BIS - LIMS (Laboratory Information Management System)

Delta Testing & Research Laboratories

Plot No. C-5, Block-C, Main Kanjhawala Road, Rajiv Nagar, New Delhi, North West, Delhi, 110086

9910596777 dtrlinfo@gmail.com

Scope List

Reset

96 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions of pipe - i) Outside diameter)	-	500	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
6(Visual Appearance)	-	500	-
7.1(Hydraulic Characteristics - Quality test)	-	4000	-
7.1(Hydraulic Characteristics - Acceptance test)	-	4000	-
7.2(Reversion Test)	-	2000	-
7.3(Tensile Test- i) Tensile Strength)	-	2000	-
7.3(Tensile Test - ii)Elongation at Break)	-	2000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	4000	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	4000	-
7.5(Density)	-	500	-
7.6(Melt Flow Rate)	-	500	-
4.2(Carbon black- a)carbon content)	-	500	-
4.2(Carbon black- b) Dispersion of carbon black)	-	500	-
7.6(Melt now Rate (MFR))	-	500	-
6.1(VISUAL APPEARANCE)	-	500	-
5.1.2(Ovality)	-	500	-
4.3(Anti-oxidant)	-	500	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	500	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	500	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	500	-
3(CLASSIFICATION OF PIPES)	-	500	-
4.1(Quick Coupled Male and Female Couplers)	-	500	-
4.1.3(Workmanship and appearance)	-	500	-
4.1.4(Holding attachments for coupler parts)	-	500	-
4.1(Quick Coupled Male and Female Couplers)	-	500	-
6.1.3(Weldability Test- a) Quality test)	-	4000	-
6.1.3(Weldability Test- b) Acceptance test)	-	4000	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	4000	-
4.1 (b)(HDPE couplers —)	-	500	-
4.1 .1.2.1(HDPE couplers)	-	500	-
4.1 .1.2.2(HDPE couplers)	-	500	-
6.1.1, 6.1.1.1(Leakage Test)	-	500	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	4000	-
6.1.2.2(Hydraulic Proof Test)	-	4000	-

Complete

31 Aug, 2023

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

All Grade

23660 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	500	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	500	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	500	-
6.1.3 (Length of Pipe)	-	500	-
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	500	-
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	500	-
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	500	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	500	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	500	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	500	-
6.1.4.1 (e3min=0.75e)	-	500	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	500	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	500	-
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	500	-
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	500	-
7(Physical characteristics )	-	500	-
7.1(Appearance:- )	-	500	-
7.2(Colour )	-	500	-
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	500	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	500	-
8(MECHANICAL CHARACTERISTICS)	-	1000	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	500	-
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	1000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	1000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	1000	-
9.2 IS 14182(b) Solvent cement)	-	500	-
10(Performance requirements)	-	1000	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	-
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1000	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	-
'7.5 (amdt.7)(Effect on Water (Type test))	-	1500	-

Complete

31 Aug, 2023

IS 15965 (2012)

Pre - Painted aluminium zinc alloy metallic coated steel strip and sheet (Plain)

All Grade

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	500	-
Cl 8.3.1(Adhesion )	-	500	-
Cl 8.3.2(Impact Resistance)	-	500	-
Cl 8.4(Load Resistance)	-	500	-
Cl 8.5(Scratch Resistance)	-	500	-
Cl 8.7(Dry Film Thickness)	-	500	-
Cl 9.1(Workmanship)	-	500	-
Cl 10.1(Corrosion Test)	-	500	-
Cl 10.2(Humidity Test)	-	500	-
Cl 11(Length, Width & Thickness)	-	500	-
Cl 12(Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-	500	-
Cl 12(Weight)	-	500	-
8.6(Solvent Resistance test)	-	500	-
9.2(colour)	-	500	-
9.3(Gloss (60 Deg))	-	500	-
4, 5(CARBON)	-	500	-
4, 5(SULPHUR)	-	500	-
4, 5(PHOSPHURS)	-	500	-
4, 5(MANGANESE)	-	500	-
4, 5(NITROGEN)	-	500	-
4, 5(SILICON)	-	500	-
4, 5(ALUMINIUM)	-	500	-
13(IS 15965)	-	500	-

