BIS - LIMS (Laboratory Information Management System)

INDIAN RUBBER MATERIALS RESEARCH INSTITUTE (IRMRI)

Plot No. 254/1B, Road no. 16V, Wagle Industrial Estate, Thane, Thane, Maharashtra, 400604

2267873200 rk@irmra.org

Scope List

Reset

25 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5382 (2025)

RUBBER SEALS JOINT RINGS FOR WATER SUPPLY DRAINAGE AND SEWERAGE PIPELINES SPECIFICATION FOR MATERIALS ( Third Revision )

330520 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(General requirement)	-	300	-
Cl-5.4(Dimensional tolerances)	-	600	-
Cl-5.5(Imperfections and defects)	-	300	-
Cl-5.6(Hardness)	-	1200	-
Cl-5.7(Tensile strength and elongation at break)	-	2000	-
Cl-5.8.1(Compression set in air-General)	-	3400	-
Cl-5.8.2(Compression set in air-Compression set at 23 °C and 70 °C.)	-	5600	-
Cl-5.8.3(Compression set in air-Low-temperature compression set at 72–10 °C)	-	14840	-
Cl-5.9(Accelerated ageing in air-7 days at 70 °C.)	-	5600	-
Cl-5.9(Hardness change, max./min.)	-	1200	-
Cl-5.9(Tensile-strength change, max)	-	1200	-
Cl-5.9(Elongation change, max./min)	-	800	-
Cl-5.10(Stress relaxation in compression-7 days at 23 °C)	-	14700	-
Cl-5.10(Stress relaxation in compression-100 days at 23 °C)	-	210000	-
Cl-5.11(Volume change in water max./ min. 7 days at 70 °C)	-	1700	-
Cl-5.12(Ozone resistance)	-	10080	-
Cl-5.13.1(Spliced joints)	-	1800	-
Cl-5.13.2(Strength of spliced joints)	-	0	-
Cl-6.1(Low temperature performance at –25 °C, (type L))	-	3900	-
Cl-6.1(Compression set, max. 72 h at −25 °C)	-	14840	-
Cl-6.1(Hardness change, max 168 h at −25 °C)	-	29760	-
Cl-6.2(Volume change in oil, max./min. 72 h at 70 °C (type O))	-	6100	-
Cl-11(Marking and labelling)	-	600	-

-
Included w.e.f. 26.02.2026 Exclusion: "Cl-5.2 (Effect on water quality) Cl-5.3 (Microbiological deterioration) Cl-6.3 (Lifetime estimation, (type LT).) Cl-6.4 (Summary of optional property requirements) "

IS 12585 (2023)

SPECIFICATION FOR THERMOPLASTIC HOSES (TEXTILE REINFORCED) FOR WATER - GENERAL PURPOSE ( First Revision of IS 12585 )

Type1 (Low pressure)/ Type 2 (Medium)/ Type 3 (High Pressure)

50800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials and Construction)	-	300	-
5(Materials and Construction)	-	300	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	300	-
6.2(Concentricity)	-	300	-
6.3(Tolerance on Length)	-	300	-
6.4(Minimum Wall Thickness)	-	300	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	1000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	2100	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	1000	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	4400	-
5(Materials and Construction)	-	300	-
5(Materials and Construction)	-	300	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	300	-
6.2(Concentricity)	-	300	-
6.3(Tolerance on Length)	-	300	-
6.4(Minimum Wall Thickness)	-	200	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	1000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	900	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	2400	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	1000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	2100	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	1000	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	4400	-

-
Included w.e.f. 24.02.2026

IS 10908 (2023)

