BIS - LIMS (Laboratory Information Management System)

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

487/59, Ground Floor, Village Peeragarhi, National Market, New Delhi, West, Delhi, 110087

9810730485 lab@universaltesthouse.com

Scope List

Reset

21 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1328 (2025)

Veneered Decorative Plywood - Specification ( Fourth Revision )

MR (moisture resistant) grade, BWR (boiling water resistant) grade, BWP (boiling water proof) grade

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Grades)	-	0	-
Cl 4.2(Type)	-	0	-
Cl 4.3(Formaldehyde Class)	-	0	-
Cl 5.2(Adhesive)	-	0	-
Cl 7.1(Surface Requirements- For Type 1)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 7.2(Surface Requirements- For Type 2)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 7.3(Surface Requirements- For Type 3)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 7.4(Surface Requirements- For Type 4)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 8.1(Dimensions (Length and Width))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 8.2(Dimensions (Thickness))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 8.3(Squareness and Edge Straightness as Per Annex B)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 8.4- Table 1(Tolerances)	-	0	-
Cl 11.3(Moisture Content)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 11.4.1(a)(Water Resistance Test( For MR Grade))	-	800	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 11.4.1(b)(Water Resistance Test( For BWR Grade))	-	800	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 11.4.1(c)(Water Resistance Test( For BWP Grade))	-	800	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 11.5(Formaldehyde Content Test)	-	5500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl 11.6(Steady - State Formaldehyde Emission Test ( Optional Test))	-	60000	20% Discount for BIS Sample (Optional test, Mentioned charges for steady state Formaldehyde testing 60000/-, Testing time 30Days).
Cl 12(Marking)	-	0	-

28 Nov, 2027

-
Included w.e.f 27.01.2026

IS 14587 (2025)

Prelaminated Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials - Specification ( Second Revision )

Regular (REG) Grade, Moisture Resistance (MR) Grade, High Moisture Resistance General Purpose (HMR-GP) Grade, High Moisture Resistance Furniture (HMR-FN) Grade

15200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	200	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	200	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	100	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	250	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	250	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	2000	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	2000	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	1000	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	5500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	60000	20% Discount for BIS Sample (Optional test, Mentioned charges for steady state Formaldehyde testing 60000/-, Testing time 30Days)

28 Nov, 2027

-
Included w.e.f 27.01.2026

IS 12406 (2025)

Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

Regular (REG) grade, Moisture resistance (MR) grade, High moisture resistance (HMR) grade- General purpose (GP) grade, Furniture purpose (FN) grade

12200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	200	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	200	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	200	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	100	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	250	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 8, Table 2(Edge straightness, Max.)	-	250	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	5500	10 % Discount to BIS and for others 1.5 times of mentioned testing charges.
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	60000	20% Discount for BIS Sample (Optional test, Mentioned charges for steady state Formaldehyde testing 60000/-, Testing time 30Days)
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	0	-
Cl-5.2(Adhesive)	-	0	-
Cl-5.3(Sizing Material)	-	0	-
Cl-5.4(Preservative Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-

28 Nov, 2027

-
Included w.e.f 27.01.2026

IS 848 (2025)

Synthetic Resin Adhesives for Plywood (Phenolic, Aminoplastic and Bio-Materials Based) - Specification ( Third Revision )

BWP (Boiling Water Proof), BWR (Boiling Water Resistance), MR (Moisture Resistance)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 4 Table 1(TYPES)	-	0	-
As per Clause 6.6(SETTING TIMES AND CONDITIONS)	-	0	-
As per Clause 7.3.2 Table 1(i)(Cyclic Test For BWP Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.3.2 Table 1(ii)(Cyclic Test For BWR Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.3.2 Table 1(iii)(Cyclic Test For MR Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.4(Acidity And Alkalinity (pH))	-	1500	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 9(Marking)	-	0	-
As per Clause 4 Table 1(TYPES)	-	0	-
As per Clause 6.6(SETTING TIMES AND CONDITIONS)	-	0	-
As per Clause 7.3.2 Table 1(i)(Cyclic Test For BWP Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.3.2 Table 1(ii)(Cyclic Test For BWR Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.3.2 Table 1(iii)(Cyclic Test For MR Type)	-	7000	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 7.4(Acidity And Alkalinity (pH))	-	1500	10 % Discount to BIS and For Others 1.5 times of mentioned testing charged
As per Clause 9(Marking)	-	0	-

28 Nov, 2027

-
Included w.e.f 16.12.2025

IS 3087 (2025)

