BIS - LIMS (Laboratory Information Management System)

Central Institute of Petrochemicals Engineering & Technology (CIPET), Murthal

CIPET-Murthal, Near DCRUST, Murthal, Sonipat, Sonipat, Sonipat, Haryana, 131039

22254780 murthal@cipet.gov.in

Scope List

Reset

43 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

21930 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	500	Nil
4.1(Raw Material)	-	2000	Nil
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	Nil
4.2(Tapes – Linear Density )	-	500	Nil
4.2(Construction)	-	500	Nil
4.3(Sacks)	-	500	Nil
4.3.1(Bottom Seam)	-	500	Nil
4.3.1(The two rows of stitches shall be separated from each other)	-	0	Test Charges Included in Bottom Seam Test
4.3.1( The outer stitch)	-	0	Test Charges Included in Bottom Seam Test
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	Test Charges Included in Bottom Seam Test
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	Test Charges Included in Bottom Seam Test
4.3.1(stitches/dm)	-	0	Test Charges Included in Bottom Seam Test
4.3.2(Mouth)	-	0	Test Charges Included in Bottom Seam Test
4.4(Liner IS 10146 or IS 10910.)	-	500	Nil
4.4(Mass of the loose liner )	-	500	Nil
4.4(Width of the loose liner)	-	500	Nil
4.4(Length of the line)	-	500	Nil
4.4(Bottom seam of the loose liner)	-	500	Nil
4.4.1(Liner)	-	500	Nil
4.5 and Table 1 i(Capacity)	-	500	Nil
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	Nil
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	Test Charges Included in Dimensions Inside Length Test
5.2 and Table 1 iii(Ends per dm )	-	500	Nil
5.2 and Table 1 iv(Picks per dm )	-	0	Test Charges Included in Ends per dm Test
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	Nil
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	Nil
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	Nil
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	Nil
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	Nil
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	Test Charges Included in Breaking Strength Test
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	Test Charges Included in Breaking Strength Test
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	U.V Light Exposure Charges RS.10180
5.2 and Table 1 x(Ash content )	-	1200	Nil
5.3(UV Resistance)	-	10180	-
Cl-4.4 (Amendment-3)(Thickness of liner)	-	500	-

09 Aug, 2028

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

21430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	Nil
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	Nil
4.2(Tapes – Linear Density )	-	500	Nil
4.3(Sacks)	-	500	Nil
4.3.1(Bottom Seam)	-	0	Charge included in sacks , cl.4.3
4.3.2(Mouth)	-	0	Charge included in sacks , cl.4.3
4.4 and Table 1 i(Capacity)	-	500	Nil
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	Nil
5.2 and Table 1 iii(Ends per dm )	-	500	Nil
5.2 and Table 1 iv(Picks per dm )	-	500	Nil
5.1 and Table 1 v(Mass of sack )	-	500	Nil
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	Nil
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	Nil
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	Rs. 10180 for UV Resistance exposure ( 192 hours).
5.2 and Table 1 x(Ash content )	-	1200	Nil
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	500	-

09 Aug, 2028

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

50 Kg

21430 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	Nil
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	700	Nil
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100	Nil
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	Nil
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	700	Nil
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	700	Nil
3.2(Unlaminated Fabric Mass )	-	500	Nil
3.3.1(Bottom seam (IS 10789))	-	1100	Nil
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	Nil
4.2 and Table 1 ii(Dimensions )	-	500	Nil
5.2 and Table 1 iii(Ends per dm )	-	500	Nil
5.2 and Table 1 iv(Picks per dm )	-	0	Ends & Picks including both test Charges is Rs. 250
4.2 and Table 1 v(Mass of sack )	-	500	Nil
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1100	U.V light Exposure Test Charges Rs. 10180
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	Nil
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Charge for the same is included with Breaking strength of fabric charges
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100	Nil
4.2 and Table 1 x(Ash content )	-	950	Nil
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	Nil
3.1(Material Identification)	-	1050	Test Method-Chemical Analysis
3.1(Overall Migration)	-	1700	Overall Migration Distilled water/10 days/40°C Specimen Charges Rs. 625
3.2(Density)	-	500	Nil
3.2(MFI)	-	1100	Nil

