BIS - LIMS (Laboratory Information Management System)

MSME TESTING CENTRE, CHENNAI

65/1, GST Road, Guindy, Chennai, Chennai, Tamil Nadu, 600032

9445662299 dctc-sr@dcmsme.gov.in

Scope List

Reset

47 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

8800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	0	-
Cl. No.5("SIZE AND FITTINGS ")	-	0	-
Cl. No.6("CONSTRUCTION ")	-	0	-
Cl. No.7(MATERIAL)	-	0	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	300	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	0	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	400	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	300	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	500	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	0	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	300	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	500	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	0	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	300	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	200	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	300	-
Cl. No.8.4,Table no. 5(i)(Density)	-	200	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	300	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	400	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	300	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	300	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	300	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	300	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	300	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	300	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	300	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	600	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	300	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	300	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	900	-
Cl. No.8.6.2(Lead content)	-	200	-
Cl. No.9.(MARKING AND PACKING)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	300	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	100	-
Cl-5 ((Amendment No-1)(Category And Type)	-	100	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	600	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	500	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	500	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	2000	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	500	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	600	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	1200	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	800	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	600	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	400	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	500	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	500	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	600	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	500	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	700	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	500	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	700	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	400	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	400	-
Cl-10 (Amendment No-1)(Marking)	-	100	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	400	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	500	-

31 Dec, 2026

-
-

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	0	-
Cl-4.3.1(Size)	-	100	-
Cl-4.3.2(Weight)	-	100	-
Cl-4.4(Height of Upper)	-	200	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	100	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	600	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	1200	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	700	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	700	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	800	-
Cl-4.6.1(Material)	-	100	-
Cl-4.6.2(Tear Strength)	-	500	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	800	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	400	-
Cl-4.7.1(Material)	-	100	-
Cl-4.7.2(Tear Strength)	-	500	-
Cl-4.7.3(Abrasion Resistance)	-	800	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	800	-
Cl. 4.8.1(Material)	-	100	-
Cl-4.8.2(Abrasion Resistance)	-	400	-
Cl-4.8.3(Water Absorption and Desorption)	-	1200	-
Cl-4.9.3(Abrasion Resistance)	-	800	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	100	-
Cl-4.11.1(Material)	-	100	-
Cl-4.11.2(Tear Strength)	-	500	-
Cl-4.12(Closing Thread)	-	400	-
Cl-4.13.2(Thickness)	-	100	-
Cl-4.13.3(Moulded Density)	-	400	-
Cl-4.13.4(Hardness)	-	400	-
Cl-4.13.5(Ageing Test)	-	500	-
Cl-4.13.6(Tear Strength)	-	500	-
Cl-4.13.7(Abrasion Resistance)	-	800	-
Cl-4.13.8(Flexing Resistance)	-	600	-
Cl-4.14(Eyelet)	-	500	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	500	-
Cl-7(Marking)	-	100	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	600	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	600	-
Cl.4.5.3.2(Interlayer bond strength)	-	600	-

31 Dec, 2026

-
-

IS 17043 : Part 2 (2024)

Shoes: Shoes for General Purpose

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Shape and Design)	-	0	-
Cl-5.3(Material)	-	0	-
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	600	-
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	600	-
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	1200	-
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	500	-
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	500	-
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	400	-
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	500	-
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	500	-
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	500	-
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	500	-
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	800	-
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	400	-
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	2000	-
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	500	-
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	600	-
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	500	-
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	500	-
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	800	-
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	500	-
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	800	-
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	1000	-
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	500	-
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	500	-
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	500	-
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	500	-
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	600	-
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	800	-
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	2000	-
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	800	-
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	1000	-
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	500	-
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	800	-
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	500	-
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	500	-
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	800	-
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	500	-
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	400	-
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	600	-
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	100	-
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	800	-
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	600	-
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	600	-
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	2000	-
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	400	-
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	0	-
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	400	-
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	400	-
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	800	-
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	600	-
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	400	-
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	500	-
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	400	-
Cl-6.7, Table-14 (i)(Hardness, N)	-	500	-
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	600	-
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	700	-
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	500	-
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	500	-
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	600	-
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	500	-
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	400	-
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	700	-
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	500	-
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	500	-
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	500	-
Cl-8.1(Marking)	-	100	-
Cl-6.7, Table-14 (iv)(Area shape retention, percent (a) Initial, Min b) After 10 collapsing load, Min)	-	600	-
Cl-6.7, Table-14 (v)(Adhesion strength, N/mm)	-	600	-
Cl-6.8, Table-15 (i)(Peel strength, N/mm a) Initial, Min b) After 5 000 wear cycles, Min)	-	800	-
Cl- 6.8, Table-15 (ii)(a) Shear strength, kPa b) Initial, Min)	-	800	-
Cl- 6.9, Table-16 (i)(Limit of useful extension, percent, Min)	-	500	-
Cl- 6.9, Table-16 (ii)(Needle strength, N/mm, Min)	-	500	-
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	1000	-

31 Dec, 2026

-
-

IS 10702 (2023)

Hawai Chappal-Specification

4100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	0	OK
4.2(Length)	-	0	OK
4.4 , Table No. 1 , i)(Density)	-	300	OK
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	300	OK
4.4 , Table No. 1 , iii)(3Split tear strength)	-	300	OK
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	300	OK
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	300	OK
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	300	OK
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	300	OK
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	300	OK
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	300	OK
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	0	OK
4.4 , Table No . 2 , iv)(Stud bolt)	-	0	OK
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	300	OK
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	300	OK
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	0	OK
6(MARKING AND PACKING)	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	0	OK
Cl.No. 5.2(lead content)	-	400	OK
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	300	OK
4.3(Thickness)	-	100	OK
Cl-4 ((Amendment No-1)(Category And Type)	-	0	OK
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	400	OK
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	500	OK
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	400	OK
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	400	OK
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	800	OK
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	600	OK
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2000	OK
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	400	OK
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	OK
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	500	OK
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	500	OK
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	400	OK
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	500	OK
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	500	OK
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	600	OK
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	400	OK
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	400	OK

