BIS - LIMS (Laboratory Information Management System)

Stellar Test House

G-68, Sector-63, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

8130190099 ankit@stellartesthouse.com

Scope List

Reset

48 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	1500	-
6(Classification)	-	100	-
5(General conditions for the tests)	-	100	-
11.8(Temperature rise)	-	1000	-
11.7(Duration corresponding)	-	100	-
11.6(Combined appliances)	-	100	-
11.5(Motor-operated appliances)	-	100	-
11.4(Heating appliances)	-	100	-
8.1.5(Live parts of built-in appliances)	-	200	-
18(Endurance)	-	100	-
17(Overload protection of transformers and associated circuits)	-	600	-
16(Leakage current and electric strength)	-	500	-
4(General requirement)	-	100	-
32(Radiation Toxicity and Similar Hazards)	-	400	-
31(Resistance to Rusting)	-	500	-
30.2(Needle Flame Test)	-	500	-
30.2(Glow Wire Test)	-	500	-
30.1(Ball pressure test)	-	500	-
29(clearance, creepage distances and solid insulation)	-	500	-
28(Screw test and connections)	-	500	-
27(Provision for earthing)	-	1000	-
26(Terminals for external conductors)	-	500	-
25(Supply connection and external flexible cords)	-	500	-
24(Components)	-	100	-
23(Internal wiring)	-	400	-
22(Construction)	-	500	-
21(Mechanical Strength)	-	100	-
20(Stability and mechanical hazards)	-	1000	-
19(Abnormal Operation)	-	1000	-
18(Endurance)	-	100	-
17(Over Load Protection of Transformers and associated circuits)	-	600	-
16.3(Electric Strength (after clause 15 and 16.2))	-	500	-
16.2(Leakage Current (after Clause 15))	-	100	-
16.1(General)	-	100	-
16.0(General)	-	100	-
15.3(Humidity Test)	-	2000	-
15.2(Spillage Test)	-	300	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	500	-
15.0(Moisture resistance)	-	100	-
14(Transient Over Voltages)	-	400	-
13.3(Electric Strength at operating temperature)	-	500	-
13.2(Leakage current at operating temperature)	-	500	-
13(Leakage current and electric strength at operating temperature)	-	500	-
11.3(Heating)	-	500	-
11.2(General)	-	100	-
11.1(General)	-	100	-
10.2(Current input)	-	100	-
10.1(Power input)	-	100	-
9(Starting of motor operation test requirements and tests)	-	100	-
8.1.4(Protection against live parts against protective impedance)	-	100	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	100	-
8.1.2(Protection against live parts in openings)	-	100	-
8.1.1(Protection against live parts in all positions)	-	100	-
7(Marking and instructions)	-	100	-
A.2(Earth continuity test)	-	100	-
Annex C(Ageing test on motors)	-	100	-
Annex D(Thermal motor protectors)	-	100	-
15.2(Moisture resistance)	-	100	-
19.17(Abnormal operation)	-	100	-
20.1(Stability and mechanical hazards)	-	100	-
21.2(Mechanical strength)	-	100	-
21.3(Mechanical strength)	-	100	-
22.5(Construction)	-	100	-
22.6(Construction)	-	100	-
22.11(Construction)	-	100	-
22.16(Construction)	-	100	-
22.32(Construction)	-	100	-
22.42(Construction)	-	100	-
23.3(Internal wiring)	-	100	-
25(Supply connection and external flexible cords)	-	100	-
25.7(Supply connection and external flexible cords)	-	100	-
25.14(Supply connection and external flexible cords)	-	100	-
25.15(Supply connection and external flexible cords)	-	100	-
26.5(Terminals for external conductors)	-	100	-
27.5(Provision for earthing)	-	100	-
28.1(Screws and connections)	-	100	-
B.22.1(Construction)	-	100	-
B.22.3(Construction)	-	100	-
B.22.4(Construction)	-	100	-
B.22.5(Construction)	-	200	-
12(Charging of metal-ion batteries)	-	1500	-
6(Classification)	-	100	-
5(General conditions for the tests)	-	100	-
11.8(Temperature rise)	-	1000	-
11.7(Duration corresponding)	-	100	-
11.6(Combined appliances)	-	100	-
11.5(Motor-operated appliances)	-	100	-
11.4(Heating appliances)	-	100	-
8.1.5(Live parts of built-in appliances)	-	200	-
18(Endurance)	-	100	-
17(Overload protection of transformers and associated circuits)	-	600	-
16(Leakage current and electric strength)	-	200	-
4(General requirement)	-	100	-
32(Radiation Toxicity and Similar Hazards)	-	200	-
31(Resistance to Rusting)	-	500	-
30.2(Needle Flame Test)	-	500	-
30.2(Glow Wire Test)	-	500	-
30.1(Ball pressure test)	-	500	-
29(clearance, creepage distances and solid insulation)	-	500	-
28(Screw test and connections)	-	400	-
27(Provision for earthing)	-	500	-
26(Terminals for external conductors)	-	200	-
25(Supply connection and external flexible cords)	-	1000	-
24(Components)	-	200	-
23(Internal wiring)	-	500	-
22(Construction)	-	200	-
21(Mechanical Strength)	-	700	-
20(Stability and mechanical hazards)	-	400	-
19(Abnormal Operation)	-	1000	-
18(Endurance)	-	100	-
17(Over Load Protection of Transformers and associated circuits)	-	600	-
16.3(Electric Strength (after clause 15 and 16.2))	-	500	-
16.2(Leakage Current (after Clause 15))	-	500	-
16.1(General)	-	100	-
16.0(General)	-	100	-
15.3(Humidity Test)	-	500	-
15.2(Spillage Test)	-	200	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	200	-
15.0(Moisture resistance)	-	500	-
14(Transient Over Voltages)	-	100	-
13.3(Electric Strength at operating temperature)	-	500	-
13.2(Leakage current at operating temperature)	-	500	-
13(Leakage current and electric strength at operating temperature)	-	500	-
11.3(Heating)	-	1000	-
11.2(General)	-	100	-
11.1(General)	-	100	-
10.2(Current input)	-	500	-
10.1(Power input)	-	500	-
9(Starting of motor operation test requirements and tests)	-	100	-
8.1.4(Protection against live parts against protective impedance)	-	500	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	500	-
8.1.2(Protection against live parts in openings)	-	500	-
8.1.1(Protection against live parts in all positions)	-	500	-
7(Marking and instructions)	-	200	-
A.2(Earth continuity test)	-	400	-
Annex C(Ageing test on motors)	-	200	-
Annex D(Thermal motor protectors)	-	100	-
15.2(Moisture resistance)	-	500	-
19.17(Abnormal operation)	-	1000	-
20.1(Stability and mechanical hazards)	-	500	-
21.2(Mechanical strength)	-	200	-
21.3(Mechanical strength)	-	200	-
22.5(Construction)	-	100	-
22.6(Construction)	-	100	-
22.11(Construction)	-	200	-
22.16(Construction)	-	100	-
22.32(Construction)	-	100	-
22.42(Construction)	-	100	-
23.3(Internal wiring)	-	100	-
25(Supply connection and external flexible cords)	-	100	-
25.7(Supply connection and external flexible cords)	-	500	-
25.14(Supply connection and external flexible cords)	-	100	-
25.15(Supply connection and external flexible cords)	-	100	-
26.5(Terminals for external conductors)	-	500	-
27.5(Provision for earthing)	-	500	-
28.1(Screws and connections)	-	400	-
B.22.1(Construction)	-	200	-
B.22.3(Construction)	-	200	-
B.22.4(Construction)	-	100	-
B.22.5(Construction)	-	100	-

Complete

26 Sep, 2025

-
Included w.e.f 25.03.2025 Exclusion: Cl 19.11.4.1 to Cl 19.11.4.1(EMI/EMC)

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

1151400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	750	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1200	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	65000	-
IS 191 : 2007, IS 440(Copper purity test)	-	4000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	150000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	500	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	7500	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	35000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	250	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	3700	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	3500	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	6000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	3500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	7500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	4000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	500	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	750000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	7500	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	7500	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	1000	-
Annex - B of IS 17293:2020(Compatibility test)	-	7500	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	1000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	2000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	3000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1500	-
Annex - E of IS 17293 : 2020(UV resistance)	-	35000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	5000	-
11.2.5(Surface Resistance of Sheath)	-	4000	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	500	-
Annex J(Assessment of Halogens)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	0	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	0	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
6.2(Sheath application)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	500	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	1500	-
7.1.2.1, 7.2.3(Annealing)	-	500	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	1500	-
5.3(Thickness)	-	500	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	0	-
IS 191 : 2007, IS 440(Copper purity test)	-	0	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	0	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	0	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	0	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	2500	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	2000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1500	-
Annex - E of IS 17293 : 2020(UV resistance)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	3500	-
11.2.5(Surface Resistance of Sheath)	-	3500	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	1000	-
Annex J(Assessment of Halogens)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	2500	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	5000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	2000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	1500	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	2500	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
6.2(Sheath application)	-	0	-
6.3(Sheath Thickness)	-	1000	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	500	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	500	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-
5.3(Thickness)	-	0	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	0	-
IS 191 : 2007, IS 440(Copper purity test)	-	0	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	0	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	0	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	0	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Annex - E of IS 17293 : 2020(UV resistance)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	0	-
11.2.5(Surface Resistance of Sheath)	-	0	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	0	-
Annex J(Assessment of Halogens)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	0	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	0	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
6.2(Sheath application)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	0	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-
5.3(Thickness)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f 02.01.2025 Exclusion : Cl 11.2.2 (Spark Test)

IS 374 (2019)

