BIS - LIMS (Laboratory Information Management System)

Standard Testing Laboratory Private Limited

PLOT NO.782,KANJHAWALA INDUSTRIAL AREA,NEW DELHI,NORTH WEST, Delhi, North West, Delhi, 110081

9310136320 standardtestinglaboratory@yahoo.com

Scope List

Reset

77 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 15392 (2003)

Aluminium and aluminium alloy bare foil for food packaging - Specification

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 5 Table 1(PINHOLE COUNT)	-	9500	-
Clause 6(FREEDOM FROM DEFECTS)	-	9500	-
Clause 7 Sub-Clause 7.1(Material)	-	9500	-
Clause 7 Sub-Clause 7.2(Material)	-	9500	-
Clause 10 Table 2(Preferred Thickness)	-	9500	-
Clause 11(Average Thickness)	-	9500	-
Clause 14(Surface condition)	-	9500	-
Clause 12(Dimension and Tolerances: I) Width)	-	9500	-
Clause 12(Dimension and Tolerances: 2) Length)	-	9500	-
9(Lubricants)	-	9500	-
13-(Table-5)(Tensile properties-IS 13237)	-	9500	-
7(Copper- IS 504)	-	9500	-
7(Copper- IS 504)	-	9500	-
7(Magnesium-IS 504)	-	9500	-
7(Silicon- IS 504)	-	9500	-
7(Iron-IS 504)	-	9500	-
7(Manganese-IS 504)	-	9500	-
7(Zinc-IS 504)	-	9500	-
7(Titanium- IS 504)	-	9500	-
7(Chromium- IS 504)	-	9500	-
7(Cu+Si+Fe+Mn+Zn)	-	9500	-
7(Cu+Mg+Si+Pe+Mn+Zn)	-	9500	-
7(Cu+Mg+Si+Pe+Mn+Zn)	-	9500	-

10 Apr, 2028

-
Included w.e.f. 24.03.2026

IS 733 (2025)

Wrought Aluminium and Aluminium Alloy Bars, Rods, Sections, Extruded Tube, Hollow Sections and Profiles for General Engineering Purposes ? Specification (Fourth Revision)

All Grade

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 Table 1 - Table 8(Sodium)	-	6000	-
Cl. 6 Table 1 - Table 8(Strontium)	-	6000	-
Cl. 6 Table 1 - Table 8(Antimony)	-	6000	-
Cl. 6 Table 1 - Table 8(Phosphorus)	-	6000	-
Cl. 6 Table 1 - Table 8(Zirconium +Titanium)	-	6000	-
Cl-4(General requirements)	-	6000	-
Cl-6.1, Table-1 to 8(Fe)	-	6000	-
Cl-6.1, Table-1 to 8(Cu)	-	6000	-
Cl-6.1, Table-1 to 8(Mn)	-	6000	-
Cl-6.1, Table-1 to 8(Mg)	-	6000	-
Cl-6.1, Table-1 to 8(Cr)	-	6000	-
Cl-6.1, Table-1 to 8(Zn)	-	6000	-
Cl-6.1, Table-1 to 8(Ti)	-	6000	-
Cl-6.1, Table-1 to 8(V)	-	6000	-
Cl-6.1, Table-1 to 8(Aluminium)	-	6000	-
Cl-6.2(chemical analysis)	-	6000	-
Cl-7.1, 7.2 & 7.3, Table-9(Dimensions)	-	6000	-
Cl-7.1, 7.2 & 7.3, Table-9(Rm MPa)	-	6000	-
Cl-7.1, 7.2 & 7.3, Table-9(Rp0.2 MPa)	-	6000	-
Cl-7.1, 7.2 & 7.3, Table-9(Elongation , Percent)	-	6000	-
Cl-9(Dimensions and Tolerances)	-	6000	-
Cl-12(Packaging and Marking)	-	6000	-
Cl-7.1(Tensile test)	-	6000	-
Cl-5(Freedom from Defects)	-	6000	-
Cl-6.1, Table-1 to 8(Si)	-	6000	-

10 Apr, 2028

-
Included w.e.f. 24.03.2026

IS 10748 (2025)

Hot-Rolled Steel Strip for Welded Tubes and Pipes - Specification ( Third Revision)

All Grade

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of Materials)	-	12000	-
Cl-6(Manufacture)	-	12000	-
Cl-7.1(Ladle Analysis)	-	12000	-
Cl-7.2(Product Analysis)	-	12000	-
Cl-7.3(Carbon Equivalent Value)	-	12000	-
Cl-8.1(Number of Tensile Tests)	-	12000	-
Cl-8.2(Tensile Test Pieces)	-	12000	-
Cl-8.3(Tensile Test)	-	12000	-
Cl-8.3, Table-5 & 6(Tensile Strength, MPa)	-	12000	-
Cl-8.3, Table-5 & 6(Yield Strength, MPa)	-	12000	-
Cl-8.3, Table-5 & 6(Internal Diameter of Bend)	-	12000	-
Cl-9.1(Number of Bend Tests)	-	12000	-
Cl-9.2(Bend test)	-	12000	-
Cl-10(Re- Tests)	-	12000	-
Cl-11(freedam from Defects)	-	12000	-
Cl-12(Dimensions)	-	12000	-
Cl-13(Tolerances)	-	12000	-
Cl-14(Calculation of Mass)	-	12000	-
Cl-16(Marking)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Carbon)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Manganese)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Sulphur)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Phosphorus)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Carbon Equivalent Value (CEV))	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(silicon)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(aluminium)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(total aluminium)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Niobium)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Vanadium)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Titanium)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Nitrogen)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Copper)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Mo + Cr +W)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Mo)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Boron)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Nickel)	-	12000	-
Cl-7.1, 7.2, 7.3 & 7.4(Chromium)	-	12000	-
Cl-8.3, Table-5 & 6(Elongation at Gauge Length,)	-	12000	-

10 Apr, 2028

-
included w.e.f 09.03.2026

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking)	-	10000	-
4(Type)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Carbon Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Silicon Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Manganese Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nickel Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Chromium Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Sulphur Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Phouphorous Content)	-	10000	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nitrogen Content)	-	10000	-
6(Thickness of sheet/strip)	-	10000	-
6(Depth of bowl)	-	10000	-
6(Internal dimensions of the bowl)	-	10000	-
6(Bowl locating limits)	-	10000	-
6(Co-ordinating sizes)	-	10000	-
7.1(Consruction and workmanship)	-	10000	-
7.1.1(Consruction and workmanship)	-	10000	-
7.2(Consruction and workmanship)	-	10000	-
7.2.1(Consruction and workmanship)	-	10000	-
7.3(Drainers)	-	10000	-
7.4(Waste outlet)	-	10000	-
7.5(Tap holes)	-	10000	-
7.6(Overflows)	-	10000	-
8(Finish)	-	10000	-
5(MATERIALS)	-	10000	-
6.1.1(Thickness of Sheet/Strip)	-	10000	-
6.1.2(Thickness of Sheet/Strip)	-	10000	-
6.2(Depth of Bowls)	-	10000	-
6.3(Internal Dimensions of Bowls)	-	10000	-
6.4.1(Bowl Locating Limits)	-	10000	-
6.5(Coordinating Sizes)	-	10000	-
7.1(CONSTRUCTION AND WORKMANSHIP)	-	10000	-
7.1.1(CONSTRUCTION AND WORKMANSHIP)	-	10000	-
7.2.1(CONSTRUCTION AND WORKMANSHIP)	-	10000	-
7.3(CONSTRUCTION AND WORKMANSHIP)	-	10000	-
7.4(Waste Outlet)	-	10000	-
7.5(Tap Holes)	-	10000	-
7.6(OVERFLOW)	-	10000	-
Clause no. 4(types)	-	10000	-
Caluse no. 5("Material -Austenitic stainless steel of Grade Designation")	-	10000	-
Clause no. 6.1(Thickness of sheet)	-	10000	-
Clause no. 6.2(Depth of Bowls)	-	10000	-
Clause no. 6.3(Internal dimensions of bowls)	-	10000	-
Clause no. 6.4(Bowl Locating Limits)	-	10000	-
Clause no. 6.5, Table No. 1(Dimension of the sink)	-	10000	-
Clause no. 7(Construction and workmanship)	-	10000	-
Clause no. 8(Finish)	-	10000	-
Clause no. 9(Mark)	-	10000	-

10 Apr, 2028

-
Included w.e.f 06.01.2026

IS 12427 (2001)

Fasteners - Threaded steel fasteners - Hexagon head transmission tower bolts - Specification (First Revision)

