BIS - LIMS (Laboratory Information Management System)

CIPET, Hyderabad

IDA Phase II, Cherlapally, Hyderabad, Medchal Malkajgiri, Telangana, 500051

9959333415 cipetptchyd@gmail.com

Scope List

Reset

83 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

upto 150mm

138750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(Classification of pipes)	-	0	25% DISCOUNT ON TEST CHARGES FOR BIS
6.2.1 Annex B(Chloride Content of Resin)	-	4300	25% DISCOUNT ON TEST CHARGES FOR BIS
6.3.1 Annex B(Chloride content)	-	4300	25% DISCOUNT ON TEST CHARGES FOR BIS
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11000	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation charges - 500
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	700	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation charges - 625
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	0	25% DISCOUNT ON TEST CHARGES FOR BIS
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	0	25% DISCOUNT ON TEST CHARGES FOR BIS
7.1.3 (Effective length)	-	0	25% DISCOUNT ON TEST CHARGES FOR BIS
8(Pipe Ends)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
9.1(Visual Appearance)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
9.1(Visual Appearance)	-	250	25% DISCOUNT ON TEST CHARGES FOR BIS
9.2 IS 12235 (Part 3)(Opacity)	-	700	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	3000	25% DISCOUNT ON TEST CHARGES FOR BIS
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700	25% DISCOUNT ON TEST CHARGES FOR BIS
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9.6 IS 12235(Part 14)(Density)	-	700	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation charges - 625
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	850	25% DISCOUNT ON TEST CHARGES FOR BIS
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	4800	25% DISCOUNT ON TEST CHARGES FOR BIS
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	11000	25% DISCOUNT ON TEST CHARGES FOR BIS
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	1000	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation/Conditioning charges - 109500 (disc. not applicable)
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation charges - 500
10.4 IS 12235(Part 19)(Flattening Test)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1300	25% DISCOUNT ON TEST CHARGES FOR BIS Specimen preparation charges - 625

23 Feb, 2027

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl. of Cl.No.6.1,6.2,6.3)
3.2, 3.2.1, Fig 1(Manufacture)	-	500	Specimen preparation charges (discount not applicable)
3.2.2, Fig 1(Dimensions)	-	500	25% BIS discount on test charges
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	0	0

23 Feb, 2027

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (Incl.Cl.No.6.1,6.2,6.3)
3.2, 3.2.1, Fig 2(Manufacture)	-	500	Specimen preparation charges (discount not applicable)
3.2.2, Fig 1, table 1(Dimensions)	-	500	25% BIS discount on test charges
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	25% BIS discount on test charges
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	500	25% BIS discount on test charges
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	500	25% BIS discount on test charges

23 Feb, 2027

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl. of Cl.No.6.1,6.2,6.3)
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500	25% BIS discount on test charges
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	500	Specimen preparation charges (no discount applicable)

23 Feb, 2027

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on Test charges (incl. Cl.No.6.1,6.2,6.3)
3.2(Materials)	-	500	Specimen preparation charges (discount not applicable)
3.3, 3.3.1, Fig 1(Manufacture)	-	0	-
3.3.2, table 1, fig 1(Dimensions)	-	500	25% BIS discount on Test charges
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	500	25% BIS discount on Test charges
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	500	25% BIS discount on Test charges

23 Feb, 2027

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% discount on test charges for BIS (incl. Cl.No.6.1,6.2 & 6.3)
3.2, 3.2.1, Fig 1(Manufacture)	-	500	Specimen preparation charges * 25% discount only on test charges
3.2.2, Fig 1(Dimensions)	-	500	25% discount on test charges for BIS
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	0	-

23 Feb, 2027

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl. Cl.No.6.1,6.2 & 6.3)
3.1(General)	-	0	-
3.2, 3.2.1, Fig 1(Manufacture)	-	500	Specimen prptn charges (discount not applicable)
3.2.2, Fig 1(Dimensions)	-	500	25% BIS discount on test charges
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	0	25% BIS discount on test charges

23 Feb, 2027

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

6050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl.Cl.No.6.1,6.2,6.3)
3.2, 3.2.1, Fig 1(Manufacture)	-	500	Specimen preparation charges (discount not applicable)
3.2.2, Fig 2, table 2(Dimensions)	-	500	25% BIS discount on test charges
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500	25% BIS discount on test charges
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	0	-

23 Feb, 2027

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl. of Cl.No.6.1,6.2,6.3)
3.2, 3.2.1, Fig 2(Manufacture)	-	500	Specimen preparation charges (discount not applicable)
3.2.2, Fig 2, table 2(Dimensions)	-	500	25% BIS discount on test charges
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	25% BIS discount on test charges
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	500	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	500	25% BIS discount on test charges

23 Feb, 2027

-
-

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (incl. cL.No.6.1,6.2,6.3)
3.2, 3.2.1, Fig 2(Manufacture)	-	500	Specimen preparation charges (discount not applicable)
3.2.2, Fig 1, table 1(Dimensions)	-	500	25% BIS discount on test charges
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	25% BIS discount on test charges
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	500	25% BIS discount on test charges
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	500	25% BIS discount on test charges

23 Feb, 2027

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4550	25% BIS discount on test charges (Incl. of Cl.No.6.1,6.2,6.3)
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500	Specimen preparation charges (no discount applicable)
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	500	25% BIS discount on test charges (dimension)
3.2.3(Socket, Measurement)	-	0	25% BIS discount on test charges

23 Feb, 2027

-
-

IS 10951 (2020)

Specification for Polypropylene ( PP ) Materials for Moulding and Extrusion ( Second Revision )

