BIS - LIMS (Laboratory Information Management System)

BUNITECH METALLURGICAL SERVICES PRIVATE LIMITED

C 120, Tulsi Estate Plaza, Opp. Bhagyoday Hotel,Changodar, Ahmedabad -382213, Changodar, Ahmadabad, Gujarat, 382213

9426025494 unitech_lab@rediffmail.com

Scope List

Reset

11 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

all type of grades

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl - 9.1,9.5,13.2(Thickness or Diameter)	-	200	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 0.2 MP)	-	1500	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 1.0 MP)	-	1500	-
Cl - 9.1,9.5,13.2(Tensile Strength)	-	1500	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Long.)	-	1500	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Tr.)	-	1500	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Long.)	-	1000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Tr.)	-	1000	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Delivery Condition)	-	500	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Sensitized Condition)	-	500	-
Cl - 9.1,9.5,13.2(Hardness)	-	1000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture)	-	1500	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	200	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	0	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	200	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	0	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	1500	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	1000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	1000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 450 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 500 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 550 Deg. C)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 100 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 150 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 200 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 250 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 300 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 350 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 400 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 450 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 550 Deg. C.)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	1500	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	1500	-
Cl-7.1, 7.2(C)	-	1500	-
Cl-7.1, 7.2(Si)	-	1500	-
Cl-7.1, 7.2(Mn)	-	1500	-
Cl-7.1, 7.2(P)	-	400	-
Cl-7.1, 7.2(S)	-	400	-
Cl-7.1, 7.2(Cr)	-	400	-
Cl-7.1, 7.2(Ni)	-	400	-
Cl-7.1, 7.2(N)	-	400	-
Cl-7.1, 7.2(Ti)	-	400	-
Cl-7.1, 7.2(W)	-	400	-
Cl-7.1, 7.2(Nb)	-	400	-
cL-7.1, 7.2(Co)	-	400	-
Cl-7.1, 7.2(V)	-	400	-
Cl-7.1, 7.2(Al)	-	400	-
Cl-7.1, 7.2(Boron)	-	400	-
Cl-7.1, 7.2(Tungsten)	-	400	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1((Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.))	-	400	-
Cl 6((freedom from defects))	-	400	-
Cl. 12((dimension and tolerance))	-	400	-
Cl. 14((corrosion resistance))	-	400	-
Cl-7.1, 7.2(Mo)	-	400	-
Cl-7.1, 7.2(Cu)	-	400	-
Cl-7.1, 7.2(Ti: (C + N))	-	400	-

