BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List

Reset

367 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

361

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl- 13.5 (Conductor- Measurement of lay ratio/direction of lay)	-
Cl- 13.10 (Steel wires- Galvanizing test)	-
Cl-7 (Freedom From Defects)	-
Cl-9.2 (Aluminium Wires)	-
Cl-9.3 (Galvanized Steel Wires)	-
Cl-13.3 (Conductor- Visual examination)	-
Cl-13.4 (Aluminium wires-Measurement of diameter)	-
Cl- 13.4 (Steel wires- Measurement of diameter)	-
Cl- 13.5 (Conductor- Measurement of lay ratio/direction of lay)	-
Cl- 13.6 (Steel wires- Breaking load test)	-
Cl- 13.6 (Aluminium wires -Breaking load test)	-
Cl-13.7.1 (Torsion Test)	-
Cl-13.7.2 (Elongation Test)	-
Cl- 13.8 (Aluminium wires- Wrapping test)	-
Cl- 13.8 (Steel wires- Wrapping test)	-
Cl- 13.9 (Aluminium wires- d.c. resistance test)	-
Cl- 13.10 (Steel wires- Galvanizing test)	-
Cl- 13.11 (Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-
Cl- 13.12 (Conductor- d.c. Resistance test on stranded conductor)	-
Cl- 13.13 (Conductor- Surface condition test on stranded conductor)	-
Cl- 13.14 (Conductor- Ultimate tensile strength test on stranded conductor)	-
Cl- 13.15 (Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-
Cl-13.16 (Conductor- Radio interference voltage test)	-
Cl- 13.10 (Steel wires- Galvanizing test)	-
Cl-13.7.2 (Elongation Test)	-
Cl-13.7.1 (Torsion Test)	-
Cl-8.2 (Aluminum Conductors, Galvanized Steel- Reinforced)	-

-
"Partial: Up to 80 sq. mm-All Tests excluding Cl 13.15 Corona Test & Cl 13.16 Radio Interference Voltage Test. 100 sq mm and above-All tests excluding Cl 13.12 D.C Resistance test on stranded conductor, Cl 13.13 Surface Condition test, Cl 13.14 Ultimate Tensile Strength Test on Stranded conductor, Cl 13.15 Corona Test & Cl 13.16 Radio Interference Voltage Test."

362

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

For all grades except for the tests mentioned in remarks

25780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl 7.2 (Weight)	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
4.1 (Sulphur and phosphorous)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-
Clause - 4.2 & 4.2.1 (Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
8.18.1 Table 3 (Total elongation at maximum force)	-
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
4.2 (Niobium (Nb))	-
4.2 (Boron (B))	-
4.1 ( Ti)	-
Clause 4.2 Note 3, Amendment 1 & 3 (Cr+Cu+Ni+Mo+P)	-
Clause 4.2 Note 2, Amendment 1 & 3 (Nb+V+B+Ti)	-

-
Mech - Facility not available for pull out test, total elongation at maximum force. Chem- Declarations to be provided regarding type of 'Killed' material/Micro-alloys/low-alloys/Nitrogen content or any other parameter to be analysed additionally

363

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Complete for Cat 01(up to 400sq.mm)Except optional test

Rs 26700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.2 (INSULATION : Thickness of Insulation)	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
11.1 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
12.3.1 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1.e (Insulation resistance Test- Volume Resistivity At Room temperature)	-
15.1.e (Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance constant At Room temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
13.3 (Armouring : Dimensions -Formed wire )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
16.4 (Flammability Test)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
3.1 (MATERIALS : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.3 (Minimum Thickness of Reduce core insulation)	-
9.2 (Thickness of Reduce core insulation)	-
3.1 Table 2 IS 8130 (Number of wires in the conductor)	-

-
For Category-01 and upto 400 sq mm: all tests are available except additional tests. For cat. C1 and C2 : Except oxygen Index,Temperature index, Flame Retardance, Smoke Density,

364

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-
7 Table 1 i (Fineness IS 4031(Part 2))	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
Cl. 7 Table-2 (Cl. 7 Table-2 v (Transverse Strength (Optional) )	-
Cl. 7 Table-2 (Cl. 7 Table-2 ii a (Expansion after aeration ))	-

-
Mech-Facility not available for transverse strength test( optional); Chem-Declaration for chloride regarding end use of cement required as per Table 1, Confirmation for testing Alkali Content required.