Medium Density Particle Boards of Wood and other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

Regular (REG) grade- A, Regular (REG) grade- B, Moisture resistance (MR) grade, High moisture resistance (HMR) grade

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	200	10 % Discount for BIS Samples
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	200	10 % Discount for BIS Samples
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	200	10 % Discount for BIS Samples
As per Clause 8, Table 2(Thickness, Sanded/finished panel - IS 2380 (Part 2))	-	100	10 % Discount for BIS Samples
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	250	10 % Discount for BIS Samples
As per Clause 8, Table 2(Edge straightness, Max. -IS 2380 (Part 2))	-	250	10 % Discount for BIS Samples
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	700	10 % Discount for BIS Samples
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	800	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	800	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	800	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	700	10 % Discount for BIS Samples
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	700	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	700	10 % Discount for BIS Samples
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	700	10 % Discount for BIS Samples
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	7800	10 % Discount for BIS Samples
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)

28 Nov, 2027

-
Included w.e.f 08.12.2025

IS 12823 (2025)

Prelaminated Medium Density Particle Boards from Wood and other Lignocellulosic Material Specification (Second Revision)

Regular (REG) Grade A, Regular (REG) Grade B, Moisture Resistance (MR) Grade, High Moisture Resistance (HMR) Grade

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Material - IS 3087)	-	200	10 % Discount for BIS Samples
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	200	10 % Discount for BIS Samples
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	200	10 % Discount for BIS Samples
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	100	10 % Discount for BIS Samples
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	250	10 % Discount for BIS Samples
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	250	10 % Discount for BIS Samples
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	750	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	750	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	500	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	250	10 % Discount for BIS Samples
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	250	10 % Discount for BIS Samples
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	10 % Discount for BIS Samples
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	4800	10 % Discount for BIS Samples
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)

28 Nov, 2027

-
Included w.e.f 06.01.2026

IS 4990 (2024)

PLYWOOD FOR CONCRETE SHUTTERING WORKS SPECIFICATION (Fourth Revision)

All Grade BWP, CS/CSC/CSFF

20300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Timber)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-5.2(Adhesives for Bonding of Veneers)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.1(Manufacture)	-	0	-
Cl-6.2(Manufacture ( Thickness of veneers))	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.3(Manufacture ( Physical and mechanical properties of veneers))	-	0	-
Cl-6.4, 6.7(Manufacture (Plywood for concrete shuttering))	-	0	-
Cl-6.5(Manufacture (Scarf joints))	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.6(Manufacture ( Preservative treatment))	-	0	-
Cl-7.1(Dimensions -length)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-7.2(Thickness)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-7.3(Squareness)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-8.1, 8.2(Workmanship and finish)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.3(Moisture Content)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.4.1(Glue Adhesion in Dry State - Glue Shear Strength)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.4.2(Glue Adhesion in Dry State - Adhesion of Plies)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.5, 10.5.1(Resistance to Water Test)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.5.1.1(Water Resistance Test-Glue shear strength)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.5.1.2(Water Resistance Test-Adhesion of plies)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.5.2(Water Resistance Test (Alternate method))	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.6(Water resistance test (Concrete shuttering Plywood))	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.7.1, Table-2(Mycological Test- Glue shear strengt)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.7.2(Mycological Test- Adhesion of plies)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.8(Tensile Strength)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.9, Table-3 (i)(Along (parallel to the grain direction of the face veneer))	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.9, Table-3 (ii)(Across (perpendicular to the grain direction of the face veneer))	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.10, Table-4 (i) a(Wet Bending Strength -Modulus of Elasticity (MOE),- Average)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.10, Table-4 (i) b(Wet Bending Strength - Modulus of Elasticity (MOE),- Minimum individual)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.11(Retention of Preservative)	-	3500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.12(Formaldehyde Content Test)	-	4500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-10.13(Steady-State Formaldehyde Emission Test)	-	45000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)

