BIS - LIMS (Laboratory Information Management System)

National Test House (NTH), Alipore, Kolkata-700027

11/1 Judges Court Road, Kolkata, Kolkata, Kolkata, West Bengal, 700027

9324565281 nthsal-wb@nic.in

Scope List

Reset

26 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	100	10% for each extra core
11.2(Legibility)	-	100	10% for each extra core
11.1(Durability)	-	100	10% for each extra core
11(Identification)	-	100	10% for each extra core
10.4(Flammability test- Unaffected portion)	-	250	10% for each extra core
10.4(Flammability test-Burning after flame removal)	-	250	10% for each extra core
table 1 e) 3) (IR constant- max. Temp)	-	500	10% for each extra core
table 1 e) 3) (IR constant- Room temp )	-	500	10% for each extra core
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	10% for each extra core
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	10% for each extra core
10.2(HV (room temperature))	-	1000	10% for each extra core
10.1(HV (water immersion))	-	1500	10% for each extra core
10.8(Smoke density rating)	-	3500	10% for each extra core
10.6(Halogen evolution)	-	3500	10% for each extra core
10.7(Temperature index)	-	3500	10% for each extra core
10.5(Oxygen index)	-	3500	10% for each extra core
Table 1 iii) d) 9)(Cold impact for sheath)	-	0	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	0	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	0	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	0	-
Table 1(Category Code)	-	100	10% for each extra core
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	10% for each extra core
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	10% for each extra core
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	10% for each extra core
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	10% for each extra core
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	10% for each extra core
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	10% for each extra core
Table 1 iii) d) 4)(Cracks Observed)	-	250	10% for each extra core
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	250	10% for each extra core
Table 1 iii) c) 4)(Cracks Observed)	-	250	10% for each extra core
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	250	10% for each extra core
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	10% for each extra core
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	10% for each extra core
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	250	10% for each extra core
Table 1 iii) d) 3)(Sheath- TS variation)	-	250	10% for each extra core
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	250	10% for each extra core
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	250	10% for each extra core
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	350	10% for each extra core
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	350	10% for each extra core
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	350	10% for each extra core
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	50	10% for each extra core
8.3(Thickness of Sheath)	-	100	10% for each extra core
9.1(Ovality)	-	100	10% for each extra core
9(Overall dimensions)	-	100	10% for each extra core
10.11(Per sulphate test (for tinned Cu cable only))	-	100	10% for each extra core
4.2(Conductor resistance test)	-	1500	10% for each extra core
4.1(Wrapping test (for Al))	-	500	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	300	-
4.1(Annealing test (for copper))	-	1000	-
Cl. 8.2(Application of Sheath)	-	100	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
10.1(High Voltage Test (Water Immersion Test))	-	1000	10% for each extra core
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	250	10% for each extra core
Table 1 iii) c) 3)(Elongation variation)	-	250	10% for each extra core
Table 1 iii) c) 3)(TS variation)	-	250	10% for each extra core
Table 1 iii) c) 3)(Elongation (After ageing))	-	250	10% for each extra core
Table 1 iii) c) 1)(Elongation (Without ageing))	-	350	10% for each extra core
5.2(Application )	-	100	-
5.3(Thickness of Insulation)	-	100	10% for each extra core
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	50	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	50	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	50	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	50	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	50	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	50	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	50	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	50	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	50	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	100	-
12(CONSTRUCTION Core Identification)	-	100	-
8.1(Sheath Material )	-	100	-
7(Binder Tape)	-	100	-
6.2(Filler)	-	100	-
6.1(Filler)	-	100	-
5.1(Insulation)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.1(Conductor - Material)	-	100	-
4.1(Conductor - Material)	-	100	-
10.11(Persulphate Test )	-	500	-
12.0(Core identification)	-	100	-
4, IS 8130(Construction of conductor)	-	100	-
Table 2, IS 8130(No fo wire in a conductor)	-	100	-
8.3(Minimum thickness of Sheath)	-	100	-
8.3(Avarage thickness of Sheath)	-	100	-
5.3(Minimum thickness of insulation)	-	100	10% for each extra core
5.3(Avarage thickness of insulation)	-	100	10% for each extra core
Table 4(Copper purity test)	-	500	-
10.3(Spark test)	-	0	-
table 1, 4.2(insulation resistance test)	-	100	10% for each extra core
5.4(Mechanical properties before and after ageing)	-	100	10% for each extra core
10.3(Spark Test)	-	0	-
4.1(Material)	-	100	-
4.2(Electrical Resistance)	-	1500	10% for each extra core
5(INSULATION)	-	100	-
6(FILLER)	-	100	-
7(BINDER TAPE)	-	100	-
8(SHEATH)	-	100	-
9(OVERALL DIMENSIONS)	-	100	-
10.2(High Voltage Test (at Room Temperature))	-	500	10% for each extra core
10.3(Spark Test)	-	0	-
10.4(Flammability Test)	-	200	-
10.5(Oxygen Index Test)	-	3500	-
10.6(Test for Halogen Acid Gas Evolution)	-	3500	-
10.7(Test for Temperature Index)	-	3500	-
10.8(Smoke Density Rating)	-	3500	-
10.11(Persulphate Test)	-	500	-
11(IDENTIFICATION)	-	100	-
12(CORE IDENTIFICATION)	-	100	-
13(CABLE CODE)	-	100	-
15(PACKING AND MARKING)	-	50	-
16.1(Construction)	-	100	-
16.2(Tests)	-	0	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	100	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	100	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	100	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	100	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	100	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	100	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	100	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	100	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	100	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	100	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	100	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	100	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	100	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	100	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	100	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	100	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	100	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	100	-
Cl.19.1.4(Assembly of Cores)	-	100	-
10.1(HV (water immersion))	-	1500	10% for each extra core
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	2000	-

