BIS - LIMS (Laboratory Information Management System)

AADHAR TESTING SOLUTIONS LLP, GHAZIABAD

First Floor, Plot no. 02, Gyani Compound, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201005

8810500700 mkvishnoi10@gmail.com

Scope List

Reset

10 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

1100 VOLTS

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Conductors -Material)	-	500	10% Discount for BIS
Cl-5, Table-1 (i)(Tensile strength)	-	3000	10% Discount for BIS
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	3000	10% Discount for BIS
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	1500	10% Discount for BIS
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	1500	10% Discount for BIS
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iv)(Shrinkage)	-	1500	10% Discount for BIS
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	5000	10% Discount for BIS
Cl-5, Table-1 (vi)(Volume resistivity)	-	3000	10% Discount for BIS
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	500	10% Discount for BIS
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	500	10% Discount for BIS
Cl-7(Armouring)	-	500	10% Discount for BIS
Cl-8(Outer Sheath)	-	500	10% Discount for BIS
Cl-10.3(Tolerance on Thickness of Insulation)	-	1000	10% Discount for BIS
Cl-11(Core Identification)	-	500	10% Discount for BIS
Cl-12(Laying up of Cores)	-	500	10% Discount for BIS
Cl-13(Inner Sheath (Common Covering))	-	500	10% Discount for BIS
Cl-14.1(Armouring- Application)	-	500	10% Discount for BIS
Cl-14.1.2(armour round wires/formed wires)	-	500	10% Discount for BIS
Cl-14.2(Type of Armour)	-	500	10% Discount for BIS
Cl-14.3(Dimensions)	-	1500	10% Discount for BIS
Cl-14.4(Joints)	-	500	10% Discount for BIS
Cl-14.5(Resistance)	-	2500	10% Discount for BIS
Cl-15.3(Thickness of Outer Sheath)	-	2000	10% Discount for BIS
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	1500	10% Discount for BIS
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	1500	10% Discount for BIS
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	1000	10% Discount for BIS
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	2000	10% Discount for BIS
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	2000	10% Discount for BIS
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	2000	10% Discount for BIS
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	2500	10% Discount for BIS
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	2500	10% Discount for BIS
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	2500	10% Discount for BIS
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	2500	10% Discount for BIS
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	3000	10% Discount for BIS
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	3000	10% Discount for BIS
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	3000	10% Discount for BIS
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	4000	10% Discount for BIS
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	4000	10% Discount for BIS
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	2000	10% Discount for BIS
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	1500	10% Discount for BIS
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	2500	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	4000	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	2500	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	2500	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	1500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	2500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	2500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	5000	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	1500	10% Discount for BIS
Cl-17.2(High voltage test)	-	3000	10% Discount for BIS
Cl-17.3(Flammability test)	-	2000	10% Discount for BIS
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.5(Flame retardance test on single cable)	-	3000	10% Discount for BIS
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	10000	`10% Discount for BIS
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	3000	10% Discount for BIS
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	2000	10% Discount for BIS
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	5000	10% Discount for BIS
Cl-16.4 (i)(Cold bend test for outer sheath)	-	1000	10% Discount for BIS
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	1000	10% Discount for BIS
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	5000	10% Discount for BIS
Cl-4(Conductors -Material)	-	500	10% Discount for BIS
Cl-5, Table-1 (i)(Tensile strength)	-	3000	10% Discount for BIS
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	3000	10% Discount for BIS
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	1500	10% Discount for BIS
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	1500	10% Discount for BIS
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	2000	10% Discount for BIS
Cl-5, Table-1 (iv)(Shrinkage)	-	1500	10% Discount for BIS
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	5000	10% Discount for BIS
Cl-5, Table-1 (vi)(Volume resistivity)	-	3000	10% Discount for BIS
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	500	10% Discount for BIS
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	500	10% Discount for BIS
Cl-7(Armouring)	-	500	10% Discount for BIS
Cl-8(Outer Sheath)	-	1000	10% Discount for BIS
Cl-10.3(Tolerance on Thickness of Insulation)	-	1500	10% Discount for BIS
Cl-11(Core Identification)	-	1000	10% Discount for BIS
Cl-12(Laying up of Cores)	-	500	10% Discount for BIS
Cl-13(Inner Sheath (Common Covering))	-	500	10% Discount for BIS
Cl-14.1(Armouring- Application)	-	500	10% Discount for BIS
Cl-14.1.2(armour round wires/formed wires)	-	500	10% Discount for BIS
Cl-14.2(Type of Armour)	-	500	10% Discount for BIS
Cl-14.3(Dimensions)	-	1000	10% Discount for BIS
Cl-14.4(Joints)	-	500	10% Discount for BIS
Cl-14.5(Resistance)	-	2000	10% Discount for BIS
Cl-15.3(Thickness of Outer Sheath)	-	2000	10% Discount for BIS
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	2000	10% Discount for BIS
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	2000	10% Discount for BIS
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	1500	10% Discount for BIS
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	2000	10% Discount for BIS
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	2000	10% Discount for BIS
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	2000	10% Discount for BIS
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	2500	10% Discount for BIS
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	2500	10% Discount for BIS
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	2500	10% Discount for BIS
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	2500	10% Discount for BIS
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	2500	10% Discount for BIS
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	2000	10% Discount for BIS
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	2000	10% Discount for BIS
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	3000	10% Discount for BIS
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	2500	10% Discount for BIS
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	2000	10% Discount for BIS
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	1500	10% Discount for BIS
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	2500	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	4000	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	1500	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	2000	10% Discount for BIS
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	1500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	1500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	1500	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	4000	10% Discount for BIS
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	1500	10% Discount for BIS
Cl-17.2(High voltage test)	-	2500	10% Discount for BIS
Cl-17.3(Flammability test)	-	2500	10% Discount for BIS
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.5(Flame retardance test on single cable)	-	3000	10% Discount for BIS
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	10000	10% Discount for BIS
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	3000	10% Discount for BIS
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	3000	10% Discount for BIS
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	1000	10% Discount for BIS
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	1000	10% Discount for BIS
Cl-16.4 (i)(Cold bend test for outer sheath)	-	1000	10% Discount for BIS
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	1000	10% Discount for BIS
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	5000	10% Discount for BIS

