BIS - LIMS (Laboratory Information Management System)

Elutech Laboratory and Calibration Services

Plot No.-1,Bajrang Vihar-9, New Loha Mandi Road, Macheda, Jaipur, Jaipur, Rajasthan, 302013

9783401104 elutechlab@gmail.com

Scope List

Reset

13 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 1117 (2018)

Laboratory glassware - Single - Volume pipettes (Second Revision)

Class- A, AS & B, Cap. upto 100 ml, Both One & Two mark

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1&3(Marking)	-	15000	Complete testing charges for the product (Excluding raw material) is Rs. 15000
3(Class of Accuracy)	-	15000	-
4.1(Nominal capacities)	-	15000	-
4.2(Accuracy)	-	15000	-
5.1(Material)	-	15000	-
5.1.1(Limit of Alkalinity)	-	15000	-
5.2(Pattern of Pipette)	-	15000	-
5.3(Workmanship & Finish)	-	15000	-
5.4(i) Distance of graduation line from top of pipette.)	-	15000	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	15000	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	15000	-
5.4(iv) Wall thickness)	-	15000	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	15000	-
5.4(b) Other pipettes)	-	15000	-
5.4(v) Dia. of safety bulb (if provided ))	-	15000	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	15000	-
5.4(vii) Overall length, L)	-	15000	-
5.4(viii) Length of suction tube, L1 )	-	15000	-
5.4(ix) Length of delivery tube, L2 )	-	15000	-
5.4(x) Internal dia. of suction tube D1 )	-	15000	-
5.4(xi) External dia. of bulb D2 )	-	15000	-
5.4(xii) External dia. of delivery tube D3 )	-	15000	-
5.5(Delivery Time)	-	15000	-
5.5(Delivery Time)	-	15000	-
5.6&7(Graduation line & Visibility )	-	15000	-
6.1.2(Marking)	-	15000	-
6.1.1&3(Marking)	-	15000	-
3(Class of Accuracy)	-	15000	-
4.1(Nominal capacities)	-	15000	-
4.2(Accuracy)	-	15000	-
5.1(Material)	-	15000	-
5.1(Material)	-	15000	-
5.1.1(Limit of Alkalinity)	-	15000	-
5.2(Pattern of Pipette)	-	15000	-
5.3(Workmanship & Finish)	-	15000	-
5.4(i) Distance of graduation line from top of pipette.)	-	15000	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	15000	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	15000	-
5.4(iv) Wall thickness)	-	15000	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	15000	-
5.4(b) Other pipettes)	-	15000	-
5.4(v) Dia. of safety bulb (if provided ))	-	15000	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	15000	-
5.4(vii) Overall length, L)	-	15000	-
5.4(viii) Length of suction tube, L1 )	-	15000	-
5.4(ix) Length of delivery tube, L2 )	-	15000	-
5.4(x) Internal dia. of suction tube D1 )	-	15000	-
5.4(xi) External dia. of bulb D2 )	-	15000	-
5.4(xii) External dia. of delivery tube D3 )	-	15000	-
5.5(Delivery Time)	-	15000	-
5.5(Delivery Time)	-	15000	-
5.6&7(Graduation line & Visibility )	-	15000	-
6.1.2(Marking)	-	15000	-
6.1.1&3(Marking)	-	15000	-
3(Class of Accuracy)	-	15000	-
4.1(Nominal capacities)	-	15000	-
4.2(Accuracy)	-	15000	-
5.1(Material)	-	15000	-
5.1(Material)	-	15000	-
5.1.1(Limit of Alkalinity)	-	15000	-
5.2(Pattern of Pipette)	-	15000	-
5.3(Workmanship & Finish)	-	15000	-
5.4(i) Distance of graduation line from top of pipette.)	-	15000	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	15000	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	15000	-
5.4(iv) Wall thickness)	-	15000	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	15000	-
5.4(b) Other pipettes)	-	15000	-
5.4(v) Dia. of safety bulb (if provided ))	-	15000	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	15000	-
5.4(vii) Overall length, L)	-	15000	-
5.4(viii) Length of suction tube, L1 )	-	15000	-
5.4(ix) Length of delivery tube, L2 )	-	15000	-
5.4(x) Internal dia. of suction tube D1 )	-	15000	-
5.4(xi) External dia. of bulb D2 )	-	15000	-
5.4(xii) External dia. of delivery tube D3 )	-	15000	-
5.5(Delivery Time)	-	15000	-
5.5(Delivery Time)	-	15000	-
5.6&7(Graduation line & Visibility )	-	15000	-
6.1.2(Marking)	-	15000	-