08 Apr, 2027

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	0	-
6.5(Size of messenger conductor )	-	0	-
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	250	10% EXTRA FOR EACH CORE
7.3(Tolerance on thickness of insulation )	-	250	10% EXTRA FOR EACH CORE
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	0	-
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	0	-
9.3(Direction of lay)	-	0	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	0	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	10% EXTRA FOR EACH CORE
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	250	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	250	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	250	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	250	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	250	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	250	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	250	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	250	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	250	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	250	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	250	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	0	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	0	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	10% EXTRA FOR EACH CORE
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	10% EXTRA FOR EACH CORE
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	10% EXTRA FOR EACH CORE
6.1(Construction of phase conductor)	-	0	-
6.1(Number of wires (phase conductor))	-	0	-
6.1(Construction of Street Lighting conductor)	-	0	-
6.1(Number of wires (Street Lighting conductor))	-	0	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	0	-
11.4(Bending Test on the Completed Cable ( Optional))	-	0	-

08 Apr, 2027

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	0	-
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
6(ARMOURING)	-	0	-
7(OUTER SHEATH)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	1000	10% extra for each core
9.3(Thickness of Insulation - Minimum)	-	500	10% extra for each core
9.4(Application of Insulation)	-	0	-
10.1(Core Identification)	-	0	-
10.2(Core Identification- Neutral)	-	0	-
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	0	-
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(Armouring: Direction of Lay )	-	0	-
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	2000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2000	-
13.6 g)(ARMOURING: Resistivity)	-	2000	-
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	500	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	500	-
15.1 a) iv)(Resistance test - Main conductor)	-	2000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	0	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	750	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	750	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	500	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	500	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	500	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	500	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	500	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	500	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	2000	10% extra for each core
16.2(HIGH VOLTAGE TEST )	-	2000	10% extra for each core
16.3(FLAMMABILITY TEST : Period of Burning )	-	250	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	250	-
16.9(Oxygen Index Test)	-	5000	-
16.1(Flame Retardance Test on Single Cables)	-	5000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	0	-
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	500	-
15.4 (b)(Cold impact)	-	500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	500	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	500	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	500	-
Table 4(Copper purity test)	-	500	-
Cl No. 16.15(Smoke density test)	-	5000	-
Table 2(Cold Impact test for Outer sheath)	-	500	-
Table 2(Cold bend test for Outer sheath)	-	500	-
Cl 16(Halogen Acid Gas Test)	-	5000	-
Cl 16(Halogen Acid Gas Test)	-	5000	-
Cl 16(Halogen Acid Gas Test)	-	5000	-
Cl.8(Conductor)	-	0	-
Cl.8(Conductor)	-	0	-
Cl.8(Conductor)	-	0	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	500	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	500	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	2000	-
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-

08 Apr, 2027

-
-

IS 15549 (2005)

Stationary valve regulated lead acid batteries - Specification

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.1(Test for C 10 Capacity)	-	20000	----
12.2(Test for C 1 Capacity)	-	20000	----
12.4(Ampere Hour Efficiency)	-	10000	---
12.5(Watt Hour Efficiency)	-	10000	----
12.6(Test for Retention of Charge)	-	10000	----
12.9 & Annex C(Test for Oxygen Recombination Efficiency)	-	10000	----
12.1(Endurance Life Cycle Test)	-	40000	-----

08 Apr, 2027

-
-

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13.1(Marking (Rating Plates))	-	1000	-
13.2(Terminal Marking Plate)	-	0	-
13.3(Marking )	-	1000	-
13.4(Marking)	-	1000	-
13.4.1(Marking)	-	1000	-
21.2 a)(Measurement of winding resistance )	-	1000	-
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	1500	-
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	6000	-
21.2 d)(Measurement of no-load loss and current)	-	5500	-
21.2 e)(Measurement of insulation resistance)	-	1000	-
21.2 f)(Induced over-voltage withstand test)	-	2500	-
21.2 g)( Separate-source voltage withstand test)	-	2500	-
21.5.3.3(Oil leakage test)	-	7000	-
21.3(b)(Temperature-rise test)	-	30000	-
21.4 a)( Determination of sound levels)	-	6000	-
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	10000	-
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	5000	-
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	10000	-
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	5000	-
21.5.2.3( Oil leakage test (routine test))	-	7000	-
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	5000	-
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	5000	-
21.4 c(No load current at 112.5 percent voltage.)	-	2000	-
21.4 d(Paint adhesion tests)	-	5000	-
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	10000	-
11(Minimum clearance in Air)	-	1000	-
21.5.1.3(Oil leakage test upto 200 KVA)	-	7000	-
6.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
7.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
8.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
6.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
7.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
8.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
21.5.3.3(Oil leakage test (routine test))	-	7000	-
6.9(Permissible Flux Density and Over Fluxing )	-	10000	-
6.1(Limits of Temperature-rise)	-	30000	-
11(Minimum Clearnaces air )	-	1000	-

