BIS - LIMS (Laboratory Information Management System)

Atmy Analytical Labs Pvt. Ltd., Faridabad

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List

Reset

328 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4432 (1988)

Specification for case hardening steels (First Revision)

25800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
TABLE-1 (Clause-5)(TITANIUM)	-	0	All elements as per Table 1:- 10000/-
TABLE-1 (Clause-5)(VANADIUM)	-	0	-
TABLE-1 (Clause-5)(NIOBIUM)	-	0	-
TABLE-1 (Clause-5)(Molybdenum)	-	0	-
TABLE-1 (Clause-5)(Chromium)	-	0	-
TABLE-1 (Clause-5)(Nickel)	-	0	-
TABLE-1 (Clause-5)( ALUMINIUM)	-	0	-
TABLE-1 (Clause-5)(SILICON)	-	0	-
TABLE-1 (Clause-5)(NITROGEN)	-	0	-
TABLE-1 (Clause-5)(MANGANESE)	-	0	-
TABLE-1 (Clause-5)(PHOSPHURS)	-	0	-
TABLE-1 (Clause-5)(SULPHUR)	-	0	-
TABLE-1 (Clause-5)( CARBON)	-	0	-
Cl. 5(Vanadium)	-	0	-
Cl. 5(Copper)	-	0	-
Cl. 5(Phosphorus)	-	0	-
Cl. 5(Sulphur)	-	0	-
Cl. 5(Molybdenum)	-	0	-
Cl. 5(Chromium)	-	0	-
Cl. 5(Nickel)	-	0	-
Cl. 5(Manganese)	-	0	-
Cl. 5(Silicon)	-	0	-
Cl. 5(Carbon)	-	0	-
4(Freedom from Defects)	-	1000	-
7(Hardness)	-	2000	-
11(Dimensional Tolerances)	-	1500	-
8(Mechanical testing)	-	5000	-
8.4(Impact testing)	-	3000	-
9(Grain Size)	-	3500	-
10(Inclusion rating)	-	3500	-
14(Additional test)	-	19900	In addition to the total charges
Cl. 5(Vanadium)	-	0	-
Cl. 5(Copper)	-	0	-
Cl. 5(Phosphorus)	-	0	-
Cl. 5(Sulphur)	-	0	-
Cl. 5(Molybdenum)	-	0	-
Cl. 5(Chromium)	-	0	-
Cl. 5(Nickel)	-	0	-
Cl. 5(Manganese)	-	0	-
Cl. 5(Silicon)	-	0	-
Cl. 5(Carbon)	-	0	-
4(Freedom from Defects)	-	0	-
7(Hardness)	-	0	-
11(Dimensional Tolerances)	-	0	-
8(Mechanical testing)	-	0	-
8.4(Impact testing)	-	0	-
9(Grain Size)	-	0	-
10(Inclusion rating)	-	0	-
14(Additional test)	-	0	-
Cl. 5(Vanadium)	-	0	-
Cl. 5(Copper)	-	0	-
Cl. 5(Phosphorus)	-	0	-
Cl. 5(Sulphur)	-	0	-
Cl. 5(Molybdenum)	-	0	-
Cl. 5(Chromium)	-	0	-
Cl. 5(Nickel)	-	0	-
Cl. 5(Manganese)	-	0	-
Cl. 5(Silicon)	-	0	-
Cl. 5(Carbon)	-	0	-
4(Freedom from Defects)	-	0	-
7(Hardness)	-	0	-
11(Dimensional Tolerances)	-	0	-
8(Mechanical testing)	-	0	-
8.4(Impact testing)	-	0	-
9(Grain Size)	-	0	-
10(Inclusion rating)	-	0	-
14(Additional test)	-	0	-
Cl. 5(Vanadium)	-	0	-
Cl. 5(Copper)	-	0	-
Cl. 5(Phosphorus)	-	0	-
Cl. 5(Sulphur)	-	0	-
Cl. 5(Molybdenum)	-	0	-
Cl. 5(Chromium)	-	0	-
Cl. 5(Nickel)	-	0	-
Cl. 5(Manganese)	-	0	-
Cl. 5(Silicon)	-	0	-
Cl. 5(Carbon)	-	0	-
4(Freedom from Defects)	-	0	-
7(Hardness)	-	0	-
11(Dimensional Tolerances)	-	0	-
8(Mechanical testing)	-	0	-
8.4(Impact testing)	-	0	-
9(Grain Size)	-	0	-
10(Inclusion rating)	-	0	-
14(Additional test)	-	0	-

25 Feb, 2027

-
Included w.e.f. 17.03.2026

IS 10773 (2025)

Wrought copper tubes for refrigeration and air-conditioning purposes Specification (Second Revision)

42500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. No.5.0(Chemical composition)	-	2800	Include all elements
Clause. No.5.0(Copper + Silver)	-	0	-
Clause. No.5.0(phophrous)	-	0	-
Clause. No.5.0(Oxygen)	-	0	-
Clause no.6.0(Manufacturer)	-	0	-
Clause no.7.0(Freedom from defects)	-	500	-
Clause no.8.0(Mechnical and properties.)	-	24800	Tensile test- 3500, Flattening test- 4000, Drift expanding test- 3500, Macroscopic examination- 3000, Hydrogen embrittlement- 10800
Clause no.9.0(Dimension and tolerance.)	-	1500	-
Clause no.10(Non destructive test.)	-	24100	Eddy current- 7800, Hydrostatic test- 10500, Pneumatic test- 5800
Clause.no.11.0(Residue test or Cleanliness test.)	-	4000	-
Clause.no.11.0(Marking)	-	0	-
Clause. No.5.0(Chemical composition)	-	0	-
Clause. No.5.0(Copper + Silver)	-	0	-
Clause. No.5.0(phophrous)	-	0	-
Clause. No.5.0(Oxygen)	-	0	-
Clause no.6.0(Manufacturer)	-	0	-
Clause no.7.0(Freedom from defects)	-	0	-
Clause no.8.0(Mechnical and properties.)	-	0	-
Clause no.9.0(Dimension and tolerance.)	-	0	-
Clause no.10(Non destructive test.)	-	0	-
Clause.no.11.0(Residue test or Cleanliness test.)	-	0	-
Clause.no.11.0(Marking)	-	0	-
Clause no.10.1(Eddy-Current Test)	-	0	-
Clause no.10.2(Hydrostatic Test)	-	0	-
Clause no.10.3("Pneumatic Test ")	-	0	-
Clause no.10.4(Microscopic Examination)	-	0	-
Clause no.10.5(Hydrogen Embrittlement Test)	-	0	-

25 Feb, 2027

-
Included w.e.f. 17.03.2026

IS 6913 (2023)

Stainless steel tubes for the food, beverage, dairy and pharmaceutical industry ï¿½ Specification

22200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Manufacture)	-	500	-
Cl-7(Heat Treatment)	-	0	-
Cl-8.1, 8.2, Table-2(C Max)	-	500	-
Cl-8.1, 8.2, Table-2(Si Max)	-	500	-
Cl-8.1, 8.2, Table-2(Mn Max)	-	500	-
Cl-8.1, 8.2, Table-2(Ni)	-	500	-
Cl-8.1, 8.2, Table-2(Cr)	-	500	-
Cl-8.1, 8.2, Table-2(Mo)	-	500	-
Cl-8.1, 8.2, Table-2(S Max)	-	500	-
Cl-8.1, 8.2, Table-2(P Max)	-	500	-
Cl-8.1, 8.2, Table-2(N Max)	-	500	-
Cl-8.1, 8.2, Table-2(Cu Max)	-	500	-
Cl-9.1, Table-4(Thickness- Welded/heavily cold worked)	-	1000	-
Cl-9.1, Table-4(Thickness-Seamless)	-	1000	-
Cl-10.1(Outside Diameter)	-	1000	-
Cl-10.2(Wall Thickness)	-	500	-
Cl-11.1(Finished tubes)	-	1500	-
Cl-11.3(Critical Surface Finish)	-	1500	-
Cl-11.4(Types of Surface Finishes)	-	0	-
Cl-12(Tensile and hardness tests)	-	5000	-
Cl-13(Reverse flattening test)	-	2500	-
Cl-14(hydrostatic test)	-	3000	-
Cl-15.1(Intergranular Corrosion Test)	-	3500	-
Cl-15.2(Flaring Test (for Seamless Tubes))	-	1500	-
Cl-15.3(Flange Test (for Welded Tubes))	-	1500	-
Cl-15.4(Flattening Test)	-	1500	-
Cl-15.5(chemical cleaning or passivation)	-	1500	-
Cl-16(Retests)	-	0	-
Cl-17(Hygienic Conditions)	-	0	-
Cl-19(Marking)	-	0	-

25 Feb, 2027

-
Included w.e.f 24.03.2026

IS 733 (2025)

Wrought Aluminium and Aluminium Alloy Bars, Rods, Sections, Extruded Tube, Hollow Sections and Profiles for General Engineering Purposes ? Specification (Fourth Revision)

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	500	-
Cl-6.1, Table-1 to 8(Fe)	-	500	-
Cl-6.1, Table-1 to 8(Cu)	-	500	-
Cl-6.1, Table-1 to 8(Mn)	-	500	-
Cl-6.1, Table-1 to 8(Mg)	-	500	-
Cl-6.1, Table-1 to 8(Cr)	-	500	-
Cl-6.1, Table-1 to 8(Zn)	-	500	-
Cl-6.1, Table-1 to 8(Ti)	-	500	-
Cl-6.1, Table-1 to 8(V)	-	500	-
Cl-6.1, Table-1 to 8(Aluminium)	-	500	-
Cl-6.2(chemical analysis)	-	0	-
Cl-7.1, 7.2 & 7.3, Table-9(Dimensions)	-	2500	-
Cl-7.1, 7.2 & 7.3, Table-9(Rm MPa)	-	2500	-
Cl-7.1, 7.2 & 7.3, Table-9(Rp0.2 MPa)	-	2500	-
Cl-7.1, 7.2 & 7.3, Table-9(Elongation , Percent)	-	2000	-
Cl-9(Dimensions and Tolerances)	-	0	-
Cl-12(Packaging and Marking)	-	0	-
Cl-7.1(Tensile test)	-	0	-
Cl-5(Freedom from Defects)	-	1000	-
Cl-6.1, Table-1 to 8(Si)	-	500	-

25 Feb, 2027

-
Included w.e.f. 10.02.2026

IS 14929 (2022)

Mixed polyolefin fibre ropes (first revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Materials)	-	1500	-
Cl-6.1(Mixed polyolefin fibre ropes)	-	1500	-
Cl-6.2(Construction and manufacture)	-	1000	-
Cl-6.2(Lay)	-	1000	-
Cl-6.2(Labelling)	-	1000	-
Cl-6.2(Packaging, invoicing and delivery length)	-	500	-
Cl-7, Table-1(Linear densitybc- Nominal ktex)	-	1500	-
Cl-7, Table-1(Linear densitybc- Tolerance %)	-	0	-
Cl-7, Table-1(Minimum breaking force de - Unspliced ropes)	-	2500	-
Cl-7, Table-1(Minimum breaking forcede- Ropes with eye-spliced terminations)	-	2500	-
Cl-7, Table-2(Linear densitybc- Nominal ktex)	-	2000	-
Cl-7, Table-2(Linear densitybc- Tolerance %)	-	0	-
Cl-7, Table-2(Minimum breaking force de- Unspliced ropes)	-	2500	-
Cl-7, Table-2(Minimum breaking forcede - Ropes with eye-spliced terminations)	-	2500	-
Cl-5(Materials)	-	0	-
Cl-6.1(Mixed polyolefin fibre ropes)	-	0	-
Cl-6.2(Construction and manufacture)	-	0	-
Cl-6.2(Lay)	-	0	-
Cl-6.2(Labelling)	-	0	-
Cl-6.2(Packaging, invoicing and delivery length)	-	0	-
Cl-7, Table-1(Linear densitybc- Nominal ktex)	-	0	-
Cl-7, Table-1(Linear densitybc- Tolerance %)	-	0	-
Cl-7, Table-1(Minimum breaking force de - Unspliced ropes)	-	0	-
Cl-7, Table-1(Minimum breaking forcede- Ropes with eye-spliced terminations)	-	0	-
Cl-7, Table-2(Linear densitybc- Nominal ktex)	-	0	-
Cl-7, Table-2(Linear densitybc- Tolerance %)	-	0	-
Cl-7, Table-2(Minimum breaking force de- Unspliced ropes)	-	0	-
Cl-7, Table-2(Minimum breaking forcede - Ropes with eye-spliced terminations)	-	0	-

25 Feb, 2027

-
Included w.e.f. 10.02.2026

IS 5175 (2022)