Complete

31 Aug, 2023

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

All Grade

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1, 5.1, 8.1 & 8.2(Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Chromium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Molybdenum: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Vanadium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Nickel: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Copper: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Aluminium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Niobium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Titanium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
Table-1, 5.1, 8.1 & 8.2(Boron: Relevant parts of IS 228 or any other established instrumental/chemical method)	-	500	-
7(Freedom from defects)	-	500	-
5 and 10.3.1(Tensile strength. IS 1608)	-	500	-
5 and 10.3.1(Yield Stress. IS 1608)	-	500	-
5 and 10.3.1(Percentage Elongation. . IS 1608)	-	500	-
11.3( Bend Test. IS 1599)	-	500	-

Complete

31 Aug, 2023

IS 15834 (2020)

Stainless Steel Sliding Door Bolts ( Aldrops ) for Use With Padlocks - Specification ( First Revision )

All Grade

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(DIMENSIONS AND TOLERANCES)	-	3000	-
Cl 6(MANUFACTURE)	-	3000	-
7(FINISH)	-	3000	-

Complete

31 Aug, 2023

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

All Grade

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	500	-
4.1(Raw Material)	-	500	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
4.2(Tapes – Linear Density )	-	500	-
4.2(Construction)	-	500	-
4.3(Sacks)	-	500	-
4.3.1(Bottom Seam)	-	500	-
4.3.1(The two rows of stitches shall be separated from each other)	-	500	-
4.3.1( The outer stitch)	-	500	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	500	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	500	-
4.3.1(stitches/dm)	-	500	-
4.3.2(Mouth)	-	500	-
4.4(Liner IS 10146 or IS 10910.)	-	500	-
4.4(Mass of the loose liner )	-	500	-
4.4(Width of the loose liner)	-	500	-
4.4(Length of the line)	-	500	-
4.4(Bottom seam of the loose liner)	-	500	-
4.4.1(Liner)	-	500	-
4.5 and Table 1 i(Capacity)	-	500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	500	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	500	-
5.2 and Table 1 x(Ash content )	-	500	-

Complete

31 Aug, 2023

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

All Grade

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	500	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	500	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.3.1(Bottom seam (IS 10789))	-	500	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	500	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	500	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	500	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	500	-
4.2 and Table 1 x(Ash content )	-	500	-
3.1(Material Identification)	-	500	-
3.1(Overall Migration)	-	500	-
3.2(Density)	-	500	-
3.2(MFI)	-	500	-

Complete

31 Aug, 2023

IS 14811 (2000)

Rolled copper plate, sheet, strip and foils for general engineering purposes - Specification

All Grade

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.12(Calculation of mass)	-	800	-
Cl.11 Table-4(Preferred Inside Diameter)	-	800	-
Cl.11(Dimensions and tolerances)	-	800	-
Cl.10(Hydrogen embrittlement test)	-	800	-
Cl.9 table-3(Cupping test, erichsen value)	-	800	-
Cl.8.3 Table-2(Longitudinal Bend Test Angle, radius)	-	800	-
Cl.8.3 Table-2(Transverse Bend Test Angle, radius)	-	800	-
Cl.8.3(Bend test)	-	800	-
Cl.8.1 Table-1(Hardness)	-	800	-
Cl.8.1 Table-1(Elongation percent)	-	800	-
Cl.8.1 Table-1(Tensile strength Mpa)	-	800	-
Cl.8(Mechnical properties)	-	800	-
Cl.7(Chemical composition)	-	800	-
Cl.6(Freedom from defects)	-	800	-

Complete

31 Aug, 2023

IS 14650 (1999)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling purposes - Specificaation

All Grade

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Nitrogen- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Aluminium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Titanium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Vanadium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Copper- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6(Niobium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
9 & 10(Dimensions and Tolerances )	-	500	-
11(Freedom from Defects )	-	500	-
12(Macro-examination )	-	500	-
12(Sulphur Print Tests )	-	500	-
Cl. 6.1(Nitrogen)	-	500	-
Cl. 6.1(Niobium)	-	500	-
Cl. 6.1(Titanium)	-	500	-
Cl. 6.1(Copper)	-	500	-
Cl. 6.1(Aluminium)	-	500	-
Cl. 6.1(Molybdenum)	-	500	-
Cl. 6.1(Chromium)	-	500	-
Cl. 6.1(Vanadium)	-	500	-
Cl. 6.1(Nickel)	-	500	-
Cl. 6.1(Manganese)	-	500	-
Cl. 6.1(Silicon)	-	500	-
Cl. 6.1(Carbon)	-	500	-