All

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Designation)	-	22000	-
Cl 3.1, Cl 3.2, Fig-1, Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3.3, IS 4218(Pt 1 to 4) & IS 2334(Threads)	-	22000	-
Cl 5.1 & IS 14394(Nuts)	-	22000	-
Cl 5.2, IS 2016 & IS 4759(Washers)	-	22000	-
Cl 6.1 & IS 1367(Pt 3)(Bolt Tensile,Proof,Wedge Loading,Hardness Test)	-	22000	-
Cl 6.2(Bolt Shear Strength)	-	22000	-
Cl 7 & IS 1367(Pt 13)(Finish)	-	22000	-
Cl 8 & IS 1367(Pt 9/Sec1)(General Requirements)	-	22000	-
(Cl 8)(General Requirements)	-	22000	-
(Cl 7)(Finish)	-	22000	-
(Cl 7)(Finish)	-	22000	-
(Cl 6.2)(Shear Strength )	-	22000	-
(Cl 9.15)(Mechanical Properties)	-	22000	-
(Cl 9.14)(Mechanical Properties)	-	22000	-
(Cl 9.13)(Mechanical Properties)	-	22000	-
(Cl 9.12)(Mechanical Properties)	-	22000	-
(Cl 9.11)(Mechanical Properties)	-	22000	-
(Cl 9.10)(Mechanical Properties)	-	22000	-
(Cl 8.3)(Mechanical Properties)	-	22000	-
(Cl 9.9)(Mechanical Properties)	-	22000	-
(Cl 9.8)(Mechanical Properties)	-	22000	-
(Cl 9.7) (Mechanical Properties)	-	22000	-
(Cl 9.7) (Mechanical Properties)	-	22000	-
(Cl 9.7) (Mechanical Properties)	-	22000	-
(Cl 9.7) (Mechanical Properties)	-	22000	-
(Cl 9.6)(Mechanical Properties)	-	22000	-
(Cl 9.5)(Mechanical Properties)	-	22000	-
(Cl 9.4)(Mechanical Properties)	-	22000	-
(Cl 9.3)(Mechanical Properties)	-	22000	-
(Cl 9.3)(Mechanical Properties)	-	22000	-
(Cl 9.3)(Mechanical Properties)	-	22000	-
(Cl 9.2)(Mechanical Properties)	-	22000	-
(Cl 9.1)(Mechanical Properties)	-	22000	-
Cl 6.1 & IS 1367(Pt 3)(Mechanical Properties)	-	22000	-
(Cl 5)(Matching Nuts & Washers)	-	22000	-
(Cl 5)(Matching Nuts & Washers)	-	22000	-
(Cl 3.3)(Threads)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 3 Table-1 & Table-2(Dimensions)	-	22000	-
Cl 9(Designation)	-	22000	-

10 Apr, 2028

-
Included w.e.f 06.01.2026

IS 1364 : Part 2 (2023)

Hexagon head bolts screws and nuts of product grades A and B Part 2 Hexagon head screws (Size range M1.6 to M64 ) (Sixth revision of IS 1364 (Part 2))

M1.6 to M39

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Dimensions)	-	14000	-
Cl-5, Table-5(General requirements)	-	14000	-
Cl-5, Table-5(Thread-Tolerance class)	-	14000	-
Cl-5, Table-5(Mechanical properties-Steel)	-	14000	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	14000	-
Cl-5, Table-5(Tolerances- Product grade)	-	14000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	14000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	14000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	14000	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	14000	-
Cl-6(Marking)	-	14000	-
Cl-4(Dimensions)	-	14000	-
Cl-5, Table-5(General requirements)	-	14000	-
Cl-5, Table-5(Thread-Tolerance class)	-	14000	-
Cl-5, Table-5(Mechanical properties-Steel)	-	14000	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	14000	-
Cl-5, Table-5(Tolerances- Product grade)	-	14000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	14000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	14000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	14000	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	14000	-
Cl-6(Marking)	-	14000	-
Cl-4(Dimensions)	-	14000	-
Cl-5, Table-5(General requirements)	-	14000	-
Cl-5, Table-5(Thread-Tolerance class)	-	14000	-
Cl-5, Table-5(Mechanical properties-Steel)	-	14000	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	14000	-
Cl-5, Table-5(Tolerances- Product grade)	-	14000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	14000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	14000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	14000	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	14000	-
Cl-6(Marking)	-	14000	-

10 Apr, 2028

-
Included w.e.f 24.02.2026

IS 1364 : Part 1 (2023)

Hexagon head bolts, screws, and nuts of property grades A and B: Part 1 Hexagon head bolts (Size range M1.6 to M64) (sixth revision)

M1.6 to M39

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Dimensions)	-	13000	-
Cl-5, Table-7(General requirements)	-	13000	-
Cl-5, Table-7(Thread-Tolerance class)	-	13000	-
Cl-5, Table-7(Mechanical properties- Steel)	-	13000	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	13000	-
Cl-5, Table-7(Tolerances-Product grade)	-	13000	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	13000	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	13000	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	13000	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	13000	-
Cl-6(Marking)	-	13000	-
Cl-4(Dimensions)	-	13000	-
Cl-5, Table-7(General requirements)	-	13000	-
Cl-5, Table-7(Thread-Tolerance class)	-	13000	-
Cl-5, Table-7(Mechanical properties- Steel)	-	13000	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	13000	-
Cl-5, Table-7(Tolerances-Product grade)	-	13000	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	13000	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	13000	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	13000	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	13000	-
Cl-6(Marking)	-	13000	-
Cl-4(Dimensions)	-	13000	-
Cl-5, Table-7(General requirements)	-	13000	-
Cl-5, Table-7(Thread-Tolerance class)	-	13000	-
Cl-5, Table-7(Mechanical properties- Steel)	-	13000	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	13000	-
Cl-5, Table-7(Tolerances-Product grade)	-	13000	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	13000	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	13000	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	13000	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	13000	-
Cl-6(Marking)	-	13000	-

10 Apr, 2028

-
Included w.e.f 24.02.2026

IS 1363 : Part 2 (2023)

Hexagon head bolts, screws and nuts of product grade C Part 2 Hexagon head screws (Size range M5 to M64) (sixth revision)

All

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	14000	-
5- Table 4 -(i)(General requirements)	-	14000	-
5- Table 4 -(ii)(Thread)	-	14000	-
5- Table 4 -(iii)(Mechanical properties)	-	14000	-
5- Table 4 -(iv)(Tolerances)	-	14000	-
5- Table 4 -(v)(Surface condition)	-	14000	-
5- Table 4 -(vi)(Surface integrity)	-	14000	-
5- Table 4 -(vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-
4(Finish -Electrolite zinc coating)	-	14000	-
4(Dimensions)	-	14000	-
5- Table 4 -(i)(General requirements)	-	14000	-
5- Table 4 -(ii)(Thread)	-	14000	-
5- Table 4 -(iii)(Mechanical properties)	-	14000	-
5- Table 4 -(iv)(Tolerances)	-	14000	-
5- Table 4 -(v)(Surface condition)	-	14000	-
5- Table 4 -(vi)(Surface integrity)	-	14000	-
5- Table 4 -(vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-
4(Finish -Electrolite zinc coating)	-	14000	-
4(Dimensions)	-	14000	-
5- Table 4 -(i)(General requirements)	-	14000	-
5- Table 4 -(ii)(Thread)	-	14000	-
5- Table 4 -(iii)(Mechanical properties)	-	14000	-
5- Table 4 -(iv)(Tolerances)	-	14000	-
5- Table 4 -(v)(Surface condition)	-	14000	-
5- Table 4 -(vi)(Surface integrity)	-	14000	-
5- Table 4 -(vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-
4(Finish -Electrolite zinc coating)	-	14000	-

10 Apr, 2028

-
Included w.e.f 24.02.2026

IS 1363 : Part 1 (2023)

Hexagon head bolts, screws and nuts of product grade C Part 1 Hexagon head bolts (Size range M5 to M64) (sixth revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	14000	-
5 - Table 5 (i)(General requirements)	-	14000	-
5 - Table 5 (ii)(Thread)	-	14000	-
5 - Table 5 (iii)(Mechanical properties)	-	14000	-
5 - Table 5 (iv)(Tolerances)	-	14000	-
5 - Table 5 (v)(Surface condition)	-	14000	-
5 - Table 5 (vi)(Surface integrity)	-	14000	-
5 - Table 5 (vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-
4(Dimensions)	-	14000	-
5 - Table 5 (i)(General requirements)	-	14000	-
5 - Table 5 (ii)(Thread)	-	14000	-
5 - Table 5 (iii)(Mechanical properties)	-	14000	-
5 - Table 5 (iv)(Tolerances)	-	14000	-
5 - Table 5 (v)(Surface condition)	-	14000	-
5 - Table 5 (vi)(Surface integrity)	-	14000	-
5 - Table 5 (vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-
4(Dimensions)	-	14000	-
5 - Table 5 (i)(General requirements)	-	14000	-
5 - Table 5 (ii)(Thread)	-	14000	-
5 - Table 5 (iii)(Mechanical properties)	-	14000	-
5 - Table 5 (iv)(Tolerances)	-	14000	-
5 - Table 5 (v)(Surface condition)	-	14000	-
5 - Table 5 (vi)(Surface integrity)	-	14000	-
5 - Table 5 (vii)(Acceptability)	-	14000	-
6(Marking and labelling)	-	14000	-
7(Designation)	-	14000	-

10 Apr, 2028

-
Included w.e.f 24.02.2026

IS 10238 (2001)

Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification (First Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GRADES)	-	12500	-
5(MECHANICAL PROPERTIES)	-	12500	-
6-6.1(Nuts)	-	12500	-
6-6.2.1(Washers)	-	12500	-
6-.6.2.2(Washers)	-	12500	-
7(GENERAL REQUIREMENTS)	-	12500	-
8.1(FINISH)	-	12500	-
8.2()	-	12500	-
8.3()	-	12500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	12500	-
10.1.1(TESTS)	-	12500	-
12(MARKING)	-	12500	-
13(PACKAGING)	-	12500	-
Table 3 (i)(Tensile strength, Rm, MPa)	-	12500	-
Table 3 (ii)(Lower yield strength)	-	12500	-
Table 3 (iii)(Stress at 0,2 % non-proportional elongation)	-	12500	-
table 3 (iv)(Stress at 0,0048d non-proportional elongation for full-size fasteners)	-	12500	-
Table 3 (v)((i) Stress under proof load (ii) Proof strength ratio)	-	12500	-
Table (vi)(Percentage elongation after fracture for machined test pieces)	-	12500	-
Table 3 (vii)(Percentage reduction of area after fracture for machined test pieces,)	-	12500	-
Table 3 (viii)(Elongation after fracture for full-size fasteners,)	-	12500	-
Table 3 (ix)(Head soundness)	-	12500	-
Table 3 (x)(Vickers hardness)	-	12500	-
table 3 (xi)(Brinell hardness)	-	12500	-
table 3()	-	12500	-
table 3 (xii)(Rockwell hardness, HRB Rockwell hardness, HRC)	-	12500	-
Table 3 (xiv)(Surface hardness)	-	12500	-
Table 3 (xv)(Height of non-decarburized thread zone,)	-	12500	-
Table 3 (xv)(Height of non-decarburized thread zone, Depth of complete decarburization in the thread,)	-	12500	-
table 3 (xvi)(Reduction of hardness after retempering HV)	-	12500	-
table 3 (xvii)(Breaking torque)	-	12500	-
table 3 (xviii)(Impact strength, KV)	-	12500	-
Table3 (xix)(Surface integrity in accordance with)	-	12500	-
table 3 (xvii)(Breaking torque Nm)	-	12500	-
3(DIMENSIONS AND TOLERANCES)	-	12500	-
CL 3(Dimensions and Tolerances)	-	12500	-
CL 8(Finish)	-	12500	-
5(Torsion test)	-	12500	-
Clause 3(Thread Requirements)	-	12500	-
Clause 11(Designation)	-	12500	-
Clause 13(Packaging)	-	12500	-
4(GRADES)	-	12500	-
5(MECHANICAL PROPERTIES)	-	12500	-
6-6.1(Nuts)	-	12500	-
6-6.2.1(Washers)	-	12500	-
6-.6.2.2(Washers)	-	12500	-
7(GENERAL REQUIREMENTS)	-	12500	-
8.1(FINISH)	-	12500	-
8.2()	-	12500	-
8.3()	-	12500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	12500	-
10.1.1(TESTS)	-	12500	-
12(MARKING)	-	12500	-
13(PACKAGING)	-	12500	-
Table 3 (i)(Tensile strength, Rm, MPa)	-	12500	-
Table 3 (ii)(Lower yield strength)	-	12500	-
Table 3 (iii)(Stress at 0,2 % non-proportional elongation)	-	12500	-
table 3 (iv)(Stress at 0,0048d non-proportional elongation for full-size fasteners)	-	12500	-
Table 3 (v)((i) Stress under proof load (ii) Proof strength ratio)	-	12500	-
Table (vi)(Percentage elongation after fracture for machined test pieces)	-	12500	-
Table 3 (vii)(Percentage reduction of area after fracture for machined test pieces,)	-	12500	-
Table 3 (viii)(Elongation after fracture for full-size fasteners,)	-	12500	-
Table 3 (ix)(Head soundness)	-	12500	-
Table 3 (x)(Vickers hardness)	-	12500	-
table 3 (xi)(Brinell hardness)	-	12500	-
table 3()	-	12500	-
table 3 (xii)(Rockwell hardness, HRB Rockwell hardness, HRC)	-	12500	-
Table 3 (xiv)(Surface hardness)	-	12500	-
Table 3 (xv)(Height of non-decarburized thread zone,)	-	12500	-
Table 3 (xv)(Height of non-decarburized thread zone, Depth of complete decarburization in the thread,)	-	12500	-
table 3 (xvi)(Reduction of hardness after retempering HV)	-	12500	-
table 3 (xvii)(Breaking torque)	-	12500	-
table 3 (xviii)(Impact strength, KV)	-	12500	-
Table3 (xix)(Surface integrity in accordance with)	-	12500	-
table 3 (xvii)(Breaking torque Nm)	-	12500	-
3(DIMENSIONS AND TOLERANCES)	-	12500	-
CL 3(Dimensions and Tolerances)	-	12500	-
CL 8(Finish)	-	12500	-
5(Torsion test)	-	12500	-
Clause 3(Thread Requirements)	-	12500	-
Clause 11(Designation)	-	12500	-
Clause 13(Packaging)	-	12500	-

10 Apr, 2028

-
Included w.e.f 09.02.2026

IS 617 (2024)

Aluminium and Aluminium Alloys Ingots for Remelting and Castings for General Engineering Purposes â Specification (Fourth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1, Table-1(Si)	-	12000	-
Cl-6.1, Table-1(Fe)	-	12000	-
Cl-6.1, Table-1(Cu)	-	12000	-
Cl-6.1, Table-1(Mn)	-	12000	-
Cl-6.1, Table-1(Mg)	-	12000	-
Cl-6.1, Table-1(Cr)	-	12000	-
Cl-6.1, Table-1(Ni)	-	12000	-
Cl-6.1, Table-1(Zn)	-	12000	-
Cl-6.1, Table-1(Pb)	-	12000	-
Cl-6.1, Table-1(Sn)	-	12000	-
Cl-6.1, Table-1(Ti)	-	12000	-
Cl-6.1, Table-1(Others elements Each)	-	12000	-
Cl-6.1, Table-1(Others elements Total)	-	12000	-
Cl-6.1, Table-1(Aluminium)	-	12000	-
Cl-6.2(The chemical analysis)	-	12000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Tensile Strength)	-	12000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Proof Stress)	-	12000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Elongation)	-	12000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Brinell Hardness HBW)	-	12000	-
Cl-7.1, Table-3(Chill Cast Alloys- Tensile Strength)	-	12000	-
Cl-7.1, Table-3(Chill Cast Alloys- Proof Stress)	-	12000	-
Cl-7.1, Table-3(Chill Cast Alloys- Elongation)	-	12000	-
Cl-7.1, Table-3(Chill Cast Alloys- Brinell Hardness HBW)	-	12000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Tensile Strength)	-	12000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Proof Stress)	-	12000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Elongation)	-	12000	-
Cl-7.1, Table-4(Investment-Cast Alloys-Brinell Hardness)	-	12000	-
Cl-7.2(Tensile Tests)	-	12000	-
Cl-7.3(Test Pieces)	-	12000	-
Cl-7.4(Hardness)	-	12000	-
Cl-8(Freedom from Defects)	-	12000	-
Cl-11(RETEST)	-	12000	-
Cl-13(Marking)	-	12000	-
Cl. 6(Silicon)	-	12000	-
Cl. 6(Iron)	-	12000	-
Cl. 6(Copper)	-	12000	-
Cl. 6(Manganese)	-	12000	-
Cl. 6(Magnesium)	-	12000	-
Cl. 6(Chromium)	-	12000	-
Cl. 6(Nickel)	-	12000	-
Cl. 6(Zinc)	-	12000	-
Cl. 6(Lead)	-	12000	-
Cl. 6(Tin)	-	12000	-
Cl. 6(Titanium)	-	12000	-
Cl. 6(Others Element Each)	-	12000	-
Cl. 6(Others Element Total)	-	12000	-
Cl. 6(Aluminium)	-	12000	-
Cl. 6(Silver)	-	12000	-
Cl. 6(Zirconium)	-	12000	-
Cl. 6(Titanium+Zirconium)	-	12000	-
Cl. 6(Antimony)	-	12000	-
Cl. 6(Cobalt)	-	12000	-
Cl. 6(Antimony+Cobalt)	-	12000	-
Cl. 6(Beryllium)	-	12000	-
10(Pressure Test)	-	12000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	13000	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	13000	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	13000	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	13000	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	13000	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	13000	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	13000	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	13000	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	13000	-
6.2.2(Fittings)	-	13000	-
6.3(General)	-	13000	-
6.3(General)	-	13000	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	13000	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	13000	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	13000	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	13000	-
8.2.2(Regulated Emitting Pipes)	-	13000	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	13000	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	13000	-
8.3.3(Flow Paths in Emitting Unit)	-	13000	-
8.3.4(Spacing ofEmitter Units)	-	13000	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	13000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	13000	-
8.5(Resistance to Tension at Elevated Temperature)	-	13000	-
8.5(Resistance to Tension at Elevated Temperature)	-	13000	-
8.5(Resistance to Tension at Elevated Temperature)	-	13000	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	13000	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	13000	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	13000	-
8.8(Determination of Emitting Unit Exponent)	-	13000	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	13000	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	13000	-
4.1 a(Identification)	-	13000	-
4.1 a(Identification)	-	13000	-
4.1 c(Volatile matter Extract)	-	13000	-
4.1 d(Density)	-	13000	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	13000	-
4.2(Carbon black content)	-	13000	-
4.2(Carbon black dispersion)	-	13000	-
5.1(Materials)	-	13000	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	13000	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	13000	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	13000	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	13000	-
6.2(Fittings)	-	13000	-
6.3(General)	-	13000	-
7.1(Test Specimens)	-	13000	-
7.2(Order of Tests)	-	13000	-
7.3(Testing Conditions)	-	13000	-
7.4(Accuracy of Measuring Devices)	-	13000	-
8.1(Uniformity of Emission Rate)	-	13000	-
8.1.2(Unregulated Emitting Pipes)	-	13000	-
8.1.3(Regulated Emitting Pipes)	-	13000	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	13000	-
8.2.1(Unregulated Emitting Pipes)	-	13000	-
8.2.2(Regulated Emitting Pipes)	-	13000	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	13000	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	13000	-
8.3.3(Flow Paths in Emitting Unit)	-	13000	-
8.3.4(Spacing of Emitter Units)	-	13000	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	13000	-
8.5(Resistance to Tension at Elevated Temperature)	-	13000	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	13000	-
8.7.1(Acceptance Test)	-	13000	-
8.7.2(Type Test)	-	13000	-
8.8(Determination of Emitting Unit Exponen)	-	13000	-
9.1(Non-regulated Emitting Pipe)	-	13000	-
9.2(Regulated Emitting Pipe)	-	13000	-
10.1(Marking)	-	13000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