08 Apr, 2027

-
-

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

32500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
7.1.1(Diameter of Core Wire)	-	500	-
7.1.2(Length of Electrodes)	-	500	-
7.2.1(Contact End)	-	500	-
7.2.2(Arc striking End)	-	500	-
7.3(Concentricity of Flux covering with core wire)	-	2000	-
7.4(Defects of Core wire and Coverings)	-	500	-
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	1000	-
9.1.2 Table 6 ( Yield Stress -Annex F)	-	1000	-
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	1000	-
9.2(Butt Weld Bend Test-IS 1599)	-	8000	-
9.1.3 Table 6 ( Impact Strength-Annex F)	-	4000	-
9.3(Running PerformanceTest-Annex H)	-	2000	-
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	-
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	-
9.6(Radiographic Test- IS 1182)	-	1000	-

08 Apr, 2027

-
-

IS 428 (2013)

Washable distemper - Specification (Third Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.9.2.1(Volatile organic compounds (Requirement for Eco-Mark))	-	1500	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. ix)(Accelerated storage stability)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. viii)(Resistance to alkali)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vii)(Recoating Properties)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vi)(Residue on sieve, Type 2)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vi)(Residue on sieve, Type 1)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. v)(Fastness to light)	-	8000	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. iv)(Colour)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. iii)(Finish)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. ii)(Consistency )	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) b)(Drying Time a) Hard Dry, Type 2)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) b)(Drying Time a) Hard Dry, Type 1)	-	1200	Without GST
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) a)(Drying Time a) Surface Dry, Type 2)	-	1200	Without GST
Cl.6.6(Keeping Proterties)	-	12500	As keeping properties includes all tests in Table-1 of IS 428:2013 including 2580hrs of Fastness to light test Without GST
Cl.6.5(Lead Restriction)	-	1200	Without GST
Cl.6.3(Application)	-	1200	Without GST
Cl.6.2(Thining)	-	1200	Without GST
Cl.6.1(Foam and condition)	-	1200	Without GST

08 Apr, 2027

-
-

IS 5410 (2013)

Cement paint - Specification (Second Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.7(Keeping Properties)	-	12500	As keeping properties includes all tests in Table-1 of IS 5410:2013 Without GST
Cl.4.8, 7.1 - Table 1 ix)(Recoating Properties)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 viii)(Pot life of mixed paint)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 vii)(Water Repellency)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 vi)(Resistance to dry rubbing)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 iv)(Fastness to light)	-	8000	Without GST
Cl.4.8, 7.1 - Table 1 iii)(Colour)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 ii)(Finish)	-	1200	Without GST
Cl.4.8, 7.1 - Table 1 i)(Drying Time, Hard Dry)	-	1200	Without GST
Cl.4.6(Durability)	-	1200	Without GST
Cl.4.4(Lead Restriction)	-	1200	Without GST
Cl.4.2(Preparation for Use)	-	1200	Without GST
Cl.4.1.1(Freedom from Organic Binders)	-	1200	Without GST
Cl.4.1(Composition - Hydrated Lime)	-	3000	Without GST
Cl.4.1(Composition - Portland Cement)	-	3000	Without GST

08 Apr, 2027

-
-

IS 427 (2013)

Distemper, dry, colour as required - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Form and Condition)	-	250	-
4.2.1(Composition)	-	250	-
4.3.1(Lead restriction)	-	1000	-
4.2.2 & 7, Table-1(i)(Drying time)	-	250	-
4.2.2 & 7, Table-1(ii)(Consistency)	-	250	-
4.2.2 & 7, Table-1(iii)(Finish)	-	250	-
4.2.2 & 7, Table-1(iv)(Colour)	-	250	-
4.2.2 & 7, Table-1(v)(Fastness to light)	-	8000	250 hrs exposure by Xenon Arc apparatus
4.2.2 & 7, Table-1(vi)(Residue on seive)	-	250	-
4.2.2 & 7, Table-1(vii)(Recoating properties)	-	250	-
4.2.2 & 7, Table-1(viii)(Resistance to alkali)	-	500	-
4.2.2 & 7, Table-1(ix)(Resistance to dry rubbing)	-	500	-

08 Apr, 2027

-
-

IS 15769 (2008)

Flux cored (Tubular) electrodes for gas shielded and self - Shielded metal welding of carbon or carbon - Manganese steel

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Radiographic Soundness Test)	-	1000	-
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	3000	-
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	3000	-
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	3000	-
5.6(Longitudinal Bend Test)	-	8000	-
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	5000	-
5.8 (Table No.- 15)(Chemical Composition,%)	-	5000	-
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause

08 Apr, 2027

-
Included w.e.f.18.08.2025

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	500	10 % extra for each core
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	1000	10 % extra for each core
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	2000	-
13.5.2(ARMOURING : Resistance)	-	2000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2000	-
13.6 g)(ARMOURING: Resistivity)	-	2000	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	500	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	500	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	500	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	500	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	2000	10 % extra for each core
15.1 a) 4)(Resistance test - Neutral conductor )	-	2000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	500	10 % extra for each core
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	500	10 % extra for each core
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	500	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	500	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	500	10 % extra for each core
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	500	10 % extra for each core
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	500	10 % extra for each core
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	500	10 % extra for each core
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	500	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	10 % extra for each core
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	10 % extra for each core
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	10 % extra for each core
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	10 % extra for each core
15.1 d)4)(Hot deformation : Insulation )	-	500	10 % extra for each core
15.1 d)4)(Hot deformation : Sheath )	-	500	10 % extra for each core
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1500	10 % extra for each core
15.1 d)5)( Loss of mass in air oven- sheath )	-	1500	-
15.1 d)6)(Heat shock test- Insulation )	-	500	10 % extra for each core
15.1 d)6)(Heat shock test- sheath )	-	500	-
15.1 d)7)(Thermal stability- insulation )	-	1000	10 % extra for each core
15.1 d)7)(Thermal stability- Sheath )	-	1000	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	10 % extra for each core
15.1 e)(Insulation resistance test : IR Constant )	-	500	10 % extra for each core
15.1 f)(High voltage test ( water immersion test ))	-	3000	10 % extra for each core
15.1 g)(High voltage test at room temperature)	-	1000	10 % extra for each core
15.1 g)(High voltage test at room temperature)	-	1000	10 % extra for each core
15.4 a)(Cold bend test- Insulation ( Optional test))	-	0	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	0	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	0	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	0	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	0	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	10 % extra for each core
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1500	10 % extra for each core
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1500	10 % extra for each core
16.4(Flammability Test)	-	500	-
16.5(Oxygen Index Test)	-	4000	-
16.6(Flame Retardance Test on Single Cables)	-	5000	-
16.7(Flame Retardance Test on Bunched Cables)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	1000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	10 % extra for each core
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	500	10 % extra for each core
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1500	10 % extra for each core
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1500	10 % extra for each core
16.4(Flammability Test- Un affected portion)	-	500	-
16.4(Flammability Test- Period of Burning)	-	500	-
9.3(Minimum Thickness of Reduce core insulation)	-	500	-
9.2(Thickness of Reduce core insulation)	-	500	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	5000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	1000	10 % extra for each core
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
Cl No. 16.10(Smoke density test)	-	5000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	500	-

