BIS - LIMS (Laboratory Information Management System)

GUJARAT TEST HOUSE

Plot No.292, Road No.4, G.I.D.C., Kathwada, Ahmedabad-382 430., Ahmedabad, Ahmadabad, Gujarat, 382430

9825063601 gth292@gmail.com

Scope List

Reset

25 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 14203 (2023)

FIRE RESISTING RECORD PROTECTION CABINETS SPECIFICATION Second Revision of IS 14203

FR 60, FR 120

205000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 and 6 (Table 1)(Nominal Sizes - Height)	-	10000	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	1000	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	1000	-
3 and 6 (Table 1)(Height of Pedestal)	-	1000	-
7(Designation)	-	1000	-
8.3(Locks)	-	1000	-
8.4(Handles)	-	1000	-
9(Internal Fixtures)	-	1000	-
10.1(Minimum overall thinckness of coating)	-	1000	-
10.2(Cross Hatch Test)	-	1000	-
11, Annex-B, 3.1(Fire Endurance Test)	-	101000	-
11, Annex-B, 3.2(Fire and Impact test)	-	90000	-
8.1(Cabinet Construction)	-	1000	-
8.2(Locking Mechanism)	-	1000	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	0	-
3 and 6 (Table 1)(Height of Pedestal)	-	0	-
7(Designation)	-	0	-
8.3(Locks)	-	0	-
8.4(Handles)	-	0	-
9(Internal Fixtures)	-	0	-
10.1(Minimum overall thinckness of coating)	-	0	-
10.2(Cross Hatch Test)	-	0	-
11, Annex-B, 3.1(Fire Endurance Test)	-	0	-
11, Annex-B, 3.2(Fire and Impact test)	-	0	-
8.1(Cabinet Construction)	-	0	-
8.2(Locking Mechanism)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	0	-
3 and 6 (Table 1)(Height of Pedestal)	-	0	-
7(Designation)	-	0	-
8.3(Locks)	-	0	-
8.4(Handles)	-	0	-
9(Internal Fixtures)	-	0	-
10.1(Minimum overall thinckness of coating)	-	0	-
10.2(Cross Hatch Test)	-	0	-
11, Annex-B, 3.1(Fire Endurance Test)	-	0	-
11, Annex-B, 3.2(Fire and Impact test)	-	0	-
8.1(Cabinet Construction)	-	0	-
8.2(Locking Mechanism)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	0	-
3 and 6 (Table 1)(Height of Pedestal)	-	0	-
7(Designation)	-	0	-
8.3(Locks)	-	0	-
8.4(Handles)	-	0	-
9(Internal Fixtures)	-	0	-
10.1(Minimum overall thinckness of coating)	-	0	-
10.2(Cross Hatch Test)	-	0	-
11, Annex-B, 3.1(Fire Endurance Test)	-	0	-
11, Annex-B, 3.2(Fire and Impact test)	-	0	-
8.1(Cabinet Construction)	-	0	-
8.2(Locking Mechanism)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	0	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	0	-
3 and 6 (Table 1)(Height of Pedestal)	-	0	-
7(Designation)	-	0	-
8.3(Locks)	-	0	-
8.4(Handles)	-	0	-
9(Internal Fixtures)	-	0	-
10.1(Minimum overall thinckness of coating)	-	0	-
10.2(Cross Hatch Test)	-	0	-
11, Annex-B, 3.1(Fire Endurance Test)	-	0	-
11, Annex-B, 3.2(Fire and Impact test)	-	0	-
8.1(Cabinet Construction)	-	0	-
8.2(Locking Mechanism)	-	0	-

Complete

Included w.e.f 08.11.2024

IS 15636 (2022)

Automotive vehicles - Pneumatic tyres for commercial vehicles - Diagonal and radial ply

Diagonal & Radial

74000 View breakup
Rs.79,000/- for speed category below Q Rs.74,000/- for speed category Q and above

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.2(Technical specification-Declaration)	-	0	-
5(Marking)	-	500	Tyre marking
4.1(Tyre dimension- Section Width)	-	1500	Section width
4.1(Tyre dimension- Outer diameter)	-	1500	Outer diameter
4.1.1(Tread wear Indicator)	-	500	TWI
4.5(Tyre strength (Plunger test))	-	20000	Plunger test
4.2(Endurance test-Change in diameter)	-	50000	as applicable
4.3(Load & Speed test)	-	0	as applicable
6.2.2(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
Cl. No. 4.4, Annex-A(Tread Wear Indicators)	-	0	-
4.5(Tyre strength (Plunger test))	-	0	-
4.2(Endurance test-Change in diameter)	-	0	-
4.3(Load & Speed test)	-	0	-
6.2.2(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
Cl. No. 4.4, Annex-A(Tread Wear Indicators)	-	0	-
4.5(Tyre strength (Plunger test))	-	0	-
4.2(Endurance test-Change in diameter)	-	0	-
4.3(Load & Speed test)	-	0	-
6.2.2(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
Cl. No. 4.4, Annex-A(Tread Wear Indicators)	-	0	-
4.5(Tyre strength (Plunger test))	-	0	-
4.2(Endurance test-Change in diameter)	-	0	-
4.3(Load & Speed test)	-	0	-
6.2.2(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
Cl. No. 4.4, Annex-A(Tread Wear Indicators)	-	0	-
4.5(Tyre strength (Plunger test))	-	0	-
4.2(Endurance test-Change in diameter)	-	0	-
4.3(Load & Speed test)	-	0	-