01 May, 2028

-
Included w.e.f 17.02.2026 Exclusion: Cl-17.11 (Test for light transmission for LSHF Sheathed Cables) Cl-17.6 (Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

2000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	200	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	200	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	200	-
9.3(Direction of Lay)	-	100	-
9.4(Multiple layers of wires)	-	100	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	200	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	200	-
12.3 Table 1(Elongation Test- Before Stranding)	-	200	-
12.3 Table 1(Elongation Test- After Stranding)	-	200	-
12.4 Table 1(Resistance of Aluminium wire)	-	200	-
9.2(Lay Ratio 24 wire layer)	-	200	-
9.2(Lay Ratio 18 wire layer)	-	200	-
9.2(Lay Ratio 12 wire layer)	-	200	-
9.2(Lay Ratio 3/6 wire layer)	-	200	-
7.2.1(Sizes)	-	100	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	100	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	100	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	100	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	200	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	200	-
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	200	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	200	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	200	-
9.3(Direction of Lay)	-	100	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	200	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	200	-
12.3 Table 1(Elongation Test- Before Stranding)	-	200	-
12.3 Table 1(Elongation Test- After Stranding)	-	200	-
12.4 Table 1(Resistance of Aluminium wire)	-	200	-
9.2(Lay Ratio 24 wire layer)	-	200	-
9.2(Lay Ratio 18 wire layer)	-	200	-
9.2(Lay Ratio 12 wire layer)	-	200	-
9.2(Lay Ratio 3/6 wire layer)	-	200	-
7.2.1(Sizes)	-	100	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	100	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	100	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	200	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	200	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	200	-
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	100	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	200	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	200	-
9.3(Direction of Lay)	-	100	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	0	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	200	-
12.3 Table 1(Elongation Test- Before Stranding)	-	200	-
12.3 Table 1(Elongation Test- After Stranding)	-	200	-
12.4 Table 1(Resistance of Aluminium wire)	-	200	-
9.2(Lay Ratio 24 wire layer)	-	200	-
9.2(Lay Ratio 18 wire layer)	-	200	-
9.2(Lay Ratio 12 wire layer)	-	200	-
9.2(Lay Ratio 3/6 wire layer)	-	200	-
7.2.1(Sizes)	-	100	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	100	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	100	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	200	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	200	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	200	-

