BIS - LIMS (Laboratory Information Management System)

CIPET, Hajipur

INDUSTRIAL AREA, Hajipur, Vaishali, Bihar, 844102

7781020335 testing-hajipur@cipet.gov.in

Scope List

Reset

16 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

38725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1 (Visual and Workmanship Requirement)	-	300	-
6.2, 6.2.1 (Quick Coupled Fittings)	-	6750.0	Density : 1000 (5002) Melt Flow Rate: 2200 (11002) Carbon Black Content: 1850 (9252) Carbon Black Dispersion:1400 (7002) Workmanship & Appearance: 300
6.1.3.2 (Quick coupled fittings)	-	0.0	-
6.1.3.1.1(Weldability Test)	-	6400.0	Acceptance Test: 1600 Quality Test: 4800
6.1.3, 6.1.3.1(Weldability Test)	-	0.0	-
6.1.2.2( Hydraulic Proof Test)	-	850.0	-
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	850.0	-
6.1(Quick Coupled Pipes and Fittings)	-	0.0	-
5.3(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500.0	-
5.2(Dimensions of Quick Coupled Pump Connectors Table 3.)	-	0.0	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	0.0	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0.0	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	0.0	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	0.0	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	0.0	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	0.0	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	0.0	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	0.0	-
4.1.5(Rubber Ring)	-	4950.0	Hardness before Ageing: 375.0 Ageing : 4200.0 Hardness after Ageing: 375.0
4.1.4(b)(Holding Attachments for Coupler Parts)	-	0.0	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	0.0	-
4.1 .3(Workmanship and Appearance)	-	300.0	-
4.1 .1.2.2(HDPE couplers)	-	0.0	-
4.1 .1.2.1(HDPE couplers)	-	0.0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700.0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.1 (b)(HDPE couplers —)	-	0.0	-
4.1 (a)( Quick Coupled Male and Female Couplers)	-	0.0	-
4(QUICK COUPLED FITTINGS)	-	0.0	-
3(QUICK COUPLED PIPES)	-	17575.0	-
Cl.6.1.3(Weldability Test- b) Acceptance test)	-	1600	-
Cl.6.1.3(Weldability Test- a) Quality test)	-	4800	-
Cl 4.1.5(Rubber rings- C)Rubber ring shall be of black colour:)	-	300.0	-
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	375	-
Cl 4.1.4(Holding attachments for coupler parts)	-	1700.0	850+850
Cl.4.1.3(Workmanship and appearance )	-	300.0	-
Cl.4.1(Quick Coupled Male and Female Couplers)	-	0.0	-

07 Oct, 2028

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

31869.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000.0	Testing Charges - 5500.0 Specimen Charges - 500.0
8.9 table-6(Elongation at Break)	-	1600.0	Testing Charges - 1100.0 Specimen Charges - 500.0
8.8(Tensile Strength for Butt-fusion)	-	1600.0	Testing Charges - 1100.0 Specimen Charges - 500.0
8.7(Density)	-	500.0	Nil
8.5 (Oxidation Induction Time)	-	2200.0	Nil
8.4( Melt Flow Rate)	-	1100.0	Nil
8.2(Longitudinal Reversion Test)	-	900.0	Testing Charges - 700.0 Specimen Charges - 200.0
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600.0	Nil
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400.0	Nil
7.4.1.2(Ovality)	-	0.0	Charges included in Dimension Test
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	500.0	Dimension of Pipe (MOD, Ovality, Thickness, Length)
7.2(Length)	-	0.0	Charges included in Dimension
6.2.1(6.1.1 Identification Stripes)	-	250.0	Nil
6.2(Colour)	-	250.0	Nil
8.6(Overall migration)	-	2000.0	Testing Charges - 1700.0 Specimen Charges - 300.0
8.3(Carbon black)	-	1625.0	CBC - 925 CBD - 700

