BIS - LIMS (Laboratory Information Management System)

SHRI KRISHNA TEST HOUSE PVT LTD (142)

Plot No.142, Sec-G, Bawana-II, DSIIDC, Bhorgarh industrial area New Delhi, Delhi, North, Delhi, 110040

9266808773 SKTHPL142@GMAIL.COM

Scope List

Reset

60 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 21 (2025)

Wrought Aluminium and Aluminium Alloys for Manufacture of Utensils - Specification (Fifth Revision)

ALL

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	7500	-
Cl-5.1(Material)	-	7500	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	7500	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	7500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	7500	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	7500	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	7500	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	7500	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	7500	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	7500	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	7500	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	7500	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	7500	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	7500	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	7500	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	7500	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	7500	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	7500	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	7500	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	7500	-
Cl 5.4(Lead)	-	7500	-
Cl 5.4(Cadmium)	-	7500	-
Cl 5.4(Arsenic)	-	7500	-
Cl-7(Dimension)	-	7500	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	7500	-

13 May, 2028

-
Included w.e.f 18.08.2025

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	10000	-
6(Classification- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.3(Marking- IS 302-1)	-	10000	-
7.4(Marking- IS 302-1)	-	10000	-
7.6(Marking- IS 302-1)	-	10000	-
7.7(Marking- IS 302-1)	-	10000	-
7.8(Marking- IS 302-1)	-	10000	-
7.11(Marking- IS 302-1)	-	10000	-
7.12(Marking- IS 302-1)	-	10000	-
7.13(Marking- IS 302-1)	-	10000	-
7.14(Marking- IS 302-1)	-	10000	-
7.15(Marking- IS 302-1)	-	10000	-
7.101(Marking)	-	10000	-
8( Protection Against Electric Shock, IS 302-1)	-	10000	-
10(Power Input and Current, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	10000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	10000	-
14(Transient Over Voltages, IS 302-1)	-	10000	-
15.1(Moisture Resistance, IS 302-1)	-	10000	-
15.2(Moisture Resistance, IS 302-1)	-	10000	-
15(Moisture Resistance, IS 302-1)	-	10000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	10000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	10000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	10000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	10000	-
19.7(Abnormal Operation, IS 302-1)	-	10000	-
19.8(Abnormal Operation, IS 302-1)	-	10000	-
19.9(Abnormal Operation, IS 302-1)	-	10000	-
19.1(Abnormal Operation, IS 302-1)	-	10000	-
19.101(Abnormal Operation)	-	10000	-
19.102(Abnormal Operation)	-	10000	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	10000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	10000	-
20.101(Stability & Mechanical Hazards)	-	10000	-
20.102(Stability & Mechanical Hazards)	-	10000	-
20.103(Stability & Mechanical Hazards)	-	10000	-
20.104(Stability & Mechanical Hazards)	-	10000	-
20.105(Stability & Mechanical Hazards)	-	10000	-
20.106(Stability & Mechanical Hazards)	-	10000	-
20.107(Stability & Mechanical Hazards)	-	10000	-
20.108(Stability & Mechanical Hazards)	-	10000	-
20.109(Stability & Mechanical Hazards)	-	10000	-
20.110(Stability & Mechanical Hazards)	-	10000	-
20.111(Stability & Mechanical Hazards)	-	10000	-
20.112(Stability & Mechanical Hazards)	-	10000	-
20.113(Stability & Mechanical Hazards)	-	10000	-
20.114(Stability & Mechanical Hazards)	-	10000	-
20.115(Stability & Mechanical Hazards)	-	10000	-
20.116(Stability & Mechanical Hazards)	-	10000	-
21.1(Mechanical Strength, IS 302-1)	-	10000	-
21.2(Mechanical Strength, IS 302-1)	-	10000	-
22(Construction, IS 302-1)	-	10000	-
22.101(Construction)	-	10000	-
22.102(Construction)	-	10000	-
23.1(Internal Wiring, IS 302-1)	-	10000	-
23.2(Internal Wiring, IS 302-1)	-	10000	-
23.3(Internal Wiring, IS 302-1)	-	10000	-
23.4(Internal Wiring, IS 302-1)	-	10000	-
23.5(Internal Wiring, IS 302-1)	-	10000	-
23.6(Internal Wiring, IS 302-1)	-	10000	-
23.7(Internal Wiring, IS 302-1)	-	10000	-
23.8(Internal Wiring, IS 302-1)	-	10000	-
23.9(Internal Wiring, IS 302-1)	-	10000	-
23.10(Internal Wiring, IS 302-1)	-	10000	-
24.1(Components, IS 302-1)	-	10000	-
24.2(Components, IS 302-1)	-	10000	-
24.5(Components, IS 302-1)	-	10000	-
24.6(Components, IS 302-1)	-	10000	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
26(Terminals for External Conductors, IS 302-1)	-	10000	-
27(Provision for Earthing, IS 302-1)	-	10000	-
27.2(Provision for Earthing, IS 302-1)	-	10000	-
27.3(Provision for Earthing, IS 302-1)	-	10000	-
27.4(Provision for Earthing, IS 302-1)	-	10000	-
27.5(Provision for Earthing, IS 302-1)	-	10000	-
28(Screws & Connections, IS 302-1)	-	10000	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	10000	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	10000	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	10000	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	10000	-
31(Resistance of Rusting, IS 302-1)	-	10000	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	10000	-
19.11.4.1(Electrostatic discharges)	-	10000	-
19.11.4.2(Radiated fields)	-	10000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	10000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
19.11.4.7(Harmonics)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	10000	-
4(GENERAL REQUIREMENTS)	-	10000	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	10000	-
27(Provision for Earthing)	-	10000	-
29(Clearances, Creepage distances and Solid Insulation)	-	10000	-
6(Classification- IS 302-1 )	-	10000	-
6(Classification- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.1(Marking- IS 302-1)	-	10000	-
7.3(Marking- IS 302-1)	-	10000	-
7.4(Marking- IS 302-1)	-	10000	-
7.6(Marking- IS 302-1)	-	10000	-
7.7(Marking- IS 302-1)	-	10000	-
7.8(Marking- IS 302-1)	-	10000	-
7.11(Marking- IS 302-1)	-	10000	-
7.12(Marking- IS 302-1)	-	10000	-
7.13(Marking- IS 302-1)	-	10000	-
7.14(Marking- IS 302-1)	-	10000	-
7.15(Marking- IS 302-1)	-	10000	-
7.101(Marking)	-	10000	-
8( Protection Against Electric Shock, IS 302-1)	-	10000	-
10(Power Input and Current, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
11(Heating, IS 302-1)	-	10000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	10000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	10000	-
14(Transient Over Voltages, IS 302-1)	-	10000	-
15.1(Moisture Resistance, IS 302-1)	-	10000	-
15.2(Moisture Resistance, IS 302-1)	-	10000	-
15(Moisture Resistance, IS 302-1)	-	10000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	10000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	10000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	10000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	10000	-
19.7(Abnormal Operation, IS 302-1)	-	10000	-
19.8(Abnormal Operation, IS 302-1)	-	10000	-
19.9(Abnormal Operation, IS 302-1)	-	10000	-
19.1(Abnormal Operation, IS 302-1)	-	10000	-
19.101(Abnormal Operation)	-	10000	-
19.102(Abnormal Operation)	-	10000	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	10000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	10000	-
20.101(Stability & Mechanical Hazards)	-	10000	-
20.102(Stability & Mechanical Hazards)	-	10000	-
20.103(Stability & Mechanical Hazards)	-	10000	-
20.104(Stability & Mechanical Hazards)	-	10000	-
20.105(Stability & Mechanical Hazards)	-	10000	-
20.106(Stability & Mechanical Hazards)	-	10000	-
20.107(Stability & Mechanical Hazards)	-	10000	-
20.108(Stability & Mechanical Hazards)	-	10000	-
20.109(Stability & Mechanical Hazards)	-	10000	-
20.110(Stability & Mechanical Hazards)	-	10000	-
20.111(Stability & Mechanical Hazards)	-	10000	-
20.112(Stability & Mechanical Hazards)	-	10000	-
20.113(Stability & Mechanical Hazards)	-	10000	-
20.114(Stability & Mechanical Hazards)	-	10000	-
20.115(Stability & Mechanical Hazards)	-	10000	-
20.116(Stability & Mechanical Hazards)	-	10000	-
21.1(Mechanical Strength, IS 302-1)	-	10000	-
21.2(Mechanical Strength, IS 302-1)	-	10000	-
22(Construction, IS 302-1)	-	10000	-
22.101(Construction)	-	10000	-
22.102(Construction)	-	10000	-
23.1(Internal Wiring, IS 302-1)	-	10000	-
23.2(Internal Wiring, IS 302-1)	-	10000	-
23.3(Internal Wiring, IS 302-1)	-	10000	-
23.4(Internal Wiring, IS 302-1)	-	10000	-
23.5(Internal Wiring, IS 302-1)	-	10000	-
23.6(Internal Wiring, IS 302-1)	-	10000	-
23.7(Internal Wiring, IS 302-1)	-	10000	-
23.8(Internal Wiring, IS 302-1)	-	10000	-
23.9(Internal Wiring, IS 302-1)	-	10000	-
23.10(Internal Wiring, IS 302-1)	-	10000	-
24.1(Components, IS 302-1)	-	10000	-
24.2(Components, IS 302-1)	-	10000	-
24.5(Components, IS 302-1)	-	10000	-
24.6(Components, IS 302-1)	-	10000	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	10000	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
26(Terminals for External Conductors, IS 302-1)	-	-	-
27(Provision for Earthing, IS 302-1)	-	-	-
27.2(Provision for Earthing, IS 302-1)	-	-	-
27.3(Provision for Earthing, IS 302-1)	-	-	-
27.4(Provision for Earthing, IS 302-1)	-	-	-
27.5(Provision for Earthing, IS 302-1)	-	-	-
28(Screws & Connections, IS 302-1)	-	-	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	-	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	-	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	-	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	-	-
31(Resistance of Rusting, IS 302-1)	-	-	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	-	-
19.11.4.1(Electrostatic discharges)	-	-	-
19.11.4.2(Radiated fields)	-	-	-
19.11.4.3(Fast transient bursts)	-	-	-
19.11.4.4(Surge immunity test)	-	-	-
19.11.4.5(Immunity to conducted discharges)	-	-	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	-	-
19.11.4.7(Harmonics)	-	-	-
19.11.4.5(Immunity to conducted discharges)	-	-	-
4(GENERAL REQUIREMENTS)	-	-	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	-	-
27(Provision for Earthing)	-	-	-
29(Clearances, Creepage distances and Solid Insulation)	-	-	-