Specification for electric ceiling type fans and regulators (Third Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	100	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	200	-
8.1,a(Marking )	-	0	-
8.1,b(Marking )	-	0	-
8.1,c(Marking )	-	0	-
8.1,d(Marking )	-	0	-
8.1,e(Marking )	-	0	-
8.1,f(Marking )	-	0	-
8.1,g(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3,a(Marking )	-	0	-
8.3,b(Marking )	-	0	-
8.3,c(Marking )	-	0	-
8.3,d(Marking )	-	0	-
8.3,e(Marking )	-	0	-
8.4(Marking )	-	0	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	0	-
6.2(Rating)	-	200	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	200	-
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	500	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	1000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	500	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	0	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	500	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	1000	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	0	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	500	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	1000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	0	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	0	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	500	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	1000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	0	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	500	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	500	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	0	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	0	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	500	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	0	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	500	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	250	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	500	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	500	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	500	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	0	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	500	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	200	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	0	-
10.1(Speed Regulators)	-	500	-
10.2(Speed Regulators)	-	0	-
10.2(Speed Regulators)	-	0	-
10.2(Speed Regulators)	-	0	-
10.3(Speed Regulators)	-	0	-
10.4(Speed Regulators)	-	0	-
10.5(Speed Regulators)	-	0	-
10.6(Speed Regulators)	-	0	-
10.7(Speed Regulators)	-	0	-
10.7(Speed Regulators)	-	0	-
10.8(Speed Regulators)	-	0	-
11.1(Starting)	-	200	-
11.2(Starting)	-	200	-
12(Interchangeability)	-	200	-
13(Silent Operation)	-	250	-
14.3 & Table 1(Test for Air Performance)	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	0	-
14.4(Measurement of Speed of the Fan )	-	200	-
14.4(Measurement of Speed of the Fan )	-	0	-
14.5(Measurement of Power factor and Power Input)	-	500	-
14.5(Measurement of Power factor and Power Input)	-	0	-
16(Endurance Test)	-	2000	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
17(Test for Harmonic Distortion)	-	500	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	100	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	200	-
8.1,a(Marking )	-	0	-
8.1,b(Marking )	-	0	-
8.1,c(Marking )	-	0	-
8.1,d(Marking )	-	0	-
8.1,e(Marking )	-	0	-
8.1,f(Marking )	-	0	-
8.1,g(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3(Marking )	-	0	-
8.3,a(Marking )	-	0	-
8.3,b(Marking )	-	0	-
8.3,c(Marking )	-	0	-
8.3,d(Marking )	-	0	-
8.3,e(Marking )	-	0	-
8.4(Marking )	-	0	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	0	-
6.2(Rating)	-	200	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	200	-
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	500	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	1000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	0	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	500	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	0	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	500	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	1000	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	0	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	500	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	1000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	0	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	0	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	500	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-1:2008))	-	1000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-1:2008))	-	0	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	500	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	500	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	0	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	0	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	500	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	0	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	500	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	250	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	500	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	0	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	500	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	500	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	0	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	500	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	200	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	0	-
10.1(Speed Regulators)	-	500	-
10.2(Speed Regulators)	-	0	-
10.2(Speed Regulators)	-	0	-
10.2(Speed Regulators)	-	0	-
10.3(Speed Regulators)	-	0	-
10.4(Speed Regulators)	-	0	-
10.5(Speed Regulators)	-	0	-
10.6(Speed Regulators)	-	0	-
10.7(Speed Regulators)	-	0	-
10.7(Speed Regulators)	-	0	-
10.8(Speed Regulators)	-	0	-
11.1(Starting)	-	200	-
11.2(Starting)	-	0	-
12(Interchangeability)	-	200	-
13(Silent Operation)	-	250	-
14.3 & Table 1(Test for Air Performance)	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	0	-
14.4(Measurement of Speed of the Fan )	-	200	-
14.4(Measurement of Speed of the Fan )	-	0	-
14.5(Measurement of Power factor and Power Input)	-	500	-
14.5(Measurement of Power factor and Power Input)	-	0	-
16(Endurance Test)	-	2000	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
16(Endurance Test)	-	0	-
17(Test for Harmonic Distortion)	-	500	-
4(GENERAL REQUIREMENTS)	-	0	-
5(GENERAL NOTES ON TESTS)	-	0	-
15.1, 15.2(Air delivery and service value)	-	2000	-
Cl-9 (Cl-19.11.4.1 of IS 302-1)(Electrostatic discharge)	-	0	-
Cl-9 (Cl-19.11.4.2 of IS 302-1)(Radiated Fields)	-	0	-
Cl-9 (Cl-19.11.4.3 of IS 302-1)(Fast transient bursts)	-	0	-
Cl-9 (Cl-19.11.4.4 of IS 302-1)(Surge Immunity test)	-	0	-
Cl-9 (Cl-19.11.4.5 of IS 302-1)(Immunity to conducted discharge)	-	0	-
Cl-9 (Cl-19.11.4.6 of IS 302-1)(Voltage dips and interruptions)	-	0	-
Cl-9 (Cl-19.11.4.7 of IS 302-1)(Harmonics)	-	0	-
Cl-9 (Cl-19.101 of IS 302-1)(Abnormal Operation)	-	1000	-
(Cl. 17 of IS 302-2-80 :2017)(Overload protection of transformers and associated circuits)	-	500	-
(Cl.4.4 of IS 374: 2019)(Bearings)	-	0	-
(Cl. 4.5 of IS 374: 2019)(Brushless DC Motor)	-	0	-
(Cl.4.6 of IS 374: 2019)(Enclosure)	-	0	-
(Cl. 7.6 of IS 302 Part 1)(Marking and Instructions)	-	200	-
Cl. 7.8 of IS 302-2-80 :2017(MARKING AND INSTRUCTIONS)	-	0	-
(Cl. 7.12 of IS 302-2-80 :2017)(Marking and Instructions)	-	0	-
(Cl. 7.12.1 of IS 302-2-80 :2017)(Marking and Instructions)	-	0	-
(Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions)	-	0	-
(Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions)	-	0	-
(Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions)	-	0	-
(Cl. 7.12.7 of IS 302-1: 2008(Marking and Instructions)	-	0	-
(Cl. 7.13 of IS 302-1: 2008)(Marking and Instructions)	-	0	-
(Cl. 7.14 of IS 302-1: 2008)(Marking and Instructions)	-	0	-
(Cl. 10.1 of IS 374: 2019)(SPEED REGULATORS)	-	500	-
(Cl. 10.3 of IS 374: 2019)(SPEED REGULATORS)	-	0	-
(Cl. 10.4 of IS 374: 2019)(SPEED REGULATORS)	-	0	-
(Cl. 10.7 of IS 374: 2019)(SPEED REGULATORS)	-	0	-
(Cl. 10.7 of IS 374: 2019)(SPEED REGULATORS)	-	0	-
(Cl. 10.8 of IS 374: 2019)(SPEED REGULATORS)	-	0	-
(Cl. 11.2 of IS 374: 2019)(STARTING)	-	200	-
(Cl. 13 of IS 374: 2019)(SILENT OPERATION)	-	250	-
(Cl. 15.1 of IS 374: 2019)(PERFORMANCE REQUIREMENTS)	-	2000	-
(Cl. 15.1 of IS 374: 2019)(PERFORMANCE REQUIREMENTS)	-	0	-
(Cl. 17 of IS 374: 2019(Test for Harmonic Distortion)	-	500	-
(Cl. 8.2 of IS 302-1: 2008)(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	200	-
(Cl. 11 of IS 302-1: 2008)(HEATING)	-	1000	-
(Cl. 15 of IS 302-1: 2008)(MOISTURE RESISTANCE)	-	1000	-
(Cl. 15 of IS 302-1: 2008)(MOISTURE RESISTANCE)	-	0	-
(Cl. 15 of IS 302-1: 2008.(MOISTURE RESISTANCE)	-	0	-
(Cl. 17 of IS 302-1: 2008)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	500	-
(Cl. 17 of IS 302-1: 2008)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	0	-
(Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	1000	-
(Cl. 19.7 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	0	-
(Cl. 19 of IS 302-2-80 :2017)(ABNORMAL OPERATION)	-	0	-
(Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	0	-
(Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	0	-
(Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	0	-
(Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION)	-	0	-
(Cl. 20.102 of IS 302-2-80 :2017)(STABILITY AND MECHANICAL HAZARDS)	-	500	-
(Cl. 22.2 of IS 302-1: 2008)(CONSTRUCTION)	-	500	-
(Cl. 22.14 of IS 302-1: 2008)(CONSTRUCTION)	-	0	-
(Cl. 22.18 of IS 302-1: 2008)(Electric Ceiling type fan-Specification)	-	0	-
(Cl. 22.21 of IS 302-1: 2008)(CONSTRUCTION)	-	500	-
(Cl. 22.22 of IS 302-1: 2008)(CONSTRUCTION)	-	0	-
(Cl. 22.41 of IS 302-1: 2008)(CONSTRUCTION)	-	0	-
(Cl. 22.44 of IS 302-1: 2008)(CONSTRUCTION)	-	0	-
(Cl. 22.101 of IS 302-2-80: 2017)(CONSTRUCTION)	-	0	-
(Cl. 23.1 of IS 302-1: 2008)(INTERNAL WIRING)	-	500	-
(Cl. 23.2 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.4 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.5 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.6 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.7 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.9 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 23.10 of IS 302-1: 2008)(INTERNAL WIRING)	-	0	-
(Cl. 24.1 of IS 302-1: 2008)(COMPONENTS)	-	500	-
(Cl. 24.5 of IS 302-1: 2008)(COMPONENTS)	-	0	-
(Cl. 24.105 of IS IS 302-2-80 :2017)(COMPONENTS)	-	0	-
(Cl. 26.1 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	250	-
(Cl. 26.8 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
(Cl. 26.9 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
(Cl. 26.10 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
(Cl. 27.1 of IS 302-1: 2008)(PROVISION FOR EARTHING)	-	500	-
(Cl. 27.2 of IS 302-1: 2008)(PROVISION FOR EARTHING)	-	0	-
(Cl. 27.4 of IS 302-1: 2008)(PROVISION FOR EARTHING)	-	0	-
(Cl. 27.5 of IS 302-1: 2008)(PROVISION FOR EARTHING)	-	0	-
(Cl. 28.4 of IS 302-1: 2008)(SCREWS AND CONNECTIONS)	-	500	-
(Cl. 30.2 of IS 302-1: 2008)(RESISTANCE TO HEAT AND FIRE)	-	500	-
(Cl. 30.2 of IS 302-1: 2008)(RESISTANCE TO HEAT AND FIRE)	-	500	-
(Cl. 32 of IS 302-1: 2008)(Radiation, toxicity and similar hazards)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f.12.12.2024 exclusion Cl-9 (Cl-19.11.4.1 of IS 302-1) (Electrostatic discharge) Cl-9 (Cl-19.11.4.2 of IS 302-1) (Radiated Fields) Cl-9 (Cl-19.11.4.3 of IS 302-1) (Fast transient bursts) Cl-9 (Cl-19.11.4.4 of IS 302-1) (Surge Immunity test) Cl-9 (Cl-19.11.4.5 of IS 302-1) (Immunity to conducted discharge) Cl-9 (Cl-19.11.4.6 of IS 302-1) (Voltage dips and interruptions) Cl-9 (Cl-19.11.4.7 of IS 302-1) (Harmonics)

IS 302 : Part 2 : Sec 202 (1992)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 202 electric stoves