01 May, 2028

-
Included w.e.f 13.10.2025

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	300	25% Discount for BIS
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (mech)(Stranding)	-	0	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	500	25% Discount for BIS
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	500	25% Discount for BIS
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	500	25% Discount for BIS
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	500	25% Discount for BIS
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	300	25% Discount for BIS
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	300	25% Discount for BIS
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	300	25% Discount for BIS
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	300	25% Discount for BIS
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	300	25% Discount for BIS
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	750	25% Discount for BIS
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	750	25% Discount for BIS
13.7.2 (chem)(Mass of Zinc coating)	-	750	25% Discount for BIS
13.7.2 (chem)(Uniformity of Zinc coating)	-	750	25% Discount for BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	300	25% Discount for BIS
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	300	25% Discount for BIS
13.9 (elec)(Surface condition test)	-	0	-
13.10 (elec)(Ultimate breaking load)	-	0	-
13.11 (elec)(Stress-strain test)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	300	25% Discount for BIS
13.7.2 (elec)(Uniformity of Zinc coating)	-	750	25% Discount for BIS
13.7.2 (elec)(Mass of Zinc coating)	-	750	25% Discount for BIS
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	300	25% Discount for BIS
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	300	25% Discount for BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	300	25% Discount for BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	750	25% Discount for BIS
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	750	25% Discount for BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	750	25% Discount for BIS
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	750	25% Discount for BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	300	25% Discount for BIS
13.7.2 (elec)(Uniformity of Zinc coating)	-	750	25% Discount for BIS
13.7.2 (elec)(Mass of Zinc coating)	-	750	25% Discount for BIS
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	300	25% Discount for BIS
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	300	25% Discount for BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	300	25% Discount for BIS
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	500	25% Discount for BIS
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	500	25% Discount for BIS
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	500	25% Discount for BIS
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	500	25% Discount for BIS
10 (elec)(Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
4.1(Resistivity)	-	750	25% Discount for BIS
4.2(Density)	-	500	25% Discount for BIS
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	25% Discount for BIS
4.4(Coefficient of Linear Expansion)	-	500	25% Discount for BIS
5.1(Density)	-	500	25% Discount for BIS
5.2(Coefficient of Linear Expansion)	-	500	25% Discount for BIS
14.2(a), 8.2.1(Sizes)	-	300	25% Discount for BIS
7(FREEDOM FROM DEFECTS)	-	0	-
6.2(zinc Purity)	-	750	25% Discount for BIS
9(Joint in wires)	-	0	-
6.1.1(Aluminum wires shall conform to IS 5484)	-	0	-
6.1.2(The mechanical properties of wire shall comply with the requirements given in Table 2)	-	500	25% Discount for BIS
6.2(It shall conform to and satisfy all the requirements of IS 209)	-	0	-
8.2.2(Calculated resistance)	-	750	25% Discount for BIS
Cl-9.2.5(Welded joint strength)	-	0	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2(Diameter of Steel Wires Before Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires After Stranding)	-	300	25% Discount for BIS
8.1.1 & 13.2 Table 2(Diameter of Steel Wires After Stranding)	-	300	25% Discount for BIS
10(Stranding)	-	0	-
13.3 Table 1(Breaking Load of Aluminium Wires Before Stranding)	-	500	25% Discount for BIS
13.3 Table 2(Breaking Load of Steel Wires Before Stranding)	-	500	25% Discount for BIS
13.3 Table 1(Breaking Load of Aluminium Wires After Stranding)	-	500	25% Discount for BIS
13.3 Table 2(Breaking Load of Steel Wires After Stranding)	-	500	25% Discount for BIS
13.4.1(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.4.1(Ductility by Torsion Test before stranding)	-	500	25% Discount for BIS
13.4.1(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.4.1(Ductility by Torsion Test after stranding)	-	500	25% Discount for BIS
13.5.1(Wrapping Test Aluminium Wires Before Stranding)	-	300	25% Discount for BIS
13.5.1(Wrapping Test Aluminium Wires After Stranding)	-	300	25% Discount for BIS
13.5.2(Wrapping Test Galvanized Steel Wires Before Stranding)	-	300	25% Discount for BIS
13.5.2(Wrapping Test Galvanized Steel Wires After Stranding)	-	300	25% Discount for BIS
13.8 Table-4(Lay Ratio- Aluminium Wire Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	300	25% Discount for BIS
13.8 Table-4(Lay Ratio- Steel Core (6 Wire Layer))	-	300	25% Discount for BIS
13.7(Galvanising test Dip test for uniformity of coating)	-	750	25% Discount for BIS
13.7(Weight of Zinc Coating [g/m²])	-	750	25% Discount for BIS
13.7(Weight of Zinc Coating [g/m²])	-	750	25% Discount for BIS
7.1(Freedom from Defects)	-	0	-
9(Joint in Wire)	-	0	-
13.8 Table-4(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	300	25% Discount for BIS
13.7(Galvanising test Dip test for uniformity of coating)	-	750	25% Discount for BIS

01 May, 2028

-
Included w.e.f 18.08.2025 Exclusion: Cl 13.9 (elec) (Surface condition test), Cl 13.10 (elec) (Ultimate breaking load) , Cl 13.11 (elec) (Stress-strain test)

IS 3419 (1988)

