BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 nthsal-wb@nic.in

Scope List

Reset

64 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	1200	-
6(Interchangeability)	-	1200	-
7(Protection against accidental contact with live parts)	-	1200	-
8(Insulation Resistance and Electric Strength)	-	5000	-
9(MECHANICAL STRENGTH)	-	1200	-
10(cap temperature)	-	2000	-
11(Resistance to Heat)	-	2000	-
12(Resistance to Flame and Ignition)	-	5000	-
13(Fault conditions)	-	2000	-
14(Creepage distance and clearances)	-	1200	-
4(General requirement and General test requirements)	-	0	-
8(Strength after humidity treatment)	-	5000	-
5(Marking)	-	1200	-
6(Interchangeability)	-	1200	-
7(Protection against accidental contact with live parts)	-	1200	-
9(Mechanical strength)	-	1200	-
10(Cap temperature rise)	-	2000	-
11(Resistance to heat)	-	2000	-
12(Resistance to flame and ignition)	-	5000	-
13(Fault conditions)	-	2000	-
14(Creepage distances and clearances)	-	1200	-
15(Selection of lamps for tests (Sampling))	-	0	-
16(Condition of compliance)	-	0	-
17(Tests)	-	0	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	0	-
Annex B(Lamps with operating position limitations)	-	0	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	0	-

14 Jun, 2027

-
Included w.e.f. 05.08.2025

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-
(Cl.4.24) (Annex-P)(UV Radiations for metal halide lamps)	-	0	-
4.26.2(Short Circuit Protection)	-	0	-

14 Jun, 2027

-
Included w.e.f. 04.08.2025

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	500	NA
8(Terminals)	-	500	NA
9(PROVISION FOR EARTHING)	-	1000	NA
10(Protection against accidental contact with live parts)	-	500	NA
11(Mositure Resistance and Insulation)	-	3500	NA
12(Electric Strength)	-	1500	NA
13(Fault conditions)	-	1500	NA
15(Construction)	-	500	NA
16(Creepage distance and clearances)	-	500	NA
17(Screws, current carrying parts and connections)	-	1000	NA
18(Resistance to heat, fire and tracking)	-	12000	NA
19(Resistance to corrosion)	-	2000	NA

14 Jun, 2027

-
-

IS 16103 : Part 2 (2012)

Led modules for general lighting: Part 2 performance requirements

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Dimensions)	-	500	NA
7(Module Power)	-	2000	NA
8(Light Output)	-	5000	NA
9(Chromaticity Coordinates, Correlated colour temperature and colour rendering)	-	5000	NA
10(LED Module Life)	-	45000	NA
12(Information for Luminaire design)	-	500	NA

14 Jun, 2027

-
-

IS 16104 (2012)

D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification)	-	500	NA
6(Marking)	-	500	NA
7.2(Output voltage and Current)	-	1000	NA
7.3(Capacitive Load Requirement)	-	500	NA
7.4(Voltage surge during switching and operation)	-	1500	NA
8(Total Circuit Power)	-	2000	NA
9(Circuit Power Factor)	-	1000	NA
10(Supply Current)	-	1000	NA
12(Operational test for abnormal conditions)	-	2000	NA
13(Endurance)	-	20000	NA

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 4 (1987)

Specification for luminaires: Part 5 particular requirements: Sec 4 portable general purpose luminaires

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	500	Individual test charge 1200/- per sample for this tests.
6(Construction)	-	1000	Individual test charge 1200/- per sample for this tests.
7(Creepage Distance And Clearances)	-	1000	Individual test charge 1200/- per sample for this tests.
8(Provision for Earthing)	-	1000	Individual test charge 1200/- per sample for this tests.
9(Terminals)	-	1000	Individual test charge 1200/- per sample for this tests.
10(External & Internal Wiring)	-	500	Individual test charge 1200/- per sample for this tests.
11(Protection Against Electric Shock )	-	1000	Individual test charge 1200/- per sample for this tests.
13.3(Mechanical Strength Test )	-	1000	Individual test charge 1200/- per sample for this tests.
13.4(Endurance Test and Thermal test)	-	5000	Individual test charge 5500/- per sample for this tests.
13.5(Resistance To Dust & Moisture)	-	7500	Individual test charge 12000/- per sample for this tests.
13.6(Insulation Resistance and Electric Strength)	-	3000	Individual test charge 5000/- per sample for this tests.
13.7(Resistance to Heat, Fire & Tracking)	-	7500	Individual test charge 12000/- per sample for this tests.
13.8(Photometric Test)	-	10000	NA