All

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	17000	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	17000	-
11(Transverse Tension Test,%)	-	17000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	17000	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	17000	-
14(Reverse Flattaning Test)	-	17000	-
15(Flattaning Test-IS 2328)	-	17000	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	17000	-
18(Leak Tighteness Test)	-	17000	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	17000	-
20(Eddy current test, Air under water test ,Radiographic tests)	-	0	-
22(Workmanship, Finish and Appearance)	-	17000	-
23(Repair by Welding or Grinding)	-	17000	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	17000	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	17000	-
Clause 10.1 - Table 4(Tensile Strength)	-	17000	-
Clause 10.1 - Table 4(Yield Strength)	-	17000	-
Clause 10.1 - Table 4(Percent Elongation)	-	17000	-
Clause 11(Transverse Tension Test)	-	17000	-
Clause 12(Hardness Test)	-	17000	-
Clause 13(Flange Test)	-	17000	-
Clause 14(Reverse Flattening Test)	-	17000	-
Clause 15(Flattening Test)	-	17000	-
Clause 16(Grain Size)	-	17000	-
Clause 18()	-	17000	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	17000	-
Clause 22(Workmanship, Finish & Appearance)	-	17000	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	17000	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	17000	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	17000	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	0	-
12.2(Hardness test)	-	17000	-
17(Sampling)	-	17000	-
25(Marking)	-	17000	-
6.7, Table 7, ii)(c) Chromium VI)	-	17000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025 Exclusion: Cl 20 (Eddy current test, Air under water test ,Radiographic tests) , Cl 8.1 & 8.2 (Table No.- 1) (Tantalum (Ta))

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

All

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	17000	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	17000	-
11(Transverse Tension Test,%)	-	17000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	17000	-
13 (Table No.- 7)(Flaring Test)	-	17000	-
14(Flattaning Test-IS 2328)	-	17000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	17000	-
17(Leak Tighteness Test)	-	17000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	17000	-
19(Eddy current test & Air under water)	-	0	-
21(Workmanship, Finish and Appearance)	-	17000	-
22(Repair by Welding or Grinding)	-	17000	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	17000	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	17000	-
Clause 10.1 - Table 4(Tensile Strength)	-	17000	-
Clause 10.1 - Table 4(Percent Elongation)	-	17000	-
Clause 11(Transverse Tension Test)	-	17000	-
Clause 12(Hardness Test)	-	17000	-
Clause 13(Flaring Test)	-	17000	-
Clause 14(Flattening Test)	-	17000	-
Clause 15(Grain Size)	-	17000	-
Clause 17(Leak Tightness Test)	-	17000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	17000	-
Clause 21(Workmanship, Finish & Appearance)	-	17000	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	17000	-
10.2(Hardness test IS 1500 (part-1):2019)	-	17000	-
12.2(Flaring test IS 17878:2022)	-	17000	-
16(Sampling)	-	17000	-
24(Marking)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	17000	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	0	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	17000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025 Exclusion: Cl 19 (Eddy current test & Air under water) , "Clause 8.1 and 8.2 - Table 1" (Ta)

