BIS - LIMS (Laboratory Information Management System)

Delhi Analytical Research Laboratory

PLOT NO-2, TIMBER BLOCK, JHILMIL INDUSTRIAL AREA NEAR DILSHAD GARDEN METRO STATION, NEW Delhi, East, Delhi, 110095

9717324010 darltesting@gmail.com

Scope List

Reset

24 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

ALL

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 (Z) )	-	0	-
table 1 sl.no: 02(20 (Z) )	-	0	-
table 1 sl.no: 03(25 (Z) )	-	0	-
table 1 sl.no: 04(32 (Z) )	-	0	-
table 1 sl.no: 05(40 (Z) )	-	0	-
table 1 sl.no: 06(50 (Z) )	-	0	-
table 1 sl.no: 07(63 (Z) )	-	0	-
table 1 sl.no: 08(75 (Z) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z) )	-	0	-
table 1 sl.no: 11(125 (Z) )	-	0	-
table 1 sl.no: 12(140 (Z) )	-	0	-
table 1 sl.no: 13(160(z))	-	0	-
table 1 sl.no: 01(16 (Z1) )	-	0	-
table 1 sl.no: 02(20 (Z1) )	-	0	-
table 1 sl.no: 03(25 (Z1) )	-	0	-
table 1 sl.no: 04(32 (Z1) )	-	0	-
table 1 sl.no: 05(40 (Z1) )	-	0	-
table 1 sl.no: 06(50 (Z1) )	-	0	-
table 1 sl.no: 07(63 (Z1) )	-	0	-
table 1 sl.no: 08(75 (Z1) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z1) )	-	0	-
table 1 sl.no: 11(125 (Z1) )	-	0	-
table 1 sl.no: 12(140 (Z1) )	-	0	-
table 1 sl.no: 13(160(z1))	-	0	-
2.1(General)	-	3000	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	200	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	200	-
2.2.3( inside diameter of the socket)	-	200	-
2.2.3(Socket length)	-	200	-
6.1.1(VCM Content Test)	-	2500	-
2.2.2 table 1(Laying length)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	200	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-
2.1(General)	-	0	-
6.1.1(VCM Content Test)	-	2500	-
2.2.2 table 1(Laying length)	-	0	-

-
Included w.e.f. 24.02.2026

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

ALL

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.1(General)	-	4000	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	1000	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	200	-
2.2.3(Socket length)	-	200	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	200	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-
6.1.1(VCM Content Test)	-	2500	-
2.2.2 table 1(Laying length)	-	0	-

-
Included w.e.f. 24.02.2026

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

ALL

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	1000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0	-
6.1.1(VCM Content Test)	-	2500	-
2.2.2 table 1(Laying length)	-	500	-

-
Included w.e.f. 24.02.2026

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

ALL

77500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 Table-10 (i)(Ring Stiffness)	-	2500	10 percent discount for bis
Table -1 Cl. No. 5.1, i)(Base Density)	-	100	10 percent discount for bis
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1500	10 percent discount for bis
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2500	10 percent discount for bis
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	2000	10 percent discount for bis
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	1500	10 percent discount for bis
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	6000	10 percent discount for bis
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	2500	10 percent discount for bis
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	500	10 percent discount for bis
6.3.2(Length of Pipe)	-	500	10 percent discount for bis
8.1.1 Table-10 (iv)(Creep ratio)	-	16000	10 percent discount for bis
6.3.3(Out Side Diameter)	-	500	10 percent discount for bis
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	1500	10 percent discount for bis
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	500	10 percent discount for bis
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	3500	10 percent discount for bis
6.3.5.2(Wall Thickness(e4 min))	-	500	10 percent discount for bis
9 Table 12 (ii)(Water tightness)	-	3500	10 percent discount for bis
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	200	10 percent discount for bis
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	1000	10 percent discount for bis
7.1(Appearance)	-	100	10 percent discount for bis
7.1.1(Color of Finished Pipes)	-	100	10 percent discount for bis
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1000	10 percent discount for bis
8.1.1 Table-10 (i)(Ring Stiffness)	-	0	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	0	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	0	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	0	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	0	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	0	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	0	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	0	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	0	-
6.3.2(Length of Pipe)	-	0	-
8.1.1 Table-10 (iv)(Creep ratio)	-	0	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	0	-
9 Table 12 (ii)(Water tightness)	-	0	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	0	-
7.1(Appearance)	-	0	-
7.1.1(Color of Finished Pipes)	-	0	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	0	-

