BIS - LIMS (Laboratory Information Management System)

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY

CITY CENTRE, P.O. DEBHOG, HALDIA, MEDINIPUR EAST, WEST BENGAL, INDIA, HALDIA, Medinipur East, West Bengal, 721657

9337476507 testing-haldia@cipet.gov.in

Scope List

Reset

18 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

All Types

18256 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.2(Film Form)	-	0	-
5.1.3(Odour)	-	0	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.5.1.6(a)(Carbon Black Content)	-	0	-
Cl.5.1.6(b)(Ash content)	-	0	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0	-
5.2.1.1(Nominal Thickness)	-	0	-
5.2.1.2(Nominal width)	-	0	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 5.2.3(Tolerance on Width)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800	Testing charge + Specimen ( 1300+500) Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Ageing changes (4200) Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	850	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1300	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 8.1(Table 3)(Break strength)	-	0	-
Clause 8.1(Table 3)(Break Elongation)	-	0	-
8.1, Table 3(Tear resistance , Annex B)	-	0	-
8.1, Table 3(Puncture resistance , Annex C)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2600	Testing charge + Specimen (MD/TD) (2600) Discount of 25% is applicable on Total Test Charges only for BIS
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tear resistance , Annex B)	-	0	-
9.1, Table 4(Puncture resistance , Annex C)	-	0	-

Complete

14 Dec, 2024

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

All

9156 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	1050	Discount of 25% is applicable on Total Test Charges only for BIS
4.2a(Carbon Black Content)	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.0 5.1 (Table1) (b)Tolerance on OD)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0	-
6.0 (6.1) (Visual appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
7.2(Reversion Test)	-	1200	(Testing Charges 700 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
7.3(Tensile Test)	-	1800	(Testing Charges 1300 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

Size upto 355 mm DN

12463 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1(High Density Polyethylene)	-	3425	(Density 700 + MFI 1100 + CBC 925 + CBD 700) Discount of 25% is applicable on Total Test Charges only for BIS
6(Dimensions of pipes)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
7(Visual Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
8.1(Hydraulic characteristics)	-	6400	Acceptance test + Type test (1600+4800) Discount of 25% is applicable on Total Test Charges only for BIS
8.2(Reversion)	-	1200	Testing charges+ Specimen charges (700+500) Discount of 25% is applicable on Total Test Charges only for BIS
8.3(Density)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
8.4(Melt Flow Rate)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

All

11488 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type of Fitting)	-	0	-
5(Colour of fittings)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.1,Table 1(Wall thickness)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.2 ,Table 2&3(Socket Dimensions)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.3(Dimensions of waste trap(Nahani Trap)	-	0	-
7.4(Chamfer)	-	0	-
8(Sealing Rings)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
10(Workmanship)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
11(Design requirements)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
11.1(Solvent cement type or Rubber ring type)	-	0	Discount of 25% is applicable on Total Test Charges only for BIS
11.2(Socket and spigot configeration)	-	0	NA
11.3(Access Openings)	-	0	-
11.4,Table 5(Vent cowl)	-	0	-
11.5,Table 6(Pipe Clips)	-	0	-
12.1(Visual appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
12.2(Stress relief test)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
12.3(Vicat softening tempewrature)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
12.4(Effect on water test)	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	Test charge+ Specimen charge ( 2000+500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.15, Annex B(Sulphated Ash Content)	-	1200	Discount of 25% is applicable on Total Test Charges only for BIS
16.1(Impact test)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
17(Watet tightness of joint)	-	850	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Capacity 7500 liter for Cylindrical vertical tank

