BIS - LIMS (Laboratory Information Management System)

CIPET, Lucknow

B-27 Amausi Industrial Area Nadarganj Lucknow, Luknow, Lucknow, Uttar Pradesh, 226008

7052009477 cipetlko2@gmail.com

Scope List

Reset

55 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

16731.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	500	-
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	750	-
5.1.6(Ash content - IS 2508: 2024)	-	1200	-
5.1.6(carbon black dispersion - IS 2530: 1963)	-	500	-
5.1.1(Appearance)	-	500	-
5.1.2(Film Form)	-	500	-
5.1.3(Odour)	-	500	-
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	1100	-
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	500	-
5.2.1.2(Nominal Width)	-	500	-
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	-
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	-
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4200	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	-
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	850	-
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1600	-
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1600	-
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	-
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	-
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4200	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	-
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	850	-
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	-
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1300	-
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	-
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	-
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1600	-
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	1100	-
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	-
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1300	-
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1300	-
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1300	-
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	-
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	-
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	0	-
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	1300	-
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1600	-

31 Dec, 2026

-
Included w.e.f 16.06.2025

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

42700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	700	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	850	-
7.3( Opacity)	-	700	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	1000	-
8.2 table-9( Pipe Ends)	-	500	-
5 / 5.1(MATERIALS )	-	2000	-
5.3(VCM Content)	-	3000	-
5.4( K-Value)	-	1100	-
5.6 / 5.6.1( Material Classification, table -1)	-	500	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	500	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	500	-
7.2( Colour)	-	500	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	500	-
8.1.2, table 4 to 7(Wall Thickness)	-	500	-
8.1.3 (Length, meter)	-	500	-
8.2 table-9(Dimensions of Integral Socket)	-	500	-
9.3 table-12( Ring Stiffness)	-	1600	-
9.4, annexure-E( Orientation Factor)	-	1200	-
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	500	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	1000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	1000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	1000	-
12(a)( ELASTOMERIC SEALS)	-	2000	-
12(b)( ELASTOMERIC SEALS)	-	1050	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	1100	-
Cl.10, Table 10/2(Effect on Water)	-	3000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	1000	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	1300	-

31 Dec, 2026

-
Included w.e.f.26.05.2025

IS 13664 (1993)

Poly - Pallets for bag storage godowns - Specification

A, B, C, D

15525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.5(End Plugs)	-	500	-
5.1 (Table-1)(Nominal Assembly Dimensions)	-	500	-
5.3(Dimensions and Cross Sectional Details of Members)	-	500	-
7(Material Identification)	-	2000	-
8.1(Type)	-	500	-
8.2(Stability)	-	500	-
8.3(Assembly)	-	500	-
8.4(Fastening)	-	500	-
8.6(Weight)	-	500	-
9.1.1 Table-2(Axial Crushing load)	-	1100	-
9.1.1 Table-2(Cross Sectional crushing load)	-	1100	-
9.1.1 Table-2(Ultimate bending load)	-	1100	-
9.1.2 Table-3(Shear Strength)	-	1100	-
9.1.2 Table-3(Ultimate tensile strength & Elongation)	-	1100	-
9.1.2 Table-3(Impact Strength)	-	1100	-
9.1.2 Table-3(Thermal Stability)	-	1300	-
9.1.2 Table-3(Water absorpation)	-	1100	-
9.1.2 Table-3(Chemical Resistance)	-	1600	-
9.1.2 Table-3(Bent Strength at yield)	-	1100	-
9.1.2 Table-3(Compressive strength at 10% deformation)	-	1100	-
9.1.3.1(Stacking Test)	-	1100	-
9.1.3.1(Bending Test)	-	1100	-
9.1.3.1(Corner Drop Test)	-	1100	-
8.5(End Plugs)	-	500	-
5.1 (Table-1)(Nominal Assembly Dimensions)	-	500	-
5.3(Dimensions and Cross Sectional Details of Members)	-	500	-
7(Material Identification)	-	2000	-
8.1(Type)	-	500	-
8.2(Stability)	-	500	-
8.3(Assembly)	-	500	-
8.4(Fastening)	-	500	-
8.6(Weight)	-	500	-
9.1.1 Table-2(Axial Crushing load)	-	1100	-
9.1.1 Table-2(Cross Sectional crushing load)	-	1100	-
9.1.1 Table-2(Ultimate bending load)	-	1100	-
9.1.2 Table-3(Shear Strength)	-	1100	-
9.1.2 Table-3(Ultimate tensile strength & Elongation)	-	1100	-
9.1.2 Table-3(Impact Strength)	-	1100	-
9.1.2 Table-3(Thermal Stability)	-	1300	-
9.1.2 Table-3(Water absorpation)	-	1100	-
9.1.2 Table-3(Chemical Resistance)	-	1600	-
9.1.2 Table-3(Bent Strength at yield)	-	1600	-
9.1.2 Table-3(Compressive strength at 10% deformation)	-	1600	-
9.1.3.1(Stacking Test)	-	1100	-
9.1.3.1(Bending Test)	-	1100	-
9.1.3.1(Corner Drop Test)	-	1100	-