31 Dec, 2026

-
-

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

16800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.1(Sampling and Conditioning)	-	0	-
Cl No.4.2(Construction)	-	0	-
Cl No.4.3(Whole Footwear)	-	0	-
4.3.1(Insole)	-	0	-
4.3.2(Toe spring height)	-	0	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	0	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	0	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	0	-
4.3.6(Energy Absorption at Seat Region)	-	0	-
4.3.7(Complete Shoe Flexing)	-	0	-
4.3.9(Slip Resistance)	-	0	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	0	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	0	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	0	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	0	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	0	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	0	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	0	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	0	-
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	0	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	0	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	0	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	0	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	0	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	0	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	0	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	0	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	0	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	0	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	0	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	0	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	0	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	0	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	0	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	0	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	0	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	0	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	0	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	0	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	0	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	0	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	0	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	0	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	0	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	0	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	0	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	0	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	0	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	0	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	0	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	0	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	0	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	0	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	0	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	0	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	0	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	0	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	0	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	0	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	0	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	0	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	0	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	0	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	0	-
Cl No . 5(MARKING AND PACKING)	-	0	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	0	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	0	-
Clause 4.2 - 4.2.1(Construction)	-	0	-
Clause 4.2 - 4.2.2(Construction)	-	0	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	0	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	0	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	0	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	0	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	0	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	0	-
Clause 4.4, Table 1 ii)(Tear strength)	-	0	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	0	-
Clause 4.4, Table 1 iv)-b(Water Vapour Coeffecient)	-	0	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	0	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	0	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	0	-
Clause 4.4, Table 2 iii)(Tear strength)	-	0	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	0	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	0	-
Clause 4.5, Table 3 i)(Tear strength)	-	0	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	0	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	0	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	0	-
Clause 4.6, Table 4 i)(Thickness)	-	0	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	0	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	0	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	0	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	0	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	0	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	0	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	0	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	0	-
Cl-5, Table -1 S. No-(i) (Amendment No-1)(Insole)	-	100	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1)(Toe spring height)	-	200	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1)("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-	600	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1)(Energy absorption at seat region)	-	600	-
Cl-5, Table -1 S. No- (v) (Amendment No-1)(Complete shoe flexing)	-	1000	-
Cl-5, Table -1 S. No- (vii) (Amendment No-1)(Slip resistance, coefficient of friction (COF),)	-	1200	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1)("Abrasion resistance a-Cellular sole b-Solid sole")	-	800	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1)(Hydrolysis resistance)	-	2000	-
Cl-5, Table -1 S. No- (xii) (Amendment No-1)(Lead content)	-	400	-
Cl-6, Table -2 S. No- (i) (Amendment No-1)(Tear strength)	-	500	-
Cl-6, Table -2 S. No- (ii) (Amendment No-1)("Colour fastness rubbing a-Dry: (rubbing) b-Wet: (rubbing)")	-	500	-
Cl-6, Table -2 S. No- (iii), a) (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -2 S. No- (iii), b) (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -2 S. No- (iv),(Amendment No-1)(Stitch tear strength)	-	500	-
Cl-6, Table -2 S. No- (v),(Amendment No-1)(Colour fastness to light grey scale rate,)	-	700	-
Cl-6, Table -3 S. No- (i),(Amendment No-1)(Breaking strength, N/mm, Min)	-	500	-
Cl-6, Table -3 S. No- (ii),(Amendment No-1)("Elongation at break a-Tighter direction b-Stretch direction")	-	500	-
Cl-6, Table -3 S. No- (iii),(Amendment No-1)("Tear strength, N, Min a) For fabric b) For all other materials")	-	500	-
Cl-6, Table -3 S. No- (iv),(Amendment No-1)("Flexing resistance a- Dry condition b-Wet condition")	-	600	-
Cl-6, Table -3 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -3 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -3 S. No- (vi), (Amendment No-1)(Hydrolysis resistance)	-	2000	-
Cl-6, Table -3 S. No- (vii), (Amendment No-1)(Bursting strength)	-	500	-
Cl-6, Table -4 S. No- (i),(Amendment No-1)(Tear strength, N, Min)	-	500	-
Cl-6, Table -4 S. No- (ii),(Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	700	-
Cl-6, Table -4 S. No- (iii),(Amendment No-1)(Colour fastness to rubbing , grey scale rate with 10 rubs on dry or wet, Min)	-	500	-
Cl-6, Table -4 S. No- (iv),(Amendment No-1)(Colour fastness to perspiration)	-	500	-
Cl-6, Table -4 S. No- (v), a (Amendment No-1)(Water vapour permeability)	-	800	-
Cl-6, Table -4 S. No- (v), b (Amendment No-1)(Water vapour coefficient)	-	800	-
Cl-6, Table -5 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	100	-
Cl-6, Table -5 S. No-(ii), (Amendment No-1)(Flexing index, Min)	-	400	-
Cl-6, Table -5 S. No-(iii), (Amendment No-1)(Abrasion resistance,)	-	400	-
Cl-6, Table -5 S. No- (iv), a (Amendment No-1)(Water absorption)	-	600	-
Cl-6, Table -5 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	600	-
Cl-6, Table -6 S. No- (i), (Amendment No-1)(Thickness, mm, Min)	-	250	-
Cl-6, Table -6 S. No- (ii), (Amendment No-1)("Abrasion resistance, cycles a- Dry condition b-Wet condition")	-	800	-
Cl-6, Table -6 S. No- (iii),a (Amendment No-1)(Water absorption)	-	600	-
Cl-6, Table -6 S. No- (iv), b (Amendment No-1)(Water desorption, percent)	-	600	-
Cl-6, Table -7 S. No- (i), (Amendment No-1)(Flexing resistance (Belt method or Bennewart method))	-	700	-
Cl-6, Table -7 S. No- (ii), (Amendment No-1)(Hydrolysis resistance, cut growth after flexes)	-	2000	-
Cl-6, Table -8 S. No- (i), (Amendment No-1)("Compression set, percent, Max a) For EVA b) For all other materials")	-	400	-
Cl-6, Table -8 S. No- (ii), (Amendment No-1)(Split tear strength)	-	500	-
Cl-6, Table -8 S. No- (iii), (Amendment No-1)(Heat shrinkage)	-	400	-
Cl-6, Table -9 S. No- (i), (Amendment No-1)(First dry collapsing load, hardness)	-	600	-
Cl-6, Table -9 S. No- (ii), (Amendment No-1)(Resilience, percent)	-	600	-
Cl-6, Table -9 S. No- (iii), (Amendment No-1)(Moisture resistance)	-	700	-
Cl-6, Table -9 S. No- (iv), a (Amendment No-1)(Initial dry area shape retention)	-	600	-
Cl-6, Table -9 S. No- (iv), b (Amendment No-1)(Area shape retention after 10th collapse)	-	600	-
Cl-6, Table -10 S. No- (i), (Amendment No-1)("Peel strength a) Initial b) After 5 000 wear cycles")	-	800	-
Cl-6, Table -10 S. No- (ii), (Amendment No-1)("Shear strength a) Initial b) After 5 000 wear cycles")	-	800	-
Cl-6, Table -11 S. No- (i), (Amendment No-1)(Limit of useful extension)	-	500	-
Cl-6, Table -12 S. No- (i), (Amendment No-1)(Breaking strength of lace)	-	500	-
Cl-6, Table -12 S. No- (ii), (Amendment No-1)(Lace tag strength)	-	500	-
Cl-6, Table -12 S. No- (iii), (Amendment No-1)(Lace to lace abrasion)	-	600	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No- (iv), (Amendment No-1)(Colour fastness to water (for lace) (contact method))	-	500	-
Cl-6, Table -12 S. No (v), (Amendment No-1)(Strength of buckle/ski hook)	-	500	-
Cl-6, Table -12 S. No- (vi), (Amendment No-1)(Corrosion resistance)	-	400	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	500	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	600	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	600	-
Clause 4.7, Table 5 i)(Thickness)	-	250	-