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	50	5% Discount for BIS
6(Classification- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.3(Marking- IS 302-1)	-	50	5% Discount for BIS
7.4(Marking- IS 302-1)	-	50	5% Discount for BIS
7.6(Marking- IS 302-1)	-	50	5% Discount for BIS
7.11(Marking- IS 302-1)	-	50	5% Discount for BIS
7.12(Marking- IS 302-1)	-	50	5% Discount for BIS
7.13(Marking- IS 302-1)	-	50	5% Discount for BIS
7.14(Marking- IS 302-1)	-	50	5% Discount for BIS
7.15(Marking- IS 302-1)	-	50	5% Discount for BIS
7.101(Marking)	-	50	5% Discount for BIS
8( Protection Against Electric Shock, IS 302-1)	-	400	5% Discount for BIS
10(Power Input and Current, IS 302-1)	-	800	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	200	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
12(Operation under overload conditions of appliances with heating elements, IS 302-2-202: 1992)	-	100	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
15.1(Moisture Resistance, IS 302-1)	-	500	5% Discount for BIS
15.3(Moisture Resistance, IS 302-1)	-	500	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	5% Discount for BIS
21.1(Mechanical Strength, IS 302-1 & IS 302-2-202)	-	500	5% Discount for BIS
22(Construction, IS 302-1)	-	100	5% Discount for BIS
22.101(Construction)	-	100	5% Discount for BIS
22.102(Construction)	-	100	5% Discount for BIS
22.103(Construction)	-	100	5% Discount for BIS
22.104(Construction)	-	100	5% Discount for BIS
22.105(Construction)	-	100	5% Discount for BIS
22.105.1(Construction)	-	100	5% Discount for BIS
22.105.2(Construction)	-	100	5% Discount for BIS
22.106(Construction)	-	100	5% Discount for BIS
11.107.1(Construction)	-	100	5% Discount for BIS
23.1(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.2(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.8(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.9(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.10(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
24.1(Components, IS 302-1)	-	100	5% Discount for BIS
24.2(Components, IS 302-1)	-	100	5% Discount for BIS
24.101(Components)	-	100	5% Discount for BIS
22.107(Construction)	-	100	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.4(Supply Connection and External Flexible Cords)	-	50	5% Discount for BIS
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26(Terminals for External Conductors, IS 302-1)	-	500	5% Discount for BIS
27.1(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.2(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.3(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.4(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.5(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
28(Screws & Connections, IS 302-1)	-	500	5% Discount for BIS
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
31(Resistance of Rusting, IS 302-1)	-	500	5% Discount for BIS
6(Classification- IS 302-1 )	-	50	5% Discount for BIS
6(Classification- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.3(Marking- IS 302-1)	-	50	5% Discount for BIS
7.4(Marking- IS 302-1)	-	50	5% Discount for BIS
7.6(Marking- IS 302-1)	-	50	5% Discount for BIS
7.11(Marking- IS 302-1)	-	50	5% Discount for BIS
7.12(Marking- IS 302-1)	-	50	5% Discount for BIS
7.13(Marking- IS 302-1)	-	50	5% Discount for BIS
7.14(Marking- IS 302-1)	-	50	5% Discount for BIS
7.15(Marking- IS 302-1)	-	50	5% Discount for BIS
7.101(Marking)	-	50	5% Discount for BIS
8( Protection Against Electric Shock, IS 302-1)	-	400	5% Discount for BIS
10(Power Input and Current, IS 302-1)	-	800	5% Discount for BIS
11(Heating, IS 302-1)	-	200	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
12(Operation under overload conditions of appliances with heating elements, IS 302-2-202: 1992)	-	100	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
15.1(Moisture Resistance, IS 302-1)	-	1000	5% Discount for BIS
15.3(Moisture Resistance, IS 302-1)	-	1000	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	500	5% Discount for BIS
21.1(Mechanical Strength, IS 302-1 & IS 302-2-202)	-	500	5% Discount for BIS
22(Construction, IS 302-1)	-	100	5% Discount for BIS
22.101(Construction)	-	100	5% Discount for BIS
22.102(Construction)	-	100	5% Discount for BIS
22.103(Construction)	-	100	5% Discount for BIS
22.104(Construction)	-	100	5% Discount for BIS
22.105(Construction)	-	100	5% Discount for BIS
22.105.1(Construction)	-	100	5% Discount for BIS
22.105.2(Construction)	-	100	5% Discount for BIS
22.106(Construction)	-	100	5% Discount for BIS
11.107.1(Construction)	-	100	5% Discount for BIS
23.1(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.2(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.8(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.9(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.10(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
24.1(Components, IS 302-1)	-	100	5% Discount for BIS
24.2(Components, IS 302-1)	-	100	5% Discount for BIS
24.101(Components)	-	100	5% Discount for BIS
22.107(Construction)	-	100	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.4(Supply Connection and External Flexible Cords)	-	50	5% Discount for BIS
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	500	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26(Terminals for External Conductors, IS 302-1)	-	500	5% Discount for BIS
27.1(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.2(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.3(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.4(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.5(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
28(Screws & Connections, IS 302-1)	-	500	5% Discount for BIS
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
31(Resistance of Rusting, IS 302-1)	-	500	5% Discount for BIS
6(Classification- IS 302-1 )	-	50	5% Discount for BIS
6(Classification- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.1(Marking- IS 302-1)	-	50	5% Discount for BIS
7.3(Marking- IS 302-1)	-	50	5% Discount for BIS
7.4(Marking- IS 302-1)	-	50	5% Discount for BIS
7.6(Marking- IS 302-1)	-	50	5% Discount for BIS
7.11(Marking- IS 302-1)	-	50	5% Discount for BIS
7.12(Marking- IS 302-1)	-	50	5% Discount for BIS
7.13(Marking- IS 302-1)	-	50	5% Discount for BIS
7.14(Marking- IS 302-1)	-	50	5% Discount for BIS
7.15(Marking- IS 302-1)	-	50	5% Discount for BIS
7.101(Marking)	-	50	5% Discount for BIS
8( Protection Against Electric Shock, IS 302-1)	-	400	5% Discount for BIS
10(Power Input and Current, IS 302-1)	-	800	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
11(Heating, IS 302-1)	-	100	5% Discount for BIS
12(Operation under overload conditions of appliances with heating elements, IS 302-2-202: 1992)	-	100	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
15.1(Moisture Resistance, IS 302-1)	-	500	5% Discount for BIS
15.3(Moisture Resistance, IS 302-1)	-	500	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	250	5% Discount for BIS
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.2(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
19.3(Abnormal Operation, IS 302-1)	-	250	5% Discount for BIS
20.1(Stability & Mechanical Hazards, IS 302-1)	-	250	5% Discount for BIS
21.1(Mechanical Strength, IS 302-1 & IS 302-2-202)	-	500	5% Discount for BIS
22(Construction, IS 302-1)	-	100	5% Discount for BIS
22.101(Construction)	-	100	5% Discount for BIS
22.102(Construction)	-	100	5% Discount for BIS
22.103(Construction)	-	100	5% Discount for BIS
22.104(Construction)	-	100	5% Discount for BIS
22.105(Construction)	-	100	5% Discount for BIS
22.105.1(Construction)	-	100	5% Discount for BIS
22.105.2(Construction)	-	100	5% Discount for BIS
22.106(Construction)	-	100	5% Discount for BIS
11.107.1(Construction)	-	100	5% Discount for BIS
23.1(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.2(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.8(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.9(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
23.10(Internal Wiring, IS 302-1)	-	100	5% Discount for BIS
24.1(Components, IS 302-1)	-	100	5% Discount for BIS
24.2(Components, IS 302-1)	-	100	5% Discount for BIS
24.101(Components)	-	100	5% Discount for BIS
22.107(Construction)	-	100	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.4(Supply Connection and External Flexible Cords)	-	50	5% Discount for BIS
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	500	5% Discount for BIS
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	5% Discount for BIS
26(Terminals for External Conductors, IS 302-1)	-	50	5% Discount for BIS
27.1(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.2(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.3(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.4(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
27.5(Provision for Earthing, IS 302-1)	-	100	5% Discount for BIS
28(Screws & Connections, IS 302-1)	-	500	5% Discount for BIS
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	5% Discount for BIS
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	500	5% Discount for BIS
31(Resistance of Rusting, IS 302-1)	-	500	5% Discount for BIS

Complete

26 Sep, 2025

-
Included w.e.f.12.12.2024 Exclusion Cl 24, CL 22, (EMI/EMC) 19.11.4.1 to 19.11.4.7

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(RATINGS)	-	20	5% discount for BIS
7.1.1(Accessories Classification)	-	20	5% discount for BIS
7.1.2(Accessories Classification)	-	20	5% discount for BIS
7.1.3(Accessories Classification)	-	20	5% discount for BIS
7.1.4(Accessories Classification)	-	20	5% discount for BIS
7.1.5(Accessories Classification)	-	20	5% discount for BIS
7.2.1(Socket-Outlets Classification)	-	20	5% discount for BIS
7.2.2(Socket-Outlets Classification)	-	20	5% discount for BIS
7.2.3(Socket-Outlets Classification)	-	20	5% discount for BIS
7.2.4(Socket-Outlets Classification)	-	20	5% discount for BIS
7.3(Plug Classification)	-	20	5% discount for BIS
8(Marking)	-	20	5% discount for BIS
9(CHECKING OF DIMENSIONS)	-	50	5% discount for BIS
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	50	5% discount for BIS
11(Provision for earthing)	-	50	5% discount for BIS
12(terminals)	-	50	5% discount for BIS
13.1(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.2(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.3(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.4(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.5(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.6(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.7(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.8(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.9(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.10(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.11(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.12(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.13(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.14(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.15(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.16(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.17(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.18(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.19(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.2(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.21(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.22(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
13.23(Construction of fixed Socket Outlets)	-	50	5% discount for BIS
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.10(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.20(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
14.26(CONSTRUCTION OF PLUGS AND PORTABLE SOCKETOUTLET)	-	50	5% discount for BIS
15(INTERLOCKED SOCKET-OUTLETS)	-	50	5% discount for BIS
16.1(Resistance to Ageing)	-	250	5% discount for BIS
16.2(RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	260	5% discount for BIS
16.3(Resistance to Humidity)	-	250	5% discount for BIS
17.1(RESISTANCE AND ELECTRIC STRENGTH)	-	200	5% discount for BIS
17.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	200	5% discount for BIS
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	200	5% discount for BIS
18(OPERATION OF EARTHING CONTACTS)	-	100	5% discount for BIS
19(TEMPERATURE RISE)	-	300	5% discount for BIS
20(Making & Breaking Capacity)	-	400	5% discount for BIS
21(Normal Operation)	-	400	5% discount for BIS
22.1(Verification of the Maximum Withdrawal Force)	-	50	5% discount for BIS
22.2(Verification of Minimum Withdrawal Force)	-	50	5% discount for BIS
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	50	5% discount for BIS
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	50	5% discount for BIS
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	50	5% discount for BIS
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	50	5% discount for BIS
24.1(MECHANICAL STRENGTH For all kinds of fixed socketoutlets)	-	200	5% discount for BIS
24.1(MECHANICAL STRENGTH For portable multiple and combined socket outlets with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.1(MECHANICAL STRENGTH For surface mounting boxes)	-	200	5% discount for BIS
24.2(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.2(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.3(MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-	200	5% discount for BIS
24.4(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.4(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.5(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.5(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.5(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	5% discount for BIS
24.6(MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-	200	5% discount for BIS
24.7(MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-	200	5% discount for BIS
24.8(MECHANICAL STRENGTH For shuttered socketoutlets)	-	200	5% discount for BIS
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.10(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.10(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	200	5% discount for BIS
24.11(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	200	5% discount for BIS
24.12(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	200	5% discount for BIS
24.13(MECHANICAL STRENGTH For portable socketoutlets having means for suspension on a wall)	-	200	5% discount for BIS
24.14.1(MECHANICAL STRENGTH For fixed socket-outlets)	-	200	5% discount for BIS
24.14.2(MECHANICAL STRENGTH For fixed socket-outlets)	-	200	5% discount for BIS
24.14.3(MECHANICAL STRENGTH For plugs and portable socketoutlets)	-	200	5% discount for BIS
24.15(MECHANICAL STRENGTH)	-	200	5% discount for BIS
24.16(MECHANICAL STRENGTH)	-	200	5% discount for BIS
24.16(MECHANICAL STRENGTH For shroud of portable socket-outlets)	-	200	5% discount for BIS
25.1(Resistance to heat)	-	200	5% discount for BIS
25.2(Resistance to heat)	-	200	5% discount for BIS
25.3(Resistance to heat)	-	200	5% discount for BIS
25.4(Resistance to heat)	-	200	5% discount for BIS
26.1(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.2(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.3(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.4(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.5(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.6(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
26.7(SCREWS, CURRENTCARRYING PARTS AND CONNECTIONS)	-	100	5% discount for BIS
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	50	5% discount for BIS
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	5% discount for BIS
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	5% discount for BIS
28.1.1(Glow-Wire Test)	-	200	5% discount for BIS
28.2(Resistance to Tracking)	-	200	5% discount for BIS
29(Resistance to Rusting)	-	200	5% discount for BIS
30.1(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-	200	5% discount for BIS
30.2(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-	200	5% discount for BIS
30.3(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-	200	5% discount for BIS
30.4(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-	200	5% discount for BIS

Complete

26 Sep, 2025

-
included w.e.f.01.11.2024

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	500	5% discount BIS
6.0(Marking)	-	500	5% discount BIS
7.0(Construction)	-	1000	5% discount BIS
8.0(Creepage Distance and Clearances)	-	1000	5% discount BIS
9.0(Provision for earthing)	-	800	5% discount BIS
10.0(Terminals)	-	700	5% discount BIS
11.0(External & Internal Wiring)	-	1000	5% discount BIS
12.0(Protection against electric shock)	-	2000	5% discount BIS
13.0(Endurance Tests and Thermal Tests)	-	6000	5% discount BIS
14.0(Resistance to Dust & Moisture)	-	2000	5% discount BIS
15.0(Insulation Resistance and Electric Strength)	-	4000	5% discount BIS
16.0(Resistance to Heat , fire and tracking)	-	3000	5% discount BIS
17.0(Photometric Test)	-	0	-
(Cl.4.24) (Annex-P)(UV Radiations for metal halide lamps)	-	0	-
4.26.2(Short Circuit Protection)	-	0	-

Complete

26 Sep, 2025

-
included.w.e.f.17.10.2024 Exclusion CL 17.0 (Photometric Test) (Cl.4.24) (Annex-P) (UV Radiations for metal halide lamps) CL 4.26.2 (Short Circuit Protection)

IS 4159 (2021)

