BIS - LIMS (Laboratory Information Management System)

National Test House (NER) - NTH, Guwahati

C.I.T.I Complex, Post: Gopinath Nagar, Kalapahar, Guwahati-781016, Guwahati, Kamrup Metro, Assam, 781016

9412223452 nthner-ca@gov.in

Scope List

Reset

14 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC(FLY ASH BASED)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	2000	-
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-

13 Dec, 2027

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

OPC 33/43/ 53 Grade,OPC 43S & 53S Grade

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 viii(Alkali content)	-	2000	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	1000	-
6.1 Table-2 iv(Magnesia)	-	1000	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	1000	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	1000	-
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	500	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 iii a(Setting Time Initial)	-	500	-
7 Table-3 iii b(Setting Time Final)	-	500	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-

13 Dec, 2027

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	0	-
6.5(Size of messenger conductor )	-	0	-
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	250	-
7.3(Tolerance on thickness of insulation )	-	250	-
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	0	-
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	0	-
9.3(Direction of lay)	-	0	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	2000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	2000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	1000	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	1000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	1000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1000	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	0	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	1000	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	2000	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	750	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	750	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1500	-
6.1(Construction of phase conductor)	-	0	-
6.1(Number of wires (phase conductor))	-	0	-
6.1(Construction of Street Lighting conductor)	-	0	-
6.1(Number of wires (Street Lighting conductor))	-	0	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-

13 Dec, 2027

-
1 10.1 d) iii) (Carbon Black Content) CARBON BLACK TEST METHOD IS UNDER CONSIDERATION 2 11.4 (Bending Test on the Completed Cable ( Optional)) BENDING TEST OPTIONAL TEST 3 11.4 (Bending Test on the Completed Cable ( Optional) ) BENDING TEST OPTIONAL TEST

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	250	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	250	-
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	250	-
13.3(Armouring : Dimensions -Formed wire )	-	250	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	2000	-
13.5.2(ARMOURING : Resistance)	-	2000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	2000	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	250	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	250	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	500	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1500	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	0	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	0	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	0	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	500	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	2000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	0	-
15.1 d)6)(Heat shock test- Insulation )	-	500	-
15.1 d)6)(Heat shock test- sheath )	-	0	-
15.1 d)7)(Thermal stability- insulation )	-	1000	-
15.1 d)7)(Thermal stability- Sheath )	-	0	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1500	-
15.1 e)(Insulation resistance test : IR Constant )	-	0	-
15.1 f)(High voltage test ( water immersion test ))	-	3000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	3000	-
16.4(Flammability Test)	-	500	-
16.5(Oxygen Index Test)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	5000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	375	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	375	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	375	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	375	-
16.4(Flammability Test- Un affected portion)	-	250	-
16.4(Flammability Test- Period of Burning)	-	250	-
9.3(Minimum Thickness of Reduce core insulation)	-	250	-
9.2(Thickness of Reduce core insulation)	-	250	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	5000	-
Table 4(Copper purity test)	-	1000	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	0	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
Cl No. 16.10(Smoke density test)	-	5000	-
Table 4(Copper purity test)	-	1000	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	0	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1500	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1500	-

13 Dec, 2027

-
Included w.e.f 12.02.2026 Exclusion: Cl 16.6 (Flame Retardance Test on Single Cables), 16.7 (Flame Retardance Test on Bunched Cables)