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 7 (2017)

Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.4(General Test Requireements)	-	500	Individual test charge 1200/- per sample for this tests.
20.5(Classification of Luminaires')	-	500	Individual test charge 1200/- per sample for this tests.
20.6(Marking)	-	500	Individual test charge 1200/- per sample for this tests.
20.7(Construction)	-	1000	Individual test charge 1200/- per sample for this tests.
20.8(Creepage Distance and Clearances)	-	1000	Individual test charge 1200/- per sample for this tests.
20.9(Provision for earthing)	-	1000	Individual test charge 1200/- per sample for this tests.
20.10(Terminals)	-	1000	Individual test charge 1200/- per sample for this tests.
20.11(External & Internal Wiring)	-	500	Individual test charge 1200/- per sample for this tests.
20.12(Protection against electric shock)	-	1000	Individual test charge 1200/- per sample for this tests.
20.13(Endurance Tests and Thermal Tests)	-	5000	Individual test charge 5500/- per sample for this tests.
20.14(Resistance to Dust & Moisture)	-	7500	Individual test charge 12000/- per sample for this tests.
20.15(Insulation Resistance and Electric Strength)	-	3000	Individual test charge 5000/- per sample for this tests.
20.16(Resistance to Heat , fire and tracking)	-	7500	Individual test charge 12000/- per sample for this tests.

14 Jun, 2027

-
-

IS 10322 : PART 5 : SEC 3 (2012)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 5 (2013)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 6 (2013)

Luminaires: Part 5 particular requirements: Sec 6 handlamps

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-

14 Jun, 2027

-
-

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1, 5.2(Chemical Composition - Carbon)	-	500	-
5, 5.1, 5.2(Chemical Composition - Sulphur)	-	500	-
5, 5.1, 5.2(Chemical Composition - Phosphorus)	-	500	-
5, 5.1, 5.2(Chemical Composition - Manganese)	-	500	-
5, 5.1, 5.2(Chemical Composition - Silicon)	-	500	-
5, 5.1, 5.2(Chemical Composition - Nickel)	-	500	-
5, 5.1, 5.2(Copper)	-	500	-
5, 5.1, 5.2(Chromium)	-	500	-
Cl 6(Workmanship)	-	2000	-
7(Diameter & Out Of Round)	-	500	-
Cl 8(Decarburization)	-	2000	-
Cl 9(Inclusion)	-	4000	-
Cl 11(Size)	-	3000	-
Cl 10(Hardenability)	-	8000	-

14 Jun, 2027

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Ti)	-	500	-
6.1(V)	-	500	-
6.1(Mo)	-	500	-
6.1(Ni)	-	500	-
6.1(Cr)	-	500	-
10.1 (a)(Macro-examination)	-	1000	-
10.1 (b)(Sulphur print)	-	3000	-
Cl. 10.2(Bend)	-	500	-
Cl. 10.3(Camber)	-	500	-
Cl 11(Length, Width & Thickness)	-	500	-

14 Jun, 2027

-
-

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	1500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	1000	-
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	2000	-
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	500	-
Cl. 15.2, Table 3(Elongation- IS 1608)	-	500	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	500	-
Cl. 10.1, 14.1, 18.1(Straightness)	-	500	-

14 Jun, 2027

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

Fe 415 to Fe 700, size 8mm-40mm

29500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 9.4(Rebend Test)	-	1000	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 7.2 Table -2 (Nominal Mass)	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Clause 8.1(Table 3)(Total Elongation at Maximum Force)	-	1000	-
Cl. 4.3(Visual Inspection.)	-	1000	-
4.1(Carbon %)	-	1416	Inclusive of GST@18%
4.1(Sulphur %)	-	1416	Inclusive of GST@18%
4.1(Phosphorus %)	-	1416	Inclusive of GST@18%
4.1(Manganese %)	-	1416	Inclusive of GST@18%
4.1(Silicon %)	-	1416	Inclusive of GST@18%
4.1( Nitrogen%)	-	2360	Inclusive of GST@18%
4.1(CE)	-	2360	Inclusive of GST@18%
5.7(PullOut (Bond Test))	-	15000.00	Fee is dependent on size and exclusive of GST. Up to 12mm - Rs 10000.00 +GST Above 12mm - Rs 15000.00 +GST
Cl. 8.1 Table 3(TS/YS ratio)	-	1000	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	500	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	-

14 Jun, 2027

-
-

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

All Grade

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	1000	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
10(Tensile test)	-	3000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	0	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	0	-