13 May, 2028

-
Included w.e.f. 14.08.2025 Exclusion: "19.11.4.1 (Electrostatic discharges) 19.11.4.2 (Radiated fields) 19.11.4.3 (Fast transient bursts) 19.11.4.4 (Surge immunity test) 19.11.4.5 (Immunity to conducted discharges) 19.11.4.6 (Class 3 Voltage dips and interruptions) 19.11.4.7 (Harmonics)

IS 26 (2024)

Tin ingot - Specification (fifth revision)

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Suppy of material)	-	10000	-
Cl-6(Raw Materials and manufacture)	-	10000	-
Cl-7.1, 7.2 Table-1(Sn, Min)	-	10000	-
Cl-7.1, 7.2 Table-1(Sb, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(As, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Bi, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Cd, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Cu, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Fe, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Pb, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Al, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Zn, Max)	-	10000	-
Cl-7.1, 7.2 Table-1(Total of All Impurities, Max)	-	10000	-
Cl-7.2(Chemical analysis)	-	10000	-
Cl-8(Surface condition of ingots)	-	10000	-
Cl-9(Shape and mass of the ingots)	-	10000	-
Cl-14(Marking)	-	10000	-

13 May, 2028

-
Included w.e.f 31.07.2025

IS 444 (2025)

Rubber Hoses, Textile-Reinforced, for General-Purpose Water Applications - Specification (Sixth Revision)

ALL

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Material and Construction)	-	25000	-
Cl-6.1(Internal diameters and tolerances)	-	25000	-
Cl-6.2(Concentricity)	-	25000	-
Cl-6.3(Tolerance of length)	-	25000	-
Cl-6.4(Minimum thickness of lining and cover)	-	25000	-
Cl-7.1, Table-2 (i)(Minimum tensile strength)	-	25000	-
Cl-7.1, Table-2 (ii)(Minimum elongation at break)	-	25000	-
Cl-7.1, Table-2 (iii)("Resistance to ageing: Change in tensile strength from original value (max) . Change in elongation at break from original value (max)")	-	25000	-
Cl-7.2, Table-3 (i)(Proof pressure at 23 0 C)	-	25000	-
Cl-7.2, Table-3 (ii)(Change in length at proof pressure)	-	25000	-
Cl-7.2, Table-3 (iii)(Minimum burst pressure)	-	25000	-
Cl-7.2, Table-3 (iv)(Adhesion between component)	-	25000	-
Cl-7.2, Table-3 (v)(Ozone resistance)	-	25000	-
Cl-7.2, Table-3 (vi)(Flexibility at 23ºC)	-	25000	-
Cl-7.2, Table-3 (vii)(Low-temperature flexibility)	-	25000	-
Cl-8(Marking)	-	25000	-

13 May, 2028

-
Included w.e.f 31.07.2025

IS 191 (2007)

Copper - Specification (Fourth Revision)

ALL

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-Table 1(GRADES/DESIGNATIONS)	-	5000	-
5.1- Table 2(L)	-	5000	-
5.1- Table 2(L1)	-	5000	-
5.1- Table 2(h)	-	5000	-
5.1- Table 2(h1)	-	5000	-
5.1- Table 2(b)	-	5000	-
5.1- Table 2(b1)	-	5000	-
5.1- Table 2(R)	-	5000	-
5.1- Table 2(R1)	-	5000	-
5.1- Table 2(R2 )	-	5000	-
5.1- Table 2(α )	-	5000	-
5.1- Table 2( β )	-	5000	-
5.1- Table 2(γ)	-	5000	-
5.2(Billets)	-	5000	-
5.4-Table 3 (For Billets)(Mass)	-	5000	-
5.2-Table 3 (For Billets)(Diameter)	-	5000	-
5.2-Table 3 (For Billets)(Length)	-	5000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	5000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Ingots)(Mass)	-	5000	-
5.4-Table 3 (Cast cakes)(Mass)	-	5000	-
5.3-Table 3 (Cast cakes)(Width)	-	5000	-
5.3-Table 3 (Cast cakes)(thickness )	-	5000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	5000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	5000	-
8.2(FREEDOM FROM DEFECTS)	-	5000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
4-Table 1(GRADES/DESIGNATIONS)	-	5000	-
5.1- Table 2(L)	-	5000	-
5.1- Table 2(L1)	-	5000	-
5.1- Table 2(h)	-	5000	-
5.1- Table 2(h1)	-	5000	-
5.1- Table 2(b)	-	5000	-
5.1- Table 2(b1)	-	5000	-
5.1- Table 2(R)	-	5000	-
5.1- Table 2(R1)	-	5000	-
5.1- Table 2(R2 )	-	5000	-
5.1- Table 2(α )	-	5000	-
5.1- Table 2( β )	-	5000	-
5.1- Table 2(γ)	-	5000	-
5.2(Billets)	-	5000	-
5.4-Table 3 (For Billets)(Mass)	-	5000	-
5.2-Table 3 (For Billets)(Diameter)	-	5000	-
5.2-Table 3 (For Billets)(Length)	-	5000	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	5000	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	5000	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	5000	-
5.4-Table 3 (Ingots)(Mass)	-	5000	-
5.4-Table 3 (Cast cakes)(Mass)	-	5000	-
5.3-Table 3 (Cast cakes)(Width)	-	5000	-
5.3-Table 3 (Cast cakes)(thickness )	-	5000	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	5000	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	5000	-
7.1 - Table 4(Silver- IS 440)	-	5000	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	5000	-
7.1 - Table 4(Phosphorus- IS 440)	-	5000	-
7.1 - Table 4(Arsenic- IS440)	-	5000	-
7.1 - Table 4(Antimony-IS440)	-	5000	-
7.1 - Table 4(Bismuth-IS 440)	-	5000	-
7.1 - Table 4(Iron IS 440)	-	5000	-
7.1 - Table 4(Lead IS 440)	-	5000	-
7.1 - Table 4(Nickel IS 440)	-	5000	-
7.1 - Table 4(Oxygen IS 440)	-	5000	-
7.1 - Table 4(Selenium - IS 440)	-	5000	-
7.1 - Table 4(Sulphur- IS 440)	-	5000	-
7.1 - Table 4(Tellurium- IS 440)	-	5000	-
7.1 - Table 4(Tin - IS 440)	-	5000	-
7.1 - Table 4(Znic-IS 440)	-	5000	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	5000	-
7.1 - Table 4(Total Impurities- IS 440)	-	5000	-
8.1(FREEDOM FROM DEFECTS)	-	5000	-
8.2(FREEDOM FROM DEFECTS)	-	5000	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	5000	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	5000	-
13(Marking)	-	5000	-
13(Marking)	-	5000	-
13(Marking)	-	5000	-

13 May, 2028

-
Included w.e.f 01.08.2025

IS 13273 (1991)

Vitreous enamelled inner tanks for storage water heater - specification

All

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.3.2.1(1238)	-	30000	-
Cl. 5.3.2.1(1238)	-	30000	-
Cl. 5.3.2.3(13273)	-	30000	-
Cl 5.3.2.2(13273)	-	30000	-
Cl. 5.3.3(13273)	-	30000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	30000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	30000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	30000	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	30000	-
Cl. 5.3.2.5(13273)	-	30000	-
Cl. 5.4(13273)	-	30000	-
Cl. 5.5(13273)	-	30000	-

13 May, 2028

-
-

IS 17790 (2022)

INSULATED FLASK FOR DOMESTIC USE SPECIFICATION

All

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Manufacture and Workmanship)	-	28000	-
5.3(Welding Defects)	-	28000	-
7.1(Material)	-	28000	-
7.1.2.1 & 7.1.2.2(Thickness)	-	28000	-
7.1.3(Coating Thickness)	-	28000	-
7.1.3(Material – coating cadmium)	-	28000	-
7.1.2.2(Bisphenol A (BPA))	-	28000	-
7.1.4.3(O-Ring / Washer- Defects)	-	28000	-
7.2(Capacity)	-	28000	-
7.3(Heat Retention Capability)	-	28000	-
7.4(Cold Retention Capability)	-	28000	-
7.5.1(Drop Impact Test)	-	28000	-
7.5.2(Pendulum Impact Test)	-	28000	-
7.6(Fixing Strength of the Handle)	-	28000	-
7.7(Test for Strength of Shoulder Strap)	-	28000	-
7.8(Test for strength of cord)	-	28000	-
7.9(Leakage Test)	-	28000	-
7.10(Joint Leak Test)	-	28000	-
7.11(Staining Test)	-	28000	-
7.13(Seepage test)	-	28000	-
7.14(Test for Lever, device for operating Or regulating flow test)	-	28000	-
7.15(Test for length of the shoulder cap)	-	28000	-
7.16(Stability of Flask)	-	28000	-
7.17(Pour Test)	-	28000	-
9.1(Marking)	-	28000	-
9.2(BIS certification marking)	-	28000	-
10(Packaging)	-	28000	-
7.1.3(Coating- Adhesion test)	-	28000	-
7.1.3(Coating - Thickness test)	-	28000	-
7.1.3(Coating- Salt water corrosion test)	-	28000	-
7.1.4.1(Stopper)	-	28000	-
7.1.4.2(O-ring/washer- Overall migration)	-	28000	-
7.1.4.2(O-ring/washer- Shore hardness)	-	28000	-
7.1.4.2(O-ring/washer- BPA)	-	28000	-
7.1.5(Auxillary closure)	-	28000	-
7.12(Check for PUF (Polyurethane Foam) or Any Other Similar Thermal Insulation Material)	-	28000	-
7.18(Endurance Test for O-Ring, Washer and Stopper)	-	28000	-

13 May, 2028

-
Included w.e.f.15.07.2025

IS 16440 (2016)