09 Aug, 2028

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

27680 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500	Nil
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500	Nil
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	Test Charges Included in Ends Test
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500	Nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	Test Charges Included in Dimension Test
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	Test Charges Included in Dimension Test
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	Test Charges Included in Dimension Test
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	Test Charges Included in Dimension Test
4.1(Raw Material )	-	2000	Nil
4.2 (Linear Density, 900 denier)	-	500	Nil
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	500	Nil
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500	Nil
4.3(Sacks)	-	500	Nil
4.4(Seam )	-	500	Nil
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	Test Charges Included in Seam Test
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	Test Charges Included in Seam Test
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	Test Charges Included in Seam Test
4.4(to a depth of minimum 25 mm, so that so that)	-	0	Test Charges Included in Seam Test
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	Test Charges Included in Seam Test
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	Test Charges Included in Seam Test
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	500	Nil
4.7(Valve for Filling of Sacks)	-	500	Nil
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	Nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	Nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	Nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	Charges included in Breaking Strength
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	Charges included in Breaking Strength
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	Nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200	Nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	1200	Nil
5/5.6 (UV Resistance, )	-	10180	Nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1100	Nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100	Nil
4.5(Lamination )	-	500	Nil
4.2 (Fabric)	-	500	-

09 Aug, 2028

-
-

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

21690 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	2000	Nil
3.2(Tapes – Width )	-	500	Nil
3.2(Tapes – Linear Density )	-	500	Nil
3.3(Tying Cord)	-	500	Nil
3.4(Sack)	-	500	Nil
3.4.1(Seam)	-	500	Nil
4.1 and Table 1 i a(Dimensions Outside Length)	-	500	Nil
4.1 and Table 1 i b(Dimensions Outside Width)	-	500	Nil
4.1 and Table 1 ii(Ends per dm )	-	500	Nil
4.1 and Table 1 iii(Picks per dm )	-	0	Test Charges included in Ends per dm
4.2 and Table 1 iv(Mass of sack )	-	500	Nil
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	Nil
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	Nil
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	Nil
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	Test Charges included in Breaking strength
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	Test Charges included in Breaking strength
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12540	UV light exposure Rs. 10340 Breaking strength (warp & weft)
4.1 and Table 1 ix(Ash content )	-	1200	Nil
3.2 (Mesh size and weight is g/cm2) (amendment 3)(Mesh size and weight is g/cm2)	-	500	-

09 Aug, 2028

-
-

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

122250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Designation)	-	500	Nil
Cl 7(Dimensions Of Pipes)	-	500	Nil
Cl 9.1(Hydraulic Characteristics)	-	18400	Acceptance Test (1 h. / 20˚ C) Acceptance Test (22 h. / 95˚ C) Type test ( 165 h. / 95˚ C) Type test ( 1000 h. / 95˚ C) Type test ( 165 h. / 95˚ C)
Cl 9.3(Reversion Test )	-	1200	Testing Charges- 700 Specimen Charges-500
Cl 9.4 & Annex B(Impact Strength)	-	1600	Testing Charges- 1100 Specimen Charges-500
Cl 9.5(Density)	-	700	Nil
Cl 9.6(Melt Flow Rate)	-	1100	Nil
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	Carbon Black content Rs 925 Carbon Black dispersion Rs 700
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	Thermal Stability by Hydrostatic Pressure (8760 h./110 °C)*
Cl 9.9(Opacity)	-	700	Nil

