BIS - LIMS (Laboratory Information Management System)

ELECTRONICS AND QUALITY DEVELOPMENT CENTRE

B 177/178 & B/23/2, GIDC ELECTRONICS ESTATE, SECTOR 25, Gandhinagar, Gandhinagar, Gujarat, 382024

9427418080 qm@eqdc.in

Scope List

Reset

6 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12615 (2018)

Line operated three phase AC motors (IE Code) "Efficiency classes and performance specification" (Third Revision)

Rotating electrical machines

375000 View breakup
Rs.6,825/- From 0.37 to 5.5kW, Rs.8,550/- From 5.5 to 11kW, Rs.12,488/- From 11 to 19kW, Rs.15,413/- From 19 to 22 kW, Rs.16,463/- From 22 to 29.5kW, Rs.17,963/- From 29.5 to 33kW, Rs.18,788/- From 33 to 45kW, Rs.24,338/- From 45 to 75kW, Rs.33,600/- From 75 to 110kW, Rs.1,50,000/- From 110.1 to 200kW, Rs.1,87,500/- From 200.1 to 250kW, Rs.2,25,000/- From 250.1 to 300kW, Rs.3,00,000/- From 300.1 to 350kW, Rs.3,75,000/- From 350.1 to 375kW

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2.1(Dimensions)	-	18500	From 350.1 to 375 kW
11.0(DUTY AND RATING)	-	6500	From 350.1 to 375 kW
8.0(Earthing)	-	6500	From 350.1 to 375 kW
16.2.3(Full Load Test to Determine Efficiency, Power Factor and Slip)	-	62500	From 350.1 to 375 kW
16.1.6(High Voltage Test)	-	23500	From 350.1 to 375 kW
16.1.1(Insulation Resistance Test)	-	23500	From 350.1 to 375 kW
16.1.4(Locked Rotor Readings of Voltage, Current and Power Input at a Suitable Reduced Voltage)	-	57500	From 350.1 to 375 kW
16.2.2(Locked Rotor Test)	-	57500	From 350.1 to 375 kW
16.2.2.1(Locked Rotor Test)	-	57500	From 350.1 to 375 kW
16.2.2.2(Locked Rotor Test)	-	57500	From 350.1 to 375 kW
16.2.2.2.1(Locked Rotor Test)	-	57500	From 350.1 to 375 kW
16.2.2.3(Determination of starting characteristics -locked rotor current)	-	57500	From 350.1 to 375 kW
16.2.2.3.1(Direct proportion method)	-	57500	From 350.1 to 375 kW
Cl. 18.2(Marking and labelling)	-	6500	From 350.1 to 375 kW
15.2(Rating)	-	6500	From 350.1 to 375 kW
15.3.2(Marking)	-	6500	From 350.1 to 375 kW
Cl. 18.1(Marking and labelling)	-	6500	From 350.1 to 375 kW
16.1.2(Measurement of Resistance of Windings of Stator)	-	40000	From 350.1 to 375 kW
16.2.1(Dimensions)	-	18500	From 350.1 to 375 kW
16.2.5(Momentary Overload Test)	-	47500	From 350.1 to 375 kW
16.1.3(No Load Test)	-	40000	From 350.1 to 375 kW
16.1.3(No Load Test)	-	40000	From 350.1 to 375 kW
12.2(Pull up torque)	-	57500	From 350.1 to 375 kW
16.1.5(5 Reduced Voltage Running up Test at no-load (for squirrel cage motor up to 37 kW only))	-	40000	From 350.1 to 375 kW
16.2.4(Temperature Rise Test)	-	127500	From 350.1 to 375 kW
16.2.4(Temperature Rise Test)	-	127500	From 350.1 to 375 kW
9.0(Terminal Marking)	-	6500	From 350.1 to 375 kW
6(Method of cooling)	-	127500	From 350.1 to 375 kW
18.3(Marking)	-	6500	From 350.1 to 375 kW
18.3(BIS Certification Marking )	-	6500	From 350.1 to 375 kW

Complete

09 Oct, 2024

-
Capacity: 0.37 kW to 375 kW. Exclusions: Optional tests: Test for vibration severity of motor (Cl.16.3.1), Test for noise levels of motor (Cl.16.3.2), Test for degree of protection by enclosure (Cl.16.3.3), Over speed test (Cl.16.3.4), Temperature rise test at limiting values of voltage and frequency variation (Cl.16.3.5).