Complete

Included w.e.f. 07.11.2024

IS 710 (2010)

Marine plywood - Specification (Second Revision)

12500 View breakup
Rs. 12500/- for complete testing excluding raw material testing.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(MARKING)	-	12500	Rs 12500 for complete testing excluding raw material testing.
11.2(MARKING)	-	12500	-
7.1(WORKMANSHIP AND FINISH )	-	12500	-
7.2(WORKMANSHIP AND FINISH )	-	12500	-
7.3(WORKMANSHIP AND FINISH )	-	12500	-
7.5(WORKMANSHIP AND FINISH )	-	12500	-
6.1(DIMENSIONS)	-	12500	-
6.2(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
9.1.1(MOISTURE CONTENT)	-	12500	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	12500	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	12500	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	12500	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	12500	-
9.1.5(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	12500	-
9.1.4(Tensile strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.8(Retention of preservative)	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	12500	-
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	12500	-
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	12500	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	12500	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	12500	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	12500	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	12500	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	12500	-
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	12500	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	12500	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	12500	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	12500	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	12500	-
cl.5.1(manufacture - Veneers)	-	12500	-
cl.5.1(manufacture - Veneers - moisture content)	-	12500	-
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	12500	-
cl.5.2.2(Assembly - Thickness of Veneers)	-	12500	-
6.1(DIMENSIONS)	-	12500	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	12500	-
11.1(MARKING)	-	0	-
11.2(MARKING)	-	0	-
7.1(WORKMANSHIP AND FINISH )	-	12500	-
7.2(WORKMANSHIP AND FINISH )	-	12500	-
7.3(WORKMANSHIP AND FINISH )	-	12500	-
7.5(WORKMANSHIP AND FINISH )	-	12500	-
6.1(DIMENSIONS)	-	12500	-
6.2(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
9.1.1(MOISTURE CONTENT)	-	12500	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	12500	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	12500	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	12500	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	12500	-
9.1.5(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	12500	-
9.1.4(Tensile strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.8(Retention of preservative)	-	12500	-
cl.5.1(manufacture - Veneers)	-	12500	-
cl.5.1(manufacture - Veneers - moisture content)	-	12500	-
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	12500	-
cl.5.2.2(Assembly - Thickness of Veneers)	-	12500	-
6.1(DIMENSIONS)	-	12500	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	12500	-
11.1(MARKING)	-	12500	-
11.2(MARKING)	-	12500	-
7.1(WORKMANSHIP AND FINISH )	-	12500	-
7.2(WORKMANSHIP AND FINISH )	-	12500	-
7.3(WORKMANSHIP AND FINISH )	-	12500	-
7.5(WORKMANSHIP AND FINISH )	-	12500	-
6.1(DIMENSIONS)	-	12500	-
6.2(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
9.1.1(MOISTURE CONTENT)	-	12500	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	12500	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	12500	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	12500	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	12500	-
9.1.5(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	12500	-
9.1.4(Tensile strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.8(Retention of preservative)	-	12500	-
cl.5.1(manufacture - Veneers)	-	12500	-
cl.5.1(manufacture - Veneers - moisture content)	-	12500	-
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	12500	-
cl.5.2.2(Assembly - Thickness of Veneers)	-	12500	-
6.1(DIMENSIONS)	-	12500	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	12500	-
11.1(MARKING)	-	12500	-
11.2(MARKING)	-	12500	-
7.1(WORKMANSHIP AND FINISH )	-	12500	-
7.2(WORKMANSHIP AND FINISH )	-	12500	-
7.3(WORKMANSHIP AND FINISH )	-	12500	-
7.5(WORKMANSHIP AND FINISH )	-	12500	-
6.1(DIMENSIONS)	-	12500	-
6.2(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
6.3(DIMENSIONS)	-	12500	-
9.1.1(MOISTURE CONTENT)	-	12500	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	12500	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	12500	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	12500	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	12500	-
9.1.5(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	12500	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	12500	-
9.1.4(Tensile strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.8(Retention of preservative)	-	12500	-
cl.5.1(manufacture - Veneers)	-	12500	-
cl.5.1(manufacture - Veneers - moisture content)	-	12500	-
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	12500	-
cl.5.2.2(Assembly - Thickness of Veneers)	-	12500	-
6.1(DIMENSIONS)	-	12500	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	12500	-
CL-4.2.1(Adhesive)	-	12500	-
CL-5.2.3(Joint in Veneers)	-	12500	-
CL-5.2.4(Grain Direction)	-	12500	-
CL-5.4(Moisture Content)	-	12500	-