17350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.1(Density)	-	1325	Testing charge+ Specimen charge ( 700+625) Discount of 25% is applicable on Total Test Charges only for BIS
4.2.2(MFR)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
4.2.3(Carbon Black Content )	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
4.2.3(Carbon Dispersion Test)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
5(Types and Features )	-	0	NA
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	3000	a)Minimum net capacity & gross capacity = 500 b) Over all diameter range = 500 c) Over all height range = 500 d) Minimum internal dia of Man-hole/Hand-hole = 500 e) Minimum wall & bottom thickness= 500 f) Visual Inspection for Flat area= 500
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	Discount of 25% is applicable on Total Test Charges only for BIS
5.4(Wall Thickness)	-	1000	(Thickness above effective height 500 + Thickness of outer layer 500) Discount of 25% is applicable on Total Test Charges only for BIS
6.1(Finish)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.1.1(Resistance to Deformation)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
7.1.2(Resistance to Deformation)	-	0	-
7.2(Resistance to Impact)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
7.3(Test for Top Load Resistance)	-	900	Discount of 25% is applicable on Total Test Charges only for BIS
7.4(Tensile Strength)	-	1800	Testing charge+ Specimen charge ( 1300+500) Discount of 25% is applicable on Total Test Charges only for BIS
7.5(Flexural Modulus)	-	1600	Testing charge+ Specimen charge ( 1100+500) Discount of 25% is applicable on Total Test Charges only for BIS
7.6(overall Migration)	-	2200	Testing charge+ Specimen charge ( 1700+500) Discount of 25% is applicable on Total Test Charges only for BIS
9.1(Lid Thickness)	-	500	i) Lid Thickness= 500 Discount of 25% is applicable on Total Test Charges only for BIS
9.1(Man-Hole and Hand-Hole Lids)	-	3175	i) Material Identification= 1050 ii) Carbon Black Content =925 iii) Carbon Black Dispersion = 700 iv) Visual Appearance= 500 Discount of 25% is applicable on Total Test Charges only for BIS
9.2(Man-Hole and Hand-Hole Lids)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
9.2.1(Man-Hole and Hand-Hole Lids)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.4(Wall Thickness above effective height)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

Nominal Diameter up to 355 mm & all classes

20013 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(CLASSIFICATION OF PIPES)	-	0	-
6(VCM CONTENT)	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
6(K- VALUE)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
10.3("Effect on Water a) Lead (first extraction) ")	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
10.3(b) Lead (Third extraction))	-	0	-
10.3(c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction))	-	0	-
10.3(d) Cadmium (All three extracts))	-	0	-
10.3(e) Mercury (All three extracts))	-	0	-
10.3(f) Other Toxic Substances)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1200	Testing charges: 700 + specimen:500 Discount of 25% is applicable on Total Test Charges only for BIS
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
Clause 10.7(Sulphated Ash Content)	-	1200	Discount of 25% is applicable on Total Test Charges only for BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	Discount of 25% is applicable on Total Test Charges only for BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	Discount of 25% is applicable on Total Test Charges only for BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	1500	Testing charges: 1000 + specimen:500 Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

All

13613 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	0	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	NA
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	NA
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	NA
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	NA
7.3.1(No.of Ribs)	-	0	NA
7.3.2(Rib height)	-	0	NA
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0	NA
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	NA
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	0	NA
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	0	NA
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	0	NA
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0	NA
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	0	NA
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	0	-
9.1(Visual Appearance)	-	0	-
9.2(Internal Diameter)	-	0	-
9.3(Density IS 12235 (Part 14))	-	0	-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	0	-
9.5(Tensile Strength IS 12235(Part 13))	-	0	-
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	0	-
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	0	-
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
4.1.2(K-Value as per IS-4669)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	0	-
4.1.2(K-Value as per IS-4669)	-	0	-
5(COLOUR)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	1500	(Test Charges 1000 + Specimen Charges 500) Discount of 25% is applicable on Total Test Charges only for BIS
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	0	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	0	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	1550	(Material Identification 1050 + Hardness 500) Discount of 25% is applicable on Total Test Charges only for BIS
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
9.1( Visual Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
9.2(Internal Diameter)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
9.3(Density IS 12235 (Part 14))	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	(Test Charges 1000 + Specimen Charges 500) Discount of 25% is applicable on Total Test Charges only for BIS
9.5(Tensile Strength IS 12235(Part 13))	-	1800	(Test Charges 1300 + Specimen Charges 500) Discount of 25% is applicable on Total Test Charges only for BIS
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000.03	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

Type A & B, All Size

17613 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	-
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	-
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	-
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	-
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1200	Testing charge + Specimen ( 700+500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	Testing charge+ Specimen (2000+500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1600	Testing charge+ Specimen (1100+500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	3600	Testing charge+ Specimen (1300 X 2+500X2) Tensile Strength (Before Exposure) & Tensile Strength (after Exposure) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	850	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
8.6(Effect on Water Test)	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

