BIS - LIMS (Laboratory Information Management System)

CIPET MYSURU

437/A, Hebbal indl. Area, Mysuru, Mysuru, Karnataka, 570016

8124489163 ptcmys@gmail.com

Scope List

Reset

20 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

15400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	225	Colour
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	825	K value
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	375	Dimensions
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Dimensions
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Dimensions
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Dimensions
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Dimensions
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	225	Visual Appearance
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	525	Stress Relief test
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	825	Reversion
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	8025	VST
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	Effect Of sunlight
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	Resistance to Sulphuric Acid
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1125	Res to External Blow
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	2450	Tensile Before & After Exposure
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	825	Axial Shrinkage
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	750	Water tightness of joints
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	750	Resistance to DCM
8.6(Effect on Water Test)	-	2250	EOW

Complete

31 Dec, 2026

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

6150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	225	Construction and workmanship
7.2(Flow path in emitters)	-	225	Flow path in the emitter
7.3.1(Resistance to Hydrostatic pressure)	-	750	Resistance to Hydrostatic pressure
7.3.2(Resistance to Hydrostatic pressure)	-	750	Resistance to Hydrostatic pressure
7.4.1(Emitter Pull Out In-line emitters)	-	750	Emitter Pull Out In-line emitters
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	750	Uniformity of Emission Rate Unregulated emitters
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	749.98	Uniformity of Emission Rate Regulated emitters
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	750	Emission rate as a function of inlet pressure Unregulated emitters
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	750	Emission rate as a function of inlet pressure Regulated emitters
8.3(Determination of Emitter Exponent)	-	450	Determination of Emitter Exponent

Complete

31 Dec, 2026

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

14532 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	1500	Polyethylene - Material
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	750.01	Toluene extract - Annex A of IS 12786:1989
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	525	Volatile matter - Annex B of IS 12786:1989
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	694	Carbon Black content - IS 2530: 1963
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	525	CBD
6.2.2(Fittings)	-	225	Visual
6.3(General)	-	225	Visual
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	750	Uniformity of Emission Rate for Unregulated Emitting Pipes
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	749.98	Uniformity of Emission Rate for Regulated Emitting Pipes
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	750	Emission Rate of Emitting Unit as a Function of Inlet Pressure
8.3.1(Wall Thickness ofEmitting Pipe)	-	188	Wall Thickness ofEmitting Pipe
8.3.2(Inside Diameter ofEmitting Pipe)	-	188	Inside Diameter ofEmitting Pipe
8.3.3(Flow Paths in Emitting Unit)	-	188	Flow Paths in Emitting Unit
8.3.4(Spacing ofEmitter Units)	-	300	Spacing ofEmitter Units
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	750	Resistance of Emitting Pipes to Hydrostatic Pressure
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	750	Resistance to Hydrostatic Pressure at Elevated Temperature
8.5(Resistance to Tension at Elevated Temperature)	-	1200	resistance to Tension at Elevated Temperature
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	300	Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479
8.7.1(Acceptance Test)	-	900	Acceptance Test
8.7.2(Type Test)	-	1200	Type Test
8.8(Determination of Emitting Unit Exponen)	-	450	Determination of Emitting Unit Exponenent
9.1(Non-regulated Emitting Pipe)	-	225	non-regulated Emitting Pipe
9.2(Regulated Emitting Pipe)	-	225.02	Regulated Emitting Pipe