31 Dec, 2026

-
-

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

18800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SAMPLING AND CONDITIONING)	-	0	-
5(DESIGN)	-	0	-
6(SIZE AND FITTINGS)	-	0	-
7.1.1(Whole Footwear)	-	0	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	600	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	600	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	600	-
7.1.5(Energy Absorption at Seat Region)	-	600	-
7.1.6(Complete Shoe Flexing)	-	1000	-
7.1.8(Slip Resistance)	-	1200	-
7.1.9(Heel Drop)	-	100	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	600	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	500	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	500	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	800	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	800	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	500	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	700	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	500	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	500	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	400	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	700	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	500	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	500	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	500	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	500	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	600	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	800	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	800	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	2000	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	700	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	500	-
7.3 , Table No. 4 , i)(Tear strength,)	-	500	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	500	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	500	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	500	-
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	800	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	800	-
7.4 , Table No. 5 , i)(Thickness)	-	250	-
7.4 , Table No. 5 , ii)(Flexing index)	-	500	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	400	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	600	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	600	-
7.5 , Table No. 6 , i)(Thickness)	-	250	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	700	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	600	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	600	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	400	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	800	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	700	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	2000	-
7.6 , Table No. 7 , iv)(Tear strength)	-	500	-
7.6 , Table No. 7 , v)(Tensile strength)	-	500	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	500	-
7.6 , Table No. 7 , vii)(Compression set)	-	300	-
7.7 , Table No. 8 , i)(Compression set)	-	400	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	500	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	400	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	500	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	600	-
7.8 , Table No. 9 , ii)(Resilience)	-	600	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	700	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	600	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	600	-
7.8 , Table No. 9 , v)(Peel strength)	-	800	-
7.9 , Table No. 10 , i)(Peel strength)	-	800	-
7.9 , Table No. 10 , ii)(Shear strength)	-	800	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	500	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	500	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	500	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	500	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	600	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	500	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	500	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	400	-
8(MARKING AND PACKING)	-	100	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	600	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	400	-
7.12.2 (Amendment 1)(Lead content)	-	400	-

31 Dec, 2026

-
-

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

12900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.16.2(Breaking Strength of lace )	-	500	-
4.16.1(Length of lace )	-	100	-
4.15(D-ring & Hooks )	-	0	-
6.1(Resistance to Fuel Oil)	-	500	-
4.14.9(Resistance to hot contact )	-	500	-
4.14.8(Flexing resistance )	-	600	-
4.14.7(Ageing test)	-	500	-
4.14.6(Hardness (IRHD))	-	400	-
4.14.5(Abrasion resistance )	-	800	-
4.14.4(Tear Strength)	-	500	-
4.14.3(Sole Density )	-	400	-
4.14.2(Thickness)	-	250	-
4.14.1(Material)	-	0	-
4.13(Breaking Strength of thread )	-	500	-
4.12.2(Tear Strength)	-	500	-
4.12.1(Thickness )	-	250	-
4.11.2(Tear Strength)	-	500	-
4.11.1(Thickness )	-	250	-
4.10.3(Water absorption & desorption percent)	-	600	-
4.10.2(Abrasion resistance )	-	700	-
4.10.1(Material)	-	0	-
4.9.3(Water absorption & desorption percent)	-	600	-
4.9.2(Abrasion resistance )	-	400	-
4.9.1(Thickness)	-	250	-
4.8(Thickness Toe puff & counter stiffener)	-	250	-
4.7.5(Water Vapour permeability & coefficient )	-	800	-
4.7.4(Abrasion resistance )	-	700	-
4.7.3(Tear Strength)	-	500	-
4.7.2(Material Counter & Tongue)	-	0	-
4.7.1(Material vamp & Quarter)	-	0	-
4.6.2(Tear Strength)	-	500	-
4.6.1(Thickness )	-	250	-
4.5.8(Energy absorption of seat region )	-	600	-
4.5.7(Cold Insulation of sole complex)	-	800	-
4.5.6(Heat Insulation of sole Complex)	-	700	-
4.5.5(Antistatic test)	-	500	-
4.5.4(Slip Resitance)	-	1200	-
4.5.3.2(Interayer bond strength)	-	600	-
4.5.3.1(Upper/outsole bond strength)	-	600	-
4.5.2(Ergonomic Feature)	-	0	-
4.5.1(Construction)	-	0	-
4.4(Height of upper )	-	200	-
4.3.2(Weight)	-	100	-
4.3.1(Size)	-	0	-
4.2(Design )	-	0	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2, 8.6 of IS 15298 part 1,ISO 1817,ISO 4643,(Resistance to fuel oil)	-	500	-
8, 8.1, 8.2, 8.2.1(Marking)	-	100	-
9(Information to be Supplied)	-	0	-
Cl.4.6.4(Water Penetration and Water Absorption)	-	500	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2,(Resistance to fuel oil)	-	500	-
4.6.3(Water Penetration and water absorption )	-	500	-
CL.8,8.1, 8.2,8.2.1(Marking)	-	100	-
Cl.9,(Information to be Supplied)	-	0	-

31 Dec, 2026

-
-

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

15700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	0	-
Cl 5.2.2, Table 4(" Height of upper ")	-	200	-
Cl 5.2.3(Heel area)	-	100	-
Cl 5.3.1.1(Construction of whole footwear)	-	100	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	600	-
Cl 5.3.2.1(Toe protection - general)	-	0	-
Cl 5.3.2.2(Internal length)	-	100	-
Cl 5.3.2.3(Width of toecap flange)	-	100	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	400	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	0	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	0	-
Cl 5.3.2.6(Impact resistance)	-	600	-
Cl 5.3.2.7(Compression resistance)	-	500	-
Cl 5.3.3(Leak proofness)	-	500	-
Cl 5.3.4("Specific ergonomic features ")	-	100	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1200	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	600	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	400	-
Cl 5.3.7(Seam strength)	-	500	-
Cl 5.3.8(Lead Content ( National Annex A))	-	400	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.2(Thickness)	-	250	-
Cl 5.4.3(Tear strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	500	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	500	-
Cl 5.4.5(Flexing resistance)	-	500	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	800	-
Cl 5.4.7(Resistance to hydrolysis)	-	2000	-
Cl 5.5.2(Lining- Tear strength)	-	500	-
Cl 5.5.3(Lining- Abrasion resistance)	-	700	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	800	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	500	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	100	-
Cl 5.7.2(Water permeability of insock)	-	600	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	600	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	400	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	700	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	250	-
Cl 5.8.2.2(Cleated area)	-	0	-
Cl 5.8.2.3(Cleat height)	-	100	-
Cl 5.8.3(Outsole- Tear strength)	-	500	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	800	-
Cl 5.8.5(Outsole-Flexing resistance)	-	600	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	2000	-
Cl 5.8.7(Interlayer bond strength)	-	600	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	500	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	500	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	500	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	0	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	0	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	400	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	0	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	0	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	700	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	700	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	700	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	800	-
Cl 6.2.4(Energy absorption of seat region)	-	600	-
Cl 6.2.5(Water resistance)	-	600	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	500	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	100	-
Cl 6.2.8.3(Resistance to cutting)	-	500	-
Cl 6.2.9(Scuff cap)	-	200	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	1200	-
Cl 6.3(Upper — Water penetration and absorption)	-	500	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	500	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	500	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	0	-
Cl 6.4.3.2(Design of Ladder grip)	-	0	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	100	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	100	-
Cl 7, Table 20("Marking ")	-	100	-

