BIS - LIMS (Laboratory Information Management System)

JAWAHARLAL NEHRU ALUMINIUM RESEARCH DEVELOPMENT AND DESIGN CENTER

opp Wadi Police Station, Amravati Rd, Wadi, Nagpur, Nagpur, Maharashtra, 440023

9980574024 immanuelkola@jnarddc.gov.in

Scope List

Reset

10 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

EC Grade

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	1200	-
Cl-9(Ultimate tensile strength and elongation)	-	1000	-
Cl-6.2(Chemical analysis of the material)	-	1200	-
Cl-10.1(Resistivity)	-	3000	-
Cl-10.1(electrical conductivity)	-	0	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	3000	-
Cl-11(Dimensions)	-	1000	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	1000	-
CL 11(DIMENSIONS)	-	1000	-
9(Elongation)	-	1000	-

24 Apr, 2028

-
-

IS 9997 (2023)

ALUMINIUM ALLOY REDRAW RODS FOR ELECTRICAL PURPOSES - SPECIFICATION

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1, Table-2 (i)(Silicon)	-	1200	-
Cl-7.1, Table-2 (ii)(Iron)	-	1200	-
Cl-7.1, Table-2 (iii)(Copper)	-	1200	-
Cl-7.1, Table-2 (iv)(Manganese)	-	1200	-
Cl-7.1, Table-2 (v)(Magnesium)	-	1200	-
Cl-7.1, Table-2 (vi)(Chromium)	-	1200	-
Cl-7.1, Table-2 (viii)(Boron)	-	1200	-
Cl-7.1, Table-2 (ix)(Vanadium + Titanium)	-	1200	-
Cl-7.1, Table-2 (x)(Other each)	-	1200	-
Cl-7.1, Table-2 (xi)(Others total)	-	1200	-
Cl-7.1, Table-2 (xii)(Aluminium)	-	0.00	-
Cl-8.1, Table-3(UTS (MPa))	-	1000	-
Cl-8.1, Table-3(Elongation (%) - On 250 mm gauge length)	-	1000	-
Cl-8.1, Table-3(Resistivity (micro ohm.cm) at 20 oC)	-	3000	-
Cl-9(Electrical resistivity)	-	3000	-
Cl-7.1, Table-2 (vii)(Zinc)	-	1200	-
Cl-10(Diameter and Permissible Variations)	-	1000	-

24 Apr, 2028

-
-

IS 1285 (2002)

Wrought aluminium and aluminium alloys - Extruded round tube and hollow sections for general engineering purposes - Specification (Third Revision)

2200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7/a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube - outside Dia or Inside Dia)	-	1000	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube - outside Dia or Inside Dia)	-	1000	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube - Wall thickness)	-	1000	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube - Allowable Deviation of Mean Diameter from Specified Diameter (Size Tolerance))	-	1000	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube - Allowabte Deviation of Diameter at Any Point from Specified Diameter (Ovality Tolcrance))	-	1000	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube -Straightness)	-	0	-
7 of IS 1285 /a) Extruded round tube IS 2673(DIMENSIONS AND TOLERANCE-Extruded round tube -Length)	-	1000	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -SPECIFIED WIDTH or WIDTH ACROSS FLATS)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections - Specified WIDTH or WIDTH ACROSS FLATS)	-	1000	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections - Specified WIDTH or WIDTH ACROSS FLATS)	-	1000	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -SPECIFIED Wall thickness)	-	1000	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections - Lengths)	-	1000	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -Straightness)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -Straightness)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -Flatness)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -Twist)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(DIMENSIONS AND TOLERANCE-Extruded hollow sections -Twist)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(Extruded hollow sections -Twist -Permissible Twist in Total Length of piece- degrees)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(Extruded hollow sections -Twist -Permissible Twist in Total Length of piece- At extremetiy)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477("Extruded hollow sections -Twist -ALLOWABLE DEVIATION FROM SPECIFIED ANGLE, DEGREES")	-	0	-
8(Chemical Composition - IS 1285)	-	1200	-
9(Mechanical Comp[osition -IS 1285)	-	1200	-
As per Clause 8 Table !(Aluminium)	-	1200	-
As per Clause 8 Table !(Copper)	-	1200	-
As per Clause 8 Table !(Magnesium)	-	1200	-
As per Clause 8 Table !(Silicon)	-	1200	-
As per Clause 8 Table !(Iron)	-	1200	-
As per Clause 8 Table !(Manganese)	-	1200	-
As per Clause 8 Table !(Zinc)	-	1200	-
As per Clause 8 Table !(Titanium)	-	1200	-
As per Clause 8 Table !(Chromium)	-	1200	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(Extruded hollow sections -Twist -Permissible Twist, Maximum allowable in Total Length- degrees)	-	0	-
7 of IS 1285 / b) Extruded hollow sections IS 6477(Extruded hollow sections -Twist -Permissible Twist Maximum allowable in Total Length- At extremetiy)	-	0	-