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	0	-
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
7(OUTER SHEATH)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	250	-
9.3(Thickness of Insulation - Minimum)	-	250	-
9.4(Application of Insulation)	-	0	-
10.1(Core Identification)	-	0	-
10.2(Core Identification- Neutral)	-	0	-
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	0	-
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	250	-
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(Armouring: Direction of Lay )	-	0	-
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	250	-
13.3(Armouring : Dimensions -Formed wire )	-	0	-
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	2000	-
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	250	-
14.3(Thickness of outer sheath - minimum)	-	250	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	500	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1500	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	0	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	0	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	2000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	0	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	2000	-
16.2(HIGH VOLTAGE TEST )	-	2000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	0	-
16.9(Oxygen Index Test)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
16.14(Temperature Index)	-	50000	-
17.1(Manufacturer'. identification)	-	0	-
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 4(Copper purity test)	-	1000	-
Table 2(Cold Impact test for Outer sheath)	-	0	-
Cl 16(Halogen Acid Gas Test)	-	5000	-
Cl.8(Conductor)	-	0	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	0	-
13.6 a)(ARMOURING: Tensile Strength)	-	1500	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	0	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	2000	-
13.6 g)(ARMOURING: Resistivity)	-	1500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2000	-
Cl No. 16.15(Smoke density test)	-	5000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
3(CONDUCTOR: MATERIALS)	-	0	-
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
7(OUTER SHEATH)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	250	-
9.3(Thickness of Insulation - Minimum)	-	250	-
9.4(Application of Insulation)	-	0	-
10.1(Core Identification)	-	0	-
10.2(Core Identification- Neutral)	-	0	-
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	0	-
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	250	-
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(Armouring: Direction of Lay )	-	0	-
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	0	-
13.3(Armouring : Dimensions -Formed wire )	-	0	-
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	1500	-
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	250	-
14.3(Thickness of outer sheath - minimum)	-	250	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	500	-
15.1 a) iv)(Resistance test - Main conductor)	-	1500	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1500	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1500	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	0	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	2000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1500	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	0	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	2000	-
16.2(HIGH VOLTAGE TEST )	-	2000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	250	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	250	-
16.9(Oxygen Index Test)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	0	-
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	1000	-
Table 2(Cold Impact test for Outer sheath)	-	1500	-
Cl 16(Halogen Acid Gas Test)	-	5000	-
Cl.8(Conductor)	-	0	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1500	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1500	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	0	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
Cl No. 16.15(Smoke density test)	-	5000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-

13 Dec, 2027

-
Included w.e.f 12.02.2026 Exclusion: Cl 16.1 (Flame Retardance Test on Single Cables), 16.11 (Flame Retardance Test on Bunched Cables)

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	0	-
11.2(Legibility)	-	0	-
11.1(Durability)	-	0	-
11(Identification)	-	0	-
10.4(Flammability test- Unaffected portion)	-	250	-
10.4(Flammability test-Burning after flame removal)	-	250	-
table 1 e) 3) (IR constant- Room temp )	-	500	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	-
10.2(HV (room temperature))	-	1500	-
10.1(HV (water immersion))	-	3000	-
10.1(HV (water immersion))	-	3000	-
10.8(Smoke density rating)	-	5000	-
10.6(Halogen evolution)	-	5000	-
10.7(Temperature index)	-	5000	-
10.5(Oxygen index)	-	5000	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	1000	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500	-
Table 1 iii) c) 3)(Elongation variation)	-	500	-
Table 1 iii) c) 3)(TS variation)	-	500	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	500	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500	-
8.3(Thickness of Sheath)	-	250	-
5.3(Thickness of Insulation)	-	250	-
4.2(Conductor resistance test)	-	1500	-
4.1(Wrapping test (for Al))	-	500	-
9.1(Ovality)	-	250	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	-
Table 1 iii) d) 4)(Cracks Observed)	-	500	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	1500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	1500	-
9(Overall dimensions)	-	250	-
4.1(Annealing test (for copper))	-	1000	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
table 1 e) 3) (IR constant- max. Temp)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	250	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	0	-
7(Binder Tape)	-	0	-
15(PACKING AND MARKING)	-	0	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
9(OVERALL DIMENSIONS)	-	250	-
Cl. 8.2(Application of Sheath)	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	1000	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	1000	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	1000	-
Table 1 iii) c) 4)(Cracks Observed)	-	500	-
10.1(High Voltage Test (Water Immersion Test))	-	3000	-
10.4(Flammability Test)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	1000	-
12(CONSTRUCTION Core Identification)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	0	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	2000	-
8.1(Sheath Material )	-	0	-
12.0(Core identification)	-	0	-
Table 1(Category Code)	-	0	-
5.3(Minimum thickness of insulation)	-	250	-
5.3(Avarage thickness of insulation)	-	250	-
10.8(Smoke Density Rating)	-	5000	-
12(CORE IDENTIFICATION)	-	0	-
13(CABLE CODE)	-	0	-
4.1(Conductor - Material)	-	0	-
4.1(Conductor - Material)	-	0	-
5.3(Thickness of Insulation)	-	250	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
9(OVERALL DIMENSIONS)	-	250	-
Cl. 8.2(Application of Sheath)	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
5.3(Thickness of Insulation)	-	250	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
9(OVERALL DIMENSIONS)	-	500	-
Cl. 8.2(Application of Sheath)	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
5.3(Thickness of Insulation)	-	250	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
9(OVERALL DIMENSIONS)	-	500	-
Cl. 8.2(Application of Sheath)	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
5.3(Thickness of Insulation)	-	250	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
9(OVERALL DIMENSIONS)	-	250	-
Cl. 8.2(Application of Sheath)	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
12(CORE IDENTIFICATION)	-	0	-