31 Dec, 2026

-
-

IS 5557 : Part 1 (2024)

All Rubber Gum Boots and Ankle Boots Part 1 Safety and Protective

10900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	-
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	100	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	500	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	500	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	400	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	400	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	500	-
8.5.2(Thickness)	-	100	-
8.5.3(Flexing Resistance)	-	600	-
8.5.4(Abrasion Resistance)	-	700	-
8.6.1(Thickness of Outsole)	-	200	-
8.6.2(Tear Strength)	-	500	-
8.6.3(Abrasion Resistance of Outsole)	-	800	-
8.6.4(Flexing Resistance)	-	600	-
8.6.5(Inter layer Bond Strength of outsole)	-	600	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	100	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	700	-
Cl-8.8.1(Outsole/Heel)	-	500	-
Cl-8.9(Leak Proof Test)	-	500	-
8.10(Height of Upper)	-	200	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	600	-
Cl-8.12(Upper Outsole Bond Strength)	-	600	-
Cl-8.13(Internal Length of Toe Cap)	-	200	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	700	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	600	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	1200	-
8.17(Steel Floor with Glycerine)	-	1200	-
8.18(Corrosion Resistant Test for Toe Caps)	-	400	-
9.1(Penetration Resistance)	-	500	-
9.2(Antistatic Footwear)	-	700	-
9.4(Electrical Resistance)	-	700	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	500	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	500	-
9.6(Resistance to Fuel Oil)	-	500	-
11.2(Marking)	-	100	-

31 Dec, 2026

-
-

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

10700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	400	-
3.3(compact insole)	-	400	-
3.4(compact Outsole/heel)	-	400	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	500	-
7.1.2(Abrasion resistance)	-	700	-
7.2(Coated bindind material)	-	500	-
7.3(Thread for upper closing)	-	500	-
7.3(Thread for upper closing - sulphur test)	-	400	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	700	-
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	500	-
7.5.2(Thickness)	-	100	-
7.5.3(Flexing Resistance)	-	600	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	200	-
7.6.2(out sole tear strength)	-	500	-
7.6.3(out sole abrasion)	-	800	-
7.6.4(out sole flexing)	-	600	-
7.6.5(Interlayer bond strength)	-	600	-
7.7(INSOCK Visual)	-	100	-
7.7.1(Insock thickness)	-	100	-
7.7.2(Insock abrasion)	-	700	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	500	-
8.2(Leak proofness)	-	500	-
8.3(Height of upper)	-	200	-
8.4(Adhesion test)	-	600	-
8.5(Resistance to acid & alkaline)	-	500	-
8.6(Resistance to fule oil)	-	500	-
8.7.1(Antistatic)	-	700	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	700	-
8.7.3(Elecrically nsulating footwear)	-	1000	-
8.7.4(Resistance to cold)	-	800	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	100	-
11.2(Marking)	-	100	-
11.3(Marking)	-	100	-

31 Dec, 2026

-
-

IS 13995 (1995)

Unlined moulded rubber boots - Specification

Unlined moulded rubber boots

2700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Size)	-	100	OK
5.1.6(Design)	-	0	OK
5.1.5(Flexing resistance of upper)	-	600	OK
5.1.4(Resistance to dry heat ageing )	-	500	OK
5.1.3(Tear Strength)	-	500	OK
5.1.2(Tensile Strength (after ageing))	-	500	OK
5.1.1(Tensile Strength (before ageing))	-	500	OK
4.1(Thickness )	-	250	OK
6, 6.1(Marking)	-	100	OK

31 Dec, 2026

-
-

IS 11544 (1986)

Specification for slipper, rubber

3800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.6(Thickness of components)	-	100	OK
3.2.5(Type of Thread)	-	500	OK
3.2.4(Picks per cm)	-	200	OK
3.2.4(End per cm)	-	200	OK
3.2.4(Mass per unit area)	-	400	OK
3.2(Flexural endurance)	-	1500	OK
3.2(Hardness after ageing)	-	500	OK
3.2(Hardness (IRHD))	-	400	OK
3.2(Relative density )	-	400	OK
3.1(Shape & Design)	-	100	OK
3.2.2(Bottom Filling Material)	-	100	OK
3.2.4.1(Weave of fabrics)	-	100	OK
3.2.7(vulcanized process)	-	100	OK
3.2.8(Workmanship and Finish -)	-	0	OK
3.2.9(Preservation -)	-	100	OK
Cl. 4, Cl. 4.1, Cl 4.2, Cl. 4.3(Marking and packing)	-	100	OK

31 Dec, 2026

-
-

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	0	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	400	OK
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	400	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	400	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	0	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	500	OK
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	0	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	600	OK
5, 5.1(Marking)	-	100	OK
6, 6.1(Packing)	-	0	OK
4.2(Size & Thickness )	-	250	OK
6, 6.1(Packing)	-	0	-
Cl.4.1.3 and 8.3,Table 1 ii(Thickness)	-	250	-
Cl.4.1.3 and 8.3,Table 1 vii(Abrasion resistance at applied force of 5 N)	-	800	-
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	0	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	300	OK
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	300	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	400	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	200	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	300	OK
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	200	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	700	OK
5, 5.1(Marking)	-	0	OK
6, 6.1(Packing)	-	-	-
Cl.4.1.3 and 8.3,Table 1 ii(Thickness)	-	-	-
Cl.4.1.3 and 8.3,Table 1 vii(Abrasion resistance at applied force of 5 N)	-	-	-

31 Dec, 2026

-
-

IS 6719 (1972)

Solid Pvc Soles And Heels

2100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	400	OK
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	OK
3.6 (i)(Relative density )	-	400	OK
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	600	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	800	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	400	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	400	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	400	-
Cl. 6.4(Measurement of thickness)	-	250	-

31 Dec, 2026

-
-

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	500	OK
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	0	OK
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	100	OK
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	250	OK
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	2300	OK
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	900	OK
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	600	OK
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	100	OK
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	0	OK
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	500	OK
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	500	OK
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	600	OK
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	400	OK
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	500	OK
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	600	OK
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	200	OK
6.1(Marking)	-	100	OK
6, 6.1(Packing)	-	0	OK

