BIS - LIMS (Laboratory Information Management System)

DVG Laboratories & Consultants Pvt Ltd

A2/71, Site-V, UPSIDC Industrial Area Kasna, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201308

9818254877 dvglabs.testing@hotmail.com

Scope List

Reset

6 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

Fe 415, Fe 415D, Fe 415S Fe 500, Fe 500D, Fe 500S Fe 550, Fe 550D Fe 600 Fe 650 Fe 700

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	1000	-
Cl 9.3(Load In One Direction)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	800	-
4.1(Sulphur and phosphorous)	-	1000	-
4.1(Sulphur %)	-	800	-
4.1(Phosphorus %)	-	800	-
4.1(Carbon %)	-	800	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 7.2 Table -2 (Nominal Mass)	-	800	-
Cl. 6.1(Nominal Size)	-	500	-
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	800	-
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	800	-
4.1( Nitrogen%)	-	800	-
4.1(Ni)	-	800	-
4.1(Mo)	-	800	-
4.1(Cr)	-	800	-
4.1( Ti)	-	800	-
4.1(V)	-	800	-
4.1( Nb)	-	800	-
4.1( Aluminium %)	-	800	-
4.1( Copper %)	-	800	-
4.1(Silicon %)	-	800	-
Clause 4.2 Note 2, Amendment 1 & 3(Nb+V+B+Ti)	-	1000	-
Clause 4.2 Note 3, Amendment 1 & 3(Cr+Cu+Ni+Mo+P)	-	1000	-
4.2(Niobium (Nb))	-	1000	-
4.2(Boron (B))	-	1000	-
8.18.1 Table 3(Total elongation at maximum force)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	1000	-

10 Dec, 2028

-
Cl 5.1 Pull out test

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

Pulverized Fuel Ash

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	1500	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	1000	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	900	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	800	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	800	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	800	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1500	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	800	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	2500	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	2500	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	2000	-
7.2(Uniformity Requirements)	-	0	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	2500	-
5.1&7.1, table-2 (III)(Lime Reactivity)	-	2500	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	2500	-

10 Dec, 2028

-
-

IS 14268 (2022)

Uncoated stress relieved low relaxation seven-wire (ply) strand for prestressed concrete -Specification (Second Revision)

9.0, 9.3, 9.6, 11.0, 11.3, 12.5, 12.7, 12.9, 13.0, 15.2

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.2(Carbon)	-	800	-
4.1.2(Silicon)	-	800	-
4.1.2(Manganese)	-	800	-
4.1.2(Sulphur)	-	800	-
4.1.2(Phosphorus)	-	800	-
4.1.2(Chromium)	-	800	-
4.1.2(Nickel)	-	800	-
4.1.2(Molybdenum)	-	800	-
4.1.2(Copper)	-	800	-
4.1.2(Aluminum)	-	800	-
4.1.2(Sulphur + Phosphorus)	-	1000	-
4.1.2(Boron)	-	800	-
4.1.2(Titanium)	-	800	-
4.1.2(Niobium)	-	800	-
4.1.2(Vanadium)	-	800	-
4.1.2(Titanium+Niobium+Vanadium)	-	1500	-
4.1.2(Nitrogen)	-	1000	-
4.1.3(Wire Description)	-	0	-
4.1.4(Table 1)(Indentations Description)	-	0	-
4.1.4(Table 1)(Nominal Depth of Oval Type Indentation)	-	500	-
4.1.4(Table 1)(Length of Oval Type Indentation)	-	500	-
4.1.4(Table 1)(Spacing Between Oval Type Indentations)	-	500	-
4.2(Strand Lay Length)	-	1000	-
4.2(Difference In Diameter Of Centre Wire And Surrounding Wire Of Strand)	-	500	-
4.2(Forming of wire)	-	0	-
4.3(Joints)	-	0	-
4.5(Workmanship and Finish)	-	500	-
6(Table 2)(Diameter)	-	500	-
6(Table 2)(Tensile Strength)	-	1000	-
6(Table 2)(Cross Sectional Area)	-	500	-
6(Table 2)(Mass Per Meter)	-	500	-
6(Table 2)(Breaking Load)	-	1000	-
6(Table 2)(0.2 Percent Proof Load)	-	1000	-
6.2.3(Elongation)	-	1000	-
6.2.4(Relaxation Properties(Relaxation Loss-100h))	-	0	I have no facilities in testing parameter.
6.2.4(Relaxation Properties(Relaxation Loss-1000h))	-	0	I have no facilities in testing parameter.
6.3(Straightness of Strand)	-	1000	-
6.4(Behavior During Cutting)	-	1000	-

