BIS - LIMS (Laboratory Information Management System)

Softlines and Electrical Safety Testing Laboratory TUV Rheinland India Pvt Ltd., Gurgaon (8167106)

330-331 Udyog Vihar Phase IV, Gurugram, Gurugram, Haryana, 122015

9711918976 g.kaur@ind.tuv.com

Scope List

Reset

14 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1(REQUIREMENTS-General)	-	500	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	500	-
5.5 (Amendment 1)(Thickness)	-	500	-
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	500	-
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	500	-
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	2000	-
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	980	-
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	655	-
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	655	-
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	1000	-

19 Jan, 2027

-
amendment 1 included w.e.f.09.10.2024.

IS 13893 (1994)

Polyurethane soles semirigid - specification

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Design)	-	500	-
4.2 (Amendment 2)(Thickness)	-	500	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	500	-
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	500	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	1210	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	1500	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	3630	1.5 Lacs Cycle
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	655	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	655	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	655	-
5, 5.1, 5.2(Packing And Marking)	-	500	-

19 Jan, 2027

-
amendment included w.e.f 09.10.2024

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

45750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	525	-
Cl. No.5("SIZE AND FITTINGS ")	-	525	-
Cl. No.6("CONSTRUCTION ")	-	525	-
Cl. No.7(MATERIAL)	-	550	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	655	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	655	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1500	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	655	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1210	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1210	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	655	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	0.01	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	500	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	1210	-
Cl. No.8.4,Table no. 5(i)(Density)	-	500	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1210	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1500	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1210	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1030	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1030	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1030	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1030	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1030	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1030	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	3630	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1030	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1210	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	3990	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4200	4200 each (DD & CD)
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	3150	All Amines
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2100	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	2500	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	4200	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	3675	1575 -Free 2100 - Release
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	525	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	10500	10500 more than 5 analytes
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	5250	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	700	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	3780	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3150	-
Cl. No.8.6.2(Lead content)	-	1260	-
Cl. No.4(SHAPE AND DESIGN)	-	500	-
Cl. No.5("SIZE AND FITTINGS ")	-	500	-
Cl. No.6("CONSTRUCTION ")	-	1	-
Cl. No.7(MATERIAL)	-	1	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	1	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	1	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	1	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	1	-
Cl. No.8.4,Table no. 5(i)(Density)	-	1	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	1	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	11	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	700	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	700	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	700	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	4000	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2100	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	590	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	4000	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	2000	-
Cl. No.8.6.2(Lead content)	-	700	-
Cl. No.4(SHAPE AND DESIGN)	-	500	-
Cl-5 ((Amendment No-1)(Category And Type)	-	500	-
Cl. No.6("CONSTRUCTION ")	-	500	-
Cl. No.7(MATERIAL)	-	500	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	500	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	590	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	500	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	700	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	700	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	700	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	2000	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1050	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1050	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4000	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1050	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1050	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	1950	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1950	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	500	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	4500	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	2000	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1050	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	700	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	700	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	4000	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	700	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1050	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1050	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1050	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	700	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	500	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	500	-
Cl-10 (Amendment No-1)(Marking)	-	500	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	21000	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	500	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	500	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	4000	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	700	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1050	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1050	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	800	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1050	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1050	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	700	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	500	-