Complete

Revised Version of IS 15636:2022 Included w.e.f. 27.07.2023

IS 15633 (2022)

Automotive vehicles - pneumatic tyres for passenger car vehicles - diagonal and radial ply

76000 View breakup
Rs.79,000/- for speed category below Q Rs.74,000/- for speed category Q and above

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.2,Anx-J(Technical specification-Declaration)	-	0	-
5(Marking)	-	500	Marking
4.1(Tyre dimension- Section Width)	-	750	Section width
4.1(Tyre dimension- Outer diameter)	-	750	outer diameter
4.5(Tread wear Indicator)	-	100	TWI
4.6(Tyre strength (Plunger test))	-	8000	Plunger
4.3(Endurance test)	-	30000	Endurance
4.2(Load & Speed test)	-	30000	Load & Speed
4.4(Bead Unseating Resistance)	-	5000	Bead unseating
6.2.2,Anx-J(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
4.5(Tread wear Indicator)	-	0	-
4.6(Tyre strength (Plunger test))	-	0	-
4.3(Endurance test)	-	0	-
4.2(Load & Speed test)	-	0	-
4.4(Bead Unseating Resistance)	-	0	-
6.2.2,Anx-J(Technical specification-Declaration)	-	0	-
5(Marking)	-	0	-
4.1(Tyre dimension- Section Width)	-	0	-
4.1(Tyre dimension- Outer diameter)	-	0	-
4.5(Tread wear Indicator)	-	0	-
4.6(Tyre strength (Plunger test))	-	0	-
4.3(Endurance test)	-	0	-
4.2(Load & Speed test)	-	0	-
4.4(Bead Unseating Resistance)	-	0	-

Complete

Revised Version of IS 15636:2022 Included w.e.f. 27.07.2023

IS 15627 (2022)

Automotive Vehicles - Pneumatic Tyres for Two and Three - Wheeled Motor Vehicles - Specification First Revision

78000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 4.1.1.1, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Section Width of Tyre)	-	1500	Dimensions
Cl. No. 4.1.1.2, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Outer Diameter of Tyre)	-	0	-
Cl. No. 4.2 & E-1.2, Annex E, Table No. 13(Load/Speed Performance Test)	-	15000	Load & Speed
Cl. No. 4.3 & F-3.4, Annex F, Table No. 14(Dynamic Growth of Tyres)	-	12000	Dynamic growth
Cl. No. 4.4, G-1, G-6.1 and G-6.3, Annex G, Table No.15 to 17(Tyre Strengtrh Test (Plunger Test))	-	13000	Plunger
Cl. No. 4.5, H-4 & E-1.2 Annex H, Table No. 18(Endurance Test)	-	35000	Endurance test
Cl. No. 4.6,Annex-D(Tread Wear Indicators)	-	1000	T.W.I.
Cl. No. 5.1(a) to 5.1 (u)(Markings)	-	500	-
Cl. No. 4.1.1.1, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Section Width of Tyre)	-	0	-
Cl. No. 4.1.1.2, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Outer Diameter of Tyre)	-	0	-
Cl. No. 4.2 & E-1.2, Annex E, Table No. 13(Load/Speed Performance Test)	-	0	-
Cl. No. 4.3 & F-3.4, Annex F, Table No. 14(Dynamic Growth of Tyres)	-	0	-
Cl. No. 4.4, G-1, G-6.1 and G-6.3, Annex G, Table No.15 to 17(Tyre Strengtrh Test (Plunger Test))	-	0	-
Cl. No. 4.5, H-4 & E-1.2 Annex H, Table No. 18(Endurance Test)	-	0	-
Cl. No. 4.6,Annex-D(Tread Wear Indicators)	-	0	-
Cl. No. 5.1(a) to 5.1 (u)(Markings)	-	0	-
Cl. No. 4.1.1.1, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Section Width of Tyre)	-	0	-
Cl. No. 4.1.1.2, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Outer Diameter of Tyre)	-	0	-
Cl. No. 4.2 & E-1.2, Annex E, Table No. 13(Load/Speed Performance Test)	-	0	-
Cl. No. 4.3 & F-3.4, Annex F, Table No. 14(Dynamic Growth of Tyres)	-	0	-
Cl. No. 4.4, G-1, G-6.1 and G-6.3, Annex G, Table No.15 to 17(Tyre Strengtrh Test (Plunger Test))	-	0	-
Cl. No. 4.5, H-4 & E-1.2 Annex H, Table No. 18(Endurance Test)	-	0	-
Cl. No. 4.6,Annex-D(Tread Wear Indicators)	-	0	-
Cl. No. 5.1(a) to 5.1 (u)(Markings)	-	0	-
Cl. No. 4.1.1.1, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Section Width of Tyre)	-	0	-
Cl. No. 4.1.1.2, Annex D, Table No. 5(a), 5(b), 6(a), 6(b), 7 to 12(Tyre Dimension_Outer Diameter of Tyre)	-	0	-
Cl. No. 4.2 & E-1.2, Annex E, Table No. 13(Load/Speed Performance Test)	-	0	-
Cl. No. 4.3 & F-3.4, Annex F, Table No. 14(Dynamic Growth of Tyres)	-	0	-
Cl. No. 4.4, G-1, G-6.1 and G-6.3, Annex G, Table No.15 to 17(Tyre Strengtrh Test (Plunger Test))	-	0	-
Cl. No. 4.5, H-4 & E-1.2 Annex H, Table No. 18(Endurance Test)	-	0	-
Cl. No. 4.6,Annex-D(Tread Wear Indicators)	-	0	-
Cl. No. 5.1(a) to 5.1 (u)(Markings)	-	0	-

