BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

893 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

871

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-

-
Excluding Table 1,Clause 6.1 ,sl. no.(vi) , alkali content;

872

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Ratings)	-
6 (Ratings)	-
6 (Ratings)	-
7.1.1 (Accessories Classification)	-
7.1.2 (Accessories Classification)	-
7.1.3 (Accessories Classification)	-
7.1.4 (Accessories Classification)	-
7.2.1 (Socket-Outlets Classification)	-
7.2.2 (Socket-Outlets Classification)	-
7.2.3 (Socket-Outlets Classification)	-
7.2.4 (Socket-Outlets Classification)	-
7.3 (Plug Classification)	-
8.1 (MARKING)	-
8.8 (MARKING)	-
8.9 (MARKING)	-
9.1 (CHECKING OF DIMENSIONS)	-
9.2 (CHECKING OF DIMENSIONS)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.4 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.5 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.6 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.7 (PROTECTION AGAINST ELECTRIC SHOCK)	-
11.1 (PROVISIONS FOR EARTHING)	-
11.2 (PROVISIONS FOR EARTHING)	-
11.3 (PROVISIONS FOR EARTHING)	-
11.4 (PROVISIONS FOR EARTHING)	-
11.5 (PROVISIONS FOR EARTHING)	-
11.6 (PROVISIONS FOR EARTHING)	-
12.1.1 (TERMINALS)	-
12.1.2 (TERMINALS)	-
12.2.1 (TERMINALS)	-
12.2.2 (TERMINALS)	-
12.2.3 (TERMINALS)	-
12.2.4 (TERMINALS)	-
12.2.5 (TERMINALS)	-
12.2.6 (TERMINALS)	-
12.2.7 (TERMINALS)	-
12.2.8 (TERMINALS)	-
12.2.9 (TERMINALS)	-
12.2.10 (TERMINALS)	-
12.2.11 (TERMINALS)	-
12.3.1 (TERMINALS)	-
12.3.2 (TERMINALS)	-
12.3.3 (TERMINALS)	-
12.3.4 (TERMINALS)	-
12.3.5 (TERMINALS)	-
12.3.6 (TERMINALS)	-
12.3.7 (TERMINALS)	-
12.3.8 (TERMINALS)	-
12.3.9 (TERMINALS)	-
12.3.10 (TERMINALS)	-
12.3.11 (TERMINALS)	-
12.3.12 (TERMINALS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.3 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.4 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.5 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.6 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.7 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.8 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.9 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.11 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.12 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.13 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.14 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.15 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.16 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.17 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.18 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.19 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.21 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.22 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.23 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
14.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.3 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.4 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.5 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.6 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.7 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.8 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.9 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.11 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.12 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.13 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.14 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.15 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.16 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.17 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.18 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.19 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.21 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.22 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.24 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.25 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.26 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
15 (INTERLOCKED SOCKET-OUTLETS)	-
16.1 (RESISTANCE TO AGEING,)	-
16.2 (RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-
16.3 (Resistance to Humidity)	-
17.1 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
17.2 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
19 (TEMPERATURE RISE)	-
20 (BREAKING CAPACITY)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
22.1 (Verification of the Maximum Withdrawal Force)	-
22.2 (Verification of Minimum Withdrawal Force)	-
23.1 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.3 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.4 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
24.1 (MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For surface mounting boxes)	-
24.2 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.2 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.2 (MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies other than elastomeric or thermoplastic material)	-
24.2 (MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.3 (MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-
24.4 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.4 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.4 (MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.5 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.5 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.5 (MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.6 (MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-
24.7 (MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-
24.8 (MECHANICAL STRENGTH For shuttered socket-outlets)	-
24.9 (MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.11 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.12 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.13 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.14.1 (MECHANICAL STRENGTH For fixed socket-outlets)	-
24.14.2 (MECHANICAL STRENGTH For fixed socket-outlets)	-
25.1 (RESISTANCE TO HEAT Accessories and surface mounting boxes)	-
25.2 (RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-
25.3 (RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-
25.4 (RESISTANCE TO HEAT )	-
26.1 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
27.1 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.2 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.3 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
28.1.1 (Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-
28.1.2 (Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-
28.2 (Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-
29 (RESISTANCE TO RUSTING)	-
30.1 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-
30.2 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-
30.3 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-
30.4 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-
7.1.5 (Accessories Classification)	-
8.1 (MARKING)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
23.2 (FLEXIBLE CABLES AND THEIR CONNECTION)	-

