BIS - LIMS (Laboratory Information Management System)

Urja Metallurgical Services LLP

J/P-15, Telco-Bhosari Road, Opp Sarayu Toyota Showroom, MIDC Bhosari, Pune (Bhosari), Pune, Maharashtra, 411026

9725213602 testing@UrjaMetlab.com

Scope List

Reset

7 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1364 : Part 2 (2023)

Hexagon head bolts screws and nuts of product grades A and B Part 2 Hexagon head screws (Size range M1.6 to M64 ) (Sixth revision of IS 1364 (Part 2))

All Grade / Type / Size / Designation / Class

10300 View breakup
-

Clause No.	Exclusion	Remark
Cl-4(Dimensions)	-	-
Cl-5, Table-5(General requirements)	-	-
Cl-5, Table-5(Thread-Tolerance class)	-	-
Cl-5, Table-5(Mechanical properties-Steel)	-	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	-
Cl-5, Table-5(Tolerances- Product grade)	-	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	-
Cl-6(Marking)	-	-

23 Dec, 2028

-
Included w.e.f 27.01.2026

IS 1364 : Part 1 (2023)

Hexagon head bolts, screws, and nuts of property grades A and B: Part 1 Hexagon head bolts (Size range M1.6 to M64) (sixth revision)

All Grade / Type / Size / Designation / Class

10300 View breakup
-

Clause No.	Exclusion	Remark
Cl-4(Dimensions)	-	-
Cl-5, Table-7(General requirements)	-	-
Cl-5, Table-7(Thread-Tolerance class)	-	-
Cl-5, Table-7(Mechanical properties- Steel)	-	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	-
Cl-5, Table-7(Tolerances-Product grade)	-	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	-
Cl-6(Marking)	-	-

23 Dec, 2028

-
Included w.e.f 27.01.2026

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

All Grade / Type / Size / Designation / Class

15500 View breakup
-

Clause No.	Exclusion	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	-
11(Transverse Tension Test,%)	-	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	-
14(Reverse Flattaning Test)	-	-
15(Flattaning Test-IS 2328)	-	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	-
18(Leak Tighteness Test)	-	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	-
20(Eddy current test, Air under water test ,Radiographic tests)	-	-
22(Workmanship, Finish and Appearance)	-	-
23(Repair by Welding or Grinding)	-	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	-
Clause 10.1 - Table 4(Tensile Strength)	-	-
Clause 10.1 - Table 4(Yield Strength)	-	-
Clause 10.1 - Table 4(Percent Elongation)	-	-
Clause 11(Transverse Tension Test)	-	-
Clause 12(Hardness Test)	-	-
Clause 13(Flange Test)	-	-
Clause 14(Reverse Flattening Test)	-	-
Clause 15(Flattening Test)	-	-
Clause 16(Grain Size)	-	-
Clause 18()	-	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	-
Clause 22(Workmanship, Finish & Appearance)	-	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	-
12.2(Hardness test)	-	-
17(Sampling)	-	-
25(Marking)	-	-
6.7, Table 7, ii)(c) Chromium VI)	-	-

23 Dec, 2028

-
Included w.e.f 27.01.2026 Exclusion: Cl 20 (Eddy current test, Air under water test ,Radiographic tests)

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

All Grade / Type / Size / Designation / Class

8500 View breakup
-

Clause No.	Exclusion	Remark
Clause - 7.1(CARBON)	-	-
Clause - 7.1(SULPHUR)	-	-
Clause - 7.1(PHOSPHURS)	-	-
Clause - 7.1(MANGANESE)	-	-
Clause - 7.1(NITROGEN)	-	-
As per Clause 10(Dimension)	-	-
As per Clause 10.1(Dimension Width)	-	-
As per Clause 10.1(Dimension Thickness)	-	-
As per Clause 10.2(Dimension Length)	-	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	-
As per Clause 11.5(Bend)	-	-
As per Clause 11.6(Camber)	-	-
As per Clause 11.7 (i)(Out of Square)	-	-
As per Clause 11.7 (ii)(Round Corners)	-	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	-
As per Clause 11.7 (ix)(Scarfing pits)	-	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	-
Clause. 13(Macro examination test.)	-	-
Clause. 13(Macro examination test.)	-	-
Clause. 13(Sulphur print.)	-	-
Clause. 13(Inclusion content)	-	-
Clause. 14(Marking)	-	-
Clause.15(Ordering information)	-	-
Clause.6.0(Manufacture)	-	-
Clause.7.1(Silicon)	-	-
Clause.7.1(Carbon Equbalant)	-	-
Clause.7.1(Microalloy element)	-	-

23 Dec, 2028

-
Included w.e.f 27.01.2026 Exclusion: Clause. 13 (Sulphur print.)