08 Apr, 2027

-
Included.w.e.f.23.01.2025

IS 133 (2013)

ENAMEL, INTERIOR : (A) UNDERCOATING (B) FINISHING

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1()	-	0	-
5.4(IS 101 (Part 1/Sec 2))	-	1000	-
5.5()	-	1000	-
5.6()	-	1000	-
5.7(IS 133Annex B.)	-	1000	-
5.8(IS 101 (Part 8/Sec 5).)	-	1000	-
Table 1 Cl No 5.9,i(IS 101 part 3 sec 1)	-	1000	-
Table 1 5.9,ii(IS 101 Part l/Sec 7)	-	1000	-
Table 1 Cl No 5.9,i(IS 101 part 3 sec 2)	-	1000	-
Table 1 Cl No 5.9,i(IS 101 part 3 sec 3)	-	1000	-
Table 1 5.9,iii(Part 1/Sec 5)	-	1000	-
Table 1 5.9, iv((Part 3/Sec 4))	-	1000	-
Table 1 5.9, iv(Part 4/Sec 4)	-	1000	-
Table 1 5.9,v(Part 3/Sec 5)	-	1000	-
Table 1 5.9,vi(Qualitative IS 5)	-	1000	-
Table 1 5.9,vii(Part 4/Sec 1)	-	1000	-
Table 1 Cl No 5.9 Vii(Part 4/Sec 3)	-	5000	-
Table 1 5.9,ix(IS 133Annex E.)	-	1000	-
Table 1 5.9,x(3 of (Part 5/Sec 2))	-	1000	-
Table 1 5.9,x(2 of (Part 5/Sec 2))	-	1000	-
Table 1 5.9,xi((Part 1/Sec 6))	-	1000	-
Table 1 5.9,xii((Part 8/Sec 6)	-	1000	-
Table 1 5.9,xiii(IS 133Annex F.)	-	1000	-
Table 1 5.9,xiv(Part 6/Sec 2)	-	1000	-

08 Apr, 2027

-
-

IS 13369 (1992)

Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

101000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 11.2(IS 13369-1992, Amndt. 1 to 3)	-	500	---
Cl. 11.4(IS 13369-1992, Amndt. 1 to 3)	-	500	---
Cl. 11.5(IS 13369-1992, Amndt. 1 to 3)	-	20000	---
Cl. 11.8(IS 13369-1992, Amndt. 1 to 3)	-	10000	---
Cl. 11.6(IS 13369-1992, Amndt. 1 to 3)	-	10000	---
Cl. 11.7(IS 13369-1992, Amndt. 1 to 3)	-	40000	---
Cl. 11.9(IS 13369-1992, Amndt. 1 to 3)	-	10000	---
Cl. 11.10(IS 13369-1992, Amndt. 1 to 3)	-	10000	---

08 Apr, 2027

-
(12V & upto 200Ah capacity)

IS 1651 (2013)

Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification (Fourth Revision)

121500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 12.2(IS 1651-2013)	-	500	---
Cl. 12.3(IS 1651-2013)	-	500	---
Cl. 12.4(IS 1651-2013)	-	500	---
Cl. 12.5(IS 1651-2013)	-	25000	---
Cl. 12.10(IS 1651-2013)	-	5000	---
Cl. 12.9(IS 1651-2013)	-	10000	---
Cl. 12.7(IS 1651-2013)	-	5000	---
Cl. 12.8(IS 1651-2013)	-	45000	---
Cl. 12.11(IS 1651-2013)	-	5000	---
Cl. 12.12(IS 1651-2013)	-	10000	---
Cl. 12.13(IS 1651-2013)	-	15000	---

08 Apr, 2027

-
(2V/12V & upto 800Ah capacity)

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.7(Markings and instructions)	-	1000	--
2.1(Protection from electric shock and energy hazards)	-	1000	---
1.6(Power interface .)	-	2000	-
2.2(SELV circuits)	-	2000	-
2.5(Limited power sources .)	-	2000	-
2.6(Provisions for earthing and bonding)	-	5000	-
2.7(Overcurrent and earth fault protection in primary circuits)	-	5000	-
2.9(Electrical insulation)	-	2000	-
2.10(Clearances, creepage distances and distances through insulation)	-	2000	-
3.1(General)	-	2000	-
3.2(Connection to a mains supply)	-	2000	-
4.2(Mechanical strength)	-	5000	-
4.3(Design and construction)	-	2000	-
4.4(Protection against hazardous moving parts)	-	5000	-
4.5(Thermal requirements)	-	2000	-
4.6(Openings in enclosures)	-	2000	-
5.1(Touch current and protective conductor curren)	-	2000	-
5.2(Electric strength)	-	5000	-
5.3(Abnormal operating and fault conditions)	-	1000	-