13 Dec, 2027

-
Included w.e.f 12.02.2026 Exclusion: Cl 10.3 (Spark Test)

IS 15833 (2009)

Stainless Steel Tower Bolts -specification

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.2(Carbon Content)	-	580	Cl 4.1 Sheet
Clause 4.2(Silicon)	-	570	Cl 4.1 Sheet
Clause 4.2(Manganese)	-	570	Cl 4.1 Sheet
Clause 4.2(nickel)	-	570	Cl 4.1 Sheet
Clause 4.2(Chromium)	-	570	Cl 4.1 Sheet
Clause 4.2(Sulphur)	-	570	Cl 4.1 Sheet
Clause 4.2(Phosphorus)	-	570	Cl 4.1 Sheet
Clause 4.2(Carbon Content)	-	580	Cl 4.2 Bolt
Clause 4.2(Silicon)	-	570	Cl 4.2 Bolt
Clause 4.2(Manganese)	-	570	Cl 4.2 Bolt
Clause 4.2(nickel)	-	570	Cl 4.2 Bolt
Clause 4.2(Chromium)	-	570	Cl 4.2 Bolt
Clause 4.2(Sulphur)	-	570	Cl 4.2 Bolt
Clause 4.2(Phosphorus)	-	570	Cl 4.2 Bolt
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 6(DIMENSIONS)	-	200	-
Cl 3(NOMINAL SIZES)	-	1000	-
Cl 5(MANUFACTURE)	-	1000	-
Cl 7(0)	-	1000	-
8(Marking)	-	1000	-

13 Dec, 2027

-
-

IS 15834 (2020)

Stainless Steel Sliding Door Bolts ( Aldrops ) for Use With Padlocks - Specification ( First Revision )

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
5(DIMENSIONS AND TOLERANCES)	-	150	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	150	-
6(MANUFACTURE)	-	1000	-
7(FINISH)	-	1000	-
8(Marking)	-	1000	-
Cl.4(Carbon)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Sulphur)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Phosphorus)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Manganese)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Silicon)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Nickel)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Chromium)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Copper)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Molybdenum)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Nitrogen)	-	1000	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Titanium)	-	0	Cl 4.1 Sheet & Cl 4.2 Bolt
Cl.4(Niobium)	-	0	Cl 4.1 Sheet & Cl 4.2 Bolt
Sub-Clause. 10.3.3(corrosion resistance)	-	5000	Cl.10.3.3

13 Dec, 2027

-
-

IS 455 (2015)

Portland slag cement - Specification

Portland Slag Cement

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1000	-
7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1000	-
7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1000	-
7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	-
7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	500	-
7 Table 1 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 Table 1 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	500	-
7 Table 1 i(Fineness IS 4031(Part 2))	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	500	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	2000	-

13 Dec, 2027

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Carbon %)	-	400	-
4.1(Manganese %)	-	300	-
4.1(Phosphorus %)	-	400	-
4.1(Sulphur %)	-	400	-
4.1(Silicon %)	-	300	-
4.1( Copper %)	-	300	-
4.1( Nb)	-	300	-
4.1(V)	-	300	-
4.1(Cr)	-	300	-
4.1(Mo)	-	300	-
4.1(Ni)	-	300	-
4.1( Nitrogen%)	-	300	-
4.1(CE)	-	400	-
4.1(Sulphur and phosphorous)	-	400	-
4.2(Boron (B))	-	300	-
Cl 7.2(Weight)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	700	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	700	-
Cl. 8.1 Table 3(Elongation, percentage)	-	700	-
8.18.1 Table 3(Total elongation at maximum force)	-	700	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1500	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	700	-

13 Dec, 2027

-
-

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

PPC(CALCINED CLAY BASED)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	2000	-
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-