Cl. No.8.4,Table no. 5(i)(Density)	-	500	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1050	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1050	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	21000	-
Cl. No.9.(MARKING AND PACKING)	-	500	-
Cl. No.8.6.2(Lead content)	-	800	-
Cl. No.5("SIZE AND FITTINGS ")	-	500	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	500	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	500	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	500	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	500	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	500	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1020	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	900	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	800	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	500	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	800	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	500	-
Cl. No.4(SHAPE AND DESIGN)	-	1	-
Cl-5 ((Amendment No-1)(Category And Type)	-	1	-
Cl. No.6("CONSTRUCTION ")	-	1	-
Cl. No.7(MATERIAL)	-	1	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	1	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	1	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	1	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	1	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	1	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	1	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	1	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	1	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	1	-
Cl-10 (Amendment No-1)(Marking)	-	1	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	1	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	1	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	1	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	1	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	1	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	1	-
Cl. No.8.4,Table no. 5(i)(Density)	-	1	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	1	-
Cl. No.9.(MARKING AND PACKING)	-	1	-
Cl. No.8.6.2(Lead content)	-	1	-
Cl. No.5("SIZE AND FITTINGS ")	-	1	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	1	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl. No.4(SHAPE AND DESIGN)	-	1	-
Cl-5 ((Amendment No-1)(Category And Type)	-	1	-
Cl. No.6("CONSTRUCTION ")	-	1	-
Cl. No.7(MATERIAL)	-	1	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	1	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	1	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	1	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	1	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	1	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	11	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	1	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	1	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	1	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	1	-
Cl-10 (Amendment No-1)(Marking)	-	1	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	1	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	1	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	1	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	1	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	1	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	1	-
Cl. No.8.4,Table no. 5(i)(Density)	-	1	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	1	-
Cl. No.9.(MARKING AND PACKING)	-	1	-
Cl. No.8.6.2(Lead content)	-	1	-
Cl. No.5("SIZE AND FITTINGS ")	-	1	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	1	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl. No.4(SHAPE AND DESIGN)	-	1	-
Cl-5 ((Amendment No-1)(Category And Type)	-	1	-
Cl. No.6("CONSTRUCTION ")	-	1	-
Cl. No.7(MATERIAL)	-	1	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	1	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	1	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	1	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	1	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	1	1
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	1	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	1	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	1	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	1	-
Cl-10 (Amendment No-1)(Marking)	-	1	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	1	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	1	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	1	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	1	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	1	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	1	-
Cl. No.8.4,Table no. 5(i)(Density)	-	1	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	1	-
Cl. No.9.(MARKING AND PACKING)	-	1	-
Cl. No.8.6.2(Lead content)	-	1	-
Cl. No.5("SIZE AND FITTINGS ")	-	1	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	1	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl. No.4(SHAPE AND DESIGN)	-	1	-
Cl-5 ((Amendment No-1)(Category And Type)	-	1	-
Cl. No.6("CONSTRUCTION ")	-	1	-
Cl. No.7(MATERIAL)	-	1	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	1	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	1	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	1	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	1	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	1	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	1	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	1	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	1	-
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	1	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	1	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	1	-
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	1	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	1	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	1	-
Cl-10 (Amendment No-1)(Marking)	-	1	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	1	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	1	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	1	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	1	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	1	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	1	-
Cl. No.8.4,Table no. 5(i)(Density)	-	1	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	1	-
Cl. No.9.(MARKING AND PACKING)	-	1	-
Cl. No.8.6.2(Lead content)	-	1	-
Cl. No.5("SIZE AND FITTINGS ")	-	1	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	1	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	1	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	1	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	1	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	1	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	1	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	1	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	1	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	1	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	1	-