Specification for fittings for rigid non - Metallic (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8 & 5(Visual Examination -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-1, ii(Inside Diameter of Collar for Slip type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-1, iii(Inside Diameter of Ridge for Slip type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-1, iv(Minimum overall length for Slip type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-1, v(Minimum wall thickness for Slip type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-2, ii(Inside Diameter of Collar for Socketed type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-2, iii(Inside Diameter of Ridge for Socketed type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-2, iv(Minimum overall length (a) for Socketed type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-2, v(Minimum overall length (l) for Socketed type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-2, vi(Minimum wall thickness for Socketed type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-3, ii(Inside Diameter of Collar(d6) for Clamp type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-3, iii(Inside Diameter of Collar (d5) for Clamp type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-3, iv(Inside Diameter of Ridge for Clamp type cuplers -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-3, iv(Minimum length for Clamp type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-3, vi(Minimum wall thickness for Clamp type cuplers -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-4, ii(Outside Dameter of Normal type bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-4, iii(Minimum Inside Diameter of Normal Type Bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-4, iv(Radious(R) of Normal Type Bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-4, v(Length (l1) of Normal Type Bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, ii(Outside Dameter of Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, iii(Minimum Inside Diameter of Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, iv(Inside Diameter of collar for Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, v(R- for Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, vi(Y- for Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-5, vii(l2- for Slip type cupling bend -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-6, ii(Inside Diameter of collar for Normal type Elbows -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-6, iii(Length (l) of Normal Type Elbows -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-6, iv(Radious(r) of Normal Type Elbows -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-6, v(Minimum wall thicknes of Elbows -IS:3419)	-	500	25% Discount for BIS
6.2 & 9.1- Table-7, ii(Inside Diameter of Collear for Normal type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-7, iii(Length (l) of Normal type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-7, iv(Radious(r) of Normal type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-7, v( Minimum wall thicknes of Normal type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-8, ii(Inside Diameter of Collear for socketed type Tees - IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-8, iii(a - of socketed type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-8, iv(l - of socketed type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-8, v(Minimum wall thicknes of socketed type Tees -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, ii(B - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, iii(C - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, iv(D - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, v(E - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, vi(F(Max) - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, vii(F(Min) - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, viii(G - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
6.2 & 9.1- Table-9, ix(t - of spout Type Circular Boxes -IS:3419)	-	200	25% Discount for BIS
10(Resistance to Heat -IS:3419)	-	1000	25% Discount for BIS
11(Resistance to Burning - IS 3419)	-	1000	25% Discount for BIS
12(Moisture Absorption - IS 3419)	-	500	25% Discount for BIS
13.2 &13.3(Resistance to chemival action in Acid solution - IS 3419)	-	1500	25% Discount for BIS
13.2 &13.3(Resistance to chemival action in Alkaline solution - IS 3419)	-	1500	25% Discount for BIS
14.1(Copper Test - IS 3419)	-	1000	25% Discount for BIS
15, 15.3(Resistance to Oil - IS 3419)	-	1000	25% Discount for BIS
15,15.4(Resistance to Oil - IS 3419)	-	1000	25% Discount for BIS
16- Appendix-A(Resistance to Impact -IS 3419)	-	500	25% Discount for BIS
17.2(Electric Strength - IS 3419)	-	500	25% Discount for BIS
17.3(Insulation Resistance - IS 3419)	-	500	25% Discount for BIS
Cl.7.1(Marking)	-	500	25% Discount for BIS
Cl.7.1(Construction)	-	250	25% Discount for BIS
Cl. 5(Construction)	-	250	25% Discount for BIS
Cl. 5(Construction)	-	250	25% Discount for BIS
Cl.5.3(Construction)	-	250	25% Discount for BIS
Cl.5.3(Construction)	-	250	25% Discount for BIS
(Cl.6) Table 9(Dimensions A)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions B)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions C)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions D)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions E)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions F)	-	50	25% Discount for BIS
(Cl.6) Table 9(Dimensions G)	-	500	25% Discount for BIS
(Cl.6) Table 9(Dimensions t)	-	500	25% Discount for BIS
Cl. 10(Resistance to Heat)	-	1000	25% Discount for BIS
Cl. 11(Resistance to Burning)	-	500	25% Discount for BIS
Cl. 12(Moisture Absorption Test)	-	500	25% Discount for BIS
Cl.13(Resistance to Chemical Action)	-	1500	25% Discount for BIS
Cl.14(Copper Test)	-	1000	25% Discount for BIS
Cl. 15(Resistance to Oil)	-	1000	25% Discount for BIS
Cl. 15(Resistance to Oil)	-	1000	25% Discount for BIS

01 May, 2028

-
-

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	500	25% Discount for BIS
6.1(Marking, IS 9537-2)	-	500	25% Discount for BIS
6.1(Marking, IS 9537-2)	-	500	25% Discount for BIS
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	500	25% Discount for BIS
6.2(Marking, IS 9537-2)	-	500	25% Discount for BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	25% Discount for BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	500	25% Discount for BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500	25% Discount for BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	500	25% Discount for BIS
7.4(Screw threads, IS 9537-2)	-	500	25% Discount for BIS
8.1(Construction, Cl. 8 of IS 9537-1)	-	250	25% Discount for BIS
8.2(Construction, IS 9537-2)	-	250	25% Discount for BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1000	25% Discount for BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1500	25% Discount for BIS
13(External Influences, IS 9537-2)	-	500	25% Discount for BIS
Cl 13.4.5(External Influence ( Outside tube))	-	500	25% Discount for BIS
Cl 13.4.6(External Influence ( Inside tube))	-	500	25% Discount for BIS
7.1(Dimensions)	-	500	25% Discount for BIS

01 May, 2028

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	500	25% Discount for BIS
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	300	25% Discount for BIS
6.3(Standard Mark on Conduit)	-	300	25% Discount for BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	500	25% Discount for BIS
7.1.1 Table-2(Length of Socket end)	-	300	25% Discount for BIS
7.1.2(Maximum and minimum outside diameter of conduit)	-	500	25% Discount for BIS
7.2(Minimum inside diameter of conduit)	-	500	25% Discount for BIS
7.3(Length of conduit)	-	300	25% Discount for BIS
7.4(Unifomity of The wall Thickness)	-	500	25% Discount for BIS
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	250	25% Discount for BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000	25% Discount for BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	2500	25% Discount for BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
10(Resistance to Heat -Ball presure test)	-	1000	25% Discount for BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
12(3 Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
12(3 Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
10.0(Resistance to Heat -Ball presure test)	-	1000	25% Discount for BIS
9.5 Fig.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1500	25% Discount for BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	2500	25% Discount for BIS
9.3(Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980)	-	1000	25% Discount for BIS
9.3(Compression Test at Full force applied (On load))	-	1000	25% Discount for BIS
9.2(Bending Test At Low Temp (-5 ±2°C))	-	1000	25% Discount for BIS
9.2(Bending Test At Room Temp)	-	500	25% Discount for BIS
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	250	25% Discount for BIS
7.4(Unifomity of The wall Thickness)	-	250	25% Discount for BIS
7.3(Length of conduit)	-	300	25% Discount for BIS
7.2 Fig.3(Minimum inside diameter of conduit)	-	500	25% Discount for BIS
7.1.2 Fig.2(Minimum outside diameter of conduit)	-	500	25% Discount for BIS
7.1.2 Fig.1(Maximum outside diameter of conduit)	-	500	25% Discount for BIS
7.1.1 Table-2(Length of Socket end)	-	500	25% Discount for BIS
7.1.1 Fig.8(Maximum inside diameter of socket)	-	500	25% Discount for BIS
7.1.1 Fig.7(Maximum outside diameter of socket)	-	500	25% Discount for BIS
6.3(Standard Mark on Conduit)	-	300	25% Discount for BIS
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	300	25% Discount for BIS
6.1 - d(Marking)	-	500	25% Discount for BIS
6.1 - c(Marking)	-	500	25% Discount for BIS
6.1 - b(Marking)	-	500	25% Discount for BIS
6.1 - a(Marking)	-	500	25% Discount for BIS