31 Dec, 2026

-
Included w.e.f.13.05.2025

IS 13217 (1991)

Thermoplastics fumigation covers

22950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Type Tests)	-	500	-
4.1.2(Acceptance Tests)	-	500	-
5.1(Material)	-	2000	-
5.2(Workmanship)	-	500	-
5.3(Subtance)	-	500	-
5.4(Mass of the cover)	-	500	-
5.5(Fumigation Retention Test)	-	6000	5000 + 1000
5.6(Accelerated Ageing Test)	-	4200	-
5.7(Water Proofness Test)	-	1000	-
5.8(Strength of Joints)	-	1100	-
5.9(Blocking Test)	-	1100	-
5.1(Flex Test)	-	1500	-
5.11(Construction of Fumigation Covers ( for Type 1 and Type 2 ))	-	500	-
5.12 Table - 1 (i) (a)(Tensile strength kg/cmP, Min Original)	-	1800	1300+500
5.12 Table - 1 (i) (b)(Longitudinal direction)	-	1300	-
5.12 Table - 1 (i) (c)(Transverse direction)	-	1300	-
5.12 Table - 1 (i) (d)(After ageing at 70-+1 C for 168 h)	-	3100	2600+500
5.12 Table - 1 (ii) (a)(Breaking strength, kg/5 cm, Min Original)	-	3100	2600+500
5.12 Table - 1 (ii) (b)(Longitudinal direction)	-	1300	-
5.12 Table - 1 (ii) (c)(Transverse direction After ageing at 70-+ 1 C for 168 h)	-	1300	-
5.12 Table - 1 (iii)(Bursting strength, -kg/cm2, Min Original)	-	1000	-
5.12 Table - 1 (iv)(Loss of plasticizers, percent hy mass, Max)	-	1100	-
5.13(Ease of fn situ Repair)	-	500	-
4.1.1(Type Tests)	-	500	-
4.1.2(Acceptance Tests)	-	500	-
5.1(Material)	-	2000	-
5.2(Workmanship)	-	500	-
5.3(Subtance)	-	500	-
5.4(Mass of the cover)	-	500	-
5.5(Fumigation Retention Test)	-	6000	-
5.6(Accelerated Ageing Test)	-	4200	-
5.7(Water Proofness Test)	-	1000	-
5.8(Strength of Joints)	-	1100	-
5.9(Blocking Test)	-	1100	-
5.1(Flex Test)	-	1500	-
5.11(Construction of Fumigation Covers ( for Type 1 and Type 2 ))	-	500	-
5.12 Table - 1 (i) (a)(Tensile strength kg/cmP, Min Original)	-	1300	-
5.12 Table - 1 (i) (b)(Longitudinal direction)	-	1300	-
5.12 Table - 1 (i) (c)(Transverse direction)	-	1300	-
5.12 Table - 1 (i) (d)(After ageing at 70-+1 C for 168 h)	-	4200	-
5.12 Table - 1 (ii) (a)(Breaking strength, kg/5 cm, Min Original)	-	1300	-
5.12 Table - 1 (ii) (b)(Longitudinal direction)	-	1300	-
5.12 Table - 1 (ii) (c)(Transverse direction After ageing at 70-+ 1 C for 168 h)	-	1300	-
5.12 Table - 1 (iii)(Bursting strength, -kg/cm2, Min Original)	-	1100	-
5.12 Table - 1 (iv)(Loss of plasticizers, percent hy mass, Max)	-	2000	-
5.13(Ease of fn situ Repair)	-	500	-

