BIS - LIMS (Laboratory Information Management System)

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

Plot No-248 , Ecotech - III, Udyog Kendra - II, GREATER NOIDA, Gautam Buddha Nagar, Uttar Pradesh, 201306

9999669383 itlnoida.labs@gmail.com

Scope List

Reset

92 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 444 (2025)

Rubber Hoses, Textile-Reinforced, for General-Purpose Water Applications - Specification (Sixth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Material and Construction)	-	500	-
Cl-6.1(Internal diameters and tolerances)	-	1000	-
Cl-6.2(Concentricity)	-	1000	-
Cl-6.3(Tolerance of length)	-	1000	-
Cl-6.4(Minimum thickness of lining and cover)	-	1000	-
Cl-7.1, Table-2 (i)(Minimum tensile strength)	-	2000	-
Cl-7.1, Table-2 (ii)(Minimum elongation at break)	-	2000	-
Cl-7.1, Table-2 (iii)("Resistance to ageing: Change in tensile strength from original value (max) . Change in elongation at break from original value (max)")	-	2000	-
Cl-7.2, Table-3 (i)(Proof pressure at 23 0 C)	-	2000	-
Cl-7.2, Table-3 (ii)(Change in length at proof pressure)	-	2000	-
Cl-7.2, Table-3 (iii)(Minimum burst pressure)	-	3000	-
Cl-7.2, Table-3 (iv)(Adhesion between component)	-	1500	-
Cl-7.2, Table-3 (v)(Ozone resistance)	-	5000	-
Cl-7.2, Table-3 (vi)(Flexibility at 23ºC)	-	2500	-
Cl-7.2, Table-3 (vii)(Low-temperature flexibility)	-	2500	-
Cl-8(Marking)	-	100	-

15 Aug, 2028

-
Included w.e.f.22.07.2025

IS 21 (2025)

Wrought Aluminium and Aluminium Alloys for Manufacture of Utensils - Specification (Fifth Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	5000	-
Cl-5.1(Material)	-	5000	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	5000	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	2000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	1000	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	1000	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	1000	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	3000	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	1000	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	1000	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	1000	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	1000	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	1000	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	1000	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	1000	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	1000	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	1000	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	1000	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	1000	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	3000	-
Cl 5.4(Lead)	-	1000	-
Cl 5.4(Cadmium)	-	1000	-
Cl 5.4(Arsenic)	-	1000	-
Cl-7(Dimension)	-	2000	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	2000	-

15 Aug, 2028

-
Included w.e.f.22.07.2025

IS 17953 (2023)

uPVC Profiles for Windows And Doors Specification

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5.1.1(UV Resistant Virgin Material)	-	2500	-
Cl. No.5.1.2(Non-UV Resistant Virgin Material)	-	2500	-
Cl. No.5.1.3, a), Table no. 1(i)(Monoextrusion or coextrusion of a layer of any visible surface)	-	800	-
Cl. No.5.1.3, a), Table no. 1(ii)("Non-visible surface and material covered by coextrusion")	-	800	-
Cl.No.5.2(Appearance of uPVC Profile)	-	1500	-
Cl.No.5.3.1and3.2.5, Table no. 2(i)(Depth (D))	-	1000	-
Cl.No.5.3.1and3.2.5, Table no. 2(ii)(Width (W))	-	1000	-
Cl.No.5.3.1and3.2.5, Table no. 2(iii)("Sight visible surface wall thickness, Max ")	-	1000	-
Cl.No.5.3.1and3.2.5, Table no. 2(iv)("Sight visible surface flatness, Max ")	-	1000	-
Cl.No.5.3.1and3.2.5, Table no. 2(v)(Parallelism, Max)	-	1000	-
Cl.No.5.3.2(Wall Thickness of Main Profiles)	-	1000	-
Cl.No.5.3.3(Tolerances on other Dimensions)	-	1000	-
Cl.No.5.3.4(Straightness)	-	1000	-
Cl.No.5.4(Mass of Profile)	-	2000	-
Cl.No.5.5("Heat Reversion ")	-	80000	-
Cl.No.5.6(Resistance to Impact of Falling Mass)	-	8000	-
Cl.No.5.7(Heat Ageing)	-	10000	-
Cl.No.5.8.1(Tensile Bending Test)	-	10000	-
Cl.No.5.8.2(Compression Bending Test)	-	10000	-
Cl.No.5.9.(Charpy Impact Resistance of Main Profile)	-	10000	-
Cl.No.5.10.(Resistance to Weathering)	-	800000	Complete Test Rs. 50000/-(Exclusive of Resistance to weathering test) Rs. 800000/- for Resistance to Weathering test.
Cl.No.5.11(Density)	-	2000	-
Cl.No.8(Marking)	-	100	-