Stainless steel milk cans - Specification

ALL

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Carbon)	-	30000	-
5.2(Sulphur)	-	30000	-
5.2(phosphorus)	-	30000	-
5.2(Manganese)	-	30000	-
5.2(Silicon)	-	30000	-
5.2(Chromium)	-	30000	-
5.2(Nickel)	-	30000	-
5.2(molybdenum)	-	30000	-
3.0(Capacity test)	-	30000	-
6.3(Hardness test)	-	30000	-
6.1(Pressure check for leakage and bulging)	-	30000	-
6.2(Drop test)	-	30000	-
6.4(Dye penetration test)	-	30000	-
"As per Clause 4 & Table 1"(Shape & Dimensions)	-	30000	-
As per Clause 5.4(Thickness of parts)	-	30000	-
As per Clause 5.5(Mass of can (Weight))	-	30000	-
As per Clause 5.6(Construction)	-	30000	-
Clause 5.6.1(Body)	-	30000	-
As per Clause 5.6.2(Handle)	-	30000	-
Clause 5.6.3(Bottom ring)	-	30000	-
Clause 5.6.4(Lid)	-	30000	-
Clause 5.6.6(Finish)	-	30000	-
Clause 5.6.7(Heat treatment and Passivation)	-	30000	-
Clause 6.5(Leakage test)	-	30000	-
Clause 4 & Table 1"(Shape & Dimensions)	-	30000	-
Clause 5.4(Thickness of parts)	-	30000	-
Clause 5.5(Mass of can (Weight))	-	30000	-
Clause 5.6(Construction)	-	30000	-
Clause 5.6.1(Body)	-	30000	-
Clause 5.6.2(Handle)	-	30000	-
Clause 5.6.3(Bottom ring)	-	30000	-
Clause 5.6.6(Finish)	-	30000	-
Clause 5.6.7(Heat treatment and Passivation)	-	30000	-
Clause 6.5(Leakage test)	-	30000	-

13 May, 2028

-
Included w.e.f 31.07.2025

IS/ISO 9994 (2018)

Lighters Safety specifications First Revision

ALL

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Flame Generation)	-	21000	-
Cl.4.2(Flame Height)	-	21000	-
Cl.4.3(Flame-Height adjustment)	-	21000	-
Cl.4.4(Resistance to spitting or sputtering and flaring)	-	21000	-
Cl.4.5(Flame Extinction)	-	21000	-
Cl.4.6(Volumetric displacement of Fuel)	-	21000	-
Cl.4.7(Mass of Fuel)	-	21000	-
Cl.5.1(External Finish)	-	21000	-
Cl.5.2(Compatibility of Fuel)	-	21000	-
Cl.5.3(Resistance to Fuel Loss)	-	21000	-
Cl.5.4(Resistance to dropping)	-	21000	-
Cl.5.5(Resistance to elevated Temperature)	-	21000	-
Cl.5.6(Resistance to internal Pressure)	-	21000	-
Cl.5.7(Burning Behavior)	-	21000	-
Cl.5.8(Resistance to cyclic burning)	-	21000	-
Cl.5.9(Resistance to Continue Burning)	-	21000	-
6.6, 6.6.3.1(Refilling test-IS/ISO 9994)	-	21000	-
6.6, 6.6.3.2(Refilling test-IS/ISO 9994)	-	21000	-

13 May, 2028

-
Included w.e.f 07.07.2025

IS/ISO 22702 (2018)

Utility lighters Safety specifications First Revision

ALL

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Flame generation)	-	21000	-
4.2(Flame heights)	-	21000	-
4.3(Flame- height adjustment)	-	21000	-
4.4("Resistance to Spitting or Sputtering and flaring")	-	21000	-
4.5(Flame extinction)	-	21000	-
4.6(Volumetric Displacement)	-	21000	-
5.2(Resistance to dropping)	-	21000	-
5.3(Resistance to elevated temperature)	-	21000	-
5.4(Burning behavior)	-	21000	-
5.5(Resistance to continuous burn)	-	21000	-
5.6(Resistance to cyclic burn)	-	21000	-
5.7(External Finish)	-	21000	-
5.8(Compatibility with fuel)	-	21000	-
5.9(Resistance to internal pressure)	-	21000	-
6(Refilling Test)	-	21000	-

13 May, 2028

-
Included w.e.f 07.07.2025

IS 13273 (2024)

Vitreous Enamelled Inner Tanks for Storage Water Heater - Specification (First Revision)

All

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Base Metal Thickness-Micrometer at 3 points)	-	30000	-
5.1.2(Fittings Material - Visual + IS 2082 Reference)	-	30000	-
5.2(Welding - Visual inspection of weld quality)	-	30000	-
5.3.2.1(Toxic Material Release - IS 12038 (Part 1): ICP-OES or AAS)	-	30000	-
5.3.2.2(Resistance to Citric Acid - Annex B test using 10% citric acid)	-	30000	-
5.3.2.3(Solubility Test - Annex C: Boiling in sodium bicarbonate)	-	30000	-
5.3.2.4(Thermal Shock - Heat to 140°C, quench in water)	-	30000	-
5.3.2.5(Impact Resistance - Drop steel ball from 80 cm)	-	30000	-
5.3.3(Magnetic coating thickness gauge - Enamel Thickness)	-	30000	-
5.3.4(Coating Continuity - Visual + segment check (5.6))	-	30000	-
5.3.4.1(Cathodic Protection - Check anode type & weight)	-	30000	-
5.3.5(Edges & Fittings Coating - Visual inspection)	-	30000	-
5.4(Storage Capacity - Fill and measure displaced water)	-	30000	-
5.5(Hydrostatic Test - Apply pressure as per IS 302-2-21)	-	30000	-
5.6(Enamel Coverage - Cut tank & inspect segments)	-	30000	-
6.2.1(Marking & Traceability - Check labeling & BIS mark)	-	30000	-
7.2(Sampling - IS 2500/ISO 2859-1)	-	30000	-

13 May, 2028

-
Included w.e.f 07.07.2025

IS 7466 (2023)

Rubber Gasket for Pressure Cooker ï¿½ Specification ( Second Revision )

ALL

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 3(Types)	-	19500	-
Cl. No. 4.1(Material)	-	19500	-
Cl. No. 4.2(Workmanship and Finish)	-	19500	-
Cl. No. 4.3(Dimensions)	-	19500	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	19500	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	19500	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	19500	-
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	19500	-
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	19500	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	19500	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	19500	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	19500	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	19500	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	19500	-
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	19500	-
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	19500	-
Cl. No. 4.4, table no. 1(xiii)(N-Nitrosatables)	-	19500	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	19500	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	19500	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	19500	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	19500	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	19500	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	19500	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	19500	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	19500	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	19500	-
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	19500	-
Cl. No.4.6(Performance test)	-	19500	-
Cl. No. 4.7(Quality of Reagent)	-	19500	-
Cl. No. 5(Packing and Marking)	-	19500	-
Cl. No. 3(TYPES)	-	19500	-
Cl. No. 4.1(Material)	-	19500	-
Cl. No. 4.2(Workmanship and Finish)	-	19500	-
Cl. No. 4.3(Dimensions)	-	19500	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	19500	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	19500	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	19500	-
Cl. No. 4.4, table no. 1(iv)(Hardness, Tensile strength, Elongation at break percent)	-	19500	-
Cl. No. 4.4, table no. 1(v)(Hardness, Tensile strength, Elongation at break percent)	-	19500	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	19500	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	19500	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	19500	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	19500	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	19500	-
Cl. No. 4.4, table no. 1(xi)(Total zinc oxide, percent by mass, )	-	19500	-
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	19500	-
Cl. No. 4.4, table no. 1(xiii)(N-Nitrosatables)	-	19500	-
Cl. No. 4.4, table no. 1(xiv)(Extractables)	-	19500	-
Cl. No. 4.4, table no. 1(xv)(Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP))	-	19500	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	19500	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	19500	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	19500	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	19500	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	19500	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	19500	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	19500	-
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	19500	-
Cl. No.4.6(performance test )	-	19500	-
Cl. No. 4.7(Quality of Reagent)	-	19500	-
Cl. No. 5(PACKING AND MARKING)	-	19500	-
Cl. No. 3(TYPES)	-	19500	-
Cl. No. 4.1(Material)	-	19500	-
Cl. No. 4.2(Workmanship and Finish)	-	19500	-
Cl. No. 4.3(Dimensions)	-	19500	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	19500	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	19500	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	19500	-
Cl. No. 4.4, table no. 1(iv)(Hardness, Tensile strength, Elongation at break percent)	-	19500	-
Cl. No. 4.4, table no. 1(v)(Hardness, Tensile strength, Elongation at break percent)	-	19500	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	19500	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	19500	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	19500	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	19500	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	19500	-
Cl. No. 4.4, table no. 1(xi)(Total zinc oxide, percent by mass, )	-	19500	-
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	19500	-
Cl. No. 4.4, table no. 1(xiii)(N-Nitrosatables)	-	19500	-
Cl. No. 4.4, table no. 1(xiv)(Extractables)	-	19500	-
Cl. No. 4.4, table no. 1(xv)(Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP))	-	19500	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	19500	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	19500	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	19500	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	19500	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	19500	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	19500	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	19500	-
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	19500	-
Cl. No.4.6(performance test )	-	19500	-
Cl. No. 4.7(Quality of Reagent)	-	19500	-
Cl. No. 5(PACKING AND MARKING)	-	19500	-

13 May, 2028

-
Included w.e.f 07.07.2025

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

ALL

170000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking)	-	170000	-
4(Type)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Carbon Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Silicon Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Manganese Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nickel Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Chromium Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Sulphur Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Phouphorous Content)	-	170000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nitrogen Content)	-	170000	-
6(Thickness of sheet/strip)	-	170000	-
6(Depth of bowl)	-	170000	-
6(Internal dimensions of the bowl)	-	170000	-
6(Bowl locating limits)	-	170000	-
6(Co-ordinating sizes)	-	170000	-
7.1(Consruction and workmanship)	-	170000	-
7.1.1(Consruction and workmanship)	-	170000	-
7.2(Consruction and workmanship)	-	170000	-
7.2.1(Consruction and workmanship)	-	170000	-
7.3(Drainers)	-	170000	-
7.4(Waste outlet)	-	170000	-
7.5(Tap holes)	-	170000	-
7.6(Overflows)	-	170000	-
8(Finish)	-	170000	-
5(MATERIALS)	-	170000	-
6.1.1(Thickness of Sheet/Strip)	-	170000	-
6.1.2(Thickness of Sheet/Strip)	-	170000	-
6.2(Depth of Bowls)	-	170000	-
6.3(Internal Dimensions of Bowls)	-	170000	-
6.4.1(Bowl Locating Limits)	-	170000	-
6.5(Coordinating Sizes)	-	170000	-
7.1(CONSTRUCTION AND WORKMANSHIP)	-	170000	-
7.1.1(CONSTRUCTION AND WORKMANSHIP)	-	170000	-
7.2.1(CONSTRUCTION AND WORKMANSHIP)	-	170000	-
7.3(CONSTRUCTION AND WORKMANSHIP)	-	170000	-
7.4(Waste Outlet)	-	170000	-
7.5(Tap Holes)	-	170000	-
7.6(OVERFLOW)	-	170000	-
Clause no. 4(types)	-	170000	-
Caluse no. 5("Material -Austenitic stainless steel of Grade Designation")	-	170000	-
Clause no. 6.1(Thickness of sheet)	-	170000	-
Clause no. 6.2(Depth of Bowls)	-	170000	-
Clause no. 6.3(Internal dimensions of bowls)	-	170000	-
Clause no. 6.4(Bowl Locating Limits)	-	170000	-
Clause no. 6.5, Table No. 1(Dimension of the sink)	-	170000	-
Clause no. 7(Construction and workmanship)	-	170000	-
Clause no. 8(Finish)	-	170000	-
Clause no. 9(Mark)	-	170000	-

