BIS - LIMS (Laboratory Information Management System)

Mbis Tescon Private Limited

DDA SHED NO. A-120, OKHLA INDUSTRIAL AREA, PHASE-2, New Delhi, South, Delhi, 110020

8799786535 info@mbistesconlabs.com

Scope List

Reset

9 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

All Variety

78000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1 Table 2(Mean outside diameter)	-	500	bis testing charges 78000 and for others 1.5 time of bis testing charges
6.3.2 Table 3(Wall thickness)	-	500	-
6.3.3 Fig 2(Length of pipe)	-	500	-
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	500	-
6.3.4.1(Wall thickness of sockets)	-	500	-
6.3.4.2(Fabricated fittings)	-	15000	-
6.3.4.3(Rotational moulded fittings)	-	15000	-
6.3.4.4(Type of fittings)	-	500	-
7.0(Physical characteristics of pipes)	-	0	-
7.1(Appearance)	-	500	-
7.2(Colour )	-	500	-
7.3(Vicat softening temperature of pipes)	-	1500	-
7.4(Resistance to Dichloromethane)	-	2000	-
7.5(longitudinal reversion)	-	1500	-
8.0(Physical characteristics of fittings)	-	0	-
8.1(Appearance and colour)	-	500	-
8.2(Vicat softening temperature of fittings)	-	1500	-
8.3(Effect of Heating (Stress Relief Test))	-	1500	-
9.0(Mechanical characteristics ofpipes)	-	0	-
9.1(Ring stiffness)	-	5000	-
9.2(Resistance to external blows at o C)	-	2000	-
9.3(Ring flexibility)	-	5000	-
9.4(Creep ratio)	-	30000	-
10.0(Mechanical Characteristics of fittings)	-	0	-
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	2000	-
11.0(Joints)	-	0	-
11.2(Solvent cement)	-	0	-
12.0(PERFORMANCE REQUIREMENTS)	-	0	-
12.1(Elastomeric Sealing Ring Joints)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	2000	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	2000	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	10000	-
12.2(Solvent cement joints)	-	0	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	2000	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	2000	-
7.6(7.6 Effect on Water)	-	5000	-
8.4(Effect on Water)	-	5000	-
5.0(Composition of the material)	-	0	-
5.1(Composition of the material)	-	10000	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	25000	-
5.3(Composition of the material)	-	0	-
5.4(Composition of the material)	-	0	-
6.0(DESIGNATION OF WALL CONSTRUCTIONS AND EXAMPLES OF TYPICAL JOINTING METHODS )	-	500	-
6.1(Wall Construction Designated as Type A)	-	500	-
6.2(Deswignation)	-	500	-
6.3(Dimensions of pipes and fittings)	-	0	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	0	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0	-
7.2(Physical characteristics for pipes and fittings )	-	0	-
7.3(Physical characteristics for pipes and fittings )	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
11.1(Marking General)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.1(Elastomeric Sealing Rings)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	0	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0	-
7.2(Physical characteristics for pipes and fittings )	-	0	-
7.3(Physical characteristics for pipes and fittings )	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.1(Marking General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-

11 Nov, 2028

-
Included w.e.f 28.11.2025

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

All Variety

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	500	for BIS branch 24000 pipe testing, 7000 raw material testing, 7000carbon black master batch testing and for others 1.5 times of BIS testing charges
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1000	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2000	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	1000	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	1000	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	500	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	1500	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	1000	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	1000	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	1000	-
5.2.1.1, T2(Compound ash content - Any Method)	-	1000	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	1500	-
5.3(Density of Higher olefin - IS 7328:2020)	-	500	-
5.3(Olefin Constituents- 14333-2022)	-	500	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	1500	-
5.3(Ash content- Any Method)	-	1000	-
5.3(Toluene extract - Any Method)	-	1000	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	1000	-
5.3(Carbon black particle size - Any Method)	-	1000	-
5.4(Antioxidant - Any Method)	-	3000	-
6(Pipe Description - IS 14333-2022)	-	100	-
6.2(Colour- IS 14333-2022)	-	100	-
7.1(Visual Appearance- IS 14333-2022)	-	100	-
7.2(Length- IS 14333-2022)	-	100	-
7.3(Coiling- IS 14333-2022)	-	1000	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	100	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	100	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	100	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	2000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	2000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	2000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	5000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	2000	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1000	-
8.3(Carbon black content- IS 2530-1963)	-	1000	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	1000	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1000	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2000	-
8.6(Density-IS 7328:2020)	-	500	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	2000	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1500	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1500	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	2000	-