15 Aug, 2028

-
Included w.e.f.22.07.2025

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 , Table 1(CLASSIFICATION)	-	100	-
5.1(Colour and Pattern)	-	1000	-
5.2(Surface Finish)	-	100	-
5.2.2(Reverse side/Bonding)	-	100	-
5.3 ,Table 5(Thickness)	-	100	-
5.4(Appearance )	-	500	-
5.2.2(Sports, dirt and similar surface defects)	-	500	-
5.2.2(Fibres,hairs,scratches)	-	200	-
5.2.2(Accumulated(Combination)of surface defects)	-	200	-
5.2.2(Edge Defects)	-	200	-
5.2.2(Broken Corners )	-	200	-
5.4.4(Sanding Defects)	-	200	-
5.4.5 table 6(W arping (Flatness ))	-	100	-
5.4.6 (Length and width of a full size Laminate)	-	100	-
5.4.7,Fig. 2(Staightness of Edges)	-	100	-
5.4.8, Fig.3(Squareness of the Laminates)	-	100	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	500	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	500	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	500	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	500	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	500	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	500	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	200	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	500	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	300	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	500	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	300	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	300	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	300	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	500	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	300	-
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	300	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	500	-
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	300	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	300	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	500	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	300	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	500	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	500	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	300	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	500	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	300	-
7.2 a)(Marking)	-	100	-
7.2 b)(Marking)	-	100	-
7.2 c)(Marking)	-	100	-
7.2 d)(Marking)	-	100	-
7.2.1(Marking)	-	100	-
5 & 5.1(Colour & Pattern)	-	100	-
5.2(Surface & Finish)	-	100	-
5.2.2(Reverse side Bonding)	-	100	-
5.3(Nominal thickness)	-	100	-
5.4.1.1(Surface defects)	-	100	-
5.4.1.2(Fiber hair scratches)	-	100	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	100	-
5.4.2(Edge defect)	-	100	-
5.4.3(Broken corner)	-	100	-
5.4.4(Sanding defect)	-	100	-
5.4.5(Warping(Flatness))	-	100	-
5.4.6(Length)	-	100	-
5.4.6(Width)	-	100	-
5.4.7(Straightness of edge)	-	100	-
5.4.8(Squreness of laminate)	-	100	-
5.5Table-7(1(Surfacewear)	-	100	-
Table-7(2(Immesion in boiling water)	-	100	-
Table-7(3(Dry heat resistance)	-	600	-
Table-7(4(Dimensional stability)	-	200	-
Table-7(6(Impact by small dia.Ball)	-	700	-
Table-7(7(Impact by large dia.Ball)	-	700	-
Table-7(8(Cracking resistance)	-	500	-
Table-7(9(Scracting resistance)	-	300	-
Table-7(10(Staining resistance)	-	300	-
Table-7(10(Colour change(Xenon arc resis))	-	600	-
Table-7(11(Cigarette burn resistance)	-	200	-
Table-7(12(Formability)	-	300	-
Table-7(13(Blistering)	-	500	-
Table-7(14(Steam resistance)	-	300	-
Table-7(15(Crazing reistance)	-	300	-
Table-7(16(Moisture reistance)	-	500	-
Table-8(17(Flexural Modulus)	-	500	-
Table-8(18(Flexural strength)	-	300	-
Table-8(19(Tensile strength)	-	100	-
5.4.6 (Length and width of a full size Laminate)	-	100	-
4 , Table 1(CLASSIFICATION)	-	0	-
5.1(Colour and Pattern)	-	0	-
5.2(Surface Finish)	-	0	-
5.2.2(Reverse side/Bonding)	-	0	-
5.3 ,Table 5(Thickness)	-	0	-
5.4(Appearance )	-	0	-
5.2.2(Sports, dirt and similar surface defects)	-	0	-
5.2.2(Fibres,hairs,scratches)	-	0	-
5.2.2(Accumulated(Combination)of surface defects)	-	0	-
5.2.2(Edge Defects)	-	0	-
5.2.2(Broken Corners )	-	0	-
5.4.4(Sanding Defects)	-	0	-
5.4.5 table 6(W arping (Flatness ))	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.7,Fig. 2(Staightness of Edges)	-	0	-
5.4.8, Fig.3(Squareness of the Laminates)	-	0	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	0	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	0	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	0	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	0	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	0	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	0	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	0	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	0	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	0	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	0	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	0	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	0	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	0	-
7.2 a)(Marking)	-	0	-
7.2 b)(Marking)	-	0	-
7.2 c)(Marking)	-	0	-
7.2 d)(Marking)	-	0	-
7.2.1(Marking)	-	0	-
5 & 5.1(Colour & Pattern)	-	0	-
5.2(Surface & Finish)	-	0	-
5.2.2(Reverse side Bonding)	-	0	-
5.3(Nominal thickness)	-	0	-
5.4.1.1(Surface defects)	-	0	-
5.4.1.2(Fiber hair scratches)	-	0	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	0	-
5.4.2(Edge defect)	-	0	-
5.4.3(Broken corner)	-	0	-
5.4.4(Sanding defect)	-	0	-
5.4.5(Warping(Flatness))	-	0	-
5.4.6(Length)	-	0	-
5.4.6(Width)	-	0	-
5.4.7(Straightness of edge)	-	0	-
5.4.8(Squreness of laminate)	-	0	-
5.5Table-7(1(Surfacewear)	-	0	-
Table-7(2(Immesion in boiling water)	-	0	-
Table-7(3(Dry heat resistance)	-	0	-
Table-7(4(Dimensional stability)	-	0	-
Table-7(6(Impact by small dia.Ball)	-	0	-
Table-7(7(Impact by large dia.Ball)	-	0	-
Table-7(8(Cracking resistance)	-	0	-
Table-7(9(Scracting resistance)	-	0	-
Table-7(10(Staining resistance)	-	0	-
Table-7(10(Colour change(Xenon arc resis))	-	0	-
Table-7(11(Cigarette burn resistance)	-	0	-
Table-7(12(Formability)	-	0	-
Table-7(13(Blistering)	-	0	-
Table-7(14(Steam resistance)	-	0	-
Table-7(15(Crazing reistance)	-	0	-
Table-7(16(Moisture reistance)	-	0	-
Table-8(17(Flexural Modulus)	-	0	-
Table-8(18(Flexural strength)	-	0	-
Table-8(19(Tensile strength)	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-