Complete

Included w.e.f. 19.09.2024

IS 303 (1989)

Plywood for General Purposes -

Grade - MR & BWR, Type – AA, AB & BB

5200 View breakup
Testing charges (excluding raw material) for BMR grade Rs. 4800/-, MR grade Rs. 5200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	5200	Testing Charges (excluding raw material) for BWR Grade Rs 4800, MR Grade Rs 5200.
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	5200	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	5200	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	5200	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	5200	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	5200	-
11.3(Moisture Content - Part 1 of IS 1734)	-	5200	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	5200	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	5200	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	5200	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	5200	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	5200	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	5200	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	5200	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	5200	-
5.1(Type - For BB Type)	-	5200	-
5.1(Type - For AB Type)	-	5200	-
5.1(Type - For AA Type)	-	5200	-
4(Grade - For MR grade)	-	5200	-
4(Grade - For BWR grade)	-	5200	-
cl. 13.1(marking)	-	5200	-
cl. 13.2(marking)	-	5200	-
Cl-12 (Amendment No-2 OF IS 303)(OPTIONAL REQUIREMENT FOR ECO MARK)	-	5200	-
cl. 13.1(marking)	-	0	-
cl. 13.2(marking)	-	0	-
Cl-12 (Amendment No-2 OF IS 303)(OPTIONAL REQUIREMENT FOR ECO MARK)	-	0	-
cl. 13.1(marking)	-	0	-
cl. 13.2(marking)	-	0	-
Cl-12 (Amendment No-2 OF IS 303)(OPTIONAL REQUIREMENT FOR ECO MARK)	-	0	-
cl. 13.1(marking)	-	0	-
cl. 13.2(marking)	-	0	-
Cl-12 (Amendment No-2 OF IS 303)(OPTIONAL REQUIREMENT FOR ECO MARK)	-	0	-
CL-6.2(Adhesive)	-	5200	-
CL-7.2.3(Grain Direction)	-	5200	-
CL-7.2.1(Thickness)	-	5200	-
CL-7.2.5.1(Gaps in cores and cross-bands)	-	5200	-
CL-8.2(Thickness)	-	5200	-

Complete

Included w.e.f. 19.09.2024

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

Low-form and Tall-form Beaker with spout

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12500	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12500	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12500	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12500	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12500	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12500	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12500	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12500	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12500	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12500	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12500	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12500	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	12500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	12500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	12500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	12500	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	12500	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	12500	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	12500	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	12500	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	12500	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	12500	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	12500	-

Complete

Included w.e.f. 09.11.2024

IS 1381 : Part 1 (2003)