Complete

31 Dec, 2026

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

up to 400mm

23656 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1050	Resistance to External Blows at 0°C
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	8250	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	375	Density
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	825	V S T
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	725	Reversion Test43
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	431.25	Opacity
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	225	VA
9.1(PIPE ENDS)	-	225	Pipe ends
8(SEALING RINGS)	-	0	Included
Clause 10.7(Sulphated Ash Content)	-	712.50	Sulphated Ash Content
7(DIMENSIONS-PIPE-Nominal Diameter)	-	375	All dim
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	Included
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	Included
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Included
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Included
7.2.1(DIMENSIONS-Socket)	-	5325	For EOW & Material
6(VCM CONTENT)	-	2250	VCM CONTENT
6(K- VALUE)	-	900	VCM CONTENT
10.3(Effect on Water)	-	2250	Effect on Water
10.1(Colour)	-	225	Colour
10.1(Surface Finish)	-	0	Surface Finish
7.2.1.1 Table3 (Angle of taper (Note-1))	-	0	Angle of taper (Note-1)
11.2(Resistance to External Blows at 0°C)	-	1000	Resistance to External Blows at 0°C
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	637.50	(Acceptance Test)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	637.50	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	525	Density
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	825	Vicat Softening Temperature
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	825	Reversion Test
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	Opacity
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	225	-Visual Appearance
9.1(PIPE ENDS)	-	0	PIPE ENDS
8(SEALING RINGS)	-	0	SEALING RINGS
10.7(Sulphated Ash Content)	-	900	Sulphated Ash Content
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	DIMENSIONS-PIPE- All
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	Mean O.D. (Minimum)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	DIMENSIONS-PIPE-O.D. at any Point (Minimum)
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	DIMENSIONS-PIPE-Ovality (Maximum)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	DIMENSIONS-PIPE-Thickness(Minimum)
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	DIMENSIONS-PIPE-Average Thickness
7.2.1(DIMENSIONS-Socket)	-	0	DIMENSIONS-Socket
6.1.1(VCM Content)	-	2250	VCM Content
6.1.2(PVC Resin)	-	825	K Value
10.3(Effect on Water Test)	-	2250	Effect on Water Test
10.1(Colour)	-	225	Colour
10.1(Surface Finish)	-	0	Surface Finish
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	Angle of taper (Note-1)

Complete

31 Dec, 2026

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

42290 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	8587.50	All test missed include raw material
6.1.3.1.1(Weldability Test)	-	638	All weldability
6.1.3.2 (Quick coupled fittings)	-	6312	Quick coupled male & female couplers & Sprinklers
6.1.2.2( Hydraulic Proof Test)	-	638	Pipe hydrostatics
6.1.1, 6.1.1.1(Leakage Test)	-	638	leakage test
4.1.5(Rubber Ring)	-	3750	All rubber ring test
Cl.4.1.3(Den sity Test)	-	1200	Density Test
4.1.3, Table 1,(ii)(Melt flow rate)	-	900	Melt flow rate
6.1(Thermal Stability (OIT))	-	1650	Thermal Stability (OIT)
4.1.1 (Table-1)(Volatile Matter)	-	900	Volatile Matter
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1975	tensile strenght at yield
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	0	Included
Cl.4.1.4(Carbon Black Content)	-	694	Carbon Black Content
4.1.4(The Carbon Content and Dispersion)	-	1219	Carbon Content and Dispersion
5(Dimensions of pipe - i) Outside diameter)	-	0	included
5(Dimensions of pipe - ii) Wall thickness minimum)	-	375	Dimensions of pipe - all dimensions
6(Visual Appearance)	-	225	Visual Appearance
7.1(Hydraulic Characteristics - Quality test)	-	3000	Hydraulic Characteristics - Quality test
7.1(Hydraulic Characteristics - Acceptance test)	-	1200	Hydraulic Characteristics - Acceptance test
Cl.7.1.3(Reversion Test)	-	825.01	Reversion Test
7.1.4(Tensile strength & elongation)	-	975	Tensile strength & elongation
Cl.7.1.5(Fusion Compatibility)	-	1200	Fusion Compatibility
Cl.7.1.6(Corrected Density)	-	1200	Corrected Density
Cl.7.1.7(MFR Test)	-	900	MFR Test
Cl.6.2.L(Wall Thickness)	-	0	Wall Thickness
Cl.6.2.4(Workmanship and Appearance)	-	225.01	Workmanship and Appearance
6.2.5(Holding attachment for coupler parts)	-	0	Holding attachment for coupler parts
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	375	Rubber Ring Hardness Shore – A (Before Ageing)
7.2.1(Leakage test 1hour / 27°C)	-	638	Leakage test 1hour
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	638.01	Hydraulic Proof test 1hour
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	1200	Acceptance Test (48 hrs)
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	3000	Type test
4.1.5(Carbon Black Specification)	-	3750	Density, Toluene ex, Volatile matt, ash content