15 Aug, 2028

-
Included w.e.f 28.07.2025

IS 8931 (2021)

Copper alloy single taps, combination tap assemblies, stop valves and single lever mixers for water services Specification (second revision)

38500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classfication)	-	100	-
Cl 4(Classfication)	-	100	-
Cl 6.1(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.5(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.6(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.7(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.8(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.9(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.10(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.11(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.12(Manufacture,Workmanship & Construction)	-	2000	-
Cl 6.13(Manufacture,Workmanship & Construction)	-	2000	-
Cl 7(DIMENSIONS)	-	2000	-
Cl 7(DIMENSIONS)	-	2000	-
Cl 7(DIMENSIONS)	-	2000	-
Cl 7(DIMENSIONS)	-	2000	-
Cl 7(DIMENSIONS)	-	2000	-
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	5000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	4000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	4000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	4000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	4000	-
Cl 10(PERFORMANCE REQUIREMENTS)	-	4000	-
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	5000	-
As per Table-1(Carbon)	-	1500	-
As per Table-1(Sulphur)	-	1500	-
As per Table-1(Phosphorus)	-	1500	-
As per Table-1(Manganese)	-	1500	-
As per Table-1(Nitrogen)	-	1500	-
As per Table-1(Silicon)	-	1500	-
As per Table-1(Aluminium)	-	1500	-
As per Table-1(Chromium)	-	1500	-
As per Table-1(Vanadium)	-	1500	-
As per Table-1(Molybdenum)	-	1500	-
As per Table-1(Iron)	-	1500	-
As per Table-1(Nickel)	-	1500	-
As per Table-1(Copper)	-	1500	-
As per Table-1(Zinc)	-	1500	-
As per Table-1(Lead)	-	1500	-
As per Table-1(Boron)	-	1500	-

15 Aug, 2028

-
Included w.e.f.03.07.2025

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

1090000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	3500	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1500	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1500	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	150000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	100	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	10000	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	35000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	7000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	7000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	4500	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	35000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	35000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	35000	-
11.2.2(Spark Test)	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	10000	-
11.2.5(Surface Resistance of Sheath)	-	5000	-
11.3.1(Sheath Colour)	-	1000	-
11.3.2(Sheath Marking)	-	1000	-
Annex J(Assessment of Halogens)	-	10000	-
11.3.3(Overall Diameters and Ovality)	-	1500	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	2000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	2000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	2000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	340000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	25000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	5000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	2500	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	2000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	2000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	10000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	2100	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	40000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	5000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	5000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	2500	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	5000	-
5.2(Application to the Conductor)	-	100	-
5.3(Thickness)	-	500	-
6.2(Sheath application)	-	100	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	1000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	50000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	1500	-
Annex - B of IS 17293:2020(Compatibility test)	-	2500	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1500	-
Annex - E of IS 17293 : 2020(UV resistance)	-	50000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	35000	-
6.3(Sheath Thickness)	-	500	-
6.4(Sheath Colour)	-	1000	-
7(Overall Dimension)	-	500	-
8.1(Continuity of Marking)	-	500	-
8.2(Durability)	-	500	-
8.3(Legibility)	-	500	-
9(Core Identification)	-	500	-
12(Packing and Marking)	-	100	-
4.1(Resistance)	-	500	-
7.1.2.1, 7.2.3(Annealing)	-	500	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	1500	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	50000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
IS 191 : 2007, IS 440(Copper purity test)	-	0	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	0	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	0	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	0	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.2(Spark Test)	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	0	-
11.2.5(Surface Resistance of Sheath)	-	0	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
Annex J(Assessment of Halogens)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	0	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	0	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
5.3(Thickness)	-	0	-
6.2(Sheath application)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Annex - E of IS 17293 : 2020(UV resistance)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	0	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	0	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
IS 191 : 2007, IS 440(Copper purity test)	-	0	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	0	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	0	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	0	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.2(Spark Test)	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	0	-
11.2.5(Surface Resistance of Sheath)	-	0	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
Annex J(Assessment of Halogens)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	0	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	0	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
5.3(Thickness)	-	0	-
6.2(Sheath application)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Annex - E of IS 17293 : 2020(UV resistance)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	0	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	0	-