Mineral Filled Sheathed Heating Elements

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
"Cl. 6 IS 4159:2021"(Classification)	-	200	(5% discount for BIS)
"Cl. 8 IS 4159:2021"(Protection against access to live parts)	-	600	(5% discount for BIS)
"Cl. 9 IS 4159:2021"(Starting of motor operated appliances)	-	0	(5% discount for BIS)
"Cl. 10 IS 4159:2021"(Power Input and Current)	-	500	(5% discount for BIS)
"Cl. 11 IS 4159:2021"(Heating)	-	1000	(5% discount for BIS)
"Cl. 13 IS 4159:2021"(Leakage Current & Electrical Strength at Operating Temperature)	-	500	(5% discount for BIS)
"Cl. 14 IS 4159:2021"(Transient Over Voltage)	-	200	(5% discount for BIS)
"Cl. 15 IS 4159:2021"(Moisture Resistance)	-	1000	(5% discount for BIS)
"Cl. 16 IS 4159:2021"(Leakage Current and Electric strength)	-	800	(5% discount for BIS)
"Cl. 17 IS 4159:2021"(Overload protection of transformers and associated circuits.)	-	200	(5% discount for BIS)
"Cl. 18 IS 4159:2021"(Endurance)	-	1200	(5% discount for BIS)
"Cl. 19 IS 4159:2021"(Abnormal Operation)	-	500	(5% discount for BIS)
"Cl. 20 IS 4159:2021"(Stability and mechanical Hazards)	-	0	(5% discount for BIS)
"Cl. 21 IS 4159:2021"(Mechanical Strength)	-	300	(5% discount for BIS)
"Cl. 22 IS 4159:2021"(Construction)	-	200	(5% discount for BIS)
"Cl. 23 IS 4159:2021"(Internal Wiring)	-	200	(5% discount for BIS)
"Cl. 24 IS 4159:2021"(Components)	-	200	(5% discount for BIS)
"Cl. 25 IS 4159:2021"(Supply Connections and External Flexible Cables and Cords)	-	200	(5% discount for BIS)
"Cl. 26 IS 4159:2021"(Terminal For External Conductors)	-	200	(5% discount for BIS)
"Cl. 27 IS 4159:2021"(Provision For Earthing)	-	100	(5% discount for BIS)
"Cl. 28 IS 4159:2021"(Screws and Connections)	-	200	(5% discount for BIS)
"Cl. 29 IS 4159:2021"(Creepage Distances, Clearances And Distances Through Insulation)	-	200	(5% discount for BIS)
"Cl. 30 IS 4159:2021"(Resistance To Heat, Fire And Tracking)	-	500	(5% discount for BIS)
"Cl. 31 IS 4159:2021"(Resistance To Rusting)	-	300	(5% discount for BIS)
"Cl. 102 IS 4159:2021"(Leakage and hydrostatic strength (for oil heating elements))	-	500	(5% discount for BIS)
Cl.22.106(CONSTRUCTION)	-	200	(5% discount for BIS)
"Cl. 6 IS 4159:2021"(Classification)	-	200	(5% discount for BIS)
"Cl. 8 IS 4159:2021"(Protection against access to live parts)	-	600	(5% discount for BIS)
"Cl. 9 IS 4159:2021"(Starting of motor operated appliances)	-	0	(5% discount for BIS)
"Cl. 10 IS 4159:2021"(Power Input and Current)	-	500	(5% discount for BIS)
"Cl. 11 IS 4159:2021"(Heating)	-	1000	(5% discount for BIS)
"Cl. 13 IS 4159:2021"(Leakage Current & Electrical Strength at Operating Temperature)	-	500	(5% discount for BIS)
"Cl. 14 IS 4159:2021"(Transient Over Voltage)	-	200	(5% discount for BIS)
"Cl. 15 IS 4159:2021"(Moisture Resistance)	-	1000	(5% discount for BIS)
"Cl. 16 IS 4159:2021"(Leakage Current and Electric strength)	-	800	(5% discount for BIS)
"Cl. 17 IS 4159:2021"(Overload protection of transformers and associated circuits.)	-	200	(5% discount for BIS)
"Cl. 18 IS 4159:2021"(Endurance)	-	1200	(5% discount for BIS)
"Cl. 19 IS 4159:2021"(Abnormal Operation)	-	500	(5% discount for BIS)
"Cl. 20 IS 4159:2021"(Stability and mechanical Hazards)	-	0	(5% discount for BIS)
"Cl. 21 IS 4159:2021"(Mechanical Strength)	-	300	(5% discount for BIS)
"Cl. 22 IS 4159:2021"(Construction)	-	200	(5% discount for BIS)
"Cl. 23 IS 4159:2021"(Internal Wiring)	-	200	(5% discount for BIS)
"Cl. 24 IS 4159:2021"(Components)	-	200	(5% discount for BIS)
"Cl. 25 IS 4159:2021"(Supply Connections and External Flexible Cables and Cords)	-	200	(5% discount for BIS)
"Cl. 26 IS 4159:2021"(Terminal For External Conductors)	-	200	(5% discount for BIS)
"Cl. 27 IS 4159:2021"(Provision For Earthing)	-	100	(5% discount for BIS)
"Cl. 28 IS 4159:2021"(Screws and Connections)	-	200	(5% discount for BIS)
"Cl. 29 IS 4159:2021"(Creepage Distances, Clearances And Distances Through Insulation)	-	200	(5% discount for BIS)
"Cl. 30 IS 4159:2021"(Resistance To Heat, Fire And Tracking)	-	500	(5% discount for BIS)
"Cl. 31 IS 4159:2021"(Resistance To Rusting)	-	300	(5% discount for BIS)
"Cl. 102 IS 4159:2021"(Leakage and hydrostatic strength (for oil heating elements))	-	500	(5% discount for BIS)
Cl.22.106(CONSTRUCTION)	-	200	(5% discount for BIS)
"Cl. 6 IS 4159:2021"(Classification)	-	200	(5% discount for BIS)
"Cl. 8 IS 4159:2021"(Protection against access to live parts)	-	600	(5% discount for BIS)
"Cl. 9 IS 4159:2021"(Starting of motor operated appliances)	-	0	(5% discount for BIS)
"Cl. 10 IS 4159:2021"(Power Input and Current)	-	500	(5% discount for BIS)
"Cl. 11 IS 4159:2021"(Heating)	-	1000	(5% discount for BIS)
"Cl. 13 IS 4159:2021"(Leakage Current & Electrical Strength at Operating Temperature)	-	500	(5% discount for BIS)
"Cl. 14 IS 4159:2021"(Transient Over Voltage)	-	200	(5% discount for BIS)
"Cl. 15 IS 4159:2021"(Moisture Resistance)	-	1000	(5% discount for BIS)
"Cl. 16 IS 4159:2021"(Leakage Current and Electric strength)	-	800	(5% discount for BIS)
"Cl. 17 IS 4159:2021"(Overload protection of transformers and associated circuits.)	-	200	(5% discount for BIS)
"Cl. 18 IS 4159:2021"(Endurance)	-	1200	(5% discount for BIS)
"Cl. 19 IS 4159:2021"(Abnormal Operation)	-	500	(5% discount for BIS)
"Cl. 20 IS 4159:2021"(Stability and mechanical Hazards)	-	0	(5% discount for BIS)
"Cl. 21 IS 4159:2021"(Mechanical Strength)	-	300	(5% discount for BIS)
"Cl. 22 IS 4159:2021"(Construction)	-	200	(5% discount for BIS)
"Cl. 23 IS 4159:2021"(Internal Wiring)	-	200	(5% discount for BIS)
"Cl. 24 IS 4159:2021"(Components)	-	200	(5% discount for BIS)
"Cl. 25 IS 4159:2021"(Supply Connections and External Flexible Cables and Cords)	-	200	(5% discount for BIS)
"Cl. 26 IS 4159:2021"(Terminal For External Conductors)	-	200	(5% discount for BIS)
"Cl. 27 IS 4159:2021"(Provision For Earthing)	-	100	(5% discount for BIS)
"Cl. 28 IS 4159:2021"(Screws and Connections)	-	200	(5% discount for BIS)
"Cl. 29 IS 4159:2021"(Creepage Distances, Clearances And Distances Through Insulation)	-	200	(5% discount for BIS)
"Cl. 30 IS 4159:2021"(Resistance To Heat, Fire And Tracking)	-	500	(5% discount for BIS)
"Cl. 31 IS 4159:2021"(Resistance To Rusting)	-	300	(5% discount for BIS)
"Cl. 102 IS 4159:2021"(Leakage and hydrostatic strength (for oil heating elements))	-	500	(5% discount for BIS)
Cl.22.106(CONSTRUCTION)	-	200	(5% discount for BIS)
Cl.7.1 of IS 4159:2021(Marking)	-	500	(5% discount for BIS)
Cl.7.1 of IS 4159:2021(Marking)	-	0	-
Cl.7.1 of IS 4159:2021(Marking)	-	0	-
Cl.7.1 of IS 4159:2021(Marking)	-	0	-
Cl.7.1 of IS 4159:2021(Marking)	-	0	-
Cl.7.1 of IS 4159:2021(Marking)	-	0	-
Cl.7.2 of IS 4159:2021(Marking)	-	0	-
Cl.7.3 of IS 4159:2021(Marking)	-	0	-
Cl.10 of IS 302-1:2008(Power Input & Current)	-	500	(5% discount for BIS)
Cl.11 of IS 4159:2021 & IS 302‐1:2008(Heating)	-	1000	(5% discount for BIS)
Cl.11 of IS 4159:2021 & IS 302‐1:2008(Heating)	-	0	(5% discount for BIS)
Cl.11.2 of IS 4159:2021(Heating)	-	0	(5% discount for BIS)
Cl.11.101 of IS 4159:2021(Heating)	-	100	(5% discount for BIS)
Cl.18 of IS 4159:2021(Endurance Test)	-	1200	(5% discount for BIS)
Cl.19.2 of IS 302-1: 2008(Abnormal Operation)	-	500	(5% discount for BIS)
Cl.19.3 of IS 302-1: 2008(Abnormal Operation)	-	0	-
Cl.19.13 IS 302-1: 2008(Abnormal Operation)	-	0	-
Cl.19.13 IS 302-1: 2008(Abnormal Operation)	-	500	(5% discount for BIS)
Cl.19.13 IS 302-1: 2008(Abnormal Operation)	-	0	-
Cl.22.101 of IS 4159:2021(Construction)	-	200	(5% discount for BIS)
Cl.22.102 of IS 4159:2021(Construction)	-	0	-
Cl.22.103 of IS 4159:2021(Construction)	-	0	-
Cl.22.104 of IS 4159:2021(Construction)	-	0	-
Cl.22.105 of IS 4159:2021(Construction)	-	0	-
Cl.22.106 of IS 4159:2021(Construction)	-	200	(5% discount for BIS)
Cl.22.107 of IS 4159:2021(Construction)	-	0	-
Cl.22.108 of IS 4159:2021(Construction)	-	0	-
Cl.22.109 of IS 4159:2021(Construction)	-	0	-
Cl.22.110 of IS 4159:2021(Construction)	-	0	-
Cl.22.111 of IS 4159:2021(Construction)	-	0	-
Cl.27 & IS 302-1: 2008(Provision for Earthing)	-	100	(5% discount for BIS)
Cl.27 & IS 302-1: 2008(Provision for Earthing)	-	100	(5% discount for BIS)
Cl.28.1 & IS 302-1: 2008(Screws & Connection)	-	200	(5% discount for BIS)
Cl.28.4 IS 302-1: 2008(Screws & Connection)	-	200	(5% discount for BIS)
Cl. 29.1 & IS 302-1: 2008(Creepage Distances & Clearances)	-	200	(5% discount for BIS)
Cl. 29.2 & IS 302-1: 2009(Creepage Distances & Clearances)	-	200	(5% discount for BIS)

Complete

26 Sep, 2025

-
-

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

23000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	200	-
6(Interchangeability)	-	800	-
7(Protection against accidental contact with live parts)	-	500	-
8(Insulation Resistance and Electric Strength)	-	2000	-
9(MECHANICAL STRENGTH)	-	800	-
10(cap temperature)	-	2000	-
11(Resistance to Heat)	-	800	-
12(Resistance to Flame and Ignition)	-	2000	-
13(Fault conditions)	-	800	-
14(Creepage distance and clearances)	-	500	-
4(General requirement and General test requirements)	-	500	-
5(Marking)	-	200	-
6(Interchangeability)	-	800	-
7(Protection against accidental contact with live parts)	-	500	-
8(Strength after humidity treatment)	-	800	-
9(Mechanical strength)	-	800	-
10(Cap temperature rise)	-	2000	-
11(Resistance to heat)	-	800	-
12(Resistance to flame and ignition)	-	2000	-
13(Fault conditions)	-	800	-
14(Creepage distances and clearances)	-	500	-
15(Selection of lamps for tests (Sampling))	-	500	-
16(Condition of compliance)	-	500	-
17(Tests)	-	400	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	500	-
Annex B(Lamps with operating position limitations)	-	500	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	500	-