Complete

31 Aug, 2023

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

All Grade

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions and tolerances)	-	1000	-
10.2, Table-1(Test for Density)	-	1000	-
10.4, Table-1(Test for Water Absorption)	-	1000	-
10.5(test for swelling in water)	-	1000	-
10.6(test for modulis of rupture)	-	1000	-
10.7(Test for tensile strength perpendicular to Surface)	-	1000	-
10.8(Test for tensile strength perpendicular to Surface after ageing )	-	1000	-
10.9(test screw withdrawal strength)	-	1000	-
10.1(test for surface abrasion resistance)	-	1000	-
10.11(test for resistance to steam)	-	1000	-
10.12(test for resistance to crack)	-	1000	-
10.13(test for resistance to cigarette burn)	-	1000	-
10.14(test for resistance to stain)	-	1000	-

Complete

31 Aug, 2023

IS 14246 (2013)

Continuously pre-painted galvanized steel sheets and coils (First Revision)

All Grade

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	500	-
Cl 4.2(Workmanship)	-	500	-
Cl 4.3(Workmanship)	-	500	-
Cl 6.2(Press)	-	500	-
Cl 6.3(HWB)	-	500	-
Cl 6.4(Load Resistance)	-	500	-
Cl 6.5(Cross Hatch)	-	500	-
Cl 8(Salt Spray)	-	500	-
Cl 9(Length, Width, Thickness & Mass)	-	500	-
Cl 10(Camber, Deviation From Squareness (Out-of- Square) & Deviation From Flatness)	-	500	-
Cl. 9.4.4(Mass)	-	500	-
Cl. 10.2(Out of square)	-	500	-
Cl. 10.3, Table 4(Flatness)	-	500	-
Cl. 10.1(Camber)	-	500	-
Cl. 9.4.2(Width)	-	500	-
Cl. 7.3.1(Gloss Bottom Coat)	-	500	-
Cl. 7.3.1(Gloss Top Coat)	-	500	-
Cl. 7.3.2 Table 3(Color Bottom Coat)	-	500	-
Cl. 7.3.2 Table 3(Color Top Coat)	-	500	-
4,4.1,4.2(CARBON)	-	500	-
4,4.1,4.2(SULPHUR)	-	500	-
4,4.1,4.2(PHOSPHURS)	-	500	-
4,4.1,4.2(MANGANESE)	-	500	-
4,4.1,4.2(NITROGEN)	-	500	-
4,4.1,4.2(ALUMINIUM)	-	500	-

Complete

31 Aug, 2023

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

All Grade

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	500	-
6.2, 6.2.1 (Quick Coupled Fittings)	-	500	-
6.1.3.2 (Quick coupled fittings)	-	500	-
6.1.3.1.1(Weldability Test)	-	500	-
6.1.2.2( Hydraulic Proof Test)	-	500	-
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	500	-
6.1.1, 6.1.1.1(Leakage Test)	-	500	-
6.1.1, 6.1.1.1(Leakage Test)	-	500	-
6.1(Quick Coupled Pipes and Fittings)	-	500	-
5.3(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500	-
5.2(Dimensions of Quick Coupled Pump Connectors Table 3.)	-	500	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	500	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	500	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	500	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	500	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	500	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	500	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	500	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	500	-
4.1.5(Rubber Ring)	-	500	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	500	-
4.1 .3(Workmanship and Appearance)	-	500	-
4.1 .1.2.2(HDPE couplers)	-	500	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	500	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	500	-
Cl.6.1.3(Weldability Test- b) Acceptance test)	-	500	-
Cl.6.1.3(Weldability Test- a) Quality test)	-	500	-
Cl 4.1.5(Rubber rings- C)Rubber ring shall be of black colour:)	-	500	-
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	500	-
Cl 4.1.5(Rubber rings- A)Shore hardness (Shore-A))	-	500	-
Cl 4.1.4(Holding attachments for coupler parts)	-	500	-
Cl.4.1.3(Workmanship and appearance )	-	500	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	500	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	500	-
4.1.1.2.1(Density)	-	500	-
4.1.1.2.1(MFI @ 1900C/5.0 Kg)	-	500	-
4.1.1.2.1(Density at 27°C (Base material))	-	500	-
4.1.1.2.1(Melt flow rate at 190°C/5 kg)	-	500	-
4.1.1.2.1(Female coupler (min))	-	500	-
4.1.1.2.1(Male coupler (min))	-	500	-
4.1.5(a. Identification of Rubber Ring)	-	500	-
4.1.5(b. Colour of rubber ring)	-	500	-
4.1.5(c. Change in hardness after keeping it in air at 70°C for 7 days)	-	500	-
3.0((a) Outside diameter)	-	500	-
3.0((i)Quality Test at 3.5MPa induced stress for 165 hours at 80°C)	-	500	-
3.0(Reversion test)	-	500	-
3.0(Tensile strength at yield)	-	500	-
3.0(Elongation at break)	-	500	-