15 Aug, 2028

-
Included w.e.f 19.06.2025

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

110000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	500	-
4.3(Nominal Diameter)	-	1000	-
4.4(Colour)	-	500	-
5.1(Polyethylene compound)	-	10000	-
5.3(Anti-oxidant)	-	5000	-
5.4(U-V stabilizer)	-	10000	-
5.7(PE Compound Quality Evaluation)	-	10000	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	10000	-
5.6(Resistance to Weathering)	-	10000	-
6.1(Outside Diameter)	-	1000	-
6.1(Out of Roundness (Ovality))	-	1000	-
6.2(Wall Thickness)	-	1000	-
7(Finish)	-	500	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	10000	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	10000	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	10000	-
8.2(Reversion Test)	-	5000	-
8.3(Density)	-	2000	-
8.6(Thermal Stability (Oxidation Induction Time))	-	10000	-
8.7(Volatile Matter Content)	-	5000	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	10000	-
8.9(Resistance to Weathering)	-	10000	-
6.4(Length of Pipe)	-	1000	-
8.4(Melt Flow Rate (MFR))	-	2000	-
8.5(Pigment Dispersion)	-	1000	-
8.10(Slow Crack Growth Rate Test)	-	20000	-
8.11(Squeeze-off)	-	20000	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	2000	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	5000	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	10000	-
5.1, 5.7 Table 2(iv) Volatile content)	-	5000	-
5.1, 5.7 Table 2(v) Water content1))	-	5000	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	1000	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	20000	-
5.3(Anti-Oxidant)	-	5000	-
5.4(U.V. Stabilizer)	-	15000	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	15000	-
5.6(ii) Hydraulic characteristics)	-	60000	For Long Term Hydrostatic Pressure Test (10000 Hrs.) = 100000. Total testing charges inluding Long Term Hydrostatic Pressure Test (10000 Hrs.) = 210000
5.6(iii) Thermal stability (Oxidation induction time))	-	10000	-
6(Dimensions of pipes)	-	5000	-
7(Finish)	-	1000	-
8.1(Hydraulic Characteristics)	-	60000	-
8.2(Reversion test)	-	5000	-
8.3(Density)	-	4000	-
8.4(Melt Flow Rate)	-	5000	-
8.5(Pigment Dispersion)	-	4000	-
8.6(Thermal Stability (Oxidation Induction Time))	-	10000	-
8.7(Volatile Matter Content)	-	10000	-
8.9(Resistance to Weathering)	-	15000	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	10000	-
8.10(Slow Crack Growth Rate Test)	-	20000	-
8.11(Squeeze-of)	-	20000	-
10(Marking)	-	500	-

15 Aug, 2028

-
Included w.e.f.13.05.2025

IS 2191 : Part 2 (2022)

WOODEN FLUSH DOOR SHUTTERS (CELLULAR, HOLLOW AND TUBULAR CORE TYPE) - SPECIFICATION PART 2 PARTICLE BOARD, HIGH DENSITY FIBRE BOARD, MEDIUM DENSITY FIBRE BOARD AND FIBRE HARDBOARD FACE PANELS (Fourth Revision)

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Sizes and Tolerances)	-	500	-
Cl-6.1.(Timber)	-	500	-
Cl-6.2(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), medium density fibre board (MDF), high density fibre board (HDF))	-	2000	-
Cl-8.1(Locks)	-	500	-
Cl-10.1(various test)	-	12000	-
Cl-10.2(End Immersion Test)	-	2500	-
Cl-10.3(Glue Adhesion Test)	-	2500	-
Cl-13(Marking)	-	500	-
Cl-6.3.1(Particle board)	-	1500	-
Cl-6.3.2(MDF board and HDF board)	-	1500	-
Cl-6.3.5(shutters with fibre hardboard face)	-	1500	-

15 Aug, 2028

-
Included w.e.f.13.05.2025

IS 712 (1984)

Specification for building limes (Third Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4 ,Table 1(Chem reqd)	-	5000	-
cl 4, Table 2(Physical reqd)	-	5000	-
Cl. 4.1 - Table 1 - i(Calcium and Magnesium Oxides, on ignited basis - IS 6932 (part 1) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - ii(Magnesium Oxides, on ignited basis - IS 6932 (part 1) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - iii(Silica, Alumina and Ferric oxide, on ignited basis - IS 6932 (part 1) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - iv(Unhydrated Magnesium oxide, on ignited basis - IS 6932 (part 5) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - v(Insoluble Residue in dilute acid and alkali, on ignited basis - IS 6932 (part 1) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - vi(Carbondioxide on oven dried basis - IS 6932 (part 2) : 1973)	-	2000	-
Cl. 4.1 - Table 1 - vii(Free moisture content - IS 1514 : 1959)	-	2000	-
Cl. 4.1 - Table 1 - viii(Available lime as CaO (dry basis) - IS 1514 : 1959)	-	2000	-
Clauses 5.1 Table No. 2, SI No. (ix) (Popping Pitting)	-	1000	-
Clauses 5.1 Table No. 2, SI No. (viii) (Soundness- Le chatelier Expansion)	-	1000	-
Clauses 5.1 Table No. 2, SI No. (vii) (Volume yield)	-	1000	-
Clauses 5.1 Table No. 2, SI No. (vi) (Workability Bumps)	-	1000	-
Clauses 5.1 Table No. 2, SI No. (v) (Transverse strength at 28 days)	-	1000	-
Clauses 5.1 Table No. 2, SI No. (iv) b) (Compressive strength at 28 days)	-	5000	-
Clauses 5.1 Table No. 2, SI No. (iv) a) (Compressive strength at 14 days)	-	5000	-
Clauses 5.1 Table No. 2, SI No. (iii) b) (Final Setting time)	-	5000	-
Clauses 5.1 Table No. 2, SI No. (iii) a) (Initial Setting time)	-	5000	-
Clauses 5.1 Table No. 2, SI No. (ii) b) (Residue on slaking (Residue on 300 micron IS sieve))	-	1000	-
Clauses 5.1 Table No. 2, SI No. (ii) a) (Residue on slaking (Residue on 850 micron IS sieve))	-	1000	-
Clauses 5.1 Table No. 2, SI No. (i) c) (Fineness- (Residue on 212 micron IS Sieve))	-	1000	-
Clauses 5.1 Table No. 2, SI No. (i) b) (Fineness- (Residue on 300 micron IS Sieve))	-	1000	-
Clauses 5.1 Table No. 2, SI No. (i) a) (Fineness- (Residue on 2.36 mm IS Sieve))	-	1000	-