Polypropylene ( PP ) Materials for Moulding and Extrus

20475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.5.1,Table-3 or Clause 6.2.1.1(Melt Mass Flow-Rate (MFR) or Melt Flow Index,g/10min,IS 13360 (Part 4/Sec 1)/ASTM D1238)	-	1100	-
Clause 3.5.2,Table-4 or Clause 6.2.1.2(Flexural Modulus,Mpa,IS 13360 (Part 5/ Sec 7),ASTM D790)	-	1300	Specimen Preparation - 500
Clause 3.5.3,Table-5 or Clause 6.2.1.3(Izod Impact Strength,J/m,IS 13360 (Part 5/Sec 4)/ASTM D256)	-	1300	Specimen Preparation - 500
Clause 6.3.2,Table-8, Sl no.1(Tensile yield strength, Mpa,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	1300	Specimen Preparation - 500
Clause 6.3.2,Table-8, Sl no.1(Elongation at yield, %, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Tensile strength at break, Mpa, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	1300	-
Clause 6.3.2,Table-8, Sl no.1(Elongation at break, percent, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Charpy impact strength, KJ/m2, IS 13360 (Part 5/Sec 5))	-	1300	Specimen Preparation - 500
Clause 6.3.2,Table-8, Sl no.1(Hardness – Rockwell R, Shore D,IS 13360 (Part 5/Sec 13),IS 13360 (Part 5/Sec 11))	-	500	-
Clause 6.3.2,Table-8, Sl no.2(Melting temperature,ᴼC,IS 13360 (Part 6/Sec 10))	-	2000	-
Clause 6.3.2,Table-8, Sl no.2(Temperature of deflection under load,°C,IS 13360 (Part 6/ Sec 3),IS 13360 (Part 6/ Sec 17))	-	1100	Specimen Preparation - 500
Clause 6.3.2,Table-8, Sl no.2(Vicat softening temperature, ᴼC,S 13360 (Part 6/Sec 1))	-	1100	-
Clause 6.3.2,Table-8, Sl no.2(Flammability, mm/min,IS/ IEC 60695-11-10)	-	2900	-
Clause 6.3.2,Table-8, Sl no.3(Volume resistivity,IS 2071 (Part 1))	-	1100	Specimen Prepa - 500
Clause 6.3.2,Table-8, Sl no.3(Surface resistivity,IS 2071 (Part 1))	-	1100	-
Clause 6.3.2,Table-8, Sl no.4(Water absorption,%,IS 13360 (Part 8/ Sec 1))	-	600	Specimen Prepa - 500
Clause 6.3.2,Table-8, Sl no.4(Density,kg/m3,IS 13360 (Part 3/ Sec 10),IS 13360 (Part 3/ Sec 11))	-	700	Specimen charges - 500
Clause 6.4.2(Pigments and colourants, IS 9833, Annex D.1)	-	1700	-
Clause 6.4.2(Overall Migration, IS 9845, Annex D.2)	-	1700	Specimen - 300
6.1(The material shall be uniform and free from foreign matter.)	-	2000	-
Clause 6.3.2,Table-8, Sl no.2(Ignitability (Oxygen index), percent,IS 13360 (Part 6/Sec 19))	-	1200	total rates after 25 % discount + spec charges extra

23 Feb, 2027

-
-

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

Polyethylene Material for Moulding & Extrusion

79525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	700	-
5.2.1.2(MFI)	-	1100	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at yield)	-	1300	Specimen Prep 500
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at yield)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at break)	-	1300	Specimen Prep 500
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at break)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec7)(Flexural modulas)	-	1300	Specimen Prep 500
5.3.2 Table 6 IS 13360 (Part 5/Sec23)(Tear Strength)	-	1300	-
5.3.2 Table 6 IS 13360 (Part 5/Sec6)(Dart Impact strength)	-	850	-
5.3.2 Table 6 IS 13360 (Part 5/Sec4)(Izod/Charpy impact strength)	-	1300	Spec -500
5.3.2 Table 6 IS 13360 (Part 5/Sec11)(Shore Aor D hardness)	-	500	-
5.3.2 Table 6 IS 13360 (Part 11/Sec1)(Coeffiicient of friction)	-	850	-
5.3.2 Table 6 IS 13360 (Part 6/Sec3)(Heat deflection temperature)	-	1100.0	Spec prep-500
5.3.2 Table 6 IS 13360 (Part 6/Sec1)(Vicat softening temperature)	-	1100.0	-
Annex B of IS 4984 5.3.2 Table6(Oxidation induction time)	-	2200.0	-
IS 3396(Surface resistivity)	-	1100	-
IS 3397(Volume resistivity)	-	1100.0	-
5.5.6 IS 2530(Carbon black dispersion)	-	700	-
5.4.3 10 ofIS 2530(Carbon black content)	-	925	-
IS 13360(part8/Sec1)(Water absorption)	-	600.0	Spec -500
5.4.35 15 ofIS 2530(Colour fastness to daylight)	-	19850.0	-
5.4.2 13 ofIS 2530(Colour fastness to water)	-	1750.0	-
5.4.1 12 of IS 2530(Colour bleeding)	-	3800.0	-
IS 13360(part 8/Sec9)(ESCR)	-	1200.0	-
IS 13360(part 9/Sec10)(Colour bleeding)	-	0	-
Annex C of IS4984(Volatile content)	-	700.0	-
4 of IS 7016 (part 8)(Oven ageing)	-	4200.0	-
IS 13360(part 9/Sec8)(Transparency)	-	1500.0	-
IS15827(Natural/artificial weathering)	-	1874000	For 10,700 Hours (at 420 nm, 0.35 W/m2). Amount may vary with exposure hours. Not included in Complete Testing Charges
IS 13360(part 9/Sec7)(Specular gloss)	-	1500.0	-
IS 13360(part 9/Sec5)(Haze or luminious transmittance)	-	1500.0	-
5.5.1(All additives used in the material which is meant for usage in contact with foodstuffs, pharmaceuticals and drinking water are given in IS 16738 for guidance purpose.)	-	0	-
5.5.2(When the products are used in contact with foodstuffs, pharmaceuticals and drinking water, its requirements with respect to the material shall also be met as per 3.3, 3.4 and 3.5 of IS 10146.)	-	2000.0	-
Clause 6.4.2(Pigments and colourants, IS 9833, Annex D.1)	-	17500.0	-
Clause 6.4.2(Overall Migration, IS 9845, Annex D.2)	-	1700	Natural weathering extra cost & discount 25 % on test charges