Laboratory glassware - Narrow - Necked boiling flasks (Second Revision)

Conical, Flat & Round Bottom, upto 10000ml

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 4(Type of Flask)	-	11000	-
3.1, 4.1(Series of Nominal Capacity)	-	11000	-
3.2, 4.2(Nominal Capacity )	-	11000	-
3.3, 4.3(Material )	-	11000	-
3.4, 3.4.1 & 4.4, 4.4.1(Construction- a) Stability )	-	11000	-
3.4, 3.4.2 & 4.4, 4.4.2(Construction- b) Neck )	-	11000	-
3.5, 4.5(Dimensions (in mm) (Table 1&2))	-	11000	-
3.5.2(Neck Length)	-	11000	-
3.5.3, 4.5.2(Dimensions of base )	-	11000	-
3.5.4, 4.5.3(Wall thickness)	-	11000	-
5(Marking )	-	11000	-

Complete

Included w.e.f 27.11.2024

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

Wide and Narrow Neck, Class A&B, upto 5000ml

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Material)	-	12000	-
Table 1(Nominal Capacity)	-	12000	-
Table 1(Internal Neck Diameter)	-	12000	-
Table 1(Distance of graduation line)	-	12000	-
Table 1(Overall Height)	-	12000	-
Table 1(Bulb Diameter)	-	12000	-
Table 1(Base Diameter)	-	12000	-
Table 1(Wall Thickness)	-	12000	-
Table 1(Ground joint k4)	-	12000	-
Table 1(Ground joint k6)	-	12000	-
8.3(Shape)	-	12000	-
8.4(Neck)	-	12000	-
8.5(Stopper)	-	12000	-
8.6(Dimensions)	-	12000	-
9.0(Graduation Line)	-	12000	-
Table-2(Nominal capacity)	-	12000	-
Table-2(Internal neck diameter)	-	12000	-
Table-2(Distance of graduation line 1))	-	12000	-
Table-2(Overall height 2))	-	12000	-
Table-2(Bulb diameter)	-	12000	-
Table-2(Base diameter)	-	12000	-
Table-2(Wall thickness)	-	12000	-
Table-2(Ground joint 3) k4)	-	12000	-
Table-2(Ground joint 3) k6)	-	12000	-
12.1(Visibility of graduation line, figures and marking)	-	12000	-
12.2(Visibility of graduation line, figures and marking)	-	12000	-

Complete

Included w.e.f. 22.11.2024

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

Grade- MR & BWP, Type - Decorative & Commercial

6800 View breakup
For MR Grade – Rs. 6,100/- BWP Grade – Rs. 6,800/- (Excluding Raw Materials Testing) 10 % discount to BIS.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.6(Spot test - Annexure L)	-	400	For MR Grade Rs 6100 & BWP Grade Rs6800).10 % discount to BIS GSTIN extra as per govt rule
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	150	-
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	100	-
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	150	-
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	100	-
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1800	-
9.2.3(Adhesion of Plies - Annexure H)	-	400	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	800	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	3300	-
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	100	-
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	100	-
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	300	-
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	300	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	300	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	300	-
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	50	-
7.3(Dimensional Requirements - Squareness - Annexure D)	-	100	-
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	100	-
7.3(Dimensional Requirements - Thickness - Annexure E)	-	50	-
7.3(Dimensional Requirements - Width - 8.1.4)	-	50	-
7.3(Dimensional Requirements - Length - 8.1.4)	-	50	-
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	400	-
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	400	-
9.2.6 (mechanical)(Spot test - Annexure L)	-	400	-
cl. 11(marking)	-	0	-
cl. 11.1(marking - BIS certification marking)	-	0	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO-MARK)	-	0	-

