BIS - LIMS (Laboratory Information Management System)

Plastics Woven Bag Testing Lab-Technical Training & Research Centre - TTRC

Technical Training and Research Centre, Grand Trunk Road, Choubepur Kalan, Kanpur Nagar, Uttar Pradesh 209203, Kanpur, Kanpur Nagar, Uttar Pradesh, 209203

9935094562 Jitendra.arya@lohiagroup.com

Scope List

Reset

5 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

50 kg

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.6(Drop Impact Test)	-	500	-
4.1(Raw Meterial)	-	200	-
4.2("Fabric a) Width of Tape")	-	0	-
4.2("Fabric b) Linear Density")	-	0	-
4.2("Fabric c) Mesh")	-	200	-
4.2("Fabric c) Mesh")	-	200	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	500	-
4.3(Sacks)	-	0	-
4.4.1(Loose Liner)	-	0	-
4.4.1(Thickness of Linear)	-	0	-
4.4.2(Visual Observation)	-	200	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.5(Mass of The Lamination)	-	0	-
4.5(Laminated Fabric)	-	0	-
4.5(Lamination Over Hang of the fabric after trimming)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	8500	-
4.6.2(Breaking Load for UV Stabilized sack)	-	8500	-
4.7(Mouth of the Sack)	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	200	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	500	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	500	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	500	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	1000	-
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	1000	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	200	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	200	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	800	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	800	-
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	0	-
Cl. No.5.2(Visual Observation)	-	200	-
Cl. No.5.3(Mass of Bale)	-	0	-
Cl. No.5.4(Breaking Strength of Fabric)	-	1000	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	800	-
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	800	-
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	800	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	-
Cl. No.5.7(UV Resistance)	-	1000	-
Cl. No.6.1(Printing on Sacks)	-	0	-
Cl. No.6.2.(Packaging)	-	0	-
Cl. No.6.3.(Marking on the Bale)	-	0	-
Cl. No.6.4.(BIS Certification Marking)	-	0	-
Cl. No.6.5.(Storage)	-	0	-

29 Jul, 2028

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

10 kg, 15 kg, 20 kg, 25 kg and 30 kg

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(The number of stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	200	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	200	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v(Mass of sack )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1000	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1000	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	750	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	200	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	200	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8500	-
5.2 and Table 1 x(Ash content )	-	800	-
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(The number of stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	200	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	200	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v(Mass of sack )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1000	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1000	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	750	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	200	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	200	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8500	-
5.2 and Table 1 x(Ash content )	-	800	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	1000	-

29 Jul, 2028

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

50/25

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Liner IS 10146 or IS 10910.)	-	0	-
4.4(Mass of the loose liner )	-	0	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.4.1(Liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	200	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	200	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1000	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1000	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	750	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	200	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	200	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8000	-
5.2 and Table 1 x(Ash content )	-	800	-
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Liner IS 10146 or IS 10910.)	-	0	-
4.4(Mass of the loose liner )	-	200	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.4.1(Liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	200	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	200	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1000	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1000	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	800	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	200	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	200	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8000	-
5.2 and Table 1 x(Ash content )	-	800	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	1000	-
Cl-4.4 (Amendment-3)(Thickness of liner)	-	200	-
5.3(UV Resistance)	-	5500	-

29 Jul, 2028

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	500	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.3.1(Bottom seam (IS 10789))	-	0	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1000	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	750	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	200	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8500	-
4.2 and Table 1 x(Ash content )	-	800	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	200	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	500	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.3.1(Bottom seam (IS 10789))	-	800	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1000	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	800	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	200	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	8500	-
4.2 and Table 1 x(Ash content )	-	800	-
3.1(Material Identification)	-	1000	-
3.1(Overall Migration)	-	0	-
3.2(Density)	-	0	-
3.2(MFI)	-	1000	-
Cl 3.2 (Weight in g/m2) (Amendment 3)(Weight in g/m2)	-	200	-
Cl 3.2 (Mesh size)(Mesh size)	-	200	-
3.3.2(Mouth)	-	200	-

29 Jul, 2028

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	200	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	200	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	200	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	200	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	200	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	750	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	500	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	750	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	750	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	1000	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	750	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	800	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	800	-
5/5.6 (UV Resistance, )	-	8500	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	200	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	200	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	200	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	200	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1000	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	750	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	800	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	800	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	8500	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	200	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	850	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	1000	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	1000	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	750	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1000	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	1000	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	8500	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Cl-5 Fig. 1- Table 1- Sr. no. ii(Ends per dm - Annex B 40 ± 2)	-	0	-
Cl-5 Fig. 1- Table 1-Sr. no. iii(Picks per dm-Annex B 40 ± 2)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm)	-	0	-
Cl-5, Fig. 1- Table 1-Sr. no. i(Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm)	-	0	-
Cl-5, Fig. 1, Table 1(i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm)	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1000	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	850	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	750	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	800	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	800	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	8500	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-

29 Jul, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Plastics Woven Bag Testing Lab-Technical Training & Research Centre - TTRC

Technical Training and Research Centre, Grand Trunk Road, Choubepur Kalan, Kanpur Nagar, Uttar Pradesh 209203, Kanpur, Kanpur Nagar, Uttar Pradesh, 209203

9935094562 Jitendra.arya@lohiagroup.com

Scope List