BIS - LIMS (Laboratory Information Management System)

Unique Test House

VILLAGE:-SARSINI, PO:-LALRU, Tehsil Derabassi, MOHALI, S.A.S Nagar, Punjab, 140501

9896169971 -

Scope List

Reset

82 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

ALL SIZE TYPE GRADE

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	500	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	500	-
Cl. 4 (b)(Condition - IS 737)	-	500	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	200	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	500	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	500	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	500	-
Cl. 4 (g)(Packing Mode - IS 737)	-	500	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	500	-
Cl. 6(Freedom from Defects - IS 737)	-	1000	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	700	-
Cl. 7(Al - IS 504)	-	1000	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	2000	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	700	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	1500	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	500	-
Cl. 8.2(Bend Test - IS 1599)	-	700	-
Cl. 9(Condition - IS 737/ IS 5052)	-	500	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	500	-
Cl. 11(Selection of Test Samples - IS 737)	-	500	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	500	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	200	-
Cl. 12(Retests - IS 737/ IS 10259)	-	100	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	200	-
Cl. 13.1(Marking - IS 737)	-	100	-

Complete

07 Sep, 2025

-
Included w.e.f.28.03.2025

IS 6528 (2024)

Stainless steel wire - Specification ( Second Revision )

ALL SIZE / GRADE EXCEPT X04Cr18Ni10Ti,X07Cr21Ni11SiNCe,X01Cr25Ni21,X01Cr25Ni20,X12Cr25Ni20,X04Cr25Ni20, X15Cr25Ni21Si,x04Cr17Ni12Mo2Ti,X01Cr20Ni18Mo6CuN,X01Cr25Ni22Mo2,X01Cr24Ni22Mo4CuNW,X01Cr24Ni22Mo7CuN,X02Cr25Ni18Mn6Mo4N,X01Ni25Cr20Mo5Cu,

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 6(FREEDOM FROM DEFECTS)	-	700	ALL SIZE / GRADE EXCEPT X04Cr18Ni10Ti,X07Cr21Ni11SiNCe,X01Cr25Ni21,X01Cr25Ni20,X12Cr25Ni20,X04Cr25Ni20, X15Cr25Ni21Si,x04Cr17Ni12Mo2Ti,X01Cr20Ni18Mo6CuN,X01Cr25Ni22Mo2,X01Cr24Ni22Mo4CuNW,X01Cr24Ni22Mo7CuN,X02Cr25Ni18Mn6Mo4N,X01Ni25Cr20Mo5Cu,
As per clause 7(CARBON)	-	500	Except grade X01Ni25Cr20Mo7CuN,X8NiCAlTI32-21,X01Ni31Cr27MO4Cu, X03Cr27NiMO2N,X02Cr25Ni6Mo3CuN, x02Cr25Ni7Mo4N, X02Cr25Ni7Mo4CuWN, X04Cr13,X03Cr17Nb,X02Cr18TiNb,X04Cr17Mo1,X02Cr18Mo2TiS, X05Cr16Ni4CuNb, X07Cr17Ni7AI
As per clause 7(SILICON)	-	500	-
As per clause 7(MANGANESE)	-	500	-
As per clause 7(PHOSPHORUS)	-	500	-
As per clause 7(SULPHUR)	-	500	-
As per clause 7(CHROMIUM)	-	1000	-
As per clause 7(MOLYBEDNUM)	-	1000	-
As per clause 7(NICKEL)	-	1000	-
As per clause 7(NITROGEN)	-	2000	-
As per clause 7(COPPER)	-	500	-
As per clause 7(NIOBIUM)	-	1000	-
As per clause 7(TITANIUM)	-	11000	-
As per clause 7(ALUMINIUM)	-	1000	-
As per clause 8(HEAT TREATMENT)	-	500	-
As per clause 9(Dimension Tolerance)	-	500	-
As per clause 10(TENSILE TEST)	-	2000	-
As per clause 10.2(REVERSE BEND TEST)	-	1000	-
As per clause 10.3(TORSION TEST)	-	1000	-
As per clause 14(FINISH)	-	1000	-
As per clause 15(CORROSION RESISTANCE)	-	3000	-
As per clause 16.2(MARKING)	-	1000	-

Complete

07 Sep, 2025

-
Included w.e.f.27.03.2025

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

UPTO 1000 MM

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(VALVE END CONNECTIONS)	-	200	-
6.0( NOMINAL SIZES )	-	200	-
7.0(NOMINAL PRESSURES)	-	100	-
7.2(Class designations)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Bolting )	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-f)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Bolting)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -k)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Bolting)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling - Nos.)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -d2)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -k)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange -D)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange - b)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - d4)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - f)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Bolting)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-	100	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-	100	-
9.1.1 ( Double Flanged Body Ends)	-	100	-
9.2.2(Wafer Body Ends)	-	100	-
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-	200	-
11.0(Bodies)	-	100	-
12.0(DISC AND SHAFT)	-	200	-
13.0(SEATING AND LININGS)	-	200	-
14.0(BEARINGS)	-	100	-
14.2(BEARINGS)	-	100	-
14.3(BEARINGS)	-	200	-
16.0(OPERATION)	-	100	-
17.1(Performance Testing)	-	100	-
17.2(Body Test)	-	200	-
17.3(Seat Test)	-	100	-
17.4(Disc Strength Test)	-	200	-
Cl. 15 Table 2(Materials)	-	100	-
5.0(SERVICE APPLICATIONS)	-	200	-

Complete

07 Sep, 2025

-
-

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Upto600mm( 600mmto2540mmwithout h.s.t) /FE 330toFE450