FLEXIBLE RUBBER TUBING FOR LIQUEFIED PETROLEUM GAS SPECIFICATION Second Revision

16300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The materials used in the manufacture of tubing shall be homogeneous and shall be resistant to outdoor exposure.)	-	100	-
4.1(The tubing made out of this material shall be green in colour and shall be supplied normally in cut lengths or in rolls of running length)	-	100	-
4.1("when supplied in cut lengths, the pieces shall be of minimum 1.0 m to maximum of 1.5 m in length. ")	-	100	-
4.2(The walls shall be seamless and free from all visible defects, such as lumps, blow-holes, cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas.)	-	100	-
4.3.1(The tubing when supplied in 6.4 mm inside diameter; the tolerance as per table-1)	-	200	-
4.3.1(The tubing when supplied in 7.00 mm inside diameter; the tolerance as per table-1)	-	200	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.20 mm))	-	200	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.50 mm))	-	200	-
4.4.1(When tested in accordance with the method given in Annex B, the tubing shall fit over the standard and oversize metal nozzle shown in Fig. 1, 2 and 3.)	-	1300	-
4.4.2("When tested in accordance with the method given in Annex B, the tubing shall remain attached to both nozzles throughout the test period. ")	-	1300	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), the increase in the outside diameter or the tubing shall not be more than 15 percent.)	-	1000	-
4.12("When tested in accordance with the method described in Annex F, the tubing shall not burn to either of the outer marks within the test period of 45 s")	-	1000	-
4.11("When tested in accordance with the method described in Annex E, the slit tube shall not show any breakage on surface or cracks or defects.")	-	3000	-
4.10(When tested in accordance with Annex D, the npentane absorbed shall not exceed 15 percent of the initial mass of the tubing and the amount of npentane extractable matter shall not exceed 10 percent of the initial mass of tubing.)	-	2000	-
4.9(60 cm long tubing shall be subjected to a crushing force of 350 N applied on the middle of the tubing evenly over a length of 25 mm for 5 minutes, and 30 min after removal of the force it shall not show any deformation or collapse, nor shall it leak when subjected to an internal air pressure of 250 kPa)	-	1000	-
4.8.2(The tubing shall be so flexible that it will make contact with a cylindrical former of radius 68 mm for at least 110° of its circumference when the immersed tubing is placed over the former and a mass of 1.6 kg is attached to each end.)	-	1000	-
4.8.1("The tubing shall be immersed for 72 h in liquid pentane and then conditioned at room temperature for 24 h, after which it shall be tested in accordance with the method prescribed in Annex C, the gas pressure shown on the manometer shall not drop by more than 1 kPa")	-	1000	-
4.7("The flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100 °C for 72 h in accordance with the normal method prescribed in IS 3400 (Part 4). It shall not show a change of + 10° A of its original shore hardness value (see 4.6) after accelerated ageing")	-	1000	-
4.6(The hardness on the flat surface of the cut/slit tubing shall be measured as prescribed in IS 3400 (Part 2/Sec 4), the shore hardness shall be 60 ± 5°A.)	-	500	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), there shall be no sign of leakage in the tubing. Also the same shall not burst when the pressure is increased to 0.5 MPa or 500 kPa (5 bar), The test shall be carried out on a length of 60 cm.)	-	1000	-

-
included w.e.f 17.02.2026

IS 13098 (2024)

AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES â SPECIFICATION (second revision)

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Materials)	-	600	-
Cl 3.2(Classification)	-	3800	-
Cl 3.2.1(Blend Name)	-	3800	-
Cl 3.3(Fit)	-	600	-
Cl 3.3.1(Thickness Uniformity)	-	600	-
Cl 4.1.1(Elongation)	-	1900	-
Cl 4.1.2(Strength of Splice)	-	1900	-
Cl 4.1.3(Set After Ageing)	-	3600	-
Cl 4.1.4(Accelerated Ageing)	-	3500	-
Cl 5(AIR TIGHTNESS)	-	600	-
Cl 6(MARKING)	-	600	-

-
included w.e.f 09.02.2026

IS 14261 (1995)

Transmission devices - V - Belts endless narrowv - Belts for industrial use - Specification

SPZ, SPA, SPB, SPC

8700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Material And Workmanship)	-	600	-
Cl 5.1(Cross-Section Dimensions)	-	1500	-
Cl 5.2(Cross-Section Dimensions)	-	1500	-
Cl 6(DESIGNATION)	-	600	-
Cl 7(Length Measurement And Tolerances)	-	0	Included in Determination of Pitch Length
Cl 7.2.1(Determination of Pitch Length)	-	3000	-
Cl 7.3(Matched Belts)	-	1500	-

-
Included w.e.f. 26.09.2025

IS 2494 : Part 1 (1994)

V - Belts - Endless V - Belts for industrial purposes: Part 1 general purpose - Specification (Second Revision)