14 Jun, 2027

-
-

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

GP TO GP 550

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	4000	-
Cl 8.2(Press)	-	1000	-
Cl 12(Workmanship)	-	1000	-
Cl 13(Weight)	-	1000	-
Cl 14(Length, Width & Thickness)	-	1000	-
Cl 10(Galvanising Test)	-	2000	-
Cl. 5.1(Carbon)	-	500	-
Cl. 5.1(Sulphur)	-	500	-
Cl. 5.1(Phosphorous)	-	500	-
Cl. 5.1(Manganese)	-	500	-
Cl. 5.1(Silicon)	-	500	-
Cl. 5.1(Titanium)	-	500	-
Cl-5.1(Aluminium)	-	500	-
Cl. 5.1(Copper)	-	500	-
Cl. 5.1(Vanadium)	-	500	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Depth of Corrugation))	-	250	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Pitch of Corrugation))	-	250	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Number of Corrugation))	-	0	-

14 Jun, 2027

-
-

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	1000	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	-
8.2(Mechanical Properties (as per IS 1717))	-	1000	-
8.3(Mechanical Properties (as per IS 1755))	-	1000	-
9.1(Galvanizing Requirements )	-	2000	-
9.2(Galvanizing Requirements )	-	1000	-
9.3(Galvanizing Requirements )	-	1000	-
11(Freedom from defects)	-	1000	-
6.2(Sulphur %)	-	500	-
6.2(Phosphorus %)	-	500	-
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	3000	-

14 Jun, 2027

-
-

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6.1, 6.2, Table 1(Nominal Dia of Mesh wire)	-	1000	-
Cl.6.1, 6.2, Table 1(Mesh Size)	-	1000	-
Cl.6.3, Table 1(Width of the fabric)	-	1000	-
Cl.6.3, Table 1(Length of the fabric)	-	1000	-
Cl.9.1.1(Tensile test of mesh and line wires- IS 1608)	-	2000	-
Cl.9.1.2(Wrapping test of mesh and line wires-IS 1755)	-	1000	-
Cl.9.1.3(Twist test of mesh and line wires-IS 1717)	-	1000	-
Cl.9.1.4(Bend test of mesh and line wires- IS 1608)	-	1000	-
Cl.9.2(Line wire (Mass of zinc coating)- IS 6745)	-	2000	-
Cl.9.2(Line Wire (Uniformity of Zinc coating)-IS 2633)	-	1000	-
Cl.9.2(Mesh wire (Mass of zinc coating)- IS 6745)	-	2000	-
Cl.9.2(Mesh Wire (Uniformity of Zinc coating)-IS 2633)	-	1000	-
Cl.5(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-

14 Jun, 2027

-
-

IS 738 (1994)

Wrought aluminium alloys, drawn tube for general engineering purposes - Specification (Third Revision)

All Grade

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7, IS 2678(Wall Thickness at any point)	-	500	-
Cl.7, IS 2678(Mean Wall Thickness)	-	500	-
Cl. 9.1 Table 2(Tensile Strength- IS 2657)	-	2000	-
Cl. 9.1 Table 2(0.2 percent proof stress- IS 2657)	-	2000	-
Cl. 9.1 Table 2(Elongation on guage length of 50 mm)	-	1000	-
Cl. 6(Freedom from Defects- Cl.6)	-	1000	-
Cl. 8.1, Table 1(Aluminium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Copper- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Magnesium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Silicon- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Iron- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Manganese- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Zinc- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Titanium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Chromium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-

14 Jun, 2027

-
-

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

All Grade as per Specification

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimension - IS 3965)	-	1000	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	2000	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	2000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	1000	-
Cl. 4(Freedom from Defects)	-	1000	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	1000	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	1000	-

14 Jun, 2027

-
-

IS 14543 (2024)

Packaged Drinking Water Other than Packaged Natural Mineral Water Specification Third Revision