Complete

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

Garde- MR,BWR,BWP. Liquid, Powder, Film

7445 View breakup
For BWR Grade - Rs. 7,445/- BWP Grade – Rs. 7,445/- MR Grade – Rs. 7,000/- 10 % discount to BIS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(BWP (BOiling WaterProof))	-	6000	Testing Charges for BWP Rs. 7800, For BWR Rs 7800, For MR Rs 7000. 10 % discount to BIS
4 Table (i)(BWR (Boiling Water Resistant))	-	6000	-
4 Table (i)(MR (Moisture Ressistant))	-	5200	-
7.4(Acidity and Alkalinity ( pH))	-	1800	-
5,7.4(Keeping Quality (Resistance to heat Polymerization))	-	0	-

Complete

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

Type -1,2,3,4,5&6

12000 View breakup
Rs. 12,000/- 10 % discount to BIS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3 (Table 1)(b) 6 mm and above)	-	50	Complete testing charges (excluding raw material) Rs 12000. 10% discount for BIS
4.1(Flame retardant chemicals)	-	0	-
4.2(Flame retardant and preservative treatment)	-	0	-
4.3(Treatment)	-	0	-
5(PREPARATION FOR TREATMENT)	-	0	-
6.1.1(Treatment of Plywood by Pressure Impregnation after Manufacture)	-	0	-
6.1.2(Soaking Treatment)	-	0	-
6.2(Choice of Treatment)	-	0	-
7(CONDITIONING AFTER TREATMENT)	-	0	-
8.1(Dimensions)	-	100	-
8.2(Thickness)	-	50	-
8.3(Tolerance)	-	200	-
9(WORKMANSHIP AND FINISH)	-	50	-
10(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
11 (a)(For flammability)	-	2000	-
11 (b)(For flame penetration)	-	2000	-
11 (c)(For rate of burning)	-	2000	-
12.1 Table - 2 (i)(Moisture content, percent, Max)	-	400	-
12.1 Table - 2 (ii)(Flammability (see Note 1), minutes, Min)	-	2000	-
12.1 Table - 2 (iii)(Flame penetration (see Note 2), minutes, Min)	-	2000	-
12.1 Table - 2 (iv)(Rate of burning (see Note 3), minutes, Min)	-	2000	-
12.2(Other Tests)	-	5200	-
14(Marking)	-	0	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO-MARK)	-	0	-

Complete

IS 1328 (1996)

Veneered Decorative Plywood -Specification

Grade - MR & BWR, Type 1 & 2

4150 View breakup
Rs. 4,150/- (Excluding Raw Materials Testing) 10 % discount to BIS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	0	10 % discount to BIS GSTIN extra as per govt rule
4.1(Grade - For MR)	-	0	-
4.2(Type - For Type 1)	-	0	-
4.2(Type - For Type 2)	-	0	-
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	300	-
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	300	-
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	300	-
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	300	-
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	300	-
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	300	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	50	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	50	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	50	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	100	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	100	-
9(Finish - Cl. 9.2, 8.3)	-	100	-
9(Finish - Cl. 9.1, 8.3)	-	100	-
11(Tests - Moisture Content - Part 1 of IS 1734)	-	400	-
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	3000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	3000	-
6.1(Decorative Veneers (Thickness))	-	50	-

Complete

IS 4990 (2024)

PLYWOOD FOR CONCRETE SHUTTERING WORKS SPECIFICATION (Fourth Revision)