13 May, 2028

-
Included w.e.f.30.06.2025

IS 18800 (2023)

Stainless steel feeding bottle for infants -- Specification

All

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1(Carbon - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Silicon - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Nickel - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Sulphur - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Phosphorous - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Nitrogen - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Molybdenum - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Other Elements - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
5.1.1(Description)	-	30000	-
5.1.2(Manufacture, Workmanship, Finish and Appearance)	-	30000	-
5.1.3(Wall Thickness)	-	30000	-
5.1.4(Capacity)	-	30000	-
5.2(Mechanical Requirements)	-	30000	-
5.3.1(Leakage Test)	-	30000	-
5.3.2(Drop Test)	-	30000	-
5.3.3(Compressive Deformation Resistance)	-	30000	-
5.3.4(Permanency of Pigments of Printed Container)	-	30000	-
5.1.1(Description)	-	30000	-
5.1.2(Manufacture, Workmanship, Finish and Appearance)	-	30000	-
5.1.3(Wall Thickness)	-	30000	-
5.1.4(Capacity)	-	30000	-
5.2(Mechanical Requirements)	-	30000	-
5.3.1(Leakage Test)	-	30000	-
5.3.2(Drop Test)	-	30000	-
5.3.3(Compressive Deformation Resistance)	-	30000	-
5.3.4(Permanency of Pigments of Printed Container)	-	30000	-
Cl.5.3.4(Permanency of Pigments - Annex D of IS 18800)	-	30000	-
Cl.4.1(Carbon - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Silicon - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Nickel - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Sulphur - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Phosphorous - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Nitrogen - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Molybdenum - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
Cl.4.1(Other Elements - IS 228 and its parts or any other intrumental/chemical methods)	-	30000	-
5.1.1(Description)	-	30000	-
5.1.2(Manufacture, Workmanship, Finish and Appearance)	-	30000	-
5.1.3(Wall Thickness)	-	30000	-
5.1.4(Capacity)	-	30000	-
5.2(Mechanical Requirements)	-	30000	-
5.3.1(Leakage Test)	-	30000	-
5.3.2(Drop Test)	-	30000	-
5.3.3(Compressive Deformation Resistance)	-	30000	-
5.3.4(Permanency of Pigments of Printed Container)	-	30000	-
5.1.1(Description)	-	30000	-
5.1.2(Manufacture, Workmanship, Finish and Appearance)	-	30000	-
5.1.3(Wall Thickness)	-	30000	-
5.1.4(Capacity)	-	30000	-
5.2(Mechanical Requirements)	-	30000	-
5.3.1(Leakage Test)	-	30000	-
5.3.2(Drop Test)	-	30000	-
5.3.3(Compressive Deformation Resistance)	-	30000	-
5.3.4(Permanency of Pigments of Printed Container)	-	30000	-
Cl.5.3.4(Permanency of Pigments - Annex D of IS 18800)	-	30000	-

13 May, 2028

-
Included w.e.f 03.07.2025

IS 16218 (2014)

Forks - Specification

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(food grade stainless steel.)	-	15000	-
3.2 (i)(Brass as parent material)	-	15000	-
3.2(ii)(Brass plated with pure silver)	-	15000	-
3.3(Plastic handle)	-	15000	-
4(Shapes and Dimensions)	-	15000	-
5(Manufacture)	-	15000	-
6.1(Workmanship)	-	15000	-
6.2(Finish)	-	15000	-
9(Marking)	-	15000	-
10(Packing)	-	15000	-

13 May, 2028

-
Included w.e.f 03.07.2025

IS 16286 (2014)

Spoons - Specification

all

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(food grade stainless steel.)	-	15000	-
3.2 (i)(Brass as parent material)	-	15000	-
3.2(ii)(Brass plated with pure silver)	-	15000	-
3.3(Plastic handle)	-	15000	-
4(Shapes and Dimensions)	-	15000	-
5.1(Manufacture)	-	15000	-
5.2(Workmanship)	-	15000	-
5.3(Finish)	-	15000	-
8(Marking)	-	15000	-
9(Packing)	-	15000	-
Cl-6.1(Staining Test)	-	15000	-
Cl-6.2(Bending Test)	-	15000	-
Cl-6.3(Load Test)	-	15000	-
Cl-6.4.1(Boiling)	-	15000	-
Cl-6.4.2(Impact)	-	15000	-
Cl-6.4.3(Staining)	-	15000	-

13 May, 2028

-
Included w.e.f 03.07.2025

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

all

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Types)	-	15000	-
Clause.4.0(Carbon)	-	15000	-
Clause.4.0(Sulphur)	-	15000	-
Clause.4.0(Sulphur)	-	15000	-
Clause.4.0(Phosphorus)	-	15000	-
Clause.4.0(Silicon)	-	15000	-
Clause.4.0(Manganese)	-	15000	-
Clause.5.0(Supply of Material)	-	15000	-
Clause.5.0(Supply of Material)	-	15000	-
Clause.6.0(Workmanship)	-	15000	-
Clause.7.0(Straightness)	-	15000	-
Clause.8.0(Basis of Calculation)	-	15000	-
Clause.9.0(Length)	-	15000	-
Clause.10.0(Dimensions and properties)	-	15000	-
Clause.10.0(Dimensions and properties)	-	15000	-
Clause.11.0(General)	-	15000	-
Clause.11.0(Outside Dimension)	-	15000	-
Clause.11.0(Thickness)	-	15000	-
Clause.11.0(Thickness)	-	15000	-
Clause.11.0(Concavity and Convexity)	-	15000	-
Clause.11.0(Squareness of Sides)	-	15000	-
Clause.11.0(External Corner Radiius)	-	15000	-
Clause.11.0(Straightness and twist)	-	15000	-
Clause.12.0(Dimension Tolerances)	-	15000	-
Clause.12.0(Dimension Tolerances)	-	15000	-
Clause.13.0(Surface Protection)	-	15000	-
Clause.14.0(Testing)	-	15000	-
Clause.15.0(Tensile test)	-	15000	-
Clause.15.0(Yield strength)	-	15000	-
Clause.15.0(Elognation Percent)	-	15000	-
Clause.18.0(Marking)	-	15000	-
6(Workmanship)	-	15000	-
10(Dimensions and Properties)	-	15000	-
11(Measurement of Shape and Size)	-	15000	-
12(Dimensions and Tolerances)	-	15000	-
13(Surface Protection)	-	15000	-
15(Tensile Test)	-	15000	-

13 May, 2028

-
Included w.e.f 03.07.2025

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

all

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	11000	-
5(Lining - IS 444)	-	11000	-
5(Reinforcement - IS 444)	-	11000	-
5(Cover - IS 444)	-	11000	-
5(Lining and Cover - IS 444)	-	11000	-
6.1- Table 1(Internal diameters - ISO 4671)	-	11000	-
6.2(Concentricity - ISO 4671)	-	11000	-
6.3(Length -IS 4671)	-	11000	-
6.4( thickness of the lining plus cover - ISO 4671)	-	11000	-
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	11000	-
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	11000	-
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	11000	-
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	11000	-
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	11000	-
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	11000	-
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	11000	-
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	11000	-
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	11000	-
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	11000	-
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	11000	-
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	11000	-
7.2 - Table 3(Adhesion between components - ISO 8033)	-	11000	-
7.2 - Table 3(Ozone resistance - ISO 7326)	-	11000	-
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	11000	-
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	11000	-

13 May, 2028

-
Included w.e.f 26.06.2025

IS 10908 (2023)

FLEXIBLE RUBBER TUBING FOR LIQUEFIED PETROLEUM GAS SPECIFICATION Second Revision

all

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The materials used in the manufacture of tubing shall be homogeneous and shall be resistant to outdoor exposure.)	-	15000	-
4.1(The tubing made out of this material shall be green in colour and shall be supplied normally in cut lengths or in rolls of running length)	-	15000	-
4.1("when supplied in cut lengths, the pieces shall be of minimum 1.0 m to maximum of 1.5 m in length. ")	-	15000	-
4.2(The walls shall be seamless and free from all visible defects, such as lumps, blow-holes, cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas.)	-	15000	-
4.3.1(The tubing when supplied in 6.4 mm inside diameter; the tolerance as per table-1)	-	15000	-
4.3.1(The tubing when supplied in 7.00 mm inside diameter; the tolerance as per table-1)	-	15000	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.20 mm))	-	15000	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.50 mm))	-	15000	-
4.4.1(When tested in accordance with the method given in Annex B, the tubing shall fit over the standard and oversize metal nozzle shown in Fig. 1, 2 and 3.)	-	15000	-
4.4.2("When tested in accordance with the method given in Annex B, the tubing shall remain attached to both nozzles throughout the test period. ")	-	15000	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), the increase in the outside diameter or the tubing shall not be more than 15 percent.)	-	15000	-
4.12("When tested in accordance with the method described in Annex F, the tubing shall not burn to either of the outer marks within the test period of 45 s")	-	15000	-
4.11("When tested in accordance with the method described in Annex E, the slit tube shall not show any breakage on surface or cracks or defects.")	-	15000	-
4.10(When tested in accordance with Annex D, the npentane absorbed shall not exceed 15 percent of the initial mass of the tubing and the amount of npentane extractable matter shall not exceed 10 percent of the initial mass of tubing.)	-	15000	-
4.9(60 cm long tubing shall be subjected to a crushing force of 350 N applied on the middle of the tubing evenly over a length of 25 mm for 5 minutes, and 30 min after removal of the force it shall not show any deformation or collapse, nor shall it leak when subjected to an internal air pressure of 250 kPa)	-	15000	-
4.8.2(The tubing shall be so flexible that it will make contact with a cylindrical former of radius 68 mm for at least 110° of its circumference when the immersed tubing is placed over the former and a mass of 1.6 kg is attached to each end.)	-	15000	-
4.8.1("The tubing shall be immersed for 72 h in liquid pentane and then conditioned at room temperature for 24 h, after which it shall be tested in accordance with the method prescribed in Annex C, the gas pressure shown on the manometer shall not drop by more than 1 kPa")	-	15000	-
4.7("The flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100 °C for 72 h in accordance with the normal method prescribed in IS 3400 (Part 4). It shall not show a change of + 10° A of its original shore hardness value (see 4.6) after accelerated ageing")	-	15000	-
4.6(The hardness on the flat surface of the cut/slit tubing shall be measured as prescribed in IS 3400 (Part 2/Sec 4), the shore hardness shall be 60 ± 5°A.)	-	15000	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), there shall be no sign of leakage in the tubing. Also the same shall not burst when the pressure is increased to 0.5 MPa or 500 kPa (5 bar), The test shall be carried out on a length of 60 cm.)	-	15000	-