19 Jan, 2027

-
Included w.e.f 14.01.2025 Exclusion : Cl. No.8.4,Table no. 4(iii) (Abrasion resistance)

IS 10702 (2023)

Hawai Chappal-Specification

38905 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	550	-
4.2(Length)	-	525	-
4.3(Thickness)	-	525	-
4.4 , Table No. 1 , i)(Density)	-	500	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1000	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	655	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1500	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1210	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1500	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1500	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	500	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	655	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	525	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	525	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1030	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1030	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1210	-
6(MARKING AND PACKING)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4200	4200 each
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	3150	All Amines
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2100	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	2500	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	4200	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	3675	1575 - Free 2100 - Released
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	525	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	10500	More than 5 analytes
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	5250	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	700	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	3780	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3150	-
Cl.No. 5.2(lead content)	-	1260	-
4.1(Material)	-	550	-
4.2(Length)	-	525	-
4.3(Thickness)	-	525	-
4.4 , Table No. 1 , i)(Density)	-	500	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1000	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	655	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1500	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1210	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1500	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1500	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	500	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	655	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	525	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	525	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1030	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1030	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1210	-
6(MARKING AND PACKING)	-	500	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4200	Each (DD&CD)
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	3150	All Amines
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2100	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	2500	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	4200	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	3675	Free -1575 Release - 2100
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	525	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	10500	More Than 5 Analytes
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	5250	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	700	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	3780	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	3150	-
Cl.No. 5.2(lead content)	-	1260	-
4.1(Material)	-	1	-
4.2(Length)	-	1	-
4.3(Thickness)	-	1	-
4.4 , Table No. 1 , i)(Density)	-	1	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	1	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	0.99	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	1	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	1	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	1	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1	-
6(MARKING AND PACKING)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
Cl.No. 5.2(lead content)	-	1	-
4.1(Material)	-	1	-
4.2(Length)	-	1	-
4.3(Thickness)	-	1	-
4.4 , Table No. 1 , i)(Density)	-	1	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	1	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	1	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	1	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	1	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	1	-
6(MARKING AND PACKING)	-	1	-
Cl.No. 5.2(lead content)	-	1	-
Clause 4.1 - 4.1.1(Bottom Material)	-	1	-
Clause 4.1 - 4.1.2(Strap Material)	-	1	-
Clause 4.1 - 4.1.3(Material)	-	1	-
Clause 4.1 - 4.1.4(Material)	-	1	-
Clause 4.2(Material)	-	1	-
Clause 4.3 - 4.3.1(Thickness)	-	1	-
Clause 4.3 - 4.3.2(Thickness)	-	1	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	1	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	1	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	1	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	1	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	1	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	1	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	1	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	1	-
Cl-4 ((Amendment No-1)(Category And Type)	-	1	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	1	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	1	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	1	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	1	-
Cl-4.4, Table -1 S. No-1 (vii) (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (ii), (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	1	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	1	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
4.1(Material)	-	1	-
4.2(Length)	-	1	-
4.3(Thickness)	-	1	-
4.4 , Table No. 1 , i)(Density)	-	1	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	1	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	1	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	1	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	1	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	1	-
6(MARKING AND PACKING)	-	1	-
Cl.No. 5.2(lead content)	-	1	-
Clause 4.1 - 4.1.1(Bottom Material)	-	1	-
Clause 4.1 - 4.1.2(Strap Material)	-	1	-
Clause 4.1 - 4.1.3(Material)	-	1	-
Clause 4.1 - 4.1.4(Material)	-	1	-
Clause 4.2(Material)	-	1	-
Clause 4.3 - 4.3.1(Thickness)	-	1	-
Clause 4.3 - 4.3.2(Thickness)	-	1	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	1	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	1	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	1	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	1	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	1	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	1	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	1	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	1	-
Cl-4 ((Amendment No-1)(Category And Type)	-	1	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	1	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	1	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	1	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	1	-
Cl-4.4, Table -1 S. No-1 (vii) (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (ii), (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	1	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	1	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-
4.1(Material)	-	1	-
4.2(Length)	-	1	-
4.3(Thickness)	-	11	-
4.4 , Table No. 1 , i)(Density)	-	1	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	1	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	1	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	1	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	1	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	1	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	1	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	1	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	1	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	1	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	1	-
6(MARKING AND PACKING)	-	1	-
Cl.No. 5.2(lead content)	-	1	-
Clause 4.1 - 4.1.1(Bottom Material)	-	1	-
Clause 4.1 - 4.1.2(Strap Material)	-	1	-
Clause 4.1 - 4.1.3(Material)	-	1	-
Clause 4.1 - 4.1.4(Material)	-	1	-
Clause 4.2(Material)	-	1	-
Clause 4.3 - 4.3.1(Thickness)	-	1	-
Clause 4.3 - 4.3.2(Thickness)	-	1	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	1	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	1	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	1	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	1	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	1	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	1	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	1	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	1	-
Cl-4 ((Amendment No-1)(Category And Type)	-	1	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	1	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	1	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	1	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	1	-
Cl-4.4, Table -1 S. No-1 (vii) (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1	-
Cl-4.4, Table -2 S. No-1 (ii), (Amendment No-1)(Chemical requirements)	-	1	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	1	-
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	1	-
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	1	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	1	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1	-