07 Oct, 2028

-
-

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

7463 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1050	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.1 (chem)(Workmanship and Finish)	-	500	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.2 (chem)(Design, Shape & Dimension)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.3(Workmanship, Finish & Appearance)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.4 , clause 5 of IS:2798:1998(Brimful capacity in ml)	-	500	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.5, IS:2798:1998(Wall thickness- Bottom, in mm)	-	500	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.5, IS:2798:1998(Wall thickness- Middle , in mm)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.5, IS:2798:1998(Wall thickness- Top , in mm )	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.2(TRANSPARANCY)	-	700	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.3(LEAKAGE TEST)	-	1000	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.4(DROP TEST)	-	1100	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.5(MIGRATION TEST)	-	1700	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.6(PORTABILITY TEST)	-	2900	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.6 (chem)(Water Potability test (after 30 days) (a) Taste (b) Odour)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.5.1 (chem)(Colour migration (Caps))	-	0	Nil
4.6.5.1 (chem)(Colour migration (Container))	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.5 , IS:9845:1998 (chem)(Migration of Caps - a. Amount of extractive)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.5 , IS:9845:1998 (chem)(Migration- b. Amount of extractive)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.5 , IS:9845:1998 (chem)(Migration- a. Amount of extractive)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.3, clause 6 of IS:2798:1998(Leakage test- c. Air pressure leakage)	-	0.0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.3, clause 6 of IS:2798:1998(Leakage test- b. Vibration leakage)	-	0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.
4.6.3, clause 6 of IS:2798:1998(Leakage test- a. Closure leakage )	-	0.0	25% discount of test charges for BIS test assignment on proposed testing charges. Excluding specimen preparation & conditioning charges.

07 Oct, 2028

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

19380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material Identification)	-	1050	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1100	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	850	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	900	-
3.2(Unlaminated Fabric Mass )	-	250	-
3.3.1(Bottom seam (IS 10789))	-	250	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	-
4.2 and Table 1 ii(Dimensions )	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
4.2 and Table 1 v(Mass of sack )	-	250	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	2200	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	-
4.2 and Table 1 x(Ash content )	-	950	-

07 Oct, 2028

-
-

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

19140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	-
3.2(Tapes – Width )	-	250	-
3.2(Tapes – Linear Density )	-	0.0	-
3.3(Tying Cord)	-	0.0	-
3.4(Sack)	-	0.0	-
3.4.1(Seam)	-	250	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	250	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	250	-
4.1 and Table 1 ii(Ends per dm )	-	250	-
4.1 and Table 1 iii(Picks per dm )	-	250	-
4.2 and Table 1 iv(Mass of sack )	-	300	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	1100	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	1100	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12540	-
4.1 and Table 1 ix(Ash content )	-	950	-

07 Oct, 2028

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

19480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	-
4.2(Construction)	-	0	-
4.3.1(Bottom Seam)	-	250	-
4.3.1( The two rows of stitches shall be separated from each other)	-	250	-
4.3.1( The outer stitch)	-	250	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	250	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	250	-
4.3.1(The number of stitches/dm)	-	250	-
4.3.2(Mouth)	-	250	-
4.4 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v(Mass of sack )	-	250	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1100	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	1100	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	-
5.2 and Table 1 x(Ash content )	-	950	-

07 Oct, 2028

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	300	-
5.1.2(Film Form)	-	300	-
5.1.3(Odour)	-	300	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	-
5.1.6a(Carbon Black Content, Annex-A)	-	925	-
5.1.6b(Ash Content, Annex-A)	-	950	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	-
5.2.2(Tolerance on Thickness, Annex-A)	-	250	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1100	-
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	-
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1100	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1100	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1100	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1000	-
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1000	-
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1100	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1100	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	1100	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	1100	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	1100	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
8.1, Table 3(Tear resistance , Annex B)	-	2000	1500+500
8.1, Table 3(Puncture resistance , Annex C)	-	1350	1100+250
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	-
9.1, Table 4(Tear resistance , Annex B)	-	2000	1500+500
9.1, Table 4(Puncture resistance , Annex C)	-	1350	1100+250
Clause 9.1 (Table 4)(Break Elongation)	-	1100	-
Clause 9.1 (Table 4)(Yield Elonation)	-	1100	-
Clause 9.1 (Table 4)(Break strength)	-	1100	-
Clause 9.1 (Table 4)(Yield strength)	-	1100	-
Clause 8.1(Table 3)(Break Elongation)	-	1100	-
Clause 8.1(Table 3)(Break strength)	-	1100	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	1100	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1100	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1100	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1100	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1100	-
Clause 5.2.3(Tolerance on Width)	-	250	-