31 Dec, 2026

-
Included w.e.f. 20.01.2025

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

PE 80, 12mm to 75mm

39538 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3.1(UV Stabilizer)	-	2000	NIL
5.4(Aluminium)	-	1800	Tensile 1300+Specimen 500
8(COLOUR)	-	500	NIL
9(DIMENSIONS OF PIPE)	-	500	NIL
9.3(Length of Straight Pipe)	-	0	NIL
9.4(Coiling)	-	0	NIL
10(VISUAL APPEARANCE)	-	500	NIL
11.1(Density (Method of test as per Table 3))	-	700	NILNIL
11.2(Melt Flow Rate (Method of test as per Table 3))	-	1100	NIL
11.3(Overall Migration)	-	1700	Specimen/conditioning charge-625
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	2200	NIL
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	1625	CBC 925 CBD 700
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	700	NIL
11.7(Resistance to Weathering)	-	36000	NIL
11.8(Adhesion Test)	-	1100	NIL
11.9(Apparent Tensile Strength of Pipe)	-	1100	Specimen/Conditioning charge-500
11.10(Minimum Burst Pressure)	-	1000	NIL
11.11(Hydraulic Characteristics)	-	2700	NIL
5(MATERIALS)	-	0	Nil
6(PRESSURE RATING)	-	0	Nil
7(NOMINAL DIAMETERS)	-	0	Nil
14(MARKING)	-	0	Nil
9.2.1(Method of Measurements)	-	0	Nil
11.11.1(Short Term Hydrostatic Tests)	-	0	Nil
11.11.12(Long Term Hydrostatic Test)	-	0	Nil

31 Dec, 2026

-
Exclusion : Tsble 3 (Antioxidant) Cl 5.0 (5.1, 5.2.1, 5.2.1.1)

IS 15827 (2019)

Cladding films for greenhouse / polyhouse - Specifications (First Revision)

1888125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material Identification)	-	2000	NIL
6.1(Appearance & surface finish)	-	500	NIL
6.2(Durability ref clause No. 7.5)	-	0	Exposure charges are extra with full testing charge 13088 as per requirements.
7.1(Visual)	-	500	NIL
Cl. no. 6.3 & Table 2(Tensile strength & elongation at break (TD & MD))	-	3100	TD 1300 MD 1300 Specimen 500
6.3(Dart Drop test)	-	1100	NIL
6.3(Total Visible Light Transmittance)	-	700	NIL
6.3(Haze)	-	700	NIL
6.3(Tear Strength ( MD & TD))	-	2700	TD 1100 MD 1100 Specimen 500
7.4(IR eefectiveness)	-	2500	NIL
7.2(width)	-	500	NIL
7.3(Elongation under Steady Load MD)	-	0	added in tensile charges
7.5(Elongation after UV Exposure MD)	-	0	added in tensile charges