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.3, Table-1 (i)(Colour, true colour units, Max)	-	150	-
Cl-5.3, Table-1 (ii)(Odour)	-	100	-
Cl-5.3, Table-1 (iii)(Taste)	-	100	-
Cl-5.3, Table-1 (iv)(Turbidity, nephelometric turbidity unit (NTU), Max)	-	150	-
Cl-5.3, Table-1 (v)(Total dissolved solids, mg/l, Max)	-	150	-
Cl-5.3, Table-1 (vi)(pH)	-	150	-
Cl-5.3, Table-2 (i)(Barium (as Ba))	-	275	-
Cl-5.3, Table-2 (ii)(Copper (as Cu))	-	275	-
Cl-5.3, Table-2 (iii)(Iron (as Fe))	-	275	-
Cl-5.3, Table-2 (iv)(Manganese (as Mn))	-	275	-
Cl-5.3, Table-2 (v)(Nitrate (as NO3 ))	-	300	-
Cl-5.3, Table-2 (vi)(Nitrite (as NO2 ))	-	300	-
Cl-5.3, Table-2 (vii)(Fluoride (as F))	-	300	-
Cl-5.3, Table-2 (viii)(Zinc (as Zn))	-	275	-
Cl-5.3, Table-2 (ix)(Silver (as Ag))	-	275	-
Cl-5.3, Table-2 (x)(Aluminium (as A1))	-	275	-
Cl-5.3, Table-2 (xi)(Chloride (as Cl))	-	150	-
Cl-5.3, Table-2 (xii)(Selenium (as Se))	-	275	-
Cl-5.3, Table-2 (xiii)(Sulphate (as SO4 ))	-	275	-
Cl-5.3, Table-2 (xiv)(Alkalinity (as HCO3 ))	-	150	-
Cl-5.3, Table-2 (xv)(Calcium (as Ca))	-	150	-
Cl-5.3, Table-2 (xvi)(Magnesium (as Mg))	-	150	-
Cl-5.3, Table-2 (xvii)(Sodium (as Na))	-	275	-
Cl-5.3, Table-2 (xviii)(Residual free chlorine)	-	300	-
Cl-5.3, Table-2 (xix)(Phenolic compounds (as C6H5OH))	-	300	-
Cl-5.3, Table-2 (xx)(Mineral oil)	-	300	-
Cl-5.3, Table-2 (xxi)(Anionic surface active agents)	-	300	-
Cl-5.3, Table-2 (xxii)(Sulphide)	-	300	-
Cl-5.3, Table-2 (xxiii)(Antimony (as Sb))	-	275	-
Cl-5.3, Table-2 (xxiv)(Borates (as B))	-	275	-
Cl-5.3, Table-2 (xxv)(Bromates (as BrO3 ))	-	500	-
Cl-5.3, Table-3 (i)(Mercury (as Hg))	-	300	-
Cl-5.3, Table-3 (ii)(Cadmium (as Cd))	-	300	-
Cl-5.3, Table-3 (iii)(Arsenic (as As))	-	300	-
Cl-5.3, Table-3 (iv)(Cyanide (as CN))	-	500	-
Cl-5.3, Table-3 (v)(Lead (as Pb))	-	300	-
Cl-5.3, Table-3 (vi)(Chromium (as Cr))	-	300	-
Cl-5.3, Table-3 (vii)(Nickel (as Ni))	-	300	-
Cl-5.3, Table-3 (viii)(Polychlorinated biphenyl (PCB))	-	500	-
Cl-5.3, Table-3 (ix)(Polynuclear aromatic hydrocarbons)	-	500	-
5.4/Annex D/i(P,P-DDT)	-	150	-
5.4/Annex D/ii(Lindane)	-	150	-
5.4/Annex D/iv(b-Endosulfan)	-	150	-
5.4/Annex D/xvi(Dieldrin)	-	150	-
5.4/Annex D/xvi(Aldrin)	-	150	-
5.4/Annex D/i(O,P-DDT)	-	150	-
5.4/Annex D/iv(a-Endosulfan)	-	150	-
5.4/Annex D/iii(d-HCH)	-	150	-
5.4/Annex D/i(O,P-DDD)	-	150	-
5.4/Annex D/i(P,P-DDE)	-	150	-
5.4/Annex D/i(O,P-DDE)	-	150	-
5.4/Annex D/iii(a-HCH)	-	150	-
5.4/Annex D/iii(β- HCH)	-	150	-
5.4/Annex D/iv(Endosulfan sulfate)	-	150	-
5.4/Annex D/i(P,P-DDD)	-	150	-
5.4/Annex D/xii(Alachlor)	-	150	-
5.4/Annex D/vii(Chlorpyrifos)	-	150	-
5.4/Annex D/x(Butachlor)	-	150	-
5.4/Annex D/vi(Ethion)	-	150	-
5.4/Annex D/xiv(Methyl parathion)	-	150	-
5.4/Annex D/xv(Malathion)	-	150	-
5.4/Annex D/viii(Phorate)	-	150	-
5.4/Annex D/v(Monochrotophos)	-	150	-
5.4/Annex D/xiii(Atrazine)	-	150	-
5.4/Annex D/viii(Phorate sulphoxide)	-	150	-
5.4/Annex D/viii(Phorate sulfone)	-	150	-
5.4/Annex D/xxvii(Methyl paraoxon)	-	150	-
5.4/Annex D/xxviii(Malaoxon)	-	150	-
5.4/Annex D/xi(Isoproturon)	-	150	-
5.4/Annex D/ix(2,4 –D)	-	150	-
Cl-5.2.1(Escherichia coli or thermotolerant bacteria)	-	400	-
Cl-5.2.2(Coliform)	-	400	-
Cl-5.2.3(Staphylococcus aureus)	-	400	-
Cl-5.2.4(Sulphite Reducing Anaerobes)	-	400	-
Cl-5.2.5(Pseudomonas Aeruginosa)	-	400	-
5.2.6(Aerobic Microbial Count @ 20 to 22 deg C)	-	0	-
Cl-5.2.7(Yeast and mould)	-	400	-
Cl-5.2.8(Salmonella)	-	400	-
Cl-5.2.9(Vibrio cholera)	-	400	-
Cl-5.4 (i)(Pesticide residues considered individually)	-	250	-
Cl-5.4 (ii)(Total pesticide residue)	-	250	-
5.3(Appearance)	-	100	-
Cl-5.2.3(Faecal streptococci)	-	400	-
Cl-5.2.8(shigella)	-	400	-
Cl-5.2.9(V.parahaemolyticus)	-	400	-
Cl-5.1(General Requirements)	-	200	-
Cl-5.2.6(Aerobic Microbial Count @ 37 deg C)	-	400	-