Complete

26 Sep, 2025

-
included.w.e.f.17.10.2024

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

10900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	100	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	100	-
5.1(Insulation)	-	100	-
6.1(Flexibility class)	-	100	-
6.2(Compactness)	-	100	-
6.2(No of strands)	-	100	-
6.2(Surface)	-	100	-
6.3(Protective barrier)	-	100	-
6.4(size of street lighting conductor)	-	100	-
6.5(Size of messenger conductor )	-	100	-
6.6(Joints in messenger conductor )	-	100	-
6.6(Direction of outer layer)	-	100	-
7.1(Insulation)	-	100	-
7.2( Thickness of insulation)	-	100	-
7.3(Tolerance on thickness of insulation )	-	100	-
7.4(Aplication of the insulation )	-	100	-
7.5(Colour of the insulation )	-	100	-
8.1(Core identification)	-	100	-
8.2(Core identification)	-	100	-
8.3(Identification by other means)	-	100	-
9.1(Assembly (Laying up))	-	200	-
9.2(Assembly (Laying up))	-	100	-
9.3(Direction of lay)	-	200	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	400	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	400	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	400	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	400	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	400	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	200	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	200	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	200	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	200	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	200	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	200	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	200	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	200	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	400	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	400	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	400	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	400	-
10.1 g)(High voltage test - IS10810:Part 45)	-	400	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	400	-
11.4(Bending Test on the Completed Cable ( Optional))	-	400	-
10.1 d) iii)(Carbon Black Content)	-	500	-

Complete

26 Sep, 2025

-
including w.e.f 09.10.2024

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

134000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	2000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1500	-
IS 191:2007 & IS 440(Copper purity test)	-	3500	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	3000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	2000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	3000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	4000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	3000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	3000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	3000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	3000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	1000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	1500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	1500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	1500	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	300	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	3000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	3000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	1000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	1500	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	3000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	3000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	3000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	3000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	3000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	1500	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	3000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	3000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	3000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	3000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	3000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	3000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	3000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	3000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	3000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	3000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	3000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	3000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	3000	-

Complete

26 Sep, 2025

-
including w.e.f 09.10.2024

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

120850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	300	-
4.1.1 b) (Material : Seperator tape )	-	300	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	300	-
4.1.1 e) (Shape of conductor )	-	300	-
4.1.1 f) (Nominal size of conductor )	-	300	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	300	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	300	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	500	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	500	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	800	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	500	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	800	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	500	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	500	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	500	-
4.3(Fillers)	-	300	-
4.4(Binder Tape)	-	300	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	300	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	300	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	500	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	500	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	500	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	500	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	800	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	800	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	500	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	500	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	800	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	300	-
4.5.6, 13.4(Colour of Sheath)	-	300	-
5.1(High Voltage Test (at Room Temperature))	-	1500	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	2000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	2000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	2500	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	2500	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	10000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	1000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	2000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	2000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	2000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	2000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	2000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	2000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	2000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	2000	-
6.1, Table 1(CORE IDENTIFICATION)	-	300	-
6.2(Core Identification by Numbers)	-	300	-
6.2.1(Preferred Arrangement of Marking)	-	300	-
6.2.2(Durability)	-	300	-
7.0(CABLE CODE)	-	300	-
9.0( IDENTIFICATION)	-	300	-
10.1(Packing )	-	300	-
10.2(marking)	-	300	-
10.2.1(Standards marking)	-	300	-
13.3, 14.3(assembly of cores )	-	300	-
6.1(General Requirements)	-	300	-
6.1.1(Colour Combination Green Yellow)	-	300	-
12.1(Conductor)	-	300	-
12.2, Table 4(insulation)	-	300	-
Table 4(Copper Purity test)	-	3500	-
4.3.1 (e)(Fluorine content test (Fillers))	-	1000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	1000	-
4.3.1 (c)(Conductivity test (Fillers))	-	1000	-
4.3.1 (b)(pH test (Fillers))	-	1000	-
4.3.1 (a)(HCl test (Fillers))	-	1000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	1000	-
5.7 (b)(pH test (Assessment of halogen test))	-	1000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	1000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	1000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	1000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	3500	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	2000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	4500	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	4500	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	3500	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1500	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1500	-

Complete

26 Sep, 2025

-
including w.e.f.10.10.2024 exclusion: cl 5.2 (spark test (route test)

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

Insulating materials &insulators

3600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	200	-
10.a)(Packing)	-	200	-
10.b)(Packing)	-	200	-
10.c)(Packing)	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	200	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	200	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	300	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	200	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	2000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	200	-
10(Packing)	-	200	-
10(Packing)	-	200	-
10(Packing)	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	200	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	300	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	200	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	2000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	200	-
10.a)(Packing)	-	200	-
10.b)(Packing)	-	200	-
10.c)(Packing)	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	200	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	300	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	200	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	2000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	200	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	200	-
10(Packing)	-	200	-
10(Packing)	-	200	-
10(Packing)	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	200	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	200	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	300	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	300	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	200	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	800	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	2000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Thermal Properties (Cl..8.4))	-	1000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-

Complete

26 Sep, 2025

-
Included w.e.f 06.12.2024

IS 9103 (1999)

Specification for Concrete Admixtures -

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 9, Table- 2(Dry material content )	-	500	-
Clause 9, Table- 2(Ash content)	-	500	-
Clause 9, Table- 2(Relative density)	-	300	-
Clause 9, Table- 2(Chloride ion content)	-	800	-
Clause 9, Table- 2( pH)	-	500	-
Clause 9, Table- 2(Dry material content )	-	500	-
Clause 9, Table- 2(Ash content)	-	500	-
Clause 9, Table- 2(Relative density)	-	300	-
Clause 9, Table- 2(Chloride ion content)	-	800	-
Clause 9, Table- 2( pH)	-	500	-
Cl 4, Table 1A(Slump)	-	1000	-
Cl 4, Table 1 B(Flow, Loss of workability on satnding, Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	1000	-
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	500	-
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	1000	-
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	2000	-
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	2000	-
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	1500	-
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	1000	-
Cl 4, Table 1A(Loss of workability)	-	1500	-
Cl 4, Table 1A(Air content (%), Max, over control)	-	1000	-
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	1500	-
Clause 4, Table 1B, SI no. (iii) (1 year minimum compressive strength, percent of control mix concrete)	-	1500	-
Clause 4, Table 1B, SI no. (iii) (6 months minimum compressive strength, percent of control mix concrete)	-	1500	-
Clause 4, Table 1B, SI no. (iii) (7 days minimum compressive strength, percent of control mix concrete)	-	1500	-
Clause 4, Table 1A, SI no. (v) (28 days flexural strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (v) (7 days flexural strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (v) (3 days flexural strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (iv) (1 year compressive strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (iv) (6 months compressive strength, percent of control sample)	-	2000	-
Clause 4, Table 1A, SI no. (iv) (28 days compressive strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (iv) (7 days compressive strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (iv) (3 days compressive strength, percent of control sample)	-	1500	-
Clause 4, Table 1A, SI no. (iv) (1 day compressive strength, percent of control sample)	-	1000	-
Clause 4, Table 1A, SI no. (iii) (Final time of setting allowable deviation from control sample)	-	1000	-
Clause 4, Table 1A, SI no. (iii) (Initial time of setting allowable deviation from control sample)	-	1000	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	1500	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	1500	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	1500	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 7 days)	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	1500	-
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	1500	-
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	1000	-
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	1000	-
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	1000	-
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	1500	-
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	1500	-
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	1500	-
Cl 9 Table 2(Dry material content ( a-For liquid admixture, b- For solid admixture), Ash content, Relative density, Chloride ion content, pH)	-	500	-
Cl 9 Table 2(Dry material content ( a-For liquid admixture, b- For solid admixture), Ash content, Relative density, Chloride ion content, pH)	-	500	-
Cl 4, Table 1 B(Flow)	-	1000	-
Cl 4, Table 1 B(Loss of workability on standing)	-	1000	-
Clause 4, Table 1B, SI no. (iii) (28 days minimum compressive strength, percent of control mix concrete)	-	1500	-
Clause 9, Table- 2(Dry material content )	-	0	-
Clause 9, Table- 2(Ash content)	-	0	-
Clause 9, Table- 2(Relative density)	-	0	-
Clause 9, Table- 2(Chloride ion content)	-	0	-
Clause 9, Table- 2( pH)	-	0	-
Clause 9, Table- 2(Dry material content )	-	0	-
Clause 9, Table- 2(Ash content)	-	0	-
Clause 9, Table- 2(Relative density)	-	0	-
Clause 9, Table- 2(Chloride ion content)	-	0	-
Clause 9, Table- 2( pH)	-	0	-
Cl 4, Table 1A(Slump)	-	0	-
Cl 4, Table 1 B(Flow, Loss of workability on satnding, Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	0	-
Cl 4, Table 1A(Water Content, percent of control sample, Max)	-	0	-
Cl 4, Table 1A(Time of setting, allowable deviation from control sample hours)	-	0	-
Cl 4, Table 1A(Compressive strength, percent of control sample, Min)	-	0	-
Cl 4, Table 1A(Flexural strength, percent of control sample, Min)	-	0	-
Cl 4, Table 1A(Length change, percent increase over control sample, Max)	-	0	-
Cl 4, Table 1A(Bleeding, percent increase over control sample, Max)	-	0	-
Cl 4, Table 1A(Loss of workability)	-	0	-
Cl 4, Table 1A(Air content (%), Max, over control)	-	0	-
Cl 4, Table 1 B(Minimum compressive strength ( 7 Days,28 Days, 6 Month and 1 Year))	-	0	-
Clause 4, Table 1B, SI no. (iii) (1 year minimum compressive strength, percent of control mix concrete)	-	0	-
Clause 4, Table 1B, SI no. (iii) (6 months minimum compressive strength, percent of control mix concrete)	-	0	-
Clause 4, Table 1B, SI no. (iii) (7 days minimum compressive strength, percent of control mix concrete)	-	0	-
Clause 4, Table 1A, SI no. (v) (28 days flexural strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (v) (7 days flexural strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (v) (3 days flexural strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (1 year compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (6 months compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (28 days compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (7 days compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (3 days compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iv) (1 day compressive strength, percent of control sample)	-	0	-
Clause 4, Table 1A, SI no. (iii) (Final time of setting allowable deviation from control sample)	-	0	-
Clause 4, Table 1A, SI no. (iii) (Initial time of setting allowable deviation from control sample)	-	0	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 1 Year )	-	0	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 6 Months days)	-	0	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 28 days)	-	0	-
4, Table 1B( minimum Compressive strength percent of control mix concrete 7 days)	-	0	-
4, Table 1A(Compressive strength percent of control Sample 1 year )	-	0	-
4, Table 1A(Compressive strength percent of control Sample 6 Months )	-	0	-
4, Table 1A(Compressive strength percent of control Sample 28 Days )	-	0	-
4, Table 1A(Compressive strength percent of control Sample 7 Days)	-	0	-
4, Table 1A(Compressive strength percent of control Sample 3 Days)	-	0	-
4, Table 1A(Compressive strength percent of control Sample 1 Day )	-	0	-
4, Table 1A(Length Change percent Increase over control Sample 1 year)	-	0	-
4, Table 1A(Length Change percent Increase over control Sample 6 Month)	-	0	-
4, Table 1A(Length Change percent Increase over control Sample 28 Day)	-	0	-
4, Table 1A(Flexural strength percent of control Sample 28 Day)	-	0	-
4, Table 1A(Flexural strength percent of control Sample 7 Day)	-	0	-
4, Table 1A(Flexural strength percent of control Sample 3 Day)	-	0	-
Cl 9 Table 2(Dry material content ( a-For liquid admixture, b- For solid admixture), Ash content, Relative density, Chloride ion content, pH)	-	0	-
Cl 9 Table 2(Dry material content ( a-For liquid admixture, b- For solid admixture), Ash content, Relative density, Chloride ion content, pH)	-	0	-
Cl 4, Table 1 B(Flow)	-	0	-
Cl 4, Table 1 B(Loss of workability on standing)	-	0	-
Clause 4, Table 1B, SI no. (iii) (28 days minimum compressive strength, percent of control mix concrete)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f 06.12.2024

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

M-30,M-35,M-40,M-50,M-55

21300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	500	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	100	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	500	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	100	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	100	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	500	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	100	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	100	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	100	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	300	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	100	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	100	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	100	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	600	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	1800	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)( Indivdual Compressive strength)	-	1800	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	100	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength )	-	1500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	100	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength )	-	1500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	100	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	3500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	500	-
Clause 7.3, Annex G(Individual Breaking Load)	-	500	-
Clause 7.3, Annex G(Average Breaking Load)	-	100	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	3500	-