Complete

31 Aug, 2023

IS 13801 (2013)

Chequered Cement Concrete Tiles -

All Grade

6800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	900	-
Cl 12.1(Concavity & Convexity )	-	900	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	900	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	900	-
Cl 12.4(Water absorption)	-	900	-
Cl 12.5(Wet transverse strength)	-	900	-
Cl 12.6(Resistance to wear)	-	900	-
Cl 11(Finish)	-	900	-

Complete

31 Aug, 2023

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

All Grade

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Grades & Types)	-	1000	-
Cl 6(Manufacture)	-	1000	-
Cl 7(Finish)	-	1000	-
Cl 8(Dimensions & Tolerances)	-	1000	-
Cl 10.2(Test For Density)	-	1000	-
Cl 10.3(Test For Moisture Content)	-	1000	-
Cl 10.4(For Water AbsorptionTest )	-	1000	-
Cl 10.5(For Swelling in water Test )	-	1000	-
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1000	-
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1000	-
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	1000	-
Cl 10.9(Test For Screw Withdrawal Strength)	-	1000	-
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	1000	-
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	1000	-
Cl 10.12 & Annex E( Test For Crack Resistance)	-	1000	-
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	1000	-
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	1000	-

Complete

31 Aug, 2023

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

All Grade

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 5.2, 9 and 10.2.2(Density)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Density)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Variation from mean density)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Moisture Content)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Variation from mean moisture content)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Internal Bond Strength)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Internal Bond strength (i) (After Cyclic test) (ii) (After accelerated water resistance test))	-	1000	-
Clauses 5.2, 9 and 10.2.2(Modulus of Rupture a) Avg. Value b) Min. Individual)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Modulus of Elasticity a) Avg. Value b) Min. Individual)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-	1000	-
Clauses 5.2, 9 and 10.2.2(Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Steady State Formaldehyde emission (Fc (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	1000	-

Complete

31 Aug, 2023

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

All Grade

5600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	500	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1( Nb)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Boron)	-	500	-
6.1( Nitrogen%)	-	500	-
6.1(Microalloying)	-	500	-
Cl. 10(Weight)	-	500	-
Cl. 9.3(Crown)	-	500	-
Cl.9.3.1(Difference in Thickness)	-	500	-
Cl. 9.5(Edge Camber)	-	500	-
Cl.9(Thickness)	-	500	-
Cl.9(Width)	-	500	-

Complete

31 Aug, 2023

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

All Grade

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	500	-
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
7.1(Carbon %)	-	500	-
7.1(Manganese %)	-	500	-
7.1(Phosphorus %)	-	500	-
7.1(Sulphur %)	-	500	-
7.1(Silicon %)	-	500	-
7.1( Copper %)	-	500	-
7.1( Aluminium %)	-	500	-
7.1( Nb)	-	500	-
7.1(V)	-	500	-
7.1( Ti)	-	500	-
7.1(Cr)	-	500	-
7.1(Mo)	-	500	-
7.1(Ni)	-	500	-
7.1( Nitrogen%)	-	500	-
7.1(CE)	-	500	-
Cl. 14(Weight)	-	500	-
Cl. 12, 13(Camber)	-	500	-
Cl. 12, 13(Thickness)	-	500	-
Cl. 8, Table 3(Elongation)	-	500	-
Cl. 8, Table 3(Yield Stress)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-

Complete

31 Aug, 2023

IS 8042 (2015)

White portland cement - Specification (Third Revision)

All Grade

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	500	-
5 - Table - 1 ii(Iron oxide - Cl 4.5 of IS 4032:1985)	-	500	-
5 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	500	-
5 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	500	-
5 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	500	-
5 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	500	-
5 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 -Table 2- i(Fineness 4031 Part 2)	-	500	-
6 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
6 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	-
6 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	-
6-Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	-
6 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
6 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
6 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	-
6 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	-
6 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	-
6 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	500	-
6 -Table 2- vi(Degree of whiteness-Annex B)	-	500	-
6, table-2, ii(Whiteness)	-	500	-