28 Nov, 2027

-
Included w.e.f. 24.03.2025

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

All Grade

20300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Timber)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-4.2(Adhesive)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-5.1(Veneers)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-5.2.1(Glueing)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl -5.2.2(Thickness of Veneers)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl - 5.2.3.1(Joint in Veneers)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl - 5.2.3.2(Edge joints)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl - 5.2.3.3(End joints)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl - 5.2.3.4(Scarf joints)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl - 5.2.4(Grain Direction)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-5.3(Treatment)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-5.4(Moisture Content)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.1(Dimensions (length))	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.2(Thickness)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-6.3(Squareness)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6(Workmanship and finish)	-	300	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.3(Moisture Content)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.4.2(Glue Adhesion in Dry State- Adhesion of Plies)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength -Average)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.5.1.1(Glue Adhesion in Water Resistance - Glue Shear Strength -Average)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.5.1.2(Water Resistance Test-Adhesion of plies)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.5.2(Water Resistance Test)	-	500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.6(Tensile Strength-Along the grain)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.7(Mycological Test -Adhesion)	-	1000	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.9, Table-3 (i) a(Wet Bending Strength- Modulus of Elasticity (MOE)- Average)	-	1500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.9, Table-3 (i) b(Wet Bending Strength- Modulus of Elasticity (MOE),-Minimum individual)	-	1500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.10(Retention of Preservative)	-	2500	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.11(Formaldehyde Content Test)	-	3700	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
Cl-9.12(Steady-State Formaldehyde Emission Test)	-	45000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
Cl-9.4.2(Adhesion of Plies)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.
5.1.1(Defects in veneers)	-	100	10% Discount to BIS & for others 1.5 times of mentioned testing charges.

28 Nov, 2027

-
Included w.e.f. 24.03.2025

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

All

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(BWP (BOiling WaterProof))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
4 Table (i)(BWR (Boiling Water Resistant))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
4 Table (i)(MR (Moisture Ressistant))	-	7000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
5,7.4(Keeping Quality (Resistance to heat Polymerization))	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
7.4(Acidity and Alkalinity ( pH))	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.

28 Nov, 2027

-
Included w.e.f. 24.03.2025

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

Grade- MR/BWR/BWP, Type- A & B

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (i)(Blister)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (ii)(Checks)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (iii)(Discolouration)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (iv)(Dote)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (v)(Insect hole)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (vi)(Joints)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (x)(Knots (tight))	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xi)(Patches)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xii)(Splits)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table- 1 (xiii)(Swirl)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-6.1(Timber)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-6.2(Adhesive)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.1(Thickness of veneers)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.3(Grain Direction)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.2(Splits)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.5.3(Overlap)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.1(Dimensions -length)	-	300	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.2(Thickness of the plywood boards)	-	300	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-8.3(Squareness)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.3.2(Mycological Test)	-	1500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.4(Moisture Content)	-	500	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1000	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.6(Formaldehyde Content Test)	-	4600	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
Cl-9(WORKMANSHIP AND FINISH)	-	100	10% Discount to BIS and for others 1.5 times of mentioned testing charges.
Cl-7.2.4(Scarf Joints)	-	0	10% Discount to BIS and for others 1.5 times of mentioned testing charges.

28 Nov, 2027

-
Included w.e.f. 24.03.2025

IS 14587 (2023)

Prelaminated Medium Density Fibre Board - Specification

Grade 1 & 2

15200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Medium Density Fibre (MDF) Board)	-	0	10% Discount for BIS Samples
Cl-7(Finish)	-	200	10% Discount for BIS Samples
Cl-8.1(Dimensions of prelaminated MDF)	-	500	10% Discount for BIS Samples
Cl-8.2(Tolerances)	-	250	10% Discount for BIS Samples
Cl-8.2.1(Edge straightness)	-	250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), i(Density, kg/m3)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), ii(Variation from mean density, percent)	-	0	ok
Cl-9.1 S.No-(1), iii(Moisture content, percent)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), iv(Variation from mean moisture content, percent (absolute))	-	0	ok
Cl-9.1 S.No-(1), v(Linear expansion (thickness swelling in water), due to general absorption after 24 h soaking, percent, Max)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vi(Internal bond strength, N/mm2, Min)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vii,a(After cyclic test)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), vii,b(After accelerated water resistance test)	-	0	ok
Cl-9.1 S.No-(1), viii(Modulus of rupture, N/mm2 , Min)	-	1250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), ix(Modulus of elasticity, N/mm2 , Min)	-	1250	10% Discount for BIS Samples
Cl-9.1 S.No-(1), x,(Screw withdrawal strength, ????????, Min)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xi(Formaldehyde content (Fc), mg/100 g for oven dry board)	-	5500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xii(Steady-state formaldehyde emission (Fc), mg/m3)	-	60000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
Cl-9.1 S.No-(1), xiii(Abrasion resistance in number of revolutions, Min, (Type 1 to 4))	-	1000	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xiv(Resistance to steam/water vapours)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xv(Resistance to crack)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xvi(Resistance to a cigarette burn)	-	500	10% Discount for BIS Samples
Cl-9.1 S.No-(1), xvii(Resistance to stain)	-	500	10% Discount for BIS Samples
Cl-11.2(Specific Requirement)	-	0	ok
Cl-12(Marking)	-	0	ok