07 Oct, 2028

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

9725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	250.0	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (b)Tolerance on OD)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	250	Dimension All - 250 (OD, Wall Thickness, Tolerance etc)
6.0 (6.1) (Visual appearance)	-	300.0	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000.0	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000.0	-
8.0 (8.1) (Supply of pipes )	-	0.0	Charges include in visual Appearance
9.0 (9.1)(Coiling )	-	0.0	Charges include in visual Appearance
9.0 (9.1)(Minimum Internal Diameter of Coil)	-	0.0	Charges include in Dimension
3.1(Class of Pipe)	-	0.0	Charges include in visual Appearance
6.1(Visual Appearance)	-	300.0	-
7.2(Reversion Test)	-	1000	Testing Charges - 700 Specimen Charges - 300 Total Charges - 1000
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0.0	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0.0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200.0	0.0
7.3(Elongation at Break)	-	1350.0	Testing Charges - 1100 Specimen Charges - 250 Total Charges - 1350 Charges include for tensile test
7.3(Tensile Test)	-	0.0	Charges include in Elongation at Break
4.3(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	700	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	-
4.1.c.i (Density)	-	1125	Testing Charges - 500 Specimen Charges - 625

07 Oct, 2028

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

17150.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925.0	-
4.2.3(Carbon Dispersion Test)	-	700.0	-
5(Types and Features )	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	3050.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	3050.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0.0	-
5.3(Types and Features )	-	0.0	-
5.6(Types and Features )	-	0.0	-
6.1(Finish)	-	300.0	-
7.1.1(Resistance to Deformation)	-	700.0	-
7.1.2(Resistance to Deformation)	-	700.0	-
7.2(Resistance to Impact)	-	1100.0	-
7.3(Test for Top Load Resistance)	-	900.0	-
7.4(Tensile Strength)	-	1350.0	1100+250(Specimen Charges)
7.5(Flexural Modulus)	-	1600.0	1100+500 (Specimen Charge)
7.6(overall Migration)	-	2200.0	1700+500 (Specimen Charges)
9.2.1(Man-Hole and Hand-Hole Lids)	-	1050.0	-
9.2(Man-Hole and Hand-Hole Lids)	-	0.0	-
9.1(Man-Hole and Hand-Hole Lids)	-	250.0	-
9.1(Lid Thickness)	-	250.0	-
7.3(Test for Top Load Resistance)	-	900.0	-
6.1(Finish)	-	300.0	-
5.4(Wall Thickness above effective height)	-	250.0	-
5.2 Table 2 (7)(Minimum Wall Thickness)	-	250.0	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500.0	-

07 Oct, 2028

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

11475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	300	Including Visual appearance, color Designation)
3(Designation)	-	0.0	Include in Marking
4(Colour)	-	0.0	Include in Marking
6(Dimensions of pipes)	-	250.0	-
7(Visual Appearance)	-	0.0	Include in Marking
8.1(Hydraulic characteristics)	-	6400.0	a) Acceptance Test - 1600 b) Type Test - 4800
8.2(Reversion)	-	700	Testing Charges - 700 Specimen Charges - 300
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	-