13 May, 2028

-
Included w.e.f 26.06.2025

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

all

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.2 - Table 1(Bore size)	-	9000	-
Cl. 3.2 - Table 1(Lining Thickness)	-	9000	-
Cl. 3.2 - Table 1(Cover Thickness)	-	9000	-
Cl. 3.2 - Table 1(Length %)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Lining MPA)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Cover Mpa)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Lining %)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Cover %)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining %)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover %)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining %)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover %)	-	9000	-
Cl. 3.4 - Table3(Pressure Tests)	-	9000	-
Cl. 3.4 - Table3(Adhesion KN/m Min)	-	9000	-
Cl. 3.2 - Table 1(Bore size, mm)	-	9000	-
Cl. 3.2 - Table 1(Lining Thickness, mm)	-	9000	-
Cl. 3.2 - Table 1(Cover Thickness, mm)	-	9000	-
Cl. 3.2 - Table 1(Length)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Lining, Mpa)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Cover, Mpa)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	9000	-
Cl. 3.4 - Table3(Pressure Tests)	-	9000	-
Cl. 3.4 - Table3(Adhesion, KN/m Min)	-	9000	-
Cl. 3.4 - Table3(Adhesion)	-	9000	-
Cl. 3.4 - Table3(Pressure Tests)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	9000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	9000	-
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Cover)	-	9000	-
Cl. 3.3 - Table 2(Tensile strength - Lining)	-	9000	-
Cl. 3.2 - Table 1(Length)	-	9000	-
Cl. 3.2 - Table 1(Cover Thickness)	-	9000	-
Cl. 3.2 - Table 1(Lining Thickness)	-	9000	-
Cl. 3.2 - Table 1(Bore size)	-	9000	-

13 May, 2028

-
Included w.e.f 26.06.2025

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

all

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	11000	-
Clause 4.2(Material)	-	11000	-
Clause 4.2.1(Lining)	-	11000	-
Clause 4.2.2 (a)(Reinforcement)	-	11000	-
Clause 4.2.2 (b)(Reinforcement)	-	11000	-
Clause 4.2.3(Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	11000	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	11000	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	11000	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	11000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	11000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	11000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	11000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	11000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	11000	-
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	11000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	11000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	11000	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	11000	-
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	11000	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	11000	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	11000	-
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	11000	-
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	11000	-
Clause 5.2.1(BIS Certification Marking )	-	11000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

all

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	11000	-
Clause 4.1 (General)	-	11000	-
Clause 4.1(General)	-	11000	-
Clause 4.2(Material)	-	11000	-
Clause 4.2.1(Lining)	-	11000	-
Clause 4.2.2(Reinforcement)	-	11000	-
Clause 4.2.3(Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	11000	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	11000	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	11000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	11000	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	11000	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	11000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	11000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	11000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	11000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	11000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	11000	-
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	11000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	11000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	11000	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	11000	-
Clause 5.2 (c)(Marking Nominal bore )	-	11000	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	11000	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	11000	-
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	11000	-
Clause 5.2.1(BIS Certification Marking )	-	11000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 5082 (1998)

Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(CHEMICAL COMPOSITION Table 1)	-	15000	-
Clause 5(FREEDOM FROM DEFECTS)	-	15000	-
8.1(MECHANICAL TEST Tensile Strength Min, Mpa)	-	15000	-
8.1(MECHANICAL TEST (0.2 Percent Proof Stress Min, Mpa))	-	15000	-
8.1(Percent Elongation on 5.65 Min)	-	15000	-
8.1(Electrical Conductivity at 20°C,Min)	-	15000	-
8.1(Maximum Electrical Resistivity at 20°C ohm-mm/mm2)	-	15000	-
8.2(Bend Test)	-	15000	-
Clause 10(DIMENSIONAL TOLERANCES)	-	15000	-
6.1, Table 1(Aluminium)	-	15000	-
6.1, Table 1(Copper)	-	15000	-
6.1, Table 1(Magnesium)	-	15000	-
6.1, Table 1(Silicon)	-	15000	-
6.1, Table 1(Manganese)	-	15000	-
6.1, Table 1(Zinc)	-	15000	-
6.1, Table 1(Titanium)	-	15000	-
6.1, Table 1(Chromium)	-	15000	-
6.1, Table 1(Iron)	-	15000	-
6.1, Table 1(Vanadium)	-	15000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 17150 (2019)

Mini domestic water heater for use with piped natural gas (PNG) ? specification

ALL

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
26(Hot water output, Declared Value)	-	30000	-
25(When tested as per annex D, at the nominal gas rate with the appliance adjusted to give a temperature rise of 45±5°C between the water inlet and outlet , the time to achieve 90% of this temperature rise-)	-	30000	-
24(Temperature of synthetic rubber diaphragm in gas carrying components)	-	30000	-
24(Temperature of the surface in normal use)	-	30000	-
24(Surface temperature:Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	30000	-
24(Wall, Floor, Ceiling temperatures: Rise of Temperature above room temperature in , after two hours of operation)	-	30000	-
23(There shall be no extinction of flame on any of the burner operating at the maximum consumption when the appliance is placed in a normal current of air with velocity of 2 m/s as measured with a rotating vane anemometer. The location of the appliance relative to the neighbouring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation, applicable for all pressure 20-25 gf/cm².)	-	30000	-
22(While the appliance is in operation at full gas consumption and the appliance is in thermal equilibrium, the flame shall be immediately reduced to the minimum possible and then brought back to the full size, the operation shall be repeated five times, no flash back shall occur during the test, applicable for pressure 20-25 gf/cm².)	-	30000	-
21(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	30000	-
20(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	30000	-
20(It shall be possible to operate the appliance with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	30000	-
19.3(if the burner is ignited from a pilot flame , ignition shall be smooth at pressure from 20-25 gf/cm² with the tap turned full on and ignition shall be effected without delay after turning on the taps.)	-	30000	-
19.2(if the flame is applied to any one burner pors when the gas is flowing , flame travel shall be complete. This applies for all pressures from 20 to 25 gf/cm² taps being fully open.)	-	30000	-
19.1(Where the burner or burners are lighted by automatic ignition , it shall not be possible for gas to be admitted to the main burner without igniters being on.)	-	30000	-
19.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	30000	-
18( (D = Declared Value, Gas Consumption)	-	30000	-
17(Ratio of Carbon Monoxide to Carbon Dioxide)	-	30000	-
16(Thermal efficiency of Water Heater shall not be less nthan 62%)	-	30000	-
15(The later circuit shall be kept under pressure for minimum 5 min.)	-	30000	-
15(All water carrying parts of the appliance, individually and when assembled to form the water circuit of the appliance shall not leak or show any permanent distortion during or after the test when tested at a hydrostatic pressure 4 kgf/cm2)	-	30000	-
14(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	30000	-
12(The Appliance shall be provided with a means of adjusting water rate.)	-	30000	-
11(The gas supply shall be restored manually.)	-	30000	-
11(The Water heater shall be provided with a suitable overheat protection device, which shall switch off the supply of gas, if the temperature of the delivered water reaches 80°C max. )	-	30000	-
10(The ignition to the burners from pilot shall be smooth)	-	30000	-
10(It is essential that the pilot flame shall be seen either directly or by reflection.)	-	30000	-
10(The pilot burner shall be made of a material that shall not deteriorate under normal condition of use)	-	30000	-
10(While in operation the relative position of the pilot and burner shall not alter.)	-	30000	-
10(The pilot shall be positioned in such a way that their products of combustion are evacuated with those of the burner)	-	30000	-
10(An appliance shall have an ignition device, where the appliance is provided in the form of a pilot it shall be possible to light it easily with a matchstick or a special ignition device)	-	30000	-
9.1(The Appliance shall have a flame failure device, controlling the admission of gas to the main burner and possibly to any ignition pilot. The provisions given in 14.1 of IS:5116 shall apply.)	-	30000	-
8(The device shall be of such a design that gas shall not enter to the main burner and the pilot (if provided) until it is reset to the original position.)	-	30000	-
8(The Appliance shall have a device allowing manual interruption of the supply of gas to the burner and pilot, if available in case of exigency.)	-	30000	-
7(All Appliances shall be designed so that ignition, correct burner performance and the length of the pilot flames. If any , can always be easily seen. This visibility shall be assumed at all times and particularly, where there is a viewing window, this shall not deteriorate under the effect of heat.)	-	30000	-
6.6(Gas Inlet Connections : The water heater shall be provided with nozzle or screwed gas inlet connection as given in 18 of IS:5116)	-	30000	-
6.5(The gas and water connections shall be situated at the base of the appliance. it shall be possible to connect the appliance to supply, which are in a plane parallel or perpendicular to the wall on which the appliance is fixed.)	-	30000	-
6.4(The water inlet and outlet connection shall be of 1/2" BSP thread.)	-	30000	-
6.3(All water connection shall be of copper or brass tube and have at least 6 mm inner diameter and 0.5 mm nominal wall thickness of the tube.)	-	30000	-
6.2(Gas inlet connection shall permit a rigid connection.)	-	30000	-
6.2(Gas inlet connection shall permit a rigid connection.)	-	30000	-
6.1(For connections and screws other than for water, metric threads shall be used. )	-	30000	-
5.5(Diaphragm if provided for inlet water control device, shall be made of synthetic rubber.while choosing the material, the manufacturer shall take into account the characteristics required for the satisfactory use that is , mechanical and chemical stability. Material selected shall not degrade under normal working conditions.)	-	30000	-
5.4(Melting point of metal for burner top)	-	30000	-
5.4(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	30000	-
5.3(Change in weight or volume of a non metallic material, when immerse in n-Pentane for 72 hours)	-	30000	-
5.2(The copper and copper alloy forged and cast parts shall pass the mercurous nitrate test (Season cracking test) when tested according to the method specified in IS:2305.)	-	30000	-
5.1(The material used in the construction of the water heater shall be resistant to wear and deterioration occuring in the normal use.)	-	30000	-
4.1.12(All heat exchanger tubes through which the water passes and water chamber, if provided, shall be completely filled with water before igniting the burner.)	-	30000	-
4.1.11(The water heater shall have a provision such that supply of gas shall be cut off and the burner extinguished after 20+1/-2 min of uninterrupted use. The appliance shall able to restart manually.)	-	30000	-
4.1.10(The Appliance shall be provided with a safety device, which cuts off the supply of gas in case water dose not flow or stops flowing while in operation.)	-	30000	-
4.1.9(The gas (heat) input to the pilot alone shall not exceed 8 l/h at a gas inlet pressure of 21 mbar and at temperature 25-30°C, wherever applicable.)	-	30000	-
4.1.8(Interior surfaces shall be of such material or so protected, so as to avoid contamination of the contents.)	-	30000	-
4.1.8(All parts of gas water heaters subject to direct heat shall have brazed or welded joints.)	-	30000	-
4.1.7(it shall be possible to install an appliance intended to be fixed to a wall with appropriate means of fixing, such as clamps, hooks, Screws, etc. )	-	30000	-
4.1.6(The gas and water soundness shall be assured after reassemble maintenance.)	-	30000	-
4.1.5(It shall not be possible to replace to replace parts, which are removable for maintenance in a way that could impair the safe performance of the appliance.)	-	30000	-
4.1.4(it shall be possible to clean without difficulty)	-	30000	-
4.1.3(All Parts shall be made and so assembled that the performance characteristics of the appliance will not alter significantly during reasonable life and in normal conditions of installation and use.)	-	30000	-
4.1.2(All parts in contact with water shall be made of such a material that shall not pollute water.)	-	30000	-
4.1.1(No PNG regulator shall be included as a part of the instantaneous domestic gas water heater.)	-	30000	-
4.1(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	30000	-
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	30000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 2553 : Part 1 (2018)