-
-

873

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

Rs.6450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.5 (Tensile Strength IS 12235(Part 13))	-
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
9.3 (Density IS 12235 (Part 14))	-
9.1 ( Visual Appearance)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B (Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Wall thickness)	-

-
Excluding Test facility not avaialble for Cl 9.4 Resistance to External Blows ,9.7 Effect on Water;

874

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (CARBON)	-
Cl.4 (SULPHUR)	-
Cl.4 (PHOSPHURS)	-
Cl.4 (MANGANESE)	-
Cl.4 (NITROGEN)	-
Cl.4 (SILICON)	-
Cl.4 (ALUMINIUM)	-
Cl.4 (CHROMIUM)	-
Cl.4 (NICKEL)	-
Cl.4 (VANADIUM)	-
Cl.4 (MOLYBDENUM)	-
3, Table-1 (Dimensions- s1)	-
3, Table-1 (Dimensions- s2)	-
3, Table-1 (Dimensions- a)	-
3, Table-1 (Dimensions- b1)	-
3, Table-1 (Dimensions- b2)	-
3, Table-1 (Dimensions- L)	-
5 (Hardness)	-
6 (Workmanship and Finish)	-
6 (Torque Testing)	-
7 (Designation)	-

-
Grade designation of material as per relevant IS may please declared.; Excluding -; torque test

875

IS 8944 (2005)

Chlorpyrifos, emulsifiable concentrates - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Chloropyrifos content)	-
3.3.2 (Acidity (as H2SO4), )	-

-
Excluding Cl. 3.3.1 Content;

876

IS 9798 (2013)

Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision)

14276 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 IS 742 (Material)	-
4.1.1 IS 2305 (Material)	-
4.2.1a (Finish)	-
4.2.1b IS 9844 IS 6009 (Finish)	-
4.3.1 (Diaphragm Material)	-
4.3.2 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.3.3 (Clamping test)	-
4.3.4 Annex C (Bursting & Pull out test)	-
4.3.5ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Diaphragm: Extractable )	-
4.3.5b IS 3400(Part 2) (Changes in hardness, before and after the immersion )	-
4.3.7 Annex E (The material shall have 25 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.4.1 (Valve Pad Material)	-
4.4.2ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.4.2aii Annex D ( Absorbed)	-
4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.4.4 (Valve Pad Material)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
4.5,4.4.1 (Seals O rings and rubber components other than diaphragm and valve pad )	-
4.5,4.4.2i Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.5,4.4.2ii Annex D ( Absorbed)	-
4.5,4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.5,4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.5,4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
5.2 (Construction and Workmanship)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.5 (Inlet Connection)	-
5.6,5.6.1 (Outlet Connection:- Non-threaded Outlet Connection)	-
5.7 (Body)	-
5.8 (Vent)	-
5.10.1 (Valve Pad Fitting)	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.11.1,8.11 Table 1 (The fixing of the inlet connection on to the regulator body , whether it is of the threaded or non - threaded type or in one piece, shall withstand the following tests, under the conditions defined in 8.11 (see Table 1))	-
5.12.1,8.11 Table 3 (The regulators when installed as indicated in the installation instruction shall resist the following tests under the conditions defined in 8.11 (see Table 3 ))	-
5.11.2a,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):a)For non - threaded hose connection)	-
5.11.2b,8.11 Table 2 (The fixing of the outlet connection on to the regulator body, whether it is of the threaded, or non-threaded type or in one piece, shall resist the following tests, under the conditions defined in 8.11 (see Table 2):b)For threaded unions)	-
6,6.1,6.2 (SOUNDNESS)	-
6,6.1,6.2 (SOUNDNESS)	-
6.3 (SOUNDNESS)	-
6.4 (SOUNDNESS)	-
8.2 (CHATTER)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.10.1 Annex G (Cycle Test)	-
6,6.1,6.2 (SOUNDNESS (After Cycle Test))	-
8.9 (Performance (After Cycle test) Inlet Pressure Flow Rate )	-
8.10.2 Annex H 8.9 (Low Temperature Test Performance test after exposure to temperature at -200 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (Static(lock up) pressure)	-
8.10.3 Annex H 8.9 (High Temperature Test Performance test after exposure to temperature at 650 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
4.4.5 Annex E (The material shall have 40 percent max compression set when subjected to compression set test in accordance with the method prescribed in Annex E.)	-
Cl. 4.2 (Aluminium)	-
Cl. 4.2 (Copper)	-
Cl. 4.2 (Magnesium)	-
Cl. 4.2 (Iron)	-
Cl. 4.2 (Lead)	-
Cl. 4.2 (Cadmium)	-
Cl. 4.2 (Tin)	-
Cl. 4.2 (Thalium+ Indium)	-
Cl. 4.2 (Nickel)	-
Cl. 4.2 (Zinc)	-
Cl. 4.2 (Chromium)	-