09 Aug, 2028

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

22250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	900	Nil
4.2.3(Carbon Dispersion Test)	-	650	Nil
5(Types and Features )	-	500	Nil
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Nil
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	Nil
5.3(Types and Features )	-	0	Test charges included in Types and Features
5.6(Types and Features )	-	0	Test charges included in Types and Features
6.1(Finish)	-	500	Nil
7.1.1(Resistance to Deformation)	-	700	Nil
7.1.2(Resistance to Deformation)	-	1100	Nil
7.2(Resistance to Impact)	-	1000	Nil
7.3(Test for Top Load Resistance)	-	900	Nil
7.4(Tensile Strength)	-	1800	Testing Charges- 1300 Specimen Charges-500
7.5(Flexural Modulus)	-	1600	Testing Charges- 1100 Specimen Charges-500
7.6(overall Migration)	-	2200	Testing Charges- 1700 Specimen Charges-500
9.2.1(Man-Hole and Hand-Hole Lids)	-	500	Lid Lock up & Lid Clearance Dimension
9.2(Man-Hole and Hand-Hole Lids)	-	0	Test Charges included in Man-Hole and Hand-Hole Lids
9.1(Man-Hole and Hand-Hole Lids)	-	0	Test charges included in above CBC & CBD Test.
9.1(Lid Thickness)	-	500	Nil
5.4(Wall Thickness above effective height)	-	500	Nil
5.2 Table 2 (7)(Minimum Wall Thickness)	-	500	Nil
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	Nil
4.2.1(Density)	-	1325	Testing Charges- 700 Specimen Charges-625
4.2.2(MFI)	-	1000	Nil
7.6(overall Migration)	-	0	Test charges included in overall Migration test (above)

09 Aug, 2028

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

12900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	500	Nil
5.1(Materials)	-	2000	Nil
5.2(Black Compound)	-	1550	CBC 900 CBD 650
6.1.1(Appearance)	-	500	Nil
6.1.2(Film Form)	-	0	Test Charges Included in Appearance
6.1.3(Odour )	-	0	Test Charges Included in Appearance
6.1.4(Density)	-	700	Nil
6.1.5(Melt Flow Rate)	-	1100	Nil
6.1.6(Black Film)	-	1625	CBC 925 CBD 700
6.2.1, Table 1(Nominal Thickness)	-	500	Nil
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Nominal Thickness
6.2.2, Table 2(Nominal Width)	-	500	Nil
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Nominal Thickness
6.3, Table 3(Yield Tolerance)	-	600	Nil
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Yield Tolerance
6.4.1(Tensile Strength at Break)	-	2600	MD 1300 TD 1300
6.4.1, Table 4(Direction)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2(Elongation at Break)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2, Table 5(Direction)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0	Test Charges Included in Tensile Strength at Break
6.4.3(Impact Resistance (Falling Dart))	-	800	Nil
6.4.3, Table 6(Average Thickness of Film)	-	500	Nil

09 Aug, 2028

-
-

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

16350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	Nil
9.5(Tensile Strength IS 12235(Part 13))	-	1800	Testing Charges- 1300 Specimen Charges-500
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	Testing Charges- 1000 Specimen Charges-500
9.3(Density IS 12235 (Part 14))	-	700	Nil
9.2(Internal Diameter)	-	500	Nil
9.1( Visual Appearance)	-	500	Nil
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	Nil
8.4(Sealing rings - Hardness)	-	500	Nil
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	500	Nil
7.3.2(Rib height)	-	500	Nil
7.3.1(No.of Ribs)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	500	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	500	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	500	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	500	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	500	Nil
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	500	Nil
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	950	Nil
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	2750	Nil
5.0(Colour of Pipes)	-	500	Nil
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	Nil
4.1.2(K-Value as per IS-4669)	-	1000	Nil

09 Aug, 2028

-
-

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

7228 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	Nil
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	1200	Nil
3.2.1, Table-1, Fig-1(Nominal size)	-	500	Nil
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	500	Nil
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	500	Nil
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	500	Nil

09 Aug, 2028

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

8470 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	1050	Nil
4(Size of fitting)	-	500	Nil
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	Nil
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	Test Charges included in Dimension of Socket length
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	Test Charges included in Dimension of Socket length
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	Nil
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850	Nil
3.2.3(socket, measurements)	-	0	Test Charges included in Dimension of Socket length
6.3(Effect on water test)	-	3000	Nil