24 Apr, 2028

-
-

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1, Clause - 5.1(Copper)	-	1200	-
Table-1, Clause - 5.1(Magnesium)	-	1200	-
Table-1, Clause - 5.1(Silicon)	-	1200	-
Table-1, Clause - 5.1(Iron)	-	1200	-
Table-1, Clause - 5.1(Zinc)	-	1200	-
Table-1, Clause - 5.1(Titanium)	-	1200	-
Table-1, Clause - 5.1(Chromium)	-	1200	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	1200	-
Table-1, Clause - 5.1(Manganese)	-	1200	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	1000	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	1000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	1000	-
7(Dimension - IS 3965)	-	1000	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	0	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	0	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	1200	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	1200	-

24 Apr, 2028

-
-

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	1000	-
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	0	-
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	1200	-
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	1200	-
7(Dmension And Tolerances)	-	1000	-

24 Apr, 2028

-
-

IS 11890 (1987)

Specification for high purity primary aluminium ingots for remelting for special applications

1200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.6.1,Table no. 1(i)(Aluminium,)	-	0.00	-
Cl. No.6.1,Table no. 1(ii)(Copper)	-	1200	-
Cl. No.6.1,Table no. 1(iii)(Silicon)	-	1200	-
Cl. No.6.1,Table no. 1(iv)(Iron)	-	1200	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	1200	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	1200	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	1200	-
Cl. No.6.1,Table no. 1(viii)(Titanium + Vanadium)	-	1200	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	1200	-
Cl. No.6.1,Table no. 1(x)(Other elements)	-	1200	-

24 Apr, 2028

-
-

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(chemical composition)	-	1200	-
6.1 table 2(0.2% proof strength)	-	1000	-
6.1 table 2(tensile strength)	-	1000	-
6.1 table 2(Elongation)	-	1000	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Copper)	-	1200	-
5.1, Table 1(Magnesium)	-	1200	-
5.1, Table 1(Silicon)	-	1200	-
5.1, Table 1(Iron)	-	1200	-
5.1, Table 1(Mangnese)	-	1200	-
5.1, Table 1(Zinc)	-	1200	-
5.1, Table 1(Titanium and /or other grain refining element)	-	1200	-
5.1, Table 1(Chromium)	-	1200	-
5.1, Table 1(Vanadium)	-	1200	-
8(Dimensions & Tolerances)	-	1000	-

24 Apr, 2028

-
-

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

2200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	1200	-
5.1 table 2(0.2% proof strength)	-	1000	-
5.1 table 2(Tensile strength)	-	1000	-
5.1 table 2(Elongation)	-	1000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	1200	-
9.1(Tensile test)	-	1000	-

24 Apr, 2028

-
-

IS 4026 (2007)

Aluminium ingots, billets and wire bars (Ec Grade) (Fourth Revision)

1200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 8 Table 1(CHEMICAL COMPOSITION 1) Aluminium ,& min)	-	1200	-
Clause 8 Table 1(2) Silicon)	-	1200	-
Clause 8 Table 1(Chemical Composition 3) Iron)	-	1200	-
Clause 8 Table 1(Chemical Composition 4) Copper)	-	1200	-
Clause 8 Table 1(Chemical Composition 5) Titanium+ Vanadiun)	-	1200	-
Clause 8 Table 1(Chemical Composition 6) Manganese, Zirconium and Chromium)	-	1200	-

24 Apr, 2028

-
-

IS 2590 (1987)

Specification for primary aluminium ingots for remelting for general engineering purposes (Second Revision)

1200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Chemical composition )	-	1200	-
Table-1, Clause - 6.1.1(Copper)	-	1200	-
Table-1, Clause - 6.1.1(Iron)	-	1200	-
Table-1, Clause - 6.1.1(Magnesium)	-	1200	-
Table-1, Clause - 6.1.1(Manganese)	-	1200	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	1200	-
Table-1, Clause - 6.1.1(Silicon)	-	1200	-
Table-1, Clause - 6.1.1(Vanadium)	-	1200	-
Table-1, Clause - 6.1.1(Zinc)	-	1200	-
Table-1, Clause - 6.1.1(Other elements (each))	-	1200	-
Table-1, Clause - 6.1.1(Others Total)	-	1200	-
Table-1, Clause - 6.1.1(Aluminium)	-	0	-

24 Apr, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

JAWAHARLAL NEHRU ALUMINIUM RESEARCH DEVELOPMENT AND DESIGN CENTER

opp Wadi Police Station, Amravati Rd, Wadi, Nagpur, Nagpur, Maharashtra, 440023

9980574024 immanuelkola@jnarddc.gov.in

Scope List