19 Jan, 2027

-
Included w.e.f 14.01.2025

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	625	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	625	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	500	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	500	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	1000	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	420	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	625	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	625	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	500	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1200	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	500	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	1000	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	625	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	625	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	625	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	1500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	625	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	625	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	625	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	1200	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	1200	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	500	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	1650	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	1650	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	500	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	500	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	500	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	500	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	500	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	500	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	625	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	625	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	500	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	500	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	500	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	625	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	625	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	625	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	500	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	500	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	500	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	500	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	625	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	625	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	625	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	-	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	-	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	-	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	-	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	-	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	-	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	-	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	-	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	-	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	-	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	-	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	-	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	-	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	-	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	-	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	-	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	-	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	-	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	-	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	-	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	-	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	-	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	-	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	-	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	-	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	-	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	-	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	-	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	-	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	-	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	-	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	-	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	-	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	-	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	-	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	-	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	-	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	-	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	-	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	-	-

19 Jan, 2027

-
Included w.e.f. 10.05.2023

IS 3735 (1996)

Canvas Shoes, Rubber Sole

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	1250	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	1000	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	500	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	500	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	625	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	1000	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	500	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	625	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	625	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	625	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	1200	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	1500	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	1500	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	500	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	500	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	500	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	500	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	500	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	500	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	500	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	500	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	500	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	500	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	500	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	500	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	500	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	625	-
4.5(Finish )	-	500	-
4.6(Mass )	-	500	-
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	500	-

19 Jan, 2027

-
Amendment 5 included w.e.f. 09.10.2024

IS 11544 (1986)

Specification for slipper, rubber

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Shape & Design)	-	500	-
3.2(Relative density )	-	500	-
3.2(Hardness (IRHD))	-	500	-
3.2(Hardness after ageing)	-	1500	-
3.2(Flexural endurance)	-	2500	-
3.2.4(Mass per unit area)	-	500	-
3.2.4(End per cm)	-	500	-
3.2.4(Picks per cm)	-	500	-
3.2.4(Colour fasntess to washing)	-	420	-
3.2.5(Type of Thread)	-	500	-
3.2.6(Thickness of components)	-	500	-
Cl. 4, Cl. 4.1,Cl 4.2(Marking and packing)	-	500	-
3.2(Relative density )	-	-	-
3.2(Hardness (IRHD))	-	-	-
3.2(Hardness after ageing)	-	-	-
3.2(Flexural endurance)	-	-	-
3.2.4(Mass per unit area)	-	-	-
3.2.4(End per cm)	-	-	-
3.2.4(Picks per cm)	-	-	-
3.2.4(Colour fasntess to washing)	-	-	-
3.2.5(Type of Thread)	-	-	-
Cl. 4, Cl. 4.1,Cl 4.2(Marking and packing)	-	-	-
3.2.6(Thickness of components)	-	-	-

19 Jan, 2027

-
Included w.e.f. 10.05.2023

IS 6719 (1972)

Solid Pvc Soles And Heels

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	500	-
3.6 (i)(Relative density )	-	500	-
3.6 (ii)(Tensile Strength )	-	500	-
3.6 (iii)(Elongation at break, percent )	-	500	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	-
3.6 (v)(Volatility, percent by means )	-	1500	-
3.6 (vi)(Lead (as Pb) ppm)	-	1200	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	500	-
6 ,6.1,6.2,6.3(Test Method)	-	500	-

19 Jan, 2027

-
amendment included w.e.f 09.10.2024

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ii)(Hardness, Shore A durometer min)	-	500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	1500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vii)(Heat shrinkage test at 100±1°C for 1 hour max)	-	1500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ix)(Flexing resistance)	-	1500	-
5, 5.1(Marking)	-	500	-
6, 6.1(Packing)	-	500	-
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ii)(Hardness, Shore A durometer min)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vii)(Heat shrinkage test at 100±1°C for 1 hour max)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ix)(Flexing resistance)	-	-	-
5, 5.1(Marking)	-	-	-
6, 6.1(Packing)	-	-	-
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	-	-
4.2(Size & Thickness )	-	-	-