07 Oct, 2028

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

19175 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3(CLASSIFICATION OF PIPES)	-	0	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1125	625 + 500
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.3(Anti-oxidant)	-	1100	-
5.1 table -1(DIMENSIONS OF PIPES)	-	500	-
5.1.2(Ovality)	-	0	-
6.1(VISUAL APPEARANCE)	-	300	-
7.1 Table -2(Hydraulic Characteristics)	-	0.0	-
7.2(Reversion Test)	-	1000	700 + 300 (specimen charges)
7.3(Tensile Test)	-	1350	1100 + 250 (specimen charges)
7.4table-2(Fusion Compatibility Test)	-	6400	-
7.5(Density)	-	500	-
7.6(Melt now Rate (MFR))	-	1100	-
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	700	-
(Cl.4.2)(Carbon black- a)carbon content)	-	925	-
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	-
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	4800	-
Cl.7.3(Tensile Test - ii)Elongation at Break)	-	1350	1100 + 250 (specimen charges)
Cl 7.1(Hydraulic Characteristics - Acceptance test)	-	1600	-
Cl 7.1(Hydraulic Characteristics - Quality test)	-	4800	-
Cl.6(Visual Appearance)	-	300	-
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	0	-
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	0	-
Cl.5(Dimensions of pipe - i) Outside diameter)	-	0	-

07 Oct, 2028

-
-

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

42280 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	1050	25% discount for BIS.
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	1000	Fabric Construction - Rs 500 Tape Width - Rs 500 25% discount for BIS.
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	500	Width of the Tape - Rs 500 25% discount for BIS.
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	500	25% discount for BIS.
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	500	25% discount for BIS.
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	25% discount for BIS.
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	2700	Avg. breaking strength of Fabric (min) a. Length wise Rs 1100 b. Width wise Rs 1100 Specimen Preparation - Rs 500 25% discount for BIS.
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	500	25% discount for BIS.
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	0	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1200	Ash Content Rs 1200 25% discount for BIS.
5.3(Lamination)	-	2050	Mass of lamination film Rs 500 Total Mass of Laminated woven fabric Rs 500 Material Identification of lamination Rs 1050 25% discount for BIS.
5.4(Sack Fabrication)	-	1500	Sacks Construction Rs 500 Gromet construction & dimensions Rs 1000 25% discount for BIS.
5.5(Capacity)	-	500	Capacity Rs 500. 25% discount for BIS.
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	1500	Inside dimensions a) Bottom panel (L × W), mm Rs 500 b) Open top (L × W), mm Rs 500 c) Height (H), mm Rs 500 25% discount for BIS.
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	0	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	0	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	0	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	2200	"Breaking strength before UV Exposure (min) a) Length wise " 1100 b) Width wise 1100 25% discount for BIS.
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.4(UV Resistance Test)	-	10180	UV Resistance(192 hrs)* 8 hour at 60°C Light cycle without condensation, 4 hour at 50°C Dark cycle with condensation, Irradiance 0.63 W/m2 (100 x 60 +92 x40) Specimen / Conditioning * - Rs 10180
7(PRINTING, PACKAGING AND MARKING)	-	0	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	4450	Identification (Chemical Analysis) Rs 1050 Melt flow rate (MFR) Rs 1100 Linear Density Rs 700 Tanacity Rs 1100 Elongation of the Tape & Thickness of the Tape Rs 500 25% discount for BIS.
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	1900	Dimensional Stability (100 °C & 10 min.) Rs 700 Dimensional Stability (125 °C & 10 min.) Rs 700 GSM of Unlaminated fabric Rs 500 25% discount for BIS.
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	3750	Stitches Separation (Min), Outer stitches (Min) Depth of seam over doubled fold (Min) Rs 500 No Stitches per dm Rs1100 Bottom seam Construction Rs500 Stitching thread material Identification Rs1050 Breaking load of stitching thread Rs1100 25% disc
Clause 7.3(Marking on Sacks)	-	2000	Presence of UV stabiliser : Rs 2000 25% discount for BIS.
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	2700	Breaking strength after UV Exposure (min) a) Length wise " Rs 1100 b) Width wise Rs 1100 Specimen Preparation: Rs 500 25% discount for BIS.
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