23 Feb, 2027

-
-

IS 14611 (2024)

Multilayered Cross Laminated Sheets/Tarpaulins/Covers/Agricultural Films â Specification (Second Revision)

Multilayered Cross Laminated Sheets/Tarpaulins/Covers/Agricultural Films

41955.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Workmanship)	-	500.0	Total Test Charges : - 41,955.0 /- 25 % Discount For BIS : - 36,111.0 /-
Cl-6.2, 6.3 & 6.8, Table-1 (i)(Mass per unit area, g/m²)	-	500.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (ii)("Tensile strength1), Min,kg/cm²- (a) Longitudinal direction")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (ii)("Tensile strength1), Min,kg/cm² (b) Transverse direction")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (iii)("After ageing at 70 ºC ± 1 ºC for 168 h, Max, kg/cm2 a)Longitudinaldirection")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (iii)("After ageing at 70 ºC ± 1 ºC for 168 h, Max, kg/cm2 b) Transverse direction")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (iv)("Elongation at break, Min, percent a)Longitudinaldirection")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (iv)("Elongation at break, Min, percent b) Transverse direction")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (v)("Tear strength, Min, g: a)Longitudinaldirection")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (v)("Tear strength, Min, g: b)Transverse direction")	-	1300.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (vi)(Dart impact strength, Min, g)	-	850.0	-
Cl-6.2, 6.3 & 6.8, Table-1 (vii)(Average tensile strengthand elongation at breakafter exposing to UVradiation and weathering,Min, (kgf))	-	11480.0	1300 + 10180/- for UV Exposure.
Cl-6.4(Water Proofness Test)	-	1000.0	-
Cl-6.5(Strength of Joints/Seams)	-	1100.0	-
Cl-6.6(Flex Test)	-	7200.0	3000 + 4200
Cl-6.7(Ease of In-Situ Repair)	-	0.0	-
Cl-7(Fixing of Eyelets (for tarpaulins only))	-	500.0	-
Cl-9(Packing and Marking)	-	0	-
Cl-6.3(Accelerated Ageing Test)	-	4200.0	-
Cl-5(Construction of sheets/tarpaulins/covers/agricultural films)	-	2425.0	-

23 Feb, 2027

-
Included w.e.f 09.10.2025

IS 18166 (2025)

Unplasticized Polyvinyl Chloride PVC-U Threaded Column Pipes for Borewells/Tubewells - Specification

25 - 150 mm, CLASS-1 - 7

30800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(COLOUR)	-	500.0	-
6(CLASSIFICATION)	-	500.0	-
7, Table - 2,3,4,7(DIMENSIONS)	-	2000.0	-
8.3 , Table 5, 6(Basic Thread Dimensions)	-	500.0	-
9.1(Visual Appearance)	-	500.0	-
9.2(Resistance to External Blows at 0 °C)	-	1600.0	1100+500
9.4(Tensile Strength)	-	1800.0	1300+500
9.4(Elongation at Break)	-	0	-
9.6(Izod Impact Strength Test)	-	1600.0	1100+500
9.6(Izod Impact Strength Test)	-	0	-
9.8(Density)	-	700.0	-
9.9(Vicat Softening Temperature)	-	1100.0	-
8.1(Column Pipes)	-	500.0	-
8.2(Column Couplers)	-	500.0	-
8.4(Sealing rings and elements made of elastomeric material such as EPDM,)	-	2500.0	2000+500
9.5 , Table- 9(Ultimate Breaking Load)	-	1600.0	1100+500
9.11(Hydrostatic Pressure Test)	-	850.0	-
9.12(Joint Leak Pressure Test)	-	850.0	-
9.3(Flattening Test)	-	1600.0	1100+500
9.7(Resistance to DCM)	-	1500.0	1000+500
9. 10(Effect on Water Lead (first extraction))	-	3000.0	-
9. 10(Effect on Water Lead (third extraction))	-	0	-
9. 10(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
9. 10(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
9. 10(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-

23 Feb, 2027

-
Included w.e.f.29.09.2025

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

Polyethylene Films and Sheet

14938 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	1000	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.6(Ash content - IS 2508: 2024)	-	950	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.6(carbon black dispersion - IS 2530: 1963)	-	1000	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.1(Appearance)	-	250	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.2(Film Form)	-	250	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.3(Odour)	-	250	25% DISCOUNT ON TEST CHARGES FOR BIS
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
5.2.1.2(Nominal Width)	-	500	25% DISCOUNT ON TEST CHARGES FOR BIS
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	2450	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4500	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4500	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	2450	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	2200	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4500	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	4500	25% DISCOUNT ON TEST CHARGES FOR BIS
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2450	25% DISCOUNT ON TEST CHARGES FOR BIS
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2200	25% DISCOUNT ON TEST CHARGES FOR BIS
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1350	25% DISCOUNT ON TEST CHARGES FOR BIS
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1100	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2200	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2450	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	24500	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	2200	25% DISCOUNT ON TEST CHARGES FOR BIS
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	2450	25% DISCOUNT ON TEST CHARGES FOR BIS
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	2200	25% DISCOUNT ON TEST CHARGES FOR BIS

23 Feb, 2027

-
Included w.e.f 28.07.2025

IS 13487 (2024)