IS 9283 (2013)

Motors for submersible pumpsets - Specification (Second Revision)

Motors for Submersible Pumpsets - Up to 45 kW

12500 View breakup
Up to 3.7kW : Rs. 3,750/-; Above 3.7kW up to 7.5kW : Rs. 4,312.5/-; Above7.5kW up to 11kW : Rs. 4,875/- ; Above 11kW up to 15kW : Rs. 5,250/-; Above 15kW up to 20kW : Rs. 5,625/-; Above 20kW up to 25kW : Rs. 6,187.5/-; Above 25kW up to 30kW : Rs. 6,750/-; Above 30kW up to 35kW : Rs. 7,312.5/- ; Above 35kW up to 40kW : Rs.7,875/-; Above 40kW up to 45k : Rs. 8,250/-.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Construction, IS 9283)	-	100	-
5.1.1(Construction, IS 9283)	-	100	-
5.1.2(Construction, IS 9283)	-	100	-
5.1.3(Construction, IS 9283)	-	100	-
5.1.4(Construction, IS 9283)	-	100	-
5.2.1(Earthing, IS 9283)	-	100	-
5.2.2(Earthing, IS 9283)	-	100	-
5.2.3(Earthing, IS 9283)	-	100	-
5.2.4(Earthing, IS 9283)	-	100	-
5.2.5(Earthing, IS 9283)	-	100	-
5.3(Foreign Matter, IS 9283)	-	100	-
5.5(Finish of Bearings, IS 9283)	-	300	-
5.6(Balancing of Rotor, IS 9283)	-	600	-
7.1(Dimensions of Motors, IS 9283)	-	500	-
7.2.1(Tolerances, IS 9283)	-	500	-
7.2.2(Tolerances, IS 9283)	-	500	-
13(Terminal Markings, IS 9283)	-	100	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
15.1(Marking, IS 9283)	-	50	-
17.1(Performance values, IS 9283)	-	500	-
17.1(Performance values, IS 9283)	-	500	-
17.1(Performance values, IS 9283)	-	500	-
17.1(Performance values, IS 9283)	-	500	-
18.1(Overload test, IS 9283)	-	500	-
19(Temperature rise test, IS 9283)	-	1200	-
19(Temperature rise test, IS 9283)	-	1000	-
20(High Voltage test, IS 9283)	-	400	-
21(Insulation Resistance test, IS 9283)	-	200	-
23(Leakage Current test, IS 9283)	-	700	-
22(Speed, IS 9283)	-	500	-
8(Type of duty, IS 9283)	-	100	-

Complete

09 Oct, 2024

-
Upto 45kW

IS 8034 (2018)

Submersible pumpsets - Specification (Third Revision)