-
-

877

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Rs 26700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.2 (INSULATION : Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.2 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
16.4 (Flammability Test)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Conductor, Number of wires.)	-
Cl.8 (Flexibility class)	-
[(Cl.15), (d), 2] (After ageing, Elongation of Sheath [Percentage])	-

-
Except Cat C1 & C2

878

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 10.3 (UTM)	-
Cl 7 (Workmanship)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Clause - 5, 8.1 & 8.2 (E250, ALUMINIUM)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Grade/Designation, Quality type of killing and declaration regarding micro alloying elements addition may please be declared. Sample size- 5 pcs of 5 cm x 5 cm having dia> 3mm and thickness >0.8 mm; Excluding -; Y-groove crackability test

879

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

25780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Deformations and Surface Characteristics)	-
Cl 7.2 (Weight)	-
4.1 (Carbon %)	-
4.1 (Sulphur %)	-
4.1 (Phosphorus %)	-
4.1 (Manganese %)	-
4.1 ( Nitrogen%)	-
4.1 (Sulphur and phosphorous)	-
4.1 (CE)	-
Cl 5 (Deformations and Surface Characteristics)	-
Clause 8.1(Table 3) (Total Elongation at Maximum Force)	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-

-
Microalloying element/type of killing (element)/any other element to be declared; Excluding -; Pull out test,

880

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Conductor - Material)	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Annealing test (for copper))	-
4.1 (Wrapping test (for Al))	-
4.2 (Conductor resistance test)	-
5.1 (Insulation)	-
5.2 (Application )	-
5.3 (Thickness of Insulation)	-
6.1 (Filler)	-
6.2 (Filler)	-
7 (Binder Tape)	-
8.1 (Sheath Material )	-
8.3 (Thickness of Sheath)	-
9 (Overall dimensions)	-
9.1 (Ovality)	-
10.1 (HV (water immersion))	-
10.2 (HV (room temperature))	-
10.4 (Flammability test-Burning after flame removal)	-
10.4 (Flammability test- Unaffected portion)	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.11 (Per sulphate test (for tinned Cu cable only))	-
11 (Identification)	-
11.1 (Durability)	-
11.2 (Legibility)	-
12 (CONSTRUCTION Core Identification)	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) c) 4) (Cracks Observed)	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) d) 4) (Cracks Observed)	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
table 1 e) 3) (Volume Resistivity - Room temp )	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (IR constant- max. Temp)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 (Category Code)	-
10.11 (Persulphate Test )	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
8 (SHEATH)	-
18 (SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-
4.1 (Material)	-
(4.3 of IS 8130:2013) (Form of Conductor)	-
( 4.4.1 of IS 8130:2013) (Joints in Conductor)	-
(4.4.2 of IS 8130:2013) (Joints in Conductor Solid Conductors (Aluminium Conductors only))	-
(Cl.6.1.1 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1.2 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1.3 of IS 8130:2013) (Solid Conductor (Class 1))	-
(6.2.1 of IS 8130:2013) (Stranded Circular Non-compacted Conductors (Class 2))	-
(6.2.2 of IS 8130:2013) (Stranded Circular Non-compacted Conductors (Class 2))	-
(6.2.3 of IS 8130:2013) (Stranded Circular Non-compacted Conductors (Class 2))	-
(6.3.1 of IS 8130:2013) (Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-
(6.3.2 of IS 8130:2013) (Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-
(6.3.3 of IS 8130:2013) (Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-
( 6.4.1 of IS 8130:2013) (Flexible Conductors (Class 5))	-
(6.4.2 of IS 8130:2013) (Flexible Conductors (Class 5))	-
( 6.4.3 of IS 8130:2013) (Flexible Conductors (Class 5))	-
Cl.19.1.4 (Assembly of Cores)	-
Cl. 8.2 (Application of Sheath)	-

-
Test facility not available for FR, FR-LSH category.