01 May, 2028

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	200	25 % Discount for BIS
6.5(Size of messenger conductor )	-	200	25 % Discount for BIS
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	500	25 % Discount for BIS
7.3(Tolerance on thickness of insulation )	-	500	25 % Discount for BIS
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	200	25 % Discount for BIS
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	500	25 % Discount for BIS
9.3(Direction of lay)	-	200	25 % Discount for BIS
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	25 % Discount for BIS
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	25 % Discount for BIS
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1500	25 % Discount for BIS
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	25 % Discount for BIS
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	25 % Discount for BIS
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1500	25 % Discount for BIS
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	25 % Discount for BIS
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	25 % Discount for BIS
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	2500	25 % Discount for BIS
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	2500	25 % Discount for BIS
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	25 % Discount for BIS
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	25 % Discount for BIS
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	25 % Discount for BIS
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	25 % Discount for BIS
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	4000	25 % Discount for BIS
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	25 % Discount for BIS
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	25 % Discount for BIS
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	25 % Discount for BIS
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	25 % Discount for BIS
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	25 % Discount for BIS
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1500	25 % Discount for BIS
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1500	25 % Discount for BIS
10.1 g)(High voltage test - IS10810:Part 45)	-	500	25 % Discount for BIS
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	25 % Discount for BIS
11.4(Bending Test on the Completed Cable ( Optional))	-	1000	25 % Discount for BIS
10.1 d) iii)(Carbon Black Content)	-	2500	25 % Discount for BIS
6.1(Construction of phase conductor)	-	0	-
6.1(Number of wires (phase conductor))	-	0	-
6.1(Construction of Street Lighting conductor)	-	0	-
6.1(Number of wires (Street Lighting conductor))	-	200	25 % Discount for BIS
12.1(Manufacturer's Identification)	-	500	25 % Discount for BIS
12.2(Cable Identification)	-	0	-