All Sizes

24468 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material )	-	1050	Discount of 25% is applicable on Total Test Charges only for BIS
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.3(Sacks)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.4(Seam )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	1550	(Material Identification 1050 + denier 500) Discount of 25% is applicable on Total Test Charges only for BIS
4.5(Lamination )	-	1050	Discount of 25% is applicable on Total Test Charges only for BIS
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.7(Valve for Filling of Sacks)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200	Discount of 25% is applicable on Total Test Charges only for BIS
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	12380	(UV Exposure (192 hrs.) 10180 + Breaking Strength length wise & widthwise 2200) Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

All Sizes

17269 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
(Cl.4.2)(Carbon black- a)carbon content)	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.5(Dimensions of pipe - i) Outside diameter)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.2(Ovality)	-	0	-
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	0	-
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	0	-
6(Visual appearance )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 7.1(Hydraulic Characteristics - Quality test)	-	4800	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 7.1(Hydraulic Characteristics - Acceptance test)	-	1600	Discount of 25% is applicable on Total Test Charges only for BIS
7.2(Reversion Test)	-	1200	(Test Charge 700 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.7.3(Tensile Test- i) Tensile Strength)	-	1800	(Test Charge 1300 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.7.3(Tensile Test - ii)Elongation at Break)	-	0	-
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	5300	(Test Charge 4800 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	Discount of 25% is applicable on Total Test Charges only for BIS
(Cl.7.5)(Density)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
7.6(Melt now Rate (MFR))	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
8(Supply of pipes)	-	0	-

Complete

14 Dec, 2024

IS 14182 (1994)

Solvent cement for use with unplasticized polyvinyl chloride plastic pipe and fittings - Specifications

All

8263 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Shall be thixotropic and consist substantially of solvents that will swell plastisized PVC polymers and stabilizers)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.3(Shall be capable of application by brush and shall contain no lumps or foreign matter or macroscopic undissolved particles that will adversely affect the ultimate joint strength or chemical resistance of the material )	-	0	NA
4.4(Shall not show gelation and no evidence of stratification or separation that cannot be removed by stirring)	-	0	NA
4.5(When used under the conditions for which they are designed, non metallic materials in contact with or likely to come in contact with potable water shall not constitute a toxic hazard , shall not support microbial growth and shall not give rise to unpleasant taste or odour, cloudiness or discolouration of the water)	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
4.7(Vinyl Chloride Polymer content - Annex A)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
4.8(Dissolution - Capable of dissolving an additional unplastisized PVC granular, powder compound or resin)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.9 and 6.1(Viscosity - Regular)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
4.9 and 6.1(Viscosity - Medium)	-	0	NA
4.9 and 6.1(Viscosity - Heavy )	-	0	NA
4.10 and 6.1(Lap Shear Strength - After 2 h curing time)	-	1600	Test Charges =1100 & 500 specimen charges Discount of 25% is applicable on Total Test Charges only for BIS
4.10 and 6.1(Lap Shear Strength - After 10 h curing time)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
4.10 and 6.1(Lap Shear Strength - After 72 h curing time)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
4.11 and 6.1(Hydrostatic Burst Strength - After 2 h curing time)	-	850	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

All size

7388 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	-
6.1(Stress Relief Test)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
6.2(Opacity)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
6.3(Effect on Water)	-	3000	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	850	Discount of 25% is applicable on Total Test Charges only for BIS
6.1.1(VCM Content Test)	-	4100	(VCM 3000 + K-Value 1100) Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

All sizes

107369 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 7(Dimensions Of Pipes)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 8(Visual Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.1(Hydraulic Characteristics)	-	18400	i) Acceptance test (1 h. / 20 oC ) = 1000 ii) Acceptance test (22 h. / 95 oC ) = 1600 iii) Type test (165 h. / 95 oC ) = 4800 iv) iii) Type test (1000 h. / 95 oC ) = 11000 Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.2(Fusion Compatibility)	-	4800	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.3(Reversion Test )	-	1200	700 test charges + 500 specimen charges Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.4 & Annex B(Impact Strength)	-	1600	1100 test charges + 500 specimen charges Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.5(Density)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.6(Melt Flow Rate)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	925 CBC + 700 CBD Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	(Test Charges 1700 + 82125) Discount of 25% is applicable on Total Test Charges only for BIS
Cl 9.9(Opacity)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