15 Aug, 2028

-
Included w.e.f.05.05.2025

IS 3812 : Part 2 (2013)

Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ) plus aluminium oxide (Al2O3 ) plus iron oxide (Fe2O3 ))	-	1000	-
5.1, 6.1, Table 1(Silicon dioxide (SiO2 ))	-	1000	-
5.1, 6.1, Table 1(Magnesium oxide (MgO)	-	1000	-
5.1, 6.1, Table 1(Total sulphur as sulphur trioxide (SO3)	-	1000	-
5.1, 6.1, Table 1(Available alkalies as equivalent sodium oxide (Na2O))	-	1000	-
5.1, 6.1, Table 1(Total chlorides)	-	1000	-
5.1, 6.1, Table 1(Loss on ignition)	-	1000	-
6.2(moisture content)	-	1000	-
7.1, Table 1(Fineness — Specific surface in m2 /kg)	-	2000	-
7.1, Table 1(Particles retained on 45 micron IS sieve (wet sieving))	-	2000	-
7.1, Table 1(Soundnes)	-	2000	-
7.2(Uniformity Requirements)	-	2000	-
8.3(Independent Testing)	-	2000	-
11.1(Supplies of pulverized fuel)	-	0	-
11.2(Tolerance Requirements for the Quantity of Pulverized Fuel Ash Packed in Bags)	-	0	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (iii) (Soundness by autoclave test - Expansion of specimen)	-	2000	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (ii) (Particles retained on 45 micron IS Sieve (we sieving))	-	2000	-
Clauses 5.1 & 7.1 Table No. 2, SI No. (i) (Fineness- Specific surface by blaine's method)	-	2000	-
Clase No.7.1, Table No.2, Sl.No.i(Fineness-Specific surface by Blaine's permeability method)	-	2000	-
Clase No.7.1, Table No.2, Sl.No.ii(Particle retained on 45 micron IS sieve (wet sieving))	-	2000	-
Clase No.7.1, Table No.2, Sl.No.iii(Soundness by autoclave tests)	-	2000	-

15 Aug, 2028

-
Included w.e.f.05.05.2025

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	2000	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	2000	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	2000	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	2000	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	1000	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1000	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	1000	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	5000	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	5000	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	1000	-
7.2(Uniformity Requirements)	-	2000	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	1000	-
5.1&7.1, table-2 (III)(Lime Reactivity)	-	1000	-
5.1, 7.1, table-2, iii(Lime reacitivity)	-	1000	-

15 Aug, 2028

-
Included w.e.f.05.05.2025

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

49000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	5000	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	5000	-
7.3( Opacity)	-	5000	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	5000	-
8.2 table-9( Pipe Ends)	-	2000	-
5 / 5.1(MATERIALS )	-	5000	-
5.3(VCM Content)	-	5000	-
5.4( K-Value)	-	5000	-
5.6 / 5.6.1( Material Classification, table -1)	-	1000	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	1000	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	5000	-
7.2( Colour)	-	2000	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	5000	-
8.1.2, table 4 to 7(Wall Thickness)	-	2000	-
8.1.3 (Length, meter)	-	2000	-
8.2 table-9(Dimensions of Integral Socket)	-	5000	-
9.3 table-12( Ring Stiffness)	-	5000	-
9.4, annexure-E( Orientation Factor)	-	5000	-
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	5000	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	5000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	5000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	5000	-
12(a)( ELASTOMERIC SEALS)	-	5000	-
12(b)( ELASTOMERIC SEALS)	-	5000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	5000	-
Cl.10, Table 10/2(Effect on Water)	-	10000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	2000	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	5000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	0	-
Cl.10, Table 10/2(Effect on Water)	-	0	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	0	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	0	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	0	-
Cl.10, Table 10/2(Effect on Water)	-	0	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	0	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	0	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	-	-
Cl.10, Table 10/2(Effect on Water)	-	-	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	-	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	-	-