Complete

31 Dec, 2026

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

10869 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	825	VST
9.5(Tensile Strength IS 12235(Part 13))	-	1325	Tensile Strength IS 12235(Part 13)
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1125	Resistance to External Blows at 0 ?C IS 12235 (Part 9)
9.3(Density IS 12235 (Part 14))	-	375	Density IS 12235 (Part 14)
9.2(Internal Diameter)	-	262.50	Internal Diameter
9.1( Visual Appearance)	-	225	Visual Appearance
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	187.5	Dimensions of sealing elements
8.4(Sealing rings - Hardness)	-	281.25	Sealing rings - Hardness
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	187.5	THREADING OF SCREEN ANDCASING PIPES. IS 554.
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	750	Effective length, l2
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	Wall thickness, Max included
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Wall thickness, Min included in dim
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0	Mean Outer Diameter over Connection included
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	Outer Diameter at any point included
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	0	DIMENSIONS - Casing Pipes included
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	5325	EOW, Raw material

Complete

31 Dec, 2026

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

upto 400mm diameter

38275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Polyethylene Resin)	-	1825	Polyethylene Resin MFI & DENSITY
5.3 (a)(Carbon Black Master Batch)	-	693.75	Carbon black content
5.3(b)(Carbon Black Master Batch)	-	525	Carbon black dispersion
5.3(c)(Carbon Black Master Batch)	-	1650	Thermal Stability (Oxidation Induction Time)
5.3(d)(Carbon Black Master Batch)	-	525	Volatile matter
5.3(e)(Carbon Black Master Batch)	-	525	Water content
8.3(Carbon black)	-	1219	CBC
8.6(Overall migration)	-	1575	Overall migration
6, 6.1(PIPE DESCRIPTION)	-	225	PIPE DESCRIPTION
6, 6.1.1(PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6, 6.1.2(PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6.1.3 (PIPE DESCRIPTION)	-	0	PIPE DESCRIPTION
6.1.4(PIPE DESCRIPTION)	-	0.01	PIPE DESCRIPTION
6.2(Colour)	-	225	Colour
6.2.1(6.1.1 Identification Stripes)	-	187.5	6.1.1 Identification Stripes
7.2(Length)	-	0	Length
7.4 table -3 & 4(6.1 Dimensions)	-	375	6.1 Dimensions
7.4.1.2(Ovality)	-	0	Ovality
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	16050	PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1200	Internal Pressure Creep Rupture Test of Pipe Joints
8.2(Longitudinal Reversion Test)	-	725	Reversion Test
8.4( Melt Flow Rate)	-	825	Melt Flow Rate
8.5 (Oxidation Induction Time)	-	1650	Oxidation Induction Time
8.7(Density)	-	1000	Density
8.8(Tensile Strength for Butt-fusion)	-	1325	Tensile Strength for Butt-fusion
8.9 table-6(Elongation at Break)	-	1325	Elongation at Break
8.10(Slow Crack Growth Rate)	-	4625	Slow Crack Growth Rate
5.2(Density)	-	525	Density
5.2(MFI @ 1900C/5.0 Kg)	-	825	MFI
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	1650	Oxidation Induction Time
5.2(Volatile matter Content)	-	525	Volatile matter Content
7.1(Visual Appearance)	-	225	VA
Cl 8.3(Carbon Black Content)	-	694	CBC
Clause 8.3(Carbon Black Dispersion)	-	525	CBD
Clause 8.6(Overall migration (stimulate))	-	1275	Overall Mig

Complete

31 Dec, 2026

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

HDPE woven sacks for packaging 50kg food grains

19117.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	187.50	Tapes – Width and Thickness ( IS 6192/IS 11197)
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	Tapes – Linear Density (IS 6192/IS 11197)
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	187.50	Tapes – Tenacity (IS 6192/IS 11197)
4.2 and Table 1 ii(Dimensions )	-	187.50	Dimension
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1500	Tapes – Dimensional stability (PP) (IS 11197) include identification
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12830	Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2650	Average breaking strength of fabric
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1325	Breaking strength of bottom seam
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Elongation at break of fabric
4.2 and Table 1 x(Ash content )	-	712.5	Ash content
4.2 and Table 1 v(Mass of sack )	-	225	Mass of sack
5.2 and Table 1 iii(Ends per dm )	-	187.5	Ends per dm
5.2 and Table 1 iv(Picks per dm )	-	187.5	Picks per dm
3.2(MFI)	-	825	MFI
3.1(Overall Migration)	-	1275	Overall Mig
3.1(Material Identification)	-	1500	Identification
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	825	Heat Shrinkage
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	0	Included in dimension
3.3.1(Bottom seam (IS 10789))	-	0	Included in dimension