Fibre ropes - Polypropylene split film monofilament and multifilament PP 2 and polypropylene high tenacity multifilament PP 3 3- 4- 8- and 12- strand ropes (fourth revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6, (Table 1,2,3)(Diameter)	-	500	-
Clause 6, (Table 1,2,3)(Linear Density)	-	2000	-
Clause 6, (Table 1,2,3)(Minimum Breaking Force)	-	3000	-
5.2(Pitch or length of lay)	-	2000	-
5.1(type A: 3-strand hawser-laid rope)	-	500	-
5.1(type B: 4-strand shroud-laid rope)	-	500	-
5.1(type L: 8-strand braided rope)	-	500	-
5.1(type T: 12-strand braided rope)	-	500	-
4(Designation)	-	500	-
5.1(General requirements)	-	2500	-
5.2, ISO 9554:2019 Cl. 7.1.3(Marking and labelling, for Ref no. equal or greater than 14 only.)	-	500	-
5.2, ISO 9554:2019 Cl. 7.2(Labelling)	-	500	-
6(Physical properties)	-	5000	-
6(Physical properties)	-	0	-
Clause 6, (Table 1,2,3)(Diameter)	-	0	-
Clause 6, (Table 1,2,3)(Linear Density)	-	0	-
Clause 6, (Table 1,2,3)(Minimum Breaking Force)	-	0	-
5.2(Pitch or length of lay)	-	0	-
5.1(type A: 3-strand hawser-laid rope)	-	0	-
5.1(type B: 4-strand shroud-laid rope)	-	0	-
5.1(type L: 8-strand braided rope)	-	0	-
5.1(type T: 12-strand braided rope)	-	0	-
4(Designation)	-	0	-
5.1(General requirements)	-	0	-
5.2, ISO 9554:2019 Cl. 7.1.3(Marking and labelling, for Ref no. equal or greater than 14 only.)	-	0	-
5.2, ISO 9554:2019 Cl. 7.2(Labelling)	-	0	-
6(Physical properties)	-	0	-
6(Physical properties)	-	0	-

25 Feb, 2027

-
Included w.e.f. 17.02.2026

IS 17111 (2025)

HEAT-TREATABLE STEELS, ALLOY STEELS AND FREE-CUTTING STEELS - BALL AND ROLLER BEARING STEELS ( First Revision )

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-6.3.1(Heat-treatment condition)	-	0	-
Clause-6.3.2(Particular surface conditions)	-	1000	-
Clause-6.3.3(Traceability of the cast)	-	0	-
Clause-7.1(General- Requirements)	-	1000	-
Clause-7.2, Table 3(C)	-	500	-
Clause-7.2, Table 3(Si)	-	500	-
Clause-7.2, Table 3(Mn)	-	500	-
Clause-7.2, Table 3(P)	-	500	-
Clause-7.2, Table 3(S)	-	500	-
Clause-7.2, Table 3(Cr)	-	500	-
Clause-7.2, Table 3(Mo)	-	500	-
Clause-7.2, Table 3(Ni)	-	500	-
Clause-7.2, Table 3(V)	-	500	-
Clause-7.2, Table 3(W)	-	500	-
Clause -7.2, Table-4(Al)	-	500	-
Clause -7.2, Table-4(Cu)	-	500	-
Clause-7.3(Hardenability)	-	2000	-
Clause-7.4(Hardness)	-	1500	-
Clause-7.5.1(Austenitic grain size of case-hardening and induction-hardening bearing steels)	-	1500	-
Clause-7.5.2(Spheroidization and distribution of carbides)	-	2000	-
Clause-7.6.1(Microscopic inclusions)	-	2500	-
Clause-7.6.2(Macroscopic inclusions)	-	1500	-
Clause-7.7(Internal soundness)	-	1500	-
Clause-7.8(Surface quality)	-	1000	-
Clause-7.9(Shape, dimensions and tolerances)	-	0	-
Clause-8.2(Frequency of testing)	-	0	-
Clause-8.3.1(Verification of the hardenability and hardness)	-	0	-
Clause-8.3.2(Inspection of the surface quality)	-	500	-
Clause-8.3.3(Dimensional and shape inspection)	-	1000	-
Clause-9.1(Chemical analysis)	-	0	-
Clause-9.2(Hardness and hardenability tests)	-	0	-
Clause-10(Marking)	-	0	-
Clause-6.3.1(Heat-treatment condition)	-	0	-
Clause-6.3.2(Particular surface conditions)	-	0	-
Clause-6.3.3(Traceability of the cast)	-	0	-
Clause-7.1(General- Requirements)	-	0	-
Clause-7.2, Table 3(C)	-	0	-
Clause-7.2, Table 3(Si)	-	0	-
Clause-7.2, Table 3(Mn)	-	0	-
Clause-7.2, Table 3(P)	-	0	-
Clause-7.2, Table 3(S)	-	0	-
Clause-7.2, Table 3(Cr)	-	0	-
Clause-7.2, Table 3(Mo)	-	0	-
Clause-7.2, Table 3(Ni)	-	0	-
Clause-7.2, Table 3(V)	-	0	-
Clause-7.2, Table 3(W)	-	0	-
Clause -7.2, Table-4(Al)	-	0	-
Clause -7.2, Table-4(Cu)	-	0	-
Clause-7.3(Hardenability)	-	0	-
Clause-7.4(Hardness)	-	0	-
Clause-7.5.1(Austenitic grain size of case-hardening and induction-hardening bearing steels)	-	0	-
Clause-7.5.2(Spheroidization and distribution of carbides)	-	0	-
Clause-7.6.1(Microscopic inclusions)	-	0	-
Clause-7.6.2(Macroscopic inclusions)	-	0	-
Clause-7.7(Internal soundness)	-	0	-
Clause-7.8(Surface quality)	-	0	-
Clause-7.9(Shape, dimensions and tolerances)	-	0	-
Clause-8.2(Frequency of testing)	-	0	-
Clause-8.3.1(Verification of the hardenability and hardness)	-	0	-
Clause-8.3.2(Inspection of the surface quality)	-	0	-
Clause-8.3.3(Dimensional and shape inspection)	-	0	-
Clause-9.1(Chemical analysis)	-	0	-
Clause-9.2(Hardness and hardenability tests)	-	0	-
Clause-10(Marking)	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 13997 (2014)

Drums, large open top - Specification (First Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 (Cl 7.1 & 7.3 - Table 3 of IS 513 Part 1 : 2016)(Chemical Composition - Carbon(C) - IS 228)	-	500	-
6.1 (Cl 7.1 & 7.3 - Table 3 of IS 513 Part 1 : 2016)(Chemical Composition - Manganese(Mn) - IS 228)	-	500	-
6.1 (Cl 7.1 & 7.3 - Table 3 of IS 513 Part 1 : 2016)(Chemical Composition - Sulphur(S) - IS 228)	-	500	-
6.1 (Cl 7.1 & 7.3 - Table 3 of IS 513 Part 1 : 2016)(Chemical Composition - Phosporous(P) - IS 228)	-	500	-
5, Table 1(Dimensions-D2)	-	500	-
5, Table 1(Dimensions-D3)	-	500	-
5, Table 1(Dimensions-D4)	-	500	-
5, Table 1(Dimensions-H1)	-	500	-
5, Table 1(Dimensions-H5)	-	500	-
5, Table 1(Dimensions-h2)	-	500	-
5, Table 1(Dimensions-h3)	-	500	-
5, Table 1(Dimensions-h4)	-	500	-
5, Table 1(Dimensions-p1)	-	500	-
6.2(The nominal thickness of steel sheets for body and ends )	-	500	-
7.1( CONSTRUCTION)	-	500	-
7.1( CONSTRUCTION)	-	0	-
7.2( CONSTRUCTION)	-	250	-
7.3( CONSTRUCTION- Double Seam/Spiral Seam/Triple Seam Construction for Grade A Drums)	-	250	-
7.4( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums)	-	250	-
7.4( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums-Seam rolling layers)	-	250	-
7.4( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums-Seam rolling layers)	-	500	-
7.5( CONSTRUCTION)	-	500	-
7.6( CONSTRUCTION)	-	500	-
7.7( CONSTRUCTION)	-	500	-
7.8( CONSTRUCTION)	-	500	-
7.8( CONSTRUCTION- crest to trough gap)	-	1000	-
7.8( CONSTRUCTION- no of corrugations on the body Each side)	-	500	-
7.9(Closures)	-	500	-
7.10(a)(Closures)	-	250	-
7.10(b)(Closures)	-	250	-
7.10(c)(Closures)	-	250	-
7.10(d)(Closures)	-	250	-
7.11( Locking Ring)	-	250	-
8.1(FINISH )	-	500	-
8.2(FINISH )	-	500	-
9(leakage test)	-	2000	-
Cl. 4(CAPACITY)	-	2500	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 18471 (2025)

Fasteners - Drilling Screws with Tapping Screw Thread - Specification (first revision)

19900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	4000	-
Clause. 4.0(Thread size.)	-	1000	-
Clause. 4.0(Length)	-	1000	-
Clause.5.0(Dimenssions.)	-	2000	-
Clause.6.1(Steel drilling screws)	-	1500	-
Clause. 6.2(Stainless steel Drilling Screws)	-	2500	-
Clause. 7.0(Thhreads)	-	2500	-
Clause. 8.0(Tolerance)	-	1000	-
Clause 9.0(Finish(coating))	-	4000	-
Clause.10(Designation)	-	1000	-
Clause.10(Marking)	-	1000	-
Clause. 4.0(Dimenssions.)	-	0	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause.5.0(Dimenssions.)	-	0	-
Clause.6.1(Steel drilling screws)	-	0	-
Clause. 6.2(Stainless steel Drilling Screws)	-	0	-
Clause. 7.0(Thhreads)	-	0	-
Clause. 8.0(Tolerance)	-	0	-
Clause 9.0(Finish(coating))	-	0	-
Clause.10(Designation)	-	0	-
Clause.10(Marking)	-	0	-
Clause. 4.0(Dimenssions.)	-	0	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause.5.0(Dimenssions.)	-	0	-
Clause.6.1(Steel drilling screws)	-	0	-
Clause. 6.2(Stainless steel Drilling Screws)	-	0	-
Clause. 7.0(Thhreads)	-	0	-
Clause. 8.0(Tolerance)	-	0	-
Clause 9.0(Finish(coating))	-	0	-
Clause.10(Designation)	-	0	-
Clause.10(Marking)	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 1783 : Part 2 (2014)

Drums large, fixed ends - Specification: Part 2 grade B drums (Fourth Revision)

44500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Capacity)	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 1))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 1 D Drums Figure 2))	-	1000	-
6(Material)	-	1500	-
7(Construction)	-	1000	-
7.1(Construction)	-	1000	-
7.2(Construction)	-	1000	-
7.3(Construction)	-	1000	-
7.4(Construction)	-	1000	-
7.5(Construction)	-	1000	-
7.7(Construction)	-	1000	-
8(Finish )	-	1000	-
9.1(Leakage at air pressure )	-	2500	-
9.2(Drop Test)	-	3500	-
9.3(Hydraulic Pressure Test)	-	5500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 C Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
5(Dimensions (Type 2 D Drums Figure 2))	-	1000	-
6(Material)	-	1500	-
6(Material)	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

42500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
5(Freedom from defects , IS 5517)	-	1000	-
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	1000	-
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	4000	-
10(Grain Size - IS 4748)	-	3500	-
11.1(Inclusion Rating- IS 4163)	-	3500	-
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	4000	-
11.2(Step Down Test- IS 10138(Pt2))	-	3500	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	5000	-
12;Table 7(Hardenability Test-IS 3848)	-	3500	-
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	1000	-
16.1 a)(Additional Test; Macro etch Test)	-	2500	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	7000	-
16.1 c); Table 7(Additional Test;Hardenability Test)	-	0	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	2000	-
16.1 e)(Additional Test;Cleanliness Test-IS 10138(Pt 1to3))	-	3500	-
16.1 f)(Microstructure for machinability,including banding)	-	3000	-
16.1 g)(Hot up set for forgability)	-	2500	-
Cl 6.2 & Table 2(Carbon- IS 228(Part 1))	-	0	-
Cl 6.2 & Table 3(Sulphur- IS 228(Part 9))	-	0	-
Cl 6.2 & Table 4(Phosphorous- IS 228(Part 3))	-	0	-
Cl 6.2 & Table 5(Manganese- IS 228(Part 2))	-	0	-
Cl 6.2 & Table 6(Silicon- IS 228(Part 2))	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 19315 (2025)