Z, A, B, C, D, E, SPZ. SPA. SPB, SPC

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.0(Marking)	-	600	-
10.1(Elongation)	-	2500	-
10.1(Tensile Strength)	-	0	Included in the Elongation Charges
7.2.2(Matched Belts - Code)	-	2000	-
7.2.1(Matched Belts - Difference)	-	1500	-
7.1(Belt Pitch Length)	-	3000	-
6.0(Designation)	-	600	-
4.1(Material and Workmanship)	-	600	-
4.1(Material -Reinforcing polyester cord/fabric of the V-belts)	-	0	Included in the 4.1
4.1(Material and Workmanship)	-	0	Included in the 4.1
7.2(Test Matched Belts)	-	0	Included in the Matched belt difference.
5 & 11(Test Belt ride position of top surface of belt with respect to top of pully groove.)	-	1500	-
Clause 5 Table 1(Nominal Pitch Width (Wp))	-	1500	-
Clause 5 Table 1(Nominal Height (T))	-	1500	-
Clause 5 Table 1(Nominal Included Angle (A))	-	2500	-
Clause 5 Table 1(Nominal Pitch Width (W))	-	1500	-
Cl-4.3(Presence of polychloroprene rubber on outside jacket of V-belt)	-	3800	-
4.1(Material -Reinforcing polyester cord/fabric of the V-belts)	-	0	duplicate
7.2(Test Matched Belts)	-	0	duplicate
5 & 11(Test Belt ride position of top surface of belt with respect to top of pully groove.)	-	0	duplicate
Clause 5 Table 1(Nominal Pitch Width (Wp))	-	0	duplicate
Clause 5 Table 1(Nominal Height (T))	-	0	duplicate
Clause 5 Table 1(Nominal Included Angle (A))	-	0	duplicate
Clause 5 Table 1(Nominal Pitch Width (W))	-	0	duplicate
Cl-4.3(Presence of polychloroprene rubber on outside jacket of V-belt)	-	0	duplicate

-
Included w.e.f 12.11.2025 Exclusion: 8.0 (Transmitting Capacities) , 5 Table 2B (Cross sectional dimension), 5 Table 2A (Cross sectional dimension), 5 Table 1 (Cross sectional dimension)

IS 7466 (2023)

Rubber Gasket for Pressure Cooker ï¿½ Specification ( Second Revision )

78500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 4.2(Workmanship and Finish)	-	600	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	1200	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	1000	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	900	-
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	5500	-
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	6700	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	1700	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	3600	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	1500	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	1000	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	800	-
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	4700	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	12400	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	15000	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	1900	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	1900	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	1900	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	1900	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	1900	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	1900	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	1900	-
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	1900	-
Cl. No. 5(Packing and Marking)	-	0	-
Cl. No.4.6(Performance test)	-	4800	-
Cl. No. 3(Types)	-	3800	-
Cl. No. 4.3(Dimensions)	-	1500	-
Cl. No. 4.2(Workmanship and Finish)	-	600	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	1200	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	1000	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	900	-
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	5500	-
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	6700	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	1700	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	3600	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	1500	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	1000	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	800	-
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	4700	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	12400	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	1900	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	1900	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	1900	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	1900	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	1900	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	1900	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	1900	-
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	1900	-
Cl. No.4.6(Performance test)	-	4800	-
Cl. No. 3(Types)	-	3800	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	15000	The charge for this test is already included. It's repeated
Cl. No. 4.2(Workmanship and Finish)	-	600	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(i)(Hardness)	-	1200	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	1000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	900	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	5500	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	6700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	1700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	3600	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	1500	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	1000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	800	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	4700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	12400	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	1900	The charge for this test is already included. It's repeated
Cl. No.4.6(Performance test)	-	4800	The charge for this test is already included. It's repeated
Cl. No. 3(Types)	-	3800	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	15000	The charge for this test is already included. It's repeated
Cl. No. 4.2(Workmanship and Finish)	-	600	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(i)(Hardness)	-	1199.99	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	1000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	900	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	5500	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	6700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	1700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	3600	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	1500	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	1000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	800	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	4700	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	12400	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	1900	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	1900	The charge for this test is already included. It's repeated
Cl. No.4.6(Performance test)	-	4800	The charge for this test is already included. It's repeated
Cl. No. 3(Types)	-	3800	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	15000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	10000	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xiii)(N-Nitrosatables)	-	10000	The charge for this test is already included. It's repeated
Cl. No. 4.2(Workmanship and Finish)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(i)(Hardness)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	0	The charge for this test is already included. It's repeated
Cl. No.4.6(Performance test)	-	0	The charge for this test is already included. It's repeated
Cl. No. 3(Types)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xiv)(Extractables)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.2(Workmanship and Finish)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(i)(Hardness)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	0	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	0	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	0	The charge for this test is already included. It's repeated
Cl. No.4.6(Performance test)	-	0	The charge for this test is already included. It's repeated
Cl. No. 3(Types)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	0	The charge for this test is already included. It's repeated
Cl. No. 4.4, table no. 1(xiv)(Extractables)	-	12400	-
Cl. No. 4.3(Dimensions)	-	1800	The charge for this test is already included. It's repeated
Cl. No. 4.2(Workmanship and Finish)	-	0	-
Cl. No. 4.4, table no. 1(i)(Hardness)	-	0	-
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	0	-
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	0	-
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	0	-
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	0	-
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	0	-
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	0	-
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	0	-
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	0	-
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	0	-
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	0	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	0	-
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	0	-
Cl. No. 4.5, Table no. 2(ii)(Arsenic)	-	0	-
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	0	-
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	0	-
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	0	-
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	0	-
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	0	-
Cl. No.4.6(Performance test)	-	0	-
Cl. No. 3(Types)	-	0	-
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	0	-
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	0	-
Cl. No. 4.4, table no. 1(xiv)(Extractables)	-	0	-
Cl. No. 4.3(Dimensions)	-	0	-