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Hydaulic pressure test)	-	1500	---
12.3.3(Ovality)	-	500	...
8.1 Table 2 Table 3(Carbon Content IS 228)	-	800	....
8.1 Table 2 Table 3(Manganese Content IS 228)	-	800	....
8.1 Table 2 Table 3(Phosphorus Content IS 228)	-	800	....
8.1 Table 2 Table 3(Sulphur Content IS 228)	-	800	...
9.3(Guided bend test(For SAW Pipes))	-	800	...
11.1, Table 5.(Outside Diameter (OD))	-	500	...
11.1, Table 5.(Thickness)	-	500	...
11.1, Table 5.(Mass)	-	500	...
12.5(Strightness)	-	500	...
14.1(Visual inspection, Appearance and Workmanship)	-	200	...
8.1(CE)	-	800	....
9.2.3(Flattening Test for seamless pipes)	-	800	-
9.2.1(Flattening test for ERW pipes )	-	800	-
9.1(Tensile test-Yield Strength)	-	500	....
9.1(Tensile test-Strength)	-	800	...
9.1(Tensile test- Elongation)	-	800	...
14.2(Visual inspection, Appearance and Workmanship)	-	200	-
14.3(Visual inspection, Appearance and Workmanship)	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	200	-

Complete

07 Sep, 2025

-
-

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

ALL SIZE /GRADE TYPE

14000 View breakup
-

Complete

07 Sep, 2025

-
Included w.e.f.20.03.2025

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

ALL GRADE /TYPE/ SIZE

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	200	-
6.1(Marking, IS 9537-2)	-	500	-
6.1(Marking, IS 9537-2)	-	500	-
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	500	-
6.2(Marking, IS 9537-2)	-	500	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	500	-
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	200	-
7.3(Dimensions (Wall thickness), IS 9537-2)	-	200	-
7.3.3(Uniformity of wall thickness, IS 9537-2)	-	300	-
7.4(Screw threads, IS 9537-2)	-	300	-
8.1(Construction, Cl. 8 of IS 9537-1)	-	200	-
8.2(Construction, IS 9537-2)	-	200	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	2000	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	2500	-
13(External Influences, IS 9537-2)	-	200	-
Cl 13.4.5(External Influence ( Outside tube))	-	200	-
Cl 13.4.6(External Influence ( Inside tube))	-	500	-
7.1(Dimensions)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f. 05.03.2025

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

ALL GRADE TYPE DESIGNATION AND SIZE

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Types /Grade and Designation)	-	500	-
As per clause 6(Material)	-	100	-
As per clause 7(Manufacture)	-	200	-
As per clause 7.1.5(Sulphur)	-	800	-
As per clause 7.1.6(Phosphorus)	-	800	-
As per clause 8(Mechanical Properties)	-	200	-
As per clause 8.1(Tensile Test)	-	700	-
As per clause 8.1.1(Yield Stress)	-	700	-
As per clause 8.1.2(Elongation)	-	700	-
As per clause 8.2(Drift Expansion Test)	-	1000	-
As per clause 8.3(Flattening Test)	-	1500	-
As per clause 9(Weight)	-	700	-
As per clause 10(Hardness Test)	-	1000	-
As per clause 11(Mechanical Test)	-	1500	-
As per clause 12(Retests)	-	1500	-
As per clause 13(Dimension Tolerance)	-	500	-
As per clause 14(Workmanship)	-	200	-
As per clause 15(Straightness)	-	800	-
As per clause 16(Length)	-	200	-
As per clause 17(Surface Protection)	-	500	-
As per clause 18(Marking)	-	500	-

Complete

07 Sep, 2025

-
-

IS 3989 (2024)

CENTRIFUGALLY CAST (SPUN) IRON SPIGOT AND SOCKET PIPES, FITTINGS AND ACCESSORIES ï¿½ SPECIFICATION (Fourth Revision)

All sizes

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3(General requirements)	-	2000	-
Cl-4(MATERIALS AND MANUFACTURE)	-	1000	-
Cl-5(HAMMER TEST)	-	1500	-
Cl-6(HYDROSTATIC TEST)	-	2500	-
Cl-7(SIZES)	-	1000	-
Cl-8(TOLERANCES)	-	500	-
Cl-8.1 (i)(External diameter of barrel, DE)	-	500	-
Cl-8.1 (ii)(Internal diameter of socket, DI)	-	1000	-
Cl-8.1 (iii)(Depth of socket, P)	-	500	-
Cl-8.2(Tolerance on length)	-	500	-
Cl-8.3(Tolerances on dimensions)	-	500	-
Cl-8.4(Tolerance on wall thickness)	-	500	-
Cl-9(Coating)	-	1000	-
Cl-10(Marking)	-	500	-

Complete

07 Sep, 2025

-
Included.w.e.f.31.01.2025

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

ALL SIZES GRADE AND DESIGNATIONS

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	700	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	500	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	500	-
14(Reverse Flattaning Test)	-	500	-
15(Flattaning Test-IS 2328)	-	1000	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	500	-
18(Leak Tighteness Test)	-	2000	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	2000	-
22(Workmanship, Finish and Appearance)	-	200	-
23(Repair by Welding or Grinding)	-	500	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	1000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	2000	-
Clause 10.1 - Table 4(Tensile Strength)	-	1000	-
Clause 10.1 - Table 4(Yield Strength)	-	1000	-
Clause 10.1 - Table 4(Percent Elongation)	-	1000	-
Clause 11(Transverse Tension Test)	-	1000	-
Clause 12(Hardness Test)	-	500	-
Clause 13(Flange Test)	-	500	-
Clause 14(Reverse Flattening Test)	-	500	-
Clause 15(Flattening Test)	-	500	-
Clause 16(Grain Size)	-	500	-
Clause 18()	-	500	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	2000	-
Clause 22(Workmanship, Finish & Appearance)	-	500	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	500	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	500	-
12.2(Hardness test)	-	500	-
17(Sampling)	-	200	-
25(Marking)	-	200	-
6.7, Table 7, ii)(c) Chromium VI)	-	500	-

Complete

07 Sep, 2025

-
Included.w.e.f.31.01.2025 Exclusion Cl 8.1 & 8.2 (Table no.-1) (Tungstun (W) Cl 20 (Eddy current test, air under water tests, Rediographic tests)