Irrigation Equipment — Emitters — Specification

Emitters

3525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Connections)	-	0	-
Cl-5.2(Emitter Ends)	-	0	-
Cl-5.3(Materials)	-	0	-
Cl-6.1(Test Specimens)	-	0	-
Cl-6.2.1(polyethylene pipe)	-	0	-
Cl-6.2.2("grease or chemicals ")	-	0	-
Cl-6.2.3(water temperature)	-	0	-
Cl-6.3(Accuracy or Measuring Devices)	-	0	-
Cl-7.1(Construction and Workmanship)	-	300.0	25% DISCOUNT FOR BIS
Cl-7.2(Flow Paths in Emitter)	-	300.0	25% DISCOUNT FOR BIS
Cl-7.3(Resistance to Hydrostatic Pressure)	-	1000.0	25% DISCOUNT FOR BIS
Cl-7.4(Emitter Pull-Out)	-	500.0	25% DISCOUNT FOR BIS
Cl-7.4.1(In-Line Emitters)	-	500.0	25% DISCOUNT FOR BIS
Cl-7.4.2(On-Line Emitters)	-	500.0	25% DISCOUNT FOR BIS
Cl-8.1.1(Uniformity of Emission Rate)	-	1000	25% DISCOUNT FOR BIS
Cl-8.1.2(Emission Rate as Function of Inlet Pressure)	-	1000.0	25% DISCOUNT FOR BIS
Cl-8.1.3(Determination of Emitter Exponent)	-	600.0	25% DISCOUNT FOR BIS
Cl-9(Marking)	-	500.0	25% DISCOUNT FOR BIS

23 Feb, 2027

-
Included w.e.f 28.07.2025

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

Polyethylene Pipes for the Supply of Gaseous Fuels

520000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	500	25 % DISCOUNT FOR BIS
4.3(Nominal Diameter)	-	500	25 % DISCOUNT FOR BIS
4.4(Colour)	-	500	25 % DISCOUNT FOR BIS
5.1(Polyethylene compound)	-	6100	25 % DISCOUNT FOR BIS
5.3(Anti-oxidant)	-	0	25 % DISCOUNT FOR BIS
5.4(U-V stabilizer)	-	2500	25 % DISCOUNT FOR BIS
5.7(PE Compound Quality Evaluation)	-	400000	25 % DISCOUNT FOR BIS
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	25 % DISCOUNT FOR BIS
5.6(Resistance to Weathering)	-	36000	25 % DISCOUNT FOR BIS
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	500	25 % DISCOUNT FOR BIS
6.1(Out of Roundness (Ovality))	-	500	25 % DISCOUNT FOR BIS
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	500	25 % DISCOUNT FOR BIS
7(Finish)	-	500	25 % DISCOUNT FOR BIS
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5300	25 % DISCOUNT FOR BIS
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4500	25 % DISCOUNT FOR BIS
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11000	25 % DISCOUNT FOR BIS
8.2(Reversion Test)	-	700	25 % DISCOUNT FOR BIS
8.3(Density)	-	700	25 % DISCOUNT FOR BIS
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	25 % DISCOUNT FOR BIS
8.7(Volatile Matter Content)	-	700	25 % DISCOUNT FOR BIS
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1800	25 % DISCOUNT FOR BIS
8.9(Resistance to Weathering)	-	36000	25 % DISCOUNT FOR BIS
6.4(Length of Pipe)	-	500	25 % DISCOUNT FOR BIS
8.4(Melt Flow Rate (MFR))	-	1100	25 % DISCOUNT FOR BIS
8.5(Pigment Dispersion)	-	700	25 % DISCOUNT FOR BIS
8.10(Slow Crack Growth Rate Test)	-	10800	25 % DISCOUNT FOR BIS
8.11(Squeeze-off)	-	1300	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	700	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(iv) Volatile content)	-	700	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(v) Water content1))	-	700	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	700	25 % DISCOUNT FOR BIS
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	400000	25 % DISCOUNT FOR BIS
5.3(Anti-Oxidant)	-	0	25 % DISCOUNT FOR BIS
5.4(U.V. Stabilizer)	-	2500	25 % DISCOUNT FOR BIS
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	5000	25 % DISCOUNT FOR BIS
5.6(ii) Hydraulic characteristics)	-	36000	25 % DISCOUNT FOR BIS
5.6(iii) Thermal stability (Oxidation induction time))	-	2200	25 % DISCOUNT FOR BIS
6(Dimensions of pipes)	-	1500	25 % DISCOUNT FOR BIS
7(Finish)	-	500	25 % DISCOUNT FOR BIS
8.1(Hydraulic Characteristics)	-	20800	25 % DISCOUNT FOR BIS
8.2(Reversion test)	-	700	25 % DISCOUNT FOR BIS
8.3(Density)	-	700	25 % DISCOUNT FOR BIS
8.4(Melt Flow Rate)	-	1100	25 % DISCOUNT FOR BIS
8.5(Pigment Dispersion)	-	700	25 % DISCOUNT FOR BIS
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	25 % DISCOUNT FOR BIS
8.7(Volatile Matter Content)	-	700	25 % DISCOUNT FOR BIS
8.9(Resistance to Weathering)	-	36000	25 % DISCOUNT FOR BIS
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1800	25 % DISCOUNT FOR BIS
8.10(Slow Crack Growth Rate Test)	-	10800	25 % DISCOUNT FOR BIS
8.11(Squeeze-of)	-	1300	25 % DISCOUNT FOR BIS
10(Marking)	-	0	25 % DISCOUNT FOR BIS