19 Jan, 2027

-
amendment included w.e.f 09.10.2024

IS 15644 (2006)

Safety of electric toys

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15644 Cl. 7(Marking and instructions)	-	500	-
15644 Cl. 9(Heating and abnormal operation)	-	2850	-
15644 Cl. 10(Electrical strength at operating temperature)	-	1140	-
15644 Cl. 11.1(Moisture resistance)	-	2500	-
15644 Cl. 11.2(Resistant to humidity)	-	2500	-
15644 Cl. 12(Electric strength at room temperature)	-	2500	-
15644 Cl. 13(Mechanical strength)	-	2499.96	-
15644 Cl. 14.1(Construction)	-	1140	-
15644 Cl. 14.2(Construction)	-	1140	-
15644 Cl. 14.3(Construction)	-	1140	-
15644 Cl. 14.4(Construction)	-	1140	-
15644 Cl. 14.5(Construction)	-	1140	-
15644 Cl. 14.6(Construction)	-	1140	-
15644 Cl. 14.7(Construction)	-	1140	-
15644 Cl. 14.8(Construction)	-	1140	-
15644 Cl. 14.9(Construction)	-	1140	-
15644 Cl. 14.1(Construction)	-	1140	-
15644 Cl. 14.11(Construction)	-	1140	-
15644 Cl. 14.12(Construction)	-	1140	-
15644 Cl. 14.13(Construction)	-	1140	-
15644 Cl. 14.14(Construction)	-	1140	-
15.1(Protection of cords and wires)	-	1140	-
15644 Cl. 15.2(Protection of cords and wires)	-	1140	-
15644 Cl. 16(Components)	-	500	-
15644 Cl. 17 Table-1(Screws and connections)	-	1425	-
15644 Cl. 17 Table-1(Nominal daimeter of screws made of insulating material)	-	1425	-
15644 Cl. 18(Clearance and creepage distance)	-	1425	-
15644 Cl. 19.1(Ball pressure test IEC 60695-10-2)	-	1425	-
15644 Cl. 19.2.1(Glow wire test IEC 60695-2-11)	-	1425	-
15644 Cl. 19.2.2(Needle flame test)	-	1425	-
15644 Cl. 20(Radiation, toxicity and similar hazards)	-	1500	-
8.0(Power Input)	-	1140	-
7.0(Marking and instructions)	-	1140	-

19 Jan, 2027

-
Excluding: Cl. 20.0 (Radiation, toxicity and similar hazards) and Cl. 16 (Components)

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

2000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	-
4.2.2(a)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	2000	-
4.2.2(b)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	2000	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	2000	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	2000	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	2000	-
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	2000	-
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	2000	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	-
4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	2000	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	2000	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
4.5-5.5(Soft-filled toys-rate of spread of flame )	-	2000	-
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	2000	-
4.1(General)	-	2000	-

19 Jan, 2027

-
-

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

6000 View breakup
Rs.6000/- (10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000		-
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000		-

