BIS - LIMS (Laboratory Information Management System)

KPML Low Voltage Rotating Machine and Hydraulic Laboratory Karad Projects and motors Limited

Plot No B67 and 68 Karad Industrial Area MIDC Tasawade Karad, Karad, Satara, Maharashtra, 415109

9850983352 amit.deshpande@kpml.co.in

Scope List

Reset

5 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14220 (2018)

Openwell submersible pumpsets - Specification (First Revision)

Open Well Submersible Pump Set(0.12KW to 45KW)

23526 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Design Features)	-	10000	-
8.1.1(Design Features)	-	10000	-
8.1.4(Design Features)	-	10000	-
8.1.5(Design Features)	-	10000	-
8.1.5(Design Features)	-	10000	-
8.1.7(Design Features)	-	10000	-
10.6.1( Provision for Earthing)	-	10000	-
10.6.2( Provision for Earthing)	-	5000	-
10.6.3( Provision for Earthing)	-	5000	-
10.6.4( Provision for Earthing)	-	5000	-
15.5(Hydrostatic Pressure Test)	-	10000	-
16.1.1( Guarantee of Performance)	-	23526	-
16.1.2( Guarantee of Performance)	-	23526	-
16.1.3( Guarantee of Performance)	-	23526	-
16.1.4( Guarantee of Performance)	-	23526	-
16.1.5( Guarantee of Performance)	-	23526	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1.3(Marking)	-	5000	-
7(Constructional features)	-	10000	-
7.1(It is recognized that a number of materials of construction are available to meet the needs for pumps handling clear, cold water.)	-	23526	-
7.2(Gaskets, seals and packings used for clear, cold water pumps shall conform to the applicable requirements specified in 5.2 of IS 5120.)	-	10000	-
7.3(The motor shall be provided with a breathing attachment like bellows, diaphragm etc; to compensate the volumetric variation of water inside the motor due to change in the temperature.)	-	10000	-
7.4(The motor shall be protected from ingress of well water, sand and other foreign matter by means of cable glands, rubber seals etc.)	-	10000	-
7.5(All materials and components for the motor shall be suitable for application in respect of resistance and mechanical performance to protect it)	-	10000	-
7.6(The rotor of the wet type open well submersible motor and rotor in water filled designed motor shall be provided with suitable coating from corrosion under water. However if suitable anticorrosion additive is added in the water, no separate protection on rotors is necessary.)	-	10000	-
8(Design Features)	-	10000	-
8.1.2(The multi-stage pump shaft may be guided through bearings, the bearings may be provided in stage casing, suction housing and discharge casing, while in case of intermediate bearings, suitable positions may be selected in the overall span.)	-	10000	-
8.1.3(The pump may be equipped with replaceable bearing and wearing ring, wherever provided.)	-	10000	-
8.1.4(The strainer on the suction shall offer the best compromise amongst restraining large solids from entering the pump and containing the suction losses to the minimum.)	-	10000	-
8.1.5(The pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +5 percent and minimum –15 percent of the guaranteed duty point head up to 30 m. Above 30 m, the pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +10 percent and minimum –25 percent of the guaranteed duty point head.)	-	10000	-
14.10.1(Type test)	-	23526	-
14.10.1(a)(Insulation Resistance test)	-	5000	-
14.10.1(b)(High Voltage test)	-	5000	-
14.10.1(c)(Measurement of stator resistance)	-	5000	-
14.10.1(d)(No load test at rated voltage)	-	5000	-
14.10.1(e)(Reduced voltage running up test at no load)	-	5000	-