07 Oct, 2028

-
Included w.e.f. 22.08.2024

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

38230 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	500	25% discount for BIS.
5.2 Table 1(Dimensions)	-	500	25% discount for BIS.
5.2 Table 1(Dimensions)	-	2900	Thickness of the Tape Width of the Tape Dimensional Stability (100 °C & 10 min.) Dimensional Stability (125 °C & 10 min.) Weight of fabric (unlaminated) 25% discount for BIS.
5.2 Table 1(Dimensions)	-	3150	Tape Width Mesh size Identification Melt flow rate (MFR) 25% discount for BIS.
5.2 Table 1(Dimensions)	-	2500	Linear Density of tape Tanacity & Elongation Density of tape Raw Material 25% discount for BIS.
5.2 Table 1(Ends per dm)	-	500	25% discount for BIS.
5.2 Table 1(Picks per dm)	-	500	25% discount for BIS.
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	1050	4.1 Raw Material identification Rs 1050 25% discount for BIS.
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	2700	Avg. breaking strength of Fabric & Elongation Length wise & Width wise 25% discount for BIS.
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1100	Minimum breaking strength of Bottom seam 25% discount for BIS.
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1600	Breaking Load of stitching thread 25% discount for BIS.
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	2700	Breaking strength of fabric after 192 hrs of UV exposure length wise &Width wise 25% discount for BIS.
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	Already Included
5.2 Table 1(Drop impact strength)	-	1600	25% discount for BIS.
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	1200	Ash content 25% discount for BIS.
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	0	25% discount for BIS.
4.6(Capacity)	-	500	Sacks 25% discount for BIS.
4.3.1(Bottom Seam)	-	1500	1. Snitches Separation (Min) 2. Outer stitches (Min) 3. Depth of seam over doubled fold (Min) 25% discount for BIS.
4.3(Sacks)	-	0	25% discount for BIS.
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	3550	Bottom Seam –No Stitches per dm Stitching thread (Material Identification) Presence of UV stabiliser in stitching thread 25% discount for BIS.
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	10180	Specimen Charge Breaking strength of fabric after 192 hrs of UV exposure[UV Resistance(192 hrs)*8 hour at 60°C Light cycle without condensation, 4 hour at 50°C Dark cycle with condensation,Irradiance 0.63 W/m2 (100 x 60 +92 x40)] 25% discount for BIS.
4.2(Linear Density)	-	0	25% discount for BIS.
4.2(Width of tape)	-	0	Already Included

07 Oct, 2028

-
Included w.e.f. 22.08.2024

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

24150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	500	25% Discount for BIS.
4.1.2(Sack Width)	-	0	25% Discount for BIS.
4.1.3(Top Closure Width and Bottom Closure Width)	-	500	Fabric Construction.25% Discount for BIS.
4.1.4(Patch Length)	-	0	-
4.1.5(Patch Height)	-	0	-
4.1.6(Length of Valve)	-	2150	Identification (Chemical Analysis) Melt flow rate (MFR) 25% Discount for BIS.
4.1.7(Width of Valve Sleeve)	-	1100	Tanacity Elongation of the Tape 25% Discount for BIS.
4.1.8(Length of Valve Sleeve)	-	1500	Sacks Construction Construction of top & bottom closures Filling valves construction 25% Discount for BIS.
5.1(Raw Material)	-	1050	25% Discount for BIS.
5.2(Fabric)	-	2400	Thickness of the Tape Width of the Tape Dimensional Stability (100 °C & 10 min.) Dimensional Stability (125 °C & 10 min.) 25% Discount for BIS.
5.2(Tape density and width)	-	700	Linear Density.25% Discount for BIS.
5.4(Lamination for PP)	-	1550	mass of lamination film & Material Identification of lamination .25% Discount for BIS.
5.4(Lamination for LDPE)	-	1000	Total mass of laminated woven fabric& Overhung width. 25% Discount for BIS.
6.1(Mass of Bale)	-	500	25% Discount for BIS.
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	2700	Length Wise (Rs 1100) & Width Wise (Rs 1100) Specimen Preparation (Rs 500). 25% Discount for BIS.
6.2.2(Weld Strength of Top and Bottom Closures)	-	1100	25% Discount for BIS.
6.3(Drop Impact Testing of Filled Sacks)	-	1100	25% Discount for BIS.
6.4(Ash Content)	-	1200	25% Discount for BIS.
6.5(Air Permeability)	-	1100	25% Discount for BIS.
8(Atomspheric Conditions for Conditioning and Testing)	-	500	Perforation Construction.25% Discount for BIS.
Cl-5.6(Capacity)	-	500	25% Discount for BIS.
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	500	25% Discount for BIS.
Cl-6.6, Table-1 (iii)(Picks per dm)	-	500	25% Discount for BIS.
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	2000	Dimensions: Sack, Closure, Patch and Valve, in mm. 25% Discount for BIS.