-
included w.e.f 30.01.2026

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

ALL

77500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500	77500 Testing Charges For BIS and 1.0 Times of BIS Charges Extra for Others
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0	-
7.2(Physical characteristics for pipes and fittings )	-	0	-
7.3(Physical characteristics for pipes and fittings )	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.1(Marking General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
5.0(Composition of the material)	-	0	-
5.1(Composition of the material)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
5.3(Composition of the material)	-	0	-
5.4(Composition of the material)	-	0	-
6.0(DESIGNATION OF WALL CONSTRUCTIONS AND EXAMPLES OF TYPICAL JOINTING METHODS )	-	0	-
6.1(Wall Construction Designated as Type A)	-	0	-
6.2(Deswignation)	-	0	-
6.3(Dimensions of pipes and fittings)	-	0	-
6.3.1 Table 2(Mean outside diameter)	-	0	-
6.3.2 Table 3(Wall thickness)	-	0	-
6.3.3 Fig 2(Length of pipe)	-	0	-
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	0	-
6.3.4.1(Wall thickness of sockets)	-	0	-
6.3.4.2(Fabricated fittings)	-	0	-
6.3.4.3(Rotational moulded fittings)	-	0	-
6.3.4.4(Type of fittings)	-	0	-
7.0(Physical characteristics of pipes)	-	0	-
7.1(Appearance)	-	0	-
7.2(Colour )	-	0	-
7.3(Vicat softening temperature of pipes)	-	0	-
7.4(Resistance to Dichloromethane)	-	0	-
7.5(longitudinal reversion)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
8.0(Physical characteristics of fittings)	-	0	-
8.1(Appearance and colour)	-	0	-
8.2(Vicat softening temperature of fittings)	-	0	-
8.3(Effect of Heating (Stress Relief Test))	-	0	-
9.0(Mechanical characteristics ofpipes)	-	0	-
9.1(Ring stiffness)	-	0	-
9.2(Resistance to external blows at o C)	-	0	-
9.4(Creep ratio)	-	0	-
10.0(Mechanical Characteristics of fittings)	-	0	-
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	0	-
9.3(Ring flexibility)	-	0	-
11.0(Joints)	-	0	-
11.1(Elastomeric Sealing Rings)	-	0	-
11.2(Solvent cement)	-	0	-
12.0(PERFORMANCE REQUIREMENTS)	-	0	-
12.1(Elastomeric Sealing Ring Joints)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.2(Solvent cement joints)	-	0	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	0	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	0	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	0	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0	-
7.2(Physical characteristics for pipes and fittings )	-	0	-
7.3(Physical characteristics for pipes and fittings )	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.1(Marking General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-
8.4(Effect on Water)	-	0	-

-
included w.e.f 30.01.2026

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

16 to 1000

27900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Polyethylene Resin)	-	7000	10% discount to BIS
5.3 (a)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(b)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(c)(Carbon Black Master Batch)	-	1000	10% discount to BIS
5.3(d)(Carbon Black Master Batch)	-	3000	10% discount to BIS
5.4(Anti oxydent)	-	1000	10% discount to BIS
6.2(Colour)	-	100	10% discount to BIS
6.2.1(6.1.1 Identification Stripes)	-	200	10% discount to BIS
7.2(Length)	-	100	10% discount to BIS
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	200	10% discount to BIS
7.4.1.2(Ovality)	-	100	10% discount to BIS
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	11700	10% discount to BIS
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1500	10% discount to BIS
8.2(Longitudinal Reversion Test)	-	800	10% discount to BIS
8.3(Carbon black)	-	1000	10% discount to BIS
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1000	10% discount to BIS
8.5 (Oxidation Induction Time)	-	1000	10% discount to BIS
8.6(Overall migration)	-	1000	10% discount to BIS
8.7(Density-IS 7328:2020)	-	500	10% discount to BIS
8.8(Tensile Strength for Butt-fusion)	-	1000	10% discount to BIS
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1500	10% discount to BIS
8.10(Slow Crack Growth Rate)	-	4000	10% discount to BIS
8.7(Corrected Density- IS 7328:2020)	-	500	10% discount to BIS
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1500	10% discount to BIS
Clause 7.1(Visual Apperance)	-	200	10% discount to BIS