28 Nov, 2027

-
-

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

Grade 1 & 2

12200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 5.2, 9 and 10.2.2(Density)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Density)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Variation from mean density)	-	200	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Moisture Content)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Variation from mean moisture content)	-	200	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Internal Bond Strength)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Internal Bond strength (i) (After Cyclic test) (ii) (After accelerated water resistance test))	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Modulus of Rupture a) Avg. Value b) Min. Individual)	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Modulus of Elasticity a) Avg. Value b) Min. Individual)	-	500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-	1000	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	5500	10% Discount for BIS Samples
Clauses 5.2, 9 and 10.2.2(Steady State Formaldehyde emission (Fc (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	45000	20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)
8(DIMENSIONS AND TOLERANCES)	-	500	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

Grade 1& 2

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Finish)	-	500	10% Discount for BIS Samples
Cl 8(Dimensions & Tolerances)	-	2000	10% Discount for BIS Samples
Cl 10.2(Test For Density)	-	1000	10% Discount for BIS Samples
Cl 10.3(Test For Moisture Content)	-	1000	10% Discount for BIS Samples
Cl 10.4(For Water AbsorptionTest )	-	1000	10% Discount for BIS Samples
Cl 10.5(For Swelling in water Test )	-	1000	10% Discount for BIS Samples
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	3000	10% Discount for BIS Samples
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1000	10% Discount for BIS Samples
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	1000	10% Discount for BIS Samples
Cl 10.9(Test For Screw Withdrawal Strength)	-	1000	10% Discount for BIS Samples
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	1000	10% Discount for BIS Samples
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	1000	10% Discount for BIS Samples
Cl 10.12 & Annex E( Test For Crack Resistance)	-	1000	10% Discount for BIS Samples
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	1000	10% Discount for BIS Samples
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	1000	10% Discount for BIS Samples
Cl 4(Grades & Types)	-	0	ok
Cl 10.15(Test for Formaldehyde Content/Emission)	-	4800	10% Discount for BIS Samples according test IS 13745 20% Discount for BIS Samples (Optional Test, Mentioned charges are for the Steady State Formaldehyde Testing 60000/- , Testing Time 30Days)

28 Nov, 2027

-
-

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Grade 1& 2

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1(Density Variation (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (i) Table 1(Density Variation (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) Table 1 (b)(Water absorption, 24h soacking (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Tubular) XPS)	-	1000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Tubular) XPS)	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Single Layer))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 1))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 2))	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Solids) XPS)	-	3000	10% Discount for BIS Samples
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Tubular) XPT)	-	3000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface,Upto 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Single Layer))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface,Above 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	10% Discount for BIS Samples
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	10% Discount for BIS Samples
7(Finish)	-	1000	10% Discount for BIS Samples
8.3(Dimensional Tolerances)	-	2000	10% Discount for BIS Samples
9.2, 11.4(Moisture content)	-	1000	10% Discount for BIS Samples
11.10(screw withdrawal strength)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

MR & BWP

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.6(Spot test - Annexure L)	-	1500	10% Discount for BIS Samples
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	1600	10% Discount for BIS Samples
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	1500	10% Discount for BIS Samples
9.2.3(Adhesion of Plies - Annexure H)	-	600	10% Discount for BIS Samples
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	1000	10% Discount for BIS Samples
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	1000	10% Discount for BIS Samples
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	1000	10% Discount for BIS Samples
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	1000	10% Discount for BIS Samples
7.3(Dimensional Requirements - Squareness - Annexure D)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Thickness - Annexure E)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Width - 8.1.4)	-	500	10% Discount for BIS Samples
7.3(Dimensional Requirements - Length - 8.1.4)	-	500	10% Discount for BIS Samples
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	500	10% Discount for BIS Samples
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	500	10% Discount for BIS Samples
9.2.6 (mechanical)(Spot test - Annexure L)	-	1500	10% Discount for BIS Samples
cl. 11(marking)	-	0	-
cl. 11.1(marking - BIS certification marking)	-	0	-

28 Nov, 2027

-
-

IS 10701 (2012)

Structural plywood - Specification (First Revision)