Safety glass - Specification: Part 1 architectural, building and general uses (Fourth Revision)

ALL

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Types)	-	20000	-
5.1.1(General)	-	20000	-
5.1.2(Optical Faults-IS 14900)	-	20000	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	20000	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	20000	-
5.1.2(Linear / Extended Faults -IS 14900)	-	20000	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	20000	-
5.2.2.1( Dimensions- Width )	-	20000	-
5.2.2.1( Dimensions- Length)	-	20000	-
5.2.2.2( Squareness)	-	20000	-
5.2.3 (Fragmentation Test- IS 17004)	-	20000	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	20000	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	20000	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	20000	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	20000	-
5.2.4.1 (Other distortions)	-	20000	-
5.2.5.1( Resistance to shock- IS 17004)	-	20000	-
5.2.5.2( Resistance to human impact- IS 17004)	-	20000	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	20000	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	20000	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	20000	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	20000	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	20000	-
5.3.2.1( Dimensions and squareness- Width )	-	20000	-
5.3.2.1( Dimensions and squareness- Length)	-	20000	-
5.3.2.1( Dimensions and squareness-Squareness)	-	20000	-
5.3.2.2 (Edge displacement)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.4( Boil and Bake Tests-IS 17004)	-	20000	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	20000	-
5.3.6.1( Spot defects in the central area)	-	20000	-
5.3.6.2 (Linear defects in the central area)	-	20000	-
5.3.6.3( Defects in the outer area for framed edges)	-	20000	-
5.3.6.4( Vents)	-	20000	-
5.3.6.5( Creases and streaks)	-	20000	-
5.3.6.6( Defects on edge which will not be framed)	-	20000	-
5.3.7( Humidity Test – Optional)	-	20000	-
5.3.8( Resistance to Human Impact Test)	-	20000	-
4(Types)	-	20000	-
5.1.1(General)	-	20000	-
5.1.2(Optical Faults-IS 14900)	-	20000	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	20000	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	20000	-
5.1.2(Linear / Extended Faults -IS 14900)	-	20000	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	20000	-
5.2.2.1( Dimensions- Width )	-	20000	-
5.2.2.1( Dimensions- Length)	-	20000	-
5.2.2.2( Squareness)	-	20000	-
5.2.3 (Fragmentation Test- IS 17004)	-	20000	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	20000	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	20000	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	20000	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	20000	-
5.2.4.1 (Other distortions)	-	20000	-
5.2.5.1( Resistance to shock- IS 17004)	-	20000	-
5.2.5.2( Resistance to human impact- IS 17004)	-	20000	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	20000	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	20000	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	20000	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	20000	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	20000	-
5.3.2.1( Dimensions and squareness- Width )	-	20000	-
5.3.2.1( Dimensions and squareness- Length)	-	20000	-
5.3.2.1( Dimensions and squareness-Squareness)	-	20000	-
5.3.2.2 (Edge displacement)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.4( Boil and Bake Tests-IS 17004)	-	20000	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	20000	-
5.3.6.1( Spot defects in the central area)	-	20000	-
5.3.6.2 (Linear defects in the central area)	-	20000	-
5.3.6.3( Defects in the outer area for framed edges)	-	20000	-
5.3.6.4( Vents)	-	20000	-
5.3.6.5( Creases and streaks)	-	20000	-
5.3.6.6( Defects on edge which will not be framed)	-	20000	-
5.3.7( Humidity Test – Optional)	-	20000	-
5.3.8( Resistance to Human Impact Test)	-	20000	-
5.2.1(Thickness)	-	20000	-
5.2.2(Dimension and Squarenes)	-	20000	-
5.2.4(Overall Bow)	-	20000	-
5.2.4(Measurement of wave and roller wave)	-	20000	-
5.2.4(Edge lift)	-	20000	-
5.2.4(Local distortion)	-	20000	-
5.2.3(Fragmentation test)	-	20000	-
5.2.7(Four point bending)	-	20000	-
5.2.6(Surface compression)	-	20000	-
5.2.5.1(Resistance to shock)	-	20000	-
5.2.5.2(Resistance to human impact)	-	20000	-
5.3.1(Thickness test)	-	20000	-
5.3.2.1(Dimension and Squarenes test)	-	20000	-
5.3.6(Defects in central area test)	-	20000	-
5.3.6.7(Defects in central area test)	-	20000	-
5.3.5(Fracture and adhesion)	-	20000	-
5.3.8(Resistance to human impact)	-	20000	-
5.3.4(Boil test)	-	20000	-
5.3.4(Bake test)	-	20000	-
5.3.7(Humidity test with condensation)	-	20000	-
5.3.7(Humidity test without condensation)	-	20000	-
5.3.3(Light stability test)	-	20000	-
5.3.2.2(Edge displacement test)	-	20000	-
5.2.2(5.2.2 Dimension and Squarenes test)	-	20000	-
5.2.4(measurement of wave and roller wave)	-	20000	-
5.2.8(Fabrication in Glass)	-	20000	-
Cl. No. 5.2.2.3.1, Table No. 1A(Shape accuracy, girth and length)	-	20000	-
Cl. No. 5.2.2.3.2(Edge straightness deviation)	-	20000	-
Cl. No. 5.2.2.3.3(Maximum cross-curve deviation)	-	20000	-
As per Clause 5.3.9(Laminated Glass)	-	20000	-
As per Clause 5.2.8.2(Toughened)	-	20000	-
As per Clause 5.2.8.4(Toughened)	-	20000	-
As per Clause 5.2.9(Toughened)	-	20000	-
As per Clause 5.3.6.4(Laminated Glass)	-	20000	-
As per Clause 5.3.6.5(Laminated Glass)	-	20000	-
As per Clause 5.3.6.6(Laminated Glass)	-	20000	-
As per Clause 5.5.2.1(Laminated Glass and Glass-Plastic Panes)	-	20000	-
As per Clause 5.5.3.2(Laminated Glass and Glass-Plastic Panes)	-	20000	-
As per Clause 5.6.2(Rigid Plastic Glazing)	-	20000	-
As per Clause 5.7.1(Flexible Plastic)	-	20000	-
As per Clause 3.7(Wind screen and Panes)	-	20000	-
As per Clause 4.1(Wind screen and Panes)	-	20000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 6912 (2005)

Copper and copper alloys forging stock and forging - Specification (Second Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
As per Clause 12.1.1(For Forging Stock)	-	12000	-
As per Clause 12.1.2(For Forging)	-	12000	-
As per Clause 13.1.1(Forging Stock)	-	12000	-
As per Clause 13.1.2(Hot Worked Material)	-	12000	-
As per Clause 13.1.3(Cold Worked Material)	-	12000	-
As per Clause 13.1.4(Cast Material)	-	12000	-
As per Clause 13.1.5(Diameter or Width Across flats greater than 28 mm)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
As per Clause 12.1.1(For Forging Stock)	-	12000	-
As per Clause 12.1.2(For Forging)	-	12000	-
As per Clause 13.1.1(Forging Stock)	-	12000	-
As per Clause 13.1.2(Hot Worked Material)	-	12000	-
As per Clause 13.1.3(Cold Worked Material)	-	12000	-
As per Clause 13.1.4(Cast Material)	-	12000	-
As per Clause 13.1.5(Diameter or Width Across flats greater than 28 mm)	-	12000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 1264 (1997)

Brass gravity die castings - Specification (Fourth Revision)

All

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	8000	-
6.0(Shape)	-	8000	-
6.0(Size)	-	8000	-
6.0(Mass)	-	8000	-
7.0(Cu)	-	8000	-
7.0(Sn)	-	8000	-
7.0(Pb)	-	8000	-
7.0(Ni)	-	8000	-
7.0(Fe)	-	8000	-
7.0(Al)	-	8000	-
7.0(Mn)	-	8000	-
7.0(Si)	-	8000	-
7.0(Total impurities excluding Ni Pb Al Zn)	-	8000	-
9.0(Pressure test)	-	8000	-
11(Marking)	-	8000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 17153 (2019)