Submersible Pump-sets Up to 45 kW

12500 View breakup
Up to 3.7kW : Rs. 4,125/-; Above 3.7kW up to 7.5kW : Rs. 4,500/-; Above7.5kW up to 11kW : Rs. 4,875/- ; Above 11kW up to 15kW : Rs. 6,000/-; Above 15kW up to 20kW : Rs. 6,375/-; Above 20kW up to 25kW : Rs. 8,250/-; Above 25kW up to 30kW : Rs. 9,000/-; Above 30kW up to 35kW : Rs. 9375/- ; Above 35kW up to 40kW : Rs.9,750/-; Above 40kW up to 45k : Rs. 10,500/-.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
14(Marking)	-	50	-
6.1 (a)(Constructional Features)	-	100	-
6.1 (b)(Constructional Features)	-	100	-
6.1 (c)(Constructional Features)	-	100	-
6.1 (d)(Constructional Features)	-	100	-
6.1 (e)(Constructional Features)	-	100	-
6.1 (f)(Constructional Features)	-	100	-
6.2 (a)(Material of construction Part Sub Assembly Shaft Sleeve)	-	100	-
6.2 (b)(Material of construction Part Sub Assembly Casing wear ring (if provided))	-	100	-
6.2 (c)(Material of construction Part Sub Assembly Bush)	-	100	-
6.2 (d)(Material of construction Part Sub Assembly Discharge casing (if provided))	-	100	-
6.2 (e)(Material of construction Part Sub Assembly Impeller)	-	100	-
6.2 (f)(Material of construction Part Sub Assembly Pump Bowl/Diffuser)	-	100	-
6.2 (g)(Material of construction Part Sub Assembly Pump Shaft)	-	100	-
6.2 (h)(Material of construction Part Sub Assembly Suction Casing)	-	100	-
6.2.2.1(Gaskets, Seals and Packings)	-	100	-
6.2.2.2(Gaskets, Seals and Packings)	-	100	-
6.2.3(Gaskets, Seals and Packings)	-	100	-
6.2.4(Gaskets, Seals and Packings)	-	100	-
6.2.5(Gaskets, Seals and Packings)	-	100	-
7.1.1(Design features: Typical design features 0f components of pump)	-	100	-
7.1.2(Design features: Typical design features 0f components of pump)	-	100	-
7.1.3(Design features: Typical design features 0f components of pump)	-	100	-
7.1.4(Design features: Typical design features 0f components of pump)	-	100	-
7.1.5(Design features: Typical design features 0f components of pump)	-	100	-
7.1.6(Design features: Typical design features 0f components of pump)	-	100	-
8.1(General Requirements)	-	100	-
8.2(Casing)	-	500	-
8.3(Impeller)	-	100	-
8.4.1(Shaft)	-	100	-
8.4.2(Shaft)	-	100	-
8.5.1(Balancing)	-	600	-
8.5.2(Balancing)	-	600	-
8.7.1(Direction of Rotation)	-	100	-
8.7.2(Direction of Rotation)	-	100	-
8.8(Terminal Marking)	-	0	-
8.9.1(Typical Installation)	-	100	-
8.9.3(Typical Installation)	-	100	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1200	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1500	-
10.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	1500	-
10.3(Hydrostatic Pressure Test)	-	500	-
11.1.1(Guarantee of Performance)	-	500	-
11.1.2(Guarantee of Performance)	-	500	-
11.1.2(Guarantee of Performance)	-	500	-
11.1.3(Guarantee of Performance)	-	500	-
11.1.4(Guarantee of Performance)	-	500	-
11.1.5(Guarantee of Performance)	-	500	-
12(Guarantee of workmanship and material)	-	100	-
8.9(Typical installation)	-	100	-
8.5(Balancing of rotor)	-	600	-
8.6(Submersible cable)	-	200	-
8.7(Direction of Rotation)	-	100	-
7(Design features)	-	100	-
7.1.10(Voltage & Frequency variation)	-	100	-
6(Constructional Features)	-	100	-
6(Measurement of shaft extension)	-	100	-
11(Guarantee of Performance)	-	100	-
10(Pump Performance test)	-	1500	-
9.1(General)	-	100	-
9.10 (a)(Insulation Resistance test)	-	200	-
9.10 (b)(High Voltage test)	-	400	-
9.10 (c)(Measurement of Stator Resistance)	-	400	-
9.10 (d)(No Load Test at Rated Voltage)	-	500	-
9.10 (e)(Reduced voltage Running up test)	-	500	-
9.10 (f) & (g)(Locked Rotor Test)	-	700	-
9.10 (h)(Leakage current test)	-	300	-
9.10 (j)(Temperature Rise Test at Rated Voltage)	-	1200	-
9.10 (k)(Temperature rise test at reduced voltage)	-	1000	-
8.9.4c(Earthing)	-	100	-
7.1.7(Pump loading shall be as per 11.1.5)	-	100	-
7.1.9(prime mover electric motor suitable for the pumps shall be of contineous duty as specified in IS/IEC 60034-4 and as per IS 9283)	-	100	-
8.6.1(Flat/Round cables as per IS694 shall be used)	-	100	-
8.6.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	100	-
8.6.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	100	-
8.6.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	100	-
8.9(Installation)	-	100	-
8.9.2(The pumpset shall be installed as per guidelines laid down in IS 14536 or as per the recommendation of the manufacturer)	-	100	-
8.9.4.1(Earthing of the motor shall be done as per IS 9283 in accordance with the relevant provisions of IS 3043.)	-	100	-
8.9.4.2(In case of PVC pipes used as discharge pipe, a separate non corrosive, low resistance conductor from motor earth terminal to control panel earth terminal shall be provided for earthing.)	-	100	-
8.9.4.3(In case non corrosive GI pipes and clamps are used for the purpose of earthing the motor, earthing connection may be made to the discharge pipe clamp and to the control panel earth terminal)	-	100	-

Complete

09 Oct, 2024

-
Upto 45kW. REVISED VERSION OF IS 8034:2018 Included w.e.f. 05 Apr 2019.