19 Jan, 2027

-
-

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	950	-

19 Jan, 2027

-
-

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test)	-	750	-
4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys)	-	750	-
4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters)	-	1500	-
4.2 - 5.24.5( Reasonably foreseeable abuse -Torque test)	-	750	-
4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-	750	-
4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms)	-	750	-
4.2 - 5.24.6.4( Reasonably foreseeable abuse -Tension test for protective components)	-	750	-
4.2 - 5.24.6.5( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-	750	-
4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	750	-
4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	750	-
4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	750	-
4.3.2 - 5.21( Expanding materials)	-	1140	-
4.4.1 - 5.2(Small parts-For children under 36 months)	-	500	-
4.4.2 - 5.2(Small parts-For children 36 months and over but under 72 months )	-	500	-
4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-	500	-
4.5.1.3 - 5.3(Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months-Test for shape and size of certain toys)	-	500	-
4.5.1.4 - 5.3(Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys)	-	500	-
4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test)	-	500	-
4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	500	-
4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	500	-
4.5.5(Shape, size and strength of certain toys-Toy pacifiers-Nipple length)	-	500	-
4.5.6(Shape, size and strength of certain toys-Balloons)	-	750	-
4.5.7(Shape, size and strength of certain toys-Marbles)	-	1500	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	500	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening in Base)	-	500	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening not in Base)	-	500	-
4.5.8 - b(Shape, size and strength of certain toys-Hemispheric-shaped toys-Extension of divider)	-	500	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	500	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	500	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys)	-	500	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-The maximum distance between centrelines of adjacent peaks )	-	500	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-Minimum depth)	-	500	-
4.6.1 a - 5.8(Edges-Accessible sharp edges of glass or metal-Sharp edge test)	-	500	-
4.6.1 b(Edges-Accessible sharp edges of glass or metal- gap between the edge and the adjacent surface)	-	500	-
4.6.2(Edges-Functional sharp edges)	-	500	-
4.6.3 - 5.8(Edges-Edges on metal toys-Sharp edge test)	-	500	-
4.6.4( Edges-Edges on moulded toys)	-	500	-
4.6.5( Edges-Edges on exposed bolts or threaded rod)	-	500	-
4.7.1 - 5.9(Points-Accessible sharp points-sharp-point test)	-	500	-
4.7.2 - a(Points-Functional sharp points)	-	500	-
4.7.2 - b(Points-Functional sharp points)	-	500	-
4.7.3 (Wooden toys)	-	500	-
4.8.1(Projections-General requirments)	-	1500	-
4.9(a) - 5.24.8.2( Metal wires and rods-wires and other metallic components intended to be bent)	-	750	-
4.9(b) - 5.24.8.3( Metal wires and rods-wires likely to be bent)	-	750	-
4.9 - c( Metal wires and rods)	-	750	-
4.9 - c - 5.8( Metal wires and rods-Sharp edge test)	-	500	-
4.9 - c - 5.9( Metal wires and rods-Sharp Point test)	-	500	-
4.9 - c( Metal wires and rods-Minimum dia of spokes)	-	500	-
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys-average thickness)	-	750	-
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness)	-	750	-
4.11.2.1(a) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	1000	-
4.11.2.1(b) - 5.11.3( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-breakaway feature separation test)	-	1000	-
4.11.2.1(b) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	1000	-
4.11.2.2 - 5.11.2( Cords-Cords in toys intended for children under 18 months--Other cords-free length )	-	1000	-
4.11.3.1(a) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	1000	-
4.11.3.1(b) - 5.11.3( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-breakaway feature separation test)	-	1000	-
4.11.3.1(b) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	1000	-
4.11.3.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords)	-	1000	-
4.11.3.3 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords without a free end )	-	1000	-
4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test)	-	1000	-
4.11.4(a) - 5.11.4.2(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Elastic materials)	-	1000	-
4.11.4(b) - 5.11.3(Cords-Fixed loops and nooses intended for children under 36 months-Breakaway feature separation test)	-	1000	-
4.11.5 - 5.11.2(Cords-Cords on pull toys-free length)	-	1000	-
4.11.6(Cords- Electrical cables)	-	1000	-
4.11.7 - 5.11.1(Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional dimension)	-	1000	-
4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-	1000	-
4.11.9.1(Cords-Toys intended to be strung across a cradle, cot, perambulator or carriage)	-	1000	-
4.11.9.2 (Cords-Toys otherwise intended to be attached to a cradle, cot, perambulator or carriage)	-	1000	-
4.11.10(Cords-Cords on toy bags)	-	1000	-
4.11.11 - 5.11.6( Cords, strings and lines for flying toys- electrical resistance)	-	1000	-
4.12.1(a - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(a - 2)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(a - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	900	-
4.12.1(a - 4)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(a - 5) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(b - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(b - 2) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms)	-	900	-
4.12.2 (b)(Folding mechanisms-Other toys with folding mechanisms)	-	500	-
4.12.3(Folding mechanisms-Hinge line clearance)	-	900	-