31 Dec, 2026

-
-

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-7(Freedom From Defects)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.1(Wires-Nominal Sizes)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.1(Joint in Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.2(Aluminium Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.3(Galvanized Steel Wires)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.3(Conductor- Visual examination)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.4(Aluminium wires-Measurement of diameter)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Aluminium wires -Breaking load test)	-	1285	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Aluminium wires- Wrapping test)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.4(Steel wires- Measurement of diameter)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Steel wires- Breaking load test)	-	215	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.7(Steel wires- Ductility test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Steel wires- Wrapping test)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.1(Torsion Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.2(Elongation Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.1.1(chemical composition of high carbon steel)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.2(zinc used for galvanizing)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.1(Standard Length)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.2(Random Lengths)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6(Material)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-7(Freedom From Defects)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.1(Wires-Nominal Sizes)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.1(Joint in Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.2(Aluminium Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.3(Galvanized Steel Wires)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.3(Conductor- Visual examination)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.4(Aluminium wires-Measurement of diameter)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Aluminium wires -Breaking load test)	-	1285	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Aluminium wires- Wrapping test)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.4(Steel wires- Measurement of diameter)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Steel wires- Breaking load test)	-	215	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.7(Steel wires- Ductility test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Steel wires- Wrapping test)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.1(Torsion Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.2(Elongation Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.1.1(chemical composition of high carbon steel)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.2(zinc used for galvanizing)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.1(Standard Length)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.2(Random Lengths)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6(Material)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-7(Freedom From Defects)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.1(Wires-Nominal Sizes)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.1(Joint in Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.2(Aluminium Wires)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-9.3(Galvanized Steel Wires)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.3(Conductor- Visual examination)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	400	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.4(Aluminium wires-Measurement of diameter)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Aluminium wires -Breaking load test)	-	1285	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Aluminium wires- Wrapping test)	-	600	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	700	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.4(Steel wires- Measurement of diameter)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.6(Steel wires- Breaking load test)	-	215	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.7(Steel wires- Ductility test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.8(Steel wires- Wrapping test)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.1(Torsion Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-13.7.2(Elongation Test)	-	550	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.1.1(chemical composition of high carbon steel)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-6.2(zinc used for galvanizing)	-	2000	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.1(Standard Length)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).
Cl-11.2(Random Lengths)	-	100	Other than exempted test: Rs 8000 (up to 80 sq mm), Rs13000(100 sq mm), Rs 33000 (130 sq mm), Rs 37000 (150 sq mm to 400 sq mm for 33 Strands), Rs 49000 (400 sq mm,520 sq mm,560 sq mm,690 sq mm for 49 Strands), Rs 61000 (420 sq mm,530 sq mm,810 sq mm).

31 Dec, 2026

-
Included w.e.f. 29.10.2025 "Cl- 13.14 (Conductor- Ultimate tensile strength test on stranded conductor) Cl- 13.13 (Conductor- Surface condition test on stranded conductor) Cl- 13.15 (Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.)) Cl-13.16 (Conductor- Radio interference voltage test)"

IS 2074 (2023)

Ready Mixed Paint Air Drying Red Oxide Zinc Chrome Priming -Specification (Fourth Revision)

All types

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(The smell of the material shall not be objectionable during application)	-	100	-
Cl-5.1 (a)(Pigment)	-	1000	-
Cl-5.1 (b)(Driers)	-	500	-
Cl-5.1.1 (a)("Zinc oxide content Chromic anhydride content")	-	2500	-
Cl-5.1.1 (b)(Synthetic red oxides of iron or Natural red oxides of iron or A mixture of both which shall correspond to red oxide, percent by mass)	-	2500	-
Cl-5.1.1 (c)(Suitable extenders)	-	500	-
Cl-5.1.2(volatile vehicle)	-	500	-
Cl-5.2(Material)	-	500	-
Cl-5.3(Compatibility with Thinner)	-	500	-
Cl-5.4(Freedom from Objectionable Impurities)	-	100	-
Cl-5.5(Lead Restriction)	-	1000	-
Cl-5.6 & 8 Table-1 (i) (a)(Consistency)	-	500	-
Cl-5.6 & 8, Table-1 (i) (b)(Viscosity by ford cup No. 4 at 27±2°C)	-	1000	-
Cl-5.6 & 8, Table-1 (ii)(Mass, in kg/10 1, Min)	-	1000	-
Cl-5.6 & 8, Table-1 (iii)("Drying time, h, Max a) Surface dry b) Hard dry")	-	500	-
Cl-5.6 & 8, Table-1 (iv)(a) Finish)	-	500	-
Cl-5.6 & 8, Table-1 (iv)(b) Gloss 60° , Max)	-	1000	-
Cl-5.6 & 8, Table-1 (v)(Fineness of grind, microns, Max)	-	1000	-
Cl-5.6 & 8, Table-1 (vi)(Colour)	-	500	-
Cl-5.6 & 8,, Table-1 (vii) a)(Flexibility and adhesion: Bend test with 6.25mm dia mandrel and in type 1 apparatus)	-	1500	-
Cl-5.6 & 8,, Table-1 (vii) b)(Flexibility and adhesion: Scratch hardness)	-	1500	-
Cl-5.6 & 8, Table-1 (viii)(Flash point)	-	2000	-
Cl-5.6 & 8,, Table-1 (ix)(Volume solids, percent)	-	1000	-
Cl-5.6 & 8,, Table-1 (x) (a)(Resistance to humidity)	-	3500	-
Cl-5.6 & 8, Table-1 (x) (c)(Resistance to salt spray)	-	8000	-
Cl-5.6 & 8, Table-1 (xi)(Accelerated storage stability test)	-	2500	-
Cl-5.6 & 8, Table-1 (xii)("Keeping properties Visual observation (Corrosion and odour of putrefaction, rancidity or souring) ")	-	1000	-
Cl-5.6 & 8, Table-1 (xii)("Keeping properties Change in skinning")	-	1000	-
Cl-5.6 & 8, Table-1 (xii)("Keeping properties Degree of settling ")	-	1000	-
Cl-5.6 & 8, Table-1 (xii)("Keeping properties Observation of dried film ")	-	1000	-
Cl-5.6 & 8, Table-1 (xii)("Keeping properties Loss of mass resulting from Storage ")	-	1000	-
Cl-5.7, Table-2 (i)(Consistency)	-	1000	-
Cl-5.7, Table-2 (ii)(Hard dry, h, Max)	-	1000	-
Cl-5.7, Table-2 (iii)(Non- volatile vehicle, percent, Min)	-	1000	-
Cl-5.7, Table-2 (iv)(Wet opacity, m2 /10 l, Min)	-	1000	-

31 Dec, 2026

-
Included w.e.f.01.09.2025 Exclusion Cl-5.6 & 8, Table-1 (x) (b) ("Resistance to sea water (applicable for marine paints only)")

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

All type

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	0	-
4.1(Sulphur and phosphorous)	-	0	-
4.1(CE)	-	0	-
Cl 7.2(Weight)	-	600	-
Cl 6.1(Length, Width & Thickness)	-	0	-
Cl 5(Deformations and Surface Characteristics)	-	8400	-
4.1(Ni)	-	500	-
4.1(Mo)	-	500	-
4.1(Cr)	-	500	-
4.1( Ti)	-	500	-
4.1(V)	-	500	-
4.1( Nb)	-	500	-
4.1( Aluminium %)	-	500	-
4.1( Copper %)	-	500	-
4.1(Silicon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Manganese %)	-	500	-
4.1(Carbon %)	-	500	-
Cl 9.4(Load In Other Direction From Bend)	-	500	-
Cl 9.3(Load In One Direction)	-	600	-
Cl 8.1(UTM)	-	1200	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1200	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	0	-
Cl. 8.1 Table 3(TS/YS ratio)	-	0	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1200	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	0	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	600	-
4.1( Nitrogen%)	-	600	-

31 Dec, 2026

-
-

IS 9537 : Part 8 (2003)

Conduits for electrical installations - Specification: Part 8 rigid non - Threadable conduits of aluminium alloy

Aluminum Alloy Conduit

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(type test)	-	0	Testing charges applicable per sample per size.
4.2(ambient temperature)	-	0	Testing charges applicable per sample per size.
4.5(for rigid conduits, lengths)	-	0	Testing charges applicable per sample per size.
4.5(for pliable and flexible conduit coils)	-	0	Testing charges applicable per sample per size.
7(DIMENSIONS)	-	4000	Testing charges applicable per sample per size.
8(CONSTRUCTION)	-	1000	Testing charges applicable per sample per size.
9.2(Bending Test)	-	1000	Testing charges applicable per sample per size.
9.3(Compression Test)	-	1000	Testing charges applicable per sample per size.
clause No. 9.1(replacement)	-	1000	Testing charges applicable per sample per size.
clause No. 12(ELECTRICAL CHARACTERISTICS)	-	1000	Testing charges applicable per sample per size.