-
Included w.e.f.23.06.2025 Exclusion Excluding table(2)

IS 2494 : Part 2 (1993)

V - Belts - Endless V - Belts for industrial purposes: Part 2 fire resistant and antistatic V - Belts - Specification

17300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Fire Resistance Test)	-	2200	-
7.2(Electrical Resistance Test)	-	4000	-
7.3(Tensile Test)	-	3400	-
7.1(Fire Resistance Test)	-	2200	-
7.2(Electrical Resistance Test)	-	4000	-
7.3(Tensile Test)	-	3400	-
5(Requirements)	-	7700	-

-
included w.e.f.03.06.2025

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

Toy

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	500	--
4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	500	--
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	500	--
4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test)	-	500	--
4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	500	--
4.3.2 - 5.21( Expanding materials)	-	500	--
4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	500	--
4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	500	--
4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-	500	--
4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters)	-	500	--
4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys)	-	500	--
4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	500	--
4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	500	--
4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test)	-	500	--
4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	500	--
4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization)	-	500	--
4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	500	--
4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	500	--
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	500	--
4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-	500	--
4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	500	--
4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-	500	--
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test)	-	500	--
4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	500	--
4.18.2(b)(Projectile toys-Projectiles)	-	500	--
4.18.2(c)(Projectile toys-Projectiles)	-	500	--
4.18.2(c)(Projectile toys-Projectiles-Radius)	-	500	--
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	500	--
4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test)	-	500	--
4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup)	-	500	--
4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test)	-	500	--
4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup)	-	500	--
4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test)	-	500	--
4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing)	-	500	--
4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	500	--
4.18.3(b)(Projectile toys-Projectile toys with stored energy)	-	500	--
4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-	500	--
4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	500	--
4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components)	-	500	--
4.18.3(c )(Projectile toys-Projectile toys with stored energy)	-	500	--
4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	500	--
4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism)	-	500	--
4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	500	--
4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	500	--
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	500	--
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test)	-	500	--
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After torque test)	-	500	--
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective components)	-	500	--
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After tension test for protective components)	-	500	--
4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-	500	--
4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	500	--
4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	--
4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	--
4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	--
4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test)	-	500	--
4.18.4.6 - 5.24.5 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set- kinetic energy per area After torque test)	-	500	--
4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective components)	-	500	--
4.18.4.6 - 5.24.6.4 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-kinetic energy per area After tension test for protective components)	-	500	--
4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	500	--
4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases)	-	500	--
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals))	-	500	--
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	500	--
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	500	--
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals))	-	500	--
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	500	--
4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	500	--
4.21(a)(Braking-brake performance for mechanically or electrically powered ride-on toys other than toy bicycles)	-	500	--
4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	500	--
4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	500	--
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	500	--
4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	500	--
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	500	--
4.6.1 b(Edges-Accessible sharp edges of glass or metal- gap between the edge and the adjacent surface)	-	500	--
4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials)	-	500	--
4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments)	-	500	---
4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-	500	--
4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	500	---
4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms)	-	500	---
4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys)	-	500	--
4.7.3 (Wooden toys)	-	500	--

-
-

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

Toy

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	5000		--
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	5000		---

-
Included w.e.f. 3-6-2021.