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

ALL SIZE GRADE DESIGNATION

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	700	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1500	-
13 (Table No.- 7)(Flaring Test)	-	500	-
14(Flattaning Test-IS 2328)	-	500	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	500	-
17(Leak Tighteness Test)	-	3000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	3000	-
19(Eddy current test & Air under water)	-	1000	-
21(Workmanship, Finish and Appearance)	-	500	-
22(Repair by Welding or Grinding)	-	500	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	3000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	700	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	2000	-
Clause 10.1 - Table 4(Tensile Strength)	-	1000	-
Clause 10.1 - Table 4(Percent Elongation)	-	500	-
Clause 11(Transverse Tension Test)	-	500	-
Clause 12(Hardness Test)	-	1000	-
Clause 13(Flaring Test)	-	500	-
Clause 14(Flattening Test)	-	500	-
Clause 15(Grain Size)	-	500	-
Clause 17(Leak Tightness Test)	-	500	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	2000	-
Clause 21(Workmanship, Finish & Appearance)	-	500	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	500	-
10.2(Hardness test IS 1500 (part-1):2019)	-	1000	-
12.2(Flaring test IS 17878:2022)	-	500	-
16(Sampling)	-	500	-
24(Marking)	-	200	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	500	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	500	-

Complete

07 Sep, 2025

-
Included.w.e.f.31.01.2025

IS 2191 : Part 2 (2022)

WOODEN FLUSH DOOR SHUTTERS (CELLULAR, HOLLOW AND TUBULAR CORE TYPE) - SPECIFICATION PART 2 PARTICLE BOARD, HIGH DENSITY FIBRE BOARD, MEDIUM DENSITY FIBRE BOARD AND FIBRE HARDBOARD FACE PANELS (Fourth Revision)

ALL SIZE /TYPE/GRADE /DESIGNATION

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Sizes and Tolerances)	-	500	-
Cl-6.1.(Timber)	-	1000	-
Cl-6.2(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), medium density fibre board (MDF), high density fibre board (HDF))	-	2500	-
Cl-6.3.1(Particle board)	-	2500	-
Cl-6.3.2(MDF board and HDF board)	-	2500	-
Cl-6.3.5(shutters with fibre hardboard face)	-	2500	-
Cl-8.1(Locks)	-	500	-
Cl-10.1(various test)	-	15000	-
Cl-10.2(End Immersion Test)	-	3000	-
Cl-10.3(Glue Adhesion Test)	-	2500	-
Cl-13(Marking)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f.18.12.2024

IS 2191 : Part 2 (1983)

Specification for wooden flush door shutiers (Cellular And Hollow Core Type): Part 2 particle board and hardboard pace panels

All

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3 (Table-2)(Size- Height)	-	500	-
Cl. 3 (Table-2)(Size- Width)	-	500	-
Cl. 3.2 (Nominal thickness of shutters)	-	500	-
Cl. 4.1(Timber)	-	10000	-
Cl. 4.2(Particle Board)	-	3500	-
Cl. 4.3(fibre Hardboard)	-	3500	-
Cl. 4.4(Adhesive)	-	9500	-
Cl. 5(CONSTRUCTION)	-	1000	-
Cl. 5.2(Face Panel)	-	1000	-
Cl. 6(FITTINGS)	-	1000	-
Cl. 6.1(Locks)	-	1000	-
Cl. 7(WORKMANSHIP AND FINISH)	-	500	-
Cl. 8.1(End immersion Test)	-	3500	-
Cl. 8.2(Knife Test)	-	2000	-
Cl. 8.3(Adhesion Test)	-	2500	-

Complete

07 Sep, 2025

-
Included w.e.f 06.12.2024

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	300	-
Clause - 7.1(SULPHUR)	-	300	-
Clause - 7.1(PHOSPHURS)	-	300	-
Clause - 7.1(MANGANESE)	-	300	-
Clause - 7.1(NITROGEN)	-	4000	-
As per Clause 10(Dimension)	-	200	-
As per Clause 10.1(Dimension Width)	-	300	-
As per Clause 10.1(Dimension Thickness)	-	300	-
As per Clause 10.2(Dimension Length)	-	300	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	200	-
As per Clause 11.5(Bend)	-	500	-
As per Clause 11.6(Camber)	-	300	-
As per Clause 11.7 (i)(Out of Square)	-	300	-
As per Clause 11.7 (ii)(Round Corners)	-	300	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	300	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	300	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	300	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	300	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	300	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	300	-
As per Clause 11.7 (ix)(Scarfing pits)	-	300	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	200	-
Clause. 13(Macro examination test.)	-	500	-
Clause. 13(Macro examination test.)	-	500	-
Clause. 14(Marking)	-	200	-
Clause.15(Ordering information)	-	200	-
Clause.6.0(Manufacture)	-	200	-
Clause.7.1(Silicon)	-	300	-
Clause.7.1(Carbon Equbalant)	-	300	-
Clause.7.1(Microalloy element)	-	300	-

Complete

07 Sep, 2025

-
Included w.e.f. 29.11.2024 Exclusion: Clause. 13 (Sulphur print, INCLUSION CONTENT)

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 5.2, 9 and 10.2.2(Density)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Variation from mean density)	-	100	-
Clauses 5.2, 9 and 10.2.2(Moisture Content)	-	1000	-
Clauses 5.2, 9 and 10.2.2(Variation from mean moisture content)	-	100	-
Clauses 5.2, 9 and 10.2.2(Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-	1500	-
Clauses 5.2, 9 and 10.2.2(Internal Bond Strength)	-	2000	-
Clauses 5.2, 9 and 10.2.2(Internal Bond strength (i) (After Cyclic test) (ii) (After accelerated water resistance test))	-	2500	-
Clauses 5.2, 9 and 10.2.2(Modulus of Rupture a) Avg. Value b) Min. Individual)	-	2000	-
Clauses 5.2, 9 and 10.2.2(Modulus of Elasticity a) Avg. Value b) Min. Individual)	-	2000	-
Clauses 5.2, 9 and 10.2.2(Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-	2500	-
Clauses 5.2, 9 and 10.2.2(Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	3000	-
8(DIMENSIONS AND TOLERANCES)	-	500	-
Cl-11(ADDITIONAL REQUIREMENTS FOR ECO-MARK)	-	200	-
Clauses 5.2, 9 and 10.2.2(Density)	-	1000	-