31 Dec, 2026

-
-

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

PE-80, PE-100, 16mm to 500mm

402000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.4(Colour)	-	500	NIL
5.6(Resistance to Weathering)	-	36000	NIL
7(Finish)	-	5005	NIL
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	11000	NIL
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	4800	NIL
8.2(Reversion Test)	-	700	NIL
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	NIL
8.7(Volatile Matter Content)	-	700	NIL
8.3(Density)	-	500	NIL
8.4(Melt Flow Rate (MFR))	-	1100	NIL
5.3(Anti-oxidant)	-	0	NIL
5.4(U-V stabilizer)	-	0	NIL
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	500	NIL
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	NIL
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	NIL
5.1, 5.7 Table 2(iv) Volatile content)	-	700	NIL
4.3(Nominal Diameter)	-	500	NIL
5.1(Polyethylene compound)	-	500	NIL
5.7(PE Compound Quality Evaluation)	-	0	NIL
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	Chemical charges extra or provided by party
6.1(Outside Diameter)	-	500	NIL
6.1(Out of Roundness (Ovality))	-	0	NIL
6.2(Wall Thickness)	-	500	NIL
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	15500	Type and acceptance test
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1800	Test charges 1300 + specimen charges 500
8.9(Resistance to Weathering)	-	0	NIL
6.4(Length of Pipe)	-	500	NIL
8.5(Pigment Dispersion)	-	700	NIL
8.10(Slow Crack Growth Rate Test)	-	10800	Type & acceptance test
8.11(Squeeze-off)	-	1300	NIL
10(Marking)	-	500	NIL
5.1, 5.7 Table 2(v) Water content1))	-	700	NIL
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	700	NIL
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	charge added above

31 Dec, 2026

-
Exclusion : Cl 5.3 (Anti oxidant) Cl 5.4 ( UV Stabilizer)

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

7475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour of fittings)	-	500	NIL
7.1,Table 1(Wall thickness)	-	500	NIL
7.2 ,Table 2&3(Socket Dimensions)	-	0	NIL
10(Workmanship)	-	500	NIL
11(Design requirements)	-	500	NIL
12.1(Visual appearance)	-	500	NIL
12.2(Stress relief test)	-	700	NIL
12.3(Vicat softening tempewrature)	-	1100	NIL
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	NIL
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200	NIL
Cl.15, Annex B(Sulphated Ash Content)	-	1200	NIL
16.1(Impact test)	-	1100	NIL
17(Watet tightness of joint)	-	850	NIL
12.4(Effect on water test)	-	3000	NIL

31 Dec, 2026

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

20-500mm

34031 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	500	NIL
7.4 table -3 & 4(6.1 Dimensions)	-	500	NIL
6.2.1(6.1.1 Identification Stripes)	-	1050	NIL
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	a) Hyd. Test - 48 hrs. b) Hyd.Test - 100 hrs c) Hyd.Test - 1000 hrs d) Hyd.Test - 165 hrs.
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	NIL
8.2(Longitudinal Reversion Test)	-	1200	Test charges 700 + specimen charges 500
8.6(Overall migration)	-	2000	NIL
8.7(Density)	-	700	NIL
8.4( Melt Flow Rate)	-	1100	NIL
8.5 (Oxidation Induction Time)	-	2200	NIL
8.8(Tensile Strength for Butt-fusion)	-	1800	Test charges 1300 + specimen charges 500
8.9 table-6(Elongation at Break)	-	0	Charge added in tensile test
8.10(Slow Crack Growth Rate)	-	6000	Test charges 5500 + specimen charges 500
8.3(Carbon black)	-	925	NIL

31 Dec, 2026

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

9825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	1000	NIL
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	NIL
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	500	NIL
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	NIL
9.1( Visual Appearance)	-	500	NIL
9.3(Density IS 12235 (Part 14))	-	700	NIL
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	test charges 1000 + specimen 500
9.5(Tensile Strength IS 12235(Part 13))	-	1800	test charges 1300 + specimen 500
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	NIL
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0	NIL
9.2(Internal Diameter)	-	500	NIL
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	NIL
5.0(Colour of Pipes)	-	500	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	NIL
7.3.1(No.of Ribs)	-	0	NIL
7.3.2(Rib height)	-	0	NIL
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	0	NIL
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	500	NIL
4.1.2(K-Value as per IS-4669)	-	1100	NIL
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000	NIL