IS 14220 (2018)

Openwell submersible pumpsets - Specification (First Revision)

Open-well Submersible Pump-sets - Up to 45 kW

12500 View breakup
Up to 3.7kW : Rs. 3,750/-; Above 3.7kW up to 7.5kW : Rs. 4,500/-; Above7.5kW up to 11kW : Rs. 4,875/- ; Above 11kW up to 15kW : Rs. 5,250/-; Above 15kW up to 20kW : Rs. 5,625/-; Above 20kW up to 25kW : Rs. 6,000/-; Above 25kW up to 30kW : Rs. 6,375/-; Above 30kW up to 35kW : Rs. 6,750/- ; Above 35kW up to 40kW : Rs.7,125/-; Above 40kW up to 45k : Rs. 7,500/-.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Design Features)	-	100	-
8.1.1(Design Features)	-	100	-
8.1.4(Design Features)	-	100	-
8.1.5(Design Features)	-	100	-
8.1.5(Design Features)	-	100	-
8.1.7(Design Features)	-	100	-
9(Efficiency)	-	300	-
10(Performance (Cl 17.1 of IS 5120))	-	1500	-
10(Suction and Delivery Ends (Cl 17.2 of IS 5120))	-	100	-
10(Suction and Delivery Ends (Cl 17.2.1 of IS 5120))	-	100	-
10(Fluid Passages (Cl 17.3 of IS 5120))	-	100	-
10(Draining Plugrs (Cl 17.4 of IS 5120))	-	100	-
10(Lantern Ring (Cl 17.5 of IS 5120))	-	100	-
10(Casing (Cl 17.6 of IS 5120))	-	100	-
10(Impeller (Cl 17.7 of IS 5120))	-	400	-
10(Shaft (Cl 17.8 of IS 5120))	-	100	-
10(Shaft Couplings (Cl 17.9 of IS 5120))	-	100	-
10(Bearings (Cl 17.10 of IS 5120))	-	100	-
10(Bearings (Cl 17.10.1 of IS 5120))	-	100	-
10(Bearings (Cl 17.10.2 of IS 5120))	-	100	-
10( Stuffing Boxes (Cl 17.11 of IS 5120))	-	100	-
10(Base Plates (Cl 17.12 of IS 5120))	-	100	-
10(Prime Mover (Cl 17.13 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14 of IS 5120))	-	100	-
10(Name Plate (Cl 17.14.1 of IS 5120))	-	100	-
10.2(Casing)	-	300	-
10.3(Impeller)	-	100	-
10.4.1(Shaft)	-	100	-
10.4.2(Shaft)	-	100	-
10.5.1(Balancing)	-	600	-
10.5.2(Balancing)	-	600	-
10.5.3(Balancing)	-	600	-
10.5.4(Balancing)	-	600	-
10.6.1( Provision for Earthing)	-	100	-
10.6.2( Provision for Earthing)	-	100	-
10.6.3( Provision for Earthing)	-	100	-
10.6.4( Provision for Earthing)	-	100	-
10.7.1(Terminal Marking and Direction of Rotation)	-	100	-
10.7.2(Terminal Marking and Direction of Rotation)	-	100	-
10.7.3(Terminal Marking and Direction of Rotation)	-	100	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Rate of flow and head Cl.8 of IS 11346-2002)	-	1200	-
15.2(Laboratory Tests Cl.8 of IS 11346-2002 Efficiency Cl.8.3 of IS 11346-2002)	-	1200	-
15.5(Hydrostatic Pressure Test)	-	500	-
16.1.1( Guarantee of Performance)	-	500	-
16.1.2( Guarantee of Performance)	-	500	-
16.1.3( Guarantee of Performance)	-	500	-
16.1.4( Guarantee of Performance)	-	500	-
16.1.5( Guarantee of Performance)	-	500	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1(Marking)	-	50	-
18.1.3(Marking)	-	50	-
7(Constructional features)	-	100	-
7.1(It is recognized that a number of materials of construction are available to meet the needs for pumps handling clear, cold water.)	-	100	-
7.2(Gaskets, seals and packings used for clear, cold water pumps shall conform to the applicable requirements specified in 5.2 of IS 5120.)	-	100	-
7.3(The motor shall be provided with a breathing attachment like bellows, diaphragm etc; to compensate the volumetric variation of water inside the motor due to change in the temperature.)	-	100	-
7.4(The motor shall be protected from ingress of well water, sand and other foreign matter by means of cable glands, rubber seals etc.)	-	100	-
7.5(All materials and components for the motor shall be suitable for application in respect of resistance and mechanical performance to protect it)	-	100	-
7.6(The rotor of the wet type open well submersible motor and rotor in water filled designed motor shall be provided with suitable coating from corrosion under water. However if suitable anticorrosion additive is added in the water, no separate protection on rotors is necessary.)	-	100	-