14 Jun, 2027

-
Exclusion: Cl-5.3, Table-4 (i) (Alpha emitters, Becquerel (Bq/l)), Cl-5.3, Table-4 (ii) (Beta emitters, Becquerel (Bq/l),) Cl-5.3, Table-3 (x) (Uranium)

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

32500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
7.1.1(Diameter of Core Wire)	-	500	-
7.1.2(Length of Electrodes)	-	500	-
7.2.1(Contact End)	-	500	-
7.2.2(Arc striking End)	-	500	-
7.3(Concentricity of Flux covering with core wire)	-	1500	-
7.4(Defects of Core wire and Coverings)	-	500	-
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	1000	-
9.1.2 Table 6 ( Yield Stress -Annex F)	-	1000	-
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	1000	-
9.1.3 Table 6 ( Impact Strength-Annex F)	-	4000	-
9.2(Butt Weld Bend Test-IS 1599)	-	8000	-
9.3(Running PerformanceTest-Annex H)	-	2000	-
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	-
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	-
9.6(Radiographic Test- IS 1182)	-	1000	-

14 Jun, 2027

-
-

IS 10702 (2023)

Hawai Chappal-Specification

31000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	2000	-
4.2(Length)	-	500	-
4.3(Thickness)	-	500	-
4.4 , Table No. 1 , i)(Density)	-	1000	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	0	Facility Not Available
4.4 , Table No. 1 , iii)(3Split tear strength)	-	2000	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1000	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1000	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1000	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	2000	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	500	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	0	Facility Not Available
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	0	Facility Not Available
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	2000	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1000	-
Cl.No. 5.2(lead content)	-	500	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	500	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	2000	-
Clause 4.1 - 4.1.3(Material)	-	500	-
Clause 4.1 - 4.1.4(Material)	-	500	-
Clause 4.2(Material)	-	500	-
Clause 4.3 - 4.3.1(Thickness)	-	500	-
Clause 4.3 - 4.3.2(Thickness)	-	500	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1000	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	2000	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1000	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1000	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1000	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1000	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1000	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1000	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	500	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	0	Facility Not Available
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	0	Facility Not Available
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	1000	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	2000	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1000	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1000	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1000	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	2000	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2000	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1000	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1000	-
6(MARKING AND PACKING)	-	500	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	0	Facility Not Available
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	0	Facility Not Available
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	2000	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1000	-
4.1(Material)	-	2000	-
4.2(Length)	-	500	-
4.3(Thickness)	-	500	-
4.4 , Table No. 1 , i)(Density)	-	1000	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	2000	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1000	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1000	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1000	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	1000	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	2000	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1000	-
Cl.No. 5.2(lead content)	-	500	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	500	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	2000	-
Clause 4.1 - 4.1.3(Material)	-	500	-
Clause 4.1 - 4.1.4(Material)	-	500	-
Clause 4.2(Material)	-	500	-
Clause 4.3 - 4.3.1(Thickness)	-	500	-
Clause 4.3 - 4.3.2(Thickness)	-	500	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1000	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	2000	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1000	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1000	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1000	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1000	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1000	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	2000	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1000	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	2000	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	2000	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1000	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1000	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1000	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	2000	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2000	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	1000	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1000	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1000	-
6(MARKING AND PACKING)	-	500	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	1000	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1000	-