15 Aug, 2028

-
Included w.e.f.05.05.2025 up to 1000 mm only

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	500	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	500	-
10(Tensile test)	-	1000	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	2000	-

15 Aug, 2028

-
Included w.e.f 12.03.2025

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

28500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	500	-
Cl 3.2(Material used for composite bottom)	-	500	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	500	-
Cl 3.4(Material used for stainless steel lid)	-	500	-
Cl 3.5(Material used for tempered glass lid)	-	500	-
Cl 3.5(Material used for stainless steel rim)	-	500	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	500	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	500	-
Cl 4.2(Thickness of the finished utensil)	-	500	-
Cl 4.3(Classification)	-	100	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	500	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	500	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	500	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	500	-
Cl 5.1(Manufacturing defect & visual appearance)	-	100	-
CL 5.2(Accessibility for cleaning)	-	100	-
Cl 5.3(Joining of handles to the utensils)	-	100	-
Cl 5.4(Requirement for handles)	-	1000	-
Cl 5.5(Welding (Finish))	-	500	-
Cl 5.6(Finish of 3-ply utensil)	-	500	-
Cl 5.7(Requirement for coating)	-	500	-
Cl 5.8(Coating thickness test)	-	500	-
Cl 5.8(Coating adhesion test)	-	500	-
Cl 5.8.1(Thermal shock test (Coating))	-	500	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	500	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	1000	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	1000	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	500	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	500	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	500	-
Cl 6.7(Nominal Capacity Test)	-	500	-
Cl 8(Marking)	-	500	-
3.1(a) Carbon)	-	1000	-
3.1(b) Silicon)	-	1000	-
3.1(c)Manganese)	-	1000	-
3.1(d) Nickel)	-	1000	-
3.1(Chromium)	-	1000	-
3.1(Sulphu)	-	1000	-
3.1(Phosphorus)	-	1000	-
Stainless Steel Utensils - Specification (THIRD REVISION)(Copper)	-	500	-
3.1(Nitrogen)	-	1000	-
3.2 a(a) Carbon)	-	1000	-
3.2 a(b) Silicon)	-	1000	-
68995(Manganese)	-	1000	-
3.2 a(d) Nickel)	-	1000	-
3.2 a(Chromium)	-	1000	-
3.2 a(Sulphur)	-	1000	-
3.2 a(g) Phosphorus)	-	1000	-
3.2 a(h) Copper)	-	1000	-
3.2 a(Nitrogen)	-	1000	-
3.2 b(a) Aluminium)	-	1000	-
3.2 b(b) Copper)	-	1000	-
3.2 b(c) Magnesium)	-	1000	-
3.2 b(d) Silicon)	-	1000	-
3.2 b(e) Iron)	-	1000	-
3.2 b(f) Manganese)	-	1000	-
3.2 b(d) Silicon)	-	1000	-
3.2 b(f) Manganese)	-	1000	-
3.2 b(g) Zinc)	-	1000	-
3.2 b(h) Titanium)	-	1000	-
3.2 b(i) Chromium)	-	1000	-
3.2 b(j) Cu+Si+Fe+Mn+Zn+mg)	-	1000	-
3.2 b(k) Lead)	-	1000	-
3.2 c(a) Carbon)	-	1000	-
3.2 c(b) Silicon)	-	1000	-
3.2 c(c) Manganese)	-	1000	-
3.2 c(d) Nickel)	-	1000	-
3.2 c(e) Chromium)	-	1000	-
3.2 c(f) Sulphur)	-	1000	-
3.2 c(g) Phosphorus)	-	1000	-
3.3(a) Inner layer)	-	500	-
3.3(b) Middlelayer)	-	500	-
3.3(c) Outerlayer)	-	500	-
3.4(a) Carbon)	-	1000	-
3.4(b) Silicon)	-	1000	-
3.4(c) Manganese)	-	1000	-
3.4(d) Nickel)	-	1000	-
3.4(e) Chromium)	-	1000	-
3.4(f) Sulphur)	-	1000	-
3.4(g) Phosphorus)	-	1000	-
3.4(h) Copper)	-	1000	-
3.4(i) Nitrogen)	-	1000	-
3.4(Thickness stainless steel lid)	-	500	-
3.5(If the utensils provided with tempered glass lid)	-	500	-
4.1(Shapes and Dimensions)	-	1000	-
4.2(Thickness of the sheet)	-	500	-
4.3(Classifications)	-	100	-
4.3(Core Thickness for 3-ply Construction (asper IS15960))	-	500	-
4.3(Thickness of protective layer (as per IS 15960))	-	500	-
4.4(Thickness of 3ply full body utensil)	-	500	-
5(Workmanship and finish)	-	500	-
5.4(Handles)	-	2000	-
4.1 of IS 13395(Construction)	-	500	-
4.2 of IS 13395(Materials)	-	2000	-
4.3 of IS 13395(Selection and Size)	-	500	-
4.4 of Is 13395(Position of Handle and Knob with Respect to Cookware)	-	500	-
4.5 of IS 13395(Attachment to Cookware)	-	500	-
5.2 of IS 13395(Bending Strength)	-	1000	-
5.3 of IS 13395(Torque Strength)	-	1000	-
5.4 of IS 13395(Impact Strength)	-	1000	-
5.5 of IS 13395(Fatigue Resistance 15 000 cycles withstand)	-	1000	-
5.6 of IS 13395(Leakage)	-	1000	-
5.7 of IS 13395(Thermal Insulation)	-	1000	-
5.8 of IS 13395(Heat Resistance)	-	1000	-
5.9 of IS 13395(Washing Resistance)	-	1000	-