14.10.1(f)(Locked rotor)	-	5000	-
14.10.1(g)(Breakaway (starting) torque)	-	5000	-
14.10.1(h)(Leakage current test;)	-	5000	-
14.10.1(j)(Temperature rise test at rated voltage)	-	23526	-
14.10.1(k)(Temperature rise test at reduced voltage)	-	23526	-
16.1(Guarntee of Performance)	-	23526	-
16.1.1(The pumpset shall be guaranteed for their performance of the nominal volume rate of flow and the nominal head at the guaranteed duty point. The overall efficiency of the pumpset shall be guaranteed at the declared duty point only.)	-	23526	-
16.1.2(The guarantee shall be deemed to have been met with, if the measured values of head, volume rate of flow and overall efficiency are within the indicated in IS 11346 limits)	-	23526	-
16.1.3(Open well submersible motor shall not get overloaded in the specified operating head range at rated voltage and supply frequency.)	-	23526	-
16.1.4(The pump shall be tested for the operating head range as per 8.1.5.)	-	23526	-
16.1.5(The overloading of motor is that condition when maximum current drawn by the motor exceeds the limit of 1.07 times of the rated motor current)	-	23526	-
16.1.6(The tolerance shall apply to guaranteed duty point only.)	-	23526	-
16.1.7(Performance at rated voltage and supply frequency is actual performance of the set. This is better than performance at rated speed, since in the entire operating head range speed of motor is higher than rated speed, as motor is running in under loaded condition.)	-	23526	-
16.1.8(The manufacturer shall specify the minimum submergence of pump unit at duty point.)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
18.1(Marking)	-	5000	-
16.4.1 (Amendment-1)(Pump efficiency)	-	23526	-
9(Efficiency)	-	23526	-
10(Performance (Cl 17.1 of IS 5120))	-	23526	-
10.7.1(Terminal Marking and Direction of Rotation)	-	5000	-
10.7.2(Terminal Marking and Direction of Rotation)	-	5000	-
10.7.3(Terminal Marking and Direction of Rotation)	-	5000	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	23526	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	23526	-
10(Suction and Delivery Ends (Cl 17.2 of IS 5120))	-	5000	-
10(Suction and Delivery Ends (Cl 17.2.1 of IS 5120))	-	5000	-
10(Fluid Passages (Cl 17.3 of IS 5120))	-	5000	-
10(Draining Plugrs (Cl 17.4 of IS 5120))	-	5000	-
10(Lantern Ring (Cl 17.5 of IS 5120))	-	5000	-
10(Casing (Cl 17.6 of IS 5120))	-	5000	-
10(Impeller (Cl 17.7 of IS 5120))	-	5000	-
10(Shaft (Cl 17.8 of IS 5120))	-	1000	-
10(Shaft Couplings (Cl 17.9 of IS 5120))	-	1000	-
10(Bearings (Cl 17.10 of IS 5120))	-	1000	-
10(Bearings (Cl 17.10.1 of IS 5120))	-	1000	-
10(Bearings (Cl 17.10.2 of IS 5120))	-	1000	-
10( Stuffing Boxes (Cl 17.11 of IS 5120))	-	1000	-
10(Base Plates (Cl 17.12 of IS 5120))	-	1000	-
10(Prime Mover (Cl 17.13 of IS 5120))	-	1000	-
10(Name Plate (Cl 17.14 of IS 5120))	-	1000	-
10(Name Plate (Cl 17.14 of IS 5120))	-	1000	-
10(Name Plate (Cl 17.14 of IS 5120))	-	1000	-
10(Name Plate (Cl 17.14.1 of IS 5120))	-	1000	-
10.2(Casing)	-	5000	-
10.3(Impeller)	-	1000	-
10.4.1(Shaft)	-	1000	-
10.4.2(Shaft)	-	1000	-
12(Cable)	-	1000	-
12.1(Flat/Round cables as per IS694 shall be used)	-	1000	-
12.1.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	1000	-
12.1.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	1000	-
12.1.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	1000	-
12.1.5(If four core cable is used, the fourth core is to be used for earthing.)	-	1000	-
9 (Amendment-1)(EFFICIENCY)	-	1000	-