14 Jun, 2027

-
Included w.e.f 26.08.2025 For mechanical requirement only Excluding Cl 4.4 , Table No. 1 , ii) (2Compression set at constant stress), Cl 4.4 , Table No . 3 , i) (Toe post attachment strength), Cl 4.4 , Table No . 3 , ii) (Attachment strength of rear strap), Clause 4.4 Table 3 -i) ("Toe post attachment strength, N, Min"), Clause 4.4 Table 3 -ii) ("Attachment strength of rear strap, N, Min"), Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1) (Toe post attachment strength), Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1) (Attachment strength of rear strap), Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1) (Compression set at constant stress)

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

E 250 TO E 650 (Grade - A, B, C, BR & B0 )

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	2000	-
Clause 11.3(Bend Test)	-	1000	-
Clause 12(Impact Test)	-	4000	-
Clause 15, Table 4(Dimension)	-	1000	-
Cl 18(Weight)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	-

14 Jun, 2027

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	0	-
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	500	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii b(Expansion after aeration)	-	0	-
7 Table-3 iii a(Setting Time Initial)	-	250	-
7 Table-3 iii b(Setting Time Final)	-	250	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
6.1 Table-2 viii(Alkali content)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	500	-
Cl-8.1(Dimensions -length)	-	1000	-
Cl-8.2(Thickness of the plywood boards)	-	500	-
Cl-8.3(Squareness)	-	1000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	2000	-
Cl-11.3.2(Mycological Test)	-	1500	-
Cl-11.4(Moisture Content)	-	1000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	2000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	2000	-
Cl-5.1(Classification by appearance)	-	500	-
Cl-5.2, Table- 1 (i)(Blister)	-	250	-
Cl-5.2, Table- 1 (ii)(Checks)	-	250	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	250	-
Cl-5.2, Table- 1 (iv)(Dote)	-	250	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	250	-
Cl-5.2, Table- 1 (vi)(Joints)	-	250	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	250	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	250	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	250	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	250	-
Cl-5.2, Table- 1 (xi)(Patches)	-	250	-
Cl-5.2, Table- 1 (xii)(Splits)	-	250	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	250	-
Cl-7.2.1(Thickness of veneers)	-	500	-
Cl-7.2.3(Grain Direction)	-	500	-

14 Jun, 2027

-
Included w.e.f.10.12.2024 Exclusion Cl-11.6 (Formaldehyde Content Test) Cl-11.7 (Steady-State Formaldehyde Emission Test)

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

21750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	1000	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	1000	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	1000	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	1000	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	1000	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	2000	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	1000	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	1000	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	1000	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	1000	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	1000	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1000	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	1000	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	2000	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	7000	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	1000	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	2000	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1000	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	2000	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	2000	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	2000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	2000	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	2000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	2000	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	2000	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	1000	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	1000	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	1000	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	1000	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	1000	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	1000	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	1000	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	1000	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	1000	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	1000	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	1000	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	1000	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	1000	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	1000	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	1000	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	1000	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	-	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	-	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	-	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	-	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	-	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	-	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	-	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	-	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	-	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	-	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	-	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	-	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	-	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	-	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	-	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	-	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	-	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	-	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	-	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	-	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	-	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	-	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	-	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	-	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	-	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	-	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	-	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	-	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	-	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	-	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	-	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	-	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	-	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Dimensions)	-	500	-
7.1, Table -1(Average Wet Compressive Strength)	-	2000	-
7.4(Water Absorption)	-	1000	-
7.3(Efflorescence Test)	-	1000	-
3.1(General Requirements)	-	500	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	500	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	500	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	500	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	10000	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

IS 13801 (2013)

Chequered Cement Concrete Tiles -

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
Cl 12.1(Concavity & Convexity )	-	500	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	500	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.4(Water absorption)	-	1000	-
Cl 12.5(Wet transverse strength)	-	2000	-
Cl 12.6(Resistance to wear)	-	2500	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 nthsal-wb@nic.in

Scope List