BIS - LIMS (Laboratory Information Management System)

(Suspended) Quality Marking & Testing Laboratory, Indore

03, Pologround, Industrial Estate, Indore (M.P.), Indore, Indore, Madhya Pradesh, 452015

9425601159 contactqmtl@yahoo.in

Scope List

Reset

39 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	560	For each test.
Cl 15(Length, Width & Thickness)	-	560	For each test.
Cl 12(Sudden Load Applied)	-	560	For each test.
Cl 11.3(Press)	-	560	For each test.
Cl 10.3(UTM)	-	560	For each test.
Cl 7(Workmanship)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	560	For each test.
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Camber)	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	560	For each test.
Cl. 15(Cl. 15 Channel Section: Depth)	-	560	For each test.
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	560	For each test.
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	560	For each test.
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	560	For each test.
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	560	For each test.
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	560	For each test.
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	560	For each test.
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	560	For each test.
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	560	For each test.
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	560	For each test.
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	560	For each test.
Cl 13(Y Groove Cracking Test)	-	560	For each test.

31 Jul, 2024

-
-

IS 13801 (2013)

Chequered Cement Concrete Tiles -

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	390	For each parameter.
Cl 12.1(Concavity & Convexity )	-	560	For each test
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	560	For each test
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	560	For each test
Cl 12.4(Water absorption)	-	690	For each test
Cl 12.5(Wet transverse strength)	-	1410	For each test
Cl 12.6(Resistance to wear)	-	1410	For each test
Cl 11(Finish)	-	560	For each test
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	390	For each test
Cl 12.1(Concavity & Convexity )	-	560	For each test
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	560	For each test
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	560	For each test
Cl 12.4(Water absorption)	-	690	For each test
Cl 12.5(Wet transverse strength)	-	1410	For each test
Cl 12.6(Resistance to wear)	-	1410	For each test
Cl 11(Finish)	-	560	For each test

31 Jul, 2024

-
-

IS 1363 : Part 1 (2019)

Hexagon Head Bolts, Screws and Nuts of Product Grade ‘C’ Part 1 Hexagon Head Bolts ( Size Range M 5 to M 64 ) ( Fifth Revision )

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-d)	-	560	For each test
3-Table 1(Dimensions-p)	-	560	For each test
3-Table 1(Dimensions-b)	-	560	For each test
3-Table 1(Dimensions-c(Maximum))	-	560	For each test
3-Table 1(Dimensions-da(Maximum))	-	560	For each test
3-Table 1(Dimensions-ds(Minimum))	-	560	For each test
3-Table 1(Dimensions-dw(minimum))	-	560	For each test
3-Table 1(Dimensions-e(minimum))	-	560	For each test
3-Table 1(Dimensions-k(nominal))	-	560	For each test
3-Table 1(Dimensions-ds(maximum))	-	560	For each test
3-Table 1(Dimensions-k(Minimum))	-	560	For each test
3-Table 2(Dimensions-k(maximum))	-	560	For each test
3-Table 1(Dimensions-kw(minimum))	-	560	For each test
3-Table 1(Dimensions-r(minimum))	-	560	For each test
3-Table 1(Dimensions-s(minimum))	-	560	For each test
3-Table 1(Dimensions-s(maximum))	-	560	For each test
3-Table 2(Dimensions-l(nominal))	-	560	For each test
3-Table 2(Dimensions-l(minimum))	-	560	For each test
3-Table 2(Dimensions-l(maximum))	-	560	For each test
3-Table 1(Dimensions-ls(minimum))	-	560	For each test
3-Table 1(Dimensions-lg(maximum))	-	560	For each test
3-Table 1(Dimensions-β)	-	560	For each test
3-Table 2(Dimensions-u)	-	560	For each test
4-Table 3(General requirements-ISO 8992)	-	560	For each test
4-Table 3(Threads-ISO 724 & 965(1))	-	560	For each test
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	1980	For each test
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	390	For each test
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	690	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screw (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Raw material seams and laps (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	560	For each test

31 Jul, 2024

-
Except size 22mm dia

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

364000 View breakup
Testing Charges: For complete test as per Indian Standard (IS 15500(Pt.1to8)): For SDWP as per IS 15500(Pt.1 & Pt.2): Rs 1,00,800/-; For EDWP as per IS 15500(Pt.1 & Pt.2): Rs. 99,360/-; For VLOM-50 as per IS 15500(Pt.1 & Pt.2): Rs. 78, 000/-;For VLOM-65 as per IS 15500(Pt.1 & Pt.2): 85,000/- For tests as per IS 15500(Pt.3): For SDWP, EDWP,VLOM-50,VLOM-65 as per IS 15500(Pt.3) : Rs. 8000/- for each type Testing charges for individual components : For SDWP, EDWP,VLOM-50,VLOM-65 as per IS 15500(Pt.1,2,4,5,6 & 7): Rs. 2000/- for each components