BWP & BWR

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.3(Glue Shear strength in dry state)	-	2000	10% Discount for BIS Samples
11.4.1(Resistance to Water)	-	2000	10% Discount for BIS Samples
11.4.2(Resistance to Water)	-	1000	10% Discount for BIS Samples
11.6(Tensile Strength)	-	1600	10% Discount for BIS Samples
11.7.1(Compressive Strength, Bending Strength, Panel Shear Strength, Plate Shear Strength and Rolling Shear Strngth)	-	6000	10% Discount for BIS Samples
11.8(Wet Bending Strength)	-	5000	10% Discount for BIS Samples
Clause 11.2(Moisture content)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 1328 (1996)

Veneered Decorative Plywood -Specification

MR & BWR

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	500	10% Discount for BIS Samples
4.1(Grade - For MR)	-	500	10% Discount for BIS Samples
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	500	10% Discount for BIS Samples
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	500	10% Discount for BIS Samples
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	500	10% Discount for BIS Samples
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	500	10% Discount for BIS Samples
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	500	10% Discount for BIS Samples
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	10% Discount for BIS Samples
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	10% Discount for BIS Samples
9(Finish - Cl. 9.1, 8.3)	-	500	10% Discount for BIS Samples
9(Finish - Cl. 9.2, 8.3)	-	500	10% Discount for BIS Samples
11(Tests - Moisture Content - Part 1 of IS 1734)	-	500	10% Discount for BIS Samples
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	800	10% Discount for BIS Samples
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	800	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

MR, BWR & BWP

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3 (Table 1)(b) 6 mm and above)	-	500	10% Discount for BIS Samples
4.1(Flame retardant chemicals)	-	0	-
4.2(Flame retardant and preservative treatment)	-	0	-
4.3(Treatment)	-	0	-
5(PREPARATION FOR TREATMENT)	-	0	-
6.1.1(Treatment of Plywood by Pressure Impregnation after Manufacture)	-	0	-
6.1.2(Soaking Treatment)	-	0	-
6.2(Choice of Treatment)	-	0	-
7(CONDITIONING AFTER TREATMENT)	-	0	-
8.1(Dimensions)	-	1000	10% Discount for BIS Samples
8.2(Thickness)	-	500	10% Discount for BIS Samples
8.3, Taable-1 (i)(Tolerance- Length)	-	500	10% Discount for BIS Samples
9(WORKMANSHIP AND FINISH)	-	200	10% Discount for BIS Samples
10(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
11 (a)(For flammability)	-	2000	10% Discount for BIS Samples
11 (b)(For flame penetration)	-	2000	10% Discount for BIS Samples
11 (c)(For rate of burning)	-	2200	10% Discount for BIS Samples
12.1 Table - 2 (i)(Moisture content, percent, Max)	-	500	10% Discount for BIS Samples
12.1 Table - 2 (ii)(Flammability (see Note 1), minutes, Min)	-	2000	10% Discount for BIS Samples
12.1 Table - 2 (iii)(Flame penetration (see Note 2), minutes, Min)	-	2000	10% Discount for BIS Samples
12.1 Table - 2 (iv)(Rate of burning (see Note 3), minutes, Min)	-	2200	10% Discount for BIS Samples
12.2(Other Tests)	-	2600	10% Discount for BIS Samples
14(Marking)	-	0	-

28 Nov, 2027

-
-

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

BWP & BWR

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	0	-
7.2(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.2(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.3(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.4(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
7.4(DIMENSIONS & TOLERANCES )	-	500	10% Discount for BIS Samples
8.1(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
8.3(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
10.1.1(MOISTURE CONTENT)	-	500	10% Discount for BIS Samples
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	600	10% Discount for BIS Samples
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	500	10% Discount for BIS Samples
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	500	10% Discount for BIS Samples
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	600	10% Discount for BIS Samples
10.1.5(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.5.2(MYCOLOGICAL TEST )	-	2600	10% Discount for BIS Samples
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	1200	10% Discount for BIS Samples
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	1200	10% Discount for BIS Samples
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1600	10% Discount for BIS Samples
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1600	10% Discount for BIS Samples
10.1.9(RETENTION OF PRESERVATIVE)	-	2000	10% Discount for BIS Samples
10.1.6(TENSILE STRENGTH)	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3)(Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2)(Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1000	10% Discount for BIS Samples
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-	1000	10% Discount for BIS Samples
Cl. 10.1.6(Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-	1000	10% Discount for BIS Samples
10.1.9(Chem)(RETENTION OF PRESERVATIVE)	-	2000	10% Discount for BIS Samples
12, 12.1(MARKING)	-	0	ok
12, 12.2(MARKING)	-	0	ok
cl. 10.1.2.1(glue adhesion in dry state - glue shear strength - AVERAGE)	-	1000	10% Discount for BIS Samples
cl. 10.1.2.1(glue adhesion in dry state - glue shear strength - WOOD FAILURE, Average)	-	1000	10% Discount for BIS Samples
cl. 10.1.3.1(resistance to water test - glue shear strength - AVERAGE)	-	2000	10% Discount for BIS Samples
cl. 10.1.3.1(resistance to water test - glue shear strength - WOOD FAILURE, Average)	-	2000	10% Discount for BIS Samples
cl. 10.1.5.1(mycological test - glue shear strength - AVERAGE)	-	2600	10% Discount for BIS Samples
cl. 10.1.5.1(mycological test - glue shear strength - WOOD FAILURE, Average)	-	2600	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 710 (2010)