24 Oct, 2028

-
included w.e.f 27.01.2026

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

All type of grade

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	500	-
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	500	-
6(Freedom from defects , IS 6911)	-	0	-
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	1500	-
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	1000	-
10.3(Bend Test - IS 1599)	-	500	-
11,Table 7(Erichsen cupping test-IS 10175)	-	300	-
15(Surface Finish)	-	0	-
17(Dimension and tolerance)	-	200	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Elongation)	-	1500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	200	-
Clause 17 , Table 9 to Table 19(Flatness)	-	200	-
Clause 17 , Table 9 to Table 19(Camber)	-	200	-
Table 1(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Elongation)	-	1500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	200	-
Clause 17 , Table 9 to Table 19(Flatness)	-	200	-
Clause 17 , Table 9 to Table 19(Camber)	-	200	-
Table 1(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Elongation)	-	1500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	200	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Elongation)	-	1500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	200	-
Clause 17 , Table 9 to Table 19(Flatness)	-	200	-
Clause 17 , Table 9 to Table 19(Camber)	-	200	-
Table 1(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	400	-
4(Supply of Material)	-	0	-
19(Marking)	-	0	-
5(Manufacture)	-	0	-
10.1 Amd 2(Yeild Strength)	-	1500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1500	-
10.1 Amd 2(Elongation)	-	1500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	200	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	200	-
Clause 17 , Table 9 to Table 19(Flatness)	-	200	-
Clause 17 , Table 9 to Table 19(Camber)	-	200	-
Table 1(Alumium)	-	400	-
Table 1, Amendment 2(Zirconium)	-	400	-
Table 1, Amendment 2(Tungstun)	-	400	-
Table 1, Amendment 2(Tungstun)	-	400	-
Table 1, Amendment 2(Ce)	-	400	-
Table 1, Amendment 2(Cobalt)	-	400	-
Table 1, Amendment 2(Ta)	-	400	-
5.1 - 1(Carbon)	-	400	-
5.1 - 1(Sulphur)	-	400	-
5.1 - 1(Phosphorus)	-	400	-
5.1 - 1(Manganese)	-	400	-
5.1 - 1(Silicon)	-	400	-
5.1 - 1(Nitrogen)	-	400	-
5.1 - 1(Copper)	-	400	-
5.1 - 1(Titanium)	-	400	-
5.1 - 1(Aluminium)	-	400	-
5.1 - 1(Niobium)	-	400	-
5.1 - 1(Nickel)	-	400	-
5.1 - 1(Chromium)	-	400	-
5.1 - 1(Molybdenum)	-	400	-
6(Freedom from defect)	-	0	-
10.1 - 4(Tensile Test)	-	1500	-
10.1 - 4(Yield strength)	-	1500	-
10.1 - 4(Elongation % on 50mm)	-	1500	-
10.2(Hardness Test)	-	1000	-
10.3(Bend Test)	-	500	-
11(Erichsen Cupping Test)	-	300	-
17(Dimension and tolerance)	-	200	-
12(Corrosion resistance)	-	500	-
5.1 - 1(Carbon)	-	400	-
5.1 - 1(Sulphur)	-	400	-
5.1 - 1(Phosphorus)	-	400	-
5.1 - 1(Manganese)	-	400	-
5.1 - 1(Silicon)	-	400	-
5.1 - 1(Nitrogen)	-	400	-
5.1 - 1(Copper)	-	400	-
5.1 - 1(Titanium)	-	400	-
5.1 - 1(Aluminium)	-	400	-
5.1 - 1(Niobium)	-	400	-
5.1 - 1(Nickel)	-	400	-
5.1 - 1(Chromium)	-	400	-
5.1 - 1(Molybdenum)	-	400	-
6(Freedom from defect)	-	0	-
10.1 - 4(Tensile Test)	-	1500	-
10.1 - 4(Yield strength)	-	1500	-
10.1 - 4(Elongation % on 50mm)	-	1500	-
10.2(Hardness Test)	-	1000	-
10.3(Bend Test)	-	500	-
11(Erichsen Cupping Test)	-	300	-
17(Dimension and tolerance)	-	200	-
12(Corrosion resistance)	-	500	-
8(Heat Treatment)	-	0	-