Complete

31 Aug, 2023

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

All Grade

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	500	-
Cl 9(Nominal Diameter & Out Of Shape)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-

Complete

31 Aug, 2023

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

All Grade

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	500	-
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	500	-
6(Freedom from defects , IS 6911)	-	500	-
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	500	-
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	500	-
10.3(Bend Test - IS 1599)	-	500	-
11,Table 7(Erichsen cupping test-IS 10175)	-	500	-
15(Surface Finish)	-	500	-
17(Dimension and tolerance)	-	500	-
10.1 Amd 2(Yeild Strength)	-	500	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	500	-
10.1 Amd 2(Elongation)	-	500	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	500	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	500	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	500	-
Clause 17 , Table 9 to Table 19(Flatness)	-	500	-
Clause 17 , Table 9 to Table 19(Camber)	-	500	-
Table 1(Any Instrumental Method/Chemical Method)	-	500	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	500	-

Complete

31 Aug, 2023

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

All Grade

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 7(Workmanship)	-	1000	-
Cl 6(Workmanship)	-	1000	-
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	1000	-
Cl 10(UTM)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nitrogen)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Titanium)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Vanadium)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Boron)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Copper)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Molybdenum)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nickel)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Chromium)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Aluminium)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Silicon)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Manganese)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Phosphorous)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Sulphor)	-	1000	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Carbon)	-	1000	-

Complete

31 Aug, 2023

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

All Grade

12450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Table 1)(b) 6 mm and above)	-	12450		-

Complete

31 Aug, 2023

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

All Grade

17925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	800	-
7.2(DIMENSIONS & TOLERANCES )	-	800	-
7.3(DIMENSIONS & TOLERANCES )	-	800	-
7.4(DIMENSIONS & TOLERANCES )	-	800	-
8.1(WORKMANSHIP AND FINISH )	-	800	-
8.3(WORKMANSHIP AND FINISH )	-	800	-
10.1.1(MOISTURE CONTENT)	-	800	-
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	800	-
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	800	-
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	800	-
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	800	-
10.1.4(RESISTANCE TO WATER TEST)	-	800	-
10.1.5(MYCOLOGICAL TEST )	-	800	-
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	800	-
10.1.5.2(MYCOLOGICAL TEST )	-	800	-
10.1.6(TENSILE STRENGTH)	-	800	-
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	800	-
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	800	-
10.1.9(RETENTION OF PRESERVATIVE)	-	800	-
12, 12.1(MARKING)	-	800	-
12, 12.2(MARKING)	-	800	-
12, 12.2(MARKING)	-	800	-

Complete

31 Aug, 2023

IS 4948 (2020.0)

Welded steel wire fabric for general use - Specification (Second Revision)

All Grade

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1(MATERIALS)	-	500	-
Cl. 4.2(MATERIALS)	-	500	-
Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires))	-	500	-
Cl. 5.2(MANUFACTURE OF MESH)	-	500	-
Cl. 5.3(MANUFACTURE OF MESH)	-	500	-
Cl. 5.4(Spacing of Longitudinal and Transverse Wires)	-	500	-
Cl. 5.5(Tolerance of Size of Mesh)	-	500	-
Cl. 5.6(Tolerance of Size of Sheet or Roll)	-	500	-
Cl. 6(TEST FOR WELDING)	-	500	-
Cl. 9.1(Marking)	-	500	-
Cl. 9.3(BIS Certification Marking)	-	500	-
Cl. 10.1(Finish)	-	500	-

Complete

31 Aug, 2023

IS 4454 : Part 2 (2001)

Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision)

All Grade

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	1000	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	6000	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	6000	-
7.1, 7.2(Vanadium)	-	500	-
7.1, 7.2(Chromium)	-	500	-
7.1, 7.2(copper)	-	500	-
7.1, 7.2(phosphorus)	-	500	-
7.1, 7.2(sulphur)	-	50	-
7.1, 7.2(manganese)	-	500	-
7.1, 7.2(silicon )	-	500	-
7.1, 7.2(carbon)	-	500	-