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

All Grade / Type / Size / Designation

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	14000	-
4.1(General - IS 4246 : 2025)	-	14000	-
4.1.1(General - IS 4246 : 2025)	-	14000	-
5(Materials - Cl. 5 of IS 5116)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1.1(Materials - Toughened glass, if provided,)	-	14000	-
5.1(Materials - IS 5116)	-	14000	-
5.1(Materials - IS 5116)	-	14000	-
5.1.1(Materials - IS 5116)	-	14000	-
5.1.1(Materials - IS 5116)	-	14000	-
5.2(Materials - IS 5116)	-	14000	-
5.2(Materials - IS 5116)	-	14000	-
5.3(Materials - IS 5116)	-	14000	-
5.5(Materials - IS 5116)	-	14000	-
5.5(Materials - IS 5116)	-	14000	-
5.5(Materials - IS 5116)	-	14000	-
5.7(Materials - IS 5116)	-	14000	-
6.1(Design for Maintainance)	-	14000	-
6.1(Design for Maintainance)	-	14000	-
6.2(Design for Maintainance)	-	14000	-
6.2(Design for Maintainance)	-	14000	-
6.3(Design for Maintainance)	-	14000	-
6.4(Design for Maintainance)	-	14000	-
6.5(Design for Maintainance)	-	14000	-
6.6(Design for Maintainance)	-	14000	-
7.0(Rigidity and Stability)	-	14000	-
7.1(Rigidity and Stability)	-	14000	-
7.2(Rigidity and Stability)	-	14000	-
7.3(Rigidity and Stability)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	14000	-
8.2(Workmanship and Finish -)	-	14000	-
8.3(Workmanship and Finish -)	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	14000	-
10(Injector Jets)	-	14000	-
10(Injector Jets)	-	14000	-
10(Injector Jets)	-	14000	-
10(Injector Jets)	-	14000	-
10(Injector Jets)	-	14000	-
10(Injector Jets)	-	14000	-
11.1(Burners- Cl. 10 of IS 5116)	-	14000	-
11.1(Burners- Cl. 10 of IS 5116)	-	14000	-
11.1(Burners- Cl. 10 of IS 5116)	-	14000	-
11.1(Burners- Cl. 10 of IS 5116)	-	14000	-
11.1(Burners- Cl. 10 of IS 5116)	-	14000	-
11.2(Burners)	-	14000	-
11.3(Burners)	-	14000	-
11.4(Burners)	-	14000	-
12.1(Burner Pan Support)	-	14000	-
12.2(Burner Pan Support)	-	14000	-
12.3(Burner Pan Support)	-	14000	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	14000	-
13,2(Gas Soundness Test)	-	14000	-
13.2(Gas Leak Detector)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	14000	-
14.2(Gas Inlet Connection)	-	14000	-
14.2(Gas Inlet Connection)	-	14000	-
14.2(Gas Inlet Connection)	-	14000	-
14.2(Gas Inlet Connection)	-	14000	-
14.3(Gas Inlet Connection)	-	14000	-
14.4(Gas Inlet Connection)	-	14000	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	14000	-
14.6(Gas Inlet Connection)	-	14000	-
15.0(Strength and Rigidity)	-	14000	-
15.0(Strength and Rigidity)	-	14000	-
15.0(Strength and Rigidity)	-	14000	-
15.0(Strength and Rigidity)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.0(Gas Consumption Test)	-	14000	-
17.2(Gas Consumption Test - For Gas Stoves)	-	14000	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	14000	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	14000	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	14000	-
17.3(Gas Consumption Test - For Built in Hobs)	-	14000	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	14000	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	14000	-
18.1(Ignition and Flame Travel)	-	14000	-
18.1(Ignition and Flame Travel)	-	14000	-
18.2(Ignition and Flame Travel)	-	14000	-
18.3(Ignition and Flame Travel)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	14000	-
19.1(Flame Stability)	-	14000	-
19.1.1(Flame Stability)	-	14000	-
19.2(Flame Stability)	-	14000	-
19.3(Flame Stability)	-	14000	-
20(Noise Control)	-	14000	-
21(Flash Back)	-	14000	-
22(Formation of Soot)	-	14000	-
23(Resistance to Draught)	-	14000	-
24.1(Combustion)	-	14000	-
24.1(Combustion)	-	14000	-
24.2(Combustion)	-	14000	-
25.1(Fire Hazard and Limiting Temperatures)	-	14000	-
25.1(Fire Hazard and Limiting Temperatures)	-	14000	-
25.1(Fire Hazard and Limiting Temperatures)	-	14000	-
25.1(Fire Hazard and Limiting Temperatures)	-	14000	-
25.2(Fire Hazard and Limiting Temperatures)	-	14000	-
26.1(Thermal Efficiency- Gas Stoves)	-	14000	-
26.1(Thermal Efficiency- Gas Stoves)	-	14000	-
26.1(Thermal Efficiency- Gas Stoves)	-	14000	-
26.1(Thermal Efficiency- Gas Stoves)	-	14000	-
26.1(Thermal Efficiency- Gas Stoves)	-	14000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	14000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	14000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	14000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	14000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	14000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	13000	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	13000	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	13000	-
Cl-6.0(Visual Appearance)	-	13000	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	13000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	13000	-
Cl-7.2(Reversion Test)	-	13000	-
Cl-7.3(Tensile Test)	-	13000	-
Cl-7.3.1(Test Piece)	-	13000	-
Cl-7.3.2(Procedure)	-	13000	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	13000	-
Cl-8.0(Supply of pipes)	-	13000	-
Cl-9.0(Coiling)	-	13000	-
Cl-10.0(Sampling and criteria for conformity)	-	13000	-
Cl-11(Marking)	-	13000	-
3(Class of Pipe)	-	13000	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	13000	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	13000	-
6(Visual Appearance)	-	13000	-
7.1 & Table 2(Hydraulic Characteristics)	-	13000	-
7.1 & Table 2(Hydraulic Characteristics)	-	13000	-
7.2(Reversion Test)	-	13000	-
7.3(Tensile Strength)	-	13000	-
7.3(Elongation at Break)	-	13000	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	13000	-
4.2(a)(Carbon Black Content-IS 2530)	-	13000	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	13000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Gross capacity)	-	24000	-
4.2(Body Capacity)	-	24000	-
5.1(Body, Lid, Containers and Grid)	-	24000	-
5.1.2(Body and Lid )	-	24000	-
5.1.3(Stainless steel pressure cooker)	-	24000	-
5.1.4(Aluminium cooker )	-	24000	-
5.2(Safety Relief Device)	-	24000	-
5.3(Gasket)	-	24000	-
5.4(Handles and Knobs)	-	24000	-
5.5(Pressure Regulating Device )	-	24000	-
5.6(Vent Seal Pin for Pressure Regulating Device )	-	24000	-
5.7(Vent Pipe )	-	24000	-
5.8(Vent Pipe Nut )	-	24000	-
5.9(Spring )	-	24000	-
5.1(Material of Rim )	-	24000	-
5.11(Visual Pressure Indicator)	-	24000	-
5.12(Gasket Release System)	-	24000	-
6(Construction)	-	24000	-
7(Workmanship and Finish )	-	24000	-
8.1(Air Pressure Test )	-	24000	-
8.2(Proof Pressure Test )	-	24000	-
8.3(Operating Test for Pressure Regulating Device )	-	24000	-
8.4(Test for Safety Relief Device )	-	24000	-
8.5(Bursting Pressure Test )	-	24000	-
8.6(Test for Removal of Lid under Pressure )	-	24000	-
8.7(Test for Spring Loaded Mechanism )	-	24000	-
8.8(Composite Cooker Base )	-	24000	-
8.9(Aluminium induction compatible Base )	-	24000	-
8.1(Handles of cooker )	-	24000	-
8.11(External Coating)	-	24000	-
8.12(Internal Coating )	-	24000	-
8.13(Integral electrical heating)	-	24000	-
8.14(Ply construction cooker Body )	-	24000	-
8.15.1(Fragmentation Test )	-	24000	-
8.15.2(Ball Drop Test )	-	24000	-
8.15.3(Thermal Shock Test )	-	24000	-
8.15.4(Free Fall Test)	-	24000	-
8.17(Test for Effectiveness for Induction Bottom)	-	24000	-
11(Marking )	-	24000	-
12(Packing )	-	24000	-
4(Capacity)	-	24000	-
4.2(Body Capacity)	-	24000	-
5.1.1(Body, Lid, Containers and Grid)	-	24000	-
5.1.2(Body, Lid, Containers and Grid)	-	24000	-
5.1.3(Body, Lid, Containers and Grid)	-	24000	-
5.1.4(Body, Lid, Containers and Grid)	-	24000	-
5.1.5(Body, Lid, Containers and Grid)	-	24000	-
5.2.1(Destructive Type Safety Relief Device)	-	24000	-
5.2.2(Resettable Type Safety Relief Device)	-	24000	-
5.3(Gasket)	-	24000	-
5.4(Handles and Knobs)	-	24000	-
5.5(Pressure Regulating Device)	-	24000	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	24000	-
5.7(Vent Pipe)	-	24000	-
5.8(Vent Pipe Nut)	-	24000	-
5.9(Spring)	-	24000	-
5.10(Spring)	-	24000	-
5.11(Visual Pressure Indicator)	-	24000	-
5.12(Gasket Release System)	-	24000	-
6(CONSTRUCTION)	-	24000	-
6.1(Pressure Regulating Device)	-	24000	-
6.1.1(Pressure Regulating Device)	-	24000	-
6.1.1(Minimum Inside diameter of Vent Pipe.)	-	24000	-
6.1.2(Pressure Regulating Device)	-	24000	-
6.1.3(Pressure Regulating Device)	-	24000	-
6.1.4(Pressure Regulating Device)	-	24000	-
6.1.5(Pressure Regulating Device)	-	24000	-
6.1.6(Pressure Regulating Device)	-	24000	-
6.2(Safety Relief Device)	-	24000	-
6.2.1(Safety Relief Device)	-	24000	-
6.2.2(Safety Relief Device)	-	24000	-
6.2.3(Safety Relief Device)	-	24000	-
6.3.1(Temperature Responsive Safety Relief Device)	-	24000	-
6.3.2(Temperature Responsive Safety Relief Device)	-	24000	-
6.3.3(Temperature Responsive Safety Relief Device)	-	24000	-
6.4.1(Handles and Knobs)	-	24000	-
6.4.1.1(Handles and Knobs)	-	24000	-
6.4.2(Handles and Knobs)	-	24000	-
6.4.2.1(Handles and Knobs)	-	24000	-
6.5(CONSTRUCTION)	-	24000	-
6.6(CONSTRUCTION)	-	24000	-
6.7(Internal Level Marking)	-	24000	-
6.8(Internal Level Marking)	-	24000	-
7.1(WORKMANSHIP AND FINISH)	-	24000	-
7.2(WORKMANSHIP AND FINISH)	-	24000	-
8.17(Test for Effectiveness for Induction Bottom)	-	24000	-
8.16(PRD with chain)	-	24000	-
8.15.4.2(Glass lid without rim)	-	24000	-
8.15.4.1("Free Fall Test ( Glass lid with rim) ")	-	24000	-
8.15.3(Thermal Shock Test on Tempered Glass lid)	-	24000	-
8.15.2(Ball Drop Test on Tempered Glass lid)	-	24000	-
8.15.1(Fragmentation Test on Tempered Glass lid)	-	24000	-
8.14(3 ply construction cooker body)	-	24000	-
8.13(Pressure cooker with integral electrical heating)	-	24000	-
8.12(Internal Coating)	-	24000	-
7.3(WORKMANSHIP AND FINISH)	-	24000	-
7.4(WORKMANSHIP AND FINISH)	-	24000	-
8.1(Air Pressure Test)	-	24000	-
8.2(Proof Pressure Test)	-	24000	-
8.3.1(Operating Test for Pressure Regulating Device)	-	24000	-
8.4.1(Test for Safety Relief Device)	-	24000	-
8.4.2(Test for Safety Relief Device)	-	24000	-
8.4.2 NOTE(Test for Safety Relief Device)	-	24000	-
8.5(Bursting Pressure Test)	-	24000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	24000	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	24000	-
8.6.3(Tests for Removal of Lid under Pressure: For Cooker Fastened by Screw Clamps or Any Other Locking Device)	-	24000	-
8.6.4(Tests for Removal of Lid under Pressure in case of electrical pressure cooker)	-	24000	-
8.7(Test for Spring Loaded Mechanism)	-	24000	-
8.8(Test for stainless steel cookers)	-	24000	-
8.9("For stainless steel, aluminium induction compatible base and 3 ply cooker")	-	24000	-
8.10(Testing of Handles of the cooker)	-	24000	-
8.10 Note 3(Testing of Handles of the cooker)	-	24000	-
8.10 Note 4(Testing of Handles of the cooker)	-	24000	-
8.10 Note 5(Testing of Handles of the cooker)	-	24000	-
8.10 Note 6(Testing of Handles of the cooker)	-	24000	-
8.10.1(Testing of Handles of the cooker)	-	24000	-
8.11.1(External Coating)	-	24000	-

10 Apr, 2028

-
Included w.e.f. 15.10.2025 Exclusion: "6.5 (CONSTRUCTION) 8.10.1 (Testing of Handles of the cooker) 8.13 (Pressure cooker with integral electrical heating) 8.6.4 (Tests for Removal of Lid under Pressure in case of electrical pressure cooker) "

IS 18256 (2023)

Solid Round Glass Fibre Reinforced Polymer (GFRP) Bars for Concrete Reinforcement - Specification