23 Feb, 2027

-
Included w.e.f.22.05.2025

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

66725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions of pipe - i) Outside diameter)	-	750	25 % DISCOUNT FOR BIS
5(Dimensions of pipe - ii) Wall thickness minimum)	-	750	25 % DISCOUNT FOR BIS
6(Visual Appearance)	-	300	25 % DISCOUNT FOR BIS
7.1(Hydraulic Characteristics - Quality test)	-	4800	25 % DISCOUNT FOR BIS
7.1(Hydraulic Characteristics - Acceptance test)	-	1600	25 % DISCOUNT FOR BIS
7.2(Reversion Test)	-	700	25 % DISCOUNT FOR BIS
7.3(Tensile Test- i) Tensile Strength)	-	1100	25 % DISCOUNT FOR BIS
7.3(Tensile Test - ii)Elongation at Break)	-	1100	25 % DISCOUNT FOR BIS
7.4(Fusion Compatibility Test- a) Quality test)	-	4800	25 % DISCOUNT FOR BIS
7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	25 % DISCOUNT FOR BIS
7.5(Density)	-	500	25 % DISCOUNT FOR BIS
7.6(Melt Flow Rate)	-	1100	25 % DISCOUNT FOR BIS
4.2(Carbon black- a)carbon content)	-	925	25 % DISCOUNT FOR BIS
4.2(Carbon black- b) Dispersion of carbon black)	-	700	25 % DISCOUNT FOR BIS
5.1.2(Ovality)	-	750	25 % DISCOUNT FOR BIS
4.3(Anti-oxidant)	-	700	25 % DISCOUNT FOR BIS
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	25 % DISCOUNT FOR BIS
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	25 % DISCOUNT FOR BIS
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	25 % DISCOUNT FOR BIS
3(CLASSIFICATION OF PIPES)	-	500	25 % DISCOUNT FOR BIS
4.1(Quick Coupled Male and Female Couplers)	-	500	25 % DISCOUNT FOR BIS
4.1.3(Workmanship and appearance)	-	300	25 % DISCOUNT FOR BIS
4.1.4(Holding attachments for coupler parts)	-	2625	25 % DISCOUNT FOR BIS
6.1.3(Weldability Test- a) Quality test)	-	4800	25 % DISCOUNT FOR BIS
6.1.3(Weldability Test- b) Acceptance test)	-	1600	25 % DISCOUNT FOR BIS
3(QUICK COUPLED PIPES)	-	300	25 % DISCOUNT FOR BIS
4(QUICK COUPLED FITTINGS)	-	300	25 % DISCOUNT FOR BIS
4.1 (a)(Quick Coupled Male and Female Couplers)	-	300	25 % DISCOUNT FOR BIS
4.1 (b)(HDPE couplers —)	-	300	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	1050	25 % DISCOUNT FOR BIS
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	1050	25 % DISCOUNT FOR BIS
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	375	25 % DISCOUNT FOR BIS
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	4575	25 % DISCOUNT FOR BIS
10(Marking)	-	300	25 % DISCOUNT FOR BIS

23 Feb, 2027

-
Included w.e.f.19.12.2024

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

CPVC fittings

164250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Nominal Size(DN))	-	500	FOR BIS 25 % DISCOUNT
3.2(Nominal Outside Diameter)	-	500	FOR BIS 25 % DISCOUNT
3.3(Mean Inside Diameter of Socket at Entry)	-	500	FOR BIS 25 % DISCOUNT
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	FOR BIS 25 % DISCOUNT
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	FOR BIS 25 % DISCOUNT
3.5(Out-of-Roundness (Ovality))	-	500	FOR BIS 25 % DISCOUNT
3.6(Nominal Wall Thickness)	-	500	FOR BIS 25 % DISCOUNT
3.7(Minimum Wall Thickness)	-	500	FOR BIS 25 % DISCOUNT
3.8(Tolerance)	-	500	FOR BIS 25 % DISCOUNT
3.9(Working Pressure)	-	0	FOR BIS 25 % DISCOUNT
3.1(Standard Dimension Ratio)	-	0	FOR BIS 25 % DISCOUNT
3.11(Type Tests)	-	15800	FOR BIS 25 % DISCOUNT
3.11(Acceptance Tests)	-	850	FOR BIS 25 % DISCOUNT
6(Composition)	-	16900	FOR BIS 25 % DISCOUNT
7(Dimensions of fitting)	-	500	FOR BIS 25 % DISCOUNT
8.2(Opacity)	-	700	FOR BIS 25 % DISCOUNT
8.1(Visual Appearance)	-	500	FOR BIS 25 % DISCOUNT
8.3(Stress Relief Test)	-	700	FOR BIS 25 % DISCOUNT
8.4(Vicat softening Temperature)	-	1100	FOR BIS 25 % DISCOUNT
8.5(Density)	-	700	FOR BIS 25 % DISCOUNT
8.6(Effect on water)	-	2000	FOR BIS 25 % DISCOUNT
9(Mechanical Properties)	-	127150	FOR BIS 25 % DISCOUNT
11(Marking)	-	500	FOR BIS 25 % DISCOUNT
Cl-6.2.2(Compound Chlorine Content)	-	16900	FOR BIS 25 % DISCOUNT
Cl-6.2.5(Verification of the Malfunction Temperature)	-	16000	FOR BIS 25 % DISCOUNT
Cl-9.1(Hydrostatic Characteristics)	-	16650	FOR BIS 25 % DISCOUNT
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	110500	FOR BIS 25 % DISCOUNT
3.1(Nominal Size(DN))	-	0	-
3.2(Nominal Outside Diameter)	-	0	-
3.3(Mean Inside Diameter of Socket at Entry)	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.5(Out-of-Roundness (Ovality))	-	0	-
3.6(Nominal Wall Thickness)	-	0	-
3.7(Minimum Wall Thickness)	-	0	-
3.8(Tolerance)	-	0	-
3.9(Working Pressure)	-	0	-
3.1(Standard Dimension Ratio)	-	0	-
3.11(Type Tests)	-	0	-
3.11(Acceptance Tests)	-	0	-
6(Composition)	-	0	-
7(Dimensions of fitting)	-	0	-
8.2(Opacity)	-	0	-
8.1(Visual Appearance)	-	0	-
8.3(Stress Relief Test)	-	0	-
8.4(Vicat softening Temperature)	-	0	-
8.5(Density)	-	0	-
8.6(Effect on water)	-	0	-
9(Mechanical Properties)	-	0	-
11(Marking)	-	0	-
Cl-6.2.2(Compound Chlorine Content)	-	0	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	0	-
Cl-9.1(Hydrostatic Characteristics)	-	0	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	0	-
3.1(Nominal Size(DN))	-	0	-
3.2(Nominal Outside Diameter)	-	0	-
3.3(Mean Inside Diameter of Socket at Entry)	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.5(Out-of-Roundness (Ovality))	-	0	-
3.6(Nominal Wall Thickness)	-	0	-
3.7(Minimum Wall Thickness)	-	0	-
3.8(Tolerance)	-	0	-
3.9(Working Pressure)	-	0	-
3.1(Standard Dimension Ratio)	-	0	-
3.11(Type Tests)	-	0	-
3.11(Acceptance Tests)	-	0	-
6(Composition)	-	0	-
7(Dimensions of fitting)	-	0	-
8.2(Opacity)	-	0	-
8.1(Visual Appearance)	-	0	-
8.3(Stress Relief Test)	-	0	-
8.4(Vicat softening Temperature)	-	0	-
8.5(Density)	-	0	-
8.6(Effect on water)	-	0	-
9(Mechanical Properties)	-	0	-
11(Marking)	-	0	-
Cl-6.2.2(Compound Chlorine Content)	-	0	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	0	-
Cl-9.1(Hydrostatic Characteristics)	-	0	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	0	-