01 May, 2028

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	0	-
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
6(ARMOURING)	-	0	-
7(OUTER SHEATH)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	500	25 % Discount for BIS
9.3(Thickness of Insulation - Minimum)	-	500	25 % Discount for BIS
9.4(Application of Insulation)	-	200	25 % Discount for BIS
10.1(Core Identification)	-	200	25 % Discount for BIS
10.2(Core Identification- Neutral)	-	200	25 % Discount for BIS
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	200	25 % Discount for BIS
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	500	25 % Discount for BIS
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	1000	25 % Discount for BIS
13.1.3(Armouring: Direction of Lay )	-	200	25 % Discount for BIS
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	25 % Discount for BIS
13.3(Armouring : Dimensions -Formed wire )	-	500	25 % Discount for BIS
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	1500	25 % Discount for BIS
13.6 a)(ARMOURING: Tensile Strength)	-	500	25 % Discount for BIS
13.6 b)(ARMOURING: Elongation )	-	500	25 % Discount for BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	25 % Discount for BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	25 % Discount for BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	25 % Discount for BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	25 % Discount for BIS
13.6 g)(ARMOURING: Resistivity)	-	1500	25 % Discount for BIS
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	500	25 % Discount for BIS
14.3(Thickness of outer sheath - minimum)	-	500	25 % Discount for BIS
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	25 % Discount for BIS
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	500	25 % Discount for BIS
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	500	25 % Discount for BIS
15.1 a) iii)(Wrapping test (for aluminium))	-	500	25 % Discount for BIS
15.1 a) iv)(Resistance test - Main conductor)	-	1500	25 % Discount for BIS
15.1 a) iv)(Resistance test - Neutral conductor)	-	1500	25 % Discount for BIS
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	500	25 % Discount for BIS
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	500	25 % Discount for BIS
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2500	25 % Discount for BIS
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2500	25 % Discount for BIS
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	25 % Discount for BIS
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	25 % Discount for BIS
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	500	25 % Discount for BIS
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	25 % Discount for BIS
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	4000	25 % Discount for BIS
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	500	25 % Discount for BIS
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	500	25 % Discount for BIS
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2500	25 % Discount for BIS
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2500	25 % Discount for BIS
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2500	25 % Discount for BIS
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2500	25 % Discount for BIS
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2500	25 % Discount for BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	25 % Discount for BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	25 % Discount for BIS
15.1 e) v) (Sheath : Hot deformation)	-	1000	25 % Discount for BIS
15.1 e) vi) (Sheath : Heat shock test)	-	500	25 % Discount for BIS
15.1 e) vii) (Sheath : Thermalstability)	-	1000	25 % Discount for BIS
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1500	25 % Discount for BIS
16.2(HIGH VOLTAGE TEST )	-	500	25 % Discount for BIS
16.3(FLAMMABILITY TEST : Period of Burning )	-	1500	25 % Discount for BIS
16.3(FLAMMABILITY TEST : Unaffected length )	-	1500	25 % Discount for BIS
16.9(Oxygen Index Test)	-	2500	25 % Discount for BIS
16.1(Flame Retardance Test on Single Cables)	-	1000	25 % Discount for BIS
16.11(Flame Retardance Test on Bunched Cables)	-	0	-
16.13(Test for Halogen Acid Gas Evolution)	-	3000	25 % Discount for BIS
16.14(Temperature Index)	-	2500	25 % Discount for BIS
17.1(Manufacturer'. identification)	-	200	25 % Discount for BIS
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	500	25 % Discount for BIS
15.4 (b)(Cold impact)	-	500	25 % Discount for BIS
Table 1(Ageing in air oven - Elongation on Insulation)	-	2500	25 % Discount for BIS
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2500	25 % Discount for BIS
Table 1(Ageing in air oven - Elongation on Insulation)	-	2500	25 % Discount for BIS
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2500	25 % Discount for BIS
Table 4(Copper purity test)	-	0	-
Cl No. 16.15(Smoke density test)	-	2500	25 % Discount for BIS
Table 2(Cold Impact test for Outer sheath)	-	500	25 % Discount for BIS
Table 2(Cold bend test for Outer sheath)	-	500	25 % Discount for BIS
Cl 16(Halogen Acid Gas Test)	-	3000	25 % Discount for BIS
Cl 16(Halogen Acid Gas Test)	-	3000	25 % Discount for BIS
Cl 16(Halogen Acid Gas Test)	-	3000	25 % Discount for BIS
Cl.8(Conductor)	-	0	-
Cl.8(Conductor)	-	0	-
Cl.8(Conductor)	-	0	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	500	25 % Discount for BIS
Cl.15.4(Cold Impact Test (For outer sheath))	-	500	25 % Discount for BIS
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1500	25 % Discount for BIS

01 May, 2028

-
Exclusion: 16.11 (Flame Retardance Test on Bunched Cables), Table 4 (Copper purity test), Cl No. 16.15 (Smoke density test)

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	200	25 % Discount for BIS
6.2(MATERIALS : ARMGURING)	-	200	25 % Discount for BIS
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	500	25 % Discount for BIS
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	500	25 % Discount for BIS