Type - CS, CSC, CSFF. Formaldehyde Class E1 & E2

15000 View breakup
Rs. 15,000/- (Excluding Raw Materials Testing) 10 % discount to BIS

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Timber)	-	0	Rs 15000 for complete testing excluding raw material testing. 10 % discount to BIS
Cl-5.2(Adhesives for Bonding of Veneers)	-	7800	Resin testing charges extra for BWP Grade Rs 7800
Cl-6.1(Manufacture)	-	0	-
Cl-6.2(Manufacture ( Thickness of veneers))	-	100	Rs 100 for thickness of veneer
Cl-6.3(Manufacture ( Physical and mechanical properties of veneers))	-	0	-
Cl-6.4, 6.7(Manufacture (Plywood for concrete shuttering))	-	0	-
Cl-6.5(Manufacture (Scarf joints))	-	0	-
Cl-6.6(Manufacture ( Preservative treatment))	-	0	-
Cl-7.1(Dimensions (length, width))	-	100	-
Cl-7.2(Thickness)	-	50	-
Cl-7.3(Squareness and Edge Straightness)	-	200	-
Cl-8.1, 8.2(Workmanship and finish)	-	50	-
Cl-10.3(Moisture Content)	-	400	-
Cl-10.4.1(Glue Adhesion in Dry State - Glue Shear Strength)	-	600	-
Cl-10.4.2(Glue Adhesion in Dry State - Adhesion of Plies)	-	400	-
Cl-10.5, 10.5.1(Resistance to Water Test)	-	1400	-
Cl-10.5.1.1(Water Resistance Test-Glue shear strength)	-	900	-
Cl-10.5.1.2(Water Resistance Test-Adhesion of plies)	-	500	-
Cl-10.5.2(Water Resistance Test (Alternate method))	-	0	-
Cl-10.6(Water resistance test (Concrete shuttering Plywood))	-	600	-
Cl-10.7.1, Table-2(Mycological Test- Glue shear strengt)	-	400	-
Cl-10.7.2(Mycological Test- Adhesion of plies)	-	400	-
Cl-10.8(Tensile Strength)	-	1000	-
Cl-10.9, Table-3("Static Bending Strength -Modulus of Elasticity (MOE),")	-	750	-
Cl-10.9, Table-3("Static Bending Strength- Modulus of Rupture (MOR), ")	-	750	-
Cl-10.10, Table-4(Wet Bending Strength -Modulus of Elasticity (MOE),)	-	1000	-
Cl-10.10, Table-4(Wet Bending Strength - Modulus of Rupture (MOR),)	-	1000	-
Cl-10.11(Retention of Preservative)	-	1000	-
Cl-10.12(Formaldehyde Content Test)	-	2000	-
Cl-10.13(Steady-State Formaldehyde Emission Test)	-	0	-

Complete

Exclusion: Cl-10.13 (Steady-State Formaldehyde Emission Test) Optional Test in IS 4990: 2024

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

Formaldehyde Class – E1 & E2

14500 View breakup
Rs. 14,500/- (Excluding Raw Materials Testing) 10 % discount to BIS.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Timber)	-	0	Rs 14500 for complete testing excluding raw material testing. 10 % discount to BIS
Cl-4.2(Adhesive)	-	7800	Resin testing charges extra from IS 710 for BWP Grade Rs 7800
Cl-5.1(Veneers)	-	400	Rs 400 for moisture of veneer
Cl-5.2.1(Glueing)	-	0	-
Cl -5.2.2(Thickness of Veneers)	-	100	Rs 100 for thickness of veneer
Cl - 5.2.3.1(Joint in Veneers)	-	0	-
Cl - 5.2.3.2(Edge joints)	-	0	-
Cl - 5.2.3.3(End joints)	-	0	-
Cl - 5.2.3.4(Scarf joints)	-	0	-
Cl - 5.2.4(Grain Direction)	-	0	-
Cl-5.3(Treatment)	-	1000	-
Cl-5.4(Moisture Content)	-	400	-
Cl-6.1(Dimensions (length and width))	-	100	-
Cl-6.2(Thickness)	-	50	-
Cl-6.3(Squareness and Edge Straightness)	-	200	-
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6(Workmanship and finish)	-	50	-
Cl-9.3(Moisture Content)	-	400	-
Cl-9.4.2(Glue Adhesion in Dry State- Adhesion of Plies)	-	400	-
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength)	-	2100	-
Cl-9.5.1.1(Water Resistance Test-Glue shear strength)	-	600	Testing Charges for Water Resistance Test Rs 2100
Cl-9.5.1.2(Water Resistance Test-Adhesion of plies)	-	400	Testing Charges for Water Resistance Test Rs 2100
Cl-9.5.2(Water Resistance Test)	-	0	-
Cl-9.6(Tensile Strength)	-	1000	-
Cl-9.7(Mycological Test)	-	1800	-
Cl-9.8, Table-2(Static Bending Strength- Modulus of Elasticity (MOE))	-	750	-
Cl-9.8, Table-2(Static Bending Strength- Modulus of Rupture (MOR))	-	750	-
Cl-9.9, Table-3(Wet Bending Strength- Modulus of Elasticity (MOE))	-	1000	-
Cl-9.9, Table-3(Wet Bending Strength- Modulus of Rupture (MOR))	-	1000	-
Cl-9.10(Retention of Preservative)	-	1000	-
Cl-9.11(Formaldehyde Content Test)	-	2000	-
Cl-9.12(Steady-State Formaldehyde Emission Test)	-	0	-
Cl-9.4.2(Adhesion of Plies)	-	400	-