11 Nov, 2028

-
Included w.e.f 17.11.2025

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

All Variety

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(COLOUR)	-	100	12000 Testing charges for BIS branch and for others 1.5 time of BIS testing charges
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	100	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	100	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	100	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	100	-
7.3.2(Rib height)	-	100	-
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	100	-
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	100	-
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	100	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	100	-
8.4(Sealing rings - Hardness)	-	500	-
9.5(Tensile Strength IS 12235(Part 13))	-	2000	-
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1500	-
4.1.2(K-Value as per IS-4669)	-	2000	-
9.3(Density IS 12235 (Part 14))	-	500	-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	-
9.2(Internal Diameter)	-	500	-
9.1( Visual Appearance)	-	100	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
CL 7.1,7.2(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	100	-
9.1(Visual Appearance)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	-
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	500	-
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	100	-
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	100	-
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	100	-
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	100	-
7.3.1(No.of Ribs)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	100	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	100	-
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	100	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	100	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	100	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	100	-
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	0	-
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	0	-
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	5000	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	1500	-
8.4(Width b)	-	100	-
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	500	-
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	500	-
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	5000	-
7.1(Screen Pipes)	-	500	-
11(Marking)	-	100	-
5.1(Materials)	-	100	-
8(Packing)	-	0	-
4.1.3(Cross Chain Length)	-	0	-
7.9(Case Depth)	-	0	-
8(Marking)	-	0	-
Cl 9.7(Effect on Water Lead (first extraction))	-	1000	-
Cl 9.7(Effect on Water Lead (third extraction))	-	1000	-
Cl 9.7(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	1000	-
Cl 9.7(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	1000	-
Cl 9.7(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	1000	-
5.0(Colour of Pipes)	-	100	-
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	1000	-
7.2(Link Twisted (Cross chain))	-	0	-
7.3(The Basic chains)	-	0	-