Complete

26 Sep, 2025

-
Excluding freeze thaw durability

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

33,43,43-S, 53 and 53-S

14480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 Table-2 vi(Loss on ignition)	-	400	20% Discount to BIS
6.1 Table-2 iii.(Insoluble residue)	-	800	20% Discount to BIS
6.1 Table-2 viii(Alkali content)	-	1200	20% Discount to BIS
6.1 Table-2 vii(Chloride content)	-	1200	20% Discount to BIS
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	800	20% Discount to BIS
6.1 Table-2 iv(Magnesia)	-	800	20% Discount to BIS
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	2400	20% Discount to BIS
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	800	20% Discount to BIS
7 Table-3 i.(Fineness)	-	800	20% Discount to BIS
7 Table-3 ii a(Expansion by Le Chatelier)	-	640	20% Discount to BIS
7 Table-3 ii b(Expansion by Autoclave)	-	960	20% Discount to BIS
7 Table-3 iii a(Setting Time Initial)	-	640	20% Discount to BIS
7 Table-3 iii b(Setting Time Final)	-	640	20% Discount to BIS
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	800	20% Discount to BIS
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	800	20% Discount to BIS
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	800	20% Discount to BIS

Complete

26 Sep, 2025

-
-

IS 2185 : Part 1 (2005)

Concrete masonry units - Specification: Part 1 hollow and solid concrete blocks (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2 & 4.2(PHYSICAL REQUIREMENTS-Nominal Dimensions 1.Length 2.Hight 3. Width)	-	1000	-
9.2 & 4.2.3(Nominal Dimensions-variation in the length of units )	-	0	-
9.2 & 4.2.3(Nominal Dimensions -variation in height and width of units )	-	1000	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the face shell)	-	0	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the Web shell)	-	1000	-
9.3 & 5.1 & 5.2 Table 2(PHYSICAL REQUIREMENTS-Blocks Density - 1.Hollow (Open and Closed Cavity) Concrete Block- Grade Aor Grade B 2.Solid Concrete Block — Grade C)	-	1000	-
9.4- Table 2(PHYSICAL REQUIREMENTS - Compressive Strength 1.Minimum Average Compressive Strength of Units 2.Minimum Average Compressive Strength of Individual Unit)	-	5000	-
9.5(PHYSICAL REQUIREMENTS -Water Absorption)	-	1500	-
9.6(PHYSICAL REQUIREMENTS -Drying Shrinkage)	-	2500	-
9.7(PHYSICAL REQUIREMENTS -Moisture Movement)	-	2000	-
15(Marking)	-	0	-
9.2 & 4.2(PHYSICAL REQUIREMENTS-Nominal Dimensions 1.Length 2.Hight 3. Width)	-	0	-
9.2 & 4.2.3(Nominal Dimensions-variation in the length of units )	-	0	-
9.2 & 4.2.3(Nominal Dimensions -variation in height and width of units )	-	0	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the face shell)	-	0	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the Web shell)	-	0	-
9.3 & 5.1 & 5.2 Table 2(PHYSICAL REQUIREMENTS-Blocks Density - 1.Hollow (Open and Closed Cavity) Concrete Block- Grade Aor Grade B 2.Solid Concrete Block — Grade C)	-	0	-
9.4- Table 2(PHYSICAL REQUIREMENTS - Compressive Strength 1.Minimum Average Compressive Strength of Units 2.Minimum Average Compressive Strength of Individual Unit)	-	0	-
9.5(PHYSICAL REQUIREMENTS -Water Absorption)	-	0	-
9.6(PHYSICAL REQUIREMENTS -Drying Shrinkage)	-	0	-
9.7(PHYSICAL REQUIREMENTS -Moisture Movement)	-	0	-
15(Marking)	-	0	-
9.2 & 4.2(PHYSICAL REQUIREMENTS-Nominal Dimensions 1.Length 2.Hight 3. Width)	-	0	-
9.2 & 4.2.3(Nominal Dimensions-variation in the length of units )	-	0	-
9.2 & 4.2.3(Nominal Dimensions -variation in height and width of units )	-	0	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the face shell)	-	0	-
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the Web shell)	-	0	-
9.3 & 5.1 & 5.2 Table 2(PHYSICAL REQUIREMENTS-Blocks Density - 1.Hollow (Open and Closed Cavity) Concrete Block- Grade Aor Grade B 2.Solid Concrete Block — Grade C)	-	0	-
9.4- Table 2(PHYSICAL REQUIREMENTS - Compressive Strength 1.Minimum Average Compressive Strength of Units 2.Minimum Average Compressive Strength of Individual Unit)	-	0	-
9.5(PHYSICAL REQUIREMENTS -Water Absorption)	-	0	-
9.6(PHYSICAL REQUIREMENTS -Drying Shrinkage)	-	0	-
9.7(PHYSICAL REQUIREMENTS -Moisture Movement)	-	0	-
15(Marking)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 15622 (2017)

Pressed Ceramic Tiles - Specification (First Revision)