Complete

Revised Version of IS 15627:2022 Included w.e.f. 27.07.2023 Exclusion: Cl.4.3 (Dynamic Growth Test)

IS 550 : Part 1 (2022)

Safes: Part 1 specification Fifth Revision

D,C,CC,CCC,BB,A,A+,AA,AAA,X

230000 View breakup
Rs. 60,000/- for Class D, Rs. 230,000/- for Class C,CC,CCC, Rs. 240,000/- for Class B,BB,BBB Rs.2,65,000/- for Class A,A+,AA,AAA

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	0	-
4(Classification)	-	0	-
5.1(Dimensions)	-	5000	Class:C,CC,CCC,D Class:BB Class:A,AA,AAA,A+
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	0
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	20000	Class:C,CC,CCC,D Class:BB Class:A,AA,AAA,A+
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	90000	-
12(Fire Resistance)	-	115000	Class:C,CC,CCC Fire Endurance test & Fire & Impact test
4(Classification)	-	0	-
5.1(Dimensions)	-	0	-
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	-
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	0	-
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	0	-
12(Fire Resistance)	-	0	-
4(Classification)	-	0	-
5.1(Dimensions)	-	0	-
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	-
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	0	-
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	0	-
12(Fire Resistance)	-	0	-
4(Classification)	-	0	-
5.1(Dimensions)	-	0	-
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	-
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	0	-
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	0	-
12(Fire Resistance)	-	0	-
4(Classification)	-	0	-
5.1(Dimensions)	-	0	-
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	-
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	0	-
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	0	-
12(Fire Resistance)	-	0	-
4(Classification)	-	0	-
5.1(Dimensions)	-	0	-
5.2(Sizes)	-	0	-
5.2(Table-2)(Inside dimensions)	-	0	-
5.2(Table-2)(Tolerance on inside dimensions)	-	0	-
5.2(Table-2)(Internal volume)	-	0	-
5.2(Table-2)(Tolerance on interanal volume)	-	0	-
5.2(Table-2)(Minumum Weight)	-	0	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	0	-
5.2(Table-2)(Thickness of Door slab)	-	0	-
5.2(Table-2)(Thickness of door overbolt work)	-	0	-
5.2(Table-2)(Number of lock on the door)	-	0	-
5.2(Table-2)(Any other type of lock)	-	0	-
5.2(Table-2)(Number of bolt on hinge side)	-	0	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	0	-
5.2(Table-2)(No.of bolt at the top)	-	0	-
5.2(Table-2)(No.of bolt at the bottom)	-	0	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	0	-
5.2(Table-2)(Depth engagement of bolt)	-	0	-
6(Material declaration)	-	0	-
7(Desigantion-Delaration)	-	0	-
8.1(Body (Construction & workmanship))	-	0	-
8.2(Door (Gap))	-	0	-
8.4.1(Hinges)	-	0	-
8.4.2(Bolts)	-	0	-
8.5(Handle)	-	0	-
8.6.1(Lock (key type) Garde)	-	0	-
8.6.1(Lock (key type)classification)	-	0	-
8.6.1(Lock (key type)construction)	-	0	-
8.6.1(Lock(key type) leaver thickness)	-	0	-
8.6.1(Lock (key type)Material)	-	0	-
8.6.1(Lock (key type)corrosion protection materail)	-	0	-
8.6.1(Lock(key type) -Endurance test)	-	0	-
8.6.1(Lock(key type)-Bolt forcing test)	-	0	-
8.6.1(Lock(key type)-salt spray solution test)	-	0	-
8.6.1(Lock(key type)-key strength test)	-	0	-
8.6.1(Lock(key type) -Marking)	-	0	-
8.6.1(Lock(Key type) -Key Marking)	-	0	-
8.6.1(Mechanical combination lock -Classification)	-	0	-
8.6.1(Mechanical combination lock -Construction)	-	0	-
8.6.1(Mechanical combination lock -Metallic parts)	-	0	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	0	-
8.6.1(Mechanical combination lock -Operation test)	-	0	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	0	-
8.6.1(Mechanical combination lock -Punching attack)	-	0	-
8.6.1(Mechanical combination lock -Endurance test)	-	0	-
8.6.1(Mechanical combination lock-Salt spary test)	-	0	-
8.6.1(Mechanical combination lock-Strength test)	-	0	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	0	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	0	-
8.6.1(Mechanical combination lock-Vibration test)	-	0	-
8.6.1(Mechanical combination lock-Marking)	-	0	-
8.6.1(Any other lock)	-	0	-
8.6.4(Lock Bolt engagement)	-	0	-
8.6.5(Additional provision- retrofitting time lock)	-	0	-
8.7(Automatic re-locking device)	-	0	-
8.8(Cable hole size)	-	0	-
9(Internal fixture)	-	0	-
10(Painting)	-	0	-
10.1(Cross hatch test)	-	0	-
11.1(Marking of safe)	-	0	-
12(Burglary attack)	-	0	-
12(Fire Resistance)	-	0	-