-
-

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

101300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Nominal Size(DN))	-	500	OK
3.2(Nominal Outside Diameter)	-	200	OK
3.3(Mean Inside Diameter of Socket at Entry)	-	500	OK
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	OK
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	OK
3.5(Out-of-Roundness (Ovality))	-	100	OK
3.6(Nominal Wall Thickness)	-	500	OK
3.7(Minimum Wall Thickness)	-	100	OK
3.8(Tolerance)	-	100	OK
3.9(Working Pressure)	-	10000	OK
3.1(Standard Dimension Ratio)	-	500	OK
3.11(Type Tests)	-	12000	OK
3.11(Acceptance Tests)	-	6000	OK
6(Composition)	-	3000	OK
7(Dimensions of fitting)	-	1000	OK
8.2(Opacity)	-	1000	OK
8.1(Visual Appearance)	-	200	OK
8.3(Stress Relief Test)	-	2000	OK
8.4(Vicat softening Temperature)	-	2000	OK
8.5(Density)	-	1000	OK
8.6(Effect on water)	-	4000	OK
9(Mechanical Properties)	-	5000	OK
11(Marking)	-	300	OK
Cl-6.2.2(Compound Chlorine Content)	-	3000	OK
Cl-6.2.5(Verification of the Malfunction Temperature)	-	8000	OK
Cl-9.1(Hydrostatic Characteristics)	-	120000	OK
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	50000	OK
3.1(Nominal Size(DN))	-	100	-
3.2(Nominal Outside Diameter)	-	100	-
3.3(Mean Inside Diameter of Socket at Entry)	-	100	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	100	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	100	-
3.5(Out-of-Roundness (Ovality))	-	100	-
3.6(Nominal Wall Thickness)	-	100	-
3.7(Minimum Wall Thickness)	-	100	-
3.8(Tolerance)	-	100	-
3.9(Working Pressure)	-	100	-
3.1(Standard Dimension Ratio)	-	100	-
3.11(Type Tests)	-	30000	-
3.11(Acceptance Tests)	-	6000	-
6(Composition)	-	6000	-
7(Dimensions of fitting)	-	1000	-
8.2(Opacity)	-	1000	-
8.1(Visual Appearance)	-	200	-
8.3(Stress Relief Test)	-	1500	-
8.4(Vicat softening Temperature)	-	1500	-
8.5(Density)	-	1000	-
8.6(Effect on water)	-	4000	-
9(Mechanical Properties)	-	5000	-
11(Marking)	-	100	-
Cl-6.2.2(Compound Chlorine Content)	-	6000	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	10000	-
Cl-9.1(Hydrostatic Characteristics)	-	25000	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	12000	-
3.1(Nominal Size(DN))	-	99.41	-
3.2(Nominal Outside Diameter)	-	100	-
3.3(Mean Inside Diameter of Socket at Entry)	-	200	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	200	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	200	-
3.5(Out-of-Roundness (Ovality))	-	100	-
3.6(Nominal Wall Thickness)	-	200	-
3.7(Minimum Wall Thickness)	-	200	-
3.8(Tolerance)	-	100	-
3.9(Working Pressure)	-	500	-
3.1(Standard Dimension Ratio)	-	500	-
3.11(Type Tests)	-	20000	-
3.11(Acceptance Tests)	-	10000	-
6(Composition)	-	5000	-
7(Dimensions of fitting)	-	500	-
8.2(Opacity)	-	1000	-
8.1(Visual Appearance)	-	200	-
8.3(Stress Relief Test)	-	1500	-
8.4(Vicat softening Temperature)	-	1000	-
8.5(Density)	-	500	-
8.6(Effect on water)	-	4000	-
9(Mechanical Properties)	-	30000	-
11(Marking)	-	100	-
Cl-6.2.2(Compound Chlorine Content)	-	4000	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	12000	-
Cl-9.1(Hydrostatic Characteristics)	-	20000	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	50000	-

-
included w.e.f 27.01.2026

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

ALL

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	500	ok
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	500	ok
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	500	ok
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	ok
Cl. 6.1(Stress Relief Test- Appendix A)	-	1000	ok
Cl. 6.2(Opacity- Appendix B)	-	1000	ok
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	4000	ok
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	ok
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	ok
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	ok
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	1500	ok
6.1.1(VCM Content Test)	-	3000	ok
3(Size of Fitting -)	-	0	ok
4(Minimum thickness)	-	500	ok
5(Socket dimensions)	-	500	ok
6.1(Stress Relief Test)	-	1000	ok
6.2(Opacity)	-	1000	ok
6.3(Effect on Water)	-	4000	ok
6.4(Short-Term Hydraulic Test)	-	1500	Ok
7.2(Production Routine Tests)	-	0	ok
Cl 6.3(Effect on Water Lead (first extraction))	-	0	Repeat
Cl 6.3(Effect on Water Lead (third extraction))	-	0	Repeat
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	Repeat
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	OK
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	OK