8(Design Features)	-	100	-
8.1.2(The multi-stage pump shaft may be guided through bearings, the bearings may be provided in stage casing, suction housing and discharge casing, while in case of intermediate bearings, suitable positions may be selected in the overall span.)	-	100	-
8.1.3(The pump may be equipped with replaceable bearing and wearing ring, wherever provided.)	-	100	-
8.1.4(The strainer on the suction shall offer the best compromise amongst restraining large solids from entering the pump and containing the suction losses to the minimum.)	-	100	-
8.1.5(The pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +5 percent and minimum –15 percent of the guaranteed duty point head up to 30 m. Above 30 m, the pump shall be capable to give discharge without overloading the prime mover within the permissible current at rated voltage and supply frequency at minimum +10 percent and minimum –25 percent of the guaranteed duty point head.)	-	100	-
12(Cable)	-	100	-
12.1.2(The size of the conductor shall be adequate and suitable for contineous use under water and in air. the length of the cable shall be minimum 2 m externallly unless otherwise specified by the customer)	-	100	-
12.1.3(The size and of the cable should be suitably selected so that the voltage drop between control panel and the mptor terminal does not exeed three percent of the rated voltage)	-	100	-
12.1.4(In case a joint is required to be made between the lead cable supplied with the motor and the user’s cable, a detailed procedure to make water tight joining shall be supplied by the motor manufacturer.)	-	100	-
12.1.5(If four core cable is used, the fourth core is to be used for earthing.)	-	100	-
14.10.1(Type test)	-	500	-
14.10.1(a)(Insulation Resistance test)	-	200	-
14.10.1(b)(High Voltage test)	-	400	-
14.10.1(c)(Measurement of stator resistance)	-	400	-
14.10.1(d)(No load test at rated voltage)	-	500	-
14.10.1(e)(Reduced voltage running up test at no load)	-	500	-
14.10.1(f)(Locked rotor)	-	700	-
14.10.1(g)(Breakaway (starting) torque)	-	700	-
14.10.1(h)(Leakage current test;)	-	300	-
14.10.1(j)(Temperature rise test at rated voltage)	-	1200	-
14.10.1(k)(Temperature rise test at reduced voltage)	-	1000	-
16.1(Guarntee of Performance)	-	100	-
16.1.1(The pumpset shall be guaranteed for their performance of the nominal volume rate of flow and the nominal head at the guaranteed duty point. The overall efficiency of the pumpset shall be guaranteed at the declared duty point only.)	-	100	-
16.1.2(The guarantee shall be deemed to have been met with, if the measured values of head, volume rate of flow and overall efficiency are within the indicated in IS 11346 limits)	-	100	-
16.1.3(Open well submersible motor shall not get overloaded in the specified operating head range at rated voltage and supply frequency.)	-	100	-
16.1.4(The pump shall be tested for the operating head range as per 8.1.5.)	-	100	-
16.1.5(The overloading of motor is that condition when maximum current drawn by the motor exceeds the limit of 1.07 times of the rated motor current)	-	100	-
16.1.6(The tolerance shall apply to guaranteed duty point only.)	-	100	-
16.1.7(Performance at rated voltage and supply frequency is actual performance of the set. This is better than performance at rated speed, since in the entire operating head range speed of motor is higher than rated speed, as motor is running in under loaded condition.)	-	100	-
16.1.8(The manufacturer shall specify the minimum submergence of pump unit at duty point.)	-	100	-