Complete

07 Sep, 2025

-
Included w.e.f. 29.11.2024 Exclusion: Clauses 5.2, 9 and 10.2.2 (Steady State Formaldehyde emission (Fc (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

ALL SIZE/DESIGNATION /CONDITION/ETC

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Freedom from defects)	-	500	-
6.1 Table-1(Cu)	-	700	-
6.1 Table-1(Pb)	-	700	-
6.1 Table-1(Fe)	-	700	-
6.1 Table-1(Total impurities including iron)	-	100	-
6.1 Table-1(Zn)	-	700	-
7.1.1(Tensile Test)	-	1500	-
Table-2(Thickness)	-	100	-
Table-2(Tensile Strength)	-	1000	-
Table-2(Elongation)	-	500	-
Table-2(Vickers Hardness)	-	500	-
Table-2(Transverse Bend)	-	500	-
Table-2(Longitudinal Bend)	-	200	-
7.1.1(Erichsen cupping values -IS 410)	-	100	-
7.1.5(Grain Size - IS 410)	-	100	-
8(Dimensions -IS 410)	-	200	-
11(Marking)	-	100	-
7.1.1(Erichsen cupping values -IS 410)	-	500	-
7.1.5(Grain Size - IS 410)	-	1500	-
8(Dimensions -IS 410)	-	100	-
11(Marking)	-	100	-

Complete

07 Sep, 2025

-
Included.w.e.f.13.01.2025

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

ALL SIZE /DESIGNATION ETC

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2000	-
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
9( FREEDOM FROM DEFECTS)	-	500	-
10.1.a)( Macro examination IS 11371)	-	500	-
10.1.b)( Sulphur print tests IS 12037)	-	500	-
11 & 12(DIMENSIONS and Tolerances)	-	500	-
11(Dimensions)	-	200	-
10.2(Bend)	-	500	-
10.3(Chamber)	-	200	-
11(Dimensions)	-	200	-
10.2(Bend)	-	500	-
10.3(Chamber)	-	200	-
Clause 6.1.1(IS 2831 : 2012)	-	200	-
Cl. 11, 12 Table 3(Thickness )	-	200	-
Cl. 11, 12 Table 3(Width Across Flat)	-	200	-
Clause 9.4(Camber)	-	200	-
Clause 9.3(Bend)	-	500	-
Clause 6.1.1(By calculation)	-	100	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	100	-
Clause 6.1.1(By calculation)	-	100	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	500	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	500	-
Clause 6.1.1(Carbon Equivalent (CE))	-	500	-
Table 1 Note 2(Nb+V+Ti)	-	100	-
8(Selection of Test sample)	-	100	-
13(Marking)	-	100	-
Clause 6.1.1(Carbon Equivalent (CE))	-	100	-
Table 1 Note 2(Nb+V+Ti)	-	200	-