All except Cl 5.2,5.3,6.4,6.6,6.7,7.3,8.2.4

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(clause 5.1)(Fibre content (mass fraction))	-	18000	-
(clause 5.2)(Glass transition temperature)	-	0	-
(clause 5.3)(Degree of Cure)	-	0	-
(clause 5.4.2)(Measured cross sectional area)	-	18000	-
(Table 1)("Minimum bend radius in case of bent bars")	-	18000	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	18000	-
(clause 6.2)(Tensile modulus of elasticity)	-	18000	-
(clause 6.3)(Ultimate Tensile Strain)	-	18000	-
(clause 6.4)(Transverse shear strength)	-	0	-
(clause 6.5)(Bond Strength)	-	18000	Additional 6000 for Bond Strength
(clause 6.6)(Fatigue Tensile Strength)	-	0	-
(clause 6.7)(Creep Failure)	-	0	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	18000	-
(clause 7.2)(Resistance to Alkaline Environment)	-	18000	-
(clause 7.3)(Longitudinal Wicking)	-	0	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	0	-
(clause 5.1)(Fibre content (mass fraction))	-	18000	-
(clause 5.2)(Glass transition temperature)	-	0	-
(clause 5.3)(Degree of Cure)	-	0	-
(clause 5.4.2)(Measured cross sectional area)	-	18000	-
(Table 1)("Minimum bend radius in case of bent bars")	-	18000	-
(clause 6.1 and 8.2.3)(Ultimate Tensile force)	-	18000	-
(clause 6.2)(Tensile modulus of elasticity)	-	18000	-
(clause 6.3)(Ultimate Tensile Strain)	-	18000	-
(clause 6.4)(Transverse shear strength)	-	0	-
(clause 6.5)(Bond Strength)	-	18000	Additional 6000 for Bond Strength
(clause 6.6)(Fatigue Tensile Strength)	-	0	-
(clause 6.7)(Creep Failure)	-	0	-
(clause 7.1)("Moisture absorption (Short term & Long Term)")	-	18000	-
(clause 7.2)(Resistance to Alkaline Environment)	-	18000	-
(clause 7.3)(Longitudinal Wicking)	-	0	-
(clause 8.2.4)(Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar)	-	0	-

10 Apr, 2028

-
Included w.e.f. 15.10.2025 Exclusion : "(clause 5.2) (Glass transition temperature) (clause 5.3) (Degree of Cure) (clause 6.4) (Transverse shear strength) (clause 6.6) (Fatigue Tensile Strength) (clause 6.7) (Creep Failure) (clause 7.3) (Longitudinal Wicking) (clause 8.2.4) (Guaranteed ultimate tensile force at 90 degree and tensile modulus of elasticity of bent bar) "

IS 7092 : Part 1 (1992)

Aluminium alloy tubes for irrigation purposes - Specification: Part 1 welded tubes (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	15000	-
5(Workmanship and Finish)	-	15000	-
8(Dimensions)	-	15000	-
7.2(Mechanical properties)	-	15000	-
7.3(Flattening test)	-	15000	-
7.4(Hydrostatic test)	-	15000	-

10 Apr, 2028

-
Included w.e.f.08.10.2025

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	6000	-
6(FREEDOM FROM DEFECTS)	-	6000	-
8(DIMENSIONS AND TOLERANCES)	-	6000	-
10(MECHANICAL PROPERTIES)	-	6000	-
Cl. 9(Aluminium)	-	6000	-
Cl. 9(Copper)	-	6000	-
Cl. 9(Magnesium)	-	6000	-
Cl. 9(Silicon)	-	6000	-
Cl. 9(Iron)	-	6000	-
Cl. 9(Manganese)	-	6000	-
Cl. 9(Zinc)	-	6000	-
Cl. 9(Titanium and/or other grain refining elements)	-	6000	-
Cl. 9(Chromium)	-	6000	-
Cl. 9(Ti+V)	-	6000	-
Cl. 9(Cr+Mn)	-	6000	-
Clause-10(Tensile strength)	-	6000	-

10 Apr, 2028

-
Included w.e.f.08.10.2025

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	14000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	14000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	14000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	14000	-
Cl-4.1(Main body of utensil)	-	14000	-
Cl-4.1(Cast cookware)	-	14000	-
Cl-4.1(Other aluminum components and parts)	-	14000	-
Cl-4.1.1(Lids (material))	-	14000	-
Cl-4.1.1(Minimum thickness of lid)	-	14000	-
Cl-4.1.2(Minimum thickness of glass)	-	14000	-
Cl-4.1.2(Material of rim)	-	14000	-
Cl-4.1.2(Minimum thickness of rim)	-	14000	-
Cl-4.2(Material of strips)	-	14000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Rivets used in lunch box)	-	14000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	14000	-
Cl-4.5(Rivets for fixing of handles)	-	14000	-
Cl-4.5(Material of cap)	-	14000	-
Cl-4.6(Strips used for flame guards)	-	14000	-
Cl-4.6(stainless steel)	-	14000	-
Cl-5(Fabrication)	-	14000	-
Cl-6(Shape and Dimensions)	-	14000	-
Cl-7.1(Handles, when fitted)	-	14000	-
Cl-7.2(Handles)	-	14000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	14000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	14000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	14000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	14000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	14000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	14000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	14000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	14000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	14000	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	14000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	14000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	14000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	14000	-
Cl-8(Workmanship and Finish)	-	14000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	14000	-
Cl-8.3(Minimum nominal thickness)	-	14000	-
Cl-8.3(Thickness of hard anodized)	-	14000	-
Cl-8.3(Finish and appearance of hard anodized)	-	14000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	14000	-
Cl-8.3(Colour of hard anodized)	-	14000	-
Cl-8.3(Hardness of hard anodized)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	14000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	14000	-
Cl-8.6(Ceramic coating)	-	14000	-
Cl-8.7(The thickness test, adhesion test)	-	14000	-
Cl-8.7(Minimum thickness of coating)	-	14000	-
Cl-8.7.1(Dry heat the cookware)	-	14000	-
Cl-8.8(Requirements of PTFE)	-	14000	-
Cl-8.9(Material for induction plate)	-	14000	-
Cl-8.9(Test for Induction compatible base)	-	14000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	14000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	14000	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	14000	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	14000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	14000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	14000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	14000	-
Cl-9.1(Normal Capacity)	-	14000	-
Cl-9.2(Normal Capacity of internal diameter)	-	14000	-
Cl 3.1.4 Table 3 (Amendment No.1)(Thickness of cast cookware- Cast Aluminium- Minimum Base Thickness of Body)	-	14000	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	14000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	14000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	14000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	14000	-
Cl-4.1(Main body of utensil)	-	14000	-
Cl-4.1(Cast cookware)	-	14000	-
Cl-4.1(Other aluminum components and parts)	-	14000	-
Cl-4.1.1(Lids (material))	-	14000	-
Cl-4.1.1(Minimum thickness of lid)	-	14000	-
Cl-4.1.2(Minimum thickness of glass)	-	14000	-
Cl-4.1.2(Material of rim)	-	14000	-
Cl-4.1.2(Minimum thickness of rim)	-	14000	-
Cl-4.2(Material of strips)	-	14000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Rivets used in lunch box)	-	14000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	14000	-
Cl-4.5(Rivets for fixing of handles)	-	14000	-
Cl-4.5(Material of cap)	-	14000	-
Cl-4.6(Strips used for flame guards)	-	14000	-
Cl-4.6(stainless steel)	-	14000	-
Cl-5(Fabrication)	-	14000	-
Cl-6(Shape and Dimensions)	-	14000	-
Cl-7.1(Handles, when fitted)	-	14000	-
Cl-7.2(Handles)	-	14000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	14000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	14000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	14000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	14000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	14000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	14000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	14000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	14000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	14000	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	14000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	14000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	14000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	14000	-
Cl-8(Workmanship and Finish)	-	14000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	14000	-
Cl-8.3(Minimum nominal thickness)	-	14000	-
Cl-8.3(Thickness of hard anodized)	-	14000	-
Cl-8.3(Finish and appearance of hard anodized)	-	14000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	14000	-
Cl-8.3(Colour of hard anodized)	-	14000	-
Cl-8.3(Hardness of hard anodized)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	14000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	14000	-
Cl-8.6(Ceramic coating)	-	14000	-
Cl-8.7(The thickness test, adhesion test)	-	14000	-
Cl-8.7(Minimum thickness of coating)	-	14000	-
Cl-8.7.1(Dry heat the cookware)	-	14000	-
Cl-8.8(Requirements of PTFE)	-	14000	-
Cl-8.9(Material for induction plate)	-	14000	-
Cl-8.9(Test for Induction compatible base)	-	14000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	0	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	14000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	14000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	14000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	14000	-
Cl-9.1(Normal Capacity)	-	14000	-
Cl-9.2(Normal Capacity of internal diameter)	-	14000	-
Cl 3.1.4 Table 3 (Amendment No.1)(Thickness of cast cookware- Cast Aluminium- Minimum Base Thickness of Body)	-	14000	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	14000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	14000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	14000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	14000	-
Cl-4.1(Main body of utensil)	-	14000	-
Cl-4.1(Cast cookware)	-	14000	-
Cl-4.1(Other aluminum components and parts)	-	14000	-
Cl-4.1.1(Lids (material))	-	14000	-
Cl-4.1.1(Minimum thickness of lid)	-	14000	-
Cl-4.1.2(Minimum thickness of glass)	-	14000	-
Cl-4.1.2(Material of rim)	-	14000	-
Cl-4.1.2(Minimum thickness of rim)	-	14000	-
Cl-4.2(Material of strips)	-	14000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Clips of lunch box)	-	14000	-
Cl-4.3(Rivets used in lunch box)	-	14000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	14000	-
Cl-4.5(Rivets for fixing of handles)	-	14000	-
Cl-4.5(Material of cap)	-	14000	-
Cl-4.6(Strips used for flame guards)	-	14000	-
Cl-4.6(stainless steel)	-	14000	-
Cl-5(Fabrication)	-	14000	-
Cl-6(Shape and Dimensions)	-	14000	-
Cl-7.1(Handles, when fitted)	-	14000	-
Cl-7.2(Handles)	-	14000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	14000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	14000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	14000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	14000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	14000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	14000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	14000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	14000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	14000	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	14000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	14000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	14000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	14000	-
Cl-8(Workmanship and Finish)	-	14000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	14000	-
Cl-8.3(Minimum nominal thickness)	-	14000	-
Cl-8.3(Thickness of hard anodized)	-	14000	-
Cl-8.3(Finish and appearance of hard anodized)	-	14000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	14000	-
Cl-8.3(Colour of hard anodized)	-	14000	-
Cl-8.3(Hardness of hard anodized)	-	14000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	14000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	14000	-
Cl-8.6(Ceramic coating)	-	14000	-
Cl-8.7(The thickness test, adhesion test)	-	14000	-
Cl-8.7(Minimum thickness of coating)	-	14000	-
Cl-8.7.1(Dry heat the cookware)	-	14000	-
Cl-8.8(Requirements of PTFE)	-	14000	-
Cl-8.9(Material for induction plate)	-	14000	-
Cl-8.9(Test for Induction compatible base)	-	14000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	0	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	14000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	14000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	14000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	14000	-
Cl-9.1(Normal Capacity)	-	14000	-
Cl-9.2(Normal Capacity of internal diameter)	-	14000	-
Cl 3.1.4 Table 3 (Amendment No.1)(Thickness of cast cookware- Cast Aluminium- Minimum Base Thickness of Body)	-	14000	-