26 Aug, 2028

-
-

IS 9283 (2013)

Motors for submersible pumpsets - Specification (Second Revision)

Submersible Motors(0.37KW to 75KW)

21205 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Construction, IS 9283)	-	10000	-
5.1.1(Construction, IS 9283)	-	10000	-
5.1.2(Construction, IS 9283)	-	10000	-
5.1.3(Construction, IS 9283)	-	10000	-
5.1.4(Construction, IS 9283)	-	10000	-
5.2.1(Earthing, IS 9283)	-	5000	-
5.2.2(Earthing, IS 9283)	-	5000	-
5.2.3(Earthing, IS 9283)	-	5000	-
5.2.4(Earthing, IS 9283)	-	5000	-
5.2.5(Earthing, IS 9283)	-	5000	-
13(Terminal Markings, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.1(Marking, IS 9283)	-	5000	-
15.3(Marking, IS 9283)	-	5000	-
19(Temperature rise test, IS 9283)	-	21205	-
19(Temperature rise test, IS 9283)	-	21205	-
20(High Voltage test, IS 9283)	-	5000	-
21(Insulation Resistance test, IS 9283)	-	5000	-
22(Speed, IS 9283)	-	21205	-
23(Leakage Current test, IS 9283)	-	5000	-
16.1(c)(Measurement of Stator Resistance)	-	5000	-
16.1(d)(No Load Test)	-	10000	-
16.1(e)(Reduced Voltage running up Test)	-	5000	-
16.1(f)(Locked Rotor test)	-	5000	-
16.1(g)(Full Load Test)	-	21205	-
16.1m(Momentary over-load test)	-	21205	-
16.1 (h)(Performance Characteristics)	-	21205	-
16.2 ( a)(Insulation Resistance)	-	5000	-
16.2 ( b)(Voltage, Time)	-	5000	-
16.2 (c)(Voltage, Current, Power, Frequency, Speed)	-	21205	-
16.2 (d)(Voltgae, Current, Power, Torque)	-	21205	-
16.2 (e)(Voltage, Frequency, Speed)	-	21205	-
5.3(Foreign Matter, IS 9283)	-	500	-
5.5(Finish of Bearings, IS 9283)	-	1000	-
7.1(Dimensions of Motors, IS 9283)	-	2000	-
7.2.1(Tolerances, IS 9283)	-	500	-
7.2.2(Tolerances, IS 9283)	-	500	-
8(Type of duty, IS 9283)	-	500	-
17.1(Performance values, IS 9283)	-	10000	-
17.1(Performance values, IS 9283)	-	10000	-
17.1(Performance values, IS 9283)	-	10000	-
17.1(Performance values, IS 9283)	-	10000	-

26 Aug, 2028

-
Exclusion: Cl 5.6 (Balancing of Rotor, IS 9283), Cl 18.1 (Overload test, IS 9283)

IS 9079 (2018)

Monoset pumps for clear, cold water for agricultural and water supply purposes - Specification (Third Revision)

Monoset Pump for Agricultural Purpose(0.37KW to 25KW)

24467 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(DIRECTION OF ROTATION (Cl 7))	-	5000	-
7.2(DIRECTION OF ROTATION (Cl 7))	-	5000	-
9.1(DESIGN FEATURES (Cl 9))	-	5000	-
9.2(DESIGN FEATURES (Cl 9))	-	5000	-
13.1(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
13.2(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
9.1(DESIGN FEATURES (Cl 9))	-	5000	-
9.2(DESIGN FEATURES (Cl 9))	-	5000	-
13.1(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
13.2(Guarantee and tolerances on Pump Performance (Cl 13))	-	5000	-
7(Contructional Features)	-	10000	-
7.1(Material of Construction)	-	10000	-
7.2(Gaskets.Seals and packings)	-	5000	-
9(Design Features)	-	10000	-
9.1.1(The pump may be equipped with replaceable bearing and wearing ring, wherever provided.)	-	5000	-
9.1.2(The pump shall be capable to perform as per guaranteed duty point at the manometric suction lift as specified in Table 1.)	-	5000	-