Ball Valves for Water Works Purposes - Specification

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 3(TERMS AND DEFINITION)	-	100	-
As per Clause 3.1(Ambient Temperature)	-	200	-
As per Clause 3.2(Cold Working Pressure (CWP))	-	1500	-
Cl 3.3(DN)	-	1000	-
Cl 3.4(End-to-End Dimension)	-	3500	-
Cl 3.5(Face-to-Face Dimension)	-	3500	-
Cl 3.6(Full Bore Valve)	-	1000	-
Cl 3.7(Operator)	-	1000	-
Cl 3.8(PN or Class)	-	1000	-
Cl 3.9(Reduce Bore Valve)	-	1500	-
Cl 3.10(Trim)	-	1500	-
Cl 4(DESIGN)	-	500	-
Cl 4.1(Ball Valve Construction)	-	1000	-
Cl 4.2(Nominal Sizes)	-	1000	-
Cl 4.3(Rating)	-	1000	-
Cl 4.4(Valve Bore Dimensions)	-	0	-
Cl 4.5(Face-to-Face and End-to-End Dimensions)	-	0	-
Cl 4.6(Valve Ends)	-	1000	-
Cl 4.6.1(Flanged End)	-	1000	-
Cl 4.6.2(Socket Weld Ends for Stainless Steel Materials)	-	2500	-
Cl 4.6.3(Solder Ends for Copper Alloy Materials)	-	2500	-
Cl 4.6.4(Screwed Ends)	-	1000	-
Cl 4.6.4.1(Screwed end for copper alloy materials)	-	1000	-
Cl 4.6.4.2(Screwed end for stainless steel materials)	-	1000	-
Cl 4.6.5(Crimping Ends for Copper Alloy materials)	-	1000	-
Cl 4.7(Design)	-	0	-
Cl 4.7.1(General)	-	0	-
Cl 4.7.1.2("Body shell thickness for copper alloy materials ")	-	1500	-
Cl 4.7.1.3(Joint)	-	500	-
Cl 4.7.1.5(End connections)	-	500	-
Cl 4.7.1.6(Stems)	-	500	-
Cl 4.7.1.8(Stem packing)	-	500	-
Cl 4.7.1.9(Corrosion resistant coating)	-	3500	-
Cl 4.7.2(Body Shell Thickness for Steel Valves)	-	500	-
Cl 4.7.3(Body Shell Thickness)	-	500	-
Cl 4.7.4(Bolted Body Joint)	-	500	-
Cl 4.7.5(Bolted Bonnet or Cover Joint)	-	500	-
Cl 5(VALVE OPERATION)	-	1500	-
Cl 6(MATERIALS OF CONSTRUCTION)	-	1500	-
Cl 7(PERFORMANCE REQUIREMENTS)	-	7500	-
Cl 7.2(Pressure Tests for Steel Valves)	-	0	-
Cl 7.2.1(Shell Test (HYD))	-	0	-
Cl 7.2.2(Closure Test (HYD))	-	0	-
Cl 7.2.3(Closure Test (Gas))	-	0	-
Cl 7.2.4(Test Duration)	-	0	-
Cl 7.3(Pressure Tests for Copper Alloy Valves)	-	0	-
Cl 7.3.2(Closure Test)	-	0	-
Cl 7.3.1(Shell Test)	-	0	-
Cl 7.4(Test Fluid)	-	0	-
Cl 7.5(Test Gauges)	-	0	-
Cl 8(SAMPLING AND TESTING)	-	100	-
Cl 8.2(Factory Production Control)	-	0	-
Cl 9(PACKAGING)	-	100	-
Cl 10(MARKING)	-	500	-
Cl 10.1(Legibility)	-	0	-
Cl 10.2(Body Marking)	-	0	-
Cl 10.3(Identification Plate)	-	0	-

25 Feb, 2027

-
Included w.e.f. 31.12.2025

IS 18166 (2025)

Unplasticized Polyvinyl Chloride PVC-U Threaded Column Pipes for Borewells/Tubewells - Specification

41500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(COLOUR)	-	1000	Raw material Testing Charges Rs. 15000/- Additional.
6(CLASSIFICATION)	-	500	Raw material Testing Charges Rs. 15000/- Additional.
7, Table - 2,3,4,7(DIMENSIONS)	-	2500	Raw material Testing Charges Rs. 15000/- Additional.
8.3 , Table 5, 6(Basic Thread Dimensions)	-	2000	Raw material Testing Charges Rs. 15000/- Additional.
9.1(Visual Appearance)	-	1000	Raw material Testing Charges Rs. 15000/- Additional.
9.2(Resistance to External Blows at 0 °C)	-	5000	Raw material Testing Charges Rs. 15000/- Additional.
9.4(Tensile Strength)	-	6500	Raw material Testing Charges Rs. 15000/- Additional.
9.4(Elongation at Break)	-	6500	Raw material Testing Charges Rs. 15000/- Additional.
9.6(Izod Impact Strength Test)	-	5500	Raw material Testing Charges Rs. 15000/- Additional.
9.6(Izod Impact Strength Test)	-	0	Raw material Testing Charges Rs. 15000/- Additional.
9.8(Density)	-	1500	Raw material Testing Charges Rs. 15000/- Additional.
9.9(Vicat Softening Temperature)	-	2500	Raw material Testing Charges Rs. 15000/- Additional.
8.1(Column Pipes)	-	5500	Raw material Testing Charges Rs. 15000/- Additional.
8.2(Column Couplers)	-	5500	Raw material Testing Charges Rs. 15000/- Additional.
8.4(Sealing rings and elements made of elastomeric material such as EPDM,)	-	6500	Raw material Testing Charges Rs. 15000/- Additional.
9.5 , Table- 9(Ultimate Breaking Load)	-	6500	Raw material Testing Charges Rs. 15000/- Additional.
9.11(Hydrostatic Pressure Test)	-	12000	Raw material Testing Charges Rs. 15000/- Additional.
9.12(Joint Leak Pressure Test)	-	12000	Raw material Testing Charges Rs. 15000/- Additional.
9.3(Flattening Test)	-	5000	Raw material Testing Charges Rs. 15000/- Additional.
9.7(Resistance to DCM)	-	4500	Raw material Testing Charges Rs. 15000/- Additional.
9. 10(Effect on Water Lead (first extraction))	-	4500	Raw material Testing Charges Rs. 15000/- Additional.
9. 10(Effect on Water Lead (third extraction))	-	2500	Raw material Testing Charges Rs. 15000/- Additional.
9. 10(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	7500	Raw material Testing Charges Rs. 15000/- Additional.
9. 10(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	2500	Raw material Testing Charges Rs. 15000/- Additional.
9. 10(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	2500	Raw material Testing Charges Rs. 15000/- Additional.
5(COLOUR)	-	0	-
6(CLASSIFICATION)	-	0	-
7, Table - 2,3,4,7(DIMENSIONS)	-	0	-
8.3 , Table 5, 6(Basic Thread Dimensions)	-	0	-
9.1(Visual Appearance)	-	0	-
9.2(Resistance to External Blows at 0 °C)	-	0	-
9.4(Tensile Strength)	-	0	-
9.4(Elongation at Break)	-	0	-
9.6(Izod Impact Strength Test)	-	0	-
9.6(Izod Impact Strength Test)	-	0	-
9.8(Density)	-	0	-
9.9(Vicat Softening Temperature)	-	0	-
8.1(Column Pipes)	-	0	-
8.2(Column Couplers)	-	0	-
8.4(Sealing rings and elements made of elastomeric material such as EPDM,)	-	0	-
9.5 , Table- 9(Ultimate Breaking Load)	-	0	-
9.11(Hydrostatic Pressure Test)	-	0	-
9.12(Joint Leak Pressure Test)	-	0	-
9.3(Flattening Test)	-	0	-
9.7(Resistance to DCM)	-	0	-
9. 10(Effect on Water Lead (first extraction))	-	0	-
9. 10(Effect on Water Lead (third extraction))	-	0	-
9. 10(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
9. 10(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
9. 10(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
5(COLOUR)	-	0	-
6(CLASSIFICATION)	-	0	-
7, Table - 2,3,4,7(DIMENSIONS)	-	0	-
8.3 , Table 5, 6(Basic Thread Dimensions)	-	0	-
9.1(Visual Appearance)	-	0	-
9.2(Resistance to External Blows at 0 °C)	-	0	-
9.4(Tensile Strength)	-	0	-
9.4(Elongation at Break)	-	0	-
9.6(Izod Impact Strength Test)	-	0	-
9.6(Izod Impact Strength Test)	-	0	-
9.8(Density)	-	0	-
9.9(Vicat Softening Temperature)	-	0	-
8.1(Column Pipes)	-	0	-
8.2(Column Couplers)	-	0	-
8.4(Sealing rings and elements made of elastomeric material such as EPDM,)	-	0	-
9.5 , Table- 9(Ultimate Breaking Load)	-	0	-
9.11(Hydrostatic Pressure Test)	-	0	-
9.12(Joint Leak Pressure Test)	-	0	-
9.3(Flattening Test)	-	0	-
9.7(Resistance to DCM)	-	0	-
9. 10(Effect on Water Lead (first extraction))	-	0	-
9. 10(Effect on Water Lead (third extraction))	-	0	-
9. 10(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
9. 10(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
9. 10(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-

25 Feb, 2027

-
included w.e.f 30.01.2026

IS 1783 : Part 1 (2014)

Drums large, fixed ends - Specification: Part 1 grade A drums (Fourth Revision)

39500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Capacity)	-	3000	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 D Drums Figure 1))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 C Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	500	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
6(Material)	-	3000	-
7.1(Construction)	-	1000	-
7.2(Construction)	-	1000	-
7.3(Construction)	-	1000	-
7.4(Construction)	-	1000	-
7.5(Construction)	-	1000	-
7.6(Construction)	-	1000	-
8(Finish )	-	1000	-
9.1(Leakage at air pressure )	-	3000	-
9.2(Drop Test)	-	2500	-
9.3(Hydraulic Pressure Test)	-	5000	-
8.3(Finish)	-	1000	-
8.2(Finish)	-	1000	-
8.1(Finish)	-	1000	-
7.6(Closures)	-	2500	-
7.6(Closures)	-	0	-
7.5(CONSTRUCTION)	-	0	-
7.4(CONSTRUCTION)	-	0	-
7.4(CONSTRUCTION)	-	0	-
7.3(CONSTRUCTION)	-	0	-
7.2(CONSTRUCTION)	-	0	-
6, b(Thickness of ends(1.25± 0.09))	-	500	-
5, Fig 2(Type 2 D(h3: 4 min))	-	500	-
5, Fig 2(Type 2 D(D1: 571.5 ± 2))	-	1000	-
5, Fig 2(Type 2 C(h3: 4 min))	-	0	-
5, Fig 2(Type 2 C( D1: 571.5 ± 2))	-	0	-
5, Fig 1(Type 1 D(h3: 4 min))	-	0	-
5, Fig 1(Type 1 D(D1: 571.5 ± 2))	-	0	-
5, Fig 1(Type 1 C(h3: 4 min))	-	0	-
5, Fig 1(Type 1 C( D1: 571.5 ± 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 C Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
Dimensions (Type 2 D Drums Figure 2)(D3 Diameter over chime 585 Max)	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
5(Dimensions (Type 2 D Drums Figure 2))	-	500	-
6(Material)	-	0	-
4(Capacity)	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 D Drums Figure 1))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 C Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
5(Dimensions (Type 1 D Drums Figure 2))	-	0	-
6(Material)	-	0	-
7.1(Construction)	-	0	-
7.2(Construction)	-	0	-
7.3(Construction)	-	0	-
7.4(Construction)	-	0	-
7.5(Construction)	-	0	-
7.6(Construction)	-	0	-
8(Finish )	-	0	-
9.1(Leakage at air pressure )	-	0	-
9.2(Drop Test)	-	0	-
9.3(Hydraulic Pressure Test)	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 C Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
Dimensions (Type 2 D Drums Figure 2)(D3 Diameter over chime 585 Max)	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
5(Dimensions (Type 2 D Drums Figure 2))	-	0	-
6(Material)	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 12585 (2023)

SPECIFICATION FOR THERMOPLASTIC HOSES (TEXTILE REINFORCED) FOR WATER - GENERAL PURPOSE ( First Revision of IS 12585 )

39500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials and Construction)	-	3000	-
5(Materials and Construction)	-	0	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	2500	-
6.2(Concentricity)	-	1500	-
6.3(Tolerance on Length)	-	1500	-
6.4(Minimum Wall Thickness)	-	1500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	4500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	4500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	6500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	2000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	3500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	3500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	3500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	3000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	5500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	80000	Rs 80,000/- for UV resistence
7, 7.2 -Table 3(Flexibility at 23°C)	-	4000	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	5500	-

25 Feb, 2027

-
Included w.e.f. 31.12.2025

IS 18256 (2023)

Solid Round Glass Fibre Reinforced Polymer (GFRP) Bars for Concrete Reinforcement - Specification