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	1500	--

-
Included w.e.f. 3-6-2021.

IS 12118 : Part 1 (1987)

Specification for two - Part polysulphide - Based sealants: Part 1 general requirements

Pouring Grade

71000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1.1(Pouring Grade Sealants)	-	11300	--
5.1.2(Plastic Deformation)	-	11300	--
5.1.3(Adhesion and Tensile Modulus)	-	11300	--
5.1.4(Application Life)	-	11300	--
5.1.5(Adhesion in Peel)	-	11300	----
5.1.6(Loss of Mass after Heat Ageing)	-	11300	-----
5.1.7(Staining )	-	11300	-----
5.1.1.2(Gun Grade Sealant )	-	4000	-----

-
Included w.e.f. 3-6-2021.

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

Flammability (Safety of Toys)

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	3000	---
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	3000	--
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	3000	--
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	3000	--

-
Included w.e.f. 3-6-2021

IS 446 (2017)

Rubber hoses, textile - Reinforced, for compressed air - Specification (Fifth Revision)

RUBBER AIR HOSE

34170 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material and Construction)	-	900	--
6, Dimensions(Internal Diameter)	-	300	--
6, Dimensions(Concentricity)	-	500	--
6, Dimensions(Tolerance on Length)	-	300	---
6, Dimensions(Thickness of Lining of Type 1)	-	300	---
6, Dimensions(Thickness of Lining of Type 2)	-	300	--
6, Dimensions(Thickness of Lining of Type 3)	-	300	--
6, Dimensions(Thickness of Cover of Type 1)	-	300	--
6, Dimensions(Thickness of Cover of Type 2)	-	300	---
6, Dimensions(Thickness of Cover of Type 3)	-	300	--
7.1, Table 2(Tensile Strength of Lining)	-	950	--
7.1, Table 2(Tensile Strength of Cover)	-	950	--
7.1, Table 2(Elongation at Break of Lining of all types)	-	0	--
7.1, Table 2(Elongation at Break of Cover of all types)	-	0	--
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Lining of its original value)	-	1550	--
7.1, Table 2(Accelerated Ageing for all types: Change in Tensile Strength of Cover of its original value)	-	1550	--
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Lining of its original value)	-	0	--
7.1, Table 2(Accelerated Ageing for all types: Change in Elongation of Cover of its original value)	-	0	---
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class B only)-Lining)	-	850	---
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class C only)-Lining)	-	850	--
7.1, Table 2(Resistance to Liquid , Increase in Volume (Class C only)-Cover)	-	850	--
7.2, Table 3(Adhesion between Components- Lining and Reinforcement)	-	1050	--
7.2, Table 3(Adhesion between Components- Reinforcement layers)	-	1050	--
7.2, Table 3(Adhesion between Components- Cover and Reinforcement)	-	1050	--
7.2, Table 3(Proof Pressure at 23°C for type 1)	-	1950	--
7.2, Table 3(Proof Pressure at 23°C for type 2)	-	1950	--
7.2, Table 3(Proof Pressure at 23°C for type 3)	-	1950	--
7.2, Table 3(Change in Length at Maximum working Pressure)	-	1950	---
7.2, Table 3(Change in Diameeter at Maximum working Pressure)	-	0	---
7.2, Table 3(Minimum Bursting Pressure for type 1)	-	1950	--
7.2, Table 3(Minimum Bursting Pressure for type 2)	-	1950	--
7.2, Table 3(Minimum Bursting Pressure for type 3)	-	1950	--
7.2, Table 3(Ozone Resistance)	-	2520	--
7.2, Table 3(Low temperature Flexibility)	-	1950	--
7.2, Table 3(Flexibility at 23°C)	-	1550	--

-
REVISED VERSION OF IS 447:2017 INCLUDED W.E.F. 3-6-2021.