365

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

All varieties

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.6 (Overall migration)	-
Cl-7.4 (Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-
8.2 (Longitudinal Reversion Test)	-
8.4 ( Melt Flow Rate)	-
8.8 (Tensile Strength for Butt-fusion)	-
8.9 table-6 (Elongation at Break)	-
Cl-7.4 (Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-
8.8 (Tensile Strength for Butt-fusion)	-
8.9 table-6 (Elongation at Break)	-
8.3 (Carbon black)	-
6.2.1 (6.1.1 Identification Stripes)	-
6.1.4 (PIPE DESCRIPTION)	-
Clause 7.1 (Visual Apperance)	-
6.2 (Colour)	-
Cl. 8.3 (Carbon Black Dispersion)	-
8.7 (Density)	-
8.5 (Oxidation Induction Time)	-
Cl-7.4 (Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-

-
Mech- Except Hydraulic test, Slow Crack Growth Rate and Internal Pressure Creep Rupture test. Fused pipes required to be provided for T/S of butt fusion joints. Prepared test pieces required for density. Chem- Complete

366

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- v (Transverse Strength - IS 4031 Part 8 (Optional))	-

-
Mech- Facility not available for transverse strength test( optional); Chem-Declaration for chloride regarding end use of cement (as per Table 1) and declaration of fly ash content & Confirmation for testing Alkali Content required.

367

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

Complete for Category 01- up to & including 400 sq mm

Please see remarks View breakup
Category: 01 Unsheathed cable: a) Single Core, Plain Copper Conductor - Rs.10500 b) Single Core, Tinned Copper Conductor- Rs.10800 c) Single Core, Solid Aluminium Conductor- Rs.10200 d) Single Core, Stranded Aluminium Conductor- Rs.10200 Sheathed Cable: a) Single Core, Plain Copper Conductor- Rs. 17550 b) Single Core, Tinned Copper Conductor - Rs.17850 c) Single Core, Solid Aluminium Conductor- Rs. 17250 d) Single Core, Stranded Aluminium Conductor- Rs.17250 Category: 02 Unsheathed cable: a) Single Core, Plain Copper Conductor- Rs.12150 b) Single Core, Tinned Copper Conductor- Rs.12450 c) Single Core, Solid Aluminium Conductor - Rs.11850 d) Single Core, Stranded Aluminium Conductor - Rs.11850 Sheathed Cable: a) Single Core, Plain Copper Conductor - Rs.18900 b) Single Core, Tinned Copper Conductor - Rs.19200 c) Single Core, Solid Aluminium Conductor - Rs.18600 d) Single Core, Stranded Aluminium Conductor - Rs.18600 Multi core cable: For each additional core, the charges of single core unsheathed cable as per material (copper and aluminium) and as per construction of conductor (solid or stranded, tinned or plain) shall be added

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Conductor - Material)	-
4.2 (Conductor resistance test)	-
5.1 (Insulation)	-
6.1 (Filler)	-
4.1 (Annealing test (for copper))	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Wrapping test (for Al))	-
10.11 (Per sulphate test (for tinned Cu cable only))	-
(Cl.16.1) (Cl.19.1) (Conductor- Diameter )	-
5.2 (Application )	-
6.2 (Filler)	-
7 (Binder Tape)	-
8.1 (Sheath Material )	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4) (Colour of Sheath)	-
9 (Overall dimensions)	-
9.1 (Ovality)	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
10.4 (Flammability test-Burning after flame removal)	-
10.4 (Flammability test- Unaffected portion)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
table 1 e) 3) (Volume Resistivity - Room temp )	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (IR constant- max. Temp)	-
10.1 (HV (water immersion))	-
10.1 (HV (water immersion))	-
10.2 (HV (room temperature))	-
11 (Identification)	-
11.1 (Durability)	-
11.2 (Legibility)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
8.3 (Avarage thickness of Sheath)	-
5.3 (Minimum thickness of insulation)	-
5.3 (Avarage thickness of insulation)	-
Table 2, IS 8130 (No fo wire in a conductor)	-
4, IS 8130 (Construction of conductor)	-
8.1 (Sheath Material )	-
12.0 (Core identification)	-
Table 1 (Category Code)	-
Table 4 (Copper purity test)	-
8.3 (Minimum thickness of Sheath)	-
4.4 (Joints in Conductor)	-
4.4 (Joints in Conductor)	-
10.11 (Persulphate Test )	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.6 (Halogen evolution)	-

-
Chem- Facility available for Cu purity only,Gr to be declared. Elect- Cat -01, 02 (Facility not available for- Loss of mass above 1.2 mm, Tensile & Elongation above 2.0 mm thickness.) Cat- FR, FR-LSH-( Facility not available for- oxygen index, temp. index test, Smoke Density Tests). Chem- Facility available for Cu purity only,Grade/class to be declared

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List