10 Apr, 2028

-
Included w.e.f. 14.01.2026 Exclusion: "Cl-8.10.1 (Tests for Lunch Boxes- Performance Test) Cl-8.10.2 (Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)"

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

All Designation

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	8500	-
7.0(Dimension and Tolerances)	-	8500	-
8.1 Table-1(Al)	-	8500	-
8.1 Table-1(Cu)	-	8500	-
8.1 Table-1(Mg)	-	8500	-
8.1 Table-1(Si)	-	8500	-
8.1 Table-1(Fe)	-	8500	-
8.1 Table-1(Mn)	-	8500	-
8.1 Table-1(Zn)	-	8500	-
8.1 Table-1(Ti)	-	8500	-
8.1 Table-1(Cr)	-	8500	-
9.1(Tensile Strength)	-	8500	-
9.3(Wrapping Test)	-	8500	-
10(Selection of Test Samples)	-	8500	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

All Designation

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	5500	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	5500	-
Cl. 4 (b)(Condition - IS 737)	-	5500	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	5500	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	5500	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	5500	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	5500	-
Cl. 4 (g)(Packing Mode - IS 737)	-	5500	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	5500	-
Cl. 6(Freedom from Defects - IS 737)	-	5500	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	5500	-
Cl. 7(Al - IS 504)	-	5500	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	5500	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	5500	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	5500	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	5500	-
Cl. 8.2(Bend Test - IS 1599)	-	5500	-
Cl. 9(Condition - IS 737/ IS 5052)	-	5500	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	5500	-
Cl. 11(Selection of Test Samples - IS 737)	-	5500	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	5500	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	5500	-
Cl. 12(Retests - IS 737/ IS 10259)	-	5500	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	5500	-
Cl. 13.1(Marking - IS 737)	-	5500	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

All Designation

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	5000	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	5000	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	5000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	5000	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	5000	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	5000	-
7(Dimension - IS 3965)	-	5000	-
11(Marking)	-	5000	-
Table-1, Clause - 5.1(Copper)	-	5000	-
Table-1, Clause - 5.1(Iron)	-	5000	-
Table-1, Clause - 5.1(Magnesium)	-	5000	-
Table-1, Clause - 5.1(Manganese)	-	5000	-
Table-1, Clause - 5.1(Titanium)	-	5000	-
Table-1, Clause - 5.1(Silicon)	-	5000	-
Table-1, Clause - 5.1(Chromium)	-	5000	-
Table-1, Clause - 5.1(Zinc)	-	5000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	12000	-
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	12000	-
5.1.6(Ash content - IS 2508: 2024)	-	12000	-
5.1.6(carbon black dispersion - IS 2530: 1963)	-	12000	-
5.1.1(Appearance)	-	12000	-
5.1.2(Film Form)	-	12000	-
5.1.3(Odour)	-	12000	-
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	12000	-
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	12000	-
5.2.1.2(Nominal Width)	-	12000	-
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	12000	-
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	12000	-
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	12000	-
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	12000	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	12000	-
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	12000	-
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	12000	-
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	12000	-
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	12000	-
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	12000	-
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	12000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Heat Treatment)	-	8000	-
Cl 9(Tensile & Hardness)	-	8000	-
Cl 10(Diameter & Out Of Round)	-	8000	-
Cl 8(Heat Treatment)	-	8000	-
Cl 9(Tensile & Hardness)	-	8000	-
Cl 10(Diameter & Out Of Round)	-	8000	-
Cl 8(Heat Treatment)	-	8000	-
Cl 9(Tensile & Hardness)	-	8000	-
Cl 10(Diameter & Out Of Round)	-	8000	-
10 & 10.1, Dia over 20 mm (Out of round)	-	8000	-
10 & 10.1, Dia over 20 mm (Size, Tolerance)	-	8000	-
10 & 10.1, Dia over 16 mm upto 20 mm (Out of round)	-	8000	-
10 & 10.1, Dia over 16 mm upto 20 mm (Size, Tolerance)	-	8000	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Out of round)	-	8000	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Size, Tolerance)	-	8000	-
10 & 10.1, Dia- (5.5-9.5 mm)(Out of round)	-	8000	-
10 & 10.1, Dia- (5.5-9.5 mm)(Size, Tolerance)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X30Cr13)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X30Cr13)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X20Cr13)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X20Cr13)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(0.2% Proof Stress)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(Hardness)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(%Elongation)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(Ultimate Tensile Strength)	-	8000	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(0.2% Proof Stress)	-	8000	-
8(Steel Wire rod may be supplied in the annealed condition.)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nitrogen)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Titanium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Niobium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X30Cr13)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X20Cr13)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X12Cr13)(Carbon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Molybdenum)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Copper)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Aluminium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Phosphorous)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Sulphur)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Chromium)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Nickel)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Manganese)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Silicon)	-	8000	-
7, Table 1of IS:6527 (Designation X04Cr13)(Carbon)	-	8000	-
6(The wire rods shall be smooth on surface and free from harmful surface defects)	-	8000	-
Cl. 10.1(Out of Round)	-	8000	-
Cl. 9.2 Table 4(Hardness)	-	8000	-
Cl. 9 .1 Table 3(Elongation)	-	8000	-
Cl. 9 .1 Table 3(0.2 % Proof Stress )	-	8000	-
Cl. 6(Freedom from defects)	-	8000	-
Cl 10(Diameter & Out Of Round)	-	8000	-
Cl 9(Tensile & Hardness)	-	8000	-
Cl 8(Heat Treatment)	-	8000	-
Cl 8(Heat Treatment)	-	8000	-
Cl 9(Tensile & Hardness)	-	8000	-
Cl 10(Diameter & Out Of Round)	-	8000	-
13(Corrosion resistance-IS 10461,Part-1 & 2)	-	8000	-
13(Corrosion Resistance - IS 10461)	-	8000	-
15(Marking)	-	8000	-

10 Apr, 2028

-
Included w.e.f 28.10.2025

IS 6528 (2024)

Stainless steel wire - Specification ( Second Revision )

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 6(FREEDOM FROM DEFECTS)	-	10000	-
As per clause 7(CARBON)	-	10000	-
As per clause 7(SILICON)	-	10000	-
As per clause 7(MANGANESE)	-	10000	-
As per clause 7(PHOSPHORUS)	-	10000	-
As per clause 7(SULPHUR)	-	10000	-
As per clause 7(CHROMIUM)	-	10000	-
As per clause 7(MOLYBEDNUM)	-	10000	-
As per clause 7(NICKEL)	-	10000	-
As per clause 7(NITROGEN)	-	10000	-
As per clause 7(COPPER)	-	10000	-
As per clause 7(NIOBIUM)	-	10000	-
As per clause 7(TITANIUM)	-	10000	-
As per clause 7(ALUMINIUM)	-	10000	-
As per clause 8(HEAT TREATMENT)	-	10000	-
As per clause 9(Dimension Tolerance)	-	10000	-
As per clause 10(TENSILE TEST)	-	10000	-
As per clause 10.2(REVERSE BEND TEST)	-	10000	-
As per clause 10.3(TORSION TEST)	-	10000	-
As per clause 14(FINISH)	-	10000	-
As per clause 15(CORROSION RESISTANCE)	-	10000	-
As per clause 16.2(MARKING)	-	10000	-

