	-	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	-	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	-	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	-	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	-	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	-	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	-	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	-	-
13.7.2 (chem)(Mass of Zinc coating)	-	-	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	-	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	-	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	-	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	-	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	-	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	-	-
13.7.2 (elec)(Mass of Zinc coating)	-	-	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	-	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	-	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	-	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	-	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	-	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	-	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	-	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	-	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	-	-
13.7.2 (elec)(Mass of Zinc coating)	-	-	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	-	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	-	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	-	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	-	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	-	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	-	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	-	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	-	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	-	-
10 (elec)(Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	-	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	-	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	-	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	-	-
4.1(Resistivity)	-	-	-
4.2(Density)	-	-	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	-	-
4.4(Coefficient of Linear Expansion)	-	-	-
5.1(Density)	-	-	-
5.2(Coefficient of Linear Expansion)	-	-	-
14.2(a), 8.2.1(Sizes)	-	-	-
7(FREEDOM FROM DEFECTS)	-	-	-
6.2(zinc Purity)	-	-	-
9(Joint in wires)	-	-	-
13.10 (elec)(Ultimate breaking load)	-	-	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024 Exclusion: Cl.13.9 (Surface condition test), Cl.13.10 (Ultimate breaking load), Cl.13.11 (Stress-Strain test)

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

8100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	1000	-
Cl 9(Tensile Test On UTM)	-	1000	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
6 AND AS PER IS 7887(MICRO ALLOY)	-	0	-
6 AND AS PER IS 7887(ALUMINIUM)	-	500	-
6 AND AS PER IS 7887(PHOSPHORUS)	-	600	-
6 AND AS PER IS 7887(SULPHUR)	-	600	-
6 AND AS PER IS 7887(MANGANESE)	-	600	-
6 AND AS PER IS 7887(SILICON)	-	600	-
6 AND AS PER IS 7887(CARBON)	-	600	-
7 & 8(Ovality)	-	600	-
7 & 8(Diameter)	-	600	-
9.2(Wrapping Test)	-	500	-
9.3(Bend test)	-	500	-
10(Finish)	-	0	-
11(Coating test)	-	0	-
13(Freedom from defects)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
14(Packing)	-	0	-
15(Marking)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	1500	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	3500	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	1500	-
9.3(Direction of Lay)	-	0	-
9.4(Multiple layers of wires)	-	1500	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	2500	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	2500	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	0	-
9.2(Lay Ratio 24 wire layer)	-	0	-
9.2(Lay Ratio 18 wire layer)	-	0	-
9.2(Lay Ratio 12 wire layer)	-	0	-
9.2(Lay Ratio 3/6 wire layer)	-	0	-
7.2.1(Sizes)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	1500	-
12.3, Table-1(Breaking load before stranding)	-	2500	-
12.3, Table-1(Breaking load after stranding)	-	2500	-
12.4(Wrapping test)	-	1500	-
12.5, Table 1(Resistance test)	-	3500	-
12.6, Table 3(Measurement of lay ratio)	-	1500	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
7.2.1(Sizes)	-	0	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	0	-
9.2(Lay ratio)	-	1500	-
9.4(Multiple layer of wires)	-	1500	-
4.2(Density)	-	0	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	0	-
4.4(Coefficient of Linear Expansion)	-	0	-
5(Material)	-	0	-
7.1.1(Nominal Sizes)	-	0	-
7.2.2(Resistance)	-	0	-
4.1(Resistivity)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