24 Oct, 2028

-
included w.e.f 27.01.2026

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Grade- ( CR0 to ISC440W), Thickness- (0.50 to 4.00 mm)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	2500	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.14000.00
8(Mechanical and Physical Properties)	-	1500	-
Cl 8(UTM)	-	1500	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	100	-
Cl 8(UTM)	-	1500	-
Cl 9.5(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	100	-
Cl 8(UTM)	-	1500	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	100	-
7.0(ALUMINIUM)	-	500	-
7.0(MICRO ALLOYS)	-	500	-
7.0(NITROGEN)	-	500	-
7.0(SILICON)	-	500	-
7.0(MANGANESE)	-	500	-
7.0(PHOSPHORUS)	-	500	-
7.0(SULPHUR)	-	500	-
7.0(CARBON)	-	500	-
Cl. 11(Out of square)	-	200	-
Cl. 11(Flatness)	-	200	-
Cl. 11(Camber)	-	200	-
Cl. 11(Width)	-	200	-
Cl. 11(Thickness)	-	200	-
Cl. 8.7(Bake Hardening Index)	-	1000	-
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	1000	-
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	1000	-
Cl. 8.4(Bend Test)	-	400	-
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	600	-
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	300	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	1000	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	1000	-
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	1000	-
Cl. 9 Table 8(Surface roughness)	-	300	-
Cl 11(Length, Width & Thickness)	-	100	-
Cl 10(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 8(UTM)	-	1000	-
Cl 8(UTM)	-	1000	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Thickness (08))	-	100	-
Cl 7(UTM)	-	1000	-
8.1(Mechanical)	-	1000	-
8.2(Cupping test)	-	300	-
8.3(Hardness HRB/HV)	-	500	-
8.4(Bend Test)	-	400	-
8.5(Plastic strain ratio)	-	1000	-
8.6(Tensile strain Hardening component)	-	1000	-
8.7(Black Hardening Index)	-	1000	-
9(Surface finish)	-	0	-
10(Freedom from defects)	-	0	-
13(Marking)	-	0	-
Cl. 7.3(Carbon)	-	500	-
Cl. 7.3(Manganese)	-	500	-
Cl. 7.3(Suphur)	-	500	-
Cl. 7.3(Phosphorus)	-	500	-
Cl. 7.3(Silicon)	-	500	-