31 Dec, 2026

-
Included w.e.f. 02.04.2024

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

All Type

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Freedom from Coarse Particles)	-	200	-
6.4(Skin Formation)	-	0	-
6.5(Thinning Properties)	-	0	Sample along with suitable thinner 1 L can be submitted
6.6(Application Properties)	-	0	-
6.8(Lead Restriction)	-	800	-
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-	200	-
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-	500	-
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-	500	-
6.9 Table 2 ( 2) Mass, (Finishing ) )	-	500	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-	1000	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-	200	-
6.9 Table 2 (b) Hard dry ( Under coating ) )	-	200	-
6.9 Table 2 (b) Hard dry, (Finishing ) )	-	200	-
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-	200	-
6.9 Table 2 (4) a) Finish (Under coating ) )	-	200	-
6.9 Table 2 (4) a) Finish (Finishing) )	-	200	-
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-	500	-
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-	500	-
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-	200	-
6.9 Table 2 (5) Fineness of grind,(Finishing))	-	200	-
6.9 Table 2 (6) Colour , (Finishing))	-	500	-
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-	500	-
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-	500	-
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-	1000	-
6.9 Table 2 (9) Composition: a) Volume solids ( Under coating ))	-	1000	-
6.9 Table 2 (9) Composition: a) Volume solids ( Finishing))	-	1000	-
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-	2000	-
6.9 Table 2 (10) Resistance to acid ( Under coating & Finishing ))	-	200	-
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-	1000	-
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-	1000	-
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-	500	-

31 Dec, 2026

-
Included w.e.f. 02.04.2024 Exclusion: Cl.6.7.1.3 (QUV appratus)

IS 653 (1992)

Linoleum Sheets And Tiles

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3-01-01(width of sheet)	-	200	-
5.3-01-02(Tolerance to tile size)	-	200	-
5.3-01-03(Thickness)	-	200	-
7("Squareness (for tiles only")	-	500	-
7(Seasoning (for plain linoleum only))	-	400	-
7(Residual Indentation)	-	1000	-
7(Flexibility)	-	500	-
7(Water absorption)	-	1000	-
7(Ageing)	-	1500	-
7("Colour fastness to day light")	-	1000	-

31 Dec, 2026

-
Included w.e.f. 28.03.2024

IS 15298 : part 4 (2017)

Personal protective equipment: Part 4 occupational footwear (Second Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(CLASS I)	-	0	OK
Table 1(CLASS II)	-	0	OK
5.2.2.1(General)	-	0	OK
5.2.2.2(Height of upper)	-	100	OK
5.3.2.1(Construction)	-	0	OK
5.3.1.2(Upper/outsole bond strength)	-	400	OK
5.3.2.2(Leakproofness)	-	300	OK
5.3.2.3(Specific ergonomic features )	-	0	OK
5.3.4.1(Slip resistance)	-	500	OK
5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (SLS) solution)	-	0	OK
5.3.4.3(Slip resistance on steel floor with glycerine )	-	0	OK
5.3.4.4(Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine )	-	0	OK
5.4.2.2(Thickness )	-	100	OK
5.4.2.3(Tear strenth)	-	400	OK
5.4.2.4(Tensile properties)	-	400	OK
5.4.2.5(Flexing resistance )	-	500	OK
5.4.2.6(Water vapour permeability and coefficient )	-	600	OK
5.5.2.4(pH value )	-	200	OK
5.5.2.5(Chromium VI content )	-	300	OK
5.4.2.8(Hydrolysis)	-	0	OK
5.5.2.1(Tear strength )	-	400	OK
5.5.2.2(Abrasion resistance )	-	500	OK
5.5.2.3(Water vapour permeability and coefficient )	-	0	OK
5.6.2.1(Tear strength )	-	0	OK
5.6.2.2(pH value )	-	0	OK
5.6.2.3(Chromium VI content )	-	0	OK
5.7.2.1(Insole and insock )	-	0	OK
5.7.2.2(Insole and insock )	-	0	OK
5.7.2.3(Water absorption and desorption )	-	500	OK
5.7.4.1(Abrasion resistance )	-	300	OK
5.7.4.2(Abrasion resistance )	-	300	OK
5.7.2.5(Chromium VI content )	-	0	OK
5.8.2.1(Outsole)	-	0	OK
5.8.1.1(Thickness )	-	100	OK
5.8.1.2(Cleated area )	-	0	OK
5.8.1.3(Cleat height)	-	0	OK
5.8.2.2(Tear strength )	-	400	OK
5.8.2.3(Abrasion resistance )	-	300	OK
5.8.2.4(Flexing resistance )	-	500	OK
5.8.2.5(Hydrolysis )	-	500	OK
5.8.2.6(Interlayer bond strength )	-	400	OK
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	300	OK
6.2.1.2(Construction)	-	0	OK
6.2.1.3(Dimensions )	-	0	OK
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	300	OK
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	0	OK
6.2.2.1(Conductive footwear)	-	0	OK
6.2.2.2(Antistatic footwear)	-	500	OK
6.2.3.1(Heat insulation of sole complex )	-	500	OK
6.2.3.2(Cold insulation of sole complex)	-	500	OK
6.2.2.4(Energy absorption of seat region )	-	400	OK
6.2.2.5(Water resistance )	-	0	OK
6.2.2.6(Ankle protection)	-	0	OK
6.2.7.1(Cut resistance foot wear)	-	500	OK
6.2.7.2(Cut resistance foot wear)	-	0	OK
6.3.2.2(Upper- water penetration)	-	300	OK
6.4.2.1(Resistance to hot contact)	-	300	OK
6.4.2.2(Resistance to fuel oil)	-	400	OK
5.2.2.3(Seat region)	-	0	OK
5.4.2.1(Upper)	-	0	OK
5.4.2.7(pH value )	-	0	OK
5.4.2.9(Chromium VI content )	-	0	OK
6.2.2.3(Electrically insulating footwear )	-	500	OK
6.2.7.3(Resistance to cutting)	-	0	OK
6.2.7.4(Pentration resistance)	-	0	OK
6.2.1.1(Metallic anti-penetration insert )	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion: Cl.6.2.1.4 (Flex resistance of penetration-resistant inserts ), Cl.5.3.2.5 (Innocuousness )

IS 15298 : Part 3 (2019)