Marine plywood - Specification (Second Revision)

BWP & BWR

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.2(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.3(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
7.5(WORKMANSHIP AND FINISH )	-	200	10% Discount for BIS Samples
6.1(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.1(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.2(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.3(DIMENSIONS)	-	500	10% Discount for BIS Samples
6.3(DIMENSIONS)	-	500	10% Discount for BIS Samples
9.1.1(MOISTURE CONTENT)	-	500	10% Discount for BIS Samples
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	600	10% Discount for BIS Samples
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	600	10% Discount for BIS Samples
9.1.3 , 9.1.3.1.1(Water resistance test)	-	500	10% Discount for BIS Samples
9.1.3 , 9.1.3.1.2(Water resistance test)	-	500	10% Discount for BIS Samples
9.1.5(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.5 , 9.1.3.1.1(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.5 , 9.1.3.1.2(Mycological test)	-	2600	10% Discount for BIS Samples
9.1.4(Tensile strength)	-	1000	10% Discount for BIS Samples
9.1.6 (Table 3)(Static bending strength)	-	1200	10% Discount for BIS Samples
9.1.6 (Table 3)(Static bending strength)	-	1200	10% Discount for BIS Samples
9.1.7 (Table 4)(Wet bending strength)	-	1600	10% Discount for BIS Samples
9.1.7 (Table 4)(Wet bending strength)	-	1600	10% Discount for BIS Samples
9.1.8(Retention of preservative)	-	2000	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	1200	10% Discount for BIS Samples
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	1200	10% Discount for BIS Samples
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	1000	10% Discount for BIS Samples
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	1000	10% Discount for BIS Samples
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	1000	10% Discount for BIS Samples
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	2600	10% Discount for BIS Samples
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	2600	10% Discount for BIS Samples
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	600	10% Discount for BIS Samples
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	600	10% Discount for BIS Samples
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	500	10% Discount for BIS Samples
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	500	10% Discount for BIS Samples
cl.5.1(manufacture - Veneers)	-	1000	10% Discount for BIS Samples
cl.5.1(manufacture - Veneers - moisture content)	-	2000	10% Discount for BIS Samples
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	1000	10% Discount for BIS Samples
cl.5.2.2(Assembly - Thickness of Veneers)	-	1000	10% Discount for BIS Samples

28 Nov, 2027

-
-

IS 303 (1989)

Plywood for General Purposes -

MR & BWR

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions & Tolerances - Length - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Width - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	300	10% Discount For BIS Sample
8(Dimensions & Tolerances - Squareness - Annexure C)	-	300	10% Discount For BIS Sample
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	200	10% Discount For BIS Sample
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	500	10% Discount For BIS Sample
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	500	10% Discount For BIS Sample
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	2000	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1600	10% Discount For BIS Sample
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1600	10% Discount For BIS Sample
11.3(Moisture Content - Part 1 of IS 1734)	-	500	10% Discount For BIS Sample
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	0	ok
5.1(Type - For BB Type)	-	0	ok
5.1(Type - For AB Type)	-	0	ok
5.1(Type - For AA Type)	-	0	ok
4(Grade - For MR grade)	-	0	ok
4(Grade - For BWR grade)	-	0	ok
cl. 13.1(marking)	-	0	ok
cl. 13.2(marking)	-	0	ok

28 Nov, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

Universal Testing and Research Centre (Division of Sustainable Stewardship Private Limited)

487/59, Ground Floor, Village Peeragarhi, National Market, New Delhi, West, Delhi, 110087

9810730485 lab@universaltesthouse.com

Scope List