-
Included w.e.f. 14.10.2025

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

ALL

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	1000	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	3000	-
7.3( Opacity)	-	1000	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	2500	-
8.2 table-9( Pipe Ends)	-	500	-
5 / 5.1(MATERIALS )	-	5000	-
5.3(VCM Content)	-	3000	-
5.4( K-Value)	-	2000	-
5.6 / 5.6.1( Material Classification, table -1)	-	5000	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	200	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	1000	-
7.2( Colour)	-	500	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	1000	-
8.1.2, table 4 to 7(Wall Thickness)	-	500	-
8.1.3 (Length, meter)	-	500	-
8.2 table-9(Dimensions of Integral Socket)	-	500	-
9.3 table-12( Ring Stiffness)	-	2500	-
9.4, annexure-E( Orientation Factor)	-	2500	-
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	5000	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	10000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	3000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	3000	-
12(a)( ELASTOMERIC SEALS)	-	2000	-
12(b)( ELASTOMERIC SEALS)	-	1000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	1500	-
Cl.10, Table 10/2(Effect on Water)	-	6000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	2000	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	2000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	1500	-
Cl.10, Table 10/2(Effect on Water)	-	4000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	2500	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	2500	-

-
Included w.e.f.08.10.2025

IS 13487 (2024)

Irrigation Equipment — Emitters — Specification

ALL

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Connections)	-	200	-
Cl-5.2(Emitter Ends)	-	0	-
Cl-5.3(Materials)	-	0	-
Cl-6.1(Test Specimens)	-	200	-
Cl-6.2.1(polyethylene pipe)	-	15000	-
Cl-6.2.2("grease or chemicals ")	-	100	-
Cl-6.2.3(water temperature)	-	100	-
Cl-6.3(Accuracy or Measuring Devices)	-	100	-
Cl-7.1(Construction and Workmanship)	-	100	-
Cl-7.2(Flow Paths in Emitter)	-	500	-
Cl-7.3(Resistance to Hydrostatic Pressure)	-	2000	-
Cl-7.4(Emitter Pull-Out)	-	0	-
Cl-7.4.1(In-Line Emitters)	-	1500	-
Cl-7.4.2(On-Line Emitters)	-	1500	-
Cl-8.1.1(Uniformity of Emission Rate)	-	2000	-
Cl-8.1.2(Emission Rate as Function of Inlet Pressure)	-	2000	-
Cl-8.1.3(Determination of Emitter Exponent)	-	2000	-
Cl-9(Marking)	-	0	-

-
Included w.e.f 19.05.2025

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

ALL

220000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	100	-
4.4(Colour)	-	100	-
5.1(Polyethylene compound)	-	10000	-
5.3(Anti-oxidant)	-	2000	-
5.7(PE Compound Quality Evaluation)	-	130000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	60000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.6(Resistance to Weathering)	-	60000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	200	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	1000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.4(U-V stabilizer)	-	0	-
6.1(Out of Roundness (Ovality))	-	200	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
7(Finish)	-	200	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	10000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	10000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	10000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.2(Reversion Test)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.3(Density)	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.6(Thermal Stability (Oxidation Induction Time))	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.7(Volatile Matter Content)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	5000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.9(Resistance to Weathering)	-	60000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
6.4(Length of Pipe)	-	200	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.4(Melt Flow Rate (MFR))	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.5(Pigment Dispersion)	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.10(Slow Crack Growth Rate Test)	-	8000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.11(Squeeze-off)	-	6000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(iv) Volatile content)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(v) Water content1))	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	8000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.3(Anti-Oxidant)	-	5000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	50000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.6(ii) Hydraulic characteristics)	-	50000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
5.6(iii) Thermal stability (Oxidation induction time))	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
6(Dimensions of pipes)	-	1000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
7(Finish)	-	200	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.1(Hydraulic Characteristics)	-	50000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.2(Reversion test)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.3(Density)	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.4(Melt Flow Rate)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.5(Pigment Dispersion)	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.6(Thermal Stability (Oxidation Induction Time))	-	2000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.7(Volatile Matter Content)	-	3000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.9(Resistance to Weathering)	-	60000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	5000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.10(Slow Crack Growth Rate Test)	-	8000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
8.11(Squeeze-of)	-	5000	For complete testing charge separately mterial 1-PE resin testing rate 10000/-2-compound evaluation testing rate -130000/- 3-Pipe testing rate-90000-This testing charges for BIS LAB and for other 1.5 times of bis lab.
10(Marking)	-	0	-