All

7463 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	1050	Discount of 25% is applicable on Total Test Charges only for BIS
4.2(Design, Shape and Dimensions)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.3(Workmanship and Finish)	-	0	-
Cl. 4.4 (a)(Capacity)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
4.4 (b)(Brimful Capacity)	-	0	-
Cl. 4.5(Cl. 4.5 Wall Thickness (Top))	-	499.99	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 4.5(Cl. 4.5 Wall Thickness (Middle))	-	0	-
Cl. 4.5(Cl. 4.5 Wall Thickness (Bottom))	-	0	-
4.6.2(Transparency)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
4.6.3, clause 6 of IS:2798:1998(Leakage test- a. Closure leakage )	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
4.6.3, clause 6 of IS:2798:1998(Leakage test- b. Vibration leakage)	-	0	-
4.6.3, clause 6 of IS:2798:1998(Leakage test- c. Air pressure leakage)	-	0	-
4.6.4, clause 8 of IS:2798:1998(Drop test )	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
Cl. 4.6.5(Overall migration for container)	-	1700	Discount of 25% is applicable on Total Test Charges only for BIS
4.6.5.1 (chem)(Colour migration (Container))	-	0	-
4.6.5.1 (chem)(Colour migration (Caps))	-	0	-
4.6.6(Water potability Test)	-	2900	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

All Sizes

32756 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.0((a) Carbon black content)	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
3.0((b) Carbon black dispersion)	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
3.0((a) Outside diameter)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
3.0((i) Tolerance)	-	0	-
3.0((ii) Ovality)	-	0	-
3.0(Minimum)	-	0	-
3.0(maximum)	-	0	-
3.0(Visual Appearance)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Out of Squareness)	-	0	-
3.0((i)Quality Test at 3.5MPa induced stress for 165 hours at 80°C)	-	4800	Discount of 25% is applicable on Total Test Charges only for BIS
3.0((ii)Acceptance Test at 3.8MPa induced stress for 48 hours at 80°C)	-	1600	Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Reversion test)	-	1200	(Test Charge 700 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Tensile strength at yield)	-	1800	(Test Charge 1300 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Elongation at break)	-	0	-
3.0(Fusion Compatibility Test (i)Quality Test at 3.5MPa induced stress for 165 hours at 80°C)	-	1600	Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Fusion Compatibility Test (ii)Acceptance Test at 3.8MPa induced stress for 48 hours at 80°C)	-	5300	(Test Charge 4800 + Specimen Charge 500) Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Density at 27°C (Base material))	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Melt flow rate at 190°C/5 kg)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
3.0(Supply of Pipe)	-	0	-
4.1 .1.2.1(HDPE couplers)	-	6700	Discount of 25% is applicable on Total Test Charges only for BIS
Cl.4.1.3(Workmanship and appearance )	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 4.1.4(Holding attachments for coupler parts)	-	0	-
Cl 4.1.5(Rubber rings- A)Shore hardness (Shore-A))	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
Cl 4.1.5(Rubber rings- B) Change in hardness)	-	4800	500 Hardness test + 4300 Ageing Discount of 25% is applicable on Total Test Charges only for BIS
Cl 4.1.5(Rubber rings- C)Rubber ring shall be of black colour:)	-	1550	(Identification 1050 + Colour 500) Discount of 25% is applicable on Total Test Charges only for BIS
6.1.1, 6.1.1.1(Leakage Test)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
6.1.2, 6.1.2.1( Hydraulic Proof Test)	-	1000	Discount of 25% is applicable on Total Test Charges only for BIS
6.1.3, 6.1.3.1(Weldability Test)	-	6400	(Quality 4800 + Acceptance 1600) Discount of 25% is applicable on Total Test Charges only for BIS
6.1.3.2 (Quick coupled fittings)	-	0	-

Complete

14 Dec, 2024

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

All Sizes

7363 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	NA
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	NA
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0	NA
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	700	Discount of 25% is applicable on Total Test Charges only for BIS
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1350	(Test Charges 850 + Specimen Charges 500) Discount of 25% is applicable on Total Test Charges only for BIS
6.3(Effect on water test)	-	3000	-
3(Material)	-	4100	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