Complete

Revised Version of IS 550(P-1):2022 Included w.e.f. 27.07.2023

IS 14562 (2014)

Fire resisting computer media protection cabinets - Specification (First Revision)

205000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(Nominal Size (Declared))	-	30000	-
3(Type)	-	0	-
4(Materail(Declaration))	-	0	-
5(Dimension & Tolerance - Nominal Size)	-	0	-
6(Designation)	-	0	-
7(Construction)	-	0	-
8(Assembly)	-	0	-
9.1(Fabrication (Thickness of Internal steelsheet))	-	0	-
9.2(Shelf)	-	0	-
9.3(Door (Thickness of steel sheet))	-	0	-
9.4(Handle)	-	0	-
9.5(Compression mechanism)	-	0	-
9.6(Weight)	-	0	-
10(Sampling (Sample quantity))	-	0	-
11(Tests - Fire Resistancy)	-	175000	-
11.6(Criteria for conformity -Fire Endurance test)	-	0	-
11.7(Test Report)	-	0	-
12.1(Paint-Coating thicknes)	-	0	-
12.2(Crotch hatch test)	-	0	-
12.3(Finish)	-	0	-
13.1(Marking)	-	0	-
13.1(Marking on keys)	-	0	-

Complete

IS 14203 (2017)

Fire resisting record protection cabinets - Specification (Second Revision)

FR 60 ,FR 120

207500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3(Nominal Sizes)	-	37500		Testing charges for Nominal sizes & general construction, Painting (exclude Fire endurance an fire & impact tests)
11.2.1(The fire resisting record protection cabinets shall be considered to be conforming to the requirements of this standard, if they pass the fire endurance test (see B-3.1) and fire and impact test (see B-3.2) if the contents (see B-1.1, B-3.1.1, B-3.2.1) kept in the cabinets during the test are found usable.)	-	1700000		Testing charges for Fire endurance test an Fire & impact test

Complete

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Grade 1 & 2

7350 View breakup
Rs. 7350/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	850	-
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	1500	-
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	1500	-
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	1000	-
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 2))	-	1500	-
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	-

Complete

IS 15636 (2012)

Automotive vehicles - Pneumatic tyres for commercial vehicles - Diagonal and radial ply - Specification (First Revision)

Diagonal & Radial

79000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Tyre Dimensions)	-	3500	(Rs.500 included for test of marking )
4.1.1(Section width of tyre)	-	1500	-
4.1.1.2(Tyre outer diameter)	-	1500	Dimensions (Cl. 4.1.1.2)-1320
4.1.3(Section width of tyre)	-	1500	Dimensions (Cl. 4.1.3)-1320
4.1.3(Outer diameter of tyre)	-	2000	Dimensions (Cl. 4.1.3)-1320
4.2(Endurance test)	-	55000	Endurance Test (Cl. 4.2)
4.3.1(Load/Speed performance test)	-	50000	Load/Speed Performance Test (Cl. 4.3)
4,4,1(Tread -wear indicators)	-	500	Tread Wear Indicators (Cl. 4.4 )
4.4,2(Tread -wear indicators)	-	500	Tread Wear Indicators (Cl. 4.4.2)-580
4.4.4(Tread -wear indicators)	-	500	Tread Wear Indicators (Cl. 4.4.4)
4.5(Tyre strength test (Plunger rest))	-	20000	Tyre Strength Test (Plunger Test) (Cl. 4.5)

Complete

IS 15633 (2005)

Automotive vehicles - Pneumatic tyres for passenger car vehicles - Diagonal and radial ply - Specification