-
Included w.e.f 19.05.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

12 mm to 32 mm

13700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Carbon content of finished PE lateral pipe)	-	1500	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	1000	-
Cl-4.1(Material)	-	10000	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	300	-
Cl-6.0(Visual Appearance)	-	300	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	300	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	6500	-
Cl-7.2(Reversion Test)	-	1500	-
Cl-7.3(Tensile Test)	-	3000	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	2000	-
Cl-8.0(Supply of pipes)	-	300	-
Cl-9.0(Coiling)	-	300	-
Cl-11(Marking)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	0	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-

-
Included w.e.f.12.11.2024

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

40 to 160 mm

15400 View breakup
Rs.15400/-(10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour of fittings)	-	100	10% discount to BIS
7.1,Table 1(Wall thickness)	-	300	10% discount to BIS
7.2 ,Table 2&3(Socket Dimensions)	-	400	10% discount to BIS
8(Sealing Rings)	-	500	10% discount to BIS
10(Workmanship)	-	100	10% discount to BIS
12.1(Visual appearance)	-	100	10% discount to BIS
12.2(Stress relief test)	-	1000	10% discount to BIS
12.3(Vicat softening tempewrature)	-	1200	10% discount to BIS
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	1000	10% discount to BIS
Cl.15, Annex B(Sulphated Ash Content)	-	700	10% discount to BIS
16.1(Impact test)	-	1000	10% discount to BIS
17(Watet tightness of joint)	-	1500	10% discount to BIS
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1500	10% discount to BIS
7.3(Dimensions of waste trap(Nahani Trap)	-	500	10% discount to BIS
11.4,Table 5(Vent cowl)	-	500	10% discount to BIS
3(Type of Fitting)	-	100	10% discount to BIS
4(Size Designation)	-	100	10% discount to BIS
7.4(Chamfer)	-	100	10% discount to BIS
11.3(Access Openings)	-	300	10% discount to BIS
12.4(Effect on water test)	-	2000	10% discount to BIS

-
-

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

63 to 500 mm

28200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	500	10% Discount for BIS Lab
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1000	10% Discount for BIS Lab
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	1500	10% Discount for BIS Lab
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	1000	10% Discount for BIS Lab
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	1000	10% Discount for BIS Lab
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	500	10% Discount for BIS Lab
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	1000	10% Discount for BIS Lab
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	1000	10% Discount for BIS Lab
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	1000	10% Discount for BIS Lab
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	500	10% Discount for BIS Lab
5.2.1.1, T2(Compound ash content - Any Method)	-	500	10% Discount for BIS Lab
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	1000	10% Discount for BIS Lab
5.3(Density of Higher olefin - IS 7328:2020)	-	1000	10% Discount for BIS Lab
5.3(Olefin Constituents- 14333-2022)	-	1000	10% Discount for BIS Lab
5.3(Loading of Carbon Black - IS 2530:1963)	-	1000	10% Discount for BIS Lab
5.3(Ash content- Any Method)	-	500	10% Discount for BIS Lab
5.3(Toluene extract - Any Method)	-	1000	10% Discount for BIS Lab
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	1000	10% Discount for BIS Lab
5.3(Carbon black particle size - Any Method)	-	500	10% Discount for BIS Lab
5.4(Antioxidant - Any Method)	-	2000	10% Discount for BIS Lab
6.2(Colour- IS 14333-2022)	-	200	10% Discount for BIS Lab
7.1(Visual Appearance- IS 14333-2022)	-	200	10% Discount for BIS Lab
7.2(Length- IS 14333-2022)	-	200	10% Discount for BIS Lab
7.3(Coiling- IS 14333-2022)	-	200	10% Discount for BIS Lab
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	200	10% Discount for BIS Lab
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	200	10% Discount for BIS Lab
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	200	10% Discount for BIS Lab
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	2000	10% Discount for BIS Lab
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	2000	10% Discount for BIS Lab
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	2500	10% Discount for BIS Lab
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	6000	10% Discount for BIS Lab
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	2000	10% Discount for BIS Lab
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1000	10% Discount for BIS Lab
8.3(Carbon black content- IS 2530-1963)	-	1000	10% Discount for BIS Lab
8.3(Carbon black content Dispersion- IS 2530-1963)	-	1000	10% Discount for BIS Lab
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1000	10% Discount for BIS Lab
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	1500	10% Discount for BIS Lab
8.6(Density-IS 7328:2020)	-	500	10% Discount for BIS Lab
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1500	10% Discount for BIS Lab
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1500	10% Discount for BIS Lab
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1500	10% Discount for BIS Lab
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	4000	10% Discount for BIS Lab