881

IS 15658 (2006)

Precast concrete blocks for paving - Specification

Rs.15940/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2.4 (WATER ABSORPTION TEST (Average for three test specimens))	-
6.2.5 (AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-

-
Excluding -; Abrasion Resistance Test a ( Dry & Wet)

882

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 Table-2 viii (Alkali content)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
6.1 Table-2 iii. (Insoluble residue)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
6.1 Table-2 viii (Alkali content)	-
6.1 Table-2 vii (Chloride content)	-
6.1 Table-2 vi (Loss on ignition)	-
6.1 Table-2 v (Total Sulphur Content calculated as Sulphuric Anhydride)	-
6.1 Table-2 iv (Magnesia)	-
6 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
6.1 Table-2 iii. (Insoluble residue)	-
6.1 Table-2 ii. (Ratio of percentage of alumina to that of iron oxide)	-
7 Table-3 iv c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 Table-3 iv b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 Table-3 iv a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 Table-3 iii b (Setting Time Final)	-
7 Table-3 iii a (Setting Time Initial)	-
7 Table-3 ii b (Expansion by Autoclave)	-
7 Table-3 ii a (Expansion by Le Chatelier)	-
7 Table-3 i. (Fineness)	-

-
Excluding Table 2,Clause 6.1 ,sl. no.(viii) , alkali content;

883

IS 710 (2010)

Marine plywood - Specification (Second Revision)

Rs 11200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (WORKMANSHIP AND FINISH )	-
7.2 (WORKMANSHIP AND FINISH )	-
7.3 (WORKMANSHIP AND FINISH )	-
7.5 (WORKMANSHIP AND FINISH )	-
6.1 (DIMENSIONS)	-
6.2 (DIMENSIONS)	-
6.3 (DIMENSIONS)	-
9.1.1 (MOISTURE CONTENT)	-
9.1.2 , 9.1.2.1 (Glue Adhesion in Dry State)	-
9.1.2 , 9.1.2.2 (Glue Adhesion in Dry State)	-
9.1.3 , 9.1.3.1.1 (Water resistance test)	-
9.1.3 , 9.1.3.1.2 (Water resistance test)	-
9.1.5 (Mycological test)	-
9.1.4 (Tensile strength)	-
9.1.6 (Table 3) (Static bending strength)	-
9.1.6 (Table 3) (Static bending strength)	-
9.1.7 (Table 4) (Wet bending strength)	-
9.1.7 (Table 4) (Wet bending strength)	-
9.1.8 (Retention of preservative)	-
11.1 (MARKING)	-

-
-

884

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

- View breakup
Testing charges excluding the material test are :Rs.7800.00 Testing charges for the material tests are :Rs.3600.0

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.3 (Tensile Test)	-
7.3 (Elongation at Break)	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-

-
Excluding Environmental strees cracking resistance test and Cl 7.1 & Table 2 Hydraulic test;

885

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

- View breakup
Rs. 4250/-(Excluding leakage test and Hyd. Proof Test)+Testing charges as per IS 14151(Part 1)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2.1 (Visual and Workmanship Requirement)	-
4.2.7 (1 Dimensions of Quick Coupled Pipes and Fittings)	-

-
-

886

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- i (Fineness 4031 Part 2)	-

-
Excluding Table 1,Clause 6 ,sl. no.(vi) , alkali content;

887

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Colour)	-
10.1 (Surface Finish)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
5 (CLASSIFICATION OF PIPES)	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
Cl- 7.2 (Socket length (Take 4 reading & minimum will be reported))	-
7.2.1 (DIMENSIONS-Socket)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.2(a)-Table 5 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-
10.7 (Sulphated Ash Content)	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
8 (SEALING RINGS)	-
9.1 (PIPE ENDS)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.2 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-
11.2 (Resistance to External Blows at 0°C)	-
13.1 (Marking)	-
cL-13.1.1 (Marking)	-
Cl-13.1.2 (Marking)	-

-
Excluding Effect on water

888

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.3 (Carbon Black Content)	-
Cl-7.4 (Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-
8.2 (Longitudinal Reversion Test)	-
Cl 8.3 (Carbon Black Dispersion)	-
8.7 (Density)	-
8.4 ( Melt Flow Rate)	-
7.4.1.2 (Ovality)	-
7.2 (Length)	-
6.2 (Colour)	-
6.2.1 (6.1.1 Identification Stripes)	-