31 Dec, 2026

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

Type - A & B

16788 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	NIL
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	NIL
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	NIL
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	NIL
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	NIL
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	NIL
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	NIL
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	500	NIL
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	500	NIL
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1200	Test charge (700) + Specimen charge(500)
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	NIL
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	NIL
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	NIL
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	NIL
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1600	test charges (1100) + Specimen charge (500)
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1800	test charge (1300) + Specimen charge (500)
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	NIL
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	NIL
8.6(Effect on Water Test)	-	3000	NIL

31 Dec, 2026

-
-

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

15-175mm

140438 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	NIL
9.1(Visual Appearance)	-	500	NIL
9.2 IS 12235 (Part 3)(Opacity)	-	700	NIL
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700	NIL
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100	NIL
9.6 IS 12235(Part 14)(Density)	-	700	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	16650	a) Acceptance Test - 1 hr/27 C b) Type Test - 95 C/165 hrs c) Type test - 95 C/1000 hrs.
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110500	NIL
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1600	test charges 1100 + specimen 500
10.4 IS 12235(Part 19)(Flattening Test)	-	500	NIL
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1800	test charges 1300 + specimen 500
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11300	NIL
7.1.2(Wall Thickness (Maximum))	-	0	NIL
7.1.1(Outside Diameter at any point (Maximum))	-	0	NIL
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0	NIL
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	NIL
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	NIL

31 Dec, 2026

-
-

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

16-200mm

108644 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Dimensions Of Pipes)	-	500	NIL
Cl 8(Visual Appearance)	-	500	NIL
Cl 9.1(Hydraulic Characteristics)	-	18500	Acceptance & Type test
Cl 9.2(Fusion Compatibility)	-	4800	NIL
Cl 9.3(Reversion Test )	-	1200	test charges 700 + specimen charges 500
Cl 9.4 & Annex B(Impact Strength)	-	1600	test charges1100 + specimen charges 500
Cl 9.5(Density)	-	700	NIL
Cl 9.6(Melt Flow Rate)	-	1100	NIL
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	NIL
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	NIL
Cl 9.9(Opacity)	-	700	NIL

31 Dec, 2026

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

All

14156 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	NIL
4.2.3(Carbon Dispersion Test)	-	700	NIL
5.4(Wall Thickness above effective height)	-	500	a) Wall Thickness upon effective height b) Wall Thickness upon effective height
6.1(Finish)	-	500	Visual Appearance
7.1.1(Resistance to Deformation)	-	700	NIL
7.2(Resistance to Impact)	-	1000	NIL
7.4(Tensile Strength)	-	1800	Test charges 1300 + specimen 500
7.5(Flexural Modulus)	-	1600	Test charges 1100 + specimen 500
7.6(overall Migration)	-	2200	Test in water & Acetic Acid
9.1(Man-Hole and Hand-Hole Lids)	-	0	NIL
9.1(Lid Thickness)	-	500	NIL
9.2(Man-Hole and Hand-Hole Lids)	-	500	Lid lockup

31 Dec, 2026

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

21325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	0	Included in visual test
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	included in dimension test
10.7(Sulphated Ash Content)	-	1200	NIL
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	NIL
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	included in dimension test
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	included in dimension test
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	included in dimension test
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	included in dimension test
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	included in dimension test
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	included in dimension test
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	included in dimension test
7.2.1(DIMENSIONS-Socket)	-	0	included in dimension test
7.2.1(DIMENSIONS-Socket)	-	0	included in dimension test
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	included in dimension test
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	included in dimension test
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	included in dimension test
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	included in dimension test
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	included in dimension test
8(SEALING RINGS)	-	0	included in dimension test
6.1.2(PVC Resin)	-	1100	NIL
9.1(PIPE ENDS)	-	0	included in dimension test
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	NIL
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	700	NIL
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	700	NIL
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	NIL
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	NIL
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	NIL
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	NIL
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	NIL
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	NIL
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	NIL
11.2(Resistance to External Blows at 0°C)	-	1500	test charges 1000 + specimen 500
10.3(Effect on Water Test)	-	3000	NIL
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	0	included in dimension test
7.1.4(Length)	-	0	included in dimension test