11 Nov, 2028

-
Included w.e.f 17.11.2025

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

All Variety

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions of pipe - i) Outside diameter)	-	200	for BIS branch office 24000 pipe testing, 8000 fittings testing, 7000 Raw material testing, 7000carbon black master batch testing and for others 1.5 times of BIS testing charges
5(Dimensions of pipe - ii) Wall thickness minimum)	-	200	-
6(Visual Appearance)	-	200	-
Cl.4.1.3(Den sity Test)	-	500	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	2000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1500	-
Cl.4.1.4(Carbon Black Content)	-	1500	-
Cl.6.2.4(Workmanship and Appearance)	-	200	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-
Cl.7.1.l(Visual Anneara nce)	-	200	-
Cl.7.1.2(Hydraulic Characteristic)	-	4000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1500	-
Cl.7.1.4(Elongation)	-	1500	-
Cl.7.1.5(Fusion Compatibility)	-	4000	-
Cl.7.1.6(Corrected Density)	-	1500	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1500	-
Cl.7.2.2(Cl.7.2.2)	-	2000	-
Cl.7.2.3(Weld ability Test)	-	4000	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	1000	-
8(Supply of pipe (Visual))	-	200	-
4.1.3, Table 1,(i)(Bass density)	-	500	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1000	-
4.1.3, Table 1,(iii)(Thermal stability)	-	2000	-
4.1.3, Table 1,(iv)(Volatile matter)	-	1000	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1500	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	1500	-
4.1.4(The Carbon Content and Dispersion)	-	1500	-
4.1.5(Carbon Black Specification)	-	1500	-
4.1.6(Antioxidant)	-	3000	-
5.1, Table 1,(ii)(90° Bends and tee)	-	8000	-
5.1, Table 1,(iv)(PCN)	-	8000	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	8000	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	8000	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	8000	-
7.3(Quick Couple Fitting)	-	500	-
5.1.2(Squareness)	-	200	-
7.1(Hydraulic Characteristics - Quality test)	-	2500	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1500	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Test- i) Tensile Strength)	-	0	-
7.3(Tensile Test - ii)Elongation at Break)	-	0	-
7.4(Fusion Compatibility Test- a) Quality test)	-	0	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	0	-
7.5(Density)	-	0	-
7.6(Melt Flow Rate)	-	0	-
7.6(Melt Flow Rate)	-	0	-
4.2(Carbon black- a)carbon content)	-	0	-
4.2(Carbon black- b) Dispersion of carbon black)	-	0	-
7.6(Melt now Rate (MFR))	-	0	-
7.5(Density)	-	0	-
7.4 Table-2(Fusion Compatibility Test)	-	0	-
7.3(Tensile Test)	-	0	-
7.2(Reversion Test)	-	0	-
6.1(VISUAL APPEARANCE)	-	0	-
5.1.2(Ovality)	-	0	-
5.1 table -1(DIMENSIONS OF PIPES)	-	0	-
4.3(Anti-oxidant)	-	0	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	0	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	0	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	0	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	0	-
3(CLASSIFICATION OF PIPES)	-	0	-
4.1(Quick Coupled Male and Female Couplers)	-	0	-
4.1(Quick Coupled Male and Female Couplers)	-	0	-
4.1.3(Workmanship and appearance)	-	0	-
4.1.4(Holding attachments for coupler parts)	-	0	-
6.1.3(Weldability Test- b) Acceptance test)	-	0	-
3(Quick Coupled pipes)	-	0	-
3(QUICK COUPLED PIPES)	-	0	-
4(QUICK COUPLED FITTINGS)	-	0	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	0	-
4.1 (b)(HDPE couplers —)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	0	-
4.1 .1.2.1(HDPE couplers)	-	0	-
4.1 .1.2.2(HDPE couplers)	-	0	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	0	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	0	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	0	0
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	0	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	0	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	0	0
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	0	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	0	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	0	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	0	-
6.1(Quick Coupled Pipes and Fittings)	-	0	-
6.1.1, 6.1.1.1(Leakage Test)	-	0	-
6.1.1, 6.1.1.1(Leakage Test)	-	0	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	0	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.3, 6.1.3.1(Weldability Test)	-	0	-
6.1.3.1.1(Weldability Test)	-	0	-
6.1.3.2(Quick coupled fittings)	-	0	-
6.2, 6.2.1(Quick Coupled Fittings)	-	0	-
7.2.1(Visual and Workmanship Requirement)	-	0	-
6.2 b(Material Identification - Male & Female Coupler)	-	0	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.4()	-	0	-
6.3.5(Material Identification - Saddle)	-	0	-
6.3.5(Material Identification - Pipe Ends)	-	0	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	0	-
4.2(Metallic Couplers)	-	0	-
4.2(Metallic Couplers)	-	0	-
7.2.1(Leakage Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(Thermal Stabi lity)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	100	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.5(Di men sion)	-	0	-
Cl.5.1.l(Outside Diameter)	-	0	-
Cl.5.1.l(Outside Diameter)	-	0	-
Cl.6.2.L(Wall Thickness)	-	0	-
Cl.6.2.6(Ageing Test)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.3(Reversion Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Elongation)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	0
Cl.7.2.3(Weld ability Test)	-	0	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	0	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	0	-
6.1(Thermal Stability (OIT))	-	0	-
6.1(Volatile Matter)	-	0	-
6.1(Water content)	-	0	-
6.1(Tensile strength at Yield & Elongation at break)	-	0	-
6.1(Carbon Black Content)	-	0	-
6.1(Carbon Black Dispersion)	-	0	-
6.2.1(Base Density x 2)	-	0	-
6.2.1(Melt Flow Index x 2)	-	0	-
6.2.1(Thermal Stability (OIT) x 2)	-	0	-
6.2.1(Volatile Matter x 2)	-	0	-
6.2.1(Water content x 2)	-	0	-
6.2.1(Carbon Black Content x 2)	-	0	-
6.2.1(Carbon Black Dispersion x 2)	-	0	-
6.2.1(Wall thickness of male & female coupler)	-	0	-
6.2.4(Workmanship and appearance (Visual))	-	0	-
6.2.5(Holding attachment for coupler parts)	-	0	-
6.2.5(Material Composition (Chemical Analysis))	-	0	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	0	-
6.2.6(Material Identification (Chemical Analysis))	-	0	-
6.2.6(Color)	-	0	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	0	-
6.2.6(Ageing Charges for rubber ring)	-	0	0
7.1.1(Visual appearance of pipes)	-	0	-
7.1.2(Hydraulic Characteristics)	-	0	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
7.1.3(Reversion)	-	0	-
7.1.4(Tensile strength & elongation)	-	0	-
7.1.5(Fusion Compatibility test)	-	0	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
7.1.6(Corrected Density)	-	0	-
7.1.6(Base Density)	-	0	-
7.1.6(Carbon black Content)	-	0	-
7.1.7(Melt Flow Rate (MFR))	-	0	-
7.2.1(Leakage test 1hour / 27°C)	-	0	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	0	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
4.1.1 (Table-1)(Density)	-	0	-
4.1.1 (Table-1)(Melt Flow Index)	-	0	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	0	-
4.1.1 (Table-1)(Volatile Matter)	-	0	-
4.1.1 (Table-1)(Water content)	-	0	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	0	-
4.1.4(Carbon Black Content)	-	0	-
4.1.4(Carbon Black Dispersion)	-	0	-
4.1.1(Polyethylene material)	-	0	-
4.1.7(Rework Material)	-	0	-
4.2(Metallic Couplers)	-	0	-
5.1, Table 1,(i)(Plain pipes)	-	0	-
5.1, Table 1,(iii)(Base pipe )	-	0	-
7.1.1(Visual Appearance and Workmanship)	-	0	-
7.1.2(Hydraulic Performance Characteristic)	-	0	-
7.1.3(Reversion Test)	-	0	-
7.1.4(Tensile Test)	-	0	-
7.1.5(Fusion Compatibility Test)	-	0	-
7.1.6(Corrected Density)	-	0	-
7.1.7(Melt flow rate)	-	0	-
7.2.1(Leakage Test)	-	0	-
7.2.2(Hydraulic Proof Test)	-	0	-
7.2.3(Weldability Test)	-	0	-
10(Marking)	-	0	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	0	-
7.1 Table -2(Hydraulic Characteristics)	-	0	-
4.1.3, Table 1,(v)(Water content)	-	0	-
6.1.3(Weldability Test- a) Quality test)	-	0	-