Complete

07 Sep, 2025

-
Included w.e.f. 29.11.2024

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

ALL SIZE /GRADE/ DESIGNATIONS /TYPES

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	100	-
Cl 10.1(Workmanship)	-	100	-
Cl 10.2(Workmanship)	-	100	-
Cl 10.2(Press)	-	100	-
Cl 10.3(Workmanship)	-	100	-
Cl 11(Length, Width & Thickness)	-	100	-
Cl 9(Workmanship)	-	100	-
Cl 10.1.a)(Workmanship)	-	100	-
Cl 10.1.b)(Workmanship)	-	100	-
Cl 10.2(Press)	-	100	-
Cl 10.3(Workmanship)	-	100	-
Cl 11(Length, Width & Thickness)	-	500	-
Cl 9(Workmanship)	-	100	-
Cl 10.1(Workmanship)	-	100	-
Cl 10.2(Workmanship)	-	100	-
Cl 10.2(Press)	-	500	-
Cl 10.3(Workmanship)	-	100	-
Cl 11(Length)	-	100	-
6.1(Carbon %)	-	700	-
6.1(Manganese %)	-	700	-
6.1(Phosphorus %)	-	700	-
6.1(Sulphur %)	-	700	-
6.1(Silicon %)	-	700	-
6.1( Copper %)	-	700	-
6.1( Aluminium %)	-	700	-
6.1( Nb)	-	700	-
6.1(V)	-	700	-
6.1( Ti)	-	700	-
6.1(Cr)	-	700	-
6.1(Mo)	-	700	-
6.1(Ni)	-	700	-
6.1( Nitrogen%)	-	2000	-
6.1(Carbon %)	-	700	-
6.1(Manganese %)	-	700	-
6.1(Phosphorus %)	-	700	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1( Nb)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Cr)	-	500	-
6.1(Mo)	-	500	-
6.1(Ni)	-	500	-
6.1( Nitrogen%)	-	2000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	200	-
6.1( Copper %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1( Nb)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1(Cr)	-	500	-
6.1(Mo)	-	500	-
6.1(Ni)	-	500	-
6.1(Nitrogen%)	-	2000	-
11(Thickness)	-	100	-
11(Width)	-	100	-
10.1 (a)(Macro-examination)	-	100	-
10.1 (b)(Sulphur print)	-	500	-
Clause 6.1(IS 2830 : 2012)	-	200	-
Cl. 10.1 (b)(Sulphur Print)	-	200	-
Cl. 11.2(Out of Squareness)	-	100	-
Cl. 10.3(Camber)	-	500	-
Cl. 10.2(Bend)	-	500	-
Cl. 10.1 (a)(Macro Examination)	-	200	-
Clause 10.3(Camber)	-	500	-
Clause 10.2(Bend)	-	500	-
Cl 11(Length, Width & Thickness)	-	200	-
Cl 10.3(Workmanship)	-	200	-
Cl 10.2(Press)	-	200	-
Cl 10.2(Workmanship)	-	100	-
Cl 10.1(Workmanship)	-	100	-
Cl 9(Workmanship)	-	100	-
Cl 9(Workmanship)	-	100	-
Cl 10.1(Workmanship)	-	100	-
Cl 10.2(Workmanship)	-	100	-
Cl 10.2(Press)	-	200	-
Cl 10.3(Workmanship)	-	100	-
Cl 11(Length, Width & Thickness)	-	200	-
Clause 6, Table 1 Note : 1(By Calculation)	-	100	-
Clause 6, Table 1 Note : 3(By Calculation)	-	100	-
6(Carbon as C - IS:228)	-	500	-
6(Manganese as Mn-IS:228)	-	500	-
6(Sulphur as S- IS:228)	-	500	-
6(carbon equivalent (CE))	-	500	-
6(Micro alloying elements)	-	200	-
6(Sulphur + Phosphorus)	-	200	-
6(Copper as Cu)	-	500	-
10 (a)(Macro Examination-IS:11371)	-	200	-
10 (b)(Sulphur Print Test - IS:12037)	-	200	-
8(Selection of Test samples)	-	100	-
12(Tolerance - IS 2830)	-	200	-
13(Marking)	-	200	-
Clause 6, Table 1 Note : 1(Carbon Equivalent)	-	200	-
Clause 6, Table 1 Note : 3(Nb+V+Ti)	-	200	-
Clause 6, Table 1 Note : 9(S+P)	-	200	-
Clause 9(Freedom from Defect)	-	200	-
4(Supply of material)	-	100	-
5(Manufacture)	-	100	-
6.1(Chemical method)	-	500	-
6.2(Copper bearing quality)	-	100	-
6.3(Check Analysis)	-	100	-
10.1(Test)	-	100	-
10.2(Bend)	-	500	-
10.3(Chamber)	-	500	-
11(Dimensions)	-	100	-
12(Tolrences)	-	100	-
13(Marking)	-	100	-
Cl 6.1(Carbon)	-	500	-
Cl 6.1(Sulphur)	-	500	-
Cl 6.1(Phosphorous)	-	500	-
Cl 6.1(Manganese)	-	500	-
Cl 6.1(Silicon)	-	500	-
Cl 6.1(Nitrogen)	-	2000	-
Cl 6.1(Carbon Equivalent)	-	100	-
Cl 6.1(Aluminium)	-	500	-
Cl 6.1(Nb)	-	500	-
Cl 6.1(V)	-	500	-
Cl 6.1(Ti)	-	100	-
Cl 6.1(Nb+V+Ti)	-	100	-
Cl 6.1(Sulphur+ Phosphorous)	-	100	-
Cl 6.1(Copper)	-	100	-

Complete

07 Sep, 2025

-
Incuded w.e.f. 29.11.2024

IS 15380 (2023)

MOULDED HIGH DENSITY FIBRE HDF PANELLED DOOR SHUTTERS - SPECIFICATION ( First Revision )

ALL SIZE GRADE TYPES

31000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Sized)	-	500	-
Cl-6.1.2(Moisture content in timbers)	-	1000	-
Cl-6.2 S.No (1), i(Density, kg/m3 , Min)	-	1000	-
Cl-6.2 S.No (1), ii(Moisture content, percent, Max)	-	2000	-
Cl-6.2 S.No (1), iii(Water absorption, percent, Max)	-	1500	-
Cl-6.2 S.No (1), iv(Swelling in water, percent, Max)	-	1500	-
Cl-6.2 S.No (1), v(Modulus of rupture, N/mm2 , Min)	-	1500	-
Cl-6.2 S.No (1), vi(Internal bond strength, N/mm2 , Min)	-	1000	-
Cl-6.2 S.No (1), vii(Immersion in boiling water at (100 ± 3) °C for 4 h)	-	1000	-
Cl- 6.3(Particle Boards as Core)	-	7000	-
Cl- 6.4(Adhesive)	-	9000	-
Cl- 6.5(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	2000	-
Cl-11.1(Dimensions and Squareness Test)	-	500	-
Cl-11.2(General Flatness Test)	-	1000	-
Cl-11.3(Local Planeness Test)	-	1000	-
Cl-11.4(Impact Indentation Test)	-	1000	-
Cl-11.5(Flexure Test)	-	1000	-
Cl-11.6(Edge Loading Test)	-	1000	-
Cl-11.7(Shock Resistance Test)	-	1000	-
Cl-11.8(Buckling Resistance Test)	-	1000	-
Cl-11.9(Slamming Test)	-	1000	-
Cl-11.10(Misuse Test)	-	1000	-
Cl-11.11(Varying Humidity Test)	-	1000	-
Cl-11.12(End Immersion Test)	-	1000	-
Cl-11.13(Glue Adhesion Test)	-	1000	-
Cl-11.14(Screw Withdrawal Resistance Test)	-	1000	-
Cl-12.2(Sample Size)	-	500	-
Cl-14(Marking)	-	200	-
Cl-6.1.1(Bulk density of timber)	-	500	-
Cl-9(Workmanship and finish)	-	200	-

Complete

07 Sep, 2025

-
Included w.e.f. 06.11.2024 Exclusion: Cl-6.2 S.No (1), viii (Formaldehyde emission, mg/100 g, Max)

IS 3074 (2013)

Steel tubes for automotive purposes - Specification (Third Revision)