23 Feb, 2027

-
Included.w.e.f.30.01.2025

IS 18482 (2023)

Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification

59960 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Sack Type)	-	500	FOR BIS 25 % DISCOUNT
5.2.1(Fabric)	-	500	FOR BIS 25 % DISCOUNT
5.2.2(Linear density of tapes)	-	500	FOR BIS 25 % DISCOUNT
5.2.4(Unlaminated fabric mass)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	500	FOR BIS 25 % DISCOUNT
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	500	FOR BIS 25 % DISCOUNT
5.4.1(Sack)	-	2000	FOR BIS 25 % DISCOUNT
5.4.1.1(Centre seam)	-	1000	FOR BIS 25 % DISCOUNT
5.4.1.2(Bottom seam)	-	1000	FOR BIS 25 % DISCOUNT
5.4.2(Sack)	-	1000	FOR BIS 25 % DISCOUNT
5.4.3(Sack)	-	500	FOR BIS 25 % DISCOUNT
5.4.5(Liner)	-	3000	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Inside length)	-	500	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Inside width)	-	500	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Gusset width)	-	500	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Warp per dm)	-	500	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Weft per dm)	-	500	FOR BIS 25 % DISCOUNT
6.1.1, Table 1(Mass of laminated fabric)	-	500	FOR BIS 25 % DISCOUNT
6.2, Table 1(Average breaking strength - Lengthwise)	-	1600	FOR BIS 25 % DISCOUNT
6.2, Table 1(Average breaking strength - Widthwise)	-	1600	FOR BIS 25 % DISCOUNT
6.2, Table 1(Breaking strength of bottom seam)	-	1600	FOR BIS 25 % DISCOUNT
6.2, Table 1(Breaking strength of centre seam)	-	1600	FOR BIS 25 % DISCOUNT
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	1600	FOR BIS 25 % DISCOUNT
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	1600	FOR BIS 25 % DISCOUNT
6.3(Average breaking strength - Lengthwise after UV exposure)	-	12800	FOR BIS 25 % DISCOUNT
6.3(Average breaking strength - Widthwise after UV exposure)	-	12800	FOR BIS 25 % DISCOUNT
6.4(Drop Impact Testing of Filled Sacks)	-	1100	FOR BIS 25 % DISCOUNT
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	500	FOR BIS 25 % DISCOUNT
Clause 6.2.2(Stitch strength)	-	1600	FOR BIS 25 % DISCOUNT
Clause 6.2.2(Weld seam strength)	-	1600	FOR BIS 25 % DISCOUNT
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	500	FOR BIS 25 % DISCOUNT
Clause 6.2.2(Stitch strength)	-	1600	FOR BIS 25 % DISCOUNT
Clause 6.2.2(Weld seam strength)	-	1600	FOR BIS 25 % DISCOUNT
Clause 6.5 Table 1 viii(Ash content)	-	1200	FOR BIS 25 % DISCOUNT

23 Feb, 2027

-
Included .w.e.f.29.11.2024

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

PE 63, PE 80 and PE 100

54875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1125	FOR BIS 25 % DISCOUNT
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	FOR BIS 25 % DISCOUNT
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	FOR BIS 25 % DISCOUNT
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	FOR BIS 25 % DISCOUNT
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	FOR BIS 25 % DISCOUNT
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	700	FOR BIS 25 % DISCOUNT
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	FOR BIS 25 % DISCOUNT
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	900	FOR BIS 25 % DISCOUNT
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	700	FOR BIS 25 % DISCOUNT
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	3000	FOR BIS 25 % DISCOUNT
5.2.1.1, T2(Compound ash content - Any Method)	-	1200	FOR BIS 25 % DISCOUNT
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	925	FOR BIS 25 % DISCOUNT
5.3(Density of Higher olefin - IS 7328:2020)	-	700	FOR BIS 25 % DISCOUNT
5.3(Olefin Constituents- 14333-2022)	-	2125	FOR BIS 25 % DISCOUNT
5.3(Loading of Carbon Black - IS 2530:1963)	-	925	FOR BIS 25 % DISCOUNT
5.3(Ash content- Any Method)	-	1200	FOR BIS 25 % DISCOUNT
5.3(Toluene extract - Any Method)	-	900	FOR BIS 25 % DISCOUNT
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	700	FOR BIS 25 % DISCOUNT
5.3(Carbon black particle size - Any Method)	-	3000	FOR BIS 25 % DISCOUNT
5.4(Antioxidant - Any Method)	-	0	FOR BIS 25 % DISCOUNT
6(Pipe Description - IS 14333-2022)	-	0	FOR BIS 25 % DISCOUNT
6.2(Colour- IS 14333-2022)	-	500	FOR BIS 25 % DISCOUNT
7.1(Visual Appearance- IS 14333-2022)	-	500	FOR BIS 25 % DISCOUNT
7.2(Length- IS 14333-2022)	-	500	FOR BIS 25 % DISCOUNT
7.3(Coiling- IS 14333-2022)	-	0	FOR BIS 25 % DISCOUNT
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	FOR BIS 25 % DISCOUNT
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	500	FOR BIS 25 % DISCOUNT
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	500	FOR BIS 25 % DISCOUNT
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	FOR BIS 25 % DISCOUNT
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	FOR BIS 25 % DISCOUNT
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	FOR BIS 25 % DISCOUNT
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	FOR BIS 25 % DISCOUNT
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	FOR BIS 25 % DISCOUNT
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	700	FOR BIS 25 % DISCOUNT
8.3(Carbon black content- IS 2530-1963)	-	925	FOR BIS 25 % DISCOUNT
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	FOR BIS 25 % DISCOUNT
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	FOR BIS 25 % DISCOUNT
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	FOR BIS 25 % DISCOUNT
8.6(Density-IS 7328:2020)	-	700	FOR BIS 25 % DISCOUNT
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1800	FOR BIS 25 % DISCOUNT
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1800	FOR BIS 25 % DISCOUNT
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1800	FOR BIS 25 % DISCOUNT
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	5500	FOR BIS 25 % DISCOUNT