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

Rubber Hose for LPG-Specific Part 2 Domestic/Commercial

18600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	300	--
Clause 4.2.2 (a)(Reinforcement)	-	300	--
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	300	---
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	300	--
Clause 4.3 Sub Clause 4.3.3(Length)	-	300	--
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	950	--
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	950	--
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	0	--
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	0	----
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1550	--
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	0	--
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1550	--
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	0	--
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1800	--
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1050	--
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1950	--
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1050	--
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	750	---
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1950	---
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1950	--
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1050	--
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	300	--
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	0	--
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	0	--
Clause 5.2 (d)(Marking Batch/Lot No. )	-	0	--
Clause 5.2 (e)(Marking Month and year of manufacture )	-	0	--
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	0	--
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	0	--
Clause 5.2.1(BIS Certification Marking )	-	0	--
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	250	--

-
-

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

Rubber Hose for LPG-Specification Part 1 Industrial App

21420 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	300	---
Clause 4.2.2(Reinforcement)	-	300	---
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	300	---
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	300	--
Clause 4.3 Sub Clause 4.3.3(Length)	-	300	---
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	950	---
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	950	---
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	0	--
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	0	--
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1550	--
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	0	--
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1550	--
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	0	--
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1050	--
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1950	---
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1050	--
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1800	--
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	1300	--
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2520	---
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1950	--
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1950	--
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1050	--
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	300	--
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	0	---
Clause 5.2 (c)(Marking Nominal bore )	-	0	--
Clause 5.2 (d)(Marking Batch/Lot No. )	-	0	--
Clause 5.2 (e)(Marking Month and year of manufacture )	-	0	--
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	0	--
Clause 5.2.1(BIS Certification Marking )	-	0	--

-
-

IS 5382 (2018)

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (Second Revision)

Rubber Seals-Joint Rings for Water Supply, Drainage

81320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.1(Dimensional tolerances)	-	600	--
4.2.2(Imperfections and defects)	-	0	--
4.2.3(Hardness, IRHD from buttons )	-	1200	---
4.2.4(Tensile strength, MPa)	-	1900	--
4.2.2(i)In zones involved in sealing function)	-	0	--
4.2.2(ii) In zones not involved in sealing function)	-	0	---
4.2.5(Compression set in air)	-	0	--
4.2.5.2(Compression set at 23 ºC for 72 h)	-	5600	--
4.2.5.2(Compression set at 70 ºC for 24 h)	-	3400	--
4.2.5.3(Low temp compression set at -10 ºC for 72 h)	-	14840	--
4.2.6(Ageing 7 days at 70 ºC)	-	5600	--
4.2.6(Hardness, IRHD from buttons Tensile strength, % Elongation at break , % )	-	3100	--
4.2.7(Stress relaxation, max)	-	14700	for 7 days
4.2.8(Volume change in water , max/min 7 days at 70 ºC )	-	7300	--
4.2.9(Ozone resistance)	-	10080	--
4.2.10(Spliced joint)	-	1800	--
4.2.10.2(Strength of Spliced Joints)	-	0	---
4.3.1(Low temperature performance - 25 degree C)	-	3900	---
4.3.2(Volume change in oil)	-	7300	---

-
REVISED VERSION OF IS 5382:2018 INCLUDED W.E.F. 3-6-2021.

IS 3565 (2018)

Teats for feeding bottles - Specification (First Revision)