Personal protective equipment: Part 3 protective footwear (Second Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2 Table-2(Height of upper)	-	0	-
5.3.1.1 Table-2(Construction)	-	0	-
5.3.1.2 Table-2(Upper/Outsole Bond)	-	400	-
Table-2(Strength)	-	0	-
5.3.2.1 Table-2(General)	-	0	-
5.3.2.2 Table-2(Internal Length of toe cap)	-	0	-
5.3.2.3 Table-2(Impact Resistance -T- )	-	400	-
5.3.2.4 Table-2(Compression)	-	400	-
5.3.3 Table-2(Leak Proofness)	-	300	-
5.3.5.2 Table-2(Slip Resistance SRA)	-	500	-
5.3.5.3 Table-2(Slip Resistance SRB)	-	500	-
5.3.5.4 Table-2(Slip Resistance SRC)	-	500	-
5.4.1 Table-2(General)	-	0	-
5.4.2 Table-2(Thickness)	-	100	-
5 4 3 Table-2(Tear Strength)	-	400	-
5.4.4 Table-2(Tensile Properties)	-	400	-
5.4.5 Table-2(Flexing Resistance)	-	500	-
5.4.6 Table-2(Water Vapour Permeability & Coefficient)	-	700	-
5 4.7 Table-2( )	-	200	-
5 4.8 Table-2(Hydrolysis)	-	500	-
5.4 9 Table-2(Chrome VI)	-	300	-
5.5.1 Table-2(Tear Strength)	-	400	-
5.5.2 Table-2(Abrasion Resistance)	-	500	-
5.5.3 Table-2(Water Vapour Permeability & Coefficient)	-	0	-
5.5.4 Table-2(pH Value)	-	200	-
5.5.5 Table-2(Chrome VI)	-	300	-
5.6.1 Table-2(Tear Strength)	-	0	-
5.6.2 Table-2(pH Value)	-	200	-
5.6.3 Table-2(Chromium VI)	-	300	-
5.7.3 Table-3(Water Absorption &)	-	500	-
Table-3(Desorption)	-	0	-
5.8.6 Table-2(Interlayer BondStrength)	-	400	-
6.2.1 Table-I8(Penetration Resistance)	-	300	-
6.2.2.1 Table-18(Electrical Properties)	-	500	-
6.2.2.2 Table-18(Antistatic Footwear)	-	500	-
6.2.3.1 Table-18(Heat Insulated Comp)	-	500	-
6.2.3.2 Table-18(Cold Insulated)	-	500	-
6.2.4 Table-18(Energy Absorption of seat region)	-	400	-
6.2.5 Table-18(Water Resistance)	-	200	-
6.2.7 Table-18(Ankle Protection)	-	500	-
6.2.8 Table-18(Cut Resistance)	-	500	-
6.3 Table-18(Water Penetration & Absorption)	-	300	-
6.4.1 Table-18(Resistance to Hot Contact)	-	300	-
6.4.2 Table-18(Resistance to Fuel oil)	-	400	-
8.2.1(Conductive footwear)	-	500	-
8.2.2(Antistatic footwear)	-	500	-

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Excluding Footwear with electrical insulating

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

Insulation A,C,D/Sheath ST1,ST2,ST3/Cat 01,02,FR/AYY

20000 View breakup
Type Test: Rs.10000/- (1 core), Rs.11000/- (2 core), Rs.13000/- (3 core), Rs.15000/- (3 1/2, 4 core) Optional Tests Cold Bend test – Rs 1500 /- Cold Impact – Rs 1500 /-Additional Ageing Test – Rs 1500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3000	-
10.4(Flammability test- Unaffected portion)	-	500	-
10.4(Flammability test-Burning after flame removal)	-	500	-
table 1 e) 3) (IR constant- max. Temp)	-	250	-
table 1 e) 3) (IR constant- Room temp )	-	250	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	250	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	250	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	750	-
10.1(HV (water immersion))	-	750	-
10.6(Halogen evolution)	-	5000	-
10.7(Temperature index)	-	5000	-
10.5(Oxygen index)	-	5000	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	500	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	500	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	500	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	-
Table 1 iii) d) 4)(Cracks Observed)	-	500	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500	-
Table 1 iii) c) 4)(Cracks Observed)	-	500	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	625	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	625	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	625	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	625	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	625	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	625	-
Table 1 iii) c) 3)(Elongation variation)	-	625	-
Table 1 iii) c) 3)(TS variation)	-	625	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	625	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	625	-
8.3(Thickness of Sheath)	-	500	-
5.3(Thickness of Insulation)	-	500	-
9.1(Ovality)	-	500	-
9(Overall dimensions)	-	500	-
4.2(Conductor resistance test)	-	500	-
4.1(Wrapping test (for Al))	-	400	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
4.1(Annealing test (for copper))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
8.3(Minimum thickness of Sheath)	-	250	-
8.3(Avarage thickness of Sheath)	-	250	-
5.3(Minimum thickness of insulation)	-	250	-
5.3(Avarage thickness of insulation)	-	250	-
11.1(Durability)	-	500	-
13(Cable code)	-	500	-
11.2(Legibility)	-	500	-
11(Identification)	-	500	-
Table 1(Category Code)	-	500	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	500	-
5.2(Application )	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
8.1(Sheath Material )	-	500	-
7(Binder Tape)	-	500	-
6.2(Filler)	-	500	-
6.1(Filler)	-	500	-
5.1(Insulation)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.1(Conductor - Material)	-	500	-
4.1(Conductor - Material)	-	500	-
12.0(Core identification)	-	500	-
4, IS 8130(Construction of conductor)	-	500	-
Table 2, IS 8130(No fo wire in a conductor)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	500	-
Table 4(Copper purity test)	-	660	-
5.4(Mechanical properties before and after ageing)	-	2500	-

31 Dec, 2026

-
Exclusion: Cl.10.8 (smoke density rating), Cl.10.3 (spark test)

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

XLPE Insulated/ST2 PVC Sheathed/A2XFY/A2XWY/FR

22000 View breakup
Type test: Rs.11000/- or Rs.6000/- for two core, Rs.13000/- or Rs.7000/- for three core, Rs.15000/- or Rs.8500/- for 3.5 & 4 core, Optional Test Cold bend test – Rs 1500 /- Cold impact test – Rs 1500 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.1 a) i)(Annealing Test ( For copper wire ) )	-	500	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	400	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	400	-
15.1 a) iii)(Wrapping test (for aluminium))	-	400	-
15.1 a) iv)(Resistance test - Main conductor)	-	250	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	250	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	500	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	500	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	500	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	2500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	500	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	250	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	250	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	625	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	625	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	625	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	625	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	500	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	500	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	500	-
16.9(Oxygen Index Test)	-	5000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	500	-
15.4 (b)(Cold impact)	-	500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	625	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	625	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	625	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	625	-
Table 4(Copper purity test)	-	660	-
Table 2(Cold Impact test for Outer sheath)	-	500	-
Table 2(Cold bend test for Outer sheath)	-	500	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	500	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	500	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	500	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	500	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	500	-
14.3(Thickness of outer sheath - minimum)	-	500	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-