23 Feb, 2027

-
Included.w.e.f.29.11.2024

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

Polyethylene/ Class 1 - 3 / Size - 12 -32mm

17725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	6900	25 % DISCOUNT FOR BIS
Cl-4.2(Carbon content of finished PE lateral pipe)	-	925	25 % DISCOUNT FOR BIS
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	25 % DISCOUNT FOR BIS
Cl-6.0(Visual Appearance)	-	500	25 % DISCOUNT FOR BIS
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	3000	25 % DISCOUNT FOR BIS
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1000	25 % DISCOUNT FOR BIS
Cl-7.2(Reversion Test)	-	1200	25 % DISCOUNT FOR BIS
Cl-7.3(Tensile Test)	-	1300	25 % DISCOUNT FOR BIS
Cl-7.3.1(Test Piece)	-	500	25 % DISCOUNT FOR BIS
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1200	25 % DISCOUNT FOR BIS
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	500	25 % DISCOUNT FOR BIS
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	500	25 % DISCOUNT FOR BIS
6(Visual Appearance)	-	500	25 % DISCOUNT FOR BIS
7.1 & Table 2(Hydraulic Characteristics)	-	1000	25 % DISCOUNT FOR BIS
7.1 & Table 2(Hydraulic Characteristics)	-	3000	25 % DISCOUNT FOR BIS
7.2(Reversion Test)	-	1200	25 % DISCOUNT FOR BIS
7.3(Tensile Strength)	-	1300	25 % DISCOUNT FOR BIS
7.3(Elongation at Break)	-	1300	25 % DISCOUNT FOR BIS
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	25 % DISCOUNT FOR BIS
4.2(a)(Carbon Black Content-IS 2530)	-	925	25 % DISCOUNT FOR BIS
4.2(b)(Carbon Black Dispersion-IS 2530)	-	925	25 % DISCOUNT FOR BIS
Cl-4.1(Material)	-	6900	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	925	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	3000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1000	-
Cl-7.2(Reversion Test)	-	700	-
Cl-7.3(Tensile Test)	-	1300	-
Cl-7.3.1(Test Piece)	-	500	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1200	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	500	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	500	-
6(Visual Appearance)	-	500	-
7.1 & Table 2(Hydraulic Characteristics)	-	3000	-
7.1 & Table 2(Hydraulic Characteristics)	-	1000	-
7.2(Reversion Test)	-	700	-
7.3(Tensile Strength)	-	1300	-
7.3(Elongation at Break)	-	1300	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	-
4.2(a)(Carbon Black Content-IS 2530)	-	925	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	700	-

23 Feb, 2027

-
Included w.e.f. 20.11.2024

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

High density polyethylene (HDPE) polypropylene (PP) wo

18580 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	250	-
5.2 Table 1(Dimensions)	-	250	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	-
5.2 Table 1(Ends per dm)	-	250	-
5.2 Table 1(Picks per dm)	-	250	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	2200	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100	-
5.2 Table 1(Drop impact strength)	-	1100	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	950	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 17216 (2019)

Polyethylene Mulch Films for Agriculture and Horticulture • Specification

Polyethylene Mulch Films for Agriculture

17950.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Density)	-	500	-
5.1.2(Melt Flow Index)	-	1100	-
5.1.4(Carbon black, Density)	-	925	-
5.1.4(Carbon black, Toluene extract)	-	925	-
5.1.4(Carbon black, Volatile matter)	-	925	-
5.1.4(Carbon black, particle size)	-	925	-
5.1.4(Carbon black, Tint strength)	-	925	-
5.2.1(Visual Appearance)	-	300	-
5.2.4(Odour)	-	250	-
5.3.1.1(Tolerance on thickness)	-	250	-
5.3.1.2(Tolerance on width)	-	250	-
5.3.2(Impact Strength)	-	1100	-
5.3.2, Table 1(Nominal Film Thickness)	-	250	-
5.3.2, Table 1(Impact Failure Mass)	-	1100	-
5.3.3(Tensile Strength at Break)	-	2200	-
5.3.4(Elongation at Break)	-	2200	-
5.3.5(Coefficient of Friction)	-	850	-
5.3.6(Elmendorf Tear Strength)	-	2200	-
5.3.7(Opacity)	-	575	-
5.4, Table 2(Carbon black, percent)	-	925	-
5.4, Table 2(Ash content, percent)	-	950	-
5.4, Table 2(Carbon black dispersion)	-	700	-
5.5(Service Life)	-	75860	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 16190 (2014)

Agro textiles - High density polyethylene (HDPE) laminated woven lay flat tube for irrigation purpose - Specification