9.3(The manufacturer shall have a system of controlling dimensional accuracy within a scheme of fits and tolerance limits. The system shall help interchangeability and fitment at site for replacement spares during subsequent repair and maintenance.)	-	5000	-
9.4(The pump efficiency of monoset pumps at duty point as declared by the manufacturer for 2 and 4 poles shall not be less than given in Fig. 3 to Fig. 6 and beyond this range, the efficiency shall be declared by manufacturer.)	-	15000	-
10.6.2, 10.6.3(Direction of Rotation)	-	5000	-
11.8(Type test)	-	24467	-
11.8.1(a)(Measurement of stator resistance)	-	5000	-
11.8.1(b)(High Voltage test)	-	5000	-
11.8.1(c)(Insulation Resistance test)	-	5000	-
11.8.1(d)(No load test at rated voltage)	-	5000	-
11.8.1(e)(Locked rotor)	-	5000	-
11.8.1(f)(Breakaway (starting) torque)	-	5000	-
11.8.1(g)(Reduced voltage running up test at no load)	-	5000	-
11.8.1(h)(Temperature rise test at rated voltage)	-	24467	-
11.8.1(j)(Temperature rise test at reduced voltage)	-	24467	-
13.1.1(The pumpset shall be guaranteed for their performance of the nominal volume rate of flow and the nominal head at the guaranteed duty point. The overall efficiency of the pumpset shall be guaranteed at the declared duty point only.)	-	24467	-
13.1.2(The guarantee shall be deemed to have been met with, if the measured values of head, volume rate of flow and overall efficiency are within the limits indicated in clause 8 of IS 11346. However, after applying the tolerance, overall efficiency value shall not be less than that derived from Fig. 3 to 6.)	-	24467	-
13.1.3(Monoset motor shall not get overloaded in the specified operating head range at rated voltage and supply frequency.)	-	24467	-
13.1.4(The tolerance shall apply to guaranteed duty point only.)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Marking)	-	5000	-
15.1(Hydrostatic Pressure Test)	-	5000	-
13.5(Minimum Current Requirement)	-	5000	-
13(Guarantee and tolerance on pump performance)	-	5000	-
13.4.1 (Amendment-1)(Pump Efficiency)	-	5000	-
8.2 IS 11346 : 2002(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	5000	-
12.5(Efficiency)	-	24467	-
Cl.8.3 b IS 11346 : 2002(Overall efficiency)	-	24467	-
13.1.1 (8.2 of IS 11346 : 2002)(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
13.1.1 (8.2 of IS 11346 : 2002)(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
12.5(Efficiency)	-	24467	-
Cl.8.3 b IS 11346 : 2002(Overall efficiency)	-	24467	-
Cl13.2.3 IS 9079:2002(Current consumption)	-	24467	-
12.2(Laboratory Test)	-	24467	-
Cl13.2.3 IS 9079:2002(Current consumption)	-	24467	-
8.2 IS 11346 : 2002(Verification of Guarantee Rate of flow and head (Cl.8.2 IS 11346 : 2002))	-	24467	-
10.1(GENERAL REQUIREMENTS Casing)	-	1000	-
10.2(GENERAL REQUIREMENTS Impeller)	-	1000	-
10.3(GENERAL REQUIREMENTS Shaft)	-	1000	-
10(General Requirements)	-	1000	-
10.1(General Requirements(Casing))	-	1000	-
10.2(General Requirements(Impeller))	-	1000	-
10.3(General Requirements(Shaft))	-	1000	-
10.5(Provision of Earthing)	-	1000	-
10.6.1(Terminal Marking)	-	1000	-
8.6.5(If four core cable is used, the fourth core is to be used for earthing.)	-	1000	-
11.1.1(Type of Enclosures)	-	25000	-