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1)(Raw material)	-	2000	-
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1)(Raw material)	-	2000	-
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1)(Raw material)	-	2000	-
2/2.3,(Refer 15500(Part 1 to 8)& 9.4 (Part 1)(Dimensions & critical dimensions in conformance with the relevant figures in Part 4.)	-	560	For each component test
2/2.3,(Refer fig 4.1 of Part4) & 9.4 (Part 1)(Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.2 of Part4)(Dimensions of FIG. 4,2 HEAD— EWDP)	-	560	For each component test
2/2.3,(Refer fig 4.3A of Part4)(Dimensions of Fig 4.3A Side Plate)	-	560	For each component test
2/2.3,(Refer fig 4.3B of Part4)(Dimensions of Fig 4.3B Head Flange)	-	560	For each component test
2/2.3,(Refer fig 4.3C of Part4)(Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.3D of Part4)(Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.3E of Part4)(Dimensions of Fig 4.3E Back Plate — EDWP)	-	560	For each component test
2/2.3,(Refer fig 4.3F of Part4)(Dimensions of Fig 4.3F Bracket — EDWP)	-	560	For each component test
2/2.3,(Refer fig 4.3G of Part4)(Dimensions of Fig 4.3G Axle Bust — Right)	-	560	For each component test
2/2.3,(Refer fig 4.3H of Part4)(Dimensions of Fig 4.3H Axle Bust — Left)	-	560	For each component test
2/2.3,(Refer fig 4.3I of Part4)(Dimensions of Fig 4.3 I Front Top End Plate)	-	560	For each component test
2/2.3,(Refer fig 4.3IJof Part4)(Dimensions of 4.3J Front Bottom End Plate)	-	560	For each component test
2/2.3,(Refer fig 4.3IKof Part4)(Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.3L Jof Part4)(Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-	560	For each component test
2/2.3,(Refer fig 4.4 Jof Part4)(Dimensions of FIG. 4.4 FRONTCOVER)	-	560	For each component test
2/2.3,(Refer fig 4.5A of Part4)(Dimensions of FIG. 4.5A Flange for Third Plate)	-	560	For each component test
2/2.3,(Refer fig 4.5 B of Part4)(Dimensions of FIG. 4.5B Guide Bush )	-	560	For each component test
2/2.3,(Refer fig 4.6 of Part4)(Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.7 of Part4)(Dimensions of FIG.4.7 HANDLE— EDWP)	-	560	For each component test
2/2.3,(Refer fig 4.8A of Part4)(Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.8B of Part4)(Dimensions of FIG 4.8B Handle Bar — EDWP)	-	560	For each component test
2/2.3,(Refer fig 4.8C of Part4)(Dimensions of FIG 4.8C Chain Guide)	-	560	For each component test
2/2.3,(Refer fig 4.8 D of Part4)(Dimensions of Fig 4.8D Bearing Housing )	-	560	For each component test
2/2.3,(Refer fig 4.9 of Part4)(Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-	560	For each component test
2/2.3,(Refer fig 4.10 of Part4)(Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-	560	For each component test
2/2.3,(Refer fig 4.11 of Part4)(Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-	560	For each component test
2/2.3,(Refer fig 4.12A of Part4)(Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.12B of Part4)(Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.13A of Part4)(Dimensions of Fig 4.1 3A Telescopic Stand — EDWP (For borewell with 150 NB casing pipe) FOR EDWP )	-	560	For each component test
2/2.3,(Refer fig 4.13B of Part4)(Dimensions of Fig 4.1 3B Normal Stand — EDWP (For borewell with 100/125 NB casing pipe) FOR EDWP )	-	560	For each component test
2/2.3,(Refer fig 4.14 A of Part4)(Dimensions of Fig 4.1 4A Stand Pipe — Standard (For SDWP, VLOM-65, VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 4.14 B of Part4)(Dimensions of Fig 4.14B Stand Pipe — EDWP (For EDWP))	-	560	For each component test
2/2.3,(Refer fig 4.14 C of Part4)(Dimensions of Fig 4.14C Stand Flange)	-	560	For each component test
2/2.3,(Refer fig 4.14 D of Part4)(Dimensions of Fig 4.14D Leg)	-	560	For each component test
2/2.3,(Refer fig 4.14 E of Part4)(Dimensions of Fig 4.14E Gusset)	-	560	For each component test
2/2.3,(Refer fig 4.14 F of Part4)(Dimensions of Fig 4.1 4F Reducer Coller)	-	560	For each component test
2/2.3,(Refer fig 4.14 G of Part4)(Dimensions of Fig 4.14G Spike)	-	560	For each component test
2/2.3,(Refer fig 4.15 of Part4)(Dimensions of FIG, 4.15 WATER TANK — 32 (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 4.16 of Part4)(Dimensions of FIG. 4.16 WATERTANK— 50)	-	560	For each component test
2/2.3,(Refer fig 4.17 of Part4)(Dimensions of FIG. 4.17 WATERTANK— 65)	-	560	For each component test
2/2.3,(Refer fig 4.18A of Part4)(Dimensions of FIG. 4.1 8A Tank Pipe )	-	560	For each component test
2/2.3,(Refer fig 4.18B of Part4)(Dimensions of FIG. 4.18B Tank Top Flange)	-	560	For each component test
2/2.3,(Refer fig 4.18C of Part4)(Dimensions of FIG. 4.18C Spout)	-	560	For each component test
2/2.3,(Refer fig 4.18D of Part4)(Dimensions of FIG 4.1 8D Gusset)	-	560	For each component test
2/2.3,(Refer fig 4.18E of Part4)(Dimensions of FIG 4.18E Tank Bottom Flanae — 32 (For SWDP & EDW~))	-	560	For each component test
2/2.3,(Refer fig 4.18F of Part4)(Dimensions of FIG 4.1 8F Riser Pipe Holder — 32 (For SWDP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 4.18G of Part4)(Dimensions of FIG 4. 18G Riser Pipe Holder — 50)	-	560	For each component test
2/2.3,(Refer fig 4.18H of Part4)(Dimensions of FIG 4.1 8H Tank Bottom Flange — 50)	-	560	For each component test
2/2.3,(Refer fig 4.18I of Part4)(Dimensions of FIG 4.18I Tank Bottom Flange — 65 )	-	560	For each component test
2/2.3,(Refer fig 4.18J of Part4)(Dimensions of FIG 4.18J Riser Pipe Holder — 65 )	-	560	For each component test
2/2.3,(Refer fig 4.19 of Part4)(Dimensions of FIGFIG. 4.19 CONE PLATE)	-	560	For each component test
2/2.3,(Refer fig 4.20 A of Part4)(Dimensions of FIG 4.20A Cone Flange)	-	560	For each component test
2/2.3,(Refer fig 4.20 B of Part4)(Dimensions of FIG 4.20B Steel Cone)	-	560	For each component test
2/2.3,(Refer fig 4.21 of Part4)(Dimensions of FIG. 4.21 CONNECTING ROD)	-	560	For each component test
2/2.3,(Refer fig 4.22of Part4)(Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-	560	For each component test
2/2.3,(Refer fig 4.23of Part4)(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	560	For each component test
2/2.3,(Refer fig 4.24of Part4)(Dimensions of FIG. 4.24 HANDLEAXE )	-	560	For each component test
2/2.3,(Refer fig 4.25 of Part4)(Dimensions of FIG. 4.25 PUSHROD )	-	560	For each component test
2/2.3,(Refer fig 4.26 of Part4)(Dimensions of FIG. 4.26 BEARINGSPACER)	-	560	For each component test
2/2.3,(Refer fig 4.27 of Part4)(Dimensions of FIG.4.27 WASHER)	-	560	For each component test
2/2.3,(Refer fig 4.28 of Part4)(Dimensions of FIG. 4.28 SOCKET— 32 (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 4.30 of Part4)(Dimensions ofFIG. 4.30 SOCKET— 65 (For VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 5.1 of Part 5)(Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-	560	For each component test
2/2.3,(Refer fig 5.2 of Part 5)(Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 5.3 of Part 5)(Dimensions of FIG. 5.3 CYLINDERBODY— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 5.4 of Part 5)(Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-	560	For each component test
2/2.3,(Refer fig 5.5A of Part 5)(Dimensions of FIG. 5.5 A CYLINDERCAPS— VLOM-65 (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 5.5B of Part 5)(Dimensions of FIG. 5.5 BCYLINDERCAPS— V LOM-65 (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 5.6 of Part 5)(Dimensions ofFIG. 5.6 CYLINDERCAPS— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 6.1 of Part 6)(Dimensions of FIG. 6.1 A BRASS LINER)	-	560	For each component test
2/2.3,(Refer fig 6.1 of Part 6)(Dimensions of FIG. 6.1 B BRASS LINER)	-	560	For each component test
2/2.3,(Refer fig 6.1 of Part 6)(Dimensions of FIG. 6.1 C BRASS LINER)	-	560	For each component test
2/2.3,(Refer fig 6.2 of Part 6)(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 6.3 of Part 6)(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 6.4 of Part 6)(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 6.5 of Part 6)(Dimensions of FIG.6.5 BUCKET SPACER — LOWER (For EDWP))	-	560	For each component test
2/2.3,(Refer fig 6.6 of Part 6)(Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-	560	For each component test
2/2.3,(Refer fig 6.7 of Part 6)(Dimensions of FIG. 6.7 FOLLOWER— EDWP)	-	560	For each component test
2/2.3,(Refer fig 6.8 of Part 6)(Dimensions of FIG. 6.8 FOLLOWER— VLOM-65)	-	560	For each component test
2/2.3,(Refer fig 6.9 of Part 6)(Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-	560	For each component test
2/2.3,(Refer fig 6.10 of Part 6)(Dimensions of FIG. 6.10 CHECKVALVE— VLOM-65)	-	560	For each component test
2/2.3,(Refer fig 6.11 of Part 6)(Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 6.12 of Part 6)(Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 6.13 of Part 6)(Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-	560	For each component test
2/2.3,(Refer fig 6.14 of Part 6)(Dimensions of FIG. 6.14 CAGE (For VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 6.15 of Part 6)(Dimensions of FIG. 6.15 PLUNGERVALVE BODY— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 6.16 of Part 6)(Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 7.1 of Part 7)(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	560	For each component test
2/2.3,(Refer fig 7.2 of Part 7)(Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 7.3 of Part 7)(Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-	560	For each component test
2/2.3,(Refer fig 7.4 of Part 7)(Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-	560	For each component test
2/2.3,(Refer fig 7.5 of Part 7)(Dimensions of FIG. 7.5 SEALINGRING— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 7.6 of Part 7)(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3,(Refer fig 7.7 of Part 7)(Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-	560	For each component test
2/2.3,(Refer fig 7.8 of Part 7)(Dimensions of FIG. 7.8 LOWERVALVE SEATING— VLOM-65 68)	-	560	For each component test
2/2.3,(Refer fig 7.9 of Part 7)(Dimensions ofFIG. 7.9 BOBBIN (For VLOM-50))	-	560	For each component test
2/2.3,(Refer fig 7.10 of Part 7)(Dimensions of FIG. 7.10 O-RING— VLOM-65)	-	560	For each component test
2/2.3,(Refer fig 7.11 of Part 7)(Dimensions of FIG. 7.11 O-RING—VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 7.12 of Part 7)(Dimensions of FIG. 7.12 RUBBER CONE— VLOM-65 )	-	560	For each component test
2/2.3,(Refer fig 7.13 of Part 7)(Dimensions of FIG. 7.13 RUBBERCONE— VLOM-50)	-	560	For each component test
2/2.3,(Refer fig 7.14 of Part 7)(Dimensions of FIG. 7.14 PIPE CENTRALIZER— VLOM-65 )	-	560	For each component test
2/2.3,(Refer fig 7.15 of Part 7)(Dimensions of FIG.7.15 PIPECENTRALIZER— VLOM-50 )	-	560	For each component test
2/2.3,(Refer fig 7.15 of Part 7)(Dimensions of FIG.7.15 PIPECENTRALIZER— VLOM-50 )	-	560	For each component test
3/3.3.1,(Refer Cl 9.4.1 and 9.4.3 15500(Part 1 )(Head and Cylinder Assemblies)	-	4000	Each clause wise test 200
3/3.3.2,(Refer 15500(Part 4 and 7 )(Other Components)	-	2000	2000 is applicable for each component.
6.1 of Part 1 ,refer Condition 4 of IS 1573(Electro-galvanizing )	-	560	For each component test
6.2 of Part 1 ,Refer IS 4759(Galvanizing)	-	1680	For each component test
6.2.1 of Part 1,Refer Cl 5.9 of IS 2629(Galvanizing)	-	1680	For each component test
6.3.1 of Part1, refer IS 2074 And 2932( Painting)	-	560	For each component test
6.3.1 of Part1, refer IS 2074 And 2932( Painting)	-	560	For each component test
6.3.2 of Part1, ( Painting)	-	560	For each component test
6.3.3of Part1, ( Painting)	-	560	For each component test
9.2 of Part1, (Visual Tests)	-	560	For each component test
9.4/9.4.1.1 of part 1(Dimensional and Other Tests/head assembly )	-	560	For each component test
9.4/9.4.1 .2 of part 1(Head assembly )	-	2000	For each component test
9.4/9.4.1 .2 of part 1(handle shall be checked for lateral play at the end of the square section of handle on either side)	-	560	For each component test
9.4/9.4.1.2 of part 1(The clearance between the handle and the bracket )	-	560	For each component test
9.4/9.4.1 .2 of part 1(The stroke of the pump )	-	560	For each component test
9.4/9.4.2.1 of part 1(Handle Assembly)	-	560	For each component test
9.4/9.4.2.1 of part 1(Handle Assembly)	-	560	For each component test