CDS/ERW/HFIW/CEW /Size upto and including 114.3 mm

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Workmanship)	-	200	-
6(STRAIGHTNESS)	-	500	-
7, 20,Table 1,2,4 &6( C)	-	700	-
7, Table 1,2,4 &6(Mn)	-	700	-
7, Table 1,2,4 &6(S)	-	700	-
7, Table 1,2,4 &6(P)	-	700	-
7, Table 1,2,4 &6(Si)	-	700	-
7, Table 1,2,4 &6(Ni)	-	3000	-
7, Table 1,2,4 &6(Cr)	-	500	-
7, Table 1,2,4 &6(Mo)	-	500	-
7, Table 1,2,4 &6(Mo)	-	500	-
8.2,15,17,22, Table 3,5 &7(Tensile Tests,IS 1608 Part 1)	-	1500	-
8.3,18,(Flattening Test)	-	500	-
8.4(Crushing Test)	-	500	-
8.5(Drift Test)	-	500	-
5.1(Workmanship)	-	100	-
6(STRAIGHTNESS)	-	200	-
7, 20,Table 1,2,4 &6( C)	-	700	-
7, Table 1,2,4 &6(Mn)	-	700	-
7, Table 1,2,4 &6(S)	-	700	-
7, Table 1,2,4 &6(P)	-	700	-
7, Table 1,2,4 &6(Si)	-	700	-
7, Table 1,2,4 &6(Ni)	-	2000	-
7, Table 1,2,4 &6(Cr)	-	500	-
7, Table 1,2,4 &6(Mo)	-	500	-
8.2,15,17,22, Table 3,5 &7(Tensile Tests,IS 1608 Part 1)	-	1500	-
8.3,18,(Flattening Test)	-	500	-
8.4(Crushing Test)	-	500	-
8.5(Drift Test)	-	200	-
10(Surface protection)	-	100	-
21(Condition)	-	200	-
3.2.1(Height of internal fin)	-	200	-
7, Table 1,2,4 &6(Micro Alloying element (Nb, V, Ti, B))	-	5000	-
Cl-9(Dimensions & Tolerances)	-	200	-
Cl-23.1(Leak Tightness Test- the purchaser each tube)	-	500	-
Cl-28(Leak Tightness Test)	-	500	-
Cl-23.2(Leak Tightness Test- hydraulic test pressure)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f. 30.10.2024

IS 5504 (1997)

Specification for spiral welded pipes (First Revision)

up to 600 mm

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1(MANUFACTURE)	-	100	-
4/4.2(MANUFACTURE)	-	100	-
4/4.3(MANUFACTURE)	-	100	-
Cl. 5.1(Carbon)	-	800	-
Cl. 5.1(Sulphur)	-	800	-
Cl. 5.1(Phosphorus)	-	800	-
5.2(Product Analysis)	-	500	-
6.1(Tensile Test)	-	2000	-
6.2(Flattening Test)	-	1000	-
6.3/6.3.1.1(Submerged Arc Weld Test- Guided bend test)	-	500	-
7(Hydrostatic Test- Pressure)	-	3000	-
8.1(Length)	-	500	-
8.2(Dimensions)	-	500	-
9/9.1(Finish)	-	100	-
10(Repair by Welding)	-	500	-
11(Protective coating)	-	500	-
6.1(IS 1608 Part 1)	-	1000	-
6.1(IS 1608 Part 1)	-	1000	-
8.2(IS 5504)	-	500	-
8.2(IS 5504)	-	500	-
8.2.3(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.2(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.3(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.4(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.5(IS 5504)	-	500	-
6.1(IS 1608 Part 1)	-	500	-
6.1(IS 1608 Part 1)	-	500	-
8.2(IS 5504)	-	500	-
8.2(IS 5504)	-	500	-
8.2.3(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.2(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.3(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.4(IS 5504)	-	500	-
Clause 4.2 & Annexure A, A2.5(IS 5504)	-	500	-
6.1(Yield Stress)	-	500	-
6.1(Elongation)	-	500	-
8.2(Thickness)	-	500	-
8.2(Diameter)	-	500	-
8.2.3(Ovality)	-	500	-
Clause 4.2 & Annexure A, A2.2(Transverse Tensile Strength)	-	500	-
Clause 4.2 & Annexure A, A2.3(Logitudinal Tensile-Elongation Test)	-	500	-
Clause 4.2 & Annexure A, A2.4(Transverse Guided Bend Test)	-	500	-
Clause 4.2 & Annexure A, A2.5(Nick Break Test)	-	500	-
6.1(Yield Stress)	-	500	-
6.1(Elongation)	-	500	-
8.2(Thickness)	-	200	-
8.2.3(Diameter)	-	200	-
8.2.3(Ovality)	-	200	-
Clause 4.2 & Annexure A, A2.2(Transverse Tensile Strength)	-	500	-
Clause 4.2 & Annexure A, A2.3(Logitudinal Tensile-Elongation Test)	-	500	-
Clause 4.2 & Annexure A, A2.4(Transverse Guided Bend Test)	-	500	-
Clause 4.2 & Annexure A, A2.5(Nick Break Test)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f. 30.10.2024

IS 14845 (2000)

Resilient seated cast iron air relief valves for water works purposes - specification

ALL TYPES / ALL SIZES

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 3)&(Cl5)(Type & Nom Size)	-	200	-
(Cl 3)&(Cl5)(Type & Nom Size)	-	200	-
(Cl 3)&(Cl5)(Type & Nom Size)	-	300	-
(Cl 4)(Nom.Pressures)	-	200	-
(Cl 8)(End Connection)	-	200	-
(Cl 8)(End Connection)	-	200	-
(Cl 8)(End Connection)	-	200	-
(Cl 9)(Material)	-	200	-
(Cl10.1)( Design And Manufacture)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.2)( Body)	-	200	-
(Cl10.3)( Covers of Large Orifice Chamber)	-	300	-
(Cl10.4)(High Pressure Orifice)	-	300	-
(Cl10.4)(High Pressure Orifice)	-	500	-
(Cl10.4)(High Pressure Orifice)	-	500	-
(Cl10.4)(High Pressure Orifice)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.5, Table 3)(Float)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl10.6)(Low Pressure Seat Ring)	-	500	-
(Cl 10.7)(Joint Supporting Ring)	-	500	-
(Cl 10.8)(Cowl)	-	200	-
(Cl 10.8)(Cowl)	-	200	-
(Cl 10.9)(Gasket or jointing material )	-	100	-
(Cl10.6)(Nut & Bolts)	-	100	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
Cl 10.11(Built- in-isolating Valve)	-	500	-
(Cl.11)(Finish)	-	200	-
(Cl.12)(Testing and Performance)	-	500	-
(Cl.12)(Testing and Performance)	-	500	-
(Cl.12)(Testing and Performance)	-	500	-
(Cl.12.4.4) : (Body Test )	-	2000	-
(Cl.14)(Coating)	-	500	-
(Cl.14)(Coating)	-	500	-