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5& 5.1, Table 1(Thickness- IS 13630(pt-1))	-	500	-
5& 5.1, Table 2(Thickness- IS 13630(pt-1))	-	0	-
5& 5.1, Table 3(Thickness- IS 13630(pt-1))	-	0	-
5& 5.1, Table 4(Thickness- IS 13630(pt-1))	-	0	-
6 table 5, i a (Length-IS 13630(pt-1))	-	0	-
6 table 5,i a (width-IS 13630(pt-1))	-	0	-
6 table 5, i b (Thickness- IS 13630(pt-1))	-	500	-
6 table 5, i c(Straigthness of side-IS 13630(pt-1))	-	500	-
6 table 5, i d(Rectangularity-IS 13630(pt-1))	-	500	-
6 table 5, i e(Surface flatness-IS 13630(pt-1))	-	500	-
6 table 5, i f(Surface quality-IS 13630(pt-1))	-	500	-
6 table 5, ii a(Water Absorption-IS 13630(pt-2))	-	1000	-
6 table 5, ii b(Module of rupture -IS 13630(pt-6))	-	2000	-
6 table 5, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 5, ii d(Moisture Expension-IS 13630(pt-3))	-	2500	-
6 table 5, ii e(Scratch hardness of surface -IS 13630(pt-13))	-	500	-
6 table 5, ii g(Thermal shock resistance IS 13630(pt-5))	-	1500	-
6 table 5, ii h(Impact resistance-IS 13630(pt-14))	-	1500	-
6 table 5, ii k(Crazing resistance-IS 13630(pt-9))	-	2000	-
6 table 5, iii a(Resistance to staining of glazed Tilles-IS 13630(pt-8))	-	1000	-
6 table 5, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound-IS 13630(pt-8))	-	1000	-
6 table 5, iii c(Resistance to acid and alkalis (with the exception ofhydrofluoric acid and its compounds – Glazed tiles-IS 13630(pt-8))	-	1000	-
6 table 6, i a (Length-IS 13630(pt-1))	-	500	-
6 table 6, i a (width-IS 13630(pt-1))	-	500	-
6 table 7, i b (Thickness-IS 13630(pt-1))	-	500	-
6 table 8, i c(Straigthness of side-IS 13630(pt-1))	-	500	-
6 table 6, i d(Rectangularity-IS 13630(pt-1))	-	500	-
6 table 6, i e(Surface flatness-IS 13630(pt-1))	-	500	-
6 table 6, ii a(Water Absorption-IS 13630(pt-2) )	-	1000	-
6 table 6, ii b(Module of rupture -IS 13630(pt-6))	-	2000	-
6 table 6, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 6, ii d(Moisture Expension-IS 13630(pt-3))	-	2500	-
6 table 6, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	-
6 table 6, ii h(Thermal shock resistance-IS13630(pt-5) )	-	500	-
6 table 6, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	-
6 table 6, ii k(Impact resistance-IS 13630(pt-14))	-	1500	-
6 table 6, ii n(Forst resistance-IS 13630(pt-10))	-	1500	-
6 table 6, iii a(Resistance to staining of glazed Tilles)	-	1000	-
6 table 6, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1000	-
6 table 6, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1000	-
6 table 7, i a (Length-IS 13630(pt-1))	-	500	-
6 table 7, i a (width-IS 13630(pt-1))	-	500	-
6 table 7, i c(Straigthness of side-IS 13630(pt-1))	-	500	-
6 table 7, i d(Rectangularity-IS 13630(pt-1))	-	500	-
6 table 7, i e(Surface flatness-IS 13630(pt-1))	-	500	-
6 table 7, i f(Surface quality-IS 13630(pt-1))	-	500	-
6 table 7, ii a(Water Absorption-IS 13630(pt-2) )	-	1000	-
6 table 7, ii b(Module of rupture-IS 13630(pt-6) )	-	2000	-
6 table 7, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 7, ii d(Moisture Expension-IS 13630(pt-3))	-	2500	-
6 table 7, ii e(Scratch hardness of surface-IS 13630(pt-13))	-	500	-
6 table 7, ii h(Thermal shock resistance-IS13630(pt-5) )	-	1500	-
6 table 7, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	-
6 table 7, ii k(Impact resistance-IS 13630(pt-14))	-	1500	-
6 table 7, ii n(Forst resistance-IS 13630(pt-10))	-	1000	-
6 table 7, iii a(Resistance to staining of glazed Tilles)	-	1000	-
6 table 7, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1000	-
6 table 7, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1000	-
6 table 8, i a (Length-IS 13630(pt-1))	-	500	-
6 table 8, i a (width-IS 13630(pt-1))	-	500	-
6 table 8, i b (Thickness-IS 13630(pt-1))	-	500	-
6 table 8, i d(Rectangularity-IS 13630(pt-1))	-	500	-
6 table 8, i e(Surface flatness-IS 13630(pt-1))	-	500	-
6 table 8, i f(Surface quality-IS 13630(pt-1))	-	500	-
6 table 8, ii a(Water Absorption-IS 13630(pt-6) )	-	1000	-
6 table 8, ii b(Module of rupture-IS 13630(pt-6) )	-	2000	-
6 table 8, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 8, ii d(Moisture Expension-IS 13630(pt-3))	-	2500	-
6 table 8, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	-
6 table 8, ii h(Thermal shock resistance-IS 13630(pt-5) )	-	1500	-
6 table 8, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	-
6 table 8, ii k(Impact resistance-IS 13630(pt-14))	-	1500	-
6 table 8, ii n(Forst resistance-IS 13630(pt-10))	-	1000	-
6 table 8, ii q(Bulk Density-IS13630(pt-2))	-	1000	-
6 table 8, iii a(Resistance to staining of glazed Tilles)	-	1000	-
6 table 8 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1000	-
6 table 8, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1000	-
6 table 9, i a (Length-IS 13630(pt-1))	-	500	-
6 table 9, i a (width-IS 13630(pt-1))	-	500	-
6 table 9, i b (Thickness-IS 13630(pt-1))	-	500	-
6 table 9, i c(Straigthness of side-IS 13630(pt-1))	-	500	-
6 table 9, i d(Rectangularity-IS 13630(pt-1))	-	500	-
6 table 9, i e(Surface flatness-IS 13630(pt-1))	-	500	-
6 table 9, i f(Surface quality-IS 13630(pt-1))	-	500	-
6 table 9, ii a(Water Absorption-IS 13630(pt-6) )	-	1000	-
6 table 9, ii b(Module of rupture-IS 13630(pt-6) )	-	2000	-
6 table 9, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 9, ii d(Moisture Expension-IS 13630(pt-3))	-	2500	-
6 table 9, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	-
6 table 9, ii h(Thermal shock resistance-IS 13630(pt-5))	-	1500	-
6 table 9, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	-
6 table 9, ii k(Impact resistance-IS 13630(pt-14))	-	1500	-
6 table 9, ii q(Bulk Density-)	-	1000	-
6 table 9, iii a(Resistance to staining )	-	1000	-
6 table 9 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1000	-
6 table 9, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1000	-
5& 5.1, Table 1(Thickness- IS 13630(pt-1))	-	0	-
5& 5.1, Table 2(Thickness- IS 13630(pt-1))	-	0	-
5& 5.1, Table 3(Thickness- IS 13630(pt-1))	-	0	-
5& 5.1, Table 4(Thickness- IS 13630(pt-1))	-	0	-
6 table 5, i a (Length-IS 13630(pt-1))	-	0	-
6 table 5,i a (width-IS 13630(pt-1))	-	0	-
6 table 5, i b (Thickness- IS 13630(pt-1))	-	0	-
6 table 5, i c(Straigthness of side-IS 13630(pt-1))	-	0	-
6 table 5, i d(Rectangularity-IS 13630(pt-1))	-	0	-
6 table 5, i e(Surface flatness-IS 13630(pt-1))	-	0	-
6 table 5, i f(Surface quality-IS 13630(pt-1))	-	0	-
6 table 5, ii a(Water Absorption-IS 13630(pt-2))	-	0	-
6 table 5, ii b(Module of rupture -IS 13630(pt-6))	-	0	-
6 table 5, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 5, ii d(Moisture Expension-IS 13630(pt-3))	-	0	-
6 table 5, ii e(Scratch hardness of surface -IS 13630(pt-13))	-	0	-
6 table 5, ii g(Thermal shock resistance IS 13630(pt-5))	-	0	-
6 table 5, ii h(Impact resistance-IS 13630(pt-14))	-	0	-
6 table 5, ii k(Crazing resistance-IS 13630(pt-9))	-	0	-
6 table 5, iii a(Resistance to staining of glazed Tilles-IS 13630(pt-8))	-	0	-
6 table 5, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound-IS 13630(pt-8))	-	0	-
6 table 5, iii c(Resistance to acid and alkalis (with the exception ofhydrofluoric acid and its compounds – Glazed tiles-IS 13630(pt-8))	-	0	-
6 table 6, i a (Length-IS 13630(pt-1))	-	0	-
6 table 6, i a (width-IS 13630(pt-1))	-	0	-
6 table 7, i b (Thickness-IS 13630(pt-1))	-	0	-
6 table 8, i c(Straigthness of side-IS 13630(pt-1))	-	0	-
6 table 6, i d(Rectangularity-IS 13630(pt-1))	-	0	-
6 table 6, i e(Surface flatness-IS 13630(pt-1))	-	0	-
6 table 6, ii a(Water Absorption-IS 13630(pt-2) )	-	0	-
6 table 6, ii b(Module of rupture -IS 13630(pt-6))	-	0	-
6 table 6, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 6, ii d(Moisture Expension-IS 13630(pt-3))	-	0	-
6 table 6, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	0	-
6 table 6, ii h(Thermal shock resistance-IS13630(pt-5) )	-	0	-
6 table 6, ii j(Crazing resistance-IS 13630(pt-9))	-	0	-
6 table 6, ii k(Impact resistance-IS 13630(pt-14))	-	0	-
6 table 6, ii n(Forst resistance-IS 13630(pt-10))	-	0	-
6 table 6, iii a(Resistance to staining of glazed Tilles)	-	0	-
6 table 6, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	0	-
6 table 6, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	0	-
6 table 7, i a (Length-IS 13630(pt-1))	-	0	-
6 table 7, i a (width-IS 13630(pt-1))	-	0	-
6 table 7, i c(Straigthness of side-IS 13630(pt-1))	-	0	-
6 table 7, i d(Rectangularity-IS 13630(pt-1))	-	0	-
6 table 7, i e(Surface flatness-IS 13630(pt-1))	-	0	-
6 table 7, i f(Surface quality-IS 13630(pt-1))	-	0	-
6 table 7, ii a(Water Absorption-IS 13630(pt-2) )	-	0	-
6 table 7, ii b(Module of rupture-IS 13630(pt-6) )	-	0	-
6 table 7, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 7, ii d(Moisture Expension-IS 13630(pt-3))	-	0	-
6 table 7, ii e(Scratch hardness of surface-IS 13630(pt-13))	-	0	-
6 table 7, ii h(Thermal shock resistance-IS13630(pt-5) )	-	0	-
6 table 7, ii j(Crazing resistance-IS 13630(pt-9))	-	0	-
6 table 7, ii k(Impact resistance-IS 13630(pt-14))	-	0	-
6 table 7, ii n(Forst resistance-IS 13630(pt-10))	-	0	-
6 table 7, iii a(Resistance to staining of glazed Tilles)	-	0	-
6 table 7, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	0	-
6 table 7, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	0	-
6 table 8, i a (Length-IS 13630(pt-1))	-	0	-
6 table 8, i a (width-IS 13630(pt-1))	-	0	-
6 table 8, i b (Thickness-IS 13630(pt-1))	-	0	-
6 table 8, i d(Rectangularity-IS 13630(pt-1))	-	0	-
6 table 8, i e(Surface flatness-IS 13630(pt-1))	-	0	-
6 table 8, i f(Surface quality-IS 13630(pt-1))	-	0	-
6 table 8, ii a(Water Absorption-IS 13630(pt-6) )	-	0	-
6 table 8, ii b(Module of rupture-IS 13630(pt-6) )	-	0	-
6 table 8, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 8, ii d(Moisture Expension-IS 13630(pt-3))	-	0	-
6 table 8, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	0	-
6 table 8, ii h(Thermal shock resistance-IS 13630(pt-5) )	-	0	-
6 table 8, ii j(Crazing resistance-IS 13630(pt-9))	-	0	-
6 table 8, ii k(Impact resistance-IS 13630(pt-14))	-	0	-
6 table 8, ii n(Forst resistance-IS 13630(pt-10))	-	1500	-
6 table 8, ii q(Bulk Density-IS13630(pt-2))	-	0	-
6 table 8, iii a(Resistance to staining of glazed Tilles)	-	0	-
6 table 8 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	0	-
6 table 8, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	0	-
6 table 9, i a (Length-IS 13630(pt-1))	-	0	-
6 table 9, i a (width-IS 13630(pt-1))	-	0	-
6 table 9, i b (Thickness-IS 13630(pt-1))	-	0	-
6 table 9, i c(Straigthness of side-IS 13630(pt-1))	-	0	-
6 table 9, i d(Rectangularity-IS 13630(pt-1))	-	0	-
6 table 9, i e(Surface flatness-IS 13630(pt-1))	-	0	-
6 table 9, i f(Surface quality-IS 13630(pt-1))	-	0	-
6 table 9, ii a(Water Absorption-IS 13630(pt-6) )	-	0	-
6 table 9, ii b(Module of rupture-IS 13630(pt-6) )	-	0	-
6 table 9, ii c(Bending Strength-IS 13630(pt-6))	-	0	-
6 table 9, ii d(Moisture Expension-IS 13630(pt-3))	-	0	-
6 table 9, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	0	-
6 table 9, ii h(Thermal shock resistance-IS 13630(pt-5))	-	0	-
6 table 9, ii j(Crazing resistance-IS 13630(pt-9))	-	0	-
6 table 9, ii k(Impact resistance-IS 13630(pt-14))	-	0	-
6 table 9, ii q(Bulk Density-)	-	0	-
6 table 9, iii a(Resistance to staining )	-	0	-
6 table 9 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	0	-
6 table 9, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	0	-
5& 5.1, Table 1(Coordinating size- IS 13630(pt-1))	-	500	-
5& 5.1, Table 1(Work size- IS 13630(pt-1))	-	500	-
5& 5.1, Table 2(Nominal size -IS 13630(pt-1))	-	0	-
5& 5.1, Table 2(Work size-IS 13630(pt-1))	-	0	-
5& 5.1, Table 3(Coordinating size- IS 13630(pt-1))	-	0	-
5& 5.1, Table 3(Work size-IS 13630(pt-1))	-	0	-
5& 5.1, Table 4(Nominal size-IS 13630(pt-1))	-	0	-
5& 5.1, Table 4(Work size-IS 13630(pt-1))	-	0	-
6 table 5, ii f(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS 13630(pt-4) )	-	1500	-
6 table 5, ii m(resistance to surface abrasion of glazed Tilles)	-	2000	-
5 table 6, ii f(Resistance to surface abrasion of glazed Tilles)	-	2000	-
6 table 6, ii p(Resistance to deep abrasion of unglazed tiles)	-	1500	-
6 table 7, ii f(Resistance to surface abrasion of glazed Tilles)	-	1500	-
6 table 7, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS13630(pt-4) )	-	1500	-
6 table 8, ii f(Resistance to surface abrasion of glazed Tilles)	-	1500	-
6 table 8, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS 13630(pt-4) )	-	1500	-
6 table 8, ii p(Resistance to deep abrasion of unglazed tiles)	-	1500	-
6 table 9, ii f(Resistance to surface abrasion of glazed Tilles)	-	1500	-
6 table 9, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C )	-	1500	-
6 table 9, ii n(Forst resistance-IS 13630(pt-10))	-	1500	-
6 table 9, ii p(Resistance to deep abrasion of unglazed tiles)	-	1500	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024 Only for dimension above 600mmx600mm and below 40mmx40mm

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

40000 View breakup
Rs. 40000/- (10% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	-
8(Protection against accidental contact with live parts)	-	2000	-
9(Terminals)	-	2500	-
11(MOISTURE RESISTANCE AND INSULATION)	-	3000	-
12(Electric Strength)	-	3000	-
14(Fault conditions)	-	3000	-
15(Transformer heating)	-	3000	-
16(Construction)	-	4000	-
17(Creepage distance and clearances)	-	4000	-
18(Screws, current carrying parts and connections)	-	2500	-
19(Resistance to heat, fire and tracking)	-	5000	-
20(Resistance to corrosion)	-	5000	-

Complete

26 Sep, 2025

-
Included w.e.f. 19.12.2023 Up to 300V AC, 50 Hz. Exclusion: Components: Enclosure, Bridging resistor in primary circuit, capacitor and RC units, RF suppression (X-Y capacitors), Inductor, MOV/VDR, SMPS/Mains Transformer, PCB for LED, Transparaent cover, Bobbin, Insulated tape, heat shrinkage sleeve, Connector, Fuse, Ointernal Wire, LED, Optocoupler, EMI/EMC filter, winding wire, thin sheet materials (Cl.16,19)

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	500	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	700	-
Cl 12.5(Water absorption)	-	1500	-
Cl 12.6(Wet transverse strength )	-	2000	-
Cl 12.7(Resistance to wear)	-	2000	-
Cl 11(Suface Finish)	-	500	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.2(Concavity & Convexity )	-	500	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 3812 : Part 2 (2013)

Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1, Table 1(Fineness — Specific surface in m2 /kg)	-	1000	-
7.1, Table 1(Particles retained on 45 micron IS sieve (wet sieving))	-	500	-
7.1, Table 1(Soundnes)	-	1200	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ) plus aluminium oxide (Al2O3 ) plus iron oxide (Fe2O3 ))	-	500	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ))	-	500	-
5.1, 6.1, Table 1(Magnesium oxide (MgO)	-	800	-
5.1, 6.1, Table 1(Total sulphur as sulphur trioxide (SO3)	-	500	-
5.1, 6.1, Table 1(Available alkalies as equivalent sodium oxide (Na2O))	-	1500	-
5.1, 6.1, Table 1(Total chlorides)	-	500	-
5.1, 6.1, Table 1(Loss on ignition)	-	500	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	500	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	500	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	500	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	800	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	500	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	1500	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	500	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	500	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1000	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	800	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	1500	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	0	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	500	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	1000	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	2000	-
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	0	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	0	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	0	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	0	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	0	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	0	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	0	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	0	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	0	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	0	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	0	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	0	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	0	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	0	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	0	-
7.2(Uniformity Requirements)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 455 (2015)