24 Oct, 2028

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

Grade-E250 to E650

13500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	200	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.13500.00
Cl 15(Length, Width & Thickness)	-	100	-
Cl 12(Sudden Load Applied)	-	500	-
Cl 11.3(Press)	-	300	-
Cl 7(Workmanship)	-	0	-
Cl 18(Weight)	-	200	-
Cl 15(Length, Width & Thickness)	-	200	-
Cl 12(Sudden Load Applied)	-	400	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	1000	-
Cl 7(Workmanship)	-	0	-
Cl 18(Weight)	-	200	-
Cl 15(Length, Width & Thickness)	-	200	-
Cl 12(Sudden Load Applied)	-	400	-
Cl 11.3(Press)	-	400	-
Cl 10.3(UTM)	-	1000	-
Cl 7(Workmanship)	-	0	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	500	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	100	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	100	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	100	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	100	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	100	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	1000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	500	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 15, 16(Off Centre of Web)	-	200	-
Cl. 15, 16(Flange out of square (I beam))	-	200	-
Cl. 15, 16(Width of flange (I Beam))	-	200	-
Cl. 15, 16(Depth (I Beam))	-	200	-
Cl. 15, 16(Mass (Plate))	-	200	-
Cl. 15, 16(Flange Slope)	-	200	-
Cl. 15, 16(Web Thickness)	-	200	-
Cl. 15, 16(Flange Thickness)	-	200	-
Cl. 15, 16(Out of Square (Flat))	-	200	-
Cl. 15, 16(Width )	-	200	-
Cl. 15, 16(Thickness )	-	100	-
Cl. 15, 16(Sectional Area )	-	100	-
Cl. 15, 16(Camber (Angle))	-	100	-
Cl. 15, 16(Out of Square (Angle))	-	100	-
Cl. 15, 16(Weight)	-	200	-
Cl. 15, 16(Leg Length Difference (Angle))	-	200	-
Cl. 15, 16(Leg Length B (Angle))	-	200	-
Cl. 15, 16(Leg Length A (Angle))	-	200	-
Cl. 15, 16(Toe Radius R2)	-	200	-
Cl. 15, 16(Root Radius R1)	-	200	-
Cl 18(Weight)	-	200	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 12(Sudden Load Applied)	-	400	-
Cl 11.3(Press)	-	300	-
Cl 10.3(UTM)	-	1000	-
Cl 7(Workmanship)	-	0	-
14.2(Grain Size)	-	800	-
14.2(Inclusion)	-	800	-
Cl 7(Workmanship)	-	0	-
Cl 10.3(UTM)	-	1000	-
Cl 11.3(Press)	-	300	-
Cl 12(Sudden Load Applied)	-	400	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 18(Weight)	-	200	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	500	-
Clause 8, Table 1, Note 6(By Calculation)	-	300	-
Clause 7(IS 2062)	-	500	-
Clause 11.3(IS 1599)	-	400	-
Clause 12(IS 1757)	-	500	-
Clause 15, Table 4(IS 2062)	-	400	-
16(Tolerance)	-	100	-
20(Marking)	-	0	-
20(MARKING)	-	0	-
8(Micro Alloying elements)	-	500	-
8(Niobium as Nb)	-	500	-
8(Vanadium as V)	-	500	-
8(Titanium as Ti)	-	500	-
10(Tensile Strength-IS:1608(P1)-22)	-	1000	-
10(Yield Stress-IS:1608(P1)-22)	-	1000	-
10(Elongation on SoA 5.65mm GL)	-	1000	-
15(Mass -SOP MT-23)	-	200	-
15(Sectional Area)	-	200	-
15(Dimension -D)	-	200	-
15(Dimension -B)	-	200	-
15(Thickness - t)	-	100	-
15(Flange Slope)	-	100	-
15(Thickness - T)	-	100	-
15(Radius R1)	-	100	-
15(Radius R2)	-	100	-
15(Mass -SOP MT-23)	-	200	-
15(Sectional Area)	-	100	-
15(Dimension -D)	-	200	-
15(Dimension -B)	-	200	-
15(Thickness - t)	-	100	-
15(Thickness - T)	-	100	-
15(Radius R1)	-	100	-
15(Radius R2)	-	100	-
15(Mass -SOP MT-23)	-	200	-
15(Sectional Area)	-	100	-
15(Dimensions AxB)	-	100	-
15(Thickness - t)	-	100	-
15(Radius -R1)	-	100	-
15(Radius -R2)	-	100	-
15(Diameter)	-	100	-
15(Sectional Area)	-	100	-
15(Mass per metre)	-	200	-
15(Mass per metre)	-	200	-
15(Ovality)	-	100	-
15(Side Width)	-	200	-
15(Sectional Area)	-	100	-
15(Mass per metre)	-	200	-
15(Out of Square)	-	100	-
9(Preparation of test sample)	-	0	-
Clause 8, Table 1, Note 2(Aluminium)	-	500	-
Clause 8, Table 1, Note 5(Niobium)	-	500	-
Clause 8, Table 1, Note 5(Titanium)	-	500	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	500	-
Clause 8, Table 1, Note 6(Boron)	-	500	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	500	-
Clause 7(Freedom from Defect)	-	0	-
Clause 11.3(Bend Test)	-	400	-
Clause 12(Impact Test)	-	500	-
Clause 15, Table 4(Dimension)	-	200	-
5(General Requirements)	-	0	-
4(MARKING)	-	0	-
Cl 10.3(UTM)	-	1000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	500	-
Clause 8, Table 1, Note 5(By Calculation)	-	200	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	500	-

24 Oct, 2028

-
Exclusion: Cl.13 (Y Groove Cracking Test), Cl.14.1 (Soundness Test)

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

Grade-(Fe 415, Fe 415D, Fe 415S Fe 500, Fe 500D, Fe 500S Fe 550, Fe 550D Fe 600 Fe 650 Fe 700) & (Dia.-6 to 25 mm)