4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials)	-	500	-
4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments)	-	500	-
4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-	500	-
4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	500	-
4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms)	-	500	-
4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys)	-	500	-
4.14(a)(Springs)	-	500	-
4.14(b)(Springs)	-	500	-
4.14(c)(Springs)	-	500	-
4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization)	-	1150	-
4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	1150	-
4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	1150	-
4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	1150	-
4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters)	-	1150	-
4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	1150	-
4.16.1(Enclosures-Ventilation)	-	500	-
4.16.1(Enclosures-Ventilation-No of openings)	-	500	-
4.16.1(Enclosures-Ventilation-Area of Each openings(If two openings))	-	500	-
4.16.1(Enclosures-Ventilation-Distance between openings(If two openings))	-	500	-
4.16.1(Enclosures-Ventilation-Area of Each openings(If One opening))	-	500	-
4.16.1(Enclosures-Ventilation-spacing(If One opening))	-	500	-
4.16.2.1(Enclosures-Closures-Lids, doors and similar devices)	-	1425	-
4.16.2.1 - 5.13.1(Enclosures-Closures-Lids, doors and similar devices-Test For closures)	-	1425	-
4.16.2.2(a)(Enclosures-Closures-Lid support for toy chests and similar toys)	-	1425	-
4.16.2.2(a) - 5.13.2.1(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support)	-	1425	-
4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys- After durability test for toy chest lids)	-	1425	-
4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support After durability test for toy chest lids)	-	1425	-
4.16.2.2(b) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-durability test for toy chest lids)	-	1425	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 2)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 4)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 5) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 2) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.2 (a) - 5.22.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.2 (b)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms)	-	900	-
4.16.2.2(c) - 5.13.2.2 - 4.12.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Hinge line clearance)	-	900	-
4.16.2.2(d)(Enclosures-Closures-Lid support for toy chests and similar toys)	-	1425	-
4.16.3(Enclosures-Toys that enclose the head)	-	1425	-
4.16.3(Enclosures-Toys that enclose the head-No of openings)	-	1425	-
4.16.3(Enclosures-Toys that enclose the head-Area of Each openings(If two openings))	-	1425	-
4.16.3(Enclosures-Toys that enclose the head-Distance between openings(If two openings))	-	1425	-
4.16.3(Enclosures-Toys that enclose the head-Area of Each openings(If One opening))	-	1425	-
4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	750	-
4.17(Simulated protective equipment, such as helmets, hats and goggles)	-	750	-
4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	500	-
4.18.2(b)(Projectile toys-Projectiles)	-	500	-
4.18.2(c)(Projectile toys-Projectiles)	-	500	-
4.18.2(c)(Projectile toys-Projectiles-Radius)	-	500	-
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	500	-
4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test)	-	750	-
4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup)	-	750	-
4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test)	-	750	-
4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup)	-	750	-
4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test)	-	500	-
4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing)	-	750	-
4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	1200	-
4.18.3(b)(Projectile toys-Projectile toys with stored energy)	-	1200	-
4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-	1200	-
4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	750	-
4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components)	-	750	-
4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	1200	-
4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism)	-	500	-
4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	750	-
4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	1200	-
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	500	-
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test)	-	750	-
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After torque test)	-	750	-
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective components)	-	750	-
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After tension test for protective components)	-	750	-
4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-	1200	-
4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	1200	-
4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	-
4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	-
4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	500	-
4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test)	-	750	-
4.18.4.6 - 5.24.5 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set- kinetic energy per area After torque test)	-	1200	-
4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective components)	-	750	-
4.18.4.6 - 5.24.6.4 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-kinetic energy per area After tension test for protective components)	-	1200	-
4.19(Rotors and propellers)	-	750	-
4.2(Aquatic toys)	-	500	-
4.21(a)(Braking)	-	750	-
4.21(a)(Braking-brake performance for mechanically or electrically powered ride-on toys other than toy bicycles)	-	1425	-
4.21(b)(braking)	-	750	-
4.22.1(Toy bicycles-Instructions for use)	-	750	-
4.22.2(Toy bicycles-Determination of maximum saddle height)	-	750	-
4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	1425	-
4.22.3 (Toy bicycles-Braking requirements- brake lever dimension(d))	-	750	-