Diagonal & Radial Ply

76000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex B Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	800	Dimensions (Cl. 4.1)-800
4/4.1.1.2- Refer Annex B Col 2 and Annex D(test method )(Tyre outer diameter)	-	800	Dimensions (Cl. 4.1)-800
4/4.2.1 /4.2.2/4.2.3,Refer Annex D ,Table 13(Load/Speed Performance Test)	-	800	Load/Speed Performance Test (Cl. 4.2)-800

Complete

IS 15627 (2005)

Automotive vehicles - Pneumatic tyres i?or two and three - Wheeled motor vehicles - Specification

Radial & Diagonal

78000 View breakup
Rs.66,000/-(For speed less than 150 Kmph); Rs.78,000/-(For speed more than 150 Kmph)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex C Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	2500	Testing charges include Tyre outer diameter ,section width, Marking
4.6.2 Refer Annex D(Method of measurement)(Tread Wear Indicators)	-	500	-
4.4,Refer Table 14 to 16 and Annex G(Tyre Strength Test (Plunger Test) )	-	13000	-
4.5 refer Table 17 and Annex H(Endurance Test)	-	30000	Endurance test charges,Rs.30000,is for Speed category above : P and for speed category : Up to :P, will be :Rs.35000.
4/4.2.1 /4.2.2/4.2.3,Annex E ,Table 12(Load/Speed Performance Test)	-	15000	-
4/4.3 Refer Annex F,Table 13(Dynamic Growth of~Tyres)	-	15000	-

Complete

Dynamic Growth Test

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

Grade I,Grade II

5450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions and tolerances)	-	200	Dimensions
10.2, Table-1(Test for Density)	-	650	Density
10.4, Table-1(Test for Water Absorption)	-	500	water Absproption
10.5(test for swelling in water)	-	800	Thickness swelling
10.6(test for modulis of rupture)	-	800	M.O.R.
10.7(Test for tensile strength perpendicular to Surface)	-	350	Tensile strength
10.8(Test for tensile strength perpendicular to Surface after ageing )	-	350	Tensile strength - Cyclic & Accelerated
10.9(test screw withdrawal strength)	-	700	Screw withdrawal
10.1(test for surface abrasion resistance)	-	700	Abrasion resistance
10.11(test for resistance to steam)	-	100	Steam resistance
10.12(test for resistance to crack)	-	100	cracking resistance
10.13(test for resistance to cigarette burn)	-	100	cigarette burn resistance
10.14(test for resistance to stain)	-	100	Stain resistance

Complete

IS 14561 (2014)

Fire resisting (Insulating) filing cabinets - Specification (Second Revision)

Vertical/ Lateral

205000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(i) Height)	-	500	IS 14561 CL 4.1
4.1(ii) Width)	-	500	IS 14561
4.1(iii) Depth)	-	500	IS 14561
4.1(iv) Height of the bottom drawer above floor level)	-	200	IS 14561
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	200	IS 14561
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	100	IS 14561
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	100	IS 14561
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	100	IS 14561
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	100	IS 14561
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	100	IS 14561
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	100	IS 14561
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	100	IS 14561
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	100	IS 14561
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	2000	IS 14561
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	100	IS 14561
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	100	IS 14561
7.8(Locking Mechanism )	-	100	IS 14561
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	100	IS 14561
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	100	IS 14561
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	100	IS 14561
8(Assemblies)	-	100	IS 14561
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	100	IS 14561
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	100	IS 14561
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	10500	IS 14561
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	100	IS 14561
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	200	IS 14561
10.2.1(Cross Hatch Test)	-	300	IS 14561
11.1(Fire endurance test)	-	2500	IS 14561
11.2(Fire and impact test)	-	2500	IS 14561
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	100	IS 14561
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	100	IS 14561

Complete

IS 13098 (2012)

Automotive vehicles - Tubes for pneumatic tyres - Specification (First Revision)

Class A , Class B

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3/3.1 (for valve refer IS 9081)(MATERIALS, FORM AND FIT)	-	150	Dimension
3/3.3(Uniformity(The Thickness shall not vary from the arithmetic mean of the readings by ± 17.5 % at any point in longitudinal direction :-Crown centre,Base centre,Side wall - 1,Side wall - 2))	-	400	Thickness variation
4/4.1.1(Elongation at break (Class A' Tubes))	-	600	Elongation
4/4.1.2( Strength of Splice (Class A' Tubes))	-	600	Strength of splice
4/4.1.3 Refer annex B(Set After Ageing(Class A' Tubes))	-	2800	Set after agening
4/4.1.4 Refer annex C(Accelerated Ageing(Both Class A and Class B))	-	2800	accelerated agening
5(AIR TIGHTNESS)	-	150	Air tightness

Complete

IS 12406 (2003)

Medium density fibre boards for general purpose - Specification (First Revision)