31 Dec, 2026

-
-

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

4288 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	2050	HYDRAULIC-RS. 850 + OPACITY-RS. 700+DIMENSION 500
3.2.1, Table-1, Fig-1(B)	-	0	NIL
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	0	NIL
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	NIL
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	NIL
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	NIL
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	NIL
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	NIL
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	NIL
3.2.1, Table-1, Fig-1(Nominal size)	-	0	NIL
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	0	NIL
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	0	NIL

31 Dec, 2026

-
-

IS 15532 (2004)

Plastics crates for fruits and vegetables - Specification

11400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 3.1(Requirements)	-	4500	Identification- Rs. 2000 Colour -Rs. 500 Presence of UV stablizer-2000
3.2(Material)	-	1800	Density-Rs. 700 MFI-Rs. 1100
3.3(Shape, Dimensions and Design)	-	500	NIL
3.4(Mass)	-	500	NIL
3.5(Appearance and Surface Finish)	-	500	NIL
3.6(Dimensional Stability)	-	700	NIL
3.7(Confluence Line Strength)	-	1100	NIL
3.8.1(Compressive Strength (Resistance to Applied Load))	-	1100	NIL
3.8.2(Resistance to Drop)	-	1100	NIL
3.9(Resistance to Environmental Stress Cracking)	-	1200	NIL
3.10.1(Suspension Test)	-	2200	NIL
3.10.2(Free-Fall Test)	-	0	NIL

31 Dec, 2026

-
-

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

3825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	500	NIL
7.2(Flow path in emitters)	-	500	NIL
7.3.1(Resistance to Hydrostatic pressure)	-	1000	NIL
7.4.1(Emitter Pull Out In-line emitters)	-	500	NIL
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1000	NIL
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	1000	NIL
8.3(Determination of Emitter Exponent)	-	600	NIL

31 Dec, 2026

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

18993 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5 and Table 1 i(Capacity)	-	500	NIL
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	NIL
4.1(Raw Material)	-	1050	NIL
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	NIL
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	2200	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
4.3(Sacks)	-	500	NIL
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	NIL
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	NIL
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	NIL
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	test Charges 2200(Warp, weft) +10180 UV Exposure
5.2 and Table 1 x(Ash content )	-	1200	NIL
5.3(UV Resistance)	-	10180	Nil

31 Dec, 2026

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

18618 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	NIL
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	700	NIL
3.3.1(Bottom seam (IS 10789))	-	500	NIL
3.3.1(Bottom seam (IS 10789))	-	0	NIL
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	NIL
4.2 and Table 1 ii(Dimensions )	-	500	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
4.2 and Table 1 v(Mass of sack )	-	500	NIL
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	NIL
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	NIL
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	200 (LW & WW) + 10180 UV Exposure charges
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	NIL
4.2 and Table 1 x(Ash content )	-	1200	NIL

31 Dec, 2026

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

7975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	500	NIL
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	500	NIL
7.1.2(Maximum and minimum outside diameter of conduit)	-	1000	NIL
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	NIL
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000	NIL
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1100	NIL
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1100	NIL
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1000	NIL
10(Resistance to Heat -Ball presure test)	-	700	NIL
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	700	NIL
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1600	test charges 100 + specimen 500
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1600	test charges 100 + specimen 500

31 Dec, 2026

-
-

IS 9271 (2004)

Unplasticized polyvinyl chloride (UPVC) single wall corrugated pipes for drainage - Specification (First Revision)

9275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2, 8(Wall Thickness)	-	500	NIL
7.3(Length)	-	0	NIL
7.4.1,Table 2(Perforation Requirement-(Refer Table 2))	-	500	NIL
8.1.2(Visual Appearance, Workmanship and Finish)	-	500	NIL
8.2(Density-When tested in accordance with ]S 13360 (Part 3/Sec 1), the densi of the pipe shall be between 1.40 and 1.46 gm/cm3 .)	-	700	NIL
8.3,Table 3(Pipe stiffness-(Refer Annex A))	-	1100	NIL
8.4,Table 3(Impact Strength at 0 degree C- (refer Annex B))	-	1600	test charges 100 + specimen 500
8.5(Elongation Test-(Annex C,)- pipes shall not elongate more than 7.5 percent)	-	1100	NIL
8.6(BendIng Test-(Annex D,))	-	1000	NIL
8.7(Joints)	-	1000	NIL
7.2, 8(Wall Thickness)	-	500	NIL