4.22.3 (Toy bicycles-Braking requirements- lever Length(l))	-	750	-
4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	1425	-
4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	1150	-
4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases)	-	1425	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals))	-	1425	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	1425	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	1425	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals))	-	1425	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	1425	-
4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	1425	-
4.26(a) - 5.2( Mouth-actuated toys-small parts test)	-	500	-
4.26(b) - 5.24.5 - 5.3( Mouth-actuated toys-small parts test after torque test)	-	750	-
4.26(b) - 5.24.6.1 - 5.4( Mouth-actuated toys-small parts test after tension test, general procedure)	-	750	-
4.26(c ) - 5.20 - 5.2( Mouth-actuated toys-small parts test after durability of mouth-actuated toys)	-	750	-
4.27(Toy roller skates, toy inline skates and toy skateboards)	-	500	-
4.28( Percussion caps specifically designed for use in toys)	-	500	-
4.29(a) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(b) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(c) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(d) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(e) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.29(g) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	2000	-
4.30.2(Toy scooters-Warnings and instructions for use)	-	500	-
4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	1150	-
4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	1150	-
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	1150	-
4.30.3 - 5.27 - 5.8(Toy scooters-Strength-dynamic strength for toy scooters- sharp-edge test)	-	1500	-
4.30.3 - 5.27 - 5.9(Toy scooters-Strength-dynamic strength for toy scooters-sharp-point test)	-	1500	-
4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters)	-	1500	-
4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes)	-	1500	-
4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization)	-	1150	-
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	750	-
4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	750	-
4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	750	-
4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	750	-
4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	750	-
4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	750	-
4.30.6 ( Toy scooters-Braking)	-	750	-
4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy)	-	1500	-
4.30.7( Toy scooters-Wheel size(diameter))	-	500	-
4.30.8(Toy scooters-Projections)	-	500	-
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs Diameter))	-	500	-
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs space from end))	-	500	-
4.31(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over)	-	500	-
4.31.1 - 5.32(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-magnetic flux index)	-	900	-
4.31.1 - 5.2(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-small parts test)	-	500	-
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index)	-	900	-
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test)	-	500	-
4.31.2(b) - 5.34 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-soaking test for magnets-small parts test)	-	750	-
4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	1500	-
4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether)	-	750	-
4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k))	-	750	-
4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test)	-	1000	-
4.34(Sledges and toboggans with cords for pulling)	-	500	-
4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test)	-	500	-
9873 (Part - 3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	950	-
9873 (Part - 3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	950	-
9873 (Part - 3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	950	-
9873 (Part - 3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	950	-
9873 (Part - 3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	950	-
9873 (Part - 3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	950	-
9873 (Part - 3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	950	-
9873 (Part - 3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	950	-
9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000	-
9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000	-
4.1(Normal use)	-	2000	-
4.3.1(Material quality)	-	500	-
5.24.6.1(Tension Test General procedure)	-	750	-
9873 (Part - 1) 4.2.2 - 5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	-
9873 (Part - 1) 4.2.2(a) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	2000	-
9873 (Part - 1) 4.2.2(b) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	2000	-
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	-
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	2000	-
9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	2000	-
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	2000	-
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	2000	-
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	-
9873 (Part - 2) 4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	2000	-
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	-
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
9873 (Part - 2) 4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	-
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-rate of spread of flame )	-	2000	-
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-Test for soft-filled toys )	-	2000	-

19 Jan, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

Softlines and Electrical Safety Testing Laboratory TUV Rheinland India Pvt Ltd., Gurgaon (8167106)

330-331 Udyog Vihar Phase IV, Gurugram, Gurugram, Haryana, 122015

9711918976 g.kaur@ind.tuv.com

Scope List