-
Included w.e.f. 18-10-2022

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

40 to 200 mm

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Di men sion)	-	500	10% Discount for BIS Lab
5.1.2(Ovality)	-	200	10% Discount for BIS Lab
6.2 b(Material Identification - Male & Female Coupler)	-	500	10% Discount for BIS Lab
6.1(Quick Coupled Pipes and Fittings)	-	4000	10% Discount for BIS Lab
6(Visual Appearance)	-	200	10% Discount for BIS Lab
Cl.7.1.l(Visual Anneara nce)	-	200	10% Discount for BIS Lab
Cl.7.1.2(Hydraulic Characteristic)	-	1500	10% Discount for BIS Lab
Cl.7.1.2(Hydraulic Characteristic)	-	3000	10% Discount for BIS Lab
Cl.7.1.3(Reversion Test)	-	1000	10% Discount for BIS Lab
Cl.7.1.4(Tensile Test)	-	1500	10% Discount for BIS Lab
Cl.7.1.4(Elongation)	-	1500	10% Discount for BIS Lab
Cl.7.1.5(Fusion Compatibility)	-	4500	10% Discount for BIS Lab
Cl.7.1.6(Corrected Density)	-	500	10% Discount for BIS Lab
Cl.7.1.7(MFR Test)	-	1000	10% Discount for BIS Lab
Cl.7.2.l(Leakage Test)	-	1500	10% Discount for BIS Lab
Cl.7.2.2(Cl.7.2.2)	-	1000	10% Discount for BIS Lab
Cl.7.2.3(Weld ability Test)	-	4500	10% Discount for BIS Lab
Cl.6.2.6(Rubber Ring Hardness)	-	1500	10% Discount for BIS Lab
Cl.4.1.3(Den sity Test)	-	500	10% Discount for BIS Lab
Cl.4.1.3(MFR Test)	-	1000	10% Discount for BIS Lab
Cl.4.1.3(Thermal Stabi lity)	-	1500	10% Discount for BIS Lab
Cl.4.1.3, T-1(Volatile Matter)	-	1000	10% Discount for BIS Lab
Cl.4.1.3, T-1(Water Content)	-	1000	10% Discount for BIS Lab
Cl.4.1.4(Carbon Black Content)	-	1000	10% Discount for BIS Lab
Cl.4.1.4(Carbon Black Di spersion)	-	1000	10% Discount for BIS Lab
Cl.4.1.4(Carbon Black Content)	-	4000	10% Discount for BIS Lab

-
Included w.e.f. 18-10-2022

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

63 to 500 mm

22200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	100	10% discount to BIS
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	100	-10% discount to BIS
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	100	10% discount to BIS
6.1.3 (Length of Pipe)	-	100	10% discount to BIS
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	100	10% discount to BIS
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	100	10% discount to BIS
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	100	10% discount to BIS
6.1.4, Table 3(iv) Length of spigot, l1)	-	100	10% discount to BIS
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	150	10% discount to BIS
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	100	10% discount to BIS
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	100	10% discount to BIS
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	100	10% discount to BIS
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	150	10% discount to BIS
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	100	10% discount to BIS
6.1.4.1 (e3min=0.75e)	-	100	10% discount to BIS
7.1(Appearance:- )	-	100	10% discount to BIS
7.2(Colour )	-	100	10% discount to BIS
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1000	10% discount to BIS
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	800	10% discount to BIS
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1000	10% discount to BIS
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1500	10% discount to BIS
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	2000	10% discount to BIS
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	8000	10% discount to BIS
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	500	10% discount to BIS
9.2 IS 14182(b) Solvent cement)	-	3000	10% discount to BIS
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1500	10% discount to BIS
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1500	10% discount to BIS
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1500	10% discount to BIS
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1500	10% discount to BIS
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1500	10% discount to BIS
'7.5 (amdt.7)(Effect on Water (Type test))	-	3500	10% discount to BIS