Complete

31 Dec, 2026

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

Injection moulded PVC Socket fittings

4219 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	375	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	it will cover all dimension
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	it will cover all dimension
Cl. 6.1(Stress Relief Test- Appendix A)	-	525	for stress relief
Cl. 6.2(Opacity- Appendix B)	-	431.25	for opacity
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	2250	for complete effect on water
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	for complete effect on water
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	637.50	for short term test

Complete

31 Dec, 2026

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	Thickness
2.2.3(socket length)	-	0	Included In Thickness
2.1(General)	-	525	Stress relief test
2.1(General)	-	431.25	Opacity
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	Included In Thickness
2.2.3( inside diameter of the socket)	-	5962.75	Included In Thickness Effect on water Rs.2250/- & hydro pressure test Rs.637.50 for pipes VCM Content -Rs. 2250/- & K Value Rs. 825/- for raw material

Complete

31 Dec, 2026

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	375	For Dimensions Thickness & Socket length)
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	2250	For EOW Including all element detection
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	Included above
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	Included above
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	4668.75	EOW water charges included above, RS.1593 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For all Dimensions
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	Included in dimensions
2.2.3( inside diameter of the socket)	-	0	Included in dimensions
2.2.3(Socket length)	-	0	Included in dimensions
2.1(General)	-	0	Included in next
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	All DImensions
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	6918	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For All Dimensions
2.2.2, Table 1(Socket Laying Length)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	0	Added in below charges
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, Opacity Rs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	375	For All Dimensions
2.2.2, Table 1(Union Laying Length)	-	0	Included in above dimension charges
2.2.3( inside diameter of the socket)	-	0	Included in above dimension charges
2.2.3(Socket length)	-	0	Included in above dimension charges
2.1(General)	-	0	Added in below charges
2.1(General)	-	6918.75	RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2(diameter of the socket of cap)	-	375		For All Dimensions
2.1(General)	-	6918.75		RS.3843 is for addition of (Stress relief test Rs. 525, OpacityRs. 431.25, EOW. Rs.2250, &Short-term hydraulic test Rs. 637.50) Rs. 637.50 for socket fitting . And Rs. 3075 for raw material ( VCM Content Rs.2250 & K Value Rs. 825)

Complete

31 Dec, 2026

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

Diameter - 32 mm

13325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	1500	Potyethylene - higher olefins constituent
7.3(Tensile Test)	-	975	For tensile & Elongation
7.3(Elongation at Break)	-	0.00	included in tensile
7.4(SusceptibiIity to Environmental Stress Cracking)	-	900.00	E s c r
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0	For all dim
7.2(Reversion Test)	-	825.00	reversion Rs. 525 test & RS. 300 Specimen prep
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	375	Dimension charges
4.1.c.ii (Toluene extract - Annex A)	-	900	Toluene extract -
4.1.c.iii (Volatile matter - Annex B )	-	900	Volatile matter
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	694	CBC
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	525.03	The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	638	b) Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress
Cl. 7.1 Table -2(Quality Test for 100 hrs @ 70 c & 2.2 Mpa)	-	2250.01	Quality Test for 100 hrs @ 70 c & 2.2 Mpa
6(VISUAL APPEARANCE)	-	225	VISUAL APPEARANCE
4.1.c.i (Density)	-	1200	Density
4.1d(MATERIAL)	-	1500	MATERIAL