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	1000	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.15,800/-
Cl 9.3(Load In One Direction)	-	1000	-
Cl 7.2(Weight)	-	300	-
Cl 6.1(Length, Width & Thickness)	-	300	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
Cl 9.4(Load In Other Direction From Bend)	-	1000	-
Cl 9.3(Load In One Direction)	-	1000	-
Cl 7.2(Weight)	-	300	-
Cl 6.1(Length, Width & Thickness)	-	300	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
Cl 9.4(Load In Other Direction From Bend)	-	1000	-
Cl 9.3(Load In One Direction)	-	1000	-
Cl 8.1(UTM)	-	0	-
Cl 7.2(Weight)	-	300	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	500	-
4.1(Sulphur and phosphorous)	-	500	-
4.1(CE)	-	500	-
4.1( Nitrogen%)	-	500	-
4.1(Ni)	-	500	-
4.1(Mo)	-	500	-
4.1(Cr)	-	500	-
4.1( Ti)	-	500	-
4.1(V)	-	500	-
4.1( Nb)	-	500	-
4.1( Aluminium %)	-	500	-
4.1( Copper %)	-	500	-
4.1(Silicon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Manganese %)	-	500	-
4.1(Carbon %)	-	500	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	400	-
Cl. 9.3, Table 4(Bend Test )	-	400	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 7.2 Table -2 (Nominal Mass)	-	300	-
Cl. 6.1(Nominal Size)	-	100	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	100	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1001	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	500	-
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	500	-
8.18.1 Table 3(Total elongation at maximum force)	-	500	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
5.7(PullOut (Bond Test))	-	1000	-
4.2(Niobium (Nb))	-	500	-
4.2(Boron (B))	-	500	-
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	500	-
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	500	-
Cl. 5.7(Date of testing of concrete cubes)	-	0	-
Cl. 5.7(Date of casting of concrete cubes)	-	0	-
Cl. 8.1 Table 3(TS/YS Ratio)	-	1000	-
Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs)	-	100	-
Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs)	-	100	-
Cl. 8.1 Table 3(Maximum Extension)	-	500	-
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	500	-
Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A)	-	200	-
Cl. 4.3(Visual Inspection.)	-	0	-
Cl. 5.2(Surface Characteristics)	-	0	-
Clause 9.4(Rebend Test)	-	400	-
Clause 6.3(Effective Cross-sectional Area)	-	100	-
Clause 8.1(Table 3)(Total Elongation at Maximum Force)	-	1000	-
Cl 9.4(Load In Other Direction From Bend)	-	1000	-
Cl 9.3(Load In One Direction)	-	1000	-
Cl 8.1(UTM)	-	0	-
Cl 7.2(Weight)	-	300	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
Cl 5(Deformations and Surface Characteristics)	-	0	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 7.2(Weight)	-	300	-
Cl 8.1(UTM)	-	0	-
Cl 9.3(Load In One Direction)	-	1000	-
Cl 9.4(Load In Other Direction From Bend)	-	1000	-
13(Identification and marking)	-	0	-
5.7(Pull-out test - IS:2770(P1))	-	1000	-
7.0 & 7.1(Specified lengths - SOP MT-23)	-	100	-
8.0 & 8.1("Total elongation at maximum force on 5.65 vSo mm GL. ")	-	500	-
4.3(Rolling and cold working of bars/wire)	-	0	-
7.1(Specified length)	-	100	-
9.1(Preparation of test sample)	-	0	-
9.2(Tensile test,IS:1608(Pt1)-2018)	-	1000	-
Clause 4.2 Note 2, Amendment 1 & 3(Nb+V+B+Ti)	-	500	-
Clause 4.2 Note 3, Amendment 1 & 3(Cr+Cu+Ni+Mo+P)	-	500	-
Clause 4.2, Amendment 3 Note 4("In order to ascertain whether sufficient quantities of nitrogen binding elements are present, following formula may be used, where all elements are in ppm. (N−120)< (Al free/10)+((Ti+V)/7)+(Nb/14)")	-	500	-
1()	-	0	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	500	-
9.5(Retest)	-	0	-
12(Inspection)	-	0	-