11 Nov, 2028

-
Included w.e.f 17.11.2025

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

ALL VARIETY

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.2(Fittings)	-	100	10000 Testing charges for BIS branch office and for others 1.5 time of BIS testing charges
6.3(General)	-	100	-
6.3(General)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	1000	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	1000	-
8.2.2(Regulated Emitting Pipes)	-	1000	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	100	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	500	-
8.3.3(Flow Paths in Emitting Unit)	-	500	-
8.3.4(Spacing ofEmitter Units)	-	500	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1000	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	1000	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1500	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	2000	-
8.8(Determination of Emitting Unit Exponent)	-	100	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	0	-
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	5000	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	0	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	1000	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	1000	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0	-
4.2(Carbon black content)	-	0	-
4.2(Carbon black dispersion)	-	0	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	0	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0	-
6.2(Fittings)	-	0	-
6.3(General)	-	0	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-

11 Nov, 2028

-
included w.e.f 17.11.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

ALL VARIETY

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	100	1000 Testing charges for BIS branch office and for others 1.5 time of BIS testing charges
Cl-6.0(Visual Appearance)	-	100	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	2000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1500	-
Cl-7.2(Reversion Test)	-	1000	-
Cl-7.3(Tensile Test)	-	2000	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1000	-
Cl-8.0(Supply of pipes)	-	100	-
Cl-9.0(Coiling)	-	100	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
Cl-4.1(Material)	-	5000	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	1000	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	1000	-

11 Nov, 2028

-
Included w.e.f 13.11.2025

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

ALL VARIETY

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	100	16000 Testing charges for BIS branch office and for others 1.5 time of BIS testing charges
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	3000	-
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	100	-
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	100	-
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	100	-
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	100	-
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	100	-
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	100	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	100	-
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1000	-
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	1000	-
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1000	-
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	2000	-
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	1000	-
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1000	-
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1000	-
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	1000	-
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	2000	-
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	2000	-
8.6(Effect on Water Test)	-	3000	-
14(Marking)	-	100	-
Cl 8.6(Effect on Water Lead (first extraction))	-	100	-
Cl 8.6(Effect on Water Lead (first extraction))	-	0	-
Cl 8.6(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 8.6(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 7.3(Socket length (Take 4 reading & minimum will be reported))	-	100	-
CL 7.3.1(Socket wall Thickness For S2 and S3 (Take 4 reading and average will be reported))	-	100	-
CL 7.3.2 grooved sockets(Inside diameter of Sockets, D1 (Take 4 reading & minimum, Maximum will be reported))	-	100	-
CL 7.3.2 grooved sockets(Inside diameter of beading D2 (Take 4 reading & minimum, Maximum will be reported))	-	100	-
CL 7.3.2 grooved sockets(Length of beading and Neck A (Take 4 reading & Maximum will be reported))	-	100	-
CL 7.3.2 grooved sockets(Neck of Socket B (Take 4 reading & minimum, will be reported))	-	100	-
CL 7.3.2 grooved sockets(Length beyond beading C (Take 4 reading & minimum will be reported))	-	100	-
Cl 8.6(Effect on Water Lead (third extraction))	-	0	-
Cl 8.6(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-