Complete

31 Dec, 2026

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Upto 20000 litres

17144 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	693.75	CBC
4.2.3(Carbon Dispersion Test)	-	525	CBD
5(Types and Features )	-	1200	CL. 4.1.1 density & MFI
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	2512.50	5.1,5.2,5.3&5.4 & 6.1
7.1.1(Resistance to Deformation)	-	525	Resistance to Deformation
7.2(Resistance to Impact)	-	825	Resistance to Impact
7.3(Test for Top Load Resistance)	-	675	Test for Top Load Resistance
7.4(Tensile Strength)	-	1325	Tensile Strength
7.5(Flexural Modulus)	-	1325	Flexural Modulus
7.6(overall Migration)	-	7537.50	Cl. 7.6, 9.1, 8.2 & Raw material

Complete

31 Dec, 2026

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

Diameter upto 400mm

39545 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Dimensions of pipes)	-	187.5	All Dim
7(Visual Appearance)	-	225	VA
4(Colour)	-	225.01	Color
8.1(Hydraulic characteristics)	-	4800	Hydraulic characteristics
8.2(Reversion)	-	825	Reversion
8.3(Density)	-	375	density
8.4(Melt Flow Rate)	-	825	MFI
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	694.02	cbc
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	525	CBD
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	375	Dimension all
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1200	Density
6.2(Colour- IS 14333-2022)	-	225	Colour
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	2250	100 hrs Pressure test
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1200	48 hrs pressure test
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	825	Reversion
8.6(Density-IS 7328:2020)	-	1200.01	Density
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	900	MFI
8.3(Carbon black content- IS 2530-1963)	-	694	CBC
8.3(Carbon black content Dispersion- IS 2530-1963)	-	525	CBD
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	Dimension
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	Dimension
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	900	MFI
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	1650	OIT
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	900	Volatile
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	525	Density
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	694.01	CBC
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	900	Toluene
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	900	Volatile matter
5.2.1.1, T2(Compound ash content - Any Method)	-	900	Ash
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	694	CBC
5.3(Density of Higher olefin - IS 7328:2020)	-	525	Density
5.3(Loading of Carbon Black - IS 2530:1963)	-	694	Carbon Black
5.3(Ash content- Any Method)	-	900	Ash Content
5.3(Toluene extract - Any Method)	-	825	Toluene
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	825	volatile matter
6(Pipe Description - IS 14333-2022)	-	225	Visual
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	2249.97	165 hrs.-Internal Pressure creep Rupture test,
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	8250	1000 hrs.-Internal Pressure creep Rupture test,
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1200	48 hrs.-Internal Pressure creep Rupture test,
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	1650.01	OIT
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	975	Butt Fusion tensile
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	975	Tensile
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	Included in tensile
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	1200	Slow Crack Growth Rate

Complete

31 Dec, 2026

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

Films

24106.25 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	225	Test charges after 25% BIS Discount from our actual Approved charges
5.1.2(Film Form)	-	0	Test charges included In Appearance
5.1.3(Odour)	-	0	Test charges included In Appearance
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	375	Test charges after 25% BIS Discount from our actual Approved charges
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	825	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6a(Carbon Black Content, Annex-A)	-	693.75	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6b(Ash Content, Annex-A)	-	600	Test charges after 25% BIS Discount from our actual Approved charges
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	525	Test charges after 25% BIS Discount from our actual Approved charges
5.2.2(Tolerance on Thickness, Annex-A)	-	187.50	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	525	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	Test charges included In Tensile properties
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	Test charges included In Tensile properties
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	637.50	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
6.1, Table 1(Tear resistence. B) Transverse direction )	-	825	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	525	Test charges after 25% BIS Discount from our actual Approved charges
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	Test charges included In Tensile properties
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	Test charges included In Tensile properties
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	637.50	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Tear resistance , Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
8.1, Table 3(Puncture resistance , Annex C)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Tear resistance , Annex B)	-	825	Test charges after 25% BIS Discount from our actual Approved charges
9.1, Table 4(Puncture resistance , Annex C)	-	1075	Test charges after 25% BIS Discount from our actual Approved charges

Complete

31 Dec, 2026

Bureau of Indian Standards

The National Standards Body of India

CIPET MYSURU

437/A, Hebbal indl. Area, Mysuru, Mysuru, Karnataka, 570016

8124489163 ptcmys@gmail.com

Scope List