26 Aug, 2028

-
Exclusion: Cl 10.4.1, Cl 10.4.2, Cl 10.4.3, v10.4.4 (General Requirements(Balancing))

IS 8034 (2018)

Submersible pumpsets - Specification (Third Revision)

Bore Well Submersible Pump Set(0.37 to 75KW)

23526 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
14(Marking)	-	5000	-
6.1 (a)(Constructional Features)	-	10000	-
6.1 (b)(Constructional Features)	-	10000	-
6.1 (c)(Constructional Features)	-	10000	-
6.1 (d)(Constructional Features)	-	10000	-
6.1 (e)(Constructional Features)	-	10000	-
6.1 (f)(Constructional Features)	-	10000	-
6.2 (a)(Material of construction Part Sub Assembly Shaft Sleeve)	-	10000	-
6.2 (b)(Material of construction Part Sub Assembly Casing wear ring (if provided))	-	10000	-
6.2 (c)(Material of construction Part Sub Assembly Bush)	-	10000	-
6.2 (d)(Material of construction Part Sub Assembly Discharge casing (if provided))	-	10000	-
6.2 (e)(Material of construction Part Sub Assembly Impeller)	-	10000	-
6.2 (f)(Material of construction Part Sub Assembly Pump Bowl/Diffuser)	-	10000	-
6.2 (g)(Material of construction Part Sub Assembly Pump Shaft)	-	10000	-
6.2 (h)(Material of construction Part Sub Assembly Suction Casing)	-	10000	-
6.2.2.1(Gaskets, Seals and Packings)	-	10000	-
6.2.2.2(Gaskets, Seals and Packings)	-	10000	-
6.2.3(Gaskets, Seals and Packings)	-	10000	-
6.2.4(Gaskets, Seals and Packings)	-	10000	-
6.2.5(Gaskets, Seals and Packings)	-	10000	-
7.1.1(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.2(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.3(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.4(Design features: Typical design features 0f components of pump)	-	9999.98	-
7.1.5(Design features: Typical design features 0f components of pump)	-	10000	-
7.1.6(Design features: Typical design features 0f components of pump)	-	10000	-
8.7.1(Direction of Rotation)	-	5000	-
8.7.2(Direction of Rotation)	-	5000	-
10.3(Hydrostatic Pressure Test)	-	5000	-
11.1.1(Guarantee of Performance)	-	23526	-
11.1.2(Guarantee of Performance)	-	23526	-
11.1.2(Guarantee of Performance)	-	23526	-
11.1.3(Guarantee of Performance)	-	23526	-
11.1.4(Guarantee of Performance)	-	23526	-
11.1.5(Guarantee of Performance)	-	23526	-
6(Measurement of shaft extension)	-	5000	-
6(Constructional Features)	-	10000	-
11(Guarantee of Performance)	-	23526	-
10(Pump Performance test)	-	23526	-
9.1(General)	-	23526	-
9.10 (a)(Insulation Resistance test)	-	5000	-
9.10 (b)(High Voltage test)	-	5000	-
9.10 (c)(Measurement of Stator Resistance)	-	5000	-
9.10 (d)(No Load Test at Rated Voltage)	-	5000	-
9.10 (e)(Reduced voltage Running up test)	-	5000	-
9.10 (f) & (g)(Locked Rotor Test)	-	5000	-
9.10 (h)(Leakage current test)	-	5000	-
9.10 (j)(Temperature Rise Test at Rated Voltage)	-	23526	-
9.10 (k)(Temperature rise test at reduced voltage)	-	23526	-
7.1.7(Pump loading shall be as per 11.1.5)	-	23526	-
7.1.9(prime mover electric motor suitable for the pumps shall be of contineous duty as specified in IS/IEC 60034-4 and as per IS 9283)	-	23526	-
9.10 m(Momentary over-load test)	-	23526	-
9.8(Speed)	-	23526	-
9.7(Breakaway (Starting)Torque Test)	-	10000	-
10.2.1(Measurement of Total Head)	-	23526	-
10.2.2(Flow Measurement)	-	23526	-
8.7(Direction of Rotation)	-	5000	-
7(Design features)	-	10000	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	23526	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	23526	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	23526	-
7.1.10(Voltage & Frequency variation)	-	23526	-
8.1(General Requirements)	-	2000	-
8.2(Casing)	-	2000	-
8.3(Impeller)	-	2000	-
8.4.1(Shaft)	-	2000	-
8.4.2(Shaft)	-	2000	-
8.8(Terminal Marking)	-	2000	-
8.9.1(Typical Installation)	-	2000	-
8.9.3(Typical Installation)	-	2000	-
12(Guarantee of workmanship and material)	-	2000	-
8.9(Typical installation)	-	2000	-
8.6(Submersible cable)	-	2000	-
8.6.1(Flat/Round cables as per IS694 shall be used)	-	2000	-
8.6.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	2000	-
8.6.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	2000	-
8.6.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	2000	-
8.9(Installation)	-	2000	-
8.9.2(The pumpset shall be installed as per guidelines laid down in IS 14536 or as per the recommendation of the manufacturer)	-	2000	-
8.9.4.1(Earthing of the motor shall be done as per IS 9283 in accordance with the relevant provisions of IS 3043.)	-	2000	-
8.9.4.2(In case of PVC pipes used as discharge pipe, a separate non corrosive, low resistance conductor from motor earth terminal to control panel earth terminal shall be provided for earthing.)	-	2000	-
8.9.4.3(In case non corrosive GI pipes and clamps are used for the purpose of earthing the motor, earthing connection may be made to the discharge pipe clamp and to the control panel earth terminal)	-	2000	-
8.1(GENERAL REQUIREMENTS)	-	2000	-

26 Aug, 2028

-
Exclusion: Cl 8.5.1 (Balancing), Cl 8.5 (Balancing of rotor), Cl 8.8 (Terminal Marking), Cl 8.9.1 (Typical Installation), Cl 8.9.3 (Typical Installation), Cl 12 (Guarantee of workmanship and material), Cl 8.6 (Submersible cable), Cl 8.9.4c (Earthing)

IS 8472 (2019)

Centrifugal regenerative pumps for clear, cold water - Specification (Second Revision)