13050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	0	-
6.1(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	0	-
6.1(a) Reference to this Indian Standard;)	-	0	-
6.1(b) Manufacturer's name,brand name or trade-mark;)	-	0	-
6.1(c) Size of conductor / maximum overall diameter,)	-	0	-
6.1(d) Length of conductor on spool / reel /coil;)	-	0	-
6.1(e) Number of lengths onspool / reel / coil (if more than one);)	-	0	-
6.1(f) Country of Manufacturer)	-	0	-
6.1(g) Year of Manufacture.)	-	0	-
6.2(BIS Certification Mark)	-	0	-
4(i) Material)	-	0	-
5(ii) Diameter [mm] Seperate wire:)	-	500	-
5(ii) Diameter [mm] Wire taken from cable:)	-	0	-
5(iii) Annealing test [Percentage] on Seperate wire:)	-	1000	-
5(iii) Annealing test [Percentage] on Wire taken from cable:)	-	0	-
5(d) Resistance test [Ohm/km corrected to 20°c)	-	1000	-
4.1, table 1 & 2(a) Thickness of Polyster (mm))	-	500	-
4.1, table 1 & 3(b) Thickness of Polypropylene (mm))	-	0	-
4.1, table 1 & 4(c) Total thickness of Insulation(mm))	-	500	-
4.2(Application of insulation)	-	0	-
4.3(Colour of Insuation)	-	0	-
4.4(Overall diameter (mm))	-	500	-
4(Before ageing Tensile strength [N/mm²])	-	1500	-
4(Before ageing Elongation at break [Percentage])	-	0	-
4(After ageing Tensile strength [N/mm²])	-	2500	-
4(Variation on tensile strangth [Percentage])	-	0	-
4(After ageing Elongation at break [Percentage])	-	0	-
4(Variation on elongation at break [Percentage])	-	0	-
4(Shrinkage test [Percentage])	-	1500	-
4(After Shrinkage Cracks found.)	-	0	-
4.1(Water absorption test [Gravimetric] [mg/cm²])	-	4500	-
4.1(Hot Deformation test [depth of indentation) [Percentage])	-	1500	-
4.1(Heat Shock Test - No cracks found)	-	1500	-
4.5(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	2500	-
4.1(Insulation Resistance test [ohm-cm] At 27 ºC)	-	1500	-
4.1([Insulation Resistance test [ohm-cm] At 90 ºC)	-	0	-
5(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	0	-
6(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	0	-
6(a) Reference to this Indian Standard;)	-	0	-
6(b) Manufacturer's name,brand name or trade-mark;)	-	0	-
6(c) Size of conductor / maximum overall diameter,)	-	0	-
6(d) Length of conductor on spool / reel /coil;)	-	0	-
6(e) Number of lengths onspool / reel / coil (if more than one);)	-	0	-
6(f) Country of Manufacturer Marking)	-	0	-
6(g) Year of Manufacture.)	-	0	-
6.2(BIS Certification Mark)	-	0	-
4(i) Material)	-	0	-
4(ii) Diameter [mm] Seperate wire:)	-	0	-
4(ii) Diameter [mm] Wire taken from cable)	-	0	-
4(iii) Annealing test [Percentage] on Seperate wire:)	-	0	-
4([iii) Annealing test [Percentage] on Wire taken from cable:)	-	0	-
4(d) Resistance test [Ohm/km corrected to 20°c])	-	0	-
4(a) Thickness of Polyster (mm))	-	0	-
4(b) Thickness of Polypropylene (mm))	-	0	-
4(c) Total thickness of Insulation(mm))	-	0	-
4(Application of insulation)	-	0	-
4(Colour of Insuation)	-	0	-
4(Overall diameter (mm))	-	0	-
4(Before ageing Tensile strength [N/mm²])	-	0	-
4(Before ageing Elongation at break [Percentage])	-	0	-
4(After ageing Tensile strength [N/mm²])	-	0	-
4(Variation on tensile strangth [Percentage])	-	0	-
4(After ageing Elongation at break [Percentage])	-	0	-
4(Variation on elongation at break [Percentage])	-	0	-
4(Shrinkage test [Percentage])	-	0	-
4(After Shrinkage Cracks found.)	-	0	-
4(Water absorption test [Gravimetric] [mg/cm²])	-	0	-
4(Hot Deformation test [depth of indentation) [Percentage])	-	0	-
4(Heat Shock Test - No cracks found Physical)	-	0	-
4(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	0	-
4(Insulation Resistance test [ohm-cm] At 27 ºC)	-	0	-
4(Insulation Resistance test [ohm-cm] At 90 ºC)	-	0	-
Clause No. 3(Insulation Resistance (Volume Resistivity at test temperature 90 º C ))	-	0	-
Clause No. 3(Water absorption)	-	0	-
Clause No. 3(Hot Deformation)	-	0	-
Clause No. 3(Shrinkage)	-	0	-
Clause No. 3(Heat Shock)	-	0	-
Clause No. 3(Thickness of Insulation)	-	0	-
Clause No. 3(Annealing Test)	-	0	-
Clause No. 3(Conductor Diameter)	-	500	-
Clause No. 3(Overall Dimensions)	-	0	-
Clause No. 3(Insulation Resistance (Volume Resistivity at 27º C ))	-	0	-
Clause No. 3(High Voltage Test (Water Immersion test) at room temperature)	-	0	-
Clause No. 3(Conductor Resistance)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 8783 : Part 4 : Sec 2 (1995)