295000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(clause 5.1)(Fibre content (mass fraction))	-	8000	-
(clause 5.2)(Glass transition temperature)	-	12500	-
(clause 5.3)(Degree of Cure)	-	8000	-
(clause 5.4.2)(Measured cross sectional area)	-	7000	-
(Table 1)("Minimum bend radius in case of bent bars")	-	12000	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	6000	-
(clause 6.2)(Tensile modulus of elasticity)	-	7000	-
(clause 6.3)(Ultimate Tensile Strain)	-	8000	-
(clause 6.4)(Transverse shear strength)	-	10000	-
(clause 6.5)(Bond Strength)	-	25000	-
(clause 6.6)(Fatigue Tensile Strength)	-	60000	-
(clause 6.7)(Creep Failure)	-	28000	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	20000	-
(clause 7.2)(Resistance to Alkaline Environment)	-	25000	-
(clause 7.3)(Longitudinal Wicking)	-	40000	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	75000	-
(clause 5.1)(Fibre content (mass fraction))	-	0	-
(clause 5.2)(Glass transition temperature)	-	0	-
(clause 5.3)(Degree of Cure)	-	0	-
(clause 5.4.2)(Measured cross sectional area)	-	0	-
(Table 1)("Minimum bend radius in case of bent bars")	-	0	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	0	-
(clause 6.2)(Tensile modulus of elasticity)	-	0	-
(clause 6.3)(Ultimate Tensile Strain)	-	0	-
(clause 6.4)(Transverse shear strength)	-	0	-
(clause 6.5)(Bond Strength)	-	0	-
(clause 6.6)(Fatigue Tensile Strength)	-	0	-
(clause 6.7)(Creep Failure)	-	0	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	0	-
(clause 7.2)(Resistance to Alkaline Environment)	-	0	-
(clause 7.3)(Longitudinal Wicking)	-	0	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	0	-
(clause 5.1)(Fibre content (mass fraction))	-	0	-
(clause 5.2)(Glass transition temperature)	-	0	-
(clause 5.3)(Degree of Cure)	-	0	-
(clause 5.4.2)(Measured cross sectional area)	-	0	-
(Table 1)("Minimum bend radius in case of bent bars")	-	0	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	0	-
(clause 6.2)(Tensile modulus of elasticity)	-	0	-
(clause 6.3)(Ultimate Tensile Strain)	-	0	-
(clause 6.4)(Transverse shear strength)	-	0	-
(clause 6.5)(Bond Strength)	-	0	-
(clause 6.6)(Fatigue Tensile Strength)	-	0	-
(clause 6.7)(Creep Failure)	-	0	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	0	-
(clause 7.2)(Resistance to Alkaline Environment)	-	0	-
(clause 7.3)(Longitudinal Wicking)	-	0	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	0	-
(clause 5.1)(Fibre content (mass fraction))	-	0	-
(clause 5.2)(Glass transition temperature)	-	0	-
(clause 5.3)(Degree of Cure)	-	0	-
(clause 5.4.2)(Measured cross sectional area)	-	0	-
(Table 1)("Minimum bend radius in case of bent bars")	-	0	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	0	-
(clause 6.2)(Tensile modulus of elasticity)	-	0	-
(clause 6.3)(Ultimate Tensile Strain)	-	0	-
(clause 6.4)(Transverse shear strength)	-	0	-
(clause 6.5)(Bond Strength)	-	0	-
(clause 6.6)(Fatigue Tensile Strength)	-	0	-
(clause 6.7)(Creep Failure)	-	0	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	0	-
(clause 7.2)(Resistance to Alkaline Environment)	-	0	-
(clause 7.3)(Longitudinal Wicking)	-	0	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	0	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 21 (2025)

Wrought Aluminium and Aluminium Alloys for Manufacture of Utensils - Specification (Fifth Revision)

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	300	-
Cl-5.1(Material)	-	500	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	500	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	500	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	500	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	500	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	500	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	500	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	500	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	500	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	500	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	500	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	500	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	500	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	500	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	500	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	500	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	500	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	500	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	500	-
Cl 5.4(Lead)	-	500	-
Cl 5.4(Cadmium)	-	500	-
Cl 5.4(Arsenic)	-	500	-
Cl-7(Dimension)	-	500	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	500	-

25 Feb, 2027

-
Included w.e.f. 27.01.2026

IS 13713 (2021)

Plastic Chairs for General Purposes - Specification ( First Revision )

22900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	500	-
5(Design)	-	400	-
6(Dimensions)	-	500	-
6 Table 1i a(Seat: Seat height)	-	500	-
6 Table 1i b(Seat: Effective seat depth)	-	500	-
6 Table 1i c(Seat: Seat width)	-	500	-
6 Table 1ii(Total height)	-	500	-
6 Table 1iii a(Total width (For chair with arms))	-	500	-
6 Table 1iii b(Total width (For chair without arms))	-	500	-
6 Table 1iv a(Total depth (For chair with arms))	-	500	-
6 Table 1iv b(Total depth (For chair without arms))	-	500	-
7(Mass)	-	400	-
8(Workmanship and finish)	-	500	-
9.1.1(Strength Test-static test)	-	500	-
9.1.1(Strength Test-fatigue test)	-	1500	-
9.1.1(Strength Test-Impact test)	-	1500	-
9.1.2(Stability Test)	-	1500	-
9.1.3(Free Fall Drop Test)	-	2000	-
9.1.4(Static Load Test for Leg Slippage and Distortion)	-	2500	-
9.1.5(Handle Impact Test)	-	1500	-
9.1.6(Vibration Test)	-	3000	-
9.1.7(Rigidity Test for Chair Shell)	-	2500	-
9.1.8(Colour Fastness to Daylight)	-	2500	-
9.1.9(Determination of Flammability by Oxygen Index)	-	2500	-

25 Feb, 2027

-
included w.e.f 09-12-2025.

IS 2365 (2024)

STEEL WIRE ROPES FOR LIFTS - MINIMUM REQUIREMENTS (Third revision)

8400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	250	-
Cl-4.1.1(Wire)	-	250	-
Cl-4.1.2(Core)	-	500	-
Cl-4.1.3(Lubricant)	-	500	-
Cl-4.2.2(Wire Joints)	-	100	-
Cl-4.2.3(Fibre Core Joints)	-	200	-
Cl-4.2.4(Lubrication)	-	250	-
Cl-4.2.5(Perforation and postformation)	-	250	-
Cl-4.2.7(Rope ends)	-	250	-
Cl-4.4(Dimensions)	-	1000	-
Cl-4.5(Minimum Breaking force)	-	1500	-
Cl-4.6(Wire tensile strength, if required by purchaser)	-	1500	-
Cl-4.7(Rope stretch)	-	500	-
Cl-5.2.1(Equipment)	-	500	-
Cl-5.2.2(Measured diameter)	-	500	-
Cl-5.2.3(Ovality)	-	500	-
Cl-5.2.4(Variation)	-	250	-
Cl-5.3(Test on rope for breaking force)	-	2000	-
Cl-5.4(Test on rope for lubricant content)	-	500	-
Cl-5.5(Test on rope for wire tensile strength)	-	1500	-
Cl-5.6(Additional test)	-	1500	-
Cl-4.1(Material)	-	0	-
Cl-4.1.1(Wire)	-	0	-
Cl-4.1.2(Core)	-	0	-
Cl-4.1.3(Lubricant)	-	0	-
Cl-4.2.2(Wire Joints)	-	0	-
Cl-4.2.3(Fibre Core Joints)	-	0	-
Cl-4.2.4(Lubrication)	-	0	-
Cl-4.2.5(Perforation and postformation)	-	0	-
Cl-4.2.7(Rope ends)	-	0	-
Cl-4.2.10, 4.2.11(Lay of Ropes)	-	0	-
Cl-4.4(Dimensions)	-	0	-
Cl-4.5(Minimum Breaking force)	-	0	-
Cl-4.6(Wire tensile strength, if required by purchaser)	-	0	-
Cl-4.7(Rope stretch)	-	0	-
Cl-5.2.1(Equipment)	-	0	-
Cl-5.2.2(Measured diameter)	-	0	-
Cl-5.2.3(Ovality)	-	0	-
Cl-5.2.4(Variation)	-	0	-
Cl-5.3(Test on rope for breaking force)	-	0	-
Cl-5.4(Test on rope for lubricant content)	-	0	-
Cl-5.5(Test on rope for wire tensile strength)	-	0	-
Cl-5.6(Additional test)	-	0	-
Cl-4.2.10, 4.2.11(Lay of Ropes)	-	0	-

25 Feb, 2027

-
Included w.e.f. 12.11.2025

IS 2556 : Part 4 (2004)

Vitreous sanitary appliances (Vitreous China) - specification: Part 4 specific requirements of wash basins

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	1500	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	1500	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	1500	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	1500	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	1500	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	1500	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	1500	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	1500	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Thickness IS 2556 (Part 1))	-	1000	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	1500	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	1500	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	1500	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	1500	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	1500	-
4(PAITERNS)	-	1000	-
4(SIZE)	-	1000	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	1000	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	1000	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	1000	-
5.2.1(DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-	1000	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-t)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-	1000	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-	1000	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-	1000	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-	1000	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-	1000	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-	1000	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-	1000	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-	1000	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-	1000	-
6.1(CONSTRUCTION)	-	1000	-
6.1(CONSTRUCTION)	-	0	-
6.1.1(CONSTRUCTION)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	1000	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.3-Table 5(CONSTRUCTION-Waste Hole)	-	1000	-
6.3(CONSTRUCTION-Waste Hole-Flange dia west fitting)	-	1000	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-	1000	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-	1000	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-	1000	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-	1000	-
6.4.3(CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-	1000	-
6.5(CONSTRUCTION-Overflow-horizontal dimension )	-	1000	-
6.5(CONSTRUCTION-Overflow-Area)	-	1000	-
6.5(CONSTRUCTION-Overflow-The rate of water supply)	-	1000	-
6.6(CONSTRUCTION-Soap Recess(es))	-	1000	-
6.7(CONSTRUCTION-Load Bearing Test)	-	1500	-
6.8(CONSTRUCTION-Chain Stay Hole-Dia)	-	1000	-
6.9(CONSTRUCTION-Pedestal)	-	1000	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-	1000	-
7(FINISH)	-	500	-
Cl-5.2.4, Table- 5 (v)(Dimensions and tolerances-Depth of overflow slot for waste outlet hole with integral overflow, h1)	-	1000	-
Clause 3 and Clause 6.4 of IS 2556 Part 1(Illumination during visual observation)	-	1000	-
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	0	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	0	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Thickness IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	0	-
4(PAITERNS)	-	0	-
4(SIZE)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	0	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	0	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Thickness IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	0	-
4(PAITERNS)	-	0	-
4(SIZE)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.2.1(DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-t)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1.1(CONSTRUCTION)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.3-Table 5(CONSTRUCTION-Waste Hole)	-	0	-
6.3(CONSTRUCTION-Waste Hole-Flange dia west fitting)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-	0	-
6.4.3(CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-	0	-
6.5(CONSTRUCTION-Overflow-horizontal dimension )	-	0	-
6.5(CONSTRUCTION-Overflow-Area)	-	0	-
6.5(CONSTRUCTION-Overflow-The rate of water supply)	-	0	-
6.6(CONSTRUCTION-Soap Recess(es))	-	0	-
6.7(CONSTRUCTION-Load Bearing Test)	-	0	-
6.8(CONSTRUCTION-Chain Stay Hole-Dia)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-	0	-
7(FINISH)	-	0	-
Cl-5.2.4, Table- 5 (v)(Dimensions and tolerances-Depth of overflow slot for waste outlet hole with integral overflow, h1)	-	0	-
Clause 3 and Clause 6.4 of IS 2556 Part 1(Illumination during visual observation)	-	0	-
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	0	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	0	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Thickness IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	0	-
4(PAITERNS)	-	0	-
4(SIZE)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.2.1(DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-t)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1.1(CONSTRUCTION)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.3-Table 5(CONSTRUCTION-Waste Hole)	-	0	-
6.3(CONSTRUCTION-Waste Hole-Flange dia west fitting)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-	0	-
6.4.3(CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-	0	-
6.5(CONSTRUCTION-Overflow-horizontal dimension )	-	0	-
6.5(CONSTRUCTION-Overflow-Area)	-	0	-
6.5(CONSTRUCTION-Overflow-The rate of water supply)	-	0	-
6.6(CONSTRUCTION-Soap Recess(es))	-	0	-
6.7(CONSTRUCTION-Load Bearing Test)	-	0	-
6.8(CONSTRUCTION-Chain Stay Hole-Dia)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-	0	-
7(FINISH)	-	0	-
Cl-5.2.4, Table- 5 (v)(Dimensions and tolerances-Depth of overflow slot for waste outlet hole with integral overflow, h1)	-	0	-
Clause 3 and Clause 6.4 of IS 2556 Part 1(Illumination during visual observation)	-	0	-
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	0	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	0	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Thickness IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	0	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	0	-
4(PAITERNS)	-	0	-
4(SIZE)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	0	-
5.2.1(DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-	0	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-t)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-	0	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-	0	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-	0	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1(CONSTRUCTION)	-	0	-
6.1.1(CONSTRUCTION)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.2(CONSTRUCTION-Tap Holes)	-	0	-
6.3-Table 5(CONSTRUCTION-Waste Hole)	-	0	-
6.3(CONSTRUCTION-Waste Hole-Flange dia west fitting)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-	0	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-	0	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-	0	-
6.4.3(CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-	0	-
6.5(CONSTRUCTION-Overflow-horizontal dimension )	-	0	-
6.5(CONSTRUCTION-Overflow-Area)	-	0	-
6.5(CONSTRUCTION-Overflow-The rate of water supply)	-	0	-
6.6(CONSTRUCTION-Soap Recess(es))	-	0	-
6.7(CONSTRUCTION-Load Bearing Test)	-	0	-
6.8(CONSTRUCTION-Chain Stay Hole-Dia)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal)	-	0	-
6.9(CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-	0	-
7(FINISH)	-	0	-
Cl-5.2.4, Table- 5 (v)(Dimensions and tolerances-Depth of overflow slot for waste outlet hole with integral overflow, h1)	-	0	-
Clause 3 and Clause 6.4 of IS 2556 Part 1(Illumination during visual observation)	-	0	-
Clause 3 and Clause 5.2 of IS 2556(Part 1)(Lead solubility test)	-	-	-
Clause 3 and Clause 9.5 of IS 2556(Part 1)(Chemical Resistance Test)	-	-	-
Clause 3 and Clause 9.6 of IS 2556(Part 1)(Resistance to staining and burning)	-	-	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	-	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	-	-
3(General requirements-Thickness IS 2556 (Part 1))	-	-	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	-	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	-	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	-	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	-	-
3(General requirements-PERFORMANCE REQUIllEMENTS-MODULUS OF RUPTURE IS 2556 (Part 1))	-	-	-
4(PAITERNS)	-	-	-
4(SIZE)	-	-	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-A)	-	-	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	-	-
5.1-Table 2(DIMENSIONS AND TOLERANCES-Functional Dimensions-B)	-	-	-
5.2.1(DIMENSIONS AND TOLERANCES-Connecting Dimensions)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d1)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-d2)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-e)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f1)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-f2)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g1)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g2)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g3)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-g4)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-r1)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-s)	-	-	-
5.2.2-Table 3(DIMENSIONS AND TOLERANCES-Connecting Dimensions-t)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-d2)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g1)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-g4)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-r1)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-s)	-	-	-
5.2.3-Table 4(DIMENSIONS AND TOLERANCES-Connecting Dimensions for Wash Basins with Centre Tap Hole-t)	-	-	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d3)	-	-	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d5)	-	-	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-d6)	-	-	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-h)	-	-	-
5.2.4-Table 5(DIMENSIONS AND TOLERANCES-Dimensions or Waste Outlet Hole-p)	-	-	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-n)	-	-	-
5.2.5-Table 6(DIMENSIONS AND TOLERANCES-Fixing Dimensions for Wall Hung Wash Basin-p)	-	-	-
6.1(CONSTRUCTION)	-	-	-
6.1(CONSTRUCTION)	-	-	-
6.1.1(CONSTRUCTION)	-	-	-
6.2(CONSTRUCTION-Tap Holes)	-	-	-
6.2(CONSTRUCTION-Tap Holes)	-	-	-
6.2(CONSTRUCTION-Tap Holes)	-	-	-
6.3-Table 5(CONSTRUCTION-Waste Hole)	-	-	-
6.3(CONSTRUCTION-Waste Hole-Flange dia west fitting)	-	-	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud)	-	-	-
6.4.1(CONSTRUCTION-Fixing Arrangements-Bracket Stud-Horizontal distance between two stud)	-	-	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Holes)	-	-	-
6.4.2(CONSTRUCTION-Fixing Arrangements-Screw Fixing-Hole dia)	-	-	-
6.4.3(CONSTRUCTION-Fixing Arrangements-Rag Bolt)	-	-	-
6.5(CONSTRUCTION-Overflow-horizontal dimension )	-	-	-
6.5(CONSTRUCTION-Overflow-Area)	-	-	-
6.5(CONSTRUCTION-Overflow-The rate of water supply)	-	-	-
6.6(CONSTRUCTION-Soap Recess(es))	-	-	-
6.7(CONSTRUCTION-Load Bearing Test)	-	-	-
6.8(CONSTRUCTION-Chain Stay Hole-Dia)	-	-	-
6.9(CONSTRUCTION-Pedestal)	-	-	-
6.9(CONSTRUCTION-Pedestal)	-	-	-
6.9(CONSTRUCTION-Pedestal)	-	-	-
6.9(CONSTRUCTION-Pedestal-The height from the floor to top of the rim of basin)	-	-	-
7(FINISH)	-	-	-
Cl-5.2.4, Table- 5 (v)(Dimensions and tolerances-Depth of overflow slot for waste outlet hole with integral overflow, h1)	-	-	-
Clause 3 and Clause 6.4 of IS 2556 Part 1(Illumination during visual observation)	-	-	-