08 Apr, 2027

-
Excluding following tests: 1.Components (Cl. 1.5), 2.TNV Circuit (CL :2.3) 3.Moving parts (Cl. 2.8.5), 4. Switches & Relays-Overload test (Cl. 2.8.7.2), 5. Switches & Relays-Endurance test (Cl. 2.8.7.3), 6. Semiconductor devices (Cl. 2.10.5.4), 7. Insulation in wound components (Cl. 2.10.5.11), 8. Wire in wound components (Cl. 2.10.5.12), 9. Wire with solvent-based enamel in wound components (Cl.2.10.5.13), 10. Additional insulation in wound components (Cl. 2.10.5.14), 11. Construction of printed Boards( Cl.2.10.6) 12. Tests on coated printed boards and coated components sample preparation and preliminary inspection (Cl. 2.10.8.1), 13. Tests on coated printed components- Thermal Conditioning (Cl. 2.10.8.2), 14. Tests on coated printed boards & coated components- Abrasion resistance (Cl. 2.10.8.4), 15. Appliance inlets (Cl. 3.2.4), 16. Power Supply Cords (Cl. 3.2.5), 17. Mechanical strength test (Cathode ray tube) (Cl. 4.2.8), 18. Radiation (Cl. 4.3.13), 19. Conditions for a fire enclosure (Cl. 4.7.2), 20. Materials (Cl. 4.7.3), 21. Motors (Cl. 5.3.2), 22. Transformers (Cl. 5.3.3), 23. Electromechanical components (Cl. 5.3.5), 24. Simulation of faults (Cl. 5.3.7), 25. Unattended equipment (Cl.5.3.8) 26. Impulse test ( Cl.7.4.3)

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	-
7(Heating under normal operating conditions)	-	5000	-
8(Constructional requirements with regard to the protection against electric shock)	-	5000	-
9(Electric shock hazard under normal operating conditions)	-	5000	-
10(Insulation requirements)	-	5000	-
11(Fault conditions)	-	5000	-
12(Mechanical strength)	-	5000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	2000	-
14(Components)	-	5000	-
15(TERMINALS)	-	1000	-
16(External flexible cords)	-	5000	-
17(Electrical connections and mechanical fixings)	-	5000	-

08 Apr, 2027

-
Excluding following tests: 1. Ionizing radiation test (Cl.6.1), 2. Laser radiation (Cl.6.2), 3. Requirements for Endurance test for wound components with insulated winding wires without additional interleaved insulation (Cl.8.17), 4. Measurement of transient Voltage : ( Cl.13.3.4) 5. Component test (Cl.14) 6. Plug and socket( Cl.15.1) 7. External Flexile Cord (Cl.16.3), 8. Mechanical Strength of Picture Tubes for intrinsically protected Picture tubes (Cl.18.1) 9. Mechanical Strength of Picture Tubes for non-intrinsically protected Picture tubes (Cl. 18.2) 10. Electrical Component (Cl. 20.2), 11. Internal Wiring (Cl. 20.2.3), 12.Printed Boards (Cl. 20.2.4), 13.Components and parts not covered by 20.2.2, 20.2.3 and 20.2.4 (Cl. 20.2.5); 14. Fire Enclosure ( Cl. 20.3) 15. Heat Resistance of Insulating Materials (Cl.7.2) 16. Printed Boards (Cl.13.5) 17. Remote control device held in hand (Tumbling barrel), (Cl.12.3)

IS 16270 (2014)

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

220000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Capacity test)	-	20000	----
8.2(Endurance test)	-	80000	----
8.3(Charge retention test)	-	10000	---
8.4(Cycle endurance in Photovoltaic application)	-	90000	----
8.5(Sulphation Test)	-	10000	-----
8.6(Water loss test)	-	10000	-----

08 Apr, 2027

-
(2V/12V & upto 800Ah capacity) For lead acid batteries only

IS 7372 (1995)

Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

191500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.3 of IS 7372:1995(Physical Examination)	-	500	---
Cl 9.4 of IS 7372:1995(Dimensions and Layout)	-	500	----
Cl 9.5 of IS 7372:1995(Marking)	-	500	-----
Cl 9.6 of IS 7372:1995(Air Pressure Test)	-	10000	----
Cl 9.7 of IS 7372:1995(9.7 Capacity Test)	-	25000	----
Cl 9.8 of IS 7372:1995(Vibration Test)	-	10000	----
Cl 9.9 of IS 7372:1995(High-Rate Discharge Test at Normal Temperature)	-	15000	-----
Cl 9.10 of IS 7372:1995(High-Rate Discharge Test at Low Temperature)	-	20000	----
Cl 9.12 of IS 7372:1995(Retention of Charge Test)	-	15000	-----
Cl 9.13 of IS 7372:1995(Resistance to Overcharge Test)	-	10000	-----
Cl 9.14 of IS 7372:1995(Life Test)	-	60000	-----
Cl 9.15 of IS 7372:1995(Storage Test)	-	25000	----

08 Apr, 2027

-
(12V & upto 200Ah capacity)