Winding wires for submersible motors - specification: Part 4 specification for individual wires: Sec 2 crosslinked polyethylene insulated and polyamide jacketed wires (First Revision)

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Thickness of insulation)	-	500	-
4.2(Application of insulation and jacket)	-	0	-
4.3(Colour)	-	0	-
4.4(Overall diameter)	-	500	-
4.5(The overall surface of finished winding wire)	-	0	-
4.6(High voltage test)	-	2500	-
Table 1, Cl.4.1, Cl.4.4(Cross sectional area)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Conductor diameter)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Thickness of insulation)	-	500	-
Table 1, Cl.4.1, Cl.4.4(Thickness of PA jacket)	-	0	-
Table 1, Cl.4.1, Cl.4.4(Overall diameter)	-	500	-
Table 2, Cl.4.1,Cl.4.4(Conductor cross sectional area)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Conductor composition No. of strands/Strand diameter)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Conductor diameter)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Thickness of insulation)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Thickness of PA jacket)	-	0	-
Table 2, Cl.4.1, Cl.4.4(Overall diameter)	-	0	-
4.6(High Voltage Test (Water Immersion ) )	-	2500	-
4.5( Finish)	-	0	-
4.4(Overall Diameter)	-	0	-
4.3(Insulation : Colour)	-	0	-
4.2(Insulation : Application)	-	0	-
4.1(Insulation : Thickness)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Heat shock Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Hot deformation Test )	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Water absorption)	-	4500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Shrinkage Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Shrinkage Test)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Elongation Variation)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) After Ageing Elongation Test)	-	3000	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Tensile strength Variation)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) After Ageing Tensile strength)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Befor Ageing Elongation Test)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Befor Ageing Tensile strength)	-	0	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Volume resistivity@ 85 °C)	-	1500	-
3.2(Requirements(Cl. 4 Table 1 of IS: 8783 (part 2) Volume resistivity@Room Temprature )	-	0	-
3.2(Dielectric Material )	-	0	-
3.1(Visual examination (Cl 4.1.2 of IS:8783 (Part I):95 )	-	0	-
3.1(Resistance Test ((Cl 6 of IS:8783(Part I):95 )	-	1000	-
3.1(Annealing Test(Cl. 6 of IS:8783(Part I):95 )	-	1000	-
3.1(Dimensions (Cl.5.1.1 of IS:8783 (Part I):95 )	-	500	-
3.1(Conductor (Cl.3.1 ) : ) Material (Cl.4 of IS:8783 (Part I):95 )	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

13950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3.1 (Conductor)	-	0	-
Cl.4(Material)	-	0	-
Cl.5.1.1 (Dimensions)	-	0	-
Cl. 6(Annealing Test)	-	1000	-
Cl 6(Resistance Test)	-	1000	-
Cl 4.1.2 (Visual examination)	-	0	-
Cl.3.2(Dielectric Material )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	1500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	0	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-	15	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-	1500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-	1500	-
Cl.4.1(Insulation )	-	0	-
Cl.4.2(Application)	-	0	-
Cl.4.3(Colour)	-	0	-
Cl.4.4(Overall Diameter)	-	500	-
Cl.4.5(Finish)	-	0	-
Cl.4.6(High Voltage Test Water Immersion )	-	2500	-
Cl No. 3.1(Conductor diameter)	-	500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 4289 : Part 1 (1984)