-
Excluding Oxidation induction , overall migration, Cl 8.7 density, Cl 7.4.1.2 ovality Cl 8.8 Tensile,Cl 8.9 Elongation at Break;

889

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (GRADE)	-
4 (Grade, Type and Construction)	-
7.3.2 (CONSTRUCTION-Stiles and Rails)	-
11.1 (Dimensions - Height)	-
11.1 (Dimensions - Width)	-
11.1 (Dimensions - Thickness)	-
11.1 (Dimensions - Variation in thickness)	-
11.12 (End immersion test)	-
11.1 (Dimensions - Squareness)	-
9.1 (Workmanship & Finish)	-
9.2 (Workmanship & Finish)	-
9.3 (Workmanship & Finish)	-
11.2 (General Flatness Test)	-
11.3 (Local Planeness Test)	-
Clause 11.4 (Impact Indentation Test)	-
11.5 (Flexure Test)	-
11.6 (Edge Loading Test)	-
11.7.1 (Shock Resistance Test)	-
11.7.2 (Shock Resistance Test)	-
Clause 11.8 (Buckling Resistance Test)	-
Clause 11.9 (Slamming Test)	-
Clause 11.10 (Misuse Test)	-
Clause 11.11 (Varying Humidity Test)	-
11.13 (Knife Test)	-
Clause 11.14 (Glue Adhesion Test)	-
Clause 11.15 (Screw Withdrawal Resistance Test)	-
7.3.3 (CONSTRUCTION-Stiles and Rails)	-

-
Excluding Test facility not available for Cl 11.2, 11.4, 11.6, 11.8, 11.9;

890

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

Rs. 5250/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Workmanship)	-
Cl 10.2 (Workmanship)	-
Cl 10.3 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 ( Nitrogen%)	-
6 (Sulphur + Phosphorus)	-
6.1 ( Nb)	-
6.1 (V)	-
6.1 ( Ti)	-
6 (carbon equivalent (CE))	-
6 (Copper as Cu)	-
Clause 6, Table 1 Note : 3 (Nb+V+Ti)	-
6.1 (Cr)	-
6.1 (Mo)	-
6.1 (Ni)	-
Cl 6.1 (Manganese)	-

-
-

891

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

- View breakup
BWP Grade 6500/- MR Grade 5400/- Testing Charges for Spot Test Only(Cl.9.2.6)-725/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2.6 (Spot test - Annexure L)	-
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (mechanical) (Spot test - Annexure L)	-

-
SIZE: One Block Board Sample Size without dimensional measurements:Length-1200 mm, width-1200

892

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Bacterial count)	-
5.6 (Coliform count )	-
5.6 (Escherichia coli)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Salmonella)	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Listeria monocytogenes)	-
4 (Description)	-
Cl 5.1 (Milk intended (IS 1479 - Part 1))	-
5.2 (Absence of extraneous matter, added colour and added flavour)	-
Cl 5.3 (Calcium chloride, citric acid and sodium citrate, sodium salts of orthophosphoric acid and polyphosphoric acid (as linear phosphate), )	-
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
5.6 (Moisture)	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Milk fat)	-
5.6 (Insolubility index)	-
5.6 (Milk fat)	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Scorched particles)	-
5.6 (Total ash (on dry basis))	-
5.6 (Coliform count )	-
5.6 (Salmonella)	-
5.6 (Bacterial count)	-

-
500 gm x 3

893

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

- View breakup
Electricity Cost (per kWh) ₹ 9.00 Testing Charges per man hour ₹ 300.00 Total testing charge for BWP Grade ₹ 7,456.00 ₹ 7,450.00 Total testing charge for BWR Grade ₹ 7,108.00 ₹ 7,100.00 Total testing charge for MR Grade ₹ 7,090.00 ₹ 7,100.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4 (Grades)	-
Cl-8.1 (Dimensions -length)	-
Cl.8.1 (Dimensions -width)	-
Cl-8.2 (Thickness of the plywood boards)	-
Cl-8.3 (Squareness)	-
Cl.8, 8.3 & Annex C (Edge Straightness)	-
Cl-11.4 (Moisture Content)	-
Cl-11.3.2 (Mycological Test)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4, (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
Cl-11.3.1, 11.3.1.1 (Water Resistance Test)	-
Cl-9 (WORKMANSHIP AND FINISH)	-

-
Excluding- Steady State Formaldehyde Emission Test (Cl. 11.7)

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List