Regenerative self priming pumps 0.18-3.7 kW

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Marking)	-	5000	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	5000	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	5000	-
12.3(Hydrostatic Pressure Test)	-	5000	-
12.4(Pump tests)	-	5000	-
12.5(Self-Priming Test for Self-Priming Pumps)	-	5000	-
13.1.2(No Load Test at Rated Voltage)	-	5000	-
13.1.2.1.1(Temperature Rise Test at Rated Voltage)	-	5000	-
13.1.2.1.2(Temperature Rise Test at Reduced Voltage)	-	5000	-
13.1.2(Break away torque Pull up torque)	-	5000	-
13.1.2(High Voltage test)	-	5000	-
13.1.2(Insulation Resistance)	-	5000	-
8(Direction of Rotation)	-	5000	-
7(Material of Constructional)	-	5000	-
13.1.2(Measurement of stator resistance)	-	5000	-
13.1(Single phase monoset pumps)	-	5000	-
13.1.2(Locked rotor test(cl.6.2(d) of IS 14582))	-	5000	-
13(Tests for Electrical Performance)	-	5000	-
7(Materials of Construction ( Casing/Chamber))	-	5000	-
7(Materials of Construction ( Impeller))	-	5000	-
7(Materials of Construction ( Shaft))	-	5000	-
8.1, 8.2(The direction of rotation of pumps)	-	5000	-
8.3(The direction of inlet and outlet flow passages)	-	5000	-
13.2(Three phase monoset pumps)	-	5000	-
13.2.2(Measurement of stator resistance test (cl.22.3.1(b) of IS 7538))	-	5000	-
13.2.2(No load test (cl.22.3.1cb) of IS 7538))	-	5000	-
13.2.2(Reduced voltage running test (cl.22.3.1(d) of IS 7538))	-	5000	-
13.2.2(Locked Rotor test (cl.22.3.1(e) of IS 7538))	-	5000	-
13.2.2(Insulation Resistance test (cl.22.3.1(m) of IS 7538))	-	5000	-
13.2.2(High Voltage test (cl.22.3.1(n) of IS 7538))	-	5000	-
13.2.2.1.1(Temperature rise test at rated voltage)	-	5000	-
13.2.2.1.2(Temperature rise test at reduce voltage)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
16.1(Marking)	-	5000	-
15.1(Guarantee of Workmanship and Material)	-	5000	-
15.2(Guarantee of Performance)	-	5000	-
15(Guarntee on pump performance and tolerances)	-	5000	-
15.2.1(Monoset pumps)	-	5000	-
15.2.1(a)(Discharge, total head, current and input power at the Guarnteed duty point)	-	5000	-
15.2.1(b)(Non overloading of the prime-mover I the declared operating head range)	-	5000	-
15.2.1(e)(Overall efficiency of pumpset)	-	5000	-
15.2.2(a)(Discharge, total head as per Guarnteed duty point at rated voltage and speed)	-	5000	-
15.2.1(c)(Rated output of motor)	-	5000	-
15.2.1(d)(Full load speed of motor)	-	5000	-
15.2.2(Bare pumps)	-	5000	-
15.2.1(f)(Max.self.priming time)	-	5000	-
15.2.2(b)(Non overloading of the prime-mover I the declared operating head range)	-	5000	-
15.2.2(c)(Non-over-rated prime mover recommended by the manufacturer)	-	5000	-
15.2.2(d)(Max.self.priming time)	-	5000	-
12.3.1(Hydrostatic Pressure Test)	-	5000	-
12.1(Pump Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	5000	-
11(General Requirements)	-	5000	-
10.1(Design Features)	-	5000	-
10.1(a)(Design Features(Voltage Rangings))	-	5000	-
10.1(b)(Design Features(Frequency Rangings))	-	5000	-
10.1(c)(Design Features(Combination of Voltage and frequency variation))	-	5000	-
11.1(The pump shaft should be of adequate size to transmit the required power over the entire head range.)	-	5000	-
11.2(The pump casing should be of robust construction and shall be tested to withstand hydrostatic pressure as specified in 12.3.)	-	5000	-
11.3(The nominal size of suction and delivery pipe of the pump shall be as specified in IS 1239 (Part 1),IS 4984, IS 4985 and IS 12231)	-	5000	-
13(Type of Enclosures)	-	5000	-
11.1(General Requirements)	-	5000	-

26 Aug, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

KPML Low Voltage Rotating Machine and Hydraulic Laboratory Karad Projects and motors Limited

Plot No B67 and 68 Karad Industrial Area MIDC Tasawade Karad, Karad, Satara, Maharashtra, 415109

9850983352 amit.deshpande@kpml.co.in

Scope List