24 Oct, 2028

-
-

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

Diameter-0.125 mm to 12.5mm Diameter

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 AND AS PER IS 7887(ALUMINIUM)	-	500	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.6,500/-
6 AND AS PER IS 7887(PHOSPHORUS)	-	500	-
6 AND AS PER IS 7887(SULPHUR)	-	500	-
6 AND AS PER IS 7887(MANGANESE)	-	500	-
6 AND AS PER IS 7887(SILICON)	-	500	-
6 AND AS PER IS 7887(CARBON)	-	500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	-
7 & 8(Diameter)	-	100	-
7 & 8(Ovality)	-	100	-
Cl 9(Tensile Test On UTM)	-	1000	-
9.2(Wrapping Test)	-	400	-
9.3(Bend test)	-	400	-
10(Finish)	-	0	-
11(Coating test)	-	200	-
13(Freedom from defects)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	-
Cl 9(Tensile Test On UTM)	-	1000	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 9(Tensile Test On UTM)	-	1000	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	-
Cl 9(Tensile Test On UTM)	-	1000	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
6 AND AS PER IS 7887(MICRO ALLOY)	-	500	-
Cl 13(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	-
Cl 9(Tensile Test On UTM)	-	1000	-
Cl 11(Workmanship)	-	0	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	500	-
14(Packing)	-	0	-
15(Marking)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Cl 11(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	-

24 Oct, 2028

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Diameter-2.5 mm to 10 mm

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	0	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.7500.00
Clause 3.1.1(Sulphur)	-	500	-
Clause 3.1.1(Phosphorus)	-	500	-
Clause 3(Nitrogen)	-	500	-
Cl 5 & 6(Diameter)	-	100	-
Cl. 7.1(Elongation)	-	1000	-
Cl. 7.1(Proof Stress 0.2 %)	-	500	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Clause 8.3(Reverse Bend test)	-	200	-
Cl 7(UTM)	-	0	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	200	-
Cl 4.1(Workmanship)	-	0	-
Cl 5 & 6(Diameter)	-	100	-
Cl 7(UTM)	-	0	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	100	-
Cl 4.1(Workmanship)	-	0	-
Cl 5 & 6(Diameter)	-	100	-
Cl 7(UTM)	-	0	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	100	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	100	-
Cl 7(UTM)	-	0	-
Cl 5 & 6(Diameter)	-	100	-
Clause 8.3(IS 1716)	-	100	-
Clause 7.1(IS 1608 Part 1)	-	1000	-
Clause 8.3(IS 1716)	-	100	-
Clause 7.1(Ultimate tensile stress)	-	1000	-
10(Marking)	-	0	-
7.0 & 7.1(Elongation on SoA 5.65mm GL - IS: 1608 (P1))	-	1000	-
7.0 & 7.1(0.2% Proof Strength - IS: 1608 (P1))	-	1000	-
Cl. 6.2(Length)	-	200	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	1000	-
Clause 7.1(Proof Stress (0.2 percent ))	-	1000	-
Cl 4.1(Workmanship)	-	0	-
Clause 8.3(Reverse Bend test)	-	200	-
Clause 3(Nitrogen)	-	500	-
Clause 7.1(IS 1608 Part 1)	-	1000	-
Clause 8.3(Reverse Bend test)	-	100	-

24 Oct, 2028

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

{Mild steel bars(Grade I/II), Upto and including 20 mm} & {Medium Tensile Steel Bars,Upto and including 16 mm}