31 Dec, 2026

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

1100V/Type A/C/ST1/ST2/AYFY/AYWY/CAT01

15000 View breakup
Type test: Rs.14000/- (2 core), Rs.17000/- (3 core), Rs.19000/- (3 1/2, 4 core) Optional Tests Cold Bend test – Rs 1500 /- Cold Impact – Rs 1500 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	500	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
6.1(MATERIALS : ARMGURING)	-	500	-
6.2(MATERIALS : ARMGURING)	-	500	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	500	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.1(INSULATION )	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	250	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	250	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
10.3.1(Arrangement of Marking)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(ARMOURING : Direction of lay )	-	500	-
13.1.4(ARMOURING : Application)	-	500	-
13.2(ARMOURING : Type of Armour)	-	500	-
13.2.1(ARMOURING : Type of Armour)	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	500	-
13.5.1(ARMOURING : Resistance)	-	250	-
13.5.2(ARMOURING : Resistance)	-	250	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	500	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	500	-
14.2(OUTER SHEATH)	-	500	-
14.3(OUTER SHEATH : Colour )	-	500	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	500	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	500	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	400	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	400	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	400	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	250	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	250	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	250	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	250	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	250	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	250	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	625	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	625	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	625	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	625	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	625	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	625	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	625	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	625	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	500	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	500	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	500	-
15.1 d)6)(Heat shock test- Insulation )	-	500	-
15.1 d)6)(Heat shock test- sheath )	-	500	-
15.1 d)7)(Thermal stability- insulation )	-	500	-
15.1 d)7)(Thermal stability- Sheath )	-	500	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 e)(Insulation resistance test : IR Constant )	-	500	-
15.1 f)(High voltage test ( water immersion test ))	-	1500	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	500	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	500	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1500	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1500	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	5000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	500	-
17.2(IDENTIFICATION : Cable Identification)	-	500	-
17.2.1(IDENTIFICATION : Cable Identification)	-	500	-
17.3(IDENTIFICATION : Cable Code)	-	500	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	500	-
16.4(Flammability Test- Period of Burning)	-	500	-
9.3(Minimum Thickness of Reduce core insulation)	-	500	-
9.2(Thickness of Reduce core insulation)	-	500	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	500	-
Table 4(Copper purity test)	-	660	-

31 Dec, 2026

-
Exclusion: Cl.16.10 smoke density test, Cl.16.8 (Test for specific optical density & smoke)

IS 15298 : Part 2 (2016)

Personal protective equipment: Part 2 safety footwear (Second Revision)

13500 View breakup
-

Clause No.	Exclusion	Remark
4,Table 1(Class I, IS 15298)	-	NIL
4,Table 1(Class II, IS 15298)	-	NIL
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	NIL
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	NIL
5.2.3, Table 10 ,Design A(Seat Region)	-	NIL
5.3.1.1(Construction)	-	NIL
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	NIL
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	NIL
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	NIL
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	NIL
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	NIL
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	NIL
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	NIL
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	NIL
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	NIL
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	NIL
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	NIL
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	NIL
5.4.1,Table 10(General)	-	NIL
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	NIL
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	NIL
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	NIL
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	NIL
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	NIL
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	NIL
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	NIL
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	NIL
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	NIL
5.6(Tongue - IS 15298 Part 2 )	-	NIL
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	NIL
5.6.2(Ph Value ; ISO 20344,6.9)	-	NIL
5.6.3(Chromium VI content; ISO 17075)	-	NIL
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	NIL
5.7.2(Ph Value ; ISO 20344,6.9)	-	NIL
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	NIL
5.7.4.1(Insole ; ISO 20344,7.3 )	-	NIL
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	NIL
5.8.1.2(Cleated area)	-	NIL
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	NIL
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	NIL
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	NIL
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	NIL
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	NIL
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	NIL
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	NIL
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	NIL
6.2.1.2(Consruction)	-	NIL
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	NIL
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	NIL
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	NIL
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	NIL
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	NIL
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	NIL
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	NIL
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	NIL
6.2.6.1(Construction)	-	NIL
6.2.6.2 , Table 19(Impact resistance of metatarsal protective device,ISO 20344 , 5.16)	-	NIL
6.2.7 (Ankle protection ; ISO 20344 , 5.17)	-	NIL
6.2.8.1(Design)	-	NIL
6.2.8.2(Construction)	-	NIL
6.2.8.3,EN 388(Resistance to cutting ,EN 388)	-	NIL
6.2.8.4(Penetration Resistance)	-	NIL
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	NIL
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	NIL
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	NIL
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	NIL

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion: Cl.6.2.1.4 (Flex resistance of penetration -resistant insert ; ISO 20344,5.9), Cl.5.3.6 (Innocuousness)

IS 2581 (2002)

Round strand galvanized steel wire ropes for shipping purposes - Specification (Fourth Revision)

8150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon- IS 228)	-	500	50 grams chips
6.1(Manganese - IS 228)	-	500	50 grams chips
6.1(Silicon - IS 228)	-	500	50 grams chips
6.1(Sulphur - IS 228)	-	500	50 grams chips
6.1(Phosphorus - IS 228)	-	500	50 grams chips
6.1(Copper-IS 228)	-	500	50 grams chips
6.1(Nickel - IS 228)	-	500	50 grams chips
6.1(Chromium - IS 228)	-	500	50 grams chips
6.1(P + S - IS 228)	-	0	NIL
7,11.2 as per IS 1835 (Uniformity of Zinc Coating-IS 2633)	-	1000	2 metre
7,11.3 as per IS 1835 (Mass of Zinc Coating-IS 6745)	-	1500	2 metre

31 Dec, 2026

-
-

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

All grades

9720 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Thickness of sheet/strip)	-	0	Nil
6(Depth of bowl)	-	0	Nil
6(Internal dimensions of the bowl)	-	0	Nil
6(Bowl locating limits)	-	0	Nil
6(Co-ordinating sizes)	-	0	Nil
7.1(Consruction and workmanship)	-	600	Nil
7.1.1(Consruction and workmanship)	-	0	Nil
7.2(Consruction and workmanship)	-	0	Nil
7.2.1(Consruction and workmanship)	-	600	Nil
7.3(Drainers)	-	600	Nil
7.4(Waste outlet)	-	0	nil
7.5(Tap holes)	-	0	Nil
7.6(Overflows)	-	0	Nil
8(Finish)	-	600	Nil
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	500	Sample Size 30X50mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	500	Sample Size 30X50mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	500	ample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	500	ample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	500	ample Size 30X100mm sheet

31 Dec, 2026

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

All Type

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	1000	For 6 Conductors
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	1000	for Steel Wire (7 or 1)
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	400	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	400	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	800	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1600	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1600	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1600	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	600	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	500	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1300	-
13.7.2 (elec)(Mass of Zinc coating)	-	700	-

31 Dec, 2026

-
Exclusion: Cl.13.9 (Surface condition test), Cl.13.10 (ultimate breaking load), Cl.13.11 (Stress strain test)

Bureau of Indian Standards

The National Standards Body of India

MSME TESTING CENTRE, CHENNAI

65/1, GST Road, Guindy, Chennai, Chennai, Tamil Nadu, 600032

9445662299 dctc-sr@dcmsme.gov.in

Scope List