13 Dec, 2027

-
-

IS 14543 (2024)

Packaged Drinking Water Other than Packaged Natural Mineral Water Specification Third Revision

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.2.1(Escherichia coli or thermotolerant bacteria)	-	500	-
Cl-5.2.2(Coliform)	-	500	-
Cl-5.2.4(Sulphite Reducing Anaerobes)	-	500	-
Cl-5.2.3(Staphylococcus aureus)	-	500	-
Cl-5.2.5(Pseudomonas Aeruginosa)	-	500	-
Cl-5.2.6(Aerobic Microbial Count @ 37 deg C)	-	500	-
5.2.6(Aerobic Microbial Count @ 20 to 22 deg C)	-	500	-
Cl-5.2.3(Faecal streptococci)	-	500	-
Cl-5.2.9(Vibrio cholera)	-	500	-
Cl-5.2.9(V.parahaemolyticus)	-	500	-
Cl-5.2.8(shigella)	-	500	-
Cl-5.2.8(Salmonella)	-	500	-
Cl-5.2.7(Yeast and mould)	-	500	-
5.3(Appearance)	-	500	-
5.4/Annex D/i(P,P-DDT)	-	500	-
5.4/Annex D/ii(Lindane)	-	500	-
5.4/Annex D/iv(b-Endosulfan)	-	500	-
5.4/Annex D/xvi(Dieldrin)	-	500	-
5.4/Annex D/xvi(Aldrin)	-	500	-
5.4/Annex D/i(O,P-DDT)	-	500	-
5.4/Annex D/iv(a-Endosulfan)	-	500	-
5.4/Annex D/iii(d-HCH)	-	500	-
5.4/Annex D/i(O,P-DDD)	-	500	-
5.4/Annex D/i(P,P-DDE)	-	500	-
5.4/Annex D/i(O,P-DDE)	-	500	-
5.4/Annex D/iii(a-HCH)	-	500	-
5.4/Annex D/iii(β- HCH)	-	500	-
5.4/Annex D/iv(Endosulfan sulfate)	-	500	-
5.4/Annex D/i(P,P-DDD)	-	500	-
5.4/Annex D/xii(Alachlor)	-	500	-
5.4/Annex D/vii(Chlorpyrifos)	-	500	-
5.4/Annex D/x(Butachlor)	-	500	-
5.4/Annex D/vi(Ethion)	-	500	-
5.4/Annex D/xiv(Methyl parathion)	-	500	-
5.4/Annex D/xv(Malathion)	-	500	-
5.4/Annex D/viii(Phorate)	-	500	-
5.4/Annex D/v(Monochrotophos)	-	500	-
5.4/Annex D/xiii(Atrazine)	-	500	-
5.4/Annex D/viii(Phorate sulphoxide)	-	500	-
5.4/Annex D/viii(Phorate sulfone)	-	500	-
5.4/Annex D/xxvii(Methyl paraoxon)	-	500	-
5.4/Annex D/xxviii(Malaoxon)	-	500	-
5.4/Annex D/xi(Isoproturon)	-	500	-
5.4/Annex D/ix(2,4 –D)	-	500	-
Cl-5.3, Table-1 (i)(Colour, true colour units, Max)	-	500	-
Cl-5.3, Table-1 (ii)(Odour)	-	500	-
Cl-5.3, Table-1 (iii)(Taste)	-	500	-
Cl-5.3, Table-1 (iv)(Turbidity, nephelometric turbidity unit (NTU), Max)	-	500	-
Cl-5.3, Table-1 (v)(Total dissolved solids, mg/l, Max)	-	500	-
Cl-5.3, Table-1 (vi)(pH)	-	500	-
Cl-5.3, Table-2 (i)(Barium (as Ba))	-	500	-
Cl-5.3, Table-2 (ii)(Copper (as Cu))	-	500	-
Cl-5.3, Table-2 (iii)(Iron (as Fe))	-	500	-
Cl-5.3, Table-2 (iv)(Manganese (as Mn))	-	500	-
Cl-5.3, Table-2 (v)(Nitrate (as NO3 ))	-	500	-
Cl-5.3, Table-2 (vi)(Nitrite (as NO2 ))	-	500	-
Cl-5.3, Table-2 (vii)(Fluoride (as F))	-	500	-
Cl-5.3, Table-2 (viii)(Zinc (as Zn))	-	500	-
Cl-5.3, Table-2 (ix)(Silver (as Ag))	-	500	-
Cl-5.3, Table-2 (x)(Aluminium (as A1))	-	500	-
Cl-5.3, Table-2 (xi)(Chloride (as Cl))	-	500	-
Cl-5.3, Table-2 (xii)(Selenium (as Se))	-	500	-
Cl-5.3, Table-2 (xiii)(Sulphate (as SO4 ))	-	500	-
Cl-5.3, Table-2 (xiv)(Alkalinity (as HCO3 ))	-	500	-
Cl-5.3, Table-2 (xv)(Calcium (as Ca))	-	500	-
Cl-5.3, Table-2 (xvi)(Magnesium (as Mg))	-	500	-
Cl-5.3, Table-2 (xvii)(Sodium (as Na))	-	500	-
Cl-5.3, Table-2 (xviii)(Residual free chlorine)	-	500	-
Cl-5.3, Table-2 (xix)(Phenolic compounds (as C6H5OH))	-	500	-
Cl-5.3, Table-2 (xx)(Mineral oil)	-	500	-
Cl-5.3, Table-2 (xxi)(Anionic surface active agents)	-	500	-
Cl-5.3, Table-2 (xxii)(Sulphide)	-	500	-
Cl-5.3, Table-2 (xxiii)(Antimony (as Sb))	-	500	-
Cl-5.3, Table-2 (xxiv)(Borates (as B))	-	500	-
Cl-5.3, Table-2 (xxv)(Bromates (as BrO3 ))	-	500	-
Cl-5.3, Table-3 (i)(Mercury (as Hg))	-	500	-
Cl-5.3, Table-3 (ii)(Cadmium (as Cd))	-	500	-
Cl-5.3, Table-3 (iii)(Arsenic (as As))	-	500	-
Cl-5.3, Table-3 (iv)(Cyanide (as CN))	-	500	-
Cl-5.3, Table-3 (v)(Lead (as Pb))	-	500	-
Cl-5.3, Table-3 (vi)(Chromium (as Cr))	-	500	-
Cl-5.3, Table-3 (vii)(Nickel (as Ni))	-	500	-
Cl-5.3, Table-3 (viii)(Polychlorinated biphenyl (PCB))	-	1000	-
Cl-5.3, Table-3 (ix)(Polynuclear aromatic hydrocarbons)	-	1000	-
Cl-5.4 (ii)(Total pesticide residue)	-	5000	-