25 Feb, 2027

-
included w.e.f 05-01-2026

IS 2556 : Part 7 (1995)

Vitreous sanitary appliances (Vitreous China) - specification: Part 7 specific requirements of accessories for sanitary appliances

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	500	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Application of Glazing-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finiah-IS 2556 (Part 1))	-	1000	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-·Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Spots. blisters and pinholes-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of WC pans,iDI lurfaco and horizontal tace of rima of we pans, Squatting pans bidets and urinals-Bubbles and specks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks-IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing mark -IS 2556 (Part 1))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Wavy finiah-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Warpages-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Service space top of slab inside of bowl, front of fascis-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Spots, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Wash Basins, Laboratory sinks and drinking fountains)-Face of intrnal, back and side-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Warpage-IS 2556 (Part 1)))	-	1000	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-General-Dislocations-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-wavy finish-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Spot, blisters and pinholes-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Bubbles and specks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Permissible blemishes or defects (Flushing cisterns, Auto cisterns and covers)-Visual surface-Polishing marks-IS 2556 (Part 1)))	-	0	-
3(General requirements-Thickness IS 2556 (Part 1))	-	1000	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-	1000	-
3(General requirements-PERFORMANCE REQUIllEMENTS-CRAZING IS 2556 (Part 1))	-	1000	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Individual IS 2556 (Part 1))	-	1000	-
3(General requirements-PERFORMANCE REQUIllEMENTS-WATER ABSORBTION - Average (IS 2556 (Part 1))	-	0	-
4(DIMENSIONS-STOP END CHANNEL WITH OUTLET-Type A )	-	1000	-
4(DIMENSIONS-STOP END CHANNEL WITH OUTLET-Type B )	-	1000	-
4(DIMENSIONS-PLAIN CHENNEL-Type A )	-	1000	-
4(DIMENSIONS-PLAIN CHENNEL-Type B )	-	1000	-
4(DIMENSIONS-PLAIN CHANNEL WITH SOCKET-Type A )	-	1000	-
4(DIMENSIONS-PLAIN CHANNEL WITH SOCKET-Type B )	-	1000	-
4(DIMENSIONS-FOOT REST )	-	1000	-
4(DIMENSIONS-Traps for Long Pattern and Orilsa Pattern Pans )	-	1000	-
4(DIMENSIONS-- Ovality permissible within the variation allowed for the dimensioN )	-	1000	-
4(DIMENSIONS-- FLOOR TRAP)	-	1000	-
4(DIMENSIONS-TYPICAL ILLUSTRATION OF VITRIOUS SHOWER ROSH)	-	1000	-
5(CONSTRUCTION)	-	500	-
6(FINISH)	-	500	-
7.1(Performance Test)	-	1500	-
7.2(FLUSHING TESTS-Toilet Paper Test-IS 2556(P-3))	-	1500	-
7.2(FLUSHING TESTS-Smudge Test-IS 2556(P-3))	-	1500	-
7.2(FLUSHING TESTS-Water Holding Capacity -Test-IS 2556(P-3))	-	1500	-
7.2(FLUSHING TESTS-Saw Dust Test-IS 2556(P-3))	-	1500	-
7.2(FLUSHING TESTS-Splash Test-IS 2556(P-3))	-	1500	-

25 Feb, 2027

-
Included w.e.f 13.11.2025

IS 2556 : Part 6 (2021)

Vitreous China sanitary appliances - Specification: Part 6 Specific requirements of urinal and partition plates (fifth revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(GENERAL REQUIREMENTS)	-	500	-
Cl 5(PATTERNS AND SIZES)	-	500	-
Cl 6.1(DIMENSIONS AND TOLERANCES)	-	1000	-
Cl 6.2(DIMENSIONS AND TOLERANCES)	-	1000	-
Cl 6.3(DIMENSIONS AND TOLERANCES)	-	1000	-
Cl 7(CONSTRUCTION)	-	500	-
Cl 7.1(Wall-hung urinal (flat back) with flushing rim (see Fig. 1) and wall-hung urinal (angle back) with flushing rim (see Fig. 3) shall have an integral flushing box rim with minimum 12 holes, well distributed in the rim to ensure satisfactory flushing. It shall have an integral outlet and overflow.)	-	1500	-
Cl 7.1.2()	-	1500	-
Cl 7.2()	-	1500	-
Cl 7.3()	-	1500	-
Cl 7.4()	-	1500	-
Cl 7.5()	-	1500	-
Cl 7.6()	-	1500	-
Cl 7.7()	-	1500	-
Cl 7.8()	-	1500	-
Cl 8()	-	1500	-
Clause 4 and Clause 9.3 of IS 2556 (Part 1)(Water absorption)	-	1000	-
Clause 4 and Clause 5.2 of IS 2556 (Part 1)(Lead solubility test)	-	1000	-
Clause 4 and Clause 7 of IS 2556 (Part 1)(Minimum thickness)	-	1000	-
Clause 4and Clause 9.1 of IS 2556 (Part 1)(Warpage)	-	1000	-
Clause 4and Clause 9.2 of IS 2556 (Part 1)(Crazing)	-	1000	-
Clause 4 and Clause 9.4 of IS 2556 (Part 1)(Modulus of Rupture)	-	2500	-
Clause 4 and Clause 9.5 of IS 2556 (Part 1)(Chemical resistance)	-	1500	-
Clause 4 and Clause 9.6 of IS 2556 (Part 1)(Resistance to staining and burning)	-	1500	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General-Wavy finish)	-	1500	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General-Warpage)	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General- Other appliances)	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General- Accessories)	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General- Bit)	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)(General- Discoloration)	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Flushing surface and horizontal face of rims of WC pans, squatting pans, bidets and urinals- Spots, blisters and pinholes")	-	1500	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Flushing surface and horizontal face of rims of WC pans, squatting pans, bidets and urinals-Bubbles and specks")	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Flushing surface and horizontal face of rims of WC pans, squatting pans, bidets and urinals-Polishing marks")	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Visible surfaces other than above-Spots, blisters and pinholes ")	-	1500	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Visible surfaces other than above-Bubbles and specks")	-	0	-
Clause 4 and Clause 6.1, 9.1 and 10.1 Table 1 of IS 2556 (Part 1)("Visible surfaces other than above-Polishing marks")	-	0	-
Clause 4 and Clause 5 of of IS 2556 (Part 1)(Application of glazing)	-	1500	-
Clause 4 and Clause 6.4 of IS 2556 (Part 1)(Illumination during visual observation)	-	1000	-

25 Feb, 2027

-
Included w.e.f 13.11.2025

IS 2556 : Part 3 (2024)

Vitreous China Sanitary Appliances - Specification Part 3 Specific Requirements of Squatting Pans (sixth revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3(GENERAL REQUIREMENTS)	-	1000	-
Cl-5(CONSTRUCTION)	-	500	-
Cl-6.1, Table-1 (i)(Length)	-	1000	-
Cl-6.1, Table-1 (ii)(Length of opening, &fin)	-	1000	-
Cl-6.1, Table-1 (iii)(Height)	-	1000	-
Cl-6.1, Table-1 (iv)(Width of opening, small end)	-	1000	-
Cl-6.1, Table-1 (v)(Width of opening, wide end)	-	1000	-
Cl-6.1, Table-1 (vi)(Slope of bottom of pan)	-	1000	-
Cl-6.1, Table-1 (vii)("Distance between the centre of outlet to the inside face of flushing rim at the back, Mm")	-	1000	-
Cl-6.1, Table-1 (viii)(Width)	-	1000	-
Cl-6.1, Table-1 (ix)(Length of footrest)	-	1000	-
Cl-6.2,(Connecting Dimensions)	-	1000	-
Cl-7(FINLSH)	-	500	-
Cl-8(FLUSHING TESTS)	-	1500	-
Cl-8.1(Toilet Paper Test)	-	1500	-
Cl-8.2(Smudge Test)	-	1500	-
Cl-8.3(Water Holding Capacity Test)	-	1500	-
Cl-8.4(Saw Dust Test)	-	1500	-
Cl-8.5(Splash Test)	-	1500	-
Cl-10(Marking)	-	500	-

25 Feb, 2027

-
Included w.e.f 13.11.2025

IS 2556 : Part 2 (2024)