Solid Board Grade I Solid Board Grade II

5450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Types)	-	25	Type
Cl 7(Finish)	-	25	Finish
Cl 8(Dimensions & Tolerances)	-	250	Dimensions
Cl 11.4(Test For Density)	-	250	Density
Cl 11.5(Test For Moisture Content)	-	300	Moisture content
Cl 11.6(Test For water Absorption)	-	600	Water Absorption
Cl 11.7.1(Due To General Absorption)	-	400	General absorption
Cl 11.7.2(Due To Surfacel Absorption)	-	400	Surface absorption
Cl 11.8(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1200	MOR
Cl 11.9(Test For Internal Bond)	-	1600	Internal Bondd
Cl 11.10(Test For Screw Withdrawal Strength)	-	400	Screw withdrawal test

Complete

IS 11188 : Part 1 (2014)

Vault (Strong Room) doors: Part 1 specification (Second Revision)

C, B, A, AA, AAA

307000 View breakup
Rs.2,91,000/- (for Class C), Rs.3,07,000/- (for Class B), Rs.1,05,000/- (for Class A), Rs.1,55,000/- (for Class AA), Rs.1,95,000/- (for Class AAA)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(DIMENSIONS)	-	500	-
5 Table 1(i) Door Type)	-	50	-
5 Table 1(ii) Overall dimension of vault door)	-	50	-
5 Table 1( a) Height,H)	-	50	-
5 Table 1( b) Width W)	-	50	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	50	-
5 Table 1( a) Height H, Min b) Width W, Min iv) a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min )	-	50	-
5 Table 1( b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	50	-
5 Table 1( v) Dimension of the rebate coming under shear)	-	50	-
5 Table 1( vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	50	-
5 Table 1( vii) Diameter of grill gate rods, Min)	-	50	-
5 Table 1( viii) Pitch of grill gate rods)	-	50	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	50	-
5 Table 1(xi) Thickness of drill and oxyacetylene torch resisting layer (excluding mild steel plates),Min)	-	50	-
5 Table 1(xii) Wall thickness (recommendation))	-	50	-
5 Table 1(xiii) Number of locks)	-	50	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	50	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	50	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	50	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	50	-
5 Table 1( cross sectional area, Min,sq mm)	-	50	-
5 Table 1(xix) Depth of engagement of shooting)	-	50	-
5 Table 1( bolts, Min)	-	50	-
8( CONSTRUCTION AND GENERALREQUIREMENTS)	-	100	-
8.1 Fig. 1( Doors )	-	50	-
8.1.1( Ventilating Grill Gate (Inside))	-	50	-
8.1.2( Main Door (Outside))	-	50	-
8.2(Doors Frame)	-	50	-
8.2.1 (Rebate of the Door Frame)	-	50	-
8.2.2 (Compression Mechanism)	-	50	-
8.2.3 (Crane Hinge Mechanism)	-	50	-
8.3(Locking Mechanism)	-	50	-
8.3.1( Lock Case)	-	50	-
8.3.2 (Bolt Work)	-	50	-
8.3.2.1 Table 1.(The number of bolts and their minimum dimension)	-	50	-
8.3.2.2( Construction)	-	50	-
8.4(Lock)	-	50	-
8.4.4( Time Lock)	-	50	-
8.4.5 (Automatic Relocking Device)	-	50	-
9( DOOR FITTINGS)	-	50	-
9.1(Hinges)	-	50	-
9.1.1( Adjusting Bolt)	-	50	-
9.2( Handles)	-	50	-
9.3( Foot Bridge)	-	50	-
9.4( Vault Lighting Control)	-	50	-
10(FINISH)	-	50	-
10.3( Cross Hatch Test)	-	50	-
10.4(Alternate to Cl 10.4)	-	50	-
11(Burglary resistance IS 11188 (Part 2))	-	72000	#Note :Class-B :Rs.72000, Class-C:Rs.56000, Class-A:Rs.100000, Class-AA:Rs.150000, Class-AAA:Rs.190000.
IS 11188 (Part 2), 3.1 and 3.2( i)Net Working time, Minutes)	-	72000	#Note : As above (Burglary resistance test)
IS 11188 (Part 3) Cl4.4(Fire endurance IS 11188 (Part 3))	-	110000	Fire Endurance
IS 11188 (Part 3) Cl 4.5(Fire and stream hose IS 11188 (Part 3))	-	120000	Fire & stream hose

Complete

IS 5509 (2000)

Fire retardant plywood - Specification (Second Revision)

Type 1/ Type 2 / Type 3/ Type 4/ Type 5

8600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Type based on Flame retardant chemical used)	-	1500	-
8(a) Length)	-	50	-
8(b) Width)	-	50	-
8(c) Thickness 1) less than 6mm ±10% 2) 6 mm and above ±5% )	-	50	-
8.3 & Annex A (d) Edge Straightness 0.2% Max.)	-	100	-
9(Workmanship and finish)	-	50	-
12.2(Moisture content )	-	300	-
12.4(Glue adhesion (water resistance ))	-	500	-
12.4(Modulus of Rupture, (Along the grain direction of the face veneer))	-	750	fore Along Direction
12.4(Modulus of Rupture, (Across the grain direction of the face veneer))	-	750	For Across direction
12.3.1(Flammability )	-	1500	-
12.3.2(Flame Penetration )	-	1500	-
12.2.3(Rate of burning )	-	1500	-