9.4(INSULATION : Application of Insulation)	-	200	25 % Discount for BIS
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	200	25 % Discount for BIS
11.2(LAYING UP OF CORES)	-	200	25 % Discount for BIS
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	500	25 % Discount for BIS
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	500	25 % Discount for BIS
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	500	25 % Discount for BIS
13.1.3(ARMOURING : Direction of lay )	-	200	25 % Discount for BIS
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	25 % Discount for BIS
13.3(Armouring : Dimensions -Formed wire )	-	500	25 % Discount for BIS
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	1000	25 % Discount for BIS
13.5.2(ARMOURING : Resistance)	-	1000	25 % Discount for BIS
13.6 a)(ARMOURING: Tensile Strength)	-	500	25 % Discount for BIS
13.6 b)(ARMOURING: Elongation )	-	500	25 % Discount for BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	25 % Discount for BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	25 % Discount for BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	25 % Discount for BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	25 % Discount for BIS
13.6 g)(ARMOURING: Resistivity)	-	1000	25 % Discount for BIS
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	500	25 % Discount for BIS
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	25 % Discount for BIS
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	500	25 % Discount for BIS
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	500	25 % Discount for BIS
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	500	25 % Discount for BIS
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	500	25 % Discount for BIS
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	25 % Discount for BIS
15.1 a) 4)(Resistance test - Neutral conductor )	-	500	25 % Discount for BIS
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	500	25 % Discount for BIS
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	500	25 % Discount for BIS
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	500	25 % Discount for BIS
15.1 d)1)(Physical tests for sheath : Elongation )	-	500	25 % Discount for BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2500	25 % Discount for BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2500	25 % Discount for BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2500	25 % Discount for BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2500	25 % Discount for BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2500	25 % Discount for BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2500	25 % Discount for BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2500	25 % Discount for BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2500	25 % Discount for BIS
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	25 % Discount for BIS
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	25 % Discount for BIS
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	25 % Discount for BIS
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	25 % Discount for BIS
15.1 d)4)(Hot deformation : Insulation )	-	1000	25 % Discount for BIS
15.1 d)4)(Hot deformation : Sheath )	-	1000	25 % Discount for BIS
15.1 d)5)( Loss of mass in air oven- Insulation )	-	2500	25 % Discount for BIS
15.1 d)5)( Loss of mass in air oven- sheath )	-	2500	25 % Discount for BIS
15.1 d)6)(Heat shock test- Insulation )	-	500	25 % Discount for BIS
15.1 d)6)(Heat shock test- sheath )	-	500	25 % Discount for BIS
15.1 d)7)(Thermal stability- insulation )	-	1000	25 % Discount for BIS
15.1 d)7)(Thermal stability- Sheath )	-	1000	25 % Discount for BIS
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1500	25 % Discount for BIS
15.1 e)(Insulation resistance test : IR Constant )	-	1500	25 % Discount for BIS
15.1 f)(High voltage test ( water immersion test ))	-	2500	25 % Discount for BIS
15.1 g)(High voltage test at room temperature)	-	500	25 % Discount for BIS
15.1 g)(High voltage test at room temperature)	-	500	25 % Discount for BIS
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	25 % Discount for BIS
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	25 % Discount for BIS
15.4 b)(Cold impact test- Insulation ( Optional test))	-	500	25 % Discount for BIS
15.4 b)(Cold impact test- Sheath ( Optional test))	-	500	25 % Discount for BIS
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	1000	25 % Discount for BIS
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	500	25 % Discount for BIS
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	2500	25 % Discount for BIS
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	4000	25 % Discount for BIS
16.4(Flammability Test)	-	1000	25 % Discount for BIS
16.5(Oxygen Index Test)	-	2500	25 % Discount for BIS
16.6(Flame Retardance Test on Single Cables)	-	1000	25 % Discount for BIS
16.9(Test for Halogen Acid Gas Evolution)	-	3000	25 % Discount for BIS
16.1(Temperature Index)	-	2500	25 % Discount for BIS
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	200	25 % Discount for BIS
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1500	25 % Discount for BIS
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	25 % Discount for BIS
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1500	25 % Discount for BIS
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	25 % Discount for BIS
16.4(Flammability Test- Un affected portion)	-	1500	25 % Discount for BIS
16.4(Flammability Test- Period of Burning)	-	1500	25 % Discount for BIS
9.3(Minimum Thickness of Reduce core insulation)	-	500	25 % Discount for BIS
9.2(Thickness of Reduce core insulation)	-	500	25 % Discount for BIS
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	200	25 % Discount for BIS
Cl No. 16.10(Smoke density test)	-	2500	25 % Discount for BIS
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	200	25 % Discount for BIS
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2500	25 % Discount for BIS