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Up to 500 mm

2250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1 Fig.1(Dimension of Socket length)	-	100	10% discount to BIS
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	100	10% discount to BIS
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	100	10% discount to BIS
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	200	10% discount to BIS
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	500	10% discount to BIS
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1250	10% discount to BIS

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

40 to 315 mm

23300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	100	10% discount to BIS
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	5000	10% discount to BIS
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	100	10% discount to BIS
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	100	10% discount to BIS
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	100	10% discount to BIS
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	100	10% discount to BIS
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	500	10% discount to BIS
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	200	10% discount to BIS
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	800	10% discount to BIS
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	1500	10% discount to BIS
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1000	10% discount to BIS
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	4800	10% discount to BIS
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	10% discount to BIS
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1500	10% discount to BIS
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1000	10% discount to BIS
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	1500	10% discount to BIS
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1500	10% discount to BIS
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	2000	10% discount to BIS
8.6(Effect on Water Test)	-	3000	10% discount to BIS

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

20 to 500 mm

20100 View breakup
Rs.20100/-(10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(PVC Resin)	-	5000	10% Discount For BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	100	10% Discount For BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	100	10% Discount For BIS
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	100	10% Discount For BIS
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	100	10% Discount For BIS
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	300	10% Discount For BIS
7.1.4(Length)	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	100	10% Discount For BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	100	10% Discount For BIS
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	100	10% Discount For BIS
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	100	10% Discount For BIS
7.2.1.1 Table3(Angle of taper (Note-1))	-	100	10% Discount For BIS
8(SEALING RINGS)	-	500	10% Discount For BIS
9.1(PIPE ENDS)	-	100	10% Discount For BIS
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	100	10% Discount For BIS
10.1(Colour)	-	100	10% Discount For BIS
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	10% Discount For BIS
10.3(Effect on Water Test)	-	3000	10% Discount For BIS
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	800	10% Discount For BIS
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1000	10% Discount For BIS
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	10% Discount For BIS
10.7(Sulphated Ash Content)	-	700	10% Discount For BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	10000	10% Discount For BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	1500	10% Discount For BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	10000	10% Discount For BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	1500	10% Discount For BIS
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	11500	10% Discount For BIS
11.2(Resistance to External Blows at 0°C)	-	1200	10% Discount For BIS

-
included w.e.f. 11-02-2022.

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

12 to 25 mm

12400 View breakup
Rs.12400/-(10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.2(Fittings)	-	500	10% discount to BIS
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	800	10% discount to BIS
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	800	10% discount to BIS
8.2.2(Regulated Emitting Pipes)	-	800	10% discount to BIS
8.3.1(Wall Thickness ofEmitting Pipe)	-	200	10% discount to BIS
8.3.2(Inside Diameter ofEmitting Pipe)	-	300	10% discount to BIS
8.3.3(Flow Paths in Emitting Unit)	-	300	10% discount to BIS
8.3.4(Spacing ofEmitter Units)	-	200	10% discount to BIS
8.5(Resistance to Tension at Elevated Temperature)	-	1500	10% discount to BIS
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	1500	10% discount to BIS
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1500	10% discount to BIS
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1500	10% discount to BIS
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1500	10% discount to BIS
8.8(Determination of Emitting Unit Exponent)	-	1500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	700	10% discount to BIS
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	1500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	500	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	700	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	1000	10% discount to BIS
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	1000	10% discount to BIS
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	800	10% discount to BIS
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1500	10% discount to BIS
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1500	10% discount to BIS

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

Up to 355 mm

8700 View breakup
Rs.8700/-(10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	100	10% discount to BIS
6(Dimensions of pipes)	-	100	10% discount to BIS
7(Visual Appearance)	-	100	10% discount to BIS
8.1(Hydraulic characteristics)	-	3500	10% discount to BIS
8.2(Reversion)	-	1000	10% discount to BIS
8.3(Density)	-	500	10% discount to BIS
8.4(Melt Flow Rate)	-	1000	10% discount to BIS
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	700	10% discount to BIS
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	10% discount to BIS
3(Designation)	-	3300	10% discount to BIS and This charges Either for resin or for Resin with master batch applicable.