5.10 of IS 13395(Burning Resistance)	-	1000	-
5.5(Material comes in contact with food)	-	500	-
6.1(Staining Test)	-	1000	-
6.2(Mechanical Shock Test)	-	1000	-
6.3(Thermal Shock Test)	-	1000	-
6.4(Dry Heat Test)	-	1000	-
6.6(Heat test)	-	1000	-
6.7.1(Nominal Capacity Test)	-	500	-
6.7.2(Internal diameter of utensil)	-	500	-
3.2 b(e) Iron)	-	1000	-
Cl 3.1(Material used for manufacturing utensils)	-	0	-
Cl 3.2(Material used for composite bottom)	-	0	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	0	-
Cl 3.4(Material used for stainless steel lid)	-	0	-
Cl 3.5(Material used for tempered glass lid)	-	0	-
Cl 3.5(Material used for stainless steel rim)	-	0	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	0	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	0	-
Cl 4.2(Thickness of the finished utensil)	-	0	-
Cl 4.3(Classification)	-	0	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	0	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	0	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	0	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	0	-
Cl 5.1(Manufacturing defect & visual appearance)	-	0	-
CL 5.2(Accessibility for cleaning)	-	0	-
Cl 5.3(Joining of handles to the utensils)	-	0	-
Cl 5.4(Requirement for handles)	-	0	-
Cl 5.5(Welding (Finish))	-	0	-
Cl 5.6(Finish of 3-ply utensil)	-	0	-
Cl 5.7(Requirement for coating)	-	0	-
Cl 5.8(Coating thickness test)	-	0	-
Cl 5.8(Coating adhesion test)	-	0	-
Cl 5.8.1(Thermal shock test (Coating))	-	0	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	0	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	0	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	0	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	0	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	0	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	0	-
Cl 6.7(Nominal Capacity Test)	-	0	-
Cl 8(Marking)	-	0	-
3.1(a) Carbon)	-	0	-
3.1(b) Silicon)	-	0	-
3.1(c)Manganese)	-	0	-
3.1(d) Nickel)	-	0	-
3.1(Chromium)	-	0	-
3.1(Sulphu)	-	0	-
3.1(Phosphorus)	-	0	-
Stainless Steel Utensils - Specification (THIRD REVISION)(Copper)	-	0	-
3.1(Nitrogen)	-	0	-
3.2 a(a) Carbon)	-	0	-
3.2 a(b) Silicon)	-	0	-
68995(Manganese)	-	0	-
3.2 a(d) Nickel)	-	0	-
3.2 a(Chromium)	-	0	-
3.2 a(Sulphur)	-	0	-
3.2 a(g) Phosphorus)	-	0	-
3.2 a(h) Copper)	-	0	-
3.2 a(Nitrogen)	-	0	-
3.2 b(a) Aluminium)	-	0	-
3.2 b(b) Copper)	-	0	-
3.2 b(c) Magnesium)	-	0	-
3.2 b(d) Silicon)	-	0	-
3.2 b(e) Iron)	-	0	-
3.2 b(f) Manganese)	-	0	-
3.2 b(d) Silicon)	-	0	-
3.2 b(f) Manganese)	-	0	-
3.2 b(g) Zinc)	-	0	-
3.2 b(h) Titanium)	-	0	-
3.2 b(i) Chromium)	-	0	-
3.2 b(j) Cu+Si+Fe+Mn+Zn+mg)	-	0	-
3.2 b(k) Lead)	-	0	-
3.2 c(a) Carbon)	-	0	-
3.2 c(b) Silicon)	-	0	-
3.2 c(c) Manganese)	-	0	-
3.2 c(d) Nickel)	-	0	-
3.2 c(e) Chromium)	-	0	-
3.2 c(f) Sulphur)	-	0	-
3.2 c(g) Phosphorus)	-	0	-
3.3(a) Inner layer)	-	0	-
3.3(b) Middlelayer)	-	0	-
3.3(c) Outerlayer)	-	0	-
3.4(a) Carbon)	-	0	-
3.4(b) Silicon)	-	0	-
3.4(c) Manganese)	-	0	-
3.4(d) Nickel)	-	0	-
3.4(e) Chromium)	-	0	-
3.4(f) Sulphur)	-	0	-
3.4(g) Phosphorus)	-	0	-
3.4(h) Copper)	-	0	-
3.4(i) Nitrogen)	-	0	-
3.4(Thickness stainless steel lid)	-	0	-
3.5(If the utensils provided with tempered glass lid)	-	0	-
4.1(Shapes and Dimensions)	-	0	-
4.2(Thickness of the sheet)	-	0	-
4.3(Classifications)	-	0	-
4.3(Core Thickness for 3-ply Construction (asper IS15960))	-	0	-
4.3(Thickness of protective layer (as per IS 15960))	-	0	-
4.4(Thickness of 3ply full body utensil)	-	0	-
5(Workmanship and finish)	-	0	-
5.4(Handles)	-	0	-
4.1 of IS 13395(Construction)	-	0	-
4.2 of IS 13395(Materials)	-	0	-
4.3 of IS 13395(Selection and Size)	-	0	-
4.4 of Is 13395(Position of Handle and Knob with Respect to Cookware)	-	0	-
4.5 of IS 13395(Attachment to Cookware)	-	0	-
5.2 of IS 13395(Bending Strength)	-	0	-
5.3 of IS 13395(Torque Strength)	-	0	-
5.4 of IS 13395(Impact Strength)	-	0	-
5.5 of IS 13395(Fatigue Resistance 15 000 cycles withstand)	-	0	-
5.6 of IS 13395(Leakage)	-	0	-
5.7 of IS 13395(Thermal Insulation)	-	0	-
5.8 of IS 13395(Heat Resistance)	-	0	-
5.9 of IS 13395(Washing Resistance)	-	0	-
5.10 of IS 13395(Burning Resistance)	-	0	-
5.5(Material comes in contact with food)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test)	-	0	-
6.3(Thermal Shock Test)	-	0	-
6.4(Dry Heat Test)	-	0	-
6.6(Heat test)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.7.2(Internal diameter of utensil)	-	0	-
3.2 b(e) Iron)	-	0	-