HDPE laminated woven lay flat tube for irrigation

114531 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6. Table 2 v) IS 14714 (Abrasion resistance : Loss in breaking strength shall not be more than 15 percent)	-	875	-
6. Table 2 ix) a) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 15 percent Wrap)	-	1800	-
6. Table 2 ix) b) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 1 5 percent Weft)	-	1800	-
6. Table 2 iii) IS 1969 (Part 1) ( Elongation at break)	-	1100	-
6.5( Length : Unless specified otherwise, the standard length shall be 30 m. A tolerance of +5 percent shall be permitted on the length prescribed for the lay flat tube by the purchaser. No negative tolerance shall be permitted)	-	250	-
5,5.3 Table 1.(MANUFACTURE The laminated HDPE woven fabric is to be formed in to lay flat tube of the required inside diameter using a heat sealing process keeping the minimum overlap as specified in Table 1.)	-	250	-
6. Table 2 vi) a) IS 14293 ( Trapezoid tear strength: Wrap)	-	1100	-
6. Table 2 vi) b) IS 14293 ( Trapezoid tear strength : Weft)	-	1100	-
6. Table 2 i) IS 1964 (Mass)	-	250	-
6. Table 2 vii) Annex C (Puncture strength)	-	1100	-
6. Table 2 iv) b) Annex B(Retention of breaking strength after UV exposure of 500 h : weft 85 percent of original actual value (fabric))	-	1100	-
6. Table 2 ii) b) IS 1969 (Part 1) ( Breaking strength before UV exposure : Weft)	-	1100	-
6. Table 2 iv) a) Annex B(Retention of breaking strength after UV exposure of 500 h : Wrap 85 percent of original actual value (fabric))	-	1100	-
6. Table 2 ii) a) IS 1969 (Part 1) ( Breaking strength before UV exposure : Wrap)	-	1100	-
4,4.1 IS 6192( MATERIALS HDPE Tapes)	-	500	-
4.2 IS 6899(MATERIALS HDPE Fabric)	-	250	-
6. Table 2 viii) Annex D ( Environmental stress cracking test : )	-	1200	-
6. Table 2 x) Annex E (Cold cracking resistance test at –5°C)	-	1100	-
6.1 Table 1(Internal Diameter : The inside diameter of the lay flat tube shall be as given in Table 1. The internal diameter of the lay flat tube shall be measured by a suitable conical plug gauge and shall conform to the tolerance specified in Table 1)	-	250	-
6.2(Workmanship)	-	300	-
6.3,6.3.1(Hydrostatic Burst Pressure Test)	-	1000	-
6.4 , 6.4.1(Proof Pressure Tes)	-	1000	-
6.6(Kink Test :)	-	1100	-
6.7 IS 1969 (Part 1)(Welded Seam Strength Before UV Exposure : When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in IS 1969 (Part 1), welded seam strength before UV exposure shall be not less than the 80 percent of the original actual fabric strength)	-	1100	-
6.8 Annex B and IS 1969 (Part 1)(Welded Seam Strength After UV Exposure: When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in Annex B and IS 1969 (Part 1), the loss in welded seam strength after UV exposure shall be not more than 15 percent)	-	1100	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 17358 : Part 1 (2020)

Agro textiles “ Fencing nets for agriculture and horticulture purposes “ Specification Part 1 Fencing nets made from extruded polymer mesh

Fencing nets made from extruded polymer mesh

17948 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, table 1,2,3(MATERIALS)	-	5700	-
5.2(Colour)	-	250	-
(ii)(Mesh Size, Traverse Direction)	-	250	-
(iii)(Mesh Size, Cross Direction)	-	250	-
(vi)(Length)	-	250	-
(vi)(Width)	-	250	-
(vii) a(Tensile Strength before UV exposure, Machine Direction)	-	1100	-
(ix) a(Tensile Strength after UV exposure, Machine Direction)	-	1100	-
(vii) b(Tensile Strength before UV exposure, Traverse Direction)	-	1100	-
(ix) b(Tensile Strength after UV exposure, Traverse Direction)	-	1100	-
(viii) a(Elongation before UV exposure, Machine Direction)	-	1100	-
(viii) b(Elongation before UV exposure, Traverse Direction)	-	1100	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 16008 : Part 2 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 2 Shade nets made from mono filament yarns (first revision)

Shade nets made from mono filament yarns

17885 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Material)	-	1050	-
4.2(Fabric)	-	500	-
4.3(Colour)	-	300	-
5.0(Types)	-	1000	-
6.1(Dimensions and mass)	-	500	-
6.2 Table 1(Mass g/m2,Min)	-	250	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method,Warpway,Weftway 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min )	-	1100	-
6.2 Table 1(Warpway Weftway)	-	500	-
6.2 Table 1(Retention of breaking strength after UV exposure, N, Min)	-	1100	-
6.2 Table 1(Bursting pressure, kgf/cm2, Min)	-	1000	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 16008 : Part 1 (2016)

Agro textiles “ Shade nets for agriculture and horticulture purposes “ Specification Part 1 Shade nets made from tape yarns (first revision)

Shade nets made from tape yarns (first revision)

17885 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Types)	-	1000	-
6.1(Dimensions and Mass - IS 1954)	-	500	-
6.2 Table 1(Mass - IS 1964)	-	250	-
6.2 Table 1(Average breaking strength of shade nets fabric (Strip method, 325 mm x 50 mm test piece with gauge length of 200 mm) - IS 1969 (Part 1))	-	1100	-
6.2 Table 1(Retention of breaking strength after UV exposure - IS 1969 (Part 1))	-	1100	-
6.2 Table 1(Colour fastness to artificial light, IS 2454)	-	850	-
6.2 Table 1(Bursting Pressure, IS 1966 (Part 1 or 2))	-	1000	-
4.3, 4(Colour)	-	300	-
4.2, 4(Fabric )	-	500	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

Agro textiles “ Insect nets Fabric

20873 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	250	-
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	250	-
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	250	-
4.2( Netting Fabric)	-	500	-
4/4.1(b) percent on avarage value; and( MATERIAL / HDPE Monofilament Yarn)	-	2000	-
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	250	-
4.3( Colour)	-	300	-

23 Feb, 2027

-
Including w.e.f. 28.10.2024

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CIPET, Hyderabad

IDA Phase II, Cherlapally, Hyderabad, Medchal Malkajgiri, Telangana, 500051

9959333415 cipetptchyd@gmail.com

Scope List