TEATS FOR FEEDING BOTTLES

33000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 5.3.1 Table 1 (iii) (Ash content)	-	950	--
Clause 5.3.1 Table 1 (ii) (b) (Free sulphur)	-	2500	---
Clause 5.2 ( sub clause 5.2.1)(Workmanship and Finish )	-	300	--
Clause 5.2 ( sub clause 5.2.2)(Shape & Size )	-	0	--
Clause 5.2 ( sub clause 5.2.3) Annex A.(Resistance to Autoclaving )	-	1800	--
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ i Annex B(Water Extract a) pH)	-	500	---
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ i Annex B(b) Colour)	-	300	----
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ i Annex B(c) Turbidity )	-	0	---
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ i Annex B(d) Odour)	-	0	---
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ ii Annex C(Acetone extract, percent: a) Acetone extracted material, percent by mass, Max)	-	1750	----
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ iv Annex E(Volatile components, percent Max)	-	500	----
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(Migration of Heavy Metals i) Antimony)	-	1400	---
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(ii) Arsenic)	-	750	---
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(iii) Chromium)	-	750	--
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(iv) Mercury)	-	750	---
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(v) Cadmium)	-	750	---
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(vi) Lead)	-	750	---
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(vii) Barium)	-	750	--
Clause 5.3 ( sub clause 5.3.3)Requirement as per Table 3/ i(viii) Selenium)	-	750	--
Clause 5.3 ( sub clause 5.3.4)Requirement as per Table 4/ i Annex G(i) N-Nitrosamines)	-	5000	--
Clause 5.3 ( sub clause 5.3.4)Requirement as per Table 4/ ii Annex G(ii) N-Nitrosatables)	-	0	--
Clause 5.3 ( sub clause 5.3.1)Requirement as per Table 1/ ii Annex C(Acetone extract, percent: a) Acetone extracted material, percent by mass, Max)	-	1750	--
Clause 5.3.1 Table 1 (v) (Extractable protein content)	-	2400	--
5.3.5(Determination of MBT)	-	2400	--
5.3.6(Determination of Antioxidants)	-	2400	--
Clause 5.4 ( sub clause 5.4.2) Tear Strength Annex K(Tear Strength)	-	1900	---
Clause 5.4 ( sub clause 5.4.3)Tensile Test Annex L(Tensile Test)	-	1900	---

-
REVISED VERSION OF IS 3565:2018 INCLUDED W.E.F. 3-6-2021.

IS 12585 (1988)

Specification for thermoplastic hoses (Textile Reinforced) for water - General purpose

Specification for Thermoplastic Hoses For water

7050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Construction)	-	300	--
Cl 4.2(Dimensions & Tolerances)	-	300	--
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	500	--
Cl 4.3.2(Adhesion)	-	950	--
Cl 4.3.3(Pressure Requirements)	-	2000	--
Cl 4.3.4(Minimum Bend Radius)	-	1000	--
Cl 4.3.5(Low Temperature Flexibility)	-	2000	--

-
-

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

SURGICAL RUBBER GLOVES

10850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.4(Manufacture)	-	300	--
4.2(Dimensions Fig 1 and Table 1)	-	300	--
4.3(Thickness)	-	300	--
4.4.1(Physical Properties)	-	950	--
4.4.2(After accelerated aging at 70 + 1OC for 240 h )	-	4950	--
4.4.3(After heat ageing in autoclave)	-	2750	--
4.4.4(Tension Set)	-	800	--
4.5(pH of Aqueous Extract )	-	500	--

-
-

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

FLEXIBLE RUBBER TUBING FOR LIQUEFIED PETROLEUM GAS

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-	100	-
Cl4.3.1(The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-	200	-
Cl4.3.2(it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-	200	-
Cl.4.4,(Cl.4.4.1)(when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-	1300	-
Cl.4.4,(Cl.4.4.2)(it shall remain atatched to both nozzles throught the test period)	-	1300	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1000	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1000	-
Cl.4.6(Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-	500	-
Cl.4.7(Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-	1000	-
Cl.4.8.1(Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-	1000	-
Cl4.8.2(The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-	1000	-
Cl.4.9(Crushing test , )	-	1000	-
Cl.4.10(Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-	2000	-
Cl.4.11(Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-	3000	-
Cl.4.12(Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-	1000	-

-
-

IS 13098 (2012)

Automotive vehicles - Tubes for pneumatic tyres - Specification (First Revision)

AUTOMOTIVE VEHICLES – TUBES FOR PNEUMATIC TYRES

17800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3/3.3(Uniformity(The Thickness shall not vary from the arithmetic mean of the readings by ± 17.5 % at any point in longitudinal direction :-Crown centre,Base centre,Side wall - 1,Side wall - 2))	-	600	--
4/4.1.1(Elongation at break (Class A' Tubes))	-	1900	--
4/4.1.1(Elongation at break (Class B' Tubes))	-	1900	--
4/4.1.2( Strength of Splice (Class A' Tubes))	-	0	--
4/4.1.2( Strength of Splice (Class B' Tubes))	-	0	--
4/4.1.3 Refer annex B(Set After Ageing(Class A' Tubes))	-	3600	--
4/4.1.3 Refer annex B(Set After Ageing(Class B' Tubes))	-	3600	--
3/3.1 (for valve refer IS 9081)(MATERIALS, FORM AND FIT)	-	0	---
4/4.1.4 Refer annex C(Accelerated Ageing(Both Class A and Class B))	-	3500	--
5(AIR TIGHTNESS)	-	600	---
6(MARKING)	-	600	---
3.2(Tube Material)	-	3800	---
3.2.1(% Rubber Hydrocarbon Content by volume)	-	3800	---