31 Dec, 2026

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

4313 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2(diameter of the socket of cap)	-	500		NIL

31 Dec, 2026

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

4313 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
table 1 sl.no: 01(16 )	-	500		NIL
2.2.3(Socket length)	-	500		NIL

31 Dec, 2026

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

4313 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 2.2.2(Dimensions)	-	500		NIL
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000		NIL

31 Dec, 2026

-
-

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

18150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	included in dimension test
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	included in dimension test
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	0	included in dimension test
6.1.3 (Length of Pipe)	-	0	included in dimension test
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	0	included in dimension test
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	included in dimension test
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	included in dimension test
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	included in dimension test
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	included in dimension test
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	included in dimension test
6.1.4.1 (e3min=0.75e)	-	0	included in dimension test
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	included in dimension test
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	included in dimension test
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	included in dimension test
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	included in dimension test
7.1(Appearance:- )	-	500	Nil
7.2(Colour )	-	500	Nil
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	Nil
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1200	Test Charges-700 + Specimen charge-500
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1600	Test Charges-1100 + Specimen charge-500
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1600	Test Charges-1100 + Specimen charge-500
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	850	Nil
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	Nil
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	850	Nil
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	Nil
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	850	Nil
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	Nil
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	NIL

31 Dec, 2026

-
-

IS 15909 (2020)

PVC Geomembranes for Lining - Specification ( Second Revision )

Type: I,II,III,IV,V

47525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,Table 1(Length )	-	500	charges of Length + width is Rs. 250
5,Table 1(Width )	-	0	Nil
5,Table 1(Thickness)	-	500	Nil
5,Table 1(Specific Gravity)	-	700	Nil
5,Table 1( Tensile strength (Longitudinal) ,kg/m2)	-	3100	LD-1300 TD-1300 Specime-500
5,Table 1(Elongation at break (Longitudinal),250 % ,Min)	-	0	NIL
5,Table 1( Tensile strength (Transverse) ,kg/m2)	-	0	NIL
5,Table 1(Elongation at break (Transverse),250 % ,Min)	-	0	NIL
5,Table 1(Tear resistance (machine direction))	-	1100	NIL
5,Table 1(Tear resistance (Cross direction))	-	1100	NIL
5,Table 1(Index puncture resistance,N)	-	1100	NIL
5,Table 1(Low temperature crack resistance)	-	1500	Testing charge- 1000 + specimen charge-500
5,Table 1(Hydrostatic resistance,kg/cm2,Min)	-	1000	NIL
5,Table 1(Seam strength,kg,Min)	-	1100	NIL
5,Table 1(Volatile Loss ,% ,Max)	-	700	NIL
5,Table 1(Peel strength,kN/m,Min)	-	1100	NIL
5,Table 1(Resistance to soil burial)	-	0	NIL
5,Table 1(Tensile strength (Longitudinal),% change)	-	7800	NIL
5,Table 1(Elongation at break (Longitudinal),% change)	-	0	NIL
5,Table 1(Tensile strength (Transverse),% change)	-	0	NIL
5,Table 1(Elongation at break (Transverse),% change)	-	0	NIL
5,Table 1(Water extraction,% loss in weight)	-	600	NIL
5,Table 1(Stability to ultraviolet radiations,% retension in Tensile strength)	-	28800	Test charges 1300 + condition charges 27500
5,Table 1(Stability to ultraviolet radiations,% retension in Elongation at break)	-	1100	NIL
7.0(Colour ,Surface characteristics and fredom from defects)	-	500	NIL
7.1(Colour ,Surface characteristics and fredom from defects)	-	0	NIL
7.2(Colour ,Surface characteristics and fredom from defects)	-	1050	charge for identification clause 3.0
5, Table-2(Horizontal rate of burning)	-	1500	NIL
5, Table-2(Vertical rate of burning)	-	0	NIL
6.0(Dimensions and tolerances)	-	500	NIL
5, Table-2(Length)	-	500	NIL
5, Table-2(Width)	-	0	NIL
5, Table-2(Thickness at 20kPa pressure)	-	500	NIL
5, Table-2(Tensile Strength (Longitudinal))	-	1100	NIL
5, Table-2(Tensile Strength (Transverse))	-	1100	NIL
5, Table-2(Behaviour during perforation)	-	1100	NIL
5, Table-2(Tear Strength (Machine direction))	-	1100	NIL
5, Table-2(Tear Strength (Cross direction))	-	1100	NIL
5, Table-2(Height of fall without perforation)	-	1100	NIL
5, Table-2(Cold crack resistance at low temperature)	-	1500	1000+500 (Test charge = Specimen charge)
5, Table-2(Hydrostatic Pressure Resistance)	-	1000	NIL
5, Table-2(Dimensional Stability at 80 degree C)	-	1250	NIL
5, Table-2(Resistance to acid and alkali)	-	34100	3300 + 30800 (Test charge + Specimen charge)
5, Table-2(Change in length after heating)	-	550	NIL
5, Table-2(Change in width after heating)	-	0	NIL
5, Table-2(Resistance to static puncturing)	-	1100	NIL