01 May, 2028

-
Exclusion: 16.7 (Flame Retardance Test on Bunched Cables), Cl No. 16.8 (Test for specific optical density of smoke), Table 4 (Copper purity test)

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

450/750 V

32500.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	4500.00	30% Discount for BIS
10.4(Flammability test- Unaffected portion)	-	750.00	30% Discount for BIS
10.4(Flammability test-Burning after flame removal)	-	750.00	30% Discount for BIS
table 1 e) 3) (IR constant- max. Temp)	-	1500.00	30% Discount for BIS
table 1 e) 3) (IR constant- Room temp )	-	500.00	30% Discount for BIS
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	1500.00	30% Discount for BIS
table 1 e) 3) (Volume Resistivity - Room temp )	-	500.00	30% Discount for BIS
10.2(HV (room temperature))	-	500.00	30% Discount for BIS
10.1(HV (water immersion))	-	2500.00	30% Discount for BIS
10.8(Smoke density rating)	-	2500.00	30% Discount for BIS
10.6(Halogen evolution)	-	3000.00	30% Discount for BIS
10.7(Temperature index)	-	2500.00	30% Discount for BIS
10.5(Oxygen index)	-	2500.00	30% Discount for BIS
Table 1 iii) d) 9)(Cold impact for sheath)	-	500.00	30% Discount for BIS
Table 1 iii) d) 8)(Cold bend for sheath)	-	500.00	30% Discount for BIS
Table 1 iii) c) 9)(Cold impact for insulation)	-	500.00	30% Discount for BIS
Table 1 iii) c) 8)(Cold bend for insulation)	-	500.00	30% Discount for BIS
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000.00	30% Discount for BIS
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1000.00	30% Discount for BIS
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000.00	30% Discount for BIS
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000.00	30% Discount for BIS
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500.00	30% Discount for BIS
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500.00	30% Discount for BIS
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500.00	30% Discount for BIS
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500.00	30% Discount for BIS
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	2500.00	30% Discount for BIS
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	2500.00	30% Discount for BIS
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	2500.00	30% Discount for BIS
Table 1 iii) d) 3)(Sheath- TS variation)	-	2500.00	30% Discount for BIS
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	2500.00	30% Discount for BIS
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2500.00	30% Discount for BIS
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500.00	30% Discount for BIS
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500.00	30% Discount for BIS
8.3(Thickness of Sheath)	-	500.00	30% Discount for BIS
5.3(Thickness of Insulation)	-	500.00	30% Discount for BIS
9(Overall dimensions)	-	200.00	30% Discount for BIS
10.11(Per sulphate test (for tinned Cu cable only))	-	2500.00	30% Discount for BIS
4.2(Conductor resistance test)	-	1100.00	30% Discount for BIS
4.1(Tensile test (for Al)-Before Stranding)	-	500.00	30% Discount for BIS
4.1(Annealing test (for copper))	-	500.00	30% Discount for BIS
4.1(Wrapping test (for Al))	-	500.00	30% Discount for BIS
9.1(Ovality)	-	200.00	30% Discount for BIS
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500.00	30% Discount for BIS
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500.00	30% Discount for BIS
11(Identification)	-	0.00	-
13(Cable code)	-	0.00	-
11.2(Legibility)	-	0.00	-
11.1(Durability)	-	200.00	30% Discount for BIS
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
Cl. 8.2(Application of Sheath)	-	0.00	-
Cl.19.1.4(Assembly of Cores)	-	0.00	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0.00	--
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0.00	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0.00	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0.00	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0.00	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0.00	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0.00	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0.00	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0.00	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	0.00	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	0.00	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	0.00	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	0.00	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0.00	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0.00	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0.00	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	0.00	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0.00	-
16.2(Tests)	-	0.00	--
16.1(Construction)	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0.00	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0.00	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	200.00	30% Discount for BIS
(Cl.16.1) (Cl.19.1)(Conductor)	-	0.00	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0.00	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0.00	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	0.00	-
12(CONSTRUCTION Core Identification)	-	200.00	30% Discount for BIS
8.1(Sheath Material )	-	0.00	--
7(Binder Tape)	-	0.00	30% Discount for BIS
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	100.00	30% Discount for BIS
5.2(Application )	-	0.00	--
4.1(Conductor - Material)	-	0.00	--
4.4(Joints in Conductor)	-	0.00	--
12.0(Core identification)	-	100.00	30% Discount for BIS
10.11(Persulphate Test)	-	2500.00	30% Discount for BIS
4.1(Material)	-	0.00	30% Discount for BIS
5(INSULATION)	-	0.00	--
6(FILLER)	-	0.00	--
7(BINDER TAPE)	-	0.00	--
8(SHEATH)	-	0.00	--
9(OVERALL DIMENSIONS)	-	200.00	30% Discount for BIS
10.1(High Voltage Test (Water Immersion Test))	-	2500.00	30% Discount for BIS
10.2(High Voltage Test (at Room Temperature))	-	500.00	30% Discount for BIS
10.3(Spark Test)	-	0.00	--
10.4(Flammability Test)	-	1500.00	30% Discount for BIS
10.5(Oxygen Index Test)	-	2500.00	30% Discount for BIS
10.6(Test for Halogen Acid Gas Evolution)	-	3000.00	30% Discount for BIS
10.7(Test for Temperature Index)	-	2500.0	30% Discount for BIS
10.8(Smoke Density Rating)	-	2500.00	30% Discount for BIS
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	4500.00	30% Discount for BIS
10.1(Flex Test)	-	0.00	--
11(IDENTIFICATION)	-	500.00	30% Discount for BIS
12(CORE IDENTIFICATION)	-	500.00	30% Discount for BIS
13(CABLE CODE)	-	200.00	30% Discount for BIS
15(PACKING AND MARKING)	-	0.00	--
Table 1 iii) d) 4)(Cracks Observed)	-	500.00	30% Discount for BIS
Table 1 iii) c) 4)(Cracks Observed)	-	500.00	30% Discount for BIS
Table 1 iii) c) 3)(Elongation (After ageing))	-	2500.00	30% Discount for BIS
Table 1 iii) c) 3)(TS variation)	-	2500.00	30% Discount for BIS
4.1(Tensile test (for Al)- After Stranding)	-	500.00	30% Discount for BIS
6.2(Filler)	-	0.00	--
6.1(Filler)	-	0.00	--
5.1(Insulation)	-	0.00	--
4.4(Joints in Conductor)	-	0.00	-
4.1(Conductor - Material)	-	0.00	-
10.11(Persulphate Test )	-	2500.00	30% Discount for BIS
Table 2, IS 8130(No fo wire in a conductor)	-	200.00	30% Discount for BIS
8.3(Minimum thickness of Sheath)	-	500.00	30% Discount for BIS
8.3(Avarage thickness of Sheath)	-	500.00	30% Discount for BIS
5.3(Minimum thickness of insulation)	-	500.00	30% Discount for BIS
5.3(Avarage thickness of insulation)	-	500.00	30% Discount for BIS
10.3(Spark test)	-	0.00	-
table 1, 4.2(insulation resistance test)	-	1500.00	30% Discount for BIS
5.4(Mechanical properties before and after ageing)	-	5000.00	30% Discount for BIS
10.1(HV (water immersion))	-	2500.00	30% Discount for BIS
Table 1(Category Code)	-	0.00	--
Table 1 iii) c) 3)(Elongation variation)	-	2500.00	30% Discount for BIS
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	2500.00	30% Discount for BIS
4, IS 8130(Construction of conductor)	-	0.00	--
4.2(Electrical Resistance)	-	1500.00	30% Discount for BIS
10.3(Spark Test)	-	0.00	--

01 May, 2028

-
Exclusion: Table 4 (Copper purity test)

Bureau of Indian Standards

The National Standards Body of India

AADHAR TESTING SOLUTIONS LLP, GHAZIABAD

First Floor, Plot no. 02, Gyani Compound, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201005

8810500700 mkvishnoi10@gmail.com

Scope List