Complete

31 Aug, 2023

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

All grade

11325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	500	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	5500	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	5500	-
7.1, 7.2(copper)	-	500	-
7.1, 7.2(Vanadium)	-	500	-
7.1, 7.2(phosphorus)	-	500	-
7.1, 7.2(sulphur)	-	500	-
7.1, 7.2(manganese)	-	500	-
7.1, 7.2(silicon )	-	500	-
7.1, 7.2(carbon)	-	500	-
7.1, 7.2(Chromium)	-	500	-
7.1, 7.2(micro alloy)	-	500	-
7.1, 7.2(cu + cr+ni)	-	500	-
7.1, 7.2(sulphur + phosphorus)	-	500	-

Complete

31 Aug, 2023

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

All Grade

11250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Tensile Test & Flattening Test)	-	2500	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	1000	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	1000	-
Cl 10(Outer Diameter & Overall Length)	-	1000	-
Cl 12(Bituminous Coating & Galvanizing )	-	1000	-
Cl 14(Workmanship)	-	1000	-
5.2(phosphorus)	-	2500	-
5.2(sulphur)	-	2500	-

Complete

31 Aug, 2023

IS 3812 : Part 2 (2013)

Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

All Grade

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ) plus aluminium oxide (Al2O3 ) plus iron oxide (Fe2O3 ))	-	500	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ))	-	500	-
5.1, 6.1, Table 1(Magnesium oxide (MgO)	-	500	-
5.1, 6.1, Table 1(Total sulphur as sulphur trioxide (SO3)	-	500	-
5.1, 6.1, Table 1(Available alkalies as equivalent sodium oxide (Na2O))	-	500	-
5.1, 6.1, Table 1(Total chlorides)	-	500	-
5.1, 6.1, Table 1(Loss on ignition)	-	500	-
6.2(moisture content)	-	500	-
7.1, Table 1(Fineness — Specific surface in m2 /kg)	-	500	-
7.1, Table 1(Particles retained on 45 micron IS sieve (wet sieving))	-	500	-
7.1, Table 1(Soundnes)	-	500	-
7.2(Uniformity Requirements)	-	500	-
11.1(Supplies of pulverized fuel)	-	500	-
11.2(Tolerance Requirements for the Quantity of Pulverized Fuel Ash Packed in Bags)	-	500	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (iii) (Soundness by autoclave test - Expansion of specimen)	-	500	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (ii) (Particles retained on 45 micron IS Sieve (we sieving))	-	500	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (i) (Fineness- Specific surface by blaine's method)	-	500	-

Complete

31 Aug, 2023

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

All Grade

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	800	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	800	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	800	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	800	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	800	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	800	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	800	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	800	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	800	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	800	-
7.2(Uniformity Requirements)	-	800	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	800	-

Complete

31 Aug, 2023

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

All Grade

9450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	500	-
13(Mechanical Testing)	-	500	-
6.0(Workmanship)	-	500	-
4.1(Sulphur-Percentage by mass)	-	500	-
4.1(Phosphorus-Percentage by mass)	-	500	-
8.0(Straightness)	-	500	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	500	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	500	-
11.1(Surface Protection)	-	500	-
11.2(Surface Protection)	-	500	-
13.1.3(Tensile Strength)	-	500	-
13.1.1(Yield Stress)	-	500	-
13.1.2(Elongation)	-	500	-
13.2(Flattening Test)	-	500	-
13.3(Bend Test (Strip))	-	500	-
13.4(Bend Test (Whole Tube))	-	500	-
13.5(Drift Expansion Test)	-	500	-
13.6(Crush Test)	-	500	-
19.1.3(Height of Internal Fin)	-	500	-
Cl. 10 Annex B Cl. 17, Cl. 19(Moment of inertia)	-	500	-
Cl. 10 Annex B Cl. 17, Cl. 19(Radius of gyration)	-	500	-
Cl. 10 Annex B Cl. 17, Cl. 19(Modulus of section)	-	500	-
Cl. 10 Annex B Cl. 17, Cl. 19(Area of cross section)	-	500	-
Cl. 19.1.3(Internal Fin Height)	-	500	-
Cl. 10 Annex B Cl. 17, Cl. 19(Mass)	-	500	-
Cl. 9(Length)	-	500	-

Complete

31 Aug, 2023

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Delta Testing & Research Laboratories

Plot No. C-5, Block-C, Main Kanjhawala Road, Rajiv Nagar, New Delhi, North West, Delhi, 110086

9910596777 dtrlinfo@gmail.com

Scope List