Complete

IS 5244 (2020)

Safe Deposit Locker Cabinets — Specification ( Fourth Revision )

1, 1A, 2, 2A, 3, 4

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1( Types )	-	100	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1500	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1500	-
Table 1(Finish)	-	500	Thickness coating (in micron)
Cl. 7.1(Design and Manufacture)	-	100	-
Cl. 7.2(Design and Manufacture)	-	100	-
Cl. 7.3(Design and Manufacture)	-	100	-
Cl. 7.4(Design and Manufacture)	-	100	-
Cl. 7.5(Design and Manufacture)	-	100	-
Cl. 7.6(Design and Manufacture)	-	100	-
Cl. 8(Workmanship)	-	100	-
Cl. 8.2(Tolerance)	-	100	-
Cl. 9.1(Testing)	-	15000	-
Cl. 9.2(Testing)	-	100	-
Cl. 9.3(Cross Hatch Test)	-	10000	-
Cl. 10.1(Marking)	-	100	-
Cl. 10.4(Marking on Keys)	-	100	-

Complete

REVISED VERSION OF IS 5244:2020 INCLUDED W.E.F. 2-8-2021

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

Type 1 (CS) /Type 2 (CSC) /Type 3 (CSFF)

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	50	-
7.4(DIMENSIONS & TOLERANCES )	-	250	-
8.1(WORKMANSHIP AND FINISH )	-	25	-
8.3(WORKMANSHIP AND FINISH )	-	25	-
10.1.1(MOISTURE CONTENT)	-	250	-
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	400	-
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	400	-
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	400	-
10.1.4(RESISTANCE TO WATER TEST)	-	50	Plastic coating /suitable overlay observation after boiling water
10.1.5(MYCOLOGICAL TEST )	-	1000	Resistance to Micro-organisum
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	750	Glue share (Mycological test)
10.1.5.2(MYCOLOGICAL TEST )	-	750	Adhesion of Ply (Mycological test)
10.1.6(TENSILE STRENGTH)	-	1000	-
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	1500	Across & Along
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1500	Across & Along
10.1.9(RETENTION OF PRESERVATIVE)	-	1500	-

Complete

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

BWP/Decorative,Non-Decorative/Modular,Non-Modular

8450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.3(Workmanship & finish - IS 2202(Pt-1))	-	200	-
11.1(Height - IS 4020 (Pt-2))	-	50	-
11.1(Width- IS 4020 (Pt-2))	-	50	-
11.1(Thickness - IS 4020 (Pt-2))	-	50	-
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	500	-
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	500	-
11.5(Residual deflection - IS 4020(Pt-6))	-	100	-
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	100	-
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	100	-
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	100	-
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	100	-
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	200	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	250	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	250	-
11.8(Buckling Test - IS 4020(Pt-9))	-	100	-
11.8(Initial deflection - IS 4020(Pt-9))	-	100	-
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	400	-
11.9(Slamming Test - IS 4020(Pt-10))	-	100	-
11.1(Misuse Test - IS 4020(Pt-11))	-	300	-
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	3200	-
11.12(End Immersion Test - IS 4020(Pt-13))	-	800	-
11.13(Knife Test - IS 4020(Pt-14))	-	400	-
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	400	-
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	500	-

Complete

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

BWP/ MR,Decorative type / Commercial type,Thickness mm

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	100	surface defects
7.3(Dimensional Requirements - Length - 8.1.4)	-	20	Length
7.3(Dimensional Requirements - Width - 8.1.4)	-	20	Width
7.3(Dimensional Requirements - Thickness - Annexure E)	-	20	Thickness
7.3(Dimensional Requirements - Squareness - Annexure D)	-	20	Squareness
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	20	Straightness
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	250	Local planesness -Dim.stability
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	250	Delamination- Dim.stability
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	250	at 90 -Thickness change-Dim.stablity
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	250	at 40 - Thickness change-Dim.changes
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	250	at 40 length changes-Dim.stablity
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	250	at 90 length changes-Dim.stability
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	250	for MR Grade
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	250	For BWP Grade -
9.2.3(Adhesion of Plies - Annexure H)	-	100	Adhesion of Ply
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1000	For MR Grade only
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	250	MOR -Minimum
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	250	MOR -Average
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	250	MOE - Minimum
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	250	MOE -Average
9.2.6(Spot test - Annexure L)	-	2000	Spot test

Complete

IS 1328 (1996)