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Freedom from Coarse Particles)	-	1200	Without GST
6.4(Skin Formation)	-	1200	Without GST
6.5(Thinning Properties)	-	1200	Without GST
6.6(Application Properties)	-	1200	Without GST
6.8(Lead Restriction)	-	1200	Without GST
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-	1200	Without GST
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-	1200	Without GST
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-	1200	Without GST
6.9 Table 2 ( 2) Mass, (Finishing ) )	-	1200	Without GST
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-	1200	Without GST
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-	1200	Without GST
6.9 Table 2 (b) Hard dry ( Under coating ) )	-	1200	Without GST
6.9 Table 2 (b) Hard dry, (Finishing ) )	-	1200	Without GST
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-	1200	Without GST
6.9 Table 2 (4) a) Finish (Under coating ) )	-	1200	Without GST
6.9 Table 2 (4) a) Finish (Finishing) )	-	1200	Without GST
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-	1200	Without GST
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-	1200	Without GST
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-	1200	Without GST
6.9 Table 2 (5) Fineness of grind,(Finishing))	-	1200	Without GST
6.9 Table 2 (6) Colour , (Finishing))	-	1200	Without GST
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-	1200	Without GST
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-	1200	Without GST
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-	1200	Without GST
6.9 Table 2 (9) Composition: a) Volume solids ( Under coating ))	-	3000	Without GST
6.9 Table 2 (9) Composition: a) Volume solids ( Finishing))	-	3000	Without GST
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-	3000	Without GST
6.9 Table 2 (10) Resistance to acid ( Under coating & Finishing ))	-	1200	Without GST
6.9 Table 2 (11) Resistance to alkali ( Under coating & Finishing ))	-	1200	Without GST
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-	1200	Without GST
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-	2000	Without GST
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-	1200	Without GST
6.7.1.3(QUV apparatus)	-	10000	Without GST

08 Apr, 2027

-
-

IS 2074 (2015)

Ready mixed paint, air drying, red oxide - Zinc chrome, priming - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1 (a)(Composition, Pigment, Cl 5.1.1)	-	1500	Without GST
Cl 5.1 (b)(Composition, Driers)	-	1500	Without GST
Cl 5.1 .1 (a)(Zinc chrome, (Type 2 of IS 51), Annex B)	-	1500	Without GST
Cl 5.1 .1 (b)(Synthetic red oxides of iron (conforming to Grade 2 or IS 44), (conforming to Grade 3 of IS 44), 6 of IS 6947 (Part 2))	-	1500	Without GST
Cl 5.1 .1 (c)(Suitable extenders)	-	2999.98	Without GST
Cl 5.1.2(Volatile vehicle)	-	1200	Without GST
Cl 5.2(Material)	-	1200	Without GST
Cl 5.3(Compatibility with Thinner, IS 1872)	-	1200	Without GST
Cl 5.4(Freedom from Objectionable Impurities)	-	1200	Without GST
Cl 5.5(Lead Restriction, IS 101(Part 8/Sec 5))	-	1200	Without GST
1 (i) (a) Table 1(Consistency, Annex C)	-	1200	Without GST
1 (i) (b) Table 1(Viscosity by ford cup No. 4, IS 101 (Part1/sec5))	-	1200	Without GST
1 (ii) Table 1(Mass, IS 101 (Part1/sec7))	-	1200	Without GST
1 (iii) (a) Table 1(Drying time, Surface Dry, IS 101 (Part3/sec1))	-	1200	Without GST
1 (iii) (b) Table 1(Drying time, Hard Dry, IS 101 (Part3/sec1))	-	1200	Without GST
1 (iv) (a) Table 1(Finish, IS 101 (Part3/sec4))	-	1200	Without GST
1 (iv) (b) Table 1(Gloss, IS 101 (Part4/sec4))	-	1200	Without GST
1 (v) Table 1(Fineness of grind, IS 101 (Part 3/Sec 5))	-	1200	Without GST
1 (vi) Table 1(Colour, IS 101 (Part 4/Sec 2))	-	1200	Without GST
1 (vii) (a) Table 1(Flexibility and adhesion: Bend test (with 6.25 mm dia mandrel and in type 1 apparatus), Clause 2 of IS 101 (Part 5/Sec 2))	-	1200	Without GST
1 (vii) (b) Table 1(Scratch hardness (load 1 000g), Clause 3 of IS 101 (Part 5/Sec 2))	-	1200	Without GST
1 (viii) Table 1(Flash point, IS 101 (Part l/Sec 6))	-	1200	Without GST
1 (ix) Table 1(Volume solids, IS 101 (Part 8/Sec 6))	-	3000	Without GST
1 (x) (a) Table 1(Resistance to humidity under condition of condensation: Resistance to humidity, Clause 2 of IS 101 (Part 6/Sec 1))	-	5000	Without GST
1 (x) (b) Table 1(Resistance to humidity under condition of condensation: Resistance to sea water (applicable for marine paints only), Annex D)	-	5000	Without GST
1 (x) (c) Table 1(Resistance to humidity under condition of condensation: Resistance to salt spray, Annex E)	-	5000	Without GST
1 (xi) Table 1(Accelerated storage stability test, Annex F)	-	1200	Without GST
1 (xii) Table 1, Cl.5.6(Keeping properties 1. Visual observation [Cl.3.1, table 1 of IS 101 (Part 6/Sec 2)])	-	1200	Without GST

08 Apr, 2027

-
-

IS 12744 : Part 1 (2013)