Complete

09 Oct, 2024

-
Upto 45kW. REVISED VERSION OF IS 14220:2018 Included w.e.f. 05 Apr 2019.

IS 17018 : Part 1 (2018)

Solar photovoltaic water pumping systems: Part 1 centrifugal pumps - Specification

33750 View breakup
Rs.16500/- for 1hp, Rs.18750, for 2hp, Rs.20250/- for 3hp, Rs.22500/- for 4hp, Rs.26250/- for 5hp, Rs.33750/- for above 5hp to 7hp, Rs. 37500 for above 7hp to 10hp.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1(Electrical performance Test- Speed)	-	5000		-
10.3(Whole day Performance (real condition testing))	-	31500		-

Complete

09 Oct, 2024

-
Included w.e.f. 09-09-2020. Up to 5 HP

IS 13779 (1999)

AC static watihour meters, class 1 and 2 - Specification (First Revision)

975 View breakup
Type Tests : Rs. 1,05,000/- (For Single Phase and Three Phase); Acceptance Tests : Rs. 14,250/- (For Single Phase and Three Phase); Routine Tests : Rs. 8,625/- (For Single Phase and Three Phase).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 a)(MARKING OF METERS : Name Plate )	-	75	-
7.1 b)(MARKING OF METERS : Name Plate )	-	75	-
7.1 c)(MARKING OF METERS : Name Plate )	-	75	-
7.1 d)(MARKING OF METERS : Name Plate )	-	75	-
7.1 e)(MARKING OF METERS : Name Plate )	-	75	-
7.1 f)(MARKING OF METERS : Name Plate )	-	75	-
7.1 g)(MARKING OF METERS : Name Plate )	-	75	-
7.1 h)(MARKING OF METERS : Name Plate )	-	75	-
7.1 j)(MARKING OF METERS : Name Plate )	-	75	-
7.1 k)(MARKING OF METERS : Name Plate )	-	75	-
7.1 m)(MARKING OF METERS : Name Plate )	-	75	-
7.1 p)(MARKING OF METERS : Name Plate )	-	75	-
7.1 n)(MARKING OF METERS : Name Plate )	-	75	-
12.7.6.1( Test of insulation Properties : General test conditions )	-	0	Charges are already given in clause 12.7.6.2 , 12.7.6.3 ,12.7.6.4
12.7.6.2(Impulse voltage test)	-	4000	-
12.7.6.3(ac Voltage test)	-	1000	-
12.7.6.4(Insulation resistance test)	-	1000	-
12.10.1 a)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
12.10.1 b)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
12.10.1 c)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
12.10.1 d)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
12.10.1 e)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
12.10.1 f)(Testof Accuracy Requirements : General Test Conditions )	-	1000	-
11.1(Limits of Error and Interpretation or Test Results)	-	0	-
12.16 a)(Limits of Error and Interpretation or Test Results)	-	200	-
12.16 b)(Limits of Error and Interpretation or Test Results)	-	200	-
12.16 c)(Limits of Error and Interpretation or Test Results)	-	200	-
12.15(Test of Meter Constant/Registration)	-	1000	-
12.14(Test of Starting Conditions)	-	1000	-
12.13(Test of No-Load Condition)	-	1500	-
12.12(Test ofAmbient Temperature Influence)	-	1500	-
12.17(Repeatability of Error Test )	-	1500	-
12.11(Test of Iniluence Quantities)	-	5000	-
12.7.1(Test of Power Consumption)	-	1500	-
12.7.2(Test of Influence of Supply Voltage)	-	1500	-
12.7.3( Test of Influence of Short-time Overcurrents)	-	2000	-
12.7.4(Test of Influence of Self-Heating)	-	2000	-
12.7.5(Test of Influence of Heating)	-	2000	-
12.8(TestorImmunity to Earth Fault)	-	1000	-
12.4(Testof Resistance to Heat and Fire )	-	4000	-
12.3.3( Spring Hammer Test)	-	2000	-
12.6.1(Dry Heat Test)	-	8000	-
12.6.2(Cold Test)	-	8000	-
12.6.3( Damp Heat Cycle Test)	-	8000	-
12.5 b)(Test of Protection Against Penetration of Dust and Water)	-	8000	-
12.3.2(Vibration Test)	-	6000	-
12.3.1(Shock Test)	-	5000	-
12.9.4(FastTransient BurstTest)	-	6000	-
12.9.2(Test for Immunity to Electrostatic Discharge (ESD))	-	6000	-
12.9.3(Test for Immunity to EIectromagnetic HF Fields)	-	6000	-
12.9.5(Radio Interference Measurement)	-	6000	-

Complete

09 Oct, 2024

-
Class1 and 2. Exclusion: Protection against solar radiation (Cl.12.6.4)

Bureau of Indian Standards

The National Standards Body of India

ELECTRONICS AND QUALITY DEVELOPMENT CENTRE

B 177/178 & B/23/2, GIDC ELECTRONICS ESTATE, SECTOR 25, Gandhinagar, Gandhinagar, Gujarat, 382024

9427418080 qm@eqdc.in

Scope List