Specification for flexible cables for lifts and other flexible connections: Part 1 elastomer insulated cables (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Conductor)	-	0	-
4(Separator)	-	0	-
5(Insulation)	-	0	-
5(Central heart)	-	0	-
7(Fillers)	-	0	-
8(Proofed tape)	-	0	-
9(Braid)	-	0	-
10(Sheath)	-	0	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
12(Conductor)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	1000	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	1000	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	3500	-
17.1.f.4(Tear resistance)	-	3500	-
17.1.g(High voltage water immersion test)	-	1000	-
17.1.h(Insulation resistance test)	-	1500	-
17.1.j(Static flexibility test)	-	4800	-
17.1.k(Flammability test)	-	3000	-
17.1.a(Persulphate test)	-	1000	-
17.1.b(Annealing test)	-	1200	-
17.1.c(Conductor resistance test)	-	1000	-
17.1.d(Test for thickness of insulation and sheath)	-	1000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	1000	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	1000	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	1000	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	3500	-
13(Insulation)	-	0	-
14(Core identification)	-	0	-
15(Core assembly)	-	0	-
16.1(Overall covering- sheathed cables)	-	0	-
16.2(overall covering- braided cables)	-	0	-
17.1.a(Persulphate test)	-	1000	-
17.1.b(Annealing test)	-	1200	-
17.1.c(Conductor resistance test)	-	1000	-
17.1.d(Test for thickness of insulation and sheath)	-	1000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	1000	-
17.1.f.4(Tear resistance)	-	3500	-
17.1.g(High voltage water immersion test)	-	1000	-
17.1.h(Insulation resistance test)	-	1500	-
17.1.j(Static flexibility test)	-	4800	-
17.1.k(Flammability test)	-	3000	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
3(Conductor)	-	0	-
4(Separator)	-	0	-
5(Insulation)	-	0	-
5(Central heart)	-	0	-
7(Fillers)	-	0	-
8(Proofed tape)	-	0	-
9(Braid)	-	0	-
10(Sheath)	-	0	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
12(Conductor)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
13(Insulation)	-	0	-
14(Core identification)	-	0	-
15(Core assembly)	-	0	-
16.1(Overall covering- sheathed cables)	-	0	-
16.2(overall covering- braided cables)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-
17.1.a(IS 10810 Part-4)	-	0	-
17.1.b(IS 10810 Part-1)	-	0	-
17.1.c(IS 10810 Part-5)	-	0	-
17.1.d(IS 10810 Part-6)	-	0	-
17.1.e.1(IS 10810 Part-7)	-	0	-
17.1.f.1(IS 10810 Part-7)	-	0	-
17.1.e.2(IS 10810 Part-11)	-	0	-
17.1.e.3(IS 10810 Part-56)	-	0	-
17.1.f.2(IS 10810 Part-56)	-	0	-
17.1.f.3(IS 10810 Part-31)	-	0	-
17.1.f.4(IS 10810 Part-17)	-	0	-
17.1.g(IS 10810 Part-45)	-	0	-
17.1.h(IS 10810 Part-43)	-	0	-
17.1.j(IS 10810 Part-54)	-	0	-
17.1.k(IS 10810 Part-53)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 9857 (1990)

Welding cables - Specification (First Revision)

CABLE

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	0	-
5(SEPARATOR)	-	0	-
6(COVERING)	-	0	-
7(CONDUCTOR : CONSTRUCTION )	-	0	-
8(S E P A R A T O R)	-	0	-
9.1(C O V E R I N G : Application )	-	0	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	0	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	0	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	0	-
9.5(Colour of C o v e r i n g)	-	0	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	500	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	500	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	500	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	1000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	0	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	0	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	0	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	1500	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	0	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	1500	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	0	-
10.1 c) 5)(Hot set test )	-	500	-
10.1 c) 5)(Permanent set )	-	0	-
11.1(High Voltage Test ( Water Immersion Test ))	-	1000	-
11.2(Spark Test)	-	0	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-
12.3(Cable Code)	-	0	-
13.1(Packing )	-	0	-
13.2(Marking)	-	0	-
14(CABLE RATINGS)	-	0	-
15(VOLTAGE DROP)	-	0	-
Table 4(Copper purity test)	-	2500	-
Table 2(Oil resistance - Elongation)	-	0	-
Table 2(Oil resistance - Tensile strength )	-	1500	-
Table 2(Ageing in air bomb - Elongation)	-	0	-
Table 2(Ageing in air bomb - Tensile strength )	-	0	-
Table 1 (Thickness of covering)	-	0	if applicable
15.1 (d)(Heat Shock Test)	-	0	if applicable
15.1 (d)(Hot Deformation Test)	-	0	if applicable
15.1 (d)(Loss Of Mass Test)	-	0	if applicable
10.1(b), Table 1(Thickness of covering)	-	0	if applicable