10 Apr, 2028

-
Included w.e.f 05.05.2025

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl - 9.1,9.5,13.2(Thickness or Diameter)	-	10000	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 0.2 MP)	-	10000	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 1.0 MP)	-	10000	-
Cl - 9.1,9.5,13.2(Tensile Strength)	-	10000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Long.)	-	10000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Tr.)	-	10000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Long.)	-	10000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Tr.)	-	10000	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Delivery Condition)	-	10000	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Sensitized Condition)	-	10000	-
Cl - 9.1,9.5,13.2(Hardness)	-	10000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture)	-	10000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 450 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 500 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 550 Deg. C)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 100 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 150 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 200 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 250 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 300 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 350 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 400 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 450 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 550 Deg. C.)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	10000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	10000	-
Cl-7.1, 7.2(C)	-	10000	-
Cl-7.1, 7.2(Si)	-	10000	-
Cl-7.1, 7.2(Mn)	-	10000	-
Cl-7.1, 7.2(P)	-	10000	-
Cl-7.1, 7.2(S)	-	10000	-
Cl-7.1, 7.2(Cr)	-	10000	-
Cl-7.1, 7.2(Mo)	-	10000	-
Cl-7.1, 7.2(Ni)	-	10000	-
Cl-7.1, 7.2(N)	-	10000	-
Cl-7.1, 7.2(Cu)	-	10000	-
Cl-7.1, 7.2(Ti)	-	10000	-
Cl-7.1, 7.2(W)	-	10000	-
Cl-7.1, 7.2(Nb)	-	10000	-
cL-7.1, 7.2(Co)	-	10000	-
Cl-7.1, 7.2(Ti: (C + N))	-	10000	-
Cl-7.1, 7.2(V)	-	10000	-
Cl-7.1, 7.2(Al)	-	10000	-
Cl-7.1, 7.2(Boron)	-	10000	-
Cl-7.1, 7.2(Tungsten)	-	10000	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1((Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.))	-	10000	-
Cl 6((freedom from defects))	-	10000	-
Cl. 12((dimension and tolerance))	-	10000	-
Cl. 14((corrosion resistance))	-	10000	-

10 Apr, 2028

-
Included w.e.f 05.05.2025

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Types)	-	11000	-
Clause.4.0(Carbon)	-	11000	-
Clause.4.0(Sulphur)	-	11000	-
Clause.4.0(Sulphur)	-	11000	-
Clause.4.0(Phosphorus)	-	11000	-
Clause.4.0(Silicon)	-	11000	-
Clause.4.0(Manganese)	-	11000	-
Clause.5.0(Supply of Material)	-	11000	-
Clause.5.0(Supply of Material)	-	11000	-
Clause.6.0(Workmanship)	-	11000	-
Clause.7.0(Straightness)	-	11000	-
Clause.8.0(Basis of Calculation)	-	11000	-
Clause.9.0(Length)	-	11000	-
Clause.10.0(Dimensions and properties)	-	11000	-
Clause.10.0(Dimensions and properties)	-	11000	-
Clause.11.0(General)	-	11000	-
Clause.11.0(Outside Dimension)	-	11000	-
Clause.11.0(Thickness)	-	11000	-
Clause.11.0(Thickness)	-	11000	-
Clause.11.0(Concavity and Convexity)	-	11000	-
Clause.11.0(Squareness of Sides)	-	11000	-
Clause.11.0(External Corner Radiius)	-	11000	-
Clause.11.0(Straightness and twist)	-	11000	-
Clause.12.0(Dimension Tolerances)	-	11000	-
Clause.12.0(Dimension Tolerances)	-	11000	-
Clause.13.0(Surface Protection)	-	11000	-
Clause.14.0(Testing)	-	11000	-
Clause.15.0(Tensile test)	-	11000	-
Clause.15.0(Yield strength)	-	11000	-
Clause.15.0(Elognation Percent)	-	11000	-
Clause.18.0(Marking)	-	11000	-
6(Workmanship)	-	11000	-
10(Dimensions and Properties)	-	11000	-
11(Measurement of Shape and Size)	-	11000	-
12(Dimensions and Tolerances)	-	11000	-
13(Surface Protection)	-	11000	-
15(Tensile Test)	-	11000	-
Clause. 3.0(Types)	-	-	-
Clause.4.0(Carbon)	-	-	-
Clause.4.0(Sulphur)	-	-	-
Clause.4.0(Sulphur)	-	-	-
Clause.4.0(Phosphorus)	-	-	-
Clause.4.0(Silicon)	-	-	-
Clause.4.0(Manganese)	-	-	-
Clause.5.0(Supply of Material)	-	-	-
Clause.5.0(Supply of Material)	-	-	-
Clause.6.0(Workmanship)	-	-	-
Clause.7.0(Straightness)	-	-	-
Clause.8.0(Basis of Calculation)	-	-	-
Clause.9.0(Length)	-	-	-
Clause.10.0(Dimensions and properties)	-	-	-
Clause.10.0(Dimensions and properties)	-	-	-
Clause.11.0(General)	-	-	-
Clause.11.0(Outside Dimension)	-	-	-
Clause.11.0(Thickness)	-	-	-
Clause.11.0(Thickness)	-	-	-
Clause.11.0(Concavity and Convexity)	-	-	-
Clause.11.0(Squareness of Sides)	-	-	-
Clause.11.0(External Corner Radiius)	-	-	-
Clause.11.0(Straightness and twist)	-	-	-
Clause.12.0(Dimension Tolerances)	-	-	-
Clause.12.0(Dimension Tolerances)	-	-	-
Clause.13.0(Surface Protection)	-	-	-
Clause.14.0(Testing)	-	-	-
Clause.15.0(Tensile test)	-	-	-
Clause.15.0(Yield strength)	-	-	-
Clause.15.0(Elognation Percent)	-	-	-
Clause.18.0(Marking)	-	-	-
6(Workmanship)	-	-	-
10(Dimensions and Properties)	-	-	-
11(Measurement of Shape and Size)	-	-	-
12(Dimensions and Tolerances)	-	-	-
13(Surface Protection)	-	-	-
15(Tensile Test)	-	-	-

10 Apr, 2028

-
Included w.e.f 05.05.2025

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(Classification of pipes)	-	500	Complete Testing Charges Rs 90000
6.2.1 Annex B(Chloride Content of Resin)	-	500	Complete Testing Charges Rs 90000
6.3(Compound Properties)	-	10000	Complete Testing Charges Rs 90000
6.3.1 Annex B(Chloride content)	-	500	Complete Testing Charges Rs 90000
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	5000	Complete Testing Charges Rs 90000
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	1000	Complete Testing Charges Rs 90000
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	200	Complete Testing Charges Rs 90000
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	200	Complete Testing Charges Rs 90000
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	200	Complete Testing Charges Rs 90000
7.1.3 (Effective length)	-	200	Complete Testing Charges Rs 90000
8(Pipe Ends)	-	200	Complete Testing Charges Rs 90000
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	9000	Complete Testing Charges Rs 90000
9.1(Visual Appearance)	-	200	Complete Testing Charges Rs 90000
9.1(Visual Appearance)	-	200	Complete Testing Charges Rs 90000
9.2 IS 12235 (Part 3)(Opacity)	-	1500	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	1000	Complete Testing Charges Rs 90000
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	1500	Complete Testing Charges Rs 90000
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1500	Complete Testing Charges Rs 90000
9.6 IS 12235(Part 14)(Density)	-	1000	Complete Testing Charges Rs 90000
10(Mechanical Properties)	-	75000	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	2500	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	5000	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	10000	Complete Testing Charges Rs 90000
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	45000	Complete Testing Charges Rs 90000
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	2500	Complete Testing Charges Rs 90000
10.4 IS 12235(Part 19)(Flattening Test)	-	1500	Complete Testing Charges Rs 90000
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	2500	Complete Testing Charges Rs 90000
5 Table 1(Classification of pipes)	-	500	Complete Testing Charges Rs 90000
6.2.1 Annex B(Chloride Content of Resin)	-	500	Complete Testing Charges Rs 90000
6.3(Compound Properties)	-	10000	Complete Testing Charges Rs 90000
6.3.1 Annex B(Chloride content)	-	500	Complete Testing Charges Rs 90000
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	1000	Complete Testing Charges Rs 90000
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	1000	Complete Testing Charges Rs 90000
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	200	Complete Testing Charges Rs 90000
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	200	Complete Testing Charges Rs 90000
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	200	Complete Testing Charges Rs 90000
7.1.3 (Effective length)	-	500	Complete Testing Charges Rs 90000
8.0(Pipe Ends)	-	500	Complete Testing Charges Rs 90000
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	10000	Complete Testing Charges Rs 90000
9.1(Visual Appearance)	-	500	Complete Testing Charges Rs 90000
9.1(Visual Appearance)	-	500	Complete Testing Charges Rs 90000
9.2 IS 12235 (Part 3)(Opacity)	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	1000	Complete Testing Charges Rs 90000
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	1000	Complete Testing Charges Rs 90000
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	1500	Complete Testing Charges Rs 90000
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1500	Complete Testing Charges Rs 90000
9.6 IS 12235(Part 14)(Density)	-	1000	Complete Testing Charges Rs 90000
10.0(Mechanical Properties)	-	70000	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	2500	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	5000	Complete Testing Charges Rs 90000
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	10000	Complete Testing Charges Rs 90000
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	45000	Complete Testing Charges Rs 90000
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	2500	Complete Testing Charges Rs 90000
10.4 IS 12235(Part 19)(Flattening Test)	-	1500	Complete Testing Charges Rs 90000
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	2500	Complete Testing Charges Rs 90000
7.1.2(Wall Thickness (Maximum))	-	200	Complete Testing Charges Rs 90000
7.1.1(Outside Diameter at any point (Maximum))	-	200	Complete Testing Charges Rs 90000
6.3(K value Test)	-	1500	Complete Testing Charges Rs 90000
6.3.3(Density)	-	1000	Complete Testing Charges Rs 90000

10 Apr, 2028

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Standard Testing Laboratory Private Limited

PLOT NO.782,KANJHAWALA INDUSTRIAL AREA,NEW DELHI,NORTH WEST, Delhi, North West, Delhi, 110081

9310136320 standardtestinglaboratory@yahoo.com

Scope List