-
-

IS 15627 (2022)

Automotive Vehicles - Pneumatic Tyres for Two and Three - Wheeled Motor Vehicles - Specification First Revision

97000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.6(Tread wear Indicator)	-	3500	-
4.4(Tyre strength (Plunger test))	-	10000	-
4.5(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.3(Dynamic growth of tyre)	-	8000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.6(Tread wear Indicator)	-	3500	-
4.4(Tyre strength (Plunger test))	-	10000	-
4.5(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.3(Dynamic growth of tyre)	-	8000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.6(Tread wear Indicator)	-	3500	-
4.4(Tyre strength (Plunger test))	-	10000	-
4.5(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.3(Dynamic growth of tyre)	-	8000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.6(Tread wear Indicator)	-	3500	-
4.4(Tyre strength (Plunger test))	-	10000	-
4.5(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.3(Dynamic growth of tyre)	-	8000	-

-
Included w.e.f. 23.08.2023

IS 15636 (2022)

Automotive vehicles - Pneumatic tyres for commercial vehicles - Diagonal and radial ply

94000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1750	-
4.1(Tyre dimension- Outer diameter)	-	1750	-
4.1.1(Tread wear Indicator)	-	3000	-
4.5(Tyre strength (Plunger test))	-	20000	-
4.2(Endurance test-Change in diameter)	-	67000	-
4.3(Load & Speed test)	-	18000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1750	-
4.1(Tyre dimension- Outer diameter)	-	1750	-
4.1.1(Tread wear Indicator)	-	3000	-
4.5(Tyre strength (Plunger test))	-	20000	-
4.2(Endurance test-Change in diameter)	-	67000	-
4.3(Load & Speed test)	-	18000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1750	-
4.1(Tyre dimension- Outer diameter)	-	1750	-
4.1.1(Tread wear Indicator)	-	3000	-
4.5(Tyre strength (Plunger test))	-	20000	-
4.2(Endurance test-Change in diameter)	-	67000	-
4.3(Load & Speed test)	-	18000	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1750	-
4.1(Tyre dimension- Outer diameter)	-	1750	-
4.1.1(Tread wear Indicator)	-	3000	-
4.5(Tyre strength (Plunger test))	-	20000	-
4.2(Endurance test-Change in diameter)	-	67000	-
4.3(Load & Speed test)	-	18000	-

-
Included w.e.f. 23.08.2023

IS 15633 (2022)

Automotive vehicles - pneumatic tyres for passenger car vehicles - diagonal and radial ply

95500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.5(Tread wear Indicator)	-	3500	-
4.6(Tyre strength (Plunger test))	-	10000	-
4.3(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.4(Bead Unseating Resistance)	-	6500	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.5(Tread wear Indicator)	-	3500	-
4.6(Tyre strength (Plunger test))	-	10000	-
4.3(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.4(Bead Unseating Resistance)	-	6500	-
5(Marking)	-	500	-
4.1(Tyre dimension- Section Width)	-	1500	-
4.1(Tyre dimension- Outer diameter)	-	1500	-
4.5(Tread wear Indicator)	-	3500	-
4.6(Tyre strength (Plunger test))	-	10000	-
4.3(Endurance test)	-	57000	-
4.2(Load & Speed test)	-	15000	-
4.4(Bead Unseating Resistance)	-	6500	-

-
Included w.e.f. 23.08.2023

Bureau of Indian Standards

The National Standards Body of India

INDIAN RUBBER MATERIALS RESEARCH INSTITUTE (IRMRI)

Plot No. 254/1B, Road no. 16V, Wagle Industrial Estate, Thane, Thane, Maharashtra, 400604

2267873200 rk@irmra.org

Scope List