Vitreous China Sanitary Appliances âSpecification Part 2 Specific Requirements of Washdown Water Closets (Sixth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3(GENERAL REQUIREMENTS)	-	500	-
Cl-4(PATTERNS)	-	500	-
Cl-7(FINISH)	-	500	-
Cl-5(DIMENSIONS AND TOLERANCES)	-	1000	-
Cl-6(CONSTRUCTIONS)	-	1000	-
Cl-8.1(Toilet Paper Test)	-	1500	-
Cl-8.2(Smudge Test)	-	1500	-
Cl-8.3(Holding Capacity Test)	-	1500	-
Cl-8.4.1(Single Ball Test)	-	2500	Cl. 8.4.1 + Cl. 8.4.2 - Total 2500 Rs/-
Cl-8.4.2(Fifty Ball Test)	-	2500	Cl. 8.4.1 + Cl. 8.4.2 - Total 2500 Rs/-
Cl-8.5(Load Bearing Test)	-	2500	-
Cl-8.6(Saw Dust Test)	-	1500	-
Cl-8.7(Splash Test)	-	1500	-
Cl-10("ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY")	-	1000	-
Cl-11(Marking)	-	500	-
As per Clause 3(General requirements: - Material and manufacture IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements: - Application of Glazing IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements: -Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Wavy finish as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Warpage as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Bit as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-General-Discoloration as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of rims of WC pans, Squatting pans bidets and urinals-Spots, blisters and pinholes as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of rims of WC pans, Squatting pans bidets and urinals-bubbles and specks as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC pans, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Flushing surface and horizontal face of rims of WC pans, Squatting pans bidets and urinals-polishing marks as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Spots, blisters and pinholes as per 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Bubbles and specks as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements-Permissible blemishes or defects (WC apns, Bidets, Squatting pans, Urinals, Partition plates, Pedestals, Short Pedestals and Accessories)-Visible surfaces other than above-Polishing Marks as per IS 2556 (Part 1))	-	0	-
As per Clause 3(General requirements - Minimum Thickness as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements - Warpage as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements - Crazing as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements - Water Absorption as per IS 2556 (Part 1))	-	1000	-
As per Clause 3(General requirements - Modulus of Rupture as per IS 2556 (Part 1))	-	1500	-
As per Clause 3(General requirements - Chemical Resistance Test as per IS 2556 (Part 1))	-	1500	-
As per Clause 3(General requirements - Resistance to Staining and Burning as per IS 2556 (Part 1))	-	1500	-
As per Clause 4(Patterns)	-	0	-
As per Clause 5 - Table 1 - i)(Height - A)	-	500	-
As per Clause 5 - Table 1 - ii)(Depth of water seal, Min - H)	-	1000	-
As per Clause 5 - Table 1 - iii)(Width of water closet - J)	-	1000	-
As per Clause 5 - Table 1 - iv)(Distance from centre of seat bolt hole to front of water closet - K)	-	1000	-
As per Clause 5 - Table 1 - v)(Distance from centre of seat bolt hole to inside face of flush rim at back, Max - L)	-	1000	-
As per Clause 5 - Table 1 - vi)(Distance between a vertical line from tip of back plate to inside face of flush rim at back, Max - O)	-	1000	-
As per Clause 5 - Table 1 - vii)(Width of opening, Min - P)	-	1000	-
As per Clause 5 - Table 1 - viii)(Length of opening, Min - Q)	-	1000	-
As per Clause 5 - Table 1 - ix)(Overall length - S)	-	1000	-
As per Clause 5 - Table 1 - x)(Trap inlet depth, Min - T)	-	1000	-
As per Clause 5 - Table 1 - xi)(Water surface Back to front - W1)	-	1000	-
As per Clause 5 - Table 1 - xi)(Water surface Side to side - W2)	-	1000	-
As per Clause 5 and 6 - Table 2 - i)(Height of centre line of flush inlet floor level, (for P-trap only) - B)	-	1000	-
As per Clause 5 and 6 - Table 2 - ii)(Height of centre line of outlet from floor level, (for P-trap only) - C1)	-	1000	-
As per Clause 5 and 6 - Table 2 - iii)(Distance from end of trap to floor (for S-trap only) - C2)	-	1000	-
As per Clause 5 and 6 - Table 2 - iv)(Internal diameter of outlet, Min - D)	-	1000	-
As per Clause 5 and 6 - Table 2 - v)(External diameter of outlet - D1)	-	1000	-
As per Clause 5 and 6 - Table 2 - vi)(Radius of free space (to be measured from the centre of the outlet, taken at a distance 40 mm from the end of the outlet), Min - D2/2)	-	1000	-
As per Clause 5 and 6 - Table 2 - vii)(Internal diameter of inlet - E2)	-	1000	-
As per Clause 5 and 6 - Table 2 - viii)(Depth of inlet F socket, Min - F)	-	1000	-
As per Clause 5 and 6 - Table 2 - ix)(Distance between end of flush inlet socket and outside of the outlet - G)	-	1000	-
As per Clause 5 and 6 - Table 2 - ix)(Distance between end of flush inlet socket and outside of the outlet - G1)	-	1000	-
As per Clause 5 and 6 - Table 2 - x)(Distance between end of flush inlet socket and centre line of the outlet- G2)	-	1000	-
As per Clause 5 and 6 - Table 2 - x)(Distance between end of flush inlet socket and centre line of the outlet - G3)	-	1000	-
As per Clause 5 and 6 - Table 2 - xi)(Diameter of seat bolt hole - M)	-	1000	-
As per Clause 5 and 6 - Table 2 - xii)(Distance between centre of seat bolt holes - N)	-	1000	-
As per Clause 5 and 6 - Table 2 - xiii)(Length of grooved part of outlet, Min - R)	-	1000	-
As per Clause 5 and 6 - Table 2 - xiv)(Length of straight part of outlet glazed and without groove - R1)	-	1000	-
As per Clause 5 and 6 - Table 2 - xv)(Angle of outlet (for P-trap only) - ∅)	-	1000	-
As per Clause 5 and 6 - Table 2 - xvi)(Distance between end of outlet and floor - X)	-	1000	-
As per Clause 5 and 6 - Table 2 - xvii)(Length of outlet without grooves- Y)	-	1000	-
As per Clause 5 and 6 - Table 2 - xviii)(Length of outlet extending to the floor - Y1)	-	1000	-
As per Clause 6.1(CONSTRUCTION)	-	0	-
As per Clause 6.2(CONSTRUCTION)	-	0	-
As per Clause 6 - 6.3(CONSTRUCTION)	-	0	-
As per Clause 6.4(CONSTRUCTION)	-	0	-
As per Clause 7(FINISH)	-	0	-
As per Clause 8.1(Flushing tests - Toilet Paper Test)	-	0	-
As per Clause 8.2(Flushing tests - Smudge Test)	-	0	-
As per Clause 8.3(Flushing tests - Holding Capacity Test)	-	0	-
As per Clause 8.4.1(Flushing tests - Single Ball Test)	-	0	-
As per Clause 8.4.2(Flushing tests - Fifty Ball Test)	-	0	-
As per Clause 8.5(Load Bearing Test)	-	0	-
As per Clause 8.6(Flushing tests - Saw Dust Test)	-	0	-
As per Clause 8.7(Flushing tests - Splash Test)	-	0	-
As per Clause 10(Additional requirements for water effeciency as per IS 17650 part 1)	-	0	-
Cl 4(PATTERNS)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
(Cl.6) & Cl.6.1(CONSTRUCTIONS)	-	0	-
Cl 6.2(CONSTRUCTIONS)	-	0	-
Cl 6.3(CONSTRUCTIONS)	-	0	-
Cl 6.3(Dimensions and constructions)	-	0	-
Cl 6.3(Dimensions and constructions)	-	0	-
Cl 6.3(Dimensions and constructions)	-	0	-
Cl 6.3(Dimensions and constructions)	-	0	-
Cl 6.3(Dimensions and constructions)	-	0	-
Cl 6.4(CONSTRUCTIONS)	-	0	-
Cl 6.4.1(CONSTRUCTIONS)	-	0	-
Cl 7(FINISH)	-	0	-
Cl 8 & 8.1(FLUSHING TESTS , toilet paper test)	-	0	-
Cl 8.2(Smudge Test :)	-	0	-
Cl 8.3(Holding Capacity Test :)	-	0	-
Cl 8.4 & 8.4.1(Ball test & single ball test:)	-	0	-
Cl 8.4.2(Fifty ball test :)	-	0	-
Cl 8.5(Load bearing test :)	-	0	-
Cl 8.6(Saw dust test :)	-	0	-
Cl 8.7(Splash test :)	-	0	-
(Cl. 6) of IS 2556 : 1 (2004)(Permissible blemishes of defects)	-	0	-
(Cl. 6) of IS 2556 : 1 (2004) Cl.7(Min thickness)	-	0	-
Cl-3(GENERAL REQUIREMENTS)	-	500	-
Cl-5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl-6(CONSTRUCTIONS)	-	0	-
Cl-7(FINISH)	-	0	-
Cl-8.1(Toilet Paper Test)	-	0	-
Cl-8.2(Smudge Test)	-	0	-
Cl-8.3(Holding Capacity Test)	-	0	-
Cl-8.4.1(Single Ball Test)	-	0	-
Cl-8.4.2(Fifty Ball Test)	-	0	-
Cl-8.5(Load Bearing Test)	-	0	-
Cl-8.6(Saw Dust Test)	-	0	-
Cl-8.7(Splash Test)	-	0	-
Cl-10(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	0	-
Cl-10(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	0	-
Cl-11(Marking)	-	0	-
Cl-5, Table-1 (i)(Water surface-Side to side)	-	1000	-

25 Feb, 2027

-
Included w.e.f 13.11.2025

IS 209 (2024)

Refined Zinc - Specification (Fifth Revision)

ALL

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Zinc))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Lead))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Iron))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Cadmium))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Aluminium))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Copper))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Tin))	-	1000	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Total of All Impurities))	-	1500	-
Cl 9.1(Freedom from Defect)	-	1500	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Zinc))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Lead))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Iron))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Cadmium))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Aluminium))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Copper))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Tin))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Total of All Impurities))	-	0	-
Cl 9.1(Freedom from Defect)	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Zinc))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Lead))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Iron))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Cadmium))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Aluminium))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Copper))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Tin))	-	0	-
Cl 7.1, Cl 7.2 & Table 1(Chemical Composition (Total of All Impurities))	-	0	-
Cl 9.1(Freedom from Defect)	-	0	-

25 Feb, 2027

-
Included w.e.f 13.11.2025

IS 17631 (2022)

Work Chairs - Specification

All

79000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
clause 4(DESIGN AND WORKMANSHIP)	-	4500	-
clause 5(DIMENSIONS)	-	2500	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	1000	-
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	1500	-
Cl-7.3.1(Front Edge Overturning)	-	5500	-
Cl-7.3.2(Forwards Overturning)	-	5000	-
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	5500	-
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	8000	-
Cl-6.1 (b)(Pencil hardness)	-	1000	-
Cl-6.1 (c)(Resistance to wet heat;)	-	1000	-
Cl-6.1 (d)(Resistance to dry heat;)	-	1500	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	1500	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	1500	-
Cl-6.1 (g)(Adhesive performance)	-	1000	-
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	1000	-
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	500	-
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	1500	-
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	1500	-
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	2000	-
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	2000	-
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	1000	-
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	500	-
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	1000	-
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	1000	-
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	1500	-
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	1000	-
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	1000	-
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	1500	-
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	1000	-
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	1000	-
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	1500	-
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	1000	-
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	1500	-
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	1000	-
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	1000	-
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	4500	-
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	1500	-
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	1500	-
Cl-7.4.1(Seat Front Edge Static Load Test)	-	1500	-
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	2000	-
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	2000	-
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	1500	-
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	2500	-
Cl-7.4.6(Foot Rest Static Load Test)	-	2000	-
Cl-7.5.1(Seat and Back Durability)	-	21000	-
Cl-7.5.2(Arm Rest Durability)	-	20000	-
Cl-7.5.3(Swivel Test)	-	18000	-
Cl-7.5.4(Foot-rest Durability)	-	15000	-
Cl-7.5.5(Castor and Chair-Base Durability)	-	18000	-

25 Feb, 2027

-
-

IS 17634 (2022)