Ready mixed paint, air drying, red oxide - Zinc phosphate, priming - Specification: Part 1 for domestic and decorative applications (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.3, 8.1 - Table 1 -xiii)(Keeping Properties)	-	3000	-
Cl.5.3, 8.1 - Table 1 -xii)(Mass)	-	250	-
Cl.5.3, 8.1 - Table 1 -xi)(Flash Point)	-	1000	-
Cl.5.3, 8.1 - Table 1 -x) b)(Resistance to humidity under conditions of condensation a) Resistance to Salt Spray (for 96 Hours))	-	500	-
Cl.5.3, 8.1 - Table 1 -x) a)(Resistance to humidity under conditions of condensation a) Resistance to humidity (for 7 days))	-	500	-
Cl.5.3, 8.1 - Table 1 -ix) b)(Flexibility and adhesion b) Bent Test (with 6.25 mm dia mendrel in type 1 apparatus)	-	500	-
Cl.5.3, 8.1 - Table 1 -ix) a)(Flexibility and adhesion a) Scratch Hardness (Load 800 g))	-	500	-
Cl.5.3, 8.1 - Table 1 -viii)(Red Oxide (as Fe2O3) )	-	1000	-
Cl.5.3, 8.1 - Table 1 -vii)(Zinc Phosphate)	-	1000	-
Cl.5.3, 8.1 - Table 1 -vi)(Pigment Content)	-	1000	-
Cl.5.3, 8.1 - Table 1 -v)(Wet Opacity)	-	250	-
Cl.5.3, 8.1 - Table 1 -iv)(Colour in Natural Daylight)	-	250	-
Cl.5.3, 8.1 - Table 1 -iii)(Finish)	-	250	-
Cl.5.3, 8.1 - Table 1 -ii)(Consistency )	-	250	-
Cl.5.3, 8.1 - Table 1 -i)(Drying time hard dry)	-	250	-
Cl.5.2(Lead Restriction)	-	1000	-

08 Apr, 2027

-
Included w.e.f. 04.01.2024

IS 2339 (2013)

Aluminium paints for general purposes - Specification (First Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Composition)	-	2000	leafing property as per IS 289
5.2(Lead Restriction)	-	1000	-
5.3/8.1 (i)(Drying time)	-	500	-
5.3/8.1 (iv)(Mass)	-	500	-
5.3/8.1 (v)(Wet opacity)	-	500	-
5.3/8.1 (vi)(Flexibility and adhesion, bend test)	-	500	-
5.3/8.1 (vii)(Resistance to humidity under condition of condensation)	-	2500	-
5.3/8.1 (viii)(Flash point)	-	1000	-
5.3, 8.1, Table 1(Consistency)	-	500	-
5.3/8.1 (ix)(Keeping properties)	-	3000	-

08 Apr, 2027

-
Included w.e.f. 04.01.2024

IS 15489 (2013)

Paint, plastic emulsion - Specification (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Composition)	-	250	-
6.2(Conditions in the Container)	-	250	-
6.3(Thinning)	-	250	-
6.4(Application Properties)	-	250	-
6.5(Mass in kg/10 litre)	-	250	-
6.6(Opacity)	-	250	-
6.7(Fastness to Light)	-	10000	-
6.8(Durability Test for Exterior Use Only)	-	15000	-
Table 1, 6.10, 6.11 and 9.1(Consistency)	-	250	-
Table 1, 6.10, 6.11 and 9.2(Drying time,(a) Surface Dry, class A and B)	-	250	-
Table 1, 6.10, 6.11 and 9.3(Drying time,(a) Surface Dry, ass C and D)	-	250	-
Table 1, 6.10, 6.11 and 9.4(Drying time, Hard Dry, class A and B)	-	250	-
Table 1, 6.10, 6.11 and 9.5(Drying time, Hard Dry, ass C and D)	-	250	-
Table 1, 6.10, 6.11 and 9.6(Finish)	-	250	-
Table 1, 6.10, 6.11 and 9.7(Gloss at 60°, class A)	-	200	-
Table 1, 6.10, 6.11 and 9.8(Gloss at 60°, class B)	-	100	-
Table 1, 6.10, 6.11 and 9.9(Gloss at 60°, class C)	-	100	-
Table 1, 6.10, 6.11 and 9.10(Gloss at 60°, class D)	-	100	-
Table 1, 6.10, 6.11 and 9.11(Colour)	-	250	-
Table 1, 6.10, 6.11 and 9.12(Resistance to alkali)	-	250	-
Table 1, 6.10, 6.11 and 9.13(Washability and eanability)	-	500	-
Table 1, 6.10, 6.11 and 9.14(Accelerated storage stability)	-	250	-
Table 1, 6.10, 6.11 and 9.15(Recoating properties)	-	250	-
6.1(Composition)	-	250	-
6.2(Conditions in the Container)	-	250	-
6.3(Thinning)	-	250	-
6.4(Application Properties)	-	250	-
6.5(Mass in kg/10 litre)	-	250	-
6.6(Opacity)	-	250	-
6.7(Fastness to Light)	-	10000	-
6.8(Durability Test for Exterior Use Only)	-	15000	-
Table 1, 6.10, 6.11 and 9.1(Consistency)	-	250	-
Table 1, 6.10, 6.11 and 9.2(Drying time,(a) Surface Dry, class A and B)	-	250	-
Table 1, 6.10, 6.11 and 9.3(Drying time,(a) Surface Dry, ass C and D)	-	250	-
Table 1, 6.10, 6.11 and 9.4(Drying time, Hard Dry, class A and B)	-	250	-
Table 1, 6.10, 6.11 and 9.5(Drying time, Hard Dry, ass C and D)	-	250	-
Table 1, 6.10, 6.11 and 9.6(Finish)	-	250	-
Table 1, 6.10, 6.11 and 9.7(Gloss at 60°, class A)	-	250	-
Table 1, 6.10, 6.11 and 9.8(Gloss at 60°, class B)	-	250	-
Table 1, 6.10, 6.11 and 9.9(Gloss at 60°, class C)	-	250	-
Table 1, 6.10, 6.11 and 9.10(Gloss at 60°, class D)	-	250	-
Table 1, 6.10, 6.11 and 9.11(Colour)	-	250	-
Table 1, 6.10, 6.11 and 9.12(Resistance to alkali)	-	250	-
Table 1, 6.10, 6.11 and 9.13(Washability and eanability)	-	250	-
Table 1, 6.10, 6.11 and 9.14(Accelerated storage stability)	-	250	-
Table 1, 6.10, 6.11 and 9.15(Recoating properties)	-	250	-