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	0	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.7000.00
Clause -4, 4.3(TITANIUM)	-	500	-
Clause -4, 4.2(VANADIUM)	-	500	-
Clause -4, 4.1(NIOBIUM)	-	500	-
Clause -4, 4.1(Molybdenum)	-	500	-
Clause -4, 4.1(Chromium)	-	500	-
Clause -4, 4.1(Nickel)	-	500	-
Clause -4, 4.1( ALUMINIUM)	-	500	-
Clause -4, 4.1(SILICON)	-	500	-
Clause -4, 4.1(NITROGEN)	-	500	-
Clause -4, 4.1(MANGANESE)	-	500	-
Clause -4, 4.1(PHOSPHURS)	-	500	-
Clause -4, 4.1(SULPHUR)	-	500	-
Clause -4, 4.1( CARBON)	-	500	-
Clause 5.1(Freedom from Defect)	-	0	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	300	-
Cl 8.2(Bend test)	-	400	-
Clause 8.1(Ultimate Tensile Stress)	-	1000	-
Clause 8.1(Yield Stress)	-	1000	-
Cl. 8.1 Table 1(Elongation)	-	1000	-
Clause 6.1(Size)	-	100	-
7(Tolerance)	-	100	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	200	-
Cl 9.3(Press)	-	0	-
Cl 5.1(Workmanship)	-	0	-
Cl 6.1(Diameter)	-	100	-
Cl 6.2(Weight)	-	300	-
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1000	-
Cl 9.3(Press)	-	0	-
Cl 5.1(Workmanship)	-	0	-
Cl 6.2(Diameter & Ovality)	-	100	-
Cl 6.2(Weight)	-	300	-
Cl 8(Physical Requirements)	-	1000	-
Cl 9.3(Press)	-	0	-
Cl 9.3(Press)	-	0	-
Cl 8(UTM)	-	0	-
Clause 9.3(Bend test)	-	400	-
Cl 6.2(Weight)	-	300	-
Cl 6.2(Diameter & Ovality)	-	100	-
Cl 5.1(Workmanship)	-	0	-
Cl 5.1(Workmanship)	-	0	-
Cl 6.2(Diameter & Ovality)	-	100	-
Cl 6.2(Weight)	-	300	-
Cl 8(UTM)	-	0	-
Cl 9.3(Press)	-	0	-
Cl 4.1(Workmanship)	-	0	-
Cl 5 & 6(Diameter)	-	100	-
Cl 7(UTM)	-	0	-
Clause 5.1(IS 432 Part 1)	-	100	-
Clause 6.2(IS 1732)	-	100	-
Clause 8.1(IS 1608 Part 1)	-	100	-
Clause 4(Any Instrumental Method/Chemical Method)	-	100	-
Clause 4(By Calculation)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(Any Instrumental Method/Chemical Method)	-	100	-
Clause 6.2(Mass)	-	300	-
Clause 8.1(Ultimate Tensile Stress)	-	1000	-
Clause 4(Boron)	-	500	-
Clause 4(By Calculation)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(Copper)	-	500	-
8.1 & 9.2(Yield Strength - IS: 1608 (P1))	-	1000	-
8.1 & 9.2(Elongation on SoA 5.65mm GL - IS: 1608 (P1))	-	1000	-
11(Marking)	-	0	-
Clause 5.1(Freedom from Defect)	-	0	-
Clause 4(Boron)	-	500	-
Clause 4(Carbon Equivalent)	-	500	-
Clause 4(Ni+V+Ti)	-	500	-
Clause 4(Copper)	-	500	-
Clause 4(Copper)	-	500	-
Cl. 8.1 Table 1(Yield Stress)	-	1000	-
Clause 8.1(Elongation)	-	1000	-
Clause 6.2(Mass)	-	300	-

24 Oct, 2028

-
-

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

Grade(304,302,430) & Thickness-(0.5-4.0 mm)

8500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl . 6 .0(Freedom from defect)	-	500	-
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
8.2, Table 3(Proof Stress, N/mm2)	-	1000	-
8.2, Table 3(Tensile Strength, N/mm2)	-	1000	-
8.2, Table 3(Elongation, %)	-	1000	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	1000	-
8.4(Bend Test)	-	500	-
8.5(Erichsen Cupping Test)	-	500	-
10.1(Thickness, mm)	-	500	-
10.2(width, mm)	-	500	-
10.3(Length, mm)	-	500	-
10.4(Flatness,mm)	-	500	-
10.5(Camber, mm)	-	500	-
11(Surface Finish)	-	100	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	1000	-
13(Marking)	-	0	-