Storage Units - Specification

33000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 5(DIMENSIONS)	-	4500	-
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	5500	-
CLAUSE 6(SURFACE PERFORMANCE)	-	9000	-
CLAUSE 7.1(SAFETY TESTS (General))	-	1000	-
CLAUSE 7.2(Test for Non-Movable Parts)	-	0	-
CLAUSE 7.2.1(Shelves)	-	2500	-
CLAUSE 7.2.1.2(Deflection of shelves)	-	2500	-
CLAUSE 7.2.2.1(Sustained load test for tops and bottoms)	-	2500	-
CLAUSE 7.2.2.2(Static load test for tops and bottoms)	-	2500	-
CLAUSE 7.2.3.1(Strength of clothes-rail supports)	-	2500	-
CLAUSE 7.2.3.2(Dislodgement of clothes rail)	-	2500	-
CLAUSE 7.2.4.2(Drop test)	-	2500	-
CLAUSE 7.2.4.3(Tests for units with castors or wheels)	-	2500	-
CLAUSE 7.3.1(Pivoted Doors)	-	2500	-
CLAUSE 7.3.1.2.1(Vertical load on pivoted door)	-	2500	-
CLAUSE 7.3.1.2.2(Horizontal load on pivoted door)	-	2500	-
CLAUSE 7.3.1.3(Slam-shut test of pivoted doors)	-	2500	-
CLAUSE 7.3.1.4(Durability of pivoted doors)	-	2500	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	4500	-
Cl-6.1 (b)(Pencil hardness)	-	1500	-
Cl-6.1 (c)(Resistance to wet heat)	-	9000	-
Cl-6.1 (d)Cl-6.1 (d)(Resistance to dry heat)	-	9000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats Resistance to marking by cold oils and fats)	-	3000	-
Cl-6.1 (g)(Adhesive performance)	-	3500	-
Cl-6.2 (a) 1(Breaking load)	-	2500	-
Cl-6.2 (a) 2(Elongation at break)	-	2500	-
Cl-6.2 (a) 3(Tear strength)	-	2500	-
Cl-6.2 (a) 4(Colour fastness to light)	-	5000	-
Cl-6.2 (a) 5(Colour fastness to rubbing)	-	2500	-
Cl-6.2 (a) 6(Colour fastness to perspiration)	-	1500	-
Cl-6.2 (a) 7(Colour fastness to water)	-	1500	-
Cl-6.2 (a) 8(Pilling resistance)	-	2500	-
Cl-6.2 (a) 9(Coating adhesion strength)	-	2500	-
Cl-6.2 (a) 10(Seam slippage)	-	2500	-
Cl-6.2 (a) 11(Resistance to damage by flexing)	-	2500	-
Cl-6.2 (a) 12(Abrasion resistance)	-	3000	-
Cl-6.2 (a) 13(Bursting strength)	-	1500	-
Cl-6.2 (a) 14(Resistance to cold)	-	2000	-
Cl-6.2 (b) 1(Tear strength)	-	2500	-
Cl-6.2 (b) 2(Flexing endurance)	-	4000	-
Cl-6.2 (b) 3(Finish adhesion)	-	2500	-
Cl-6.2 (b) 4(Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) 5(Colour fastness to rubbing)	-	2500	-
Cl-6.2 (b) 6(Colour fastness to water spotting)	-	1500	-
Cl-6.2 (b) 7(Water vapour permeability)	-	1500	-
Cl-6.2 (b) 8(Colour fastness to water)	-	1500	-
Cl-7.1(General)	-	1000	-
Cl-7.2.1(Shelves)	-	2500	-
Cl-7.2.2(Tops and Bottoms)	-	2500	-
Cl-7.2.3(Strength of Clothes Rails and their Supports)	-	2500	-
Cl-7.2.4(Strength of the Structure)	-	2500	-
Cl-7.3.1(Pivoted Doors)	-	2500	-
Cl-7.3.2(Sliding Doors and Horizontal Roll-fronts)	-	2500	-
Cl-7.3.3(Flaps)	-	2500	-
Cl-7.3.4(Vertical Roll-Fronts)	-	2500	-
Cl-7.3.5(Extension Elements)	-	2500	-
Cl-7.3.6(Locking and Latching Mechanism Test)	-	2500	-
Cl-7.3.7(Pull Force Test)	-	2500	-
Cl-7.3.8(Top Load Ease Cycle Test)	-	2500	-
Cl-7.3.9(Durability Test for Units with Seating Surfaces – Cyclic Impact)	-	2500	-
Cl-7.3.10(Drop Test – Dynamic – for Units with Seat Surfaces)	-	2500	-
Cl-7.4.1(Units Not Supported by the Floor)	-	2500	-
Cl-7.4.2(Units Supported by the Floor)	-	2500	-
Cl-7.5.1(General)	-	2500	-
Cl-7.5.2(Doors, Extension Elements and Flaps Closed, All Storage Units Unloaded)	-	2500	-
Cl-7.5.3(Opening Doors, Extension Elements and Flaps, All Storage Units Unloaded)	-	2500	-
Cl-7.5.4(Doors, Extension Elements and Flaps Opened and Unlocked)	-	2500	-
Cl-7.5.5(Doors, Extension Elements and Flaps Closed and Locked, All Storage Units Loaded)	-	2500	-
Cl-7.5.6(Vertical Force Stability Test for Storage Units)	-	2500	-
Cl-7.5.7(Stability Test for Pedestals/Storage Units with Seat Surfaces)	-	2500	-
Cl-7.5.8(Dynamic Stability Test for Units with Castors)	-	2500	-
Cl-7.5.9(Strength Test for Wall Attachments)	-	2500	-
Cl-9(Marking)	-	0	-
CLAUSE 7.3.2(Sliding Doors and Horizontal Roll-fronts)	-	2500	-
CLAUSE 7.3.2.2(Slam shut/open test of sliding doors and horizontal roll-fronts)	-	2500	-
CLAUSE 7.3.2.3(Durability of sliding doors and horizontal roll-fronts)	-	2500	-
CLAUSE 7.3.3(Flaps)	-	2500	-
CLAUSE 7.3.3.1(Strength of bottom-hinged flaps)	-	2500	-
CLAUSE 7.3.3.2(Durability of flaps)	-	2500	-
CLAUSE 7.3.3.3(Drop test for top-hinged flaps)	-	2500	-
CLAUSE 7.3.4(Vertical Roll-Fronts)	-	2500	-
CLAUSE 7.3.4.1(Slam shut/open test of vertical roll-fronts)	-	2500	-
CLAUSE 7.3.4.2(Durability of vertical roll-fronts)	-	2500	-
CLAUSE 7.3.5(Extension Element)	-	2500	-
CLAUSE 7.3.5.2(Strength of extension elements)	-	2500	-
CLAUSE 7.3.5.3(Durability of extension elements)	-	2500	-
CLAUSE 7.3.5.4(Slam shut/open test of extension element)	-	2500	-
CLAUSE 7.3.5.5(Displacement of extension element bottoms)	-	2500	-
CLAUSE 7.3.5.6(Interlock test)	-	2500	-
CLAUSE 7.3.6(Locking and Latching Mechanism Tests)	-	2500	-
CLAUSE 7.3.6.2(Strength test for locking and latching mechanisms for extension elements)	-	2500	-
CLAUSE 7.3.6.3(Locking and latching mechanisms for doors, flaps and roll-fronts)	-	2500	-
CLAUSE 7.3.6.4(Durability test of locking and latching mechanisms)	-	2500	-
CLAUSE 7.3.7(Pull Force Test)	-	2500	-
CLAUSE 7.3.7(Pull Force Test)	-	2500	-
CLAUSE 7.3.8(Top Load Ease Cycle Test)	-	2500	-
CLAUSE 7.3.9(Durability Test for Units with Seating Surfaces – Cyclic Impact)	-	2500	-
CLAUSE 7.3.10("Drop Test – Dynamic – for Units with Seat Surfaces")	-	2500	-
CLAUSE 7.4.1.3(Sustained load test (overload))	-	2500	-
CLAUSE 7.4.1.4(Dislodgement test)	-	2500	-
CLAUSE 7.5(Stability Tests)	-	2500	-
CLAUSE 7.5.2.1("Units that can be adjusted to a Height of 1 000 mm or less")	-	2500	-
CLAUSE 7.5.2.2("Units that can be adjusted to a height of more than 1 000 mm")	-	2500	-
CLAUSE 7.5.3(Opening Doors, Extension Elements and Flaps, All Storage Units Unloaded)	-	2500	-
CLAUSE 7.5.6(Vertical Force Stability Test for Storage Units)	-	2500	-
CLAUSE 7.5.7(Stability Test for Pedestals/Storage Units with Seat Surfaces)	-	2500	-
CLAUSE 7.5.8("Dynamic Stability Test for Units with Castors")	-	2500	-
CLAUSE 7.5.9(Strength Test for Wall Attachments)	-	2500	-

25 Feb, 2027

-
-

IS 17514 (2025)

Reusable Sanitary Pad/Sanitary Napkin/Period Panties - Specification (First Revision)

15900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Material- cover or the top sheet)	-	500	-
Cl-3.2(Material- absorbent core;)	-	500	-
Cl-3.3(Material- bottom layer.)	-	500	-
Cl-4(MANUFACTURE, WORKMANSHIP AND FINISH)	-	500	-
Cl-5(FASTENING MECHANISM)	-	500	-
Cl-6, Table-1(Length (mm) (Absorbent Core Only))	-	500	-
Cl-6, Table-1(Width (mm) (Absorbent Core Only))	-	500	-
Cl-7(WASHING, DRYING AND HANDLING INSTRUCTION)	-	500	-
Cl-8, Table-2 (i) (a)("Colour fastness to rubbing: Dry ")	-	2000	Color fastness to rubbing (Dry)- Rs 2000/-
Cl-8, Table-2 (i) (b)(Colour fastness to rubbing: Wet)	-	2000	Color fastness to rubbing (Wet)- Rs 2000/-
Cl-8, Table-2 (ii) (a)("Colour fastness to perspiration (acidic and alkaline): Colour change ")	-	1500	Color fastness to perspiration (for acidic cycle)- Rs 1500/-
Cl-8, Table-2 (ii) (b)(Colour fastness to perspiration (acidic and alkaline): Staining)	-	1500	Color fastness to perspiration (for alkaline cycle)- Rs 1500/-
Cl-8, Table-2 (iii) (a)(Colour fastness to washing: Colour change)	-	1500	Color fastness to Washing (for color change cycle)- Rs 1500/-
Cl-8, Table-2 (iii) (b)(Colour fastness to washing: Staining)	-	1500	Color fastness to Washing (for staining cycle)- Rs 1500/-
Cl-8, Table-2 (iv)("Dimensional stability to washing, percentage, Max Length and width")	-	1500	-
Cl-9.1(pH Value)	-	1000	-
Cl-9.2(Ability to Withstand Pressure after Absorption)	-	1500	-
Cl-9.3(Hygiene Testing Requirement)	-	8500	Clause 9.3 (Include 9.3.1 & 9.3.2)- Total-8500
Cl-9.3.1(Bacterial and Fungal Bioburden)	-	5500	-
Cl-9.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus)	-	3000	-
Cl-9.3.3(Good Manufacturing Practice Guideline for Hygiene Requirement)	-	500	-
Cl-9.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization)	-	0	clause 9.4 is in exclusion
Cl-9.5(Phthalate Test)	-	6000	-
Cl-12(Marking)	-	500	-
Cl-3.1(Material- cover or the top sheet)	-	0	-
Cl-3.2(Material- absorbent core;)	-	0	-
Cl-3.3(Material- bottom layer.)	-	0	-
Cl-4(MANUFACTURE, WORKMANSHIP AND FINISH)	-	0	-
Cl-5(FASTENING MECHANISM)	-	0	-
Cl-6, Table-1(Length (mm) (Absorbent Core Only))	-	0	-
Cl-6, Table-1(Width (mm) (Absorbent Core Only))	-	0	-
Cl-7(WASHING, DRYING AND HANDLING INSTRUCTION)	-	0	-
Cl-8, Table-2 (i) (a)("Colour fastness to rubbing: Dry ")	-	0	-
Cl-8, Table-2 (i) (b)(Colour fastness to rubbing: Wet)	-	0	-
Cl-8, Table-2 (ii) (a)("Colour fastness to perspiration (acidic and alkaline): Colour change ")	-	0	-
Cl-8, Table-2 (ii) (b)(Colour fastness to perspiration (acidic and alkaline): Staining)	-	0	-
Cl-8, Table-2 (iii) (a)(Colour fastness to washing: Colour change)	-	0	-
Cl-8, Table-2 (iii) (b)(Colour fastness to washing: Staining)	-	0	-
Cl-8, Table-2 (iv)("Dimensional stability to washing, percentage, Max Length and width")	-	0	-
Cl-9.1(pH Value)	-	0	-
Cl-9.2(Ability to Withstand Pressure after Absorption)	-	0	-
Cl-9.3(Hygiene Testing Requirement)	-	0	-
Cl-9.3.1(Bacterial and Fungal Bioburden)	-	0	-
Cl-9.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus)	-	0	-
Cl-9.3.3(Good Manufacturing Practice Guideline for Hygiene Requirement)	-	0	-
Cl-9.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization)	-	0	-
Cl-9.5(Phthalate Test)	-	0	-
Cl-12(Marking)	-	0	-
Cl-3.1(Material- cover or the top sheet)	-	-	-
Cl-3.2(Material- absorbent core;)	-	-	-
Cl-3.3(Material- bottom layer.)	-	-	-
Cl-4(MANUFACTURE, WORKMANSHIP AND FINISH)	-	-	-
Cl-5(FASTENING MECHANISM)	-	-	-
Cl-6, Table-1(Length (mm) (Absorbent Core Only))	-	-	-
Cl-6, Table-1(Width (mm) (Absorbent Core Only))	-	-	-
Cl-7(WASHING, DRYING AND HANDLING INSTRUCTION)	-	-	-
Cl-8, Table-2 (i) (a)("Colour fastness to rubbing: Dry ")	-	-	-
Cl-8, Table-2 (i) (b)(Colour fastness to rubbing: Wet)	-	-	-
Cl-8, Table-2 (ii) (a)("Colour fastness to perspiration (acidic and alkaline): Colour change ")	-	-	-
Cl-8, Table-2 (ii) (b)(Colour fastness to perspiration (acidic and alkaline): Staining)	-	-	-
Cl-8, Table-2 (iii) (a)(Colour fastness to washing: Colour change)	-	-	-
Cl-8, Table-2 (iii) (b)(Colour fastness to washing: Staining)	-	-	-
Cl-8, Table-2 (iv)("Dimensional stability to washing, percentage, Max Length and width")	-	-	-
Cl-9.1(pH Value)	-	-	-
Cl-9.2(Ability to Withstand Pressure after Absorption)	-	-	-
Cl-9.3(Hygiene Testing Requirement)	-	-	-
Cl-9.3.1(Bacterial and Fungal Bioburden)	-	-	-
Cl-9.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus)	-	-	-
Cl-9.3.3(Good Manufacturing Practice Guideline for Hygiene Requirement)	-	-	-
Cl-9.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization)	-	-	-
Cl-9.5(Phthalate Test)	-	-	-
Cl-10(Anti-bacterial activity value)	-	-	-
Cl-12(Marking)	-	-	-