15 Aug, 2028

-
Included w.e.f 11.02.2025

IS 4990 (2024)

PLYWOOD FOR CONCRETE SHUTTERING WORKS SPECIFICATION (Fourth Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Timber)	-	0	-
Cl-5.2(Adhesives for Bonding of Veneers)	-	0	-
Cl-6.1(Manufacture)	-	0	-
Cl-6.2(Manufacture ( Thickness of veneers))	-	0	-
Cl-6.3(Manufacture ( Physical and mechanical properties of veneers))	-	0	-
Cl-6.4, 6.7(Manufacture (Plywood for concrete shuttering))	-	0	-
Cl-6.5(Manufacture (Scarf joints))	-	0	-
Cl-6.6(Manufacture ( Preservative treatment))	-	0	-
Cl-7.1(Dimensions -length)	-	1000	-
Cl-7.2(Thickness)	-	500	-
Cl-7.3(Squareness)	-	500	-
Cl-8.1, 8.2(Workmanship and finish)	-	500	-
Cl-10.3(Moisture Content)	-	1000	-
Cl-10.4.1(Glue Adhesion in Dry State - Glue Shear Strength)	-	1000	-
Cl-10.4.2(Glue Adhesion in Dry State - Adhesion of Plies)	-	1000	-
Cl-10.5, 10.5.1(Resistance to Water Test)	-	1000	-
Cl-10.5.1.1(Water Resistance Test-Glue shear strength)	-	1000	-
Cl-10.5.1.2(Water Resistance Test-Adhesion of plies)	-	1000	-
Cl-10.5.2(Water Resistance Test (Alternate method))	-	1000	-
Cl-10.6(Water resistance test (Concrete shuttering Plywood))	-	1000	-
Cl-10.7.1, Table-2(Mycological Test- Glue shear strengt)	-	1000	-
Cl-10.7.2(Mycological Test- Adhesion of plies)	-	1000	-
Cl-10.8(Tensile Strength)	-	1000	-
Cl-10.9, Table-3 (i)(Along (parallel to the grain direction of the face veneer))	-	1000	-
Cl-10.9, Table-3 (ii)(Across (perpendicular to the grain direction of the face veneer))	-	1000	-
Cl-10.10, Table-4 (i) a(Wet Bending Strength -Modulus of Elasticity (MOE),- Average)	-	1000	-
Cl-10.10, Table-4 (i) b(Wet Bending Strength - Modulus of Elasticity (MOE),- Minimum individual)	-	1000	-
Cl-10.11(Retention of Preservative)	-	1000	-
Cl-10.12(Formaldehyde Content Test)	-	2000	-

15 Aug, 2028

-
Included w.e.f 24.02.2025 Exclusion : Cl 10.13 Steady-State Formaldehyde Emission Test

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Timber)	-	0	-
Cl-4.2(Adhesive)	-	500	-
Cl-5.1(Veneers)	-	0	-
Cl-5.2.1(Glueing)	-	0	-
Cl -5.2.2(Thickness of Veneers)	-	500	-
Cl - 5.2.3.1(Joint in Veneers)	-	0	-
Cl - 5.2.3.2(Edge joints)	-	0	-
Cl - 5.2.3.3(End joints)	-	0	-
Cl - 5.2.3.4(Scarf joints)	-	0	-
Cl - 5.2.4(Grain Direction)	-	0	-
Cl-5.3(Treatment)	-	0	-
Cl-5.4(Moisture Content)	-	1000	-
Cl-6.1(Dimensions (length))	-	1000	-
Cl-6.2(Thickness)	-	1000	-
Cl-6.3(Squareness)	-	1000	-
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6(Workmanship and finish)	-	