13 Dec, 2027

-
Exclusion: Cl-5.3, Table-4 (i) (Alpha emitters, Becquerel (Bq/l)), Cl-5.3, Table-4 (ii) (Beta emitters, Becquerel (Bq/l),) Cl-5.3, Table-3 (x) (Uranium)

IS 16415 (2015)

Composite cement - Specification

Composite Cement

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	500	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	1000	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	500	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-

13 Dec, 2027

-
-

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Thickness of sheet/strip)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	500	-
4(Type)	-	1000	-
6.1.2(Thickness of Sheet/Strip)	-	1000	-
Clause no. 6.2(Depth of Bowls)	-	250	-
Clause no. 6.3(Internal dimensions of bowls)	-	500	-
Clause no. 6.4(Bowl Locating Limits)	-	750	-
Clause no. 6.5, Table No. 1(Dimension of the sink)	-	1500	-
7.1(Consruction and workmanship)	-	125	-
7.1.1(Consruction and workmanship)	-	125	-
7.2(Consruction and workmanship)	-	125	-
7.2.1(Consruction and workmanship)	-	125	-
7.3(CONSTRUCTION AND WORKMANSHIP)	-	125	-
7.4(Waste Outlet)	-	125	-
7.5(Tap Holes)	-	125	-
7.6(OVERFLOW)	-	125	-
Clause no. 8(Finish)	-	1000	-
Clause no. 9(Mark)	-	1000	-

13 Dec, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

National Test House (NER) - NTH, Guwahati

C.I.T.I Complex, Post: Gopinath Nagar, Kalapahar, Guwahati-781016, Guwahati, Kamrup Metro, Assam, 781016

9412223452 nthner-ca@gov.in

Scope List