24 Oct, 2028

-
-

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

Grade-(1,2,3,4,5,6...10,4M,6M,8M,10M), Diameter-(0.5mm to 40 mm)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	0	For BIS samples: 1.5 times of BIS testing charges, For others:Rs.5,000/-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl 9(Nominal Diameter & Out Of Shape)	-	200	-
Cl 8(Freedom from defects)	-	0	-
Table 1 Note 3(Copper)	-	500	-
Amendment 1(Niobium)	-	500	-
Amendment 1(Vanadium)	-	500	-
Amendment 1(Titanium)	-	500	-
Cl 8(Workmanship)	-	0	-
Cl 9(Nominal Diameter & Out Of Shape)	-	200	-
Cl 9(Nominal Diameter & Out Of Shape)	-	200	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl. 9(Out of Shape)	-	500	-
Cl 9(Nominal Diameter & Out Of Shape)	-	200	-
Cl 8(Workmanship)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Nominal Diameter & Out Of Shape)	-	200	-
Table 1 Note 3(Any Instrumental Method/Chemical Method)	-	100	-
Amendment 1(Micro Alloying Element (Nb+V+Ti))	-	500	-
11(Marking)	-	500	-
9.3(Out of Shape - SOP-MT-23)	-	100	-
9.1(Diameter - SOP-MT-23)	-	200	-
Amendment 1(Micro Alloying Element (Nb+V+Ti))	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(By Calculation)	-	200	-
Table 1 Note 3(Any Instrumental Method/Chemical Method)	-	200	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	200	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	200	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	200	-
Amendment 1(By Calculation)	-	100	-
Table 1 Note 3(Copper)	-	200	-
Amendment 1(Niobium)	-	500	-
Amendment 1(Vanadium)	-	500	-
Amendment 1(Titanium)	-	500	-

24 Oct, 2028

-
-

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

Grade-(N1,N2,N3,N4,N5,N6,N7), Thickness-0.20 to 4.00 mm

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Freedom From Defects)	-	0	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
9.3, Table 3 (Tensile Strength, Mpa)	-	1000	-
9.3, Table 3 (Yield Strength, Mpa)	-	1000	-
9.3, Table 3 (Elongation, %)	-	1000	-
9.4(Erichsen Cupping Test,(Average depth of cupping) mm)	-	400	-
11(Surface finish)	-	0	-
12(Dimensions)	-	100	-
14.1(Thickness,mm)	-	100	-
14.2( Width, mm)	-	100	-
14.3(Length, mm)	-	100	-
14.4(Flatness, mm)	-	100	-
14.5(Camber, mm)	-	100	-
Clause 9.1, 9.2 & Table 3(0.2 Percent Yield Strength)	-	1000	-
17(Marking)	-	0	-
15(Inspection)	-	0	-
14.5(Camber)	-	100	-
14.4(Flatness)	-	100	-
14.3(Length)	-	100	-
14.2.2(Trimmed Edge)	-	100	-
14.2.1(Mill Edge)	-	0	-
14.1(Thickness)	-	100	-
13(Edge condition)	-	100	-
10(Retests)	-	0	-
9.4(Erichsen cupping test)	-	400	-
9.3(Mechanical properties)	-	1000	-
9.2(Tensile test)	-	1000	-
9.1(Sample plan)	-	0	-
8.1.1, table 2(Carbon Silicon Manganese Nickel Chromium Sulphur Phosphorus Copper Nitrogen)	-	500	-
8.1, table 1(C Si Mn Ni Cr S P Cu Ni)	-	500	-
7(Heat treatment)	-	0	-
6(Freedom from defects)	-	0	-
17(Marking)	-	0	-
Clause 9.1, 9.2 & Table 3(IS 1608 Part 1)	-	1000	-
4.1(General requirements)	-	0	-
9.3(Tensile Test-1608:Part 1)	-	1000	-
11(Surface finish)	-	0	-
12(Dimensions)	-	100	-

24 Oct, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

BUNITECH METALLURGICAL SERVICES PRIVATE LIMITED

C 120, Tulsi Estate Plaza, Opp. Bhagyoday Hotel,Changodar, Ahmedabad -382213, Changodar, Ahmadabad, Gujarat, 382213

9426025494 unitech_lab@rediffmail.com

Scope List