31 Dec, 2026

-
Scope restricted to Category A

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

8369 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	NIL
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	NIL
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	500	NIL
6.1(Visual Appearance)	-	500	NIL
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000	NIL
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000	NIL
7.2(Reversion Test)	-	1200	test charges 700 + specimen charges 500
7.3(Tensile Test)	-	1800	test charges 1300 + specimen charges 500
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	NIL

31 Dec, 2026

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

21430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	Identification
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	Fabric
4.3(Sacks)	-	500	Visual Appearance
4.4 and Table 1 i(Capacity)	-	500	NIL
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
5.1 and Table 1 v(Mass of sack )	-	500	NIL
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	2200	warp-1100 Weft-1100
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	0	NIL
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	NIL
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	NIL
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	10180	U.V exposure 192 Hrs.
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	2200	Breaking Strength - Lengthwise & Breadthwise
5.2 and Table 1 x(Ash content )	-	1200	NIL

31 Dec, 2026

-
-

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

86405 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Cord Beading - IS 15907)	-	500	Diameter of Cord Beading
5.2.1(Lamination- IS 15907)	-	500	Lamination
5.3.1(Construction- IS 15907)	-	500	NIL
6.1(Width - IS 15907)	-	500	NIL
5.3.2(Construction- IS 15907)	-	500	NIL
5.4(Bonding- IS 15907)	-	500	NIL
6- Table 1- SL.No (i)(Mass)	-	500	NIL
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	3100	a) Warp direction Rs 1300 b) Weft direction Rs 1300 Specimen 500
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	2700	a) Warp direction Rs 1100 b) Weft direction Rs 1100 Specimen 500
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	0	NIL
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	3100	a) Warp direction Rs 1300 b) Weft direction Rs 1300 Specimen 500
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	1100	NIL
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	1100	NIL
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	1100	NIL
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	2000	test charges 1500 + specimen charges 500
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	2500	test charges 2000 + specimen charges 500
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	2000	test charges 1500 + specimen charges 500
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	1350	NIL
6.1(Length -IS 15907)	-	500	NIL
6.1(Height - IS 15907)	-	500	NIL
6.2(Water Proofness,IS 7941)	-	6700	a) Before Ageing b) After Ageing c) Ageing 70 C/168 hrs.
5.2.2(coating thickness of the sandwich lamination- method A of IS 13162 (Part 3))	-	500	NIL

31 Dec, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET, Lucknow

B-27 Amausi Industrial Area Nadarganj Lucknow, Luknow, Lucknow, Uttar Pradesh, 226008

7052009477 cipetlko2@gmail.com

Scope List