09 Aug, 2028

-
-

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

8403 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	500	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	500	charge is included in Cl. 4 charge
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	Charge is included in Cl. 4 charge
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	charge is included in Cl. 4 charge
Cl. 6.1(Stress Relief Test- Appendix A)	-	700	-
Cl. 6.2(Opacity- Appendix B)	-	700	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	3000	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	Charge is included in Cl. 6.3 first extraction
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	Charge is included in Cl. 6.3 first extraction
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	Charge is included in Cl. 6.3 first extraction
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	850	-

09 Aug, 2028

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

upto DN 400 mm

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500		-
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	500		RS 1500subject to minimum test charges

09 Aug, 2028

-
-

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

Diameter upto 20 mm to 400 mm

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500	-
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	500	-
3.2.3(Socket, measurements)	-	500	-

09 Aug, 2028

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

Upto DN 400 mm

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500	-
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	500	-
3.2.3(Socket, Measurement)	-	500	-
3.1(General)	-	5050	6.1 Opacity - Rs 700 6.2 Short term Hydraulic test (27 °C/1h.) Rs 850+Rs500 6.3 Effect on Water Rs. 3000

09 Aug, 2028

-
Upto 400mm

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Class 1 to 6 and DN 20 to 400 mm

32200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.7(Sulphated Ash Content)	-	1200	Nil
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	Nil
10.1(Colour)	-	300	Nil
10.1(Surface Finish)	-	300	Nil
7.2.1.1 Table3(Angle of taper (Note-1))	-	250	Nil
5(CLASSIFICATION OF PIPES)	-	300	Nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	Nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	Included in 7.1.1.1
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	Included in 7.1.1.1
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	Included in 7.1.1.1
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	Included in 7.1.1.1
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Included in 7.1.1.1
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	Included in 7.1.1.1
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	Included in 7.1.1.1
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	Included in 7.1.1.1
7.2.1(DIMENSIONS-Socket)	-	0	Included in 7.1.1.1
7.2.1(DIMENSIONS-Socket)	-	0	Included in 7.1.1.1
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	Included in 7.1.1.1
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	Included in 7.1.1.1
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	Included in 7.1.1.1
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	Included in 7.1.1.1
8(SEALING RINGS)	-	300	Nil
9.1(PIPE ENDS)	-	300	Nil
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	Nil
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	1100	Nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1200	700 test charge +500 sample preparation
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	Nil
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	Nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	Nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	Nil
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	Nil
11.2(Resistance to External Blows at 0°C)	-	1500	1000 test charge +500 sample preparation
6.1.2(PVC Resin)	-	1100	Nil
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	Nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	300	Nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	Nil
10.3(Effect on Water Test)	-	3000	Nil
7.1.4(Length)	-	250	Nil
6.1.1(VCM Content)	-	3000	Nil
7.2.1.2b(Maximum inner diameter of groove)	-	250	Nil
13.1(Marking)	-	250	Nil

09 Aug, 2028

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

A & B

29821 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	Nil
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	Nil
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	Nil
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Test Charges included in Dimension Test
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Test Charges included in Dimension Test
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	Test Charges included in Dimension Test
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Test Charges included in Dimension Test
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Test Charges included in Dimension Test
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	500	Nil
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1300	Testing Charges- 700 Specimen Charges-500
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	Nil
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	Nil
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	23600	Effect on sunlight by weatherometer for 1600 hrs(116175) charges -21800 Testing Charges- 1300 Specimen Charges-500
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	Testing Charges- 2000 Specimen Charges-500
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1600	Testing Charges- 1100 Specimen Charges-500
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1800	Testing Charges- 1300 Specimen Charges-500
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	850	Nil
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	Nil
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	Nil
8.6(Effect on Water Test)	-	3000	Nil