03 Apr, 2027

-
-

IS 4289 : Part 2 (2000)

Flexible cables for lifts and other flexible connections - Specification: Part 2 pvc insulated circular cables

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor)	-	0	-
5(Separator)	-	0	-
6(Insulation)	-	0	-
7(Central heart)	-	0	-
8(Fillers)	-	0	-
9(tape)	-	0	-
10(braid)	-	0	-
11(sheath)	-	0	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
13(Construction- Conductor)	-	0	-
14(Construction- Insulation)	-	0	-
14.2(Thickness of Insulation)	-	1000	-
14.3(Tolerance on Thickness of Insulation)	-	0	-
15(Core identification)	-	0	-
16(Core assembly)	-	0	-
17(overall covering)	-	0	-
17.1.1(Thickness of Sheath)	-	1000	-
17.1.2(Tolerance on Thickness of Sheath)	-	0	-
18.1.a.i(IS 10810 Part-1)	-	1500	-
18.1.a.ii(IS 10810 Part-5)	-	1000	-
18.1.b(IS 10810 Part-6)	-	1000	-
18.1.c.i(IS 10810 Part-7)	-	1000	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	1000	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	3500	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	1500	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	1500	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	1000	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.d(IS 10810 Part-45)	-	1000	-
18.1.e(IS 10810 Part-43)	-	1000	-
18.1. f(IS 10810 Part-54)	-	4500	-
18.1.g(IS 10810 Part-53)	-	3000	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

4050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14 (a)(Marking)	-	0	-
14 (b)(Marking)	-	0	-
14 (c)(Marking)	-	0	-
14 (d)(Marking)	-	0	-
14 (e)(Marking)	-	0	-
14 (f)(Marking)	-	0	-
14 (g)(Marking)	-	0	-
14.2(Marking)	-	0	-
7(Dimensions)	-	500	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
11(Freedom from defects)	-	0	-
9.1(Galvanizing Requirements )	-	2500	-
9.2(Galvanizing Requirements )	-	0	-
9.3(Galvanizing Requirements )	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	1500	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.2(Mechanical Properties (as per IS 1717))	-	0	-
8.3(Mechanical Properties (as per IS 1755))	-	0	-
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	0	-
14(Marking)	-	0	-
14 (a)(Marking)	-	0	-
14 (b)(Marking)	-	0	-
14 (c)(Marking)	-	0	-
14 (d)(Marking)	-	0	-
14 (e)(Marking)	-	0	-
14 (f)(Marking)	-	0	-
14 (g)(Marking)	-	0	-
14.2(Marking)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
7(Dimensions)	-	0	-
11(Freedom from defects)	-	0	-
9.1(Galvanizing Requirements )	-	0	-
9.2(Galvanizing Requirements )	-	0	-
9.3(Galvanizing Requirements )	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	0	-
8.2(Mechanical Properties (as per IS 1717))	-	0	-
8.3(Mechanical Properties (as per IS 1755))	-	0	-
8.4(Mechanical Properties (as perIS 10810(Part- 42)))	-	0	-
Clause 6.1, Table-1(Sulphur)	-	100	-
Clause 6.1, Table-1(Phosphorus)	-	100	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	100	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	0	-
6.2(Phosphorus %)	-	0	-
6.2(Sulphur %)	-	0	-
6.2( Nitrogen%)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

Bureau of Indian Standards

The National Standards Body of India

RTRC LIMITED, GURUGRAM

Plot No. 296, Sector-7, Phase-II,Industrial Estate,IMT Manesar, Gurugram, Gurugram, Gurugram, Haryana, 122050

8826495200 qa@rtrc.in

Scope List