Complete

07 Sep, 2025

-
Included w.e.f 24.10.2024

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

Designation -19000 to 65032 all

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	500	-
7.0(Dimension and Tolerances)	-	500	-
8.1 Table-1(Al)	-	1500	-
8.1 Table-1(Cu)	-	900	-
8.1 Table-1(Mg)	-	900	-
8.1 Table-1(Si)	-	900	-
8.1 Table-1(Fe)	-	900	-
8.1 Table-1(Mn)	-	900	-
8.1 Table-1(Zn)	-	900	-
8.1 Table-1(Ti)	-	900	-
8.1 Table-1(Cr)	-	900	-
9.1(Tensile Strength)	-	1000	-
9.3(Wrapping Test)	-	500	-
10(Selection of Test Samples)	-	400	-

Complete

07 Sep, 2025

-
Included w.e.f 24.10.2024

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

YST-160 TO YST 355/WT/ERW/HFIW, ALL SIZE

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Types)	-	500	-
Clause.4.0(Carbon)	-	800	-
Clause.4.0(Sulphur)	-	800	-
Clause.4.0(Sulphur)	-	800	-
Clause.4.0(Phosphorus)	-	800	-
Clause.4.0(Silicon)	-	800	-
Clause.4.0(Manganese)	-	800	-
Clause.5.0(Supply of Material)	-	1000	-
Clause.5.0(Supply of Material)	-	1000	-
Clause.6.0(Workmanship)	-	500	-
Clause.7.0(Straightness)	-	1000	-
Clause.8.0(Basis of Calculation)	-	1000	-
Clause.9.0(Length)	-	500	-
Clause.10.0(Dimensions and properties)	-	500	-
Clause.10.0(Dimensions and properties)	-	500	-
Clause.11.0(General)	-	1000	-
Clause.11.0(Outside Dimension)	-	500	-
Clause.11.0(Thickness)	-	500	-
Clause.11.0(Thickness)	-	500	-
Clause.11.0(Concavity and Convexity)	-	1000	-
Clause.11.0(Squareness of Sides)	-	1000	-
Clause.11.0(External Corner Radiius)	-	800	-
Clause.11.0(Straightness and twist)	-	1000	-
Clause.12.0(Dimension Tolerances)	-	500	-
Clause.12.0(Dimension Tolerances)	-	500	-
Clause.13.0(Surface Protection)	-	500	-
Clause.14.0(Testing)	-	500	-
Clause.15.0(Tensile test)	-	2000	-
Clause.15.0(Yield strength)	-	500	-
Clause.15.0(Elognation Percent)	-	500	-
Clause.18.0(Marking)	-	200	-
6(Workmanship)	-	500	-
10(Dimensions and Properties)	-	500	-
11(Measurement of Shape and Size)	-	1000	-
12(Dimensions and Tolerances)	-	500	-
13(Surface Protection)	-	500	-
15(Tensile Test)	-	2000	-
Clause. 3.0(Types)	-	-	-
Clause.4.0(Carbon)	-	-	-
Clause.4.0(Sulphur)	-	-	-
Clause.4.0(Sulphur)	-	-	-
Clause.4.0(Phosphorus)	-	-	-
Clause.4.0(Silicon)	-	-	-
Clause.4.0(Manganese)	-	-	-
Clause.5.0(Supply of Material)	-	-	-
Clause.5.0(Supply of Material)	-	-	-
Clause.6.0(Workmanship)	-	-	-
Clause.7.0(Straightness)	-	-	-
Clause.8.0(Basis of Calculation)	-	-	-
Clause.9.0(Length)	-	-	-
Clause.10.0(Dimensions and properties)	-	-	-
Clause.10.0(Dimensions and properties)	-	-	-
Clause.11.0(General)	-	-	-
Clause.11.0(Outside Dimension)	-	-	-
Clause.11.0(Thickness)	-	-	-
Clause.11.0(Thickness)	-	-	-
Clause.11.0(Concavity and Convexity)	-	-	-
Clause.11.0(Squareness of Sides)	-	-	-
Clause.11.0(External Corner Radiius)	-	-	-
Clause.11.0(Straightness and twist)	-	-	-
Clause.12.0(Dimension Tolerances)	-	-	-
Clause.12.0(Dimension Tolerances)	-	-	-
Clause.13.0(Surface Protection)	-	-	-
Clause.14.0(Testing)	-	-	-
Clause.15.0(Tensile test)	-	-	-
Clause.15.0(Yield strength)	-	-	-
Clause.15.0(Elognation Percent)	-	-	-
Clause.18.0(Marking)	-	-	-
6(Workmanship)	-	-	-
10(Dimensions and Properties)	-	-	-
11(Measurement of Shape and Size)	-	-	-
12(Dimensions and Tolerances)	-	-	-
13(Surface Protection)	-	-	-
15(Tensile Test)	-	-	-

Complete

07 Sep, 2025

-
Included w.e.f 24.10.2024

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

0.125 mm TO 12.5 mm

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Tensile Test On UTM)	-	800	NIL
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	NIL
Cl 11(Workmanship)	-	100	NIL
Cl 13(Workmanship)	-	100	..
6 AND AS PER IS 7887(MICRO ALLOY)	-	500	...
6 AND AS PER IS 7887(ALUMINIUM)	-	800	...
6 AND AS PER IS 7887(PHOSPHORUS)	-	500	...
6 AND AS PER IS 7887(SULPHUR)	-	500	...
6 AND AS PER IS 7887(MANGANESE)	-	500	...
6 AND AS PER IS 7887(SILICON)	-	500	...
6 AND AS PER IS 7887(CARBON)	-	500	...
7 & 8(Ovality)	-	200	...
7 & 8(Diameter)	-	100	...
9.2(Wrapping Test)	-	200	...
9.3(Bend test)	-	200	...
10(Finish)	-	100	...
11(Coating test)	-	200	...
13(Freedom from defects)	-	100	...
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	100	...
Clause 6 and Note 3 of IS 7887(Copper)	-	500	...