08 Apr, 2027

-
-

IS 6419 (1996)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

18500 View breakup
Chemical Test of Wire/Weld Rs. 5,000/- each Mechanical Test Rs. Rs.15,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Diameter)	-	500	-
6(Reels for Wire)	-	500	-
7(Reeling Condition)	-	500	-
8(Dimension of Spools, Rims & Coils)	-	500	-
9(Lengthof Rods)	-	500	-
10.1(Finish)	-	500	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	1000	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	500	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	500	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	500	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	1000	-
14.2(Soundness test)	-	1000	-
14.3.2(UTS)	-	1000	-
14.3.2(Yield Stress)	-	1000	-
14.3.2(% of Elongation)	-	1000	-
14.3.3(Impact Test)	-	3000	-
5(Diameter)	-	-	-
6(Reels for Wire)	-	-	-
7(Reeling Condition)	-	-	-
8(Dimension of Spools, Rims & Coils)	-	-	-
9(Lengthof Rods)	-	-	-
10.1(Finish)	-	-	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	-	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	-	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	-	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	-	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	-	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	-	-
14.2(Soundness test)	-	-	-
14.3.2(UTS)	-	-	-
14.3.2(Yield Stress)	-	-	-
14.3.2(% of Elongation)	-	-	-
14.3.3(Impact Test)	-	-	-

08 Apr, 2027

-
Included w.e.f. 04.01.2024

IS 158 (2015)

Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Composition)	-	375	-
4.2.1(Lead Restriction)	-	1000	-
Cl 4.3, Table 1, S.no. i)(Drying time, Hard dry)	-	375	-
Cl 4.3, Table 1, S.no. ii)(Consistency)	-	375	-
Cl 4.3, Table 1, S.no. iii)(Finish)	-	375	-
Cl 4.3, Table 1, S.no. iv)(Wet opacity)	-	375	-
Cl 4.3, Table 1, S.no. v)(Colour)	-	375	-
Cl 4.3, Table 1, S.no. vi)( Mass)	-	375	-
Cl 4.3, Table 1, S.no. vii)(Water content)	-	375	-
Cl 4.3, Table 1, S.no.viii)(Flexibility and adhesion)	-	375	-
Cl 4.3, Table 1, S.no. ix)(Stripping test )	-	375	-
Cl 4.3, Table 1, S.no. x)(Protection against corrosion under conditions of condensation)	-	375	-
Cl 4.3, Table 1, S.no.xi)(Volatile matter, perce)	-	375	-
Cl 4.3, Table 1, S.no.xii)(Resistance to acid)	-	375	-
Cl 4.3, Table 1, S.no.xiii)(Resistance to alkali)	-	375	-
Cl 4.3, Table 1, S.no.xiv)(Resistance to Heat)	-	375	-
Cl 4.3, Table 1, S.no.xv)(Flash point ,)	-	375	-
Cl 4.3, Table 1, S.no.xvi) (Keeping properties)(IS 101 Part 6 Sec 2)	-	5000	-

08 Apr, 2027

-
-

IS 9862 (2017)

Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Lead restriction)	-	1000	-
4.3, Table-1(i)(Drying time,(a) Hard dry)	-	375	-
4.3, Table-1(ii)(Consistency)	-	375	-
4.3, Table-1(iii)(Finish)	-	375	-
4.3, Table-1(iv)(Wet opacity)	-	375	-
4.3, Table-1(v)(Mass)	-	375	-
4.3, Table-1(vi)(Colour)	-	375	-
4.3, Table-1(vii)(Flaxibility and adhesion ( Bend test of the film by 6.25 mm Mandrel type-1 apparatus)	-	375	-
4.3, Table-1(viii)(Stripping test)	-	375	-
4.3, Table-1(ix)(Flash point)	-	375	-
4.3, Table-1(x)(Volatile matter content)	-	375	-
4.3, Table-1(xi)(Resistance to humidity under conditions of condensation)	-	375	-
4.3, Table-1(xii)(Resistance to water)	-	375	-
4.3, Table-1(xiii)(Resistance to acid)	-	375	-
4.3, Table-1(xv)(Resistance to chlorine)	-	375	-
4.3, Table-1(xvi)(Water content (if water is suspected to be present))	-	375	-
4.3, Table-1(xvii)(Keeping properties)	-	5000	-
4.3, Table-1(xiv)(Resistance to alkali)	-	375	-

08 Apr, 2027

-
Included w.e.f. 04.01.2024

Bureau of Indian Standards

The National Standards Body of India

National Test House (NTH), Alipore, Kolkata-700027

11/1 Judges Court Road, Kolkata, Kolkata, Kolkata, West Bengal, 700027

9324565281 nthsal-wb@nic.in

Scope List