07 Oct, 2028

-
Included w.e.f. 22.08.2024

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

26300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500	25% Discount for BIS
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500	25% Discount for BIS
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	500	25% Discount for BIS
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	Already Included.
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	Already Included.
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	Already Included.
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	Already Included.
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	500	Visual. 25% Discount for BIS.
4.1(Raw Material )	-	1050	25% Discount for BIS.
4.2 (Fabric)	-	500	Fabric Construction. 25% Discount for BIS.
4.2 (Linear Density, 900 denier)	-	700	25% Discount for BIS.
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	500	25% Discount for BIS.
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	Already Included
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	500	Sack Construction. 25% Discount for BIS.
4.4(Seam )	-	500	25% Discount for BIS.
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	500	25% Discount for BIS.
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	1050	Stitching Thread Material Identification. 25% Discount for BIS.
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	500	25% Discount for BIS.
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	Lengthwise. 25% Discount for BIS.
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	Width wise. 25% Discount for BIS.
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Avg. Breaking Strength & Elongation at Break -Top Seam. 25% Discount for BIS.
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Avg. Breaking Strength & Elongation at Break -Bottom Seam. 25% Discount for BIS.
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	25% Discount for BIS.
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200	25% Discount for BIS.
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	25% Discount for BIS.
5/5.6 (UV Resistance, )	-	12380	(Rs 10180 (Specimen Charge - 192 Hr UV Exposure) + 1100 (Lengthwise Breaking Strength) + 1100 (Width-wise Breaking Strength) Optional 25% Discount for BIS.
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	1100	Tenacity . 25% Discount for BIS.
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	1200	Ash Content . 25% Discount for BIS.
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	700	Density 25% Discount for BIS.
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	1050	Material Identification 25% Discount for BIS.
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	1100	MFR (Melt Flow Rate) 25% Discount for BIS.
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	700	Dimensional Stability 25% Discount for BIS.
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	700	Dimensional Stability 25% Discount for BIS.
4.3(Sacks)	-	0	-
4.4(Seam )	-	500	Stitching Construction 25% Discount for BIS.
4.4(Seam )	-	2000	Presence of UV stabilizer - Stitching Thread 25% Discount for BIS.
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	700	Linear Density of stitching Thread. 25% Discount for BIS.
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	500	Capacity
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	1050	Material Identification. 25% Discount for BIS.
4.5(Lamination )	-	500	Picks per dm. 25% Discount for BIS.
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Cl-5 Fig. 1- Table 1- Sr. no. ii(Ends per dm - Annex B 40 ± 2)	-	0	-
Cl-5 Fig. 1- Table 1-Sr. no. iii(Picks per dm-Annex B 40 ± 2)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm)	-	0	-
Cl-5, Fig. 1- Table 1-Sr. no. i(Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm)	-	0	-
Cl-5, Fig. 1, Table 1(i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm)	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-