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

All Grade / Type / Size / Designation / Class

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	1500	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	1500	-
11(Transverse Tension Test,%)	-	1500	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1200	-
13 (Table No.- 7)(Flaring Test)	-	1000	-
14(Flattaning Test-IS 2328)	-	1000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	1500	-
17(Leak Tighteness Test)	-	1000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	1500	-
19(Eddy current test & Air under water)	-	500	-
21(Workmanship, Finish and Appearance)	-	500	-
22(Repair by Welding or Grinding)	-	500	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	1500	-
Clause 10.1 - Table 4(Tensile Strength)	-	1500	-
Clause 10.1 - Table 4(Percent Elongation)	-	1500	-
Clause 11(Transverse Tension Test)	-	1500	-
Clause 12(Hardness Test)	-	1200	-
Clause 13(Flaring Test)	-	1000	-
Clause 14(Flattening Test)	-	1000	-
Clause 15(Grain Size)	-	1500	-
Clause 17(Leak Tightness Test)	-	1000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	1500	-
Clause 21(Workmanship, Finish & Appearance)	-	500	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
10.2(Hardness test IS 1500 (part-1):2019)	-	1000	-
12.2(Flaring test IS 17878:2022)	-	1000	-
16(Sampling)	-	500	-
24(Marking)	-	100	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	500	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	500	-

23 Dec, 2028

-
Included w.e.f 27.01.2026 Exclusion: Cl 19 (Eddy current test & Air under water)

IS 1865 (1991)

Iron castings with spheroidal or nodular graphite - Specification (Third Revision)

9800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Grades)	-	2000	-
4.1(General requirements)	-	100	-
5(Manufacture)	-	100	-
6(Workmanship and finish)	-	100	-
7(Heat treatment)	-	100	-
9(Micro structure)	-	2000	-
10.1(Separately-Cast Test Samples)	-	1000	-
10.2(Cast-on Test Samples)	-	1000	-
11.1(Batch)	-	100	-
11.2(Number of Tests per Batch)	-	100	-
12.1(Tensile Strength)	-	2000	-
12.2(Impact Test)	-	2000	-
13.1(Tensile Test)	-	2000	-
13.2(Hardness Test)	-	2000	-
13.3(Impact Test)	-	2000	-
14(Validity of tests)	-	100	-
15(Retest)	-	3000	-
16(Additional test)	-	1000	-
17(Marking)	-	100	-

23 Dec, 2028

-
-

IS 210 (2009)

Grey iron castings - Specification (First Revision)

4900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	1000	-
13(SIZE OF TEST BARS-Length)	-	1000	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	2000	-
16, Table 3(Hardness Test)	-	2000	-
17,Annex B(TRANSVERSE TEST)	-	2000	-
18(HYDROSTATIC TEST)	-	2000	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	1000	-
13(SIZE OF TEST BARS-Length)	-	1000	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	2000	-
16, Table 3(Hardness Test)	-	2000	-
17,Annex B(TRANSVERSE TEST)	-	2000	-
18(HYDROSTATIC TEST)	-	1000	-
9(IS 7754)	-	2000	-
9(IS 7754)	-	2000	-
9(Microstructure)	-	2000	-
21(Marking)	-	100	-
9(Microstructure)	-	2000	-
7.2(Casting dimensions)	-	2000	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	2000	-

23 Dec, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Urja Metallurgical Services LLP

J/P-15, Telco-Bhosari Road, Opp Sarayu Toyota Showroom, MIDC Bhosari, Pune (Bhosari), Pune, Maharashtra, 411026

9725213602 testing@UrjaMetlab.com

Scope List