Portland slag cement - Specification

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	800	-
7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	800	-
7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	800	-
7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	600	-
7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	600	-
7 Table 1 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 Table 1 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	600	-
7 Table 1 i(Fineness IS 4031(Part 2))	-	800	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1200	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	500	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	800	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	800	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	800	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	500	-
7 Table 1 v(Transverse strength (optional) IS 4031(Part 8) )	-	1500	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1000	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1000	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	800	-
5.4.2(a)( Aggregates Impact Value)	-	700	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.2(a)( Aggregates Impact Value)	-	0	-
5.4.3(a)( Aggregate Abrasion Value)	-	700	-
5.4.3(b)( Aggregate Abrasion Value)	-	0	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	1000	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	0	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	0	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	0	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	0	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	0	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	0	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	1000	-
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	1000	-
6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	0	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	1000	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 4.75 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 2.36 mm Sieve)	-	0	-
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	1000	-
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	0	-
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	0	-
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	0	-
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	0	-
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	0	-
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	0	-
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	0	-
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	0	-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	1000	-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	0	-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	0	-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	0	-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	0	-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	0	-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	0	-
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	1000	-
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	0	-
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	0	-
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	0	-
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	0	-
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	500	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	500	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	700	-
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	700	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	1200	-
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	1000	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	500	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	500	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	1200	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	500	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	500	-
5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate))	-	700	-
5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate))	-	500	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	1000	-
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	1200	-
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	700	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	700	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	500	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	700	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	1200	-
7.2(Bulk Density loose)	-	500	-
7.2(Bulk Density Rodded)	-	500	-
7.2(Bulk Density loose)	-	500	-
7.2(Bulk Density Rodded)	-	500	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.2(a)( Aggregates Impact Value)	-	0	-
5.4.3(a)( Aggregate Abrasion Value)	-	0	-
5.4.3(b)( Aggregate Abrasion Value)	-	0	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	0	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	0	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	0	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	0	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	0	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	0	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	0	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	0	-
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	0	-
6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	0	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	0	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 4.75 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 2.36 mm Sieve)	-	0	-
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	0	-
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	0	-
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	0	-
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	0	-
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	0	-
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	0	-
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	0	-
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	0	-
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	0	-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	0	-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	0	-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	0	-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	0	-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	0	-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	0	-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	0	-
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	0	-
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	0	-
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	0	-
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	0	-
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	0	-
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	0	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	0	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	1000	-
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	1000	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	1500	-
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	0	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	0	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	0	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	0	-
5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate))	-	0	-
5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate))	-	0	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	0	-
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	0	-
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	0	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	0	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	0	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	0	-
5.5(Soundness By Magnesium Sulphate)	-	0	-
7.2(Bulk Density loose)	-	0	-
7.2(Bulk Density Rodded)	-	0	-
7.2(Bulk Density loose)	-	0	-
7.2(Bulk Density Rodded)	-	0	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1000	-
5.7 table 4 (Calcium oxide)	-	1000	-
3.2.2 Table 3 ii) IS 1963(Basicity as CaO/SiO2)	-	500	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	-
5.4.2(a)( Aggregates Impact Value)	-	0	-
5.4.3(a)( Aggregate Abrasion Value)	-	0	-
5.4.3(b)( Aggregate Abrasion Value)	-	0	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	0	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	0	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	0	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	0	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	0	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	0	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	0	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	0	-
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	0	-
6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	0	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	0	-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 4.75 mm Sieve)	-	0	-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 2.36 mm Sieve)	-	0	-
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	0	-
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	0	-
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	0	-
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	0	-
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	0	-
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	0	-
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	0	-
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	0	-
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	0	-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	0	-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	0	-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	0	-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	0	-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	0	-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	0	-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	0	-
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	0	-
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	0	-
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	0	-
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	0	-
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	0	-
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	0	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	0	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	0	-
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	0	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	0	-
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	0	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	0	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	0	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	0	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	0	-
5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate))	-	0	-
5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate))	-	0	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	0	-
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	0	-
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	0	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	0	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	0	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	0	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	0	-
5.5(Soundness By Magnesium Sulphate)	-	0	-
7.2(Bulk Density loose)	-	0	-
7.2(Bulk Density Rodded)	-	0	-
7.2(Bulk Density loose)	-	0	-
7.2(Bulk Density Rodded)	-	0	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	0	-
5.7 table 4 (Calcium oxide)	-	0	-
3.2.2 Table 3 ii) IS 1963(Basicity as CaO/SiO2)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f. 19.12.2023

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.4(Chloride content)	-	1000	-
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3500	-
Cl 3.2(Initial & Final)	-	1500	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	3000	-
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 7 days (168 ± 2 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar at 7 days (168 ± 2 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 3 days (72 ± 1 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar at 3 days (72 ± 1 h))	-	0	-
Clause 3.1 (Permeability to water of cement mortar with Water proofing compound)	-	0	-
Clause 3.4(Chloride content)	-	0	-
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	0	-
Cl 3.2(Initial & Final)	-	0	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	0	-
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 7 days (168 ± 2 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar at 7 days (168 ± 2 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 3 days (72 ± 1 h))	-	0	-
Clause 3.3(Compressive strength of cement mortar at 3 days (72 ± 1 h))	-	0	-
Clause 3.1 (Permeability to water of cement mortar with Water proofing compound)	-	0	-

Complete

26 Sep, 2025

-
Included w.e.f. 19.12.2023

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- i(Fineness 4031 Part 2)	-	800	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	600	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	600	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	800	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	800	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	800	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1200	-
7 -Table 2- i(Fineness 4031 Part 2)	-	0	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	0	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	0	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	0	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	0	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	0	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	0	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	0	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	0	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	0	-
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	0	-
7 -Table 2- i(Fineness 4031 Part 2)	-	0	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	0	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	0	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	0	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	0	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	0	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	0	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	0	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	0	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	0	-
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2500	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Average Compressive Strength)	-	700	-
5.4-Table-1 (v)-IS: 3025(P-17)(Suspended matter)	-	300	-
5.4-Table-1 (iv)-IS: 3025(P-32)(Chloride)	-	500	-
5.4-Table-1 (iii)-IS: 3025(P-32)(Chloride)	-	500	-
5.4-Table-1 (ii)-IS: 3025(P-24)(Sulphate)	-	250	-
5.4-Table-1 (i)-IS: 3025(P-18)(In-Organic)	-	350	-
5.4-Table-1 (i)-IS: 3025(P-18)(Organic )	-	350	-
5.4.2-IS: 3025(P-11)(Ph)	-	250	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	250	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	250	-
16.1(Compressive Strength of Individual Samples )	-	250	-
16.1(Compressive Strength of Individual Samples )	-	250	-
16.1(Compressive Strength of Individual Samples )	-	250	-

Complete

26 Sep, 2025

-
Included w.e.f. 19.12.2023

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	800	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	800	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	800	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	600	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	600	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	-
7 -Table 2- i(Fineness 4031 Part 2)	-	600	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1200	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	-
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	-
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	-
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 2185 : Part 3 (1984)

Concrete Masonry Units Part 3 Autoclaved Cellular Aerated Concrete Blocks

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Physical requirments-Dimensions-Length)	-	1000	-
8.2(Physical requirments-Dimensions-Height)	-	1000	-
8.2(Physical requirments-Dimensions-Width)	-	1000	-
8.3(Physical requirments- Block density)	-	4000	-
8.4(Physical requirments- Compressive strength)	-	5000	-
8.5(Thermal Conductivity)	-	3000	-
8.6( Drying Shrinkage )	-	2500	-
8.4, 9.2 & 11.3(Indivisual Moisture Content)	-	500	-
8.3 & 9.1 Table 1(Indivisual Block Density)	-	500	-
8.4, 9.2 & 11.3 & Table 1(Indivisual Compressive strength)	-	500	-
3.2 & 8.2(Indivisual Height)	-	500	-
3.2 & 8.2(Indivisual Width)	-	500	-
3.2 & 8.2(Indivisual Length)	-	500	-
8.2(Physical requirments-Dimensions-Length)	-	-	-
8.2(Physical requirments-Dimensions-Height)	-	-	-
8.2(Physical requirments-Dimensions-Width)	-	-	-
8.3(Physical requirments- Block density)	-	-	-
8.4(Physical requirments- Compressive strength)	-	-	-
8.5(Thermal Conductivity)	-	-	-
8.6( Drying Shrinkage )	-	-	-
8.4, 9.2 & 11.3(Indivisual Moisture Content)	-	-	-
8.3 & 9.1 Table 1(Indivisual Block Density)	-	-	-
8.4, 9.2 & 11.3 & Table 1(Indivisual Compressive strength)	-	-	-
3.2 & 8.2(Indivisual Height)	-	-	-
3.2 & 8.2(Indivisual Width)	-	-	-
3.2 & 8.2(Indivisual Length)	-	-	-

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

3150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	500.00	5% Discount for BIS
8.2(Construction, IS 9537-2)	-	500.00	5% Discount for BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500.00	5% Discount for BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	500.00	5% Discount for BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500.00	5% Discount for BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	1000.00	5% Discount for BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1000.00	5% Discount for BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1000.00	5% Discount for BIS
6.1(Marking, IS 9537-2)	-	2000	5% Discount for BIS
8.2(Construction, IS 9537-2)	-	500	5% Discount for BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	5% Discount for BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	500	5% Discount for BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500	5% Discount for BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	500	5% Discount for BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	500	5% Discount for BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	500	5% Discount for BIS
6.1(Marking, IS 9537-2)	-	200	5% Discount for BIS
8.2(Construction, IS 9537-2)	-	500	5% Discount for BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	5% Discount for BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	500	5% Discount for BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500	5% Discount for BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	500	5% Discount for BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	500	5% Discount for BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	500	5% Discount for BIS
7.4(Screw threads, IS 9537-2)	-	500	5% Discount for BIS
8.1(Construction, Cl. 8 of IS 9537-1)	-	500	5% Discount for BIS
13(External Influences, IS 9537-2)	-	500	5% Discount for BIS
6.1(Marking, IS 9537-2)	-	500	5% Discount for BIS
8.2(Construction, IS 9537-2)	-	500	5% Discount for BIS
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	200	5% Discount for BIS
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	200	5% Discount for BIS
7.3(Dimensions (Wall thickness), IS 9537-2)	-	500	5% Discount for BIS
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	200	5% Discount for BIS
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	500	5% Discount for BIS
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1000	5% Discount for BIS
7.4(Screw threads, IS 9537-2)	-	500	5% Discount for BIS
8.1(Construction, Cl. 8 of IS 9537-1)	-	200	5% Discount for BIS
13(External Influences, IS 9537-2)	-	500	5% Discount for BIS

Complete

26 Sep, 2025

-
Included w.e.f. 28.03.2024

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

4950.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.2(Maximum and minimum outside diameter of conduit)	-	500.00	5% Discount for BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	500.00	5% Discount for BIS
7.2(Minimum inside diameter of conduit)	-	500.00	5% Discount for BIS
7.4(Unifomity of The wall Thickness)	-	1000.00	5% Discount for BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000.00	5% Discount for BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
10(Resistance to Heat -Ball presure test)	-	1000.00	5% Discount for BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1500.00	5% Discount for BIS
6.1(Marking)	-	500.00	5% Discount for BIS
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500.00	5% Discount for BIS
7.1.2(Maximum and minimum outside diameter of conduit)	-	500	5% Discount for BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	500	5% Discount for BIS
7.2(Minimum inside diameter of conduit)	-	500	5% Discount for BIS
7.4(Unifomity of The wall Thickness)	-	500	5% Discount for BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000	5% Discount for BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1000	5% Discount for BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	5000	5% Discount for BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
10(Resistance to Heat -Ball presure test)	-	1000	5% Discount for BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	700	5% Discount for BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1000	5% Discount for BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1000	5% Discount for BIS
6.1(Marking)	-	200	5% Discount for BIS
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
7.3(Length of conduit)	-	500	5% Discount for BIS
7.1.2(Maximum and minimum outside diameter of conduit)	-	200	5% Discount for BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	200	5% Discount for BIS
7.2(Minimum inside diameter of conduit)	-	200	5% Discount for BIS
7.4(Unifomity of The wall Thickness)	-	500	5% Discount for BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	500	5% Discount for BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
10(Resistance to Heat -Ball presure test)	-	500	5% Discount for BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	500	5% Discount for BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1000	5% Discount for BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1000	5% Discount for BIS
6.1(Marking)	-	200	5% Discount for BIS
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	200	5% Discount for BIS
7.3(Length of conduit)	-	200	5% Discount for BIS
7.1.2(Maximum and minimum outside diameter of conduit)	-	-	-
7.1.1(Maximum and minimum outside diameter of socket)	-	-	-
7.2(Minimum inside diameter of conduit)	-	-	-
7.4(Unifomity of The wall Thickness)	-	-	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	-	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	-	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	-	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	-	-
10(Resistance to Heat -Ball presure test)	-	-	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	-	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	-	-
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	-	-
6.1(Marking)	-	-	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	-	-
7.3(Length of conduit)	-	-	-

Complete

26 Sep, 2025

-
Included w.e.f. 19.12.2023

Bureau of Indian Standards

The National Standards Body of India

Stellar Test House

G-68, Sector-63, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

8130190099 ankit@stellartesthouse.com

Scope List