Domestic gas stoves for use with piped natural gas (PNG) - Specification

all

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
26(Burner-5)	-	42000	Single Burner SS Body – Rs.20000/- Glass Top – Rs. 23000/- Double Burner SS Body – Rs. 25000/- Glass Top – Rs. 28000/- Three Burner SS Body – Rs. 30000/- Glass Top – Rs. 33000/- Four Burner SS Body – Rs. 35000/- Glass Top – Rs. 38000/- Five Burner SS Body
26(Burner-4)	-	42000	-
26(Burner-3)	-	42000	-
26(Burner-2)	-	42000	-
26(Burner-1)	-	42000	-
25.2(With the Burner lighted on full on, the flame temperature at a height of H+20 mm)	-	42000	-
25.1(Temperature of synthetic rubber diaphragm in gas carrying components)	-	42000	-
25.1(Temperature of the surface in normal use)	-	42000	-
25.1(Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	42000	-
25.1(Rise of Temperature above room temperature in (Wall, Floor, Ceiling), after two hours of operation)	-	42000	-
24(Burner-5)	-	42000	-
24(Burner-4)	-	42000	-
24(Burner-3)	-	42000	-
24(Burner-2)	-	42000	-
24(Burner-1)	-	42000	-
23(When operated at pressure 20-25 gf/cm2 , there shall be no extinction of flame on any of the burneroperating at the max of the burner, when the appliance is placed in normal current of air with velocity of 2 m/s.)	-	42000	-
22(When operated at pressure 20-25 gf/cm2 , for one at full on position, no soot shall be deposited on burner or on the bottom of the vessel.)	-	42000	-
21(When operated at pressure 20-25 gf/cm2 for half an hour flame shall be reduced to simmer and then brought back to full on, operation shall be repeated five times, no flash back shall occur during the test.)	-	42000	-
20(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	42000	-
19.3(Fixed Min Pilot flame shall be sufficient to relight the main burner at the 21 mbar gas inlet pressure.)	-	42000	-
19.2(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	42000	-
19.1.1(When the gas consumption of the burner is reduced to simmer after operating half an hour on full ON flame shall not extinguish, blow off, strike back or form soot at 21 mbar gas inlet pressure.)	-	42000	-
19.1(It shall be possible to operate stove with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	42000	-
18.4.1(The flame failure device if provided shall confirm to IS:5116)	-	42000	-
18.3(When the burner is ignited from a pilot flame and/or by an electric/electronic method, the ignition and flame travel shall be smooth at pressure……..)	-	42000	-
18.2(if the flame is applied to any of the outer row of the burner ports when the gas is flowing , flame travel shall be complete……..)	-	42000	-
18.1(Where the burner or burners are lighted by automatic ignition (Battery of flint operated or by a pilot flame , it shall not be possible for gas to be admitted to the main burner without being smoothly ignited by the pilot flame. Each burner should be at room temperature at the begining of the test and should be tested in turn. )	-	42000	-
18.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	42000	-
17.3(When the gas consumption of the burner is reduced to simmer, the flame shall not extinguish, blow off, strike back or form soot, when tested with commercial PNG at 21 mbar gas inlet pressure.)	-	42000	-
17.2(Burner-5)	-	42000	-
17.2(Burner-4)	-	42000	-
17.2(Burner-3)	-	42000	-
17.2(Burner-2)	-	42000	-
17.2(Burner-1)	-	42000	-
17.2(Sim Rating Declared)	-	42000	-
17.1.2(Total Gas Consumption)	-	42000	-
17.1(Burner-5)	-	42000	-
17.1(Burner-4)	-	42000	-
17.1( Burner-3)	-	42000	-
17.1( Burner-2)	-	42000	-
17.1( Burner-1)	-	42000	-
17.1(Rating Declared)	-	42000	-
15.2(Fragmentation test of the toughened glass to )	-	42000	-
15.1(Verification of the strength of the gas stove surface of the toughened glass top against thermal stress)	-	42000	-
15(Width wise deflection)	-	42000	-
15(Length wise deflection)	-	42000	-
15(Vertical Deflection)	-	42000	-
14.5(The position of the gas inlet shall allow connection to a gas supply on either side of the appliances, the rear end or bottom is also permitted. It shall be possible to change gas inlet from one side to other side easily by standard tools.)	-	42000	-
14.4(Any other connection made from the main gas rail shall be only metallic.)	-	42000	-
14.4(The external surface of the gas rail shall be treated to resist corrosion)	-	42000	-
14.4(The wall thickness of main gas rail)	-	42000	-
14.4(The pipe/tube used for main gas rail shall be of mild steel)	-	42000	-
14.3(Screwed gas Inlet and outlet connections shall confirm to IS:554, Declared by party)	-	42000	-
14.2((e))	-	42000	-
14.2((d))	-	42000	-
14.2(( c))	-	42000	-
14.2((b))	-	42000	-
14.2(Shape of Nozzles as per fig. 3 : (a))	-	42000	-
14.2(Where Nozzles for flexible tubing are fitted, they shall be so positioned as to facilitate fitting of the tubing and also to prevent heating of the tubing to more than 60°C)	-	42000	-
14.1(Nozzle shall be machined from free cutting brass, MS, SS, Zinc)	-	42000	-
13(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	42000	-
12.1.2(The material of the pan support shall be metallic.)	-	42000	-
12.1.1(Loose Pan support shall be so designed that it is not possible to place them firmly in other than proper position)	-	42000	-
12.1(Prongs of the Support shall have suitable taper to accommodate round bottom pans.)	-	42000	-
12.1(The design of the pan supports shall be such that it is practicable to support a pan of 100 mm diameter over at least one top burner without the use of loose rings and such that 125 mm diameter vessel remains stable over each burner. )	-	42000	-
11.7(The appliance comprising two or more burners shall include one burner having a rating of at least 1450 kCal/hr, based on net calorific value of the gas (When using domestic PNG))	-	42000	-
11.6(For Burners having centre flame, provision shall be made to protect the centre flame from pan resting directly on burner top and smothering the centre flame. )	-	42000	-
11.5(If the burner is made and assembled in two or more parts they shall be so designed to provide proper self locating arrangement so that they are always reassembled to its original design preventing any maladjustment in their assembly. This shall also be applicable for primary air regulators.)	-	42000	-
11.4(If primary air regulators are used, they shall be so designed that they are not easily maladjusted by the user and the construction shall be such that primary air adjustment can be made with the burner in place.)	-	42000	-
11.3(The tightness of the joints in the burner assembly shall not be depended upon adhesives or any kind of packing.)	-	42000	-
11.2(The Burner supports shall be rigid and shall be fixed in their place. Their construction shall ensure the stability of the burners and shall prevent their undue movement in a horizontal plane.)	-	42000	-
11.1(The construction of the burners and the assembly shall allow their dismantling from the supports easily with or without the use of tools)	-	42000	-
10.2(The Size of the jet in Litres per hour of flow of PNG at STP conditions shall be impressed upon it.)	-	42000	-
10.1.1(Injector Jet shall be made of metal , with or without ceramic tip. The melting point of the metal shall not be less than 650°C)	-	42000	-
10.1(Dimension- Threads)	-	42000	-
10.1(Dimension- Projection from the face of mounting, Nominal)	-	42000	-
10.1(Dimension- Across Flats)	-	42000	-
10.1(The Injector Jets shall be fixed calibrated type and it shall not be possible to loosen them without the use of tools.)	-	42000	-
9.12(The noting means adopted shall be sufficiently robust to withstand normal use without distortion or damage.)	-	42000	-
9.11.1(Simmer flame shall be obtained by fixed simmer orifice.)	-	42000	-
9.11(Taps having an 'OFF' position shall have positive stops at the 'OFF' and simmer position except that special purpose taps (for appliance incorporating auto or self ignition device))	-	42000	-
9.1(Screw-down valves shall be so designed that it is impossible to withdraw completely the valve stem in the normal operation of the tap.)	-	42000	-
9.9(Screws nuts etc., which regulate the tension of taps valve or springs shall not loosen in operation of the appliance. It shall not be possible to cause a leak during normal manual operation of tap.)	-	42000	-
9.8(All controls or taps shall be easy to operate at all temperatures normally attained in use)	-	42000	-
9.7(C1)	-	42000	-
9.7(B1)	-	42000	-
9.7(A1)	-	42000	-
9.7(D)	-	42000	-
9.7(C)	-	42000	-
9.7(B)	-	42000	-
9.7(A)	-	42000	-
9.7(Dimension of Taper plugs in off position:)	-	42000	-
9.6(Each taper plug tap shall be spring loaded to maintain a gas tight fit. Helical springs fitted in taps and valves shall have flattened ends, which shall be rounded before fitting.)	-	42000	-
9.5.1(Taps shall be lubricated with suitable grease, resistant to the action of the gas and capable of operating at the maximum temperature of 110°C.)	-	42000	-
9.5(Taps shall be so made that in normal use and reasonable application of lubricant, the gas passages do not become blocked.)	-	42000	-
9.4(Preferably all taps (Excluding pilot taps) should lock in the off position, but in all cases it shall be impossible to handle or tap to move accidentally…. )	-	42000	-
9.3(When Taps are fitted with adjustable stops, there shall be means of looking the stops in position. If screws are used for this purpose, they shall not lead into gas passages.)	-	42000	-
9.2(Taps shall be designed so that when placed in any position and viewed from a distance of 3 m, will definitely indicate whether the valve is open, closed or in intermediate position.)	-	42000	-
9.2(All Taps shall close in the same direction. The direction of rotation of knob from off-on-simmer shall be anti-clockwise.)	-	42000	-
9.2(The 'ON' "OFF" and any fixed position of tap handles shall be clearly and durably indicated or shall be obvious by design or position else some indication shall be provided.)	-	42000	-
9.1(The Appliance shall have at least one tap for each burner)	-	42000	-
8.7(The external Finished surfaces shall be easily cleanable.)	-	42000	-
8.6(All springs, screws, nuts and bolts which are visible or to be removed for maintenance, shall be of corrosion-resistant material or treated to resist corrosion.)	-	42000	-
8.5(Concealed Gas Supplies: Concealed tubular fittings liable to corrode shall be protected by bituminous paint or other equally protective material.)	-	42000	-
8.4 (b)(Resistance to Heating)	-	42000	-
8.4 (a)(Resistance to Abrasion)	-	42000	-
8.3.3(Corrosion Resistance test)	-	42000	-
8.3.2(Adhesion Test)	-	42000	-
8.3.1(Thickness of Chromium coating)	-	42000	-
8.3(Thickness of Nickel coating of the top flat surface of the body of electroplated stove.)	-	42000	-
8.2(Vitreous enameled component shall meet the requirement when tested in accordance with Annex E of IS:5116)	-	42000	-
8.1(The finishes shall, on visual examination, show no defects, such as pin-holes, blisters, roughness or exposed area of metal, which give rise to undualy rapid deterioration in use.)	-	42000	-
8.1(Parts, which will come in contact with the foodstuff, shall be capable of being hygienically cleaned.)	-	42000	-
8.1(The Finish of exposed parts shall be durable, easy to clean and not subject to excessive deterioration in normal use.)	-	42000	-
7(Rigidity and Stability : The appliance shall be so designed that it remains stable and shall not be easily overturned.)	-	42000	-
6.7(Thickness of Sheet)	-	42000	-
6.6(All nuts, bolts and fittings having spanner flats shall be capable of being moved by suitable spanner or be readily accessible to an adjustable spanner.)	-	42000	-
6.5(Parts, which are intented to be removable by the user, shall be easy to replace correctly and difficult to assemble incorrectly.)	-	42000	-
6.4(Burners and parts of Burner only of same rating , model and make shall be interchangeable or replaceable without effecting performance.)	-	42000	-
6.3(Burner ports shall be so designed and located that in normal use spilage of food shall not cause internal fouling of mixing tube and or blockage of injector jet.)	-	42000	-
6.2(The relative distance between the centres of the adjoining burner-)	-	42000	-
6.2(the parts of the burner shall not become disconnected during operation of the appliance.)	-	42000	-
6.1(The appliance, including all the component parts, shall be easy to clean and maintain in good working order, there shall be easy access to the accessories and controls for maintenance and adjustment.)	-	42000	-
5.8.3(The number of glass fragments contained in a 50 mm side square, when tested as Cl. 15.2)	-	42000	-
5.8.3(Toughened glass shall fragment into small particles.)	-	42000	-
5.8.2(Pan support for an uncovered burner in contact with the glass ceramic surface.The surface area of the pan support in contact with the glass ceramic)	-	42000	-
5.8.2(The toughened glass top shall ensure durability against damage in normal use)	-	42000	-
5.8.2(The means to hold the glass top of the gas stove shall not allow any stress or risk of mechanical change to the glass top.)	-	42000	-
5.8.1(Toughened glass top including their edges or corners shall not have fissures or scratches)	-	42000	-
5.7(Drip tray if provided shall be made of non-corrosive material)	-	42000	-
5.6(Meltiing poin of metal used in oven, griller or auxilliary or anyother combination)	-	42000	-
5.6(Melting point of metal for burner top)	-	42000	-
5.5(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	42000	-
5.4(Change in weight or volume of a non metallic material, when immerse in n-Pentane or PNG for 72 hours)	-	42000	-
5.3(Mercurous Nitrate test for copper and copper alloy Parts)	-	42000	-
5.2(The burner parts shall not melt or distort when burner is operated with flames flashed back for half an hour in the mixing tube.)	-	42000	-
5.1.1(Plastic components which are liable to heating (For example, tap handles push buttons etc.) shall be free of fissures, distortion, blemishes and discolouration)	-	42000	-
5.1(The use of low pressure rubber or plastic tubing fitted or pushed on nozzle is not recommended.)	-	42000	-
5.1(If flexible tubing is used, it shall not be fitted on the outlet side of any control which is capable of cutting of the gas completely, except where screwed metal connection are fitted.)	-	42000	-
5.1(The appliance shall be free from swarf, grit and other foreign matters.)	-	42000	-
4.3(No pressure regulator shall be included as part of the stove.)	-	42000	-
4.2(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	42000	-
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	42000	-
4.1(General)	-	42000	-
4.2(General)	-	42000	-
4.3(General)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1.1(Materials)	-	42000	-
5.2(Materials)	-	42000	-
5.3(Materials)	-	42000	-
5.4(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.7(Materials)	-	42000	-
5.8.1(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (b)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (c )(Materials)	-	42000	-
25.2(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (d)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (d)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.2(Combustion)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.1(Combustion)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.1(Combustion)	-	42000	-
5.8.3 (a)(Materials)	-	42000	-
23(Resistance to Draught)	-	42000	-
5.8.3 (b)(Materials)	-	42000	-
5.8.3 (c)(Materials)	-	42000	-
22(Formation of soot)	-	42000	-
21(Flash Back)	-	42000	-
5.8.3 (d)(Materials)	-	42000	-
20(Noise Control)	-	42000	-
5.8.3 (e)(Materials)	-	42000	-
5.8.3 (f)(Materials)	-	42000	-
19.3(Flame Stability)	-	42000	-
6.1(Design for Maintenance)	-	42000	-
19.2(Flame Stability)	-	42000	-
6.1(Design for Maintenance)	-	42000	-
19.1.1(Flame Stability)	-	42000	-
6.2(Design for Maintenance)	-	42000	-
6.2(Design for Maintenance)	-	42000	-
19.1(Flame Stability)	-	42000	-
6.3(Design for Maintenance)	-	42000	-
18.4(Ignition and Flame Travel)	-	42000	-
6.4(Design for Maintenance)	-	42000	-
18.3(Ignition and Flame Travel)	-	42000	-
6.5(Design for Maintenance)	-	42000	-
18.2(Ignition and Flame Travel)	-	42000	-
18.1(Ignition and Flame Travel)	-	42000	-
18.1(Ignition and Flame Travel)	-	42000	-
6.6(Design for Maintenance)	-	42000	-
17.0(Gas Consumption)	-	42000	-
6.7(Design for Maintenance)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
9.11(Gas Taps)	-	42000	-
7.1(Rigidity and Stability)	-	42000	-
7.2(Rigidity and Stability)	-	42000	-
7.3(Rigidity and Stability)	-	42000	-
8.1(Workmanship and Finish)	-	42000	-
8.1(Workmanship and Finish)	-	42000	-
8.2 & 8.2.1(Workmanship and Finish)	-	42000	-
8.3(Workmanship and Finish)	-	42000	-
8.3(Workmanship and Finish)	-	42000	-
8.3.2(Workmanship and Finish)	-	42000	-
8.4 (a)(Workmanship and Finish)	-	42000	-
8.4 (b)(Workmanship and Finish)	-	42000	-
8.5(Workmanship and Finish)	-	42000	-
8.6(Workmanship and Finish)	-	42000	-
8.7(Workmanship and Finish)	-	42000	-
9.1(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.3(Gas Taps)	-	42000	-
9.4(Gas Taps)	-	42000	-
9.5(Gas Taps)	-	42000	-
9.11.1(Gas Taps)	-	42000	-
9.12(Gas Taps)	-	42000	-
10.1(Injector Jets)	-	42000	-
10.1 (a)(Injector Jets)	-	42000	-
10.1 (b)(Injector Jets)	-	42000	-
10.1 (c )(Injector Jets)	-	42000	-
10.1.1(Injector Jets)	-	42000	-
9.5.1(Gas Taps)	-	42000	-
10.2(Injector Jets)	-	42000	-
9.6(Gas Taps)	-	42000	-
11.1(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.2(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.3(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.4(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.5(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.6(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.7(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
9.8(Gas Taps)	-	42000	-
9.9(Gas Taps)	-	42000	-
9.10(Gas Taps)	-	42000	-
12.1(Pan Supports)	-	42000	-
12.1.1(Pan Supports)	-	42000	-
12.1.2(Pan Supports)	-	42000	-
13.1(Gas Soundness)	-	42000	-
14.1(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.3(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 15558 (2024)