Veneered Decorative Plywood -Specification

Type 1/ Type 2,BWR/ MR,Thickness upto and including -mm

2700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	50	type-1
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	50	type-1
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	50	type-1
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	50	type-2
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	50	type-1
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	50	Type-2
4.2(Type - For Type 1)	-	100	type-1
4.2(Type - For Type 2)	-	100	type-2
8(Dimensions & Tolerances - Length - Cl. 8)	-	100	length
8(Dimensions & Tolerances - Width - Cl. 8)	-	100	width
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	100	Thickness
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	100	Edge straightness
8(Dimensions & Tolerances - Squareness - Annexure C)	-	100	Squarness
9(Finish - Cl. 9.1, 8.3)	-	100	Cl.9.1
9(Finish - Cl. 9.2, 8.3)	-	100	Cl.9.2
11(Tests - Moisture Content - Part 1 of IS 1734)	-	500	Moisture content
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	500	MR grade
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	500	BWR grade

Complete

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

MR,BWR,BWP

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(MR (Moisture Ressistant))	-	1200	Cyclic test for MR Grade
4 Table (i)(BWR (Boiling Water Resistant))	-	2000	Cyclic test for BWR Grade
4 Table (i)(BWP (BOiling WaterProof))	-	3000	Cyclic test for BWP Grade

Complete

IS 710 (2010)

Marine plywood - Specification (Second Revision)

For Thickness upto and including --- mm

10400 View breakup
Rs. 10400/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(WORKMANSHIP AND FINISH )	-	25	CL NO.7.1
7.2(WORKMANSHIP AND FINISH )	-	25	CL.NO.7.2
7.3(WORKMANSHIP AND FINISH )	-	25	CL.NO.7.3
7.5(WORKMANSHIP AND FINISH )	-	25	CL.NO.7.5
6.1(DIMENSIONS)	-	20	LENGTH
6.1(DIMENSIONS)	-	20	WIDTH
6.3(DIMENSIONS)	-	20	THICKNESS
6.3(DIMENSIONS)	-	20	Tolerance for Length, Width, Thickness, Squarenes, Straightness
9.1.1(MOISTURE CONTENT)	-	500	Moisture content
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	750	GSS Dry state
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	750	GSS dry state -Adhesion of ply
9.1.3 , 9.1.3.1.1(Water resistance test)	-	750	Water resistance- Glue share
9.1.3 , 9.1.3.1.2(Water resistance test)	-	750	Water resistance -Adhesion of ply
9.1.5(Mycological test)	-	500	Mycological-Resistance to micro-organism
9.1.5 , 9.1.3.1.1(Mycological test)	-	500	Mycological-Glue Share strength
9.1.5 , 9.1.3.1.2(Mycological test)	-	500	Mycological- Adhesion of Ply
9.1.4(Tensile strength)	-	1500	Tensile strength
9.1.6 (Table 3)(Static bending strength)	-	500	Static bending strength -Along
9.1.6 (Table 3)(Static bending strength)	-	500	Static bending strength-Across
9.1.7 (Table 4)(Wet bending strength)	-	1000	Wet bending -Along
9.1.7 (Table 4)(Wet bending strength)	-	1000	Wet bending-Across
9.1.8(Retention of preservative)	-	700	Type of preservative

Complete

IS 550 : Part 1 (2014)

Safes: Part 1 specification (Fifth Revision)

Double Door/ Single Door

230000 View breakup
Rs.60,000/- for Class D, Rs.2,30,000/- (for Class C, CC, CCC), Rs.2,40,000/- (for B, BB, BBB), Rs.2,65,000/- (for A, A+, AA, AAA)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4 Table 1(CLASSIFICATIONS)	-	205000	Rs.25000 for Dimension &other reqiurments+Rs35000 for Burglary test +Rs.85000 for Fire endurance test+Rs.85000 for Fire & Impact test for Class: C/CC/CCC.
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 10(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	100	-
Cl. 6 Table 3(Material)	-	100	-
Cl. 7 (DESIGNATIONS)	-	100	-
Cl. 8.1(Body)	-	100	-
Cl. 8.3(Door)	-	100	-
Cl. 8.4.1(Hinges)	-	100	-
Cl. 8.4.2(Bolts)	-	100	-
Cl. 8.5 Table 3(Handles)	-	100	-
Cl. 8.6.1(Locks (Type))	-	100	-
Cl. 8.6.1.1(Locks (Type))	-	100	-
Cl. 8.6.2(Locks (Levers))	-	100	-
Cl. 8.6.3(Tests for locks)	-	100	-
Cl. 8.6.4(Keys)	-	100	-
Cl. 8.6.5(Unpickability)	-	100	-
Cl. 8.6.6(Non-interchangeability)	-	100	-
Cl. 8.7(Automatic Relocking Device)	-	100	-
Cl. 9(INTERNAL FIXTURES)	-	100	-
Cl. 10(Painting)	-	100	-
Cl. 10(Painting)	-	100	-
Cl. 11.1(Marking of Safes)	-	100	-
Cl. 11.2( Marking on Keys)	-	100	-

Complete

Except Explosive test (X)

Bureau of Indian Standards

The National Standards Body of India

GUJARAT TEST HOUSE

Plot No.292, Road No.4, G.I.D.C., Kathwada, Ahmedabad-382 430., Ahmedabad, Ahmadabad, Gujarat, 382430

9825063601 gth292@gmail.com

Scope List