07 Oct, 2028

-
Included w.e.f. 20.08.2024

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

49630 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.6(Drop Impact Test)	-	1600	25% Discount in Test Charges. (Rs. 1100 for Testing Charges & Rs. 500 for Specimen Charges)
4.1(Raw Meterial)	-	3250	25% Discount in Test Charges. (Raw Material Identification Rs 1050 & Overall Migration Rs1700 + Rs 500)
4.2("Fabric a) Width of Tape")	-	500	25% Discount in Test Charges.
4.2("Fabric b) Linear Density")	-	1000	(For Width & Thickness of Tape)
4.2("Fabric c) Mesh")	-	500	25% Discount in Test Charges. (Mesh Size)
4.2("Fabric c) Mesh")	-	1050	25% Discount in Test Charges. (For Identification of Fabric)
4.2("Fabric d) Unlaminated Fabric Mass")	-	500	25% Discount in Test Charges.
4.3(Sacks)	-	500	25% Discount in Test Charges.
4.4.1(Loose Liner)	-	1050	Liner Identification
4.4.1(Thickness of Linear)	-	500	25% Discount in Test Charges.
4.4.2(Visual Observation)	-	500	25% Discount in Test Charges.
4.4.3(Bottom Seam of Loose Liner)	-	500	25% Discount in Test Charges.
4.5(Mass of The Lamination)	-	1000	25% Discount in Test Charges. (Rs 500 for GSM & Rs 500 for Mass)
4.5(Laminated Fabric)	-	1550	25% Discount in Test Charges. (Rs 1050 for Identification & 500 for Lamination and Construction)
4.5(Lamination Over Hang of the fabric after trimming)	-	500	25% Discount in Test Charges.
4.6.1(Distance between the Two Row of Stitches)	-	1550	25% Discount in Test Charges. (Rs 1050 for Identification & Rs 500 for Distance bet. two rows of stitches.
4.6.1(Distance of outer stitch from the edge of the bag)	-	500	25% Discount in Test Charges.
4.6.1(Depth of the Stitch( Double fold))	-	500	25% Discount in Test Charges.
4.6.1(No.of Stitches/dm)	-	500	25% Discount in Test Charges.
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	1600	25% Discount in Test Charges. (Test Charge Rs 1100 + Rs 500 specimen Charges)
4.6.2(Breaking Load for UV Stabilized sack)	-	2000	25% Discount in Test Charges. (For Presence of UV stabilizer in stitching tread)
4.7(Mouth of the Sack)	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	0	25% Discount in Test Charges. Already Included
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	500	25% Discount in Test Charges.
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	2700	25% Discount in Test Charges. (Rs 2200 for Testing + Rs 500 for Specimen)
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	1600	25% Discount in Test Charges. (Rs 1100 for Testing + Rs 500 for Specimen)
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	1600	25% Discount in Test Charges. Width Wise Lamination Joint Breaking strength (Test Charge Rs 1100 + Rs 500 for Specimen)
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	25% Discount in Test Charges. (Already Included in Tensile Breaking Strength)
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	1200	25% Discount in Test Charges.
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	0	25% Discount in Test Charges. (Already Included)
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.2(Visual Observation)	-	500	25% Discount in Test Charges.
Cl. No.5.3(Mass of Bale)	-	0	25% Discount in Test Charges.
Cl. No.5.4(Breaking Strength of Fabric)	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.5("Ash Content a) For UV Stabilized Sack")	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.6(Drop Impact testing of filled sack)	-	0	25% Discount in Test Charges. (Already Included)
Cl. No.5.7(UV Resistance)	-	12880	25% Discount in Test Charges. (UV Exposure Charges Rs 10180 + Breaking Strength Before & After UV Rs 2200 + Rs 500 for specimen preparation)
Cl. No.6.1(Printing on Sacks)	-	0	25% Discount in Test Charges.
Cl. No.6.2.(Packaging)	-	0	25% Discount in Test Charges.
Cl. No.6.3.(Marking on the Bale)	-	0	25% Discount in Test Charges.
Cl. No.6.4.(BIS Certification Marking)	-	0	25% Discount in Test Charges.
Cl. No.6.5.(Storage)	-	0	25% Discount in Test Charges.

07 Oct, 2028

-
Included w.e.f. 20.08.2024

Bureau of Indian Standards

The National Standards Body of India

CIPET, Hajipur

INDUSTRIAL AREA, Hajipur, Vaishali, Bihar, 844102

7781020335 testing-hajipur@cipet.gov.in

Scope List