INSTANTANEOUS DOMESTIC WATER HEATER FOR USE WITH LPG SPECIFICATION First Revision of IS 15558

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Construction)	-	15000	-
4.1.2(Construction)	-	15000	-
4.1.3(Construction)	-	15000	-
4.1.4(Construction)	-	15000	-
4.1.5(Construction)	-	15000	-
4.1.6(Construction)	-	15000	-
4.1.7(Construction)	-	15000	-
4.1.8(Construction)	-	15000	-
4.1.9(Construction)	-	15000	-
4.1.10(Construction)	-	15000	-
4.1.11(Construction)	-	15000	-
4.1.12(Construction)	-	15000	-
5.1(Materials)	-	15000	-
5.2(Materials)	-	15000	-
5.3(Materials)	-	15000	-
5.4(Materials)	-	15000	-
5.5(Materials)	-	15000	-
6.1(Connections)	-	15000	-
6.2(Connections)	-	15000	-
6.3(Connections)	-	15000	-
6.4(Connections)	-	15000	-
6.5(Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
7(Flame Visibility)	-	15000	-
8(Gas Taps)	-	15000	-
9(Flame Failure Device)	-	15000	-
10(Ignition Device)	-	15000	-
11(Protection Against Accidental Overheating)	-	15000	-
12(Water Rate Adjuster)	-	15000	-
14(Gas Soundness)	-	15000	-
15(Water Soundness)	-	15000	-
16(Thermal Efficiency)	-	15000	-
16(Thermal Efficiency)	-	15000	-
17(Combustion)	-	15000	-
18(Gas Consumption)	-	15000	-
19.1(Ignition and flame travel)	-	15000	-
19.2(Ignition and flame travel)	-	15000	-
19.3(Ignition and flame travel)	-	15000	-
20(Flame Stability)	-	15000	-
21(Noise Control)	-	15000	-
22(Flash Back)	-	15000	-
23(Resistance to Draught)	-	15000	-
24(Fire Hazard And Limiting Temperature )	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
25(Time For Temperature Rise)	-	15000	-
26(Hot Water Output Test)	-	15000	-
27(Marking)	-	15000	-
Cl-4(General Requirements)	-	15000	-
Cl-5.1(water heater)	-	15000	-
Cl-5.2(copper and copper alloy)	-	15000	-
Cl-5.3(Non-metallic materials)	-	15000	-
Cl-5.4(Mixing tube and burner head)	-	15000	-
Cl-6.3(All Water connections)	-	15000	-
Cl-6.4(water inlet and outlet connections)	-	15000	-
Cl-6.6(Gas Inlet Connections)	-	15000	-
Cl-7(Flame visibility)	-	15000	-
Cl-8(Gas Taps)	-	15000	-
Cl-9(Flame failuse device)	-	15000	-
Cl-11(Protection against accidental overheating)	-	15000	-
Cl-13(General condition of test)	-	15000	-
Cl-14(Gas Soundness)	-	15000	-
Cl-15(Water Soundness)	-	15000	-
Cl-16(Thermal efficiency)	-	15000	-
Cl-17(carbon monoxide/carbon dioxide)	-	15000	-
Cl-18(Gas Consumption)	-	15000	-
Cl-19(Ignition and flame travel)	-	15000	-
Cl-20(FLAME STABILITY)	-	15000	-
Cl-21(NOISE CONTROL)	-	15000	-
Cl-22(FLASH-BACK)	-	15000	-
Cl-24("FIRE HAZARDS AND LIMITING TEMPERATURE")	-	15000	-
Cl-25(TIME FOR TEMPERATURE RISE)	-	15000	-
Cl-26(HOT WATER OUTPUT TEST)	-	15000	-

13 May, 2028

-
Included w.e.f.17.06.2025

IS 302 : Part 2 : SEC 31 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 31 range hoods

All

34000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-

13 May, 2028

-
Included w.e.f 02.07.2025 Exclusion: Cl 19.11.4.1-19.11.4.7(EMI/EMC)

Bureau of Indian Standards

The National Standards Body of India

SHRI KRISHNA TEST HOUSE PVT LTD (142)

Plot No.142, Sec-G, Bawana-II, DSIIDC, Bhorgarh industrial area New Delhi, Delhi, North, Delhi, 110040

9266808773 SKTHPL142@GMAIL.COM

Scope List