25 Feb, 2027

-
Included w.e.f 18.11.2025 "Cl-9.4 (Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization)

IS 18755 (2024)

Tri-ply SS-AL-SS material used for manufacture of utensils and kitchen appliances Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material and designation)	-	500	-
Cl-5(Manufacturer)	-	500	-
Cl-6(Aluminium for use as matrix)	-	3500	For complete 6.0 clause- Rs 3500/-
Cl-6(Top-surface of the aluminium matrix)	-	0	For complete 6.0 clause- Rs 3500/-
Cl-6(Bottom-surface of the aluminium matrix)	-	0	For complete 6.0 clause- Rs 3500/-
Cl-7.1.1(Tensile properties)	-	4500	For complete 7.1 clause- Rs 4500/-
Cl-7.1.1(Apparent Yield Strength)	-	0	For complete 7.1 clause- Rs 4500/-
Cl-7.1.1(Tensile Strength Mpa,)	-	0	For complete 7.1 clause- Rs 4500/-
Cl-7.1.2(Test Specimen)	-	0	For complete 7.1 clause- Rs 4500/-
Cl-7.1.3(Test Parameters)	-	0	For complete 7.1 clause- Rs 4500/-
Cl-7.2.1(Bond strength of Tri-Ply)	-	5000	For complete 7.2 clause- Rs 5000/-
Cl-7.2.2(Sample Preparation and Test Specimen)	-	0	For complete 7.2 clause- Rs 5000/-
Cl-7.2.3(Test Apparatus)	-	0	For complete 7.2 clause- Rs 5000/-
Cl-7.2.4(Procedure)	-	0	For complete 7.2 clause- Rs 5000/-
Cl-8.1(Sample of suitable size)	-	6500	For complete 8.0 clause- Rs 6500/-
Cl-8.2(specimen for peel strength)	-	0	For complete 8.0 clause- Rs 6500/-
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS304 and Al 19500 interface)	-	0	For complete 8.0 clause- Rs 6500/-
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS430 and Al 19500 interface)	-	0	For complete 8.0 clause- Rs 6500/-
Cl-9.1(Thickness)	-	1500	-
Cl-9.2(Diameter)	-	1500	-
Cl-9.3(Flatness)	-	1500	-
Cl-10(surface finish)	-	1500	-
Cl-11(Workmanship, finish and appearance)	-	1500	-
Cl-14(Marking)	-	500	-

25 Feb, 2027

-
included w.e.f 26.11.2025

IS 16014 (2024)

MECHANICALLY WOVEN DOUBLE-TWISTED HEXAGONAL WIRE MESH GABIONS REVET MATTRESSES ROCK FALL NETTING AND OTHER PRODUCTS FOR CIVIL ENGINEERING PURPOSES GALVANIZED STEEL WIRE OR GALVANIZED STEEL WIRE WITH POLYMER COATING SPECIFICATION ( Second Revision )

ALL

388000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Material and Manufacture)	-	1000	-
Cl-5.1.1(Class 1 double-twisted mesh)	-	1500	-
Cl-5.1.2(Class 2 double-twisted mesh)	-	1500	-
Cl-5.4.1(Galvanized Rings)	-	1000	-
Cl-5.4.2(Stainless Steel Fasteners)	-	2500	-
Cl-6.1(Tensile Strength)	-	2500	-
Cl-6.2, Table-7 (i)(Mesh wire dia, mm)	-	500	-
Cl-6.2, Table-7 (ii)(Tensile Strength Parallel to twist, kN/m)	-	3500	-
Cl-5.3(Lacing wire and stiffeners)	-	2500	-
Cl-7.1.1(Mass of Zinc/Zinc Alloy Coating)	-	1500	-
Cl-7.1.2(Adhesion of Zinc/Zinc Alloy Coating)	-	1500	-
Cl-7.1.3(Ageing and Corrosion Resistance)	-	95000	-
Cl-7.2 (a)(Specific gravity)	-	500	-
Cl-7.2 (b)(Tensile strength)	-	2500	-
Cl-7.2 (c)(Hardness)	-	1000	-
Cl-7.2 (d)(Resistance of polymer coating to sodium chloride solution)	-	5500	-
Cl-7.2 (e)(Salt spray exposure)	-	90000	-
Cl-7.2 (f)(Modulus of Elasticity)	-	2500	-
Cl-7.2 (g)(Brittleness Temperature)	-	5500	-
Cl-7.2 (h)(Resistance to UV rays)	-	195000	-
Cl-8.12(Mesh Opening Tolerances)	-	1000	-
Cl-9(Workmanship)	-	500	-
Cl-12.1(Tensile Strength of Wire Mesh Panel)	-	2500	-
Cl-12.2(Punch Test)	-	5500	-
Cl-12.3(Pull-Apart Resistance Test/Selvedge Strength Test/Panel to Panel Connection)	-	5000	-
Cl-12.4(Metallic Coating Mass)	-	1500	-
Cl-12.5(Polymer Coating Thickness)	-	1000	-
Cl-12.6(Polymer Coating)	-	0	Already filled in clause 7.2 (d)
Cl-12.7.1(Abrasion Resistance Test)	-	3500	-
Cl-12.7.2(Corrosion Spread Test)	-	50000	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (i)(Mesh wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (ii)(Edge/Selvedge wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iii)(Lacing wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iv)(Polymer coating thickness,mm)	-	0	Already filled in cl. 12.5
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (v)(Typical sizes Length ×Width × Height(m))	-	500	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (vi)(Tolerances in size of Units)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (i)(Mesh wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (ii)(Edge/Selvedge wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iii)(Lacing wire dia, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iv)(Polymer coating thickness, mm)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (v)(Typical size Length × Width)	-	500	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (vi)(Tolerances in size of netting rolls)	-	500	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (i)(Mesh wire dia,)	-	500	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (ii)(Tensile Strength Parallel to twist,)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iii)(Tensile Strength Perpendicular to twist, kN/m)	-	2500	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iv)(Selvedge Strength, kN/m)	-	2500	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (v)(Punch Strength, kN)	-	0	Already filled cl. 12.2
Cl-6.2, 11.2, 12.2 (b), Table-7 (vi)(Panel to panel connection(lacing wire/ fasteners), kN/m)	-	2500	-
Cl-13(Marking)	-	500	-
Cl-5(Material and Manufacture)	-	0	-
Cl-5.1.1(Class 1 double-twisted mesh)	-	0	-
Cl-5.1.2(Class 2 double-twisted mesh)	-	0	-
Cl-5.4.1(Galvanized Rings)	-	0	-
Cl-5.4.2(Stainless Steel Fasteners)	-	0	-
Cl-6.1(Tensile Strength)	-	0	-
Cl-6.2, Table-7 (i)(Mesh wire dia, mm)	-	0	-
Cl-6.2, Table-7 (ii)(Tensile Strength Parallel to twist, kN/m)	-	0	-
Cl-5.3(Lacing wire and stiffeners)	-	0	-
Cl-7.1.1(Mass of Zinc/Zinc Alloy Coating)	-	0	-
Cl-7.1.2(Adhesion of Zinc/Zinc Alloy Coating)	-	0	-
Cl-7.1.3(Ageing and Corrosion Resistance)	-	0	-
Cl-7.2 (a)(Specific gravity)	-	0	-
Cl-7.2 (b)(Tensile strength)	-	0	-
Cl-7.2 (c)(Hardness)	-	0	-
Cl-7.2 (d)(Resistance of polymer coating to sodium chloride solution)	-	0	-
Cl-7.2 (e)(Salt spray exposure)	-	0	-
Cl-7.2 (f)(Modulus of Elasticity)	-	0	-
Cl-7.2 (g)(Brittleness Temperature)	-	0	-
Cl-7.2 (h)(Resistance to UV rays)	-	0	-
Cl-8.12(Mesh Opening Tolerances)	-	0	-
Cl-9(Workmanship)	-	0	-
Cl-12.1(Tensile Strength of Wire Mesh Panel)	-	0	-
Cl-12.2(Punch Test)	-	0	-
Cl-12.3(Pull-Apart Resistance Test/Selvedge Strength Test/Panel to Panel Connection)	-	0	-
Cl-12.4(Metallic Coating Mass)	-	0	-
Cl-12.5(Polymer Coating Thickness)	-	0	-
Cl-12.6(Polymer Coating)	-	0	-
Cl-12.7.1(Abrasion Resistance Test)	-	0	-
Cl-12.7.2(Corrosion Spread Test)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (i)(Mesh wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (ii)(Edge/Selvedge wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iii)(Lacing wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iv)(Polymer coating thickness,mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (v)(Typical sizes Length ×Width × Height(m))	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (vi)(Tolerances in size of Units)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (i)(Mesh wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (ii)(Edge/Selvedge wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iii)(Lacing wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iv)(Polymer coating thickness, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (v)(Typical size Length × Width)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (vi)(Tolerances in size of netting rolls)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (i)(Mesh wire dia,)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (ii)(Tensile Strength Parallel to twist,)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iii)(Tensile Strength Perpendicular to twist, kN/m)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iv)(Selvedge Strength, kN/m)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (v)(Punch Strength, kN)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (vi)(Panel to panel connection(lacing wire/ fasteners), kN/m)	-	0	-
Cl-13(Marking)	-	0	-
Cl-5(Material and Manufacture)	-	0	-
Cl-5.1.1(Class 1 double-twisted mesh)	-	0	-
Cl-5.1.2(Class 2 double-twisted mesh)	-	0	-
Cl-5.4.1(Galvanized Rings)	-	0	-
Cl-5.4.2(Stainless Steel Fasteners)	-	0	-
Cl-6.1(Tensile Strength)	-	0	-
Cl-6.2, Table-7 (i)(Mesh wire dia, mm)	-	0	-
Cl-6.2, Table-7 (ii)(Tensile Strength Parallel to twist, kN/m)	-	0	-
Cl-5.3(Lacing wire and stiffeners)	-	0	-
Cl-7.1.1(Mass of Zinc/Zinc Alloy Coating)	-	0	-
Cl-7.1.2(Adhesion of Zinc/Zinc Alloy Coating)	-	0	-
Cl-7.1.3(Ageing and Corrosion Resistance)	-	0	-
Cl-7.2 (a)(Specific gravity)	-	0	-
Cl-7.2 (b)(Tensile strength)	-	0	-
Cl-7.2 (c)(Hardness)	-	0	-
Cl-7.2 (d)(Resistance of polymer coating to sodium chloride solution)	-	0	-
Cl-7.2 (e)(Salt spray exposure)	-	0	-
Cl-7.2 (f)(Modulus of Elasticity)	-	0	-
Cl-7.2 (g)(Brittleness Temperature)	-	0	-
Cl-7.2 (h)(Resistance to UV rays)	-	0	-
Cl-8.12(Mesh Opening Tolerances)	-	0	-
Cl-9(Workmanship)	-	0	-
Cl-12.1(Tensile Strength of Wire Mesh Panel)	-	0	-
Cl-12.2(Punch Test)	-	0	-
Cl-12.3(Pull-Apart Resistance Test/Selvedge Strength Test/Panel to Panel Connection)	-	0	-
Cl-12.4(Metallic Coating Mass)	-	0	-
Cl-12.5(Polymer Coating Thickness)	-	0	-
Cl-12.6(Polymer Coating)	-	0	-
Cl-12.7.1(Abrasion Resistance Test)	-	0	-
Cl-12.7.2(Corrosion Spread Test)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (i)(Mesh wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (ii)(Edge/Selvedge wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iii)(Lacing wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iv)(Polymer coating thickness,mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (v)(Typical sizes Length ×Width × Height(m))	-	0	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (vi)(Tolerances in size of Units)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (i)(Mesh wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (ii)(Edge/Selvedge wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iii)(Lacing wire dia, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (iv)(Polymer coating thickness, mm)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (v)(Typical size Length × Width)	-	0	-
Cl-5.5, 8.1, 8.2, 8.11, Table-6 (vi)(Tolerances in size of netting rolls)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (i)(Mesh wire dia,)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (ii)(Tensile Strength Parallel to twist,)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iii)(Tensile Strength Perpendicular to twist, kN/m)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (iv)(Selvedge Strength, kN/m)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (v)(Punch Strength, kN)	-	0	-
Cl-6.2, 11.2, 12.2 (b), Table-7 (vi)(Panel to panel connection(lacing wire/ fasteners), kN/m)	-	0	-
Cl-13(Marking)	-	0	-

25 Feb, 2027

-
Included w.e.f 23.07.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Atmy Analytical Labs Pvt. Ltd., Faridabad

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List