Complete

07 Sep, 2025

-
-

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

TYPE-A,TYPE-B

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type A/Type B)	-	50	......
5 Table-1(Sizes Diameter of Line wire)	-	50	.....
5 Table-1(Sizes Diamater of Point wire)	-	50	.....
5 Table-1(Sizes Mass of Completed barbed wire)	-	50	.......
5 Table-1(Sizes Distance between two barbs)	-	50	......
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	50	.....
7.1(Manufacture)	-	50	.....
7.2(Manufacture)	-	100	....
7.2(Manufacture)	-	50	.....
7.3(Manufacture)	-	50	....
8(CHROMATING)	-	50	.....
9.1(Freedom from defects)	-	50	.....
9.2(Freedom from defects)	-	50	.....
12.1(Tensile Strength)	-	800	....
12.1(Breaking load)	-	100	.....
12.2.1(Mass of zinc coating (line wire))	-	200	....
12.2.2(Mass of zinc coating (point wire))	-	300	.....
12.2(Uniformity of zinc coating)	-	400	.....
12.3(Ductility)	-	100	....
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	...
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	...
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	...
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	...
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	...
Cl. 7.2(Cut Angle)	-	50	...
Cl. 7.2(Length of Barbs)	-	50	...
Cl. 7.2(Finishing of Barbs)	-	50	....
Cl. 7.1(General)	-	50	...

Complete

07 Sep, 2025

-
-

IS 210 (2009)

Grey iron castings - Specification (First Revision)

FG150,FG200,FG220,FG260,FG300,FG350,FG400

4050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	...
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	1500	...
16, Table 3(Hardness Test)	-	300	...
7.1(WORKMANSHIP AND FINISH)	-	50	...
10.1(FREEDOM FROM DEFECTS)	-	50	...
10.2(FREEDOM FROM DEFECTS)	-	100	...
13(SIZE OF TEST BARS-Diameter)	-	50	....
17,Annex B(TRANSVERSE TEST)	-	100	....
13(SIZE OF TEST BARS-Length)	-	50	...
18(HYDROSTATIC TEST)	-	1000	....

Complete

07 Sep, 2025

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

GRADE-1,GRADE-2

3100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	100	....
Cl 6.2(Diameter & Ovality)	-	50	.....
Cl 8.2(Bend test)	-	100	...
Cl 9.3(Press)	-	50	.....
Cl 6.2(Weight)	-	50	....
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1000	...
Cl 8(Physical Requirements)	-	500	...
Clause -4, 4.3(TITANIUM)	-	500	...
Clause -4, 4.2(VANADIUM)	-	500	...
Clause -4, 4.1(NIOBIUM)	-	500	...
Clause -4, 4.1(Molybdenum)	-	500	...
Clause -4, 4.1(Chromium)	-	500	...
Clause -4, 4.1(Nickel)	-	500	...
Clause -4, 4.1( ALUMINIUM)	-	500	...
Clause -4, 4.1(SILICON)	-	500	...
Clause -4, 4.1(NITROGEN)	-	4000	..
Clause -4, 4.1(MANGANESE)	-	500	...
Clause -4, 4.1(PHOSPHURS)	-	500	...
Clause -4, 4.1(SULPHUR)	-	500	...
Clause -4, 4.1( CARBON)	-	500	...
Cl. 8.1 Table 1(Elongation)	-	200	...
Cl. 8.1 Table 1(Yield Stress)	-	300	...
Clause 9.3(Bend test)	-	200	...
Clause 6.1(Size)	-	100	...
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	100	...
Clause 6.2(Mass)	-	100	...
Clause 5.1(Freedom from Defect)	-	100	...

Complete

07 Sep, 2025

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

2.65 TO 10 MM

4300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	500	....
Cl 5 & 6(Diameter)	-	200	...
Cl 7(UTM)	-	1000	...
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	200	...
Clause 3.1.1(Sulphur)	-	500	...
Clause 3.1.1(Phosphorus)	-	500	....
Cl. 7.1(Elongation)	-	300	..
Cl. 7.1(Proof Stress 0.2 %)	-	200	...
Cl. 6.2(Length)	-	100	...
Clause 7.1(Ultimate Tensile Stress)	-	500	...
Clause 8.3(Reverse Bend test)	-	100	...

Complete

07 Sep, 2025

-
-

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

I,2,3,4,4M,5,6,6M,7,7M,8,8M,9,10,10M

6800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Nominal Diameter & Out Of Shape)	-	800	....
Cl 8(Workmanship)	-	500	....
6.1(Carbon %)	-	900	...
6.1(Manganese %)	-	900	...
6.1(Phosphorus %)	-	900	.....
6.1(Sulphur %)	-	900	....
6.1(Silicon %)	-	900	....
6.1( Aluminium %)	-	1000	....

Complete

07 Sep, 2025

-
-

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

ANNEALED/SOFTENED/HARDENED&TEMPERED/COLD FINISH

8500 View breakup
-

Complete

07 Sep, 2025

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Unique Test House

VILLAGE:-SARSINI, PO:-LALRU, Tehsil Derabassi, MOHALI, S.A.S Nagar, Punjab, 140501

9896169971 -

Scope List