10 Dec, 2028

-
Cl 6.2.4 Relaxation Properties

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

OPC 33/ OPC 43/ OPC 53/ OPC 43S/ OPC 53S

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional))	-	0	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iii b(Setting Time Final)	-	1200	-
7 Table-3 iii a(Setting Time Initial)	-	1200	-
7 Table-3 ii b(Expansion after aeration)	-	1000	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii a(Expansion after aeration)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	1000	-
7 Table-3 i.(Fineness)	-	1000	-
6.1 Table-2 viii(Alkali content)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-
6 - Table - 1 viii(Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	500	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	500	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	500	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	500	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	500	-
7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iii b(Setting Time Final)	-	1200	-
7 Table-3 iii a(Setting Time Initial)	-	1200	-
7 Table-3 ii b(Expansion after aeration)	-	1000	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii a(Expansion after aeration)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	1000	-
7 Table-3 i.(Fineness)	-	1000	-
6.1 Table-2 viii(Alkali content)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-
6 - Table - 1 viii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	500	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	500	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	500	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	500	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	500	-
7.1.8(Pump efficiency shall be as per 11.4)	-	0	-
Clause 7 Table 3, SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1500	-
Clause 7 Table 3, SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1500	-
Clause 7 Table 3, SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1500	-
Clause 7 Table 3, SI No. (v) (Transverse Strength, 672 ± 4 h)	-	3000	-
Clause 7 Table 3, SI No. (v) (Transverse Strength, 168 ± 2 h)	-	3000	-
Clause 7 Table 3, SI No. (v) (Transverse Strength, 72 ± 1 h)	-	3000	-
7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional))	-	0	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iii b(Setting Time Final)	-	1200	-
7 Table-3 iii a(Setting Time Initial)	-	1200	-
7 Table-3 ii b(Expansion after aeration)	-	1000	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii a(Expansion after aeration)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	1000	-
7 Table-3 i.(Fineness)	-	1000	-
6.1 Table-2 viii(Alkali content)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	1000	-
7 Table-3 ii a(Expansion after aeration)	-	1000	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii b(Expansion after aeration)	-	1000	-
7 Table-3 iii a(Setting Time Initial)	-	1200	-
7 Table-3 iii b(Setting Time Final)	-	1200	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional))	-	0	-
11(Marking)	-	0	-
5(Manufacture)	-	0	-
9(Manufacture certificate)	-	8500	-
10(Packing)	-	0	-
15.2.1(Records characteristics)	-	0	-
15.2.2(Measured data unit)	-	0	-
15.2.3(Fixed length record )	-	0	-
15.2.4(Variable length record)	-	0	-
15.2.5(segmented records)	-	0	-
15.3(Attributes of record structured files)	-	0	-
15.4(Requirments for systems implementing section 4)	-	0	-
5.1.1 Table 1 Sl. No. iv(Calcium Carbonate)	-	500	-
14(Requirment for an Reciving system )	-	0	-
13(Requirment for an originating system )	-	0	-

10 Dec, 2028

-
Cl 7 -Table 3 Transverse Strength Test

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC – Fly ash based

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	-
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	1200	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	1200	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	1000	-
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	800	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	800	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	800	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	800	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	800	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	800	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	800	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	800	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	800	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	-
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	1200	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	1200	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	1000	-
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	800	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	800	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	800	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	800	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	800	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	800	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	800	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	800	-
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1500	-
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1500	-
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1500	-
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	2000	-
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	2000	-
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	2000	-
11(Marking)	-	0	-
4(RAW MATERIAL)	-	0	-
11(MARKING)	-	0	-

10 Dec, 2028

-
Cl 7 -Table 2 Transverse Strength Test

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

M-30, M-35, M-40

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	1000	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	1000	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	1000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	1000	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	1000	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	1000	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	1000	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	1000	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	1000	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	1000	-
Clause 7.1.3 (Colour and Texture)	-	1000	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	1000	-
Clause 7.1.1 (General Quality)	-	1000	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	1000	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	1000	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	1000	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	1000	-
Clause 3.20(Spacer nibs)	-	0	-
10(Marking)	-	0	-
cl.5(Cement)	-	0	-
5.2(Mineral Admixture)	-	0	-
5.3(Chemical Admixtures)	-	0	-
5.4(Coarse and Fine Aggregates)	-	0	-
5.5(Pigments)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	10000	optional testing
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	10000	optional testing
Clause 7.3, Annex G(Average Breaking Load)	-	2000	-
Clause 7.3, Annex G(Individual Breaking Load)	-	2000	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	2000	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	3000	-
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-	0	-
5.6(Water)	-	0	-

10 Dec, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

DVG Laboratories & Consultants Pvt Ltd

A2/71, Site-V, UPSIDC Industrial Area Kasna, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201308

9818254877 dvglabs.testing@hotmail.com

Scope List