All Sizes

7363 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	9650	Test Charges 9150 + Specimen Charges 500 Discount of 25% is applicable on Total Test Charges only for BIS
3.2.1, Table-1, Fig-1(Nominal size)	-	0	-
3.2.1, Table-1, Fig-1(B)	-	0	-
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	0	-
Clause 3.2.2, and Fig. 2(Nominal size)	-	0	-
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	0	NA
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	0	Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Upto 355 DN

31869 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1 table-1(MATERIALS)	-	0	NA
5.2(Polyethylene Resin)	-	4525	Complete testing charges for Raw material Discount of 25% is applicable on Total Test Charges only for BIS
5.3 (a)(Carbon Black Master Batch)	-	1875	For CBC+ Ash content (925+950) Discount of 25% is applicable on Total Test Charges only for BIS
5.3(b)(Carbon Black Master Batch)	-	1875	For CBC+ Ash content (925+950) Discount of 25% is applicable on Total Test Charges only for BIS
5.3(c)(Carbon Black Master Batch)	-	1875	For CBC+ Ash content (925+950) Discount of 25% is applicable on Total Test Charges only for BIS
5.3(d)(Carbon Black Master Batch)	-	1875	For CBC+ Ash content (925+950) Discount of 25% is applicable on Total Test Charges only for BIS
5.3(e)(Carbon Black Master Batch)	-	1875	For CBC+ Ash content (925+950) Discount of 25% is applicable on Total Test Charges only for BIS
5.4(Anti oxydent)	-	0	NA
8.3(Carbon black)	-	925	Discount of 25% is applicable on Total Test Charges only for BIS
8.6(Overall migration)	-	2000	Testing charge:1700+ Specimen: 300 Discount of 25% is applicable on Total Test Charges only for BIS
6, 6.1(PIPE DESCRIPTION)	-	0	NA
6, 6.1.1(PIPE DESCRIPTION)	-	0	NA
6, 6.1.2(PIPE DESCRIPTION)	-	0	NA
6.1.3 (PIPE DESCRIPTION)	-	0	NA
6.1.4(PIPE DESCRIPTION)	-	0	NA
6.2(Colour)	-	250	Discount of 25% is applicable on Total Test Charges only for BIS
6.2.1(6.1.1 Identification Stripes)	-	250	Discount of 25% is applicable on Total Test Charges only for BIS
7.2(Length)	-	250	Discount of 25% is applicable on Total Test Charges only for BIS
7.4 table -3 & 4(6.1 Dimensions)	-	250	Discount of 25% is applicable on Total Test Charges only for BIS
7.4.1.2(Ovality)	-	250	Discount of 25% is applicable on Total Test Charges only for BIS
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	(a) Acceptance Test (48 hrs.)/80˚ C: 1600 + (b) Type Test (100 hrs.)/27˚ C:4000+ (c) Type test (165 hrs.)/80˚ C:4800 + (d) Type test (1000 hrs.)/80˚ C:11000. Discount of 25% is applicable on Total Test Charges only for BIS
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	Discount of 25% is applicable on Total Test Charges only for BIS
8.2(Longitudinal Reversion Test)	-	900	Testing charge+ Specimen (700+200) Discount of 25% is applicable on Total Test Charges only for BIS
8.4( Melt Flow Rate)	-	1100	Discount of 25% is applicable on Total Test Charges only for BIS
8.5 (Oxidation Induction Time)	-	2200	Discount of 25% is applicable on Total Test Charges only for BIS
8.7(Density)	-	500	Discount of 25% is applicable on Total Test Charges only for BIS
8.8(Tensile Strength for Butt-fusion)	-	1600	Testing charges + Specimen ( 1100+500) Discount of 25% is applicable on Total Test Charges only for BIS
8.9 table-6(Elongation at Break)	-	1600	Testing charges + Specimen ( 1100+500) Discount of 25% is applicable on Total Test Charges only for BIS
8.10(Slow Crack Growth Rate)	-	6000	Testing charges + Specimen ( 5500+500) Discount of 25% is applicable on Total Test Charges only for BIS

Complete

14 Dec, 2024

Bureau of Indian Standards

The National Standards Body of India

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY

CITY CENTRE, P.O. DEBHOG, HALDIA, MEDINIPUR EAST, WEST BENGAL, INDIA, HALDIA, Medinipur East, West Bengal, 721657

9337476507 testing-haldia@cipet.gov.in

Scope List