Complete

Exclusion: Cl-9.12 (Steady-State Formaldehyde Emission Test) Optional test as per IS 710: 2024

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

Grade - MR, BWR & BWP, Type – AA, AB & BB. E1 & E2

9100 View breakup
For BWR Grade - Rs. 9,100/- BWP Grade – Rs. 8,900/- MR Grade – Rs. 6,900/- (Excluding Raw Materials Testing) 10 % discount to BIS.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	300	Testing Charges (excluding raw material) for BWR Grade Rs 9100, BWP Grade Rs 8900, MR Grade Rs 6900.
Cl-5.2, Table- 1 (i)(Blister)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (ii)(Checks)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (iii)(Discolouration)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (iv)(Dote)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (v)(Insect hole)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (vi)(Joints)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (x)(Knots (tight))	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (xi)(Patches)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (xii)(Splits)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table- 1 (xiii)(Swirl)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	300	10 % discount to BIS GSTIN extra as per Government Rule
Cl-8.1(Dimensions (length and width))	-	100	10 % discount to BIS GSTIN extra as per Government Rule
Cl-8.2(Thickness of the plywood boards)	-	100	10 % discount to BIS GSTIN extra as per Government Rule
Cl-8.3(Squareness and Edge Straightness)	-	200	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	3000	3000 for BWR Grade, 2800 for BWP Grade, 800 for MR Grade.10 % discount to BIS
Cl-11.3.2(Mycological Test)	-	1900	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.4(Moisture Content)	-	400	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity (MOE)-)	-	500	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.5, Table 4(Static Bending Strength - Modulus of Rupture (MOR)-)	-	500	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.6(Formaldehyde Content Test)	-	2000	10 % discount to BIS GSTIN extra as per Government Rule
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	0	Optional Test as per cl 11.7 of IS 303: 2024
Cl-6.1(Timber)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-6.2(Adhesive)	-	7800	Resin testing charges extra from IS 303 for BWP Grade Rs 7800, BWR Rs 7800 and MR Rs 7000
Cl-7.2.1(Thickness of veneers)	-	500	Rs 100 for thickness of veneer and Rs 400 for moisture of veneer
Cl-7.2.3(Grain Direction)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-7.2.5.2(Splits)	-	0	10 % discount to BIS GSTIN extra as per Government Rule
Cl-7.2.5.3(Overlap)	-	0	10 % discount to BIS GSTIN extra as per Government Rule

Complete

Exclusion: Cl-11.7 (Steady-State Formaldehyde Emission Test) Optional Test as per cl 11.7 of IS 303: 2024

Bureau of Indian Standards

The National Standards Body of India

Elutech Laboratory and Calibration Services

Plot No.-1,Bajrang Vihar-9, New Loha Mandi Road, Macheda, Jaipur, Jaipur, Rajasthan, 302013

9783401104 elutechlab@gmail.com

Scope List