-
-

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

Up to 150 mm

101600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	25000	10% discount to BIS
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	500	10% discount to BIS
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	200	10% discount to BIS
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	200	10% discount to BIS
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	200	10% discount to BIS
7.1.3 (Effective length)	-	200	10% discount to BIS
8(Pipe Ends)	-	200	10% discount to BIS
9.1(Visual Appearance)	-	200	10% discount to BIS
9.2 IS 12235 (Part 3)(Opacity)	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	500	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	1000	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	1000	10% discount to BIS
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	500	10% discount to BIS
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	800	10% discount to BIS
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	800	10% discount to BIS
9.6 IS 12235(Part 14)(Density)	-	500	10% discount to BIS
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	27100	10% discount to BIS
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1200	10% discount to BIS
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1000	10% discount to BIS
7.1.3 (Effective length)	-	0	10% discount to BIS
6.2.1 Annex B(Chloride Content of Resin)	-	1000	10% discount to BIS
6.3(Compound Properties)	-	10000	10% discount to BIS
6.3.1 Annex B(Chloride content)	-	1000	10% discount to BIS
9.1(Visual Appearance)	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1500	10% discount to BIS
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	35000	10% discount to BIS
10.4 IS 12235(Part 19)(Flattening Test)	-	2000	10% discount to BIS

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

UP TO 400 MM

16200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(COLOUR)	-	100	10% discount to BIS
9.1( Visual Appearance)	-	100	10% discount to BIS
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	100	10% discount to BIS
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	200	10% discount to BIS
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	100	10% discount to BIS
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	200	10% discount to BIS
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	100	10% discount to BIS
7.3.1(No.of Ribs)	-	100	10% discount to BIS
7.3.2(Rib height)	-	100	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	200	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	200	10% discount to BIS
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	200	10% discount to BIS
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	2000	10% discount to BIS
8.4(Sealing rings - Hardness)	-	500	10% discount to BIS
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	5000	10% discount to BIS
9.5(Tensile Strength IS 12235(Part 13))	-	1500	10% discount to BIS
9.3(Density IS 12235 (Part 14))	-	500	10% discount to BIS
9.2(Internal Diameter)	-	100	10% discount to BIS
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1500	10% discount to BIS
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	1000	10% discount to BIS
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	200	10% discount to BIS
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	1000	10% discount to BIS
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	200	10% discount to BIS
4.1.2(K-Value as per IS-4669)	-	1000	10% discount to BIS

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

12-32 MM

12700 View breakup
Rs.12700/- (10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	200	10% discount to BIS
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	200	10% discount to BIS
6.1(Visual Appearance)	-	100	10% discount to BIS
7.3(Tensile Test)	-	1200	10% discount to BIS
7.3(Elongation at Break)	-	1200	10% discount to BIS
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1800	10% discount to BIS
7.2(Reversion Test)	-	1000	10% discount to BIS
7.1(Hydraulic Characteristics)	-	4000	10% discount to BIS
4.1.c.iii (Volatile matter - Annex B )	-	1000	10% discount to BIS
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	0	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	-
6.1(Visual Appearance)	-	0	-
7.3(Tensile Test)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
7.2(Reversion Test)	-	0	-
7.1(Hydraulic Characteristics)	-	0	-
4.1.c.iii (Volatile matter - Annex B )	-	0	-
4.1.a (Potyethylene - higher olefins constituent )	-	1000	10% discount to BIS
4.1.b(Potyethylene - anti-oxidant)	-	1500	10% discount to BIS
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	700	10% discount to BIS
Cl. 4.2(Carbon Black Content)	-	700	10% discount to BIS
Cl. 4.2(Carbon Black Dispersion)	-	700	10% discount to BIS
4.1.c.i (Density)	-	500	10% discount to BIS
4.1.c.ii (Toluene extract - Annex A)	-	1000	10% discount to BIS
4.1.c.iii (Volatile matter - Annex B )	-	0	-
Cl. 5.0 & 5.1 Table -1(Outside Diameter)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1500	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	2500	-
7.2(Reversion Test)	-	0	10% discount to BIS
7.3(Tensile Test)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
8.0 (8.1) (Supply of pipes )	-	100	10% discount to BIS
9.0 (9.1)(Coiling )	-	500	10% discount to BIS

-
-

Bureau of Indian Standards

The National Standards Body of India

Delhi Analytical Research Laboratory

PLOT NO-2, TIMBER BLOCK, JHILMIL INDUSTRIAL AREA NEAR DILSHAD GARDEN METRO STATION, NEW Delhi, East, Delhi, 110095

9717324010 darltesting@gmail.com

Scope List