11 Nov, 2028

-
Included w.e.f 13.11.2025

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

All Variety

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	100	16000 TESTING CHARGES FOR BIS BRANCH OFFICE AND FOR OTHERS 1.5 TIMES OF BIS TESTING CHARGES
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	100	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	100	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	100	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	100	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	100	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	100	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	100	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	100	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	100	-
5(CLASSIFICATION OF PIPES)	-	100	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	100	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	100	-
7.2.1(DIMENSIONS-Socket)	-	100	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	100	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	100	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	100	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	100	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	100	-
8(SEALING RINGS)	-	500	-
9.1(PIPE ENDS)	-	100	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	100	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	100	-
10.1(Colour)	-	100	-
10.1(Surface Finish)	-	100	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	1000	-
10.3(Effect on Water Test)	-	5000	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1000	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1000	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	1000	-
10.7(Sulphated Ash Content)	-	1000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	4000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	4000	-
11.2(Resistance to External Blows at 0°C)	-	2000	-
13.1(Marking)	-	100	-
6.1.2(PVC Resin)	-	3000	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	100	-
7.1.4(Length)	-	100	-
6.1.1(VCM Content)	-	4000	-
7.2.1.2b(Maximum inner diameter of groove)	-	100	-
cL-13.1.1(Marking)	-	100	-
Cl-13.1.2(Marking)	-	100	-
Cl-10.3 (i)(Effect on Lead (first extraction))	-	0	-
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	0	-
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
Cl-10.3 (iv)(Effect on Cadmium)	-	0	-
Cl-10.3 (v)(Effect on Mercury)	-	0	-
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	0	-
Cl-7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	0	-
CL 7.1(Wall thickness "Average,minimum,maximum" (Take 8 reading))	-	100	-

11 Nov, 2028

-
Included w.e.f 13.11.2025

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

All Verities

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	2000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.9 table-6(Elongation at Break)	-	2000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.8(Tensile Strength for Butt-fusion)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.7(Density)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.5 (Oxidation Induction Time)	-	2000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.4( Melt Flow Rate)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.2(Longitudinal Reversion Test)	-	1500	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	4000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	2000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
7.4.1.2(Ovality)	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
7.2(Length)	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6.2.1(6.1.1 Identification Stripes)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6.2(Colour)	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6.1.4(PIPE DESCRIPTION)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6.1.3 (PIPE DESCRIPTION)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6, 6.1.2(PIPE DESCRIPTION)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6, 6.1.1(PIPE DESCRIPTION)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
6, 6.1(PIPE DESCRIPTION)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.6(Overall migration)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.3(Carbon black)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.4(Anti oxydent)	-	3000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3 (a)(Carbon Black Master Batch)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3(b)(Carbon Black Master Batch)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3(c)(Carbon Black Master Batch)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3(e)(Carbon Black Master Batch)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5, 5.1 table-1(MATERIALS)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
7()	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.2(Density)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.2(MFI @ 1900C/5.0 Kg)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.2(Volatile matter Content)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3(Toluene Extract)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 7.1(Visual Apperance)	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 7.3(Coiling)	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 8.3(Carbon Black content)	-	1500	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 8.3(Carbon Black Dispersion)	-	1500	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 8.6(Overall migration (stimulate))	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Clause 8.6(Overall migration (surface of material))	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
7.1(Visual Appearance)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
7.3(Coiling)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	2500	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Cl. 8.3(Carbon Black Content)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Cl. 8.3(Carbon Black Dispersion)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.7(Density-IS 7328:2020)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.7(Corrected Density- IS 7328:2020)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	2000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Cl 8.3(Carbon Black Content)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
Cl 8.3(Carbon Black Dispersion)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
CL 7.4(Wall Thickness (Take 8 reading & Minimum and Maximum reported))	-	100	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.2(Polyethylene Resin)	-	0	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges
5.3(d)(Carbon Black Master Batch)	-	1000	For BIS branch testing charges 24000 and for others 1.5 time of BIS testing charges

11 Nov, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Mbis Tescon Private Limited

DDA SHED NO. A-120, OKHLA INDUSTRIAL AREA, PHASE-2, New Delhi, South, Delhi, 110020

8799786535 info@mbistesconlabs.com

Scope List