09 Aug, 2028

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

49825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000	Testing Charges- 5500 Specimen Charges-500
8.9 table-6(Elongation at Break)	-	1800	Testing Charges- 1300 Specimen Charges-500
8.8(Tensile Strength for Butt-fusion)	-	1800	Testing Charges- 1300 Specimen Charges-500
8.7(Density)	-	700	nil
8.5 (Oxidation Induction Time)	-	2200	nil
8.4( Melt Flow Rate)	-	1100	nil
8.2(Longitudinal Reversion Test)	-	1200	Testing Charges- 700 Specimen Charges-500
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	nil
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21900	Testing Charges- 21400 Specimen Charges-500
7.4.1.2(Ovality)	-	500	nil
7.4 table -3 & 4(6.1 Dimensions)	-	500	nil
7.2(Length)	-	500	nil
6.2.1(6.1.1 Identification Stripes)	-	500	nil
6.2(Colour)	-	500	nil
6.1.4(PIPE DESCRIPTION)	-	0	nil
6.1.3 (PIPE DESCRIPTION)	-	0	nil
6, 6.1.2(PIPE DESCRIPTION)	-	0	nil
6, 6.1.1(PIPE DESCRIPTION)	-	0	nil
6, 6.1(PIPE DESCRIPTION)	-	0	nil
8.6(Overall migration)	-	2200	Testing Charges- 1700 Specimen Charges-500
8.3(Carbon black)	-	925	nil
5.3(e)(Carbon Black Master Batch)	-	925	nil
5.3(d)(Carbon Black Master Batch)	-	925	nil
5.3(c)(Carbon Black Master Batch)	-	925	nil
5.3(b)(Carbon Black Master Batch)	-	925	nil
5.3 (a)(Carbon Black Master Batch)	-	925	nil
5.2(Polyethylene Resin)	-	2000	nil
5, 5.1 table-1(MATERIALS)	-	2000	nil
5.2(Density)	-	700	nil
5.2(MFI @ 1900C/5.0 Kg)	-	1100	nil
5.2(Volatile matter Content)	-	925	nil
5.3(Toluene Extract)	-	1100	nil

09 Aug, 2028

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	500	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	Refer above cost ( including all dimension cost)
2.2.3( inside diameter of the socket)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3(Socket length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .

09 Aug, 2028

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	500	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3( inside diameter of the socket)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3(Socket length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .

09 Aug, 2028

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	500	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.2, Table 1(Socket Laying Length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3( inside diameter of the socket)	-	0	Included in above given cost
2.2.3(Socket length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .

09 Aug, 2028

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2, Table 1(Size)	-	500	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.2, Table 1(Union Laying Length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3( inside diameter of the socket)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .
2.2.3(Socket length)	-	0	Complete testing charge is Rs. 1500 as minimum Charge is Rs.1500 + tax .

09 Aug, 2028

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2.2(diameter of the socket of cap)	-	500		minimum charge is Rs. 1500 & GST Extra

09 Aug, 2028

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	500	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	included in above given effect on water charge
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	included in above given effect on water charge
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0	included in above given effect on water charge

09 Aug, 2028

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.2, Fig 1(Dimensions)	-	500		-
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500		Rs. 1500 subject to minimum test charges

09 Aug, 2028

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.2, Fig 1(Dimensions)	-	500		-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500		Rs. 1500 subject to minimum test charges

09 Aug, 2028

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

1500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.2, Fig 1(Dimensions)	-	500		-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	500		Rs 1500 subject to minimum test test charges

09 Aug, 2028

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500	-
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	500	-

09 Aug, 2028

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Materials)	-	2000	-
3.3.2, table 1, fig 1(Dimensions)	-	500	-
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	500	-

09 Aug, 2028

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	500	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	500	-

09 Aug, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Central Institute of Petrochemicals Engineering & Technology (CIPET), Murthal

CIPET-Murthal, Near DCRUST, Murthal, Sonipat, Sonipat, Sonipat, Haryana, 131039

22254780 murthal@cipet.gov.in

Scope List