9.4/9.4.3of part 1(Cylinder Assembly )	-	2000	For each component test
9.4/9.4.3of part 1(Cylinder Assembly )	-	2000	For each component test
9.4/9.4.3of part 1(Cylinder Assembly )	-	2000	For each component test
9.4/9.4.3of part 1 refer table 3(Discharge of Pump)	-	2000	For each component test
9.4/9.4.4of part 1(Valve Assemblies)	-	560	For each component test
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1)(Raw mateerial)	-	2810	For each component test
2/2.3,(Refer 15500(Part 1 to 8)& 9.4 (Part 1)(Dimensions & critical dimensions in conformance with the relevant figures in Part 4.)	-	560	For each component test
2/2.3 ,Refer Fig 3.1(Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-	560	For each component test
2/2.3 ,Refer Fig 3.1(Dimensions of FIG. 4.4 FRONT COVER)	-	560	For each component test
2/2.3 ,Refer Fig 3.1(Dimensions of FIG. 4.24 HANDLE AXE )	-	560	For each component test
2/2.3 ,Refer Fig 3.1(Dimensions of FIG.4.27 WASHER)	-	560	For each component test
2/2.3 ,Refer Fig 3.1 and Refer annex B( HexagonaI Nut — )	-	2000	For each component test
2/2.3 ,Refer Fig 3.1 and Refer annex B(Hexagonal Bolt)	-	2000	For each component test
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-	560	For each component test
2/2.3 ,Refer Fig 3.1 and 3.2(Dimensions of FIG. 4.26 BEARING SPACER)	-	560	For each component test
2/2.3 ,Refer Fig 3.1 and 3.2,Annex B(Prevailing Torque Type Hex. Nut)	-	2000	For each component test
2/2.3 ,Refer Fig 3.1 and 3.2,Annex B(Hex. Bolt)	-	2000	For each component test
2/2.3 ,Refer Fig 3.3(Dimensions of FIG. 4,2 HEAD— EWDP)	-	560	For each component test
2/2.3 ,Refer Fig 3.3(Dimensions of FIG. 4.4 FRONT COVER)	-	560	For each component test
2/2.3 ,Refer Fig 3.3(Dimensions of FIG. 4.24 HANDLE AXE )	-	560	For each component test
2/2.3 ,Refer Fig 3.3(Dimensions of FIG.4.27 WASHER)	-	560	For each component test
2/2.3 ,Refer Fig 3.3 and annex B(Hexagonal Nut—)	-	2000	For each component test
2/2.3 ,Refer Fig 3.3 and annex B(Hexagonal Bolt)	-	2000	For each component test
2/2.3 ,Refer Fig 3.3 and 3.4(Ball bearing, single side shielded)	-	2000	For each component test
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-	560	For each component test
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 6.1 BRASS LINER)	-	560	For each component test
2/2.3 ,Refer Fig 3.5(Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.5 and 3.6(Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.5 A Upper CAPS— VLOM-65 (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 5.5 B Bottomr CAPS— VLOM-65 (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 6.1 B BRASS LINER)	-	560	For each component test
2/2.3 ,Refer Fig 3.7(Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.8 FOLLOWER— VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.10 CHECKVALVE— VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 6.14 CAGE (For VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.8 LOWERVALVE SEATING— VLOM-65 68)	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Dimensions of FIG. 7.10 O-RING— VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.7 and 3.8(Check Nut)	-	2000	For each component test
2/2.3 ,Refer Fig 3.9(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	560	For each component test
2/2.3 ,Refer Fig 3.9(Dimensions of FIG. 5.3 CYLINDERBODY— VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9(Dimensions ofFIG. 5.6 CYLINDERCAPS— VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9(Dimensions of FIG. 6.1 C BRASS LINER)	-	560	For each component test
2/2.3 ,Refer Fig 3.9(Dimensions of FIG. 7.5 SEALINGRING— VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 6.15 PLUNGERVALVE BODY— VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 7.9 BOBBIN)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Dimensions of FIG. 7.11 O-Ring — VLOM-50)	-	560	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Hexagonal Nut)	-	2000	For each component test
2/2.3 ,Refer Fig 3.9 and 3.10(Hexagonal Bolt)	-	2000	For each component test
2/2.3 ,Refer Fig 3.11(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	560	For each component test
2/2.3 ,Refer Fig 3.11(Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.11(Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-	560	For each component test
2/2.3 ,Refer Fig 3.11(Dimensions of FIG. 6.1 B BRASS LINER)	-	560	For each component test
2/2.3 ,Refer Fig 3.11(Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG.6.5 BUCKET SPACER — LOWER (For EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.7 FOLLOWER— EDWP)	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-	560	For each component test
2/2.3 ,Refer Fig 3.11 and 3.12(Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-	560	For each component test
3.3.3, Refer 9.4.3 of Part 1(Cylinder Assembly )	-	2000	For each component test
3.3.3, Refer 9.4.3 of Part 1(Cylinder Assembly )	-	2000	For each component test
3.3.3, Refer 9.4.3 of Part 1(Cylinder Assembly )	-	2000	For each component test
3.3.3, Refer 9.4.3 of Part 1(Discharge of Pump)	-	2000	For each component test
3.3.4,Refer 9.4.4 of Part 1(Valve Assemblies)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4,2 HEAD— EWDP)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3A Side Plate)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3B Head Flange)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3E Back Plate — EDWP)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3F Bracket — EDWP)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3G Axle Bust — Right)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3H Axle Bust — Left)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3 I Front Top End Plate)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of 4.3J Front Bottom End Plate)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.4 FRONTCOVER)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.5A Flange for Third Plate)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.5B Guide Bush )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG.4.7 HANDLE— EDWP)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.8B Handle Bar — EDWP)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.8C Chain Guide)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.8D Bearing Housing )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.1 3A Telescopic Stand — EDWP (For borewell with 150 NB casing pipe) FOR EDWP )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.1 3B Normal Stand — EDWP (For borewell with 100/125 NB casing pipe) FOR EDWP )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.1 4A Stand Pipe — Standard (For SDWP, VLOM-65, VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.14B Stand Pipe — EDWP (For EDWP))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.14C Stand Flange)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.14D Leg)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.14E Gusset)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.1 4F Reducer Coller)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of Fig 4.14G Spike)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG, 4.15 WATER TANK — 32 (For SDWP & EDWP))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.16 WATERTANK— 50)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.17 WATERTANK— 65)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.1 8A Tank Pipe )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.18B Tank Top Flange)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.18C Spout)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.1 8D Gusset)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.18E Tank Bottom Flanae — 32 (For SWDP & EDW~))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.1 8F Riser Pipe Holder — 32 (For SWDP & EDWP))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4. 18G Riser Pipe Holder — 50)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.1 8H Tank Bottom Flange — 50)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.18I Tank Bottom Flange — 65 )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.18J Riser Pipe Holder — 65 )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIGFIG. 4.19 CONE PLATE)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.20A Cone Flange)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG 4.20B Steel Cone)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.21 CONNECTING ROD)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.24 HANDLEAXE )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.25 PUSHROD )	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.26 BEARINGSPACER)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG.4.27 WASHER)	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.28 SOCKET— 32 (For SDWP & EDWP))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions of FIG. 4.29 SOCKET— 50 (For VLOM-50))	-	560	For each component test
2.2 , Refer 4.1 of Part 1(Dimensions ofFIG. 4.30 SOCKET— 65 (For VLOM-65))	-	560	For each component test
2.2(Raw Material- as per Cl 5 of Part 1)	-	2000	For each component test
2.2(Raw Material- as per Cl 5 of Part 1)	-	2000	For each component test
2.2, fig 5.1(Dimensions)	-	560	For each component test
2.2, fig 5.2(Dimensions)	-	560	For each component test
2.2, fig 5.3(Dimensions)	-	560	For each component test
2.2, fig 5.4(Dimensions)	-	560	For each component test
2.2, fig 5.5(Dimensions)	-	560	For each component test
2.2, fig 5.6(Dimensions)	-	560	For each component test
2.3(Anti corrosive treatment - Electro-galvanizing, Galvanizing, Painting- as per Cl 6 of Part 1)	-	2000	Anti corrosive treatment - 560 , Electro-galvanizing- 560 , Galvanizing - 1680 .
2.2(Raw Material- as per Cl 5 of Part 1)	-	2000	For each component test
2.2(Raw Material- as per Cl 5 of Part 1)	-	2000	For each component test
2.2, fig 7.1(Dimensions)	-	560	For each component test
2.2, fig 7.2(Dimensions)	-	560	For each component test
2.2, fig 7.3(Dimensions)	-	560	For each component test
2.2, fig 7.4(Dimensions)	-	560	For each component test
2.2, fig 7.5(Dimensions)	-	560	For each component test
2.2, fig 7.6(Dimensions)	-	560	For each component test
2.2, fig 7.7(Dimensions)	-	560	For each component test
2.2, fig 7.8(Dimensions)	-	560	For each component test
2.2, fig 7.9(Dimensions)	-	560	For each component test
2.2, fig 7.10(Dimensions)	-	560	For each component test
2.2, fig 7.11(Dimensions)	-	560	For each component test
2.2, fig 7.12(Dimensions)	-	560	For each component test
2.2, fig 7.13(Dimensions)	-	560	For each component test
2.2, fig 7.14(Dimensions)	-	560	For each component test
2.2, fig 7.15(Dimensions)	-	560	For each component test
3.3, Fig. 6.1A(Critical Dimensions - Brass Liner-Short (For SDWP))	-	560	For each component test
3.3, Fig. 6.1B(Critical Dimensions - Brass Liner-Long (For EDWP & VLOM-65))	-	560	For each component test
3.3, Fig. 6.1C(Critical Dimensions - Brass Liner-VLOM-50 (For VLOM-50 ))	-	560	For each component test
3.3, Fig. 6.2(Critical Dimensions - Plunger Yoke Body (For SDWP, EDWP & VLOM-65))	-	560	For each component test
3.3, Fig. 6.3(Critical Dimensions - Upper Valve (For SDWP, EDWP & VLOM-65))	-	560	For each component test
3.3, Fig. 6.4(Critical Dimensions - Bucket Spacer-Standard (For SDWP, EDWP & VLOM-65))	-	560	For each component test
3.3, Fig. 6.5(Critical Dimensions - Bucket Spacer-Lower (For EDWP))	-	560	For each component test
3.3, Fig. 6.6(Critical Dimensions - Follower-SDWP)	-	560	For each component test
3.3, Fig. 6.7(Critical Dimensions - Follower-EDWP)	-	560	For each component test
3.3, Fig. 6.8(Critical Dimensions - Follower-VLOM-65)	-	560	For each component test
3.3, Fig. 6.9(Critical Dimensions - Check Valve-Standard (For SDWP & EDWP))	-	560	For each component test
3.3, Fig. 6.11(Critical Dimensions - Rubber Seat Retainer (For SDWP & EDWP))	-	560	For each component test
3.3, Fig. 6.12(Critical Dimensions - Check Valve Seat - Standard (For SDWP & EDWP))	-	560	For each component test
3.3, Fig. 6.13(Critical Dimensions - Check Valve - VLOM-65)	-	560	For each component test
3.3, Fig. 6.14(Critical Dimensions - Cage (For VLOM-65))	-	560	For each component test
3.3, Fig. 6.15(Critical Dimensions - Plunger Valve Body - VLOM-50)	-	560	For each component test
3.3, Fig. 6.16(Critical Dimensions - Check Valve Body - VLOM-50)	-	560	For each component test

31 Jul, 2024

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

4500 View breakup
Single core unsheathed-Rs.4500/-, For each additional core-Rs.1180/-, Maximum-Rs.7810/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	560	For each Test
4.1.1(INSULATION : General Purjose Insulaiion)	-	560	For each Test
4.1.2(INSULATION : Heat Resisting Insulation)	-	560	For each Test
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	560	For each Test
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	560	For each Test
6.1(MATERIALS : ARMGURING)	-	560	For each Test
6.2(MATERIALS : ARMGURING)	-	560	For each Test
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	560	For each Test
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	560	For each Test
8.1(CONSTRUCTION : CONDUCTOR)	-	560	For each Test
8.2(CONSTRUCTION : CONDUCTOR)	-	560	For each Test
9.1(INSULATION )	-	560	For each Test
9.2(INSULATION : Thickness of Insulation)	-	560	For each Test
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	560	For each Test
9.4(INSULATION : Application of Insulation)	-	560	For each Test
10.1(CORE IDENTIFICATION)	-	560	For each Test
10.2(CORE IDENTIFICATION)	-	560	For each Test
10.3(CORE IDENTIFICATION)	-	560	For each Test
10.3.1(Arrangement of Marking)	-	560	For each Test
11.1(LAYING UP OF CORES)	-	560	For each Test
11.2(LAYING UP OF CORES)	-	560	For each Test
12.1(INNER SHEATH)	-	560	For each Test
12.2(INNER SHEATH)	-	560	For each Test
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	560	For each Test
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	560	For each Test
13.1.1(ARMOURING : Application)	-	560	For each Test
13.1.2(Armouring: Coverage )	-	560	For each Test
13.1.3(ARMOURING : Direction of lay )	-	560	For each Test
13.1.4(ARMOURING : Application)	-	560	For each Test
13.2(ARMOURING : Type of Armour)	-	560	For each Test
13.2.1(ARMOURING : Type of Armour)	-	560	For each Test
13.3(Armouring : Dimensions -Wire Diameter)	-	560	For each Test
13.3(Armouring : Dimensions -Formed wire )	-	560	For each Test
13.4(ARMOURING : Joints)	-	560	For each Test
13.5.1(ARMOURING : Resistance)	-	560	For each Test
13.5.2(ARMOURING : Resistance)	-	560	For each Test
13.6 a)(ARMOURING: Tensile Strength)	-	560	For each Test
13.6 b)(ARMOURING: Elongation )	-	560	For each Test
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	560	For each Test
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	560	For each Test
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	560	For each Test
13.6 f)(ARMOURING: Mass of zinc coating )	-	2440	For each Test
13.6 g)(ARMOURING: Resistivity)	-	560	For each Test
14.1(OUTER SHEATH)	-	560	For each Test
14.2(OUTER SHEATH)	-	560	For each Test
14.3(OUTER SHEATH : Colour )	-	560	For each Test
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	560	For each Test
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	560	For each Test
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	560	For each Test
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	560	For each Test
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	560	For each Test
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	560	For each Test
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	560	For each Test
15.1 a) 4)(Resistance test - Neutral conductor )	-	560	For each Test
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	560	For each Test
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	560	For each Test
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	560	For each Test
15.1 d)1)(Physical tests for sheath : Elongation )	-	560	For each Test
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2440	For each Test
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2440	For each Test
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2440	For each Test
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2440	For each Test
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2440	For each Test
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2440	For each Test
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2440	For each Test
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2440	For each Test
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	560	For each Test
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	560	For each Test
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	560	For each Test
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	560	For each Test
15.1 d)4)(Hot deformation : Insulation )	-	560	For each Test
15.1 d)4)(Hot deformation : Sheath )	-	560	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	2440	For each Test
15.1 d)5)( Loss of mass in air oven- sheath )	-	2440	For each Test
15.1 d)6)(Heat shock test- Insulation )	-	560	For each Test
15.1 d)6)(Heat shock test- sheath )	-	560	For each Test
15.1 d)7)(Thermal stability- insulation )	-	560	For each Test
15.1 d)7)(Thermal stability- Sheath )	-	560	For each Test
15.1 e)(Insulation resistance test : Volume Resistivity )	-	560	For each Test
15.1 e)(Insulation resistance test : IR Constant )	-	560	For each Test
15.1 f)(High voltage test ( water immersion test ))	-	560	For each Test
15.1 g)(High voltage test at room temperature)	-	560	For each Test
15.1 g)(High voltage test at room temperature)	-	560	For each Test
15.4 a)(Cold bend test- Insulation ( Optional test))	-	560	For each Test
15.4 a)(Cold bend test- Sheath ( Optional test))	-	560	For each Test
15.4 b)(Cold impact test- Insulation ( Optional test))	-	560	For each Test
15.4 b)(Cold impact test- Sheath ( Optional test))	-	560	For each Test
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	560	For each Test
16.1(DETAILS OF TESTS : General)	-	560	For each Test
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	560	For each Test
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	560	For each Test
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	2440	For each Test
16.4(Flammability Test)	-	560	For each Test
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	560	For each Test
17.2(IDENTIFICATION : Cable Identification)	-	560	For each Test
17.2.1(IDENTIFICATION : Cable Identification)	-	560	For each Test
17.3(IDENTIFICATION : Cable Code)	-	560	For each Test
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	560	For each Test
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	560	For each Test
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	560	For each Test
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	560	For each Test
16.4(Flammability Test- Un affected portion)	-	560	For each Test
16.4(Flammability Test- Period of Burning)	-	560	For each Test
9.3(Minimum Thickness of Reduce core insulation)	-	560	For each Test
9.2(Thickness of Reduce core insulation)	-	560	For each Test
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	560	For each Test

31 Jul, 2024

-
For category 01 only

IS 303 (1989)

Plywood for General Purposes -

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1410	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1410	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	560	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	560	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	560	-
11.3(Moisture Content - Part 1 of IS 1734)	-	560	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	560	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	560	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	560	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	560	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	560	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	560	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	560	-
5.1(Type - For BB Type)	-	560	-
5.1(Type - For AB Type)	-	560	-
5.1(Type - For AA Type)	-	560	-
4(Grade - For MR grade)	-	560	-
4(Grade - For BWR grade)	-	560	-

31 Jul, 2024

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

4500 View breakup
Single coroe unsheathed cable-Rs.4500/-, For each additional core-Rs.1180/-, Maximum-Rs.7810/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	560	For each test
11.2(Legibility)	-	560	For each test
11.1(Durability)	-	560	For each test
11(Identification)	-	560	For each test
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	560	For each test
10.4(Flammability test- Unaffected portion)	-	560	For each test
10.4(Flammability test-Burning after flame removal)	-	560	For each test
table 1 e) 3) (IR constant- max. Temp)	-	560	For each test
table 1 e) 3) (IR constant- Room temp )	-	560	For each test
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	560	For each test
table 1 e) 3) (Volume Resistivity - Room temp )	-	560	For each test
10.2(HV (room temperature))	-	560	For each test
10.1(HV (water immersion))	-	560	For each test
10.1(HV (water immersion))	-	560	For each test
Table 1 iii) d) 9)(Cold impact for sheath)	-	560	For each test
Table 1 iii) d) 8)(Cold bend for sheath)	-	560	For each test
Table 1 iii) c) 9)(Cold impact for insulation)	-	560	For each test
Table 1 iii) c) 8)(Cold bend for insulation)	-	560	For each test
Table 1(Category Code)	-	560	For each test
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	560	For each test
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	560	For each test
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	560	For each test
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	560	For each test
Table 1 iii) d) 5)(Heat shock-Sheath )	-	560	For each test
Table 1 iii) c) 5)(Heat shock-Insulation )	-	560	For each test
Table 1 iii) d) 4)(Cracks Observed)	-	560	For each test
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	560	For each test
Table 1 iii) c) 4)(Cracks Observed)	-	560	For each test
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	560	For each test
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	560	For each test
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	560	For each test
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	560	For each test
Table 1 iii) d) 3)(Sheath- TS variation)	-	560	For each test
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	2440	For each test
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2440	For each test
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	560	For each test
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	560	For each test
Table 1 iii) c) 3)(Elongation variation)	-	560	For each test
Table 1 iii) c) 3)(TS variation)	-	560	For each test
Table 1 iii) c) 3)(Elongation (After ageing))	-	2440	For each test
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	2440	For each test
Table 1 iii) c) 1)(Elongation (Without ageing))	-	560	For each test
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	560	For each test
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	560	For each test
8.3(Thickness of Sheath)	-	560	For each test
5.2(Application )	-	560	For each test
5.3(Thickness of Insulation)	-	560	For each test
9.1(Ovality)	-	560	For each test
9(Overall dimensions)	-	560	For each test
10.11(Per sulphate test (for tinned Cu cable only))	-	560	For each test
4.2(Conductor resistance test)	-	560	For each test
4.1(Wrapping test (for Al))	-	560	For each test
4.1(Tensile test (for Al)- After Stranding)	-	560	For each test
4.1(Tensile test (for Al)-Before Stranding)	-	560	For each test
4.1(Annealing test (for copper))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	560	For each test
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	560	For each test
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	560	For each test
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	560	For each test
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	560	For each test
(Cl.16.1) (Cl.19.1)(Conductor)	-	560	For each test
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	560	For each test
12(CONSTRUCTION Core Identification)	-	560	For each test
8.1(Sheath Material )	-	560	For each test
7(Binder Tape)	-	560	For each test
6.2(Filler)	-	560	For each test
6.1(Filler)	-	560	For each test
5.1(Insulation)	-	560	For each test
4.4(Joints in Conductor)	-	560	For each test
4.1(Conductor - Material)	-	560	For each test
10.11(Persulphate Test )	-	560	For each test
12.0(Core identification)	-	560	For each test
4, IS 8130(Construction of conductor)	-	560	For each test
Table 2, IS 8130(No fo wire in a conductor)	-	560	For each test
8.3(Minimum thickness of Sheath)	-	560	For each test
8.3(Avarage thickness of Sheath)	-	560	For each test
5.3(Minimum thickness of insulation)	-	560	For each test
5.3(Avarage thickness of insulation)	-	560	For each test

31 Jul, 2024

-
Facility For category 01, 02 only

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(a) Size)	-	560	For each test.
11(b) Construction)	-	560	For each test.
11(c) tensile designation)	-	560	For each test.
11(d) lay)	-	560	For each test.
11(e) coating)	-	560	For each test.
11(f) length)	-	560	For each test.
11( g) mass)	-	560	For each test.
11(h) manufacturer's name or trade mark)	-	560	For each test.
11(i) lot number along with the order number)	-	560	For each test.
11(j) BIS Standards Mark)	-	560	For each test.
5(a) Grade)	-	560	For each test.
5(b) Tensile Grade)	-	560	For each test.
6(a) Lay)	-	560	For each test.
6(b) Construction)	-	560	For each test.
11(c) tensile designation)	-	560	For each test.
7(Freedom from defects)	-	560	For each test.
9(a) Tensile)	-	560	For each test.
9(b) Elongation)	-	560	For each test.
9(c) Galvanizing Test)	-	560	For each test.
11(a) Size)	-	560	For each test.
11(b) Construction)	-	560	For each test.
11(d) lay)	-	560	For each test.
11(e) coating)	-	560	For each test.
11(f) length)	-	560	For each test.
11( g) mass)	-	560	For each test.
11(h) manufacturer's name or trade mark)	-	560	For each test.
11(j) BIS Standards Mark)	-	560	For each test.
5(a) Grade)	-	560	For each test.
5(b) Tensile Grade)	-	560	For each test.
6(a) Lay)	-	560	For each test.
6(b) Construction)	-	560	For each test.
7(Freedom from defects)	-	560	For each test.
9(a) Tensile)	-	560	For each test.
9(b) Elongation)	-	560	For each test.
9(c) Galvanizing Test)	-	560	For each test.
4(S)	-	560	For each test.
4(P)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-	560	For each test.For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-	560	For each test.
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	560	For each test.

31 Jul, 2024

-
-

IS 12427 (2001)

Fasteners - Threaded steel fasteners - Hexagon head transmission tower bolts - Specification (First Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Designation)	-	560	For each test
Cl 3.1, Cl 3.2, Fig-1, Table-1 & Table-2(Dimensions)	-	560	For each test
Cl 3.3, IS 4218(Pt 1 to 4) & IS 2334(Threads)	-	560	For each test
Cl 5.1 & IS 14394(Nuts)	-	560	For each test
Cl 5.2, IS 2016 & IS 4759(Washers)	-	560	For each test
Cl 6.1 & IS 1367(Pt 3)(Bolt Tensile,Proof,Wedge Loading,Hardness Test)	-	1800	For Bolt Tensile,Proof,Wedge Loading,Hardness Test.
Cl 6.2(Bolt Shear Strength)	-	560	For each test
Cl 7 & IS 1367(Pt 13)(Finish)	-	560	For each test
Cl 8 & IS 1367(Pt 9/Sec1)(General Requirements)	-	560	For each test

31 Jul, 2024

-
-

IS 9825 (2003)

Chlorine tablets - Specification (Second Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(Description)	-	560	For each test.
Cl.4.3(Size (Mass of tablet))	-	560	For each test.
Cl.4.3(Available Chlorine (Annex A))	-	560	For each test.
Cl.4.4(Moisture (Annex B))	-	560	For each test.
Cl.4.4(Shelf Life (Annex A))	-	560	For each test.

31 Jul, 2024

-
-

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	560	For each test.
Cl 12(Workmanship)	-	560	For each test.
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	1210	For Tensile Test, Flattening Test & Bend Test.
Cl 15(Workmanship)	-	560	For each test.
Cl 8(Outer Diameter, Thickness & Mass)	-	560	For each test.
7, 6.1.1(CARBON)	-	560	For each test.
7, 6.1.1(SULPHUR)	-	560	For each test.
7, 6.1.1(PHOSPHURS)	-	560	For each test.
7, 6.1.1(MANGANESE)	-	560	For each test.
7, 6.1.1(NITROGEN)	-	560	For each test.
7, 6.1.1(SILICON)	-	560	For each test.
7, 6.1.1(ALUMINIUM)	-	560	For each test.

31 Jul, 2024

-
For plain ended only

IS 2556 : Part 3 (2004)

Vitreous Sanitary Appliances (Vitreous China) - - Part 3: Specific Requirements of Squatting Pans

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	560	For each test
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	560	For each test
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	560	For each test
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	690	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	560	For each test
3(General requirements-Thickness IS 2556 (Part 1))	-	560	For each test
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	560	For each test
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	560	For each test
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	560	For each test
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	560	For each test
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	560	For each test
4(PATTERNS )	-	560	For each test
4(SIZE)	-	560	For each test
5.1(CONSTRUCTION)	-	560	For each test
5.1.1(CONSTRUCTION)	-	560	For each test
5.2(CONSTRUCTION)	-	560	For each test
5.3(CONSTRUCTION)	-	560	For each test
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	560	For each test
6.1-Table 1(DIMENSIONS AND TOLERANCES-B)	-	560	For each test
6.1-Table 2(DIMENSIONS AND TOLERANCES-F)	-	560	For each test
6.1-Table 3(DIMENSIONS AND TOLERANCES-H)	-	560	For each test
6.1-Table 4(DIMENSIONS AND TOLERANCES-J)	-	560	For each test
6.1-Table 5(DIMENSIONS AND TOLERANCES-Slope of bottom of pan)	-	560	For each test
6.1-Table 6(DIMENSIONS AND TOLERANCES-L)	-	560	For each test
6.1-Table 7(DIMENSIONS AND TOLERANCES-N)	-	560	For each test
6.1-Table 8(DIMENSIONS AND TOLERANCES-P)	-	560	For each test
6.2-Table 2(DIMENSIONS AND TOLERANCES-C)	-	560	For each test
6.2-Table 3(DIMENSIONS AND TOLERANCES-D)	-	560	For each test
6.2-Table 4(DIMENSIONS AND TOLERANCES-E)	-	560	For each test
6.2-Table 5(DIMENSIONS AND TOLERANCES-G)	-	560	For each test
6.2-Table 6(DIMENSIONS AND TOLERANCES-K)	-	560	For each test
6.2-Table 7(DIMENSIONS AND TOLERANCES-M)	-	560	For each test
6.2(DIMENSIONS AND TOLERANCES-top surface variation)	-	560	For each test
7(FINLSH)	-	560	For each test
8.1(FLUSHING TESTS-Toilet Paper Test)	-	560	For each test
8.2(FLUSHING TESTS-Smudge Test)	-	560	For each test
8.3(FLUSHING TESTS-Water Holding Capacity Test)	-	560	For each test
8.4(FLUSHING TESTS-Saw Dust Test)	-	560	For each test
8.5(FLUSHING TESTS-Splash Test)	-	560	For each test

31 Jul, 2024

-
-

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	510	For each test.
Cl 9(Press)	-	560	For each test.
Cl 11(Workmanship)	-	560	For each test.
Cl 12 & 13(Length, Width & Thickness)	-	560	For each test.
Cl 8 & Table 3(UTM)	-	510	For each test.
Cl 9(Press)	-	560	For each test.
Cl 11(Workmanship)	-	560	For each test.
Cl 12 & 13(Length, Width & Thickness)	-	560	For each test.
7.1(Carbon %)	-	560	For each test.
7.1(Manganese %)	-	560	For each test.
7.1(Phosphorus %)	-	560	For each test.
7.1(Sulphur %)	-	560	For each test.
7.1(Silicon %)	-	560	For each test.
7.1( Copper %)	-	560	For each test.
7.1( Aluminium %)	-	560	For each test.
7.1( Nb)	-	560	For each test.
7.1(V)	-	560	For each test.
7.1( Ti)	-	560	For each test.
7.1(Cr)	-	560	For each test.
7.1(Mo)	-	560	For each test.
7.1(Ni)	-	560	For each test.
7.1( Nitrogen%)	-	560	For each test.
7.1(CE)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(TITANIUM)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(VANADIUM)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(NIOBIUM)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(CARBON EQUIVELENT )	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(Molybdenum)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(Chromium)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(Nickel)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )( ALUMINIUM)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(SILICON)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(NITROGEN)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(MANGANESE)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(PHOSPHURS)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )(SULPHUR)	-	560	For each test.
Table 1 ( Clauses 7.1 ,7.2 )( CARBON)	-	560	For each test.

31 Jul, 2024

-
-

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	560	For each test.
Cl 9(Tensile Test On UTM)	-	510	For each test.
Cl 11(Workmanship)	-	560	For each test.
Cl 13(Workmanship)	-	560	For each test.
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	560	For each test.
Cl 9(Tensile Test On UTM)	-	510	For each test.
Cl 11(Workmanship)	-	560	For each test.
Cl 13(Workmanship)	-	560	For each test.
6 AND AS PER IS 7887(MICRO ALLOY)	-	560	For each test.
6 AND AS PER IS 7887(ALUMINIUM)	-	560	For each test.
6 AND AS PER IS 7887(PHOSPHORUS)	-	560	For each test.
6 AND AS PER IS 7887(SULPHUR)	-	560	For each test.
6 AND AS PER IS 7887(MANGANESE)	-	560	For each test.
6 AND AS PER IS 7887(SILICON)	-	560	For each test.
6 AND AS PER IS 7887(CARBON)	-	560	For each test.
7 & 8(Ovality)	-	560	For each test.
7 & 8(Diameter)	-	560	For each test.
9.2(Wrapping Test)	-	560	For each test.

31 Jul, 2024

-
-

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	900	For material test.
13(Mechanical Testing)	-	2330	For Mechanical Testing
6.0(Workmanship)	-	560	For each test
8.0(Straightness)	-	560	For each test
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	560	For each test
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	560	For each test
13.1.3(Tensile Strength)	-	510	For each test
13.1.1(Yield Stress)	-	510	For each test
13.1.2(Elongation)	-	510	For each test
13.2(Flattening Test)	-	350	For each test
13.3(Bend Test (Strip))	-	350	For each test
13.4(Bend Test (Whole Tube))	-	350	For each test
13.5(Drift Expansion Test)	-	560	For each test
13.6(Crush Test)	-	560	For each test
19.1.3(Height of Internal Fin)	-	560	For each test
4.1(Sulphur-Percentage by mass)	-	450	For each test
4.1(Phosphorus-Percentage by mass)	-	450	For each test

31 Jul, 2024

-
-

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type A/Type B)	-	560	For each test
5 Table-1(Sizes Diameter of Line wire)	-	560	For each test
5 Table-1(Sizes Diamater of Point wire)	-	560	For each test
5 Table-1(Sizes Mass of Completed barbed wire)	-	560	For each test
5 Table-1(Sizes Distance between two barbs)	-	560	For each test
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	560	For each test
7.1(Manufacture)	-	560	For each test
7.2(Manufacture)	-	560	For each test
7.3(Manufacture)	-	560	For each test
8(CHROMATING)	-	560	For each test
9.1(Freedom from defects)	-	560	For each test
9.2(Freedom from defects)	-	560	For each test
12.1(Tensile Strength)	-	510	For each test
12.2.1(Mass of zinc coating (line wire))	-	560	For each test
12.2.2(Mass of zinc coating (point wire))	-	560	For each test
12.2(Uniformity of zinc coating)	-	560	For each test
12.3(Ductility)	-	560	For each test

31 Jul, 2024

-
-

IS 710 (2010)

Marine plywood - Specification (Second Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(MARKING)	-	560	For complete test.
11.2(MARKING)	-	560	For each test.
7.1(WORKMANSHIP AND FINISH )	-	560	For each test.
7.2(WORKMANSHIP AND FINISH )	-	560	For each test.
7.3(WORKMANSHIP AND FINISH )	-	560	For each test.
7.5(WORKMANSHIP AND FINISH )	-	560	For each test.
6.1(DIMENSIONS)	-	560	For each test.
6.2(DIMENSIONS)	-	560	For each test.
6.3(DIMENSIONS)	-	560	For each test.
9.1.1(MOISTURE CONTENT)	-	560	For each test.
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	560	For each test.
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	560	For each test.
9.1.3 , 9.1.3.1.1(Water resistance test)	-	560	For each test.
9.1.3 , 9.1.3.1.2(Water resistance test)	-	560	For each test.
9.1.5(Mycological test)	-	560	For each test.
9.1.5 , 9.1.3.1.2(Mycological test)	-	560	For each test.
9.1.4(Tensile strength)	-	510	For each test.
9.1.6 (Table 3)(Static bending strength)	-	1410	For each test.
9.1.6 (Table 3)(Static bending strength)	-	1410	For each test.
9.1.7 (Table 4)(Wet bending strength)	-	1410	For each test.
9.1.7 (Table 4)(Wet bending strength)	-	1410	For each test.
9.1.8(Retention of preservative)	-	560	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1410	For each test.
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1410	For each test.
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	510	For each test.
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	510	For each test.
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	510	For each test.
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	560	For each test.
Cl.9.1.5,9.1.3.1.1 (Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	560	For each test.
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	560	For each test.
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	560	For each test.
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	560	For each test.
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	560	For each test.

31 Jul, 2024

-
-

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1( Insouble matter, Grade 1, A-3)	-	560	For each test.
1 (i) Table 1( Insouble matter, Grade 2, A-3)	-	560	For each test.
1 (i) Table 1( Insouble matter, Grade 3, A-3)	-	560	For each test.
1 (i) Table 1( Insouble matter, Grade 4, A-3)	-	560	For each test.
1 (i) Table 1( Insouble matter, Grade 5, A-3)	-	560	For each test.
1 (ii) Table 1(Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-	560	For each test.
1 (ii) Table 1(Soluble iron compound (as Fe2+ and Fe3+), Grade 2, A-4)	-	560	For each test.
1 (ii) Table 1(Soluble iron compound (as Fe2+ and Fe3+), Grade 3, A-4)	-	560	For each test.
1 (ii) Table 1(Soluble iron compound (as Fe2+ and Fe3+), Grade 4, A-4)	-	560	For each test.
1 (ii) Table 1(Soluble iron compound as Fe2+ and Fe3+), Grade 5, A-4)	-	560	For each test.
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-	560	For each test.
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 2, A-5)	-	560	For each test.
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 3, A-5)	-	560	For each test.
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 4, A-5)	-	560	For each test.
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 5, A-5)	-	560	For each test.
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 1, A-6)	-	560	For each test.
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 2, A-6)	-	560	For each test.
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 3, A-6)	-	560	For each test.
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 4, A-6)	-	560	For each test.
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 5, A-6)	-	560	For each test.
1 (v) Table 1(Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-	560	For each test.
1 (v) Table 1(Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 2, A-7)	-	560	For each test.
1 (v) Table 1(Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 3, A-7)	-	560	For each test.
1 (v) Table 1(Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 4, A-7)	-	560	For each test.
1 (vi) Table 1( Lead (as Pb), Grade 1, A-8)	-	560	For each test.
1 (vi) Table 1( Lead (as Pb), Grade 2, A-8)	-	560	For each test.
1 (vi) Table 1( Lead (as Pb), Grade 3, A-8)	-	560	For each test.
1 (vi) Table 1( Lead (as Pb), Grade 4, A-8)	-	560	For each test.
1 (vi) Table 1( Lead (as Pb), Grade 5, A-8)	-	560	For each test.
1 (vii) Table 1(Arsenic (as As2O3), Grade 1, A-9)	-	560	For each test.
1 (vii) Table 1(Arsenic (as As2O3), Grade 2, A-9)	-	560	For each test.
1 (vii) Table 1(Arsenic (as As2O3), Grade 3, A-9)	-	560	For each test.
1 (vii) Table 1(Arsenic (as As2O3), Grade 4, A-9)	-	560	For each test.
1 (vii) Table 1(Arsenic (as As2O3), Grade 5, A-9)	-	560	For each test.
1 (viii) Table 1(Mercury (as Hg), Grade 1, A-10)	-	560	For each test.
1 (viii) Table 1(Mercury (as Hg), Grade 2, A-10)	-	560	For each test.
1 (viii) Table 1(Mercury (as Hg), Grade 3, A-10)	-	560	For each test.
1 (viii) Table 1(Mercury (as Hg), Grade 4, A-10)	-	560	For each test.
1 (viii) Table 1(Mercury (as Hg), Grade 5, A-10)	-	560	For each test.
1 (ix) Table 1(Manganese (as Mn), Grade 1, A-11)	-	560	For each test.
1 (ix) Table 1(Manganese (as Mn), Grade 2, A-11)	-	560	For each test.
1 (ix) Table 1(Manganese (as Mn), Grade 3, A-11)	-	560	For each test.
1 (ix) Table 1(Manganese (as Mn), Grade 4, A-11)	-	560	For each test.
1 (ix) Table 1(Manganese (as Mn), Grade 5, A-11)	-	560	For each test.
1 (x) Table 1(Chromium (as Cr), Grade 1, A-12)	-	560	For each test.
1 (x) Table 1(Chromium (as Cr), Grade 2, A-12)	-	560	For each test.
1 (x) Table 1(Chromium (as Cr), Grade 3, A-12)	-	560	For each test.
1 (x) Table 1(Chromium (as Cr), Grade 4, A-12)	-	560	For each test.
1 (x) Table 1(Chromium (as Cr), Grade 5, A-12)	-	560	For each test.
1 (xi) Table 1(Cadmium (as Cd), Grade 1, A-13)	-	560	For each test.
1 (xi) Table 1(Cadmium (as Cd), Grade 2, A-13)	-	560	For each test.
1 (xi) Table 1(Cadmium (as Cd), Grade 3, A-13)	-	560	For each test.
1 (xi) Table 1(Cadmium (as Cd), Grade 4, A-13)	-	560	For each test.
1 (xi) Table 1(Cadmium (as Cd), Grade 5, A-13)	-	560	For each test.
1 (xii) Table 1(Selenium (as Se), Grade 1, A-14)	-	560	For each test.
1 (xii) Table 1(Selenium (as Se), Grade 2, A-14)	-	560	For each test.
1 (xii) Table 1(Selenium (as Se), Grade 3, A-14)	-	560	For each test.
1 (xii) Table 1(Selenium (as Se), Grade 4, A-14)	-	560	For each test.
1 (xii) Table 1(Selenium (as Se), Grade 5, A-14)	-	560	For each test.
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 1, A-15)	-	560	For each test.
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 2, A-15)	-	560	For each test.
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 3, A-15)	-	560	For each test.
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 4, A-15)	-	560	For each test.
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 5, A-15)	-	560	For each test.
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 1, A-16)	-	560	For each test.
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 2, A-16)	-	560	For each test.
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 3, A-16)	-	560	For each test.
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 4, A-16)	-	560	For each test.
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 5, A-16)	-	560	For each test.

31 Jul, 2024

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	560	For each test.
Cl 12.2(Concavity & Convexity )	-	560	For each test.
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	560	For each test.
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	560	For each test.
Cl 12.5(Water absorption)	-	690	For each test.
Cl 12.6(Wet transverse strength )	-	510	For each test.
Cl 12.7(Resistance to wear)	-	510	For each test.
Cl 11(Suface Finish)	-	560	For each test.
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	560	For each test.
Cl 12.2(Concavity & Convexity )	-	560	For each test.
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	560	For each test.
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	560	For each test.
Cl 12.5(Water absorption)	-	690	For each test.
Cl 12.6(Wet transverse strength )	-	510	For each test.
Cl 12.7(Resistance to wear)	-	510	For each test.
Cl 11(Suface Finish)	-	560	For each test.

31 Jul, 2024

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	560	For each test.
Cl 7(Workmanship)	-	560	For each test.
Cl 8(Workmanship)	-	560	For each test.
Cl 9(Workmanship)	-	560	For each test.
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1210	For Tensile Test, Flattening Test & Cold Bend Test
Cl 13(Workmanship)	-	560	For each test.
Cl 6(Outer Diameter, Thickness & Mass)	-	560	For each test.
Cl 7(Workmanship)	-	560	For each test.
Cl 8(Workmanship)	-	560	For each test.
Cl 9(Workmanship)	-	560	For each test.
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1250	For Tensile Test, Flattening Test & Cold Bend Test
Cl 13(Workmanship)	-	560	For each test.
Cl 6(Outer Diameter, Thickness & Mass)	-	560	For each test.
Cl 7(Workmanship)	-	560	For each test.
Cl 8(Workmanship)	-	560	For each test.
Cl 9(Workmanship)	-	560	For each test.
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1250	For Tensile Test, Flattening Test & Cold Bend Test
Cl 13(Workmanship)	-	560	For each test.
8 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	560	For each test.
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	560	For each test.
5 AND AS PER IS 10748(COPPER)	-	560	For each test.
5 AND AS PER IS 10748(MICRO ALLOY)	-	560	For each test.
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	560	For each test.
5 AND AS PER IS 10748(CARBON)	-	560	For each test.
Clause - 5.1, Table-3( ALUMINIUM)	-	560	For each test.
Clause - 5.1, Table-3(SILICON)	-	560	For each test.
Clause - 5.1, Table-3(NITROGEN)	-	560	For each test.
Clause - 5.1, Table-3(MANGANESE)	-	560	For each test.

31 Jul, 2024

-
For dia upto 25mm

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(UTM)	-	560	For each test.
Cl 9(Press)	-	560	For each test.
Cl 10(Die Press)	-	560	For each test.
Cl 12(Workmanship)	-	560	For each test.
Cl 13(Length, Width & Thickness)	-	560	For each test.
6.1(Carbon %)	-	560	For each test.
6.1(Manganese %)	-	560	For each test.
6.1(Phosphorus %)	-	560	For each test.
6.1(Sulphur %)	-	560	For each test.
6.1(Silicon %)	-	560	For each test.
6.1( Copper %)	-	560	For each test.
6.1( Aluminium %)	-	560	For each test.
6.1( Nb)	-	560	For each test.
6.1(V)	-	560	For each test.
6.1( Ti)	-	560	For each test.
6.1(Cr)	-	560	For each test.
6.1(Mo)	-	560	For each test.
6.1(Ni)	-	560	For each test.
6.1( Nitrogen%)	-	560	For each test.
6.1(Microalloying)	-	560	For each test.

31 Jul, 2024

-
-

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	560	For each test.
Cl 8.2(Press)	-	560	For each test.
Cl 10(Galvanising Test)	-	560	For each test.
Cl 12(Workmanship)	-	560	For each test.
Cl 13(Weight)	-	560	For each test.
Cl 14(Length, Width & Thickness)	-	560	For each test.
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Difference between Diagonal))	-	560	For each test.
Cl. 14 & Cl. 15 (Cl. 14 & Cl. 15 (Thickness))	-	560	For each test.
Cl. 14 (Cl. 14 & Cl 15 (Width))	-	560	For each test.
Cl. 14 (Cl. 14 & Cl 15 (Length))	-	560	For each test.
Cl.12(Freedom from defects)	-	560	For each test.
Cl. 8.1 (Cl. 8.1 (Percentage Elongation ))	-	510	For each test.
Cl. 8.1 (Cl. 8.1 (Yield Stress))	-	510	For each test.
Cl. 8.1 (Cl. 8.1 (Tensile Strength))	-	510	For each test.
7.4(Mass of Coating: Single Spot Test)	-	560	For each test.
7.4(Mass of Coating: Triple Spot Test)	-	560	For each test.
7.1 & 10.2(Mass of Coating: Single Spot Test)	-	560	For each test.
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	560	For each test.
5.1(phosphorus)	-	560	For each test.
5.1(copper)	-	560	For each test.
5.1(nitrogen)	-	560	For each test.
5.1(micro alloy)	-	560	For each test.
5.1(aluminium)	-	560	For each test.
5.1(manganese)	-	560	For each test.
5.1(phosphorus)	-	560	For each test.
5.1(sulphur)	-	560	For each test.
5.1(carbon)	-	560	For each test.
5.1(Titanium)	-	560	For each test.
Cl. 17(Marking )	-	560	For each test.
Cl. 14 & Cl. 15(Pitch of corrugation (average of 4))	-	560	For each test.
Cl. 14 & Cl. 15(Depth of corrugation (average of 4))	-	560	For each test.
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Number of Corrugation))	-	560	For each test.
cl 5.1, T-1, Note-6, For reinforced steel(P)	-	560	For each test.
cl 5.1, T-1, Note-5, For Microalloying elements(Nb+V+Ti+B)	-	560	For each test.
cl 5.1, T-1, Note-5, For Microalloying elements(B)	-	560	For each test.
cl 5.1, T-1, Note-5, For Microalloying elements(Ti)	-	560	For each test.
cl 5.1, T-1, Note-5, For Microalloying elements(V)	-	560	For each test.
cl 5.1, T-1, Note-5, For Microalloying elements(Nb)	-	560	For each test.
cl 5.1, T-1, Note-4, For Cu bearing quality(Cu)	-	560	For each test.
cl 5.1, T-1, Note-2, When Al-Si killed(Si)	-	560	For each test.
cl 5.1, T-1, Note-2, When Al-Si killed(Al)	-	560	For each test.
cl 5.1, T-1, Note-2, When Si killed(Si)	-	560	For each test.
cl 5.1, T-1, Note-2, When Al killed(Al)	-	560	For each test.
cl 5.1, T-1, Note-3(N2)	-	560	For each test.
cl 5.1, T-1, designation For GP 550(P)	-	560	For each test.
cl 5.1, T-1, designation For GP 550(S)	-	560	For each test.
cl 5.1, T-1, designation For GP 550(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP 550(C)	-	560	For each test.
cl 5.1, T-1, Note-3(N2)	-	560	For each test.
cl 5.1, T-1, designation For GP 450(P)	-	560	For each test.
cl 5.1, T-1, designation For GP 450(S)	-	560	For each test.
cl 5.1, T-1, designation For GP 450(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP 450(C)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-2(P)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-2(S)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-2(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-2(C)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-1(P)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-1(S)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-1(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP 350 class-1(C)	-	560	For each test.
cl 5.1, T-1, designation For GP 300(P)	-	560	For each test.
cl 5.1, T-1, designation For GP 300(S)	-	560	For each test.
cl 5.1, T-1, designation For GP 300(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP 300(C)	-	560	For each test.
cl 5.1, T-1, designation For GP275(P)	-	560	For each test.
cl 5.1, T-1, designation For GP275(S)	-	560	For each test.
cl 5.1, T-1, designation For GP275(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP275(C)	-	560	For each test.
cl 5.1, T-1, designation For GP250(P)	-	560	For each test.
cl 5.1, T-1, designation For GP250(S)	-	560	For each test.
cl 5.1, T-1, designation For GP250(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP250(C)	-	560	For each test.
cl 5.1, T-1, designation For GP230(P)	-	560	For each test.
cl 5.1, T-1, designation For GP230(S)	-	560	For each test.
cl 5.1, T-1, designation For GP230(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP230(C)	-	560	For each test.
cl 5.1, T-1, designation For GPIF(P)	-	560	For each test.
cl 5.1, T-1, designation For GPIF(S)	-	560	For each test.
cl 5.1, T-1, designation For GPIF(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GPIF(C)	-	560	For each test.
cl 5.1, T-1, designation For GPED(P)	-	560	For each test.
cl 5.1, T-1, designation For GPED(S)	-	560	For each test.
cl 5.1, T-1, designation For GPED(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GPED(C)	-	560	For each test.
cl 5.1, T-1, designation For GPD(P)	-	560	For each test.
cl 5.1, T-1, designation For GPD(S)	-	560	For each test.
cl 5.1, T-1, designation For GPD(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GPD(C)	-	560	For each test.
cl 5.1, T-1, designation For GPL(P)	-	560	For each test.
cl 5.1, T-1, designation For GPL(S)	-	560	For each test.
cl 5.1, T-1, designation For GPL(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GPL(C)	-	560	For each test.
cl 5.1, T-1, designation For GC(P)	-	560	For each test.
cl 5.1, T-1, designation For GC(S)	-	560	For each test.
cl 5.1, T-1, designation For GC(Mn)	-	560	For each test.
cl 5.1, T-1, designation For GC(C)	-	560	For each test.
cl 5.1, T-1, designation For GPH (P)	-	560	For each test.
cl 5.1, T-1, designation For GPH (S)	-	560	For each test.
cl 5.1, T-1, designation For GPH (Mn)	-	560	For each test.
cl 5.1, T-1, designation For GPH (C)	-	560	For each test.
cl 5.1, T-1, designation For GP (P)	-	560	For each test.
cl 5.1, T-1, designation For GP (S)	-	560	For each test.
cl 5.1, T-1, designation For GP (Mn)	-	560	For each test.
cl 5.1, T-1, designation For GP (C)	-	560	For each test.

31 Jul, 2024

-
-

IS 1363 : Part 3 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grade ˜C ™ Part 3 (Style 1) Hexagon Nuts ( Size Range M 5 to M 64 ) ( Fifth Revision )

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-D)	-	560	For each test
3-Table 1(Dimensions-P)	-	560	For each test
3-Table 1(Dimensions-dw(minimum))	-	560	For each test
3-Table 1(Dimensions-e(minimum))	-	560	For each test
3-Table 1(Dimensions-m(minimum))	-	560	For each test
3-Table 2(Dimensions-D)	-	560	For each test
3-Table 2(Dimensions-P)	-	560	For each test
3-Table 2(Dimensions-dw(minimum))	-	560	For each test
3-Table 2(Dimensions-e(minimum))	-	560	For each test
3-Table 2(Dimensions-m(minimum))	-	560	For each test
3-Table 2(Dimensions-s(minimum))	-	560	For each test
4-Table 3(General requirements)	-	560	For each test
4-Table 3(Threads-ISO 724 & 965(1))	-	560	For each test
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	510	For each test
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	510	For each test
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1) HRB)	-	390	For each test
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	390	For each test
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	690	For each test
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	560	For each test
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	690	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1)- Chamfer Circle)	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear Bursts-Circular head screws (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Raw material, seams and laps- (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Tool marks (ISO 6157-1))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1) (Impairs Usability))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-- Quench cracks (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3) Chamfer Circle)	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Width (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Depth (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Voids- (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Folds- (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	560	For each test
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	560	For each test

31 Jul, 2024

-
-

IS 5820 (1970)

Specification for precast concrete cable covers

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-Table 1(Dimensions-Class)	-	560	For each test
4-Table 1(Dimensions-Type no.)	-	560	For each test
4-Table 1(Dimensions-Shape)	-	560	For each test
4-Table 1(Dimensions-L)	-	560	For each test
4-Table 1(Dimensions-W)	-	560	For each test
4-Table 1(Dimensions-T)	-	560	For each test
4-Table 1(Dimensions-T')	-	560	For each test
6(FINISH)	-	560	For each test
8.2(mpact Strength)	-	690	For each test
2.2.1(Size of aggregates)	-	1410	For each test

31 Jul, 2024

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	560	For each test.
Cl 6.2(Diameter & Ovality)	-	560	For each test.
Cl 6.2(Weight)	-	560	For each test.
Cl 8.2(Bend test)	-	560	For each test.
Cl 9.3(Press)	-	560	For each test.
Clause -4, 4.3(TITANIUM)	-	560	For each test.
Clause -4, 4.2(VANADIUM)	-	560	For each test.
Clause -4, 4.1(NIOBIUM)	-	560	For each test.
Clause -4, 4.1(Molybdenum)	-	560	For each test.
Clause -4, 4.1(Chromium)	-	560	For each test.
Clause -4, 4.1(Nickel)	-	560	For each test.
Clause -4, 4.1( ALUMINIUM)	-	560	For each test.
Clause -4, 4.1(SILICON)	-	560	For each test.
Clause -4, 4.1(NITROGEN)	-	560	For each test.
Clause -4, 4.1(MANGANESE)	-	560	For each test.
Clause -4, 4.1(PHOSPHURS)	-	560	For each test.
Clause -4, 4.1(SULPHUR)	-	560	For each test.
Clause -4, 4.1( CARBON)	-	560	For each test.
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	560	For each test
Cl. 8.1 Table 1(Elongation)	-	560	For each test
Cl. 8.1 Table 1(Yield Stress)	-	560	For each test

31 Jul, 2024

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	560	For each test.
Cl 5 & 6(Diameter)	-	560	For each test.
Cl 7(UTM)	-	510	For each test.
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	350	For each test.
Clause 3.1.1(Sulphur)	-	560	For each test.
Clause 3.1.1(Phosphorus)	-	560	For each test.

31 Jul, 2024

-
-

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Diameter)	-	310	For each test
Cl 5.1.2(Weight)	-	390	For each test
Cl 6.1(Tensile Test On UTM)	-	510	For each test
Cl 6.2(Tensile Test On UTM)	-	510	For each test
Cl 6.3(Tensile Test On UTM)	-	510	For each test
3.1.1(PHOSPHORUS)	-	560	-
3.1.1(SULPHUR)	-	450	For each test

31 Jul, 2024

-
-

IS 1838 : Part 1 (1983)

preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type): Part 1 Bitumen impregnated fibre - Specification

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions and tolerances)	-	560	For each test.
5 Table-1 i(Resistance to handling)	-	560	For each test.
5 Table-1 ii(Recovery in accordance with IS 10566:1983)	-	510	For each test.
5 Table-1 iii(Compression test in accordance with IS 10566:1983)	-	560	For each test.
5 Table-1 iv(Extrusion in accordance with IS 10566:1983)	-	560	For each test.
5 Table-1 v(Water absorption test in accordance with IS 10566:1983)	-	690	For each test.
5 Table-1 vi(Test for Density in accordance with IS 10566:1983 )	-	560	For each test.
5 Table-1 vii(Test for Bitumen content in accordance with IS 10566:1983)	-	560	For each test.
5 Table-1 viii(Weathering test in accordance with IS 10566:1983)	-	1680	For each test.
5 Table-1 ix(Penetration of recovered Bitumen in accordance with IS 10566:1983)	-	560	For each test.
7(Marking)	-	560	For each test.

31 Jul, 2024

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

4500 View breakup
Single core unsheathed-Rs.4500/-, For each additional core-Rs.1180/-, Maximum-Rs.7810/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	560	For each test
4(INSULATION : MATERIALS)	-	560	For each test
5.1(FILLER AND INNER SHEATH)	-	560	For each test
5.2(FILLER AND INNER SHEATH)	-	560	For each test
6(ARMOURING)	-	560	For each test
7(OUTER SHEATH)	-	560	For each test
8.1(CONDUCTOR: CONSTRUCTION)	-	560	For each test
8.2(PROTECTIVE BARRIER)	-	560	For each test
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	560	For each test
9.1(Insulation Applied by extrusicn)	-	560	For each test
9.2(Thickness of Insulation - Average)	-	560	For each test
9.3(Thickness of Insulation - Minimum)	-	560	For each test
9.4(Application of Insulation)	-	560	For each test
10.1(Core Identification)	-	560	For each test
10.2(Core Identification- Neutral)	-	560	For each test
10.3(Core Identification by number )	-	560	For each test
10.4(Core Identification by number - Neutral )	-	560	For each test
11(LAVING UP OF CORES)	-	560	For each test
12.1 & 12.2(Inner sheath : Application)	-	560	For each test
12.3(Thickness of Inner Sheath)	-	560	For each test
13.1(Armouring: Application)	-	560	For each test
13.1.2(Armouring: Coverage )	-	560	For each test
13.1.3(Armouring: Direction of Lay )	-	560	For each test
13.2(Type of armour )	-	560	For each test
13.3(Armouring : Dimensions -Wire Diameter)	-	560	For each test
13.3(Armouring : Dimensions -Formed wire )	-	560	For each test
13.4(Armour: Joint)	-	560	For each test
13.5(Armouring : Resistance Test)	-	560	For each test
13.6 a)(ARMOURING: Tensile Strength)	-	560	For each test
13.6 b)(ARMOURING: Elongation )	-	560	For each test
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	560	For each test
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	560	For each test
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	560	For each test
13.6 f)(ARMOURING: Mass of zinc coating )	-	560	For each test
13.6 g)(ARMOURING: Resistivity)	-	560	For each test
14.1(Outer Sheath : Application)	-	560	For each test
14.2(Colour of outer sheath)	-	560	For each test
14.3(Thickness of outer sheath - AVERAGE)	-	560	For each test
15.1 a) i)(Annealing Test ( For copper wire ) )	-	560	For each test
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	560	For each test
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	560	For each test
15.1 a) iii)(Wrapping test (for aluminium))	-	560	For each test
15.1 a) iv)(Resistance test - Main conductor)	-	560	For each test
15.1 a) iv)(Resistance test - Neutral conductor)	-	560	For each test
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	560	For each test
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	560	For each test
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	560	For each test
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	560	For each test
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	560	For each test
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	560	For each test
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	560	For each test
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	560	For each test
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	2440	For each test
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	560	For each test
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	560	For each test
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2440	For each test
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2440	For each test
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2440	For each test
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2440	For each test
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	560	For each test
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	560	For each test
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	560	For each test
15.1 e) v) (Sheath : Hot deformation)	-	560	For each test
15.1 e) vi) (Sheath : Heat shock test)	-	560	For each test
15.1 e) vii) (Sheath : Thermalstability)	-	560	For each test
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	560	For each test
16.2(HIGH VOLTAGE TEST )	-	560	For each test
16.3(FLAMMABILITY TEST : Period of Burning )	-	560	For each test
16.3(FLAMMABILITY TEST : Unaffected length )	-	560	For each test
17.1(Manufacturer'. identification)	-	560	For each test
17.2(cable Indentification )	-	560	For each test
17.3(cable Code )	-	560	For each test

31 Jul, 2024

-
For category 01 only

IS 1065 : Part 1 (2019)

Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision)

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Description)	-	560	For each test.
5.2.1(Description)	-	560	For each test.
5.3 Table-1 i(Available chlorine)	-	560	For each test.
5.3 Table-1 ii(Stability, loss of Chlorine on the basis of initial available chlorine )	-	560	For each test.
5.3 Table-1 iiii(Moisture, percent by mass. )	-	560	For each test.
5.3 Table-1 iv(Particle size (Passing through 170 mm IS Sieve). Percent by mass)	-	560	For each test.
5.3 - Table 1 - Sl No - iv(Particle Size (passing through 1.70 mm IS Sieve) - Annex D)	-	560	For each test.
5.3 - Table 1 - Sl No - iii(Moisture - Annex C)	-	560	For each test.
5.3 - Table 1 - Sl No - ii(Stability, loss of chlorine on the basis of initial available chlorine - Annex B)	-	560	For each test.
5.3 - Table 1 - Sl No - i(Available Chlorine - Annex A)	-	560	For each test.
5.2, 5.2.1(Description)	-	560	For each test.

31 Jul, 2024

-
-

Bureau of Indian Standards

The National Standards Body of India

(Suspended) Quality Marking & Testing Laboratory, Indore

03, Pologround, Industrial Estate, Indore (M.P.), Indore, Indore, Madhya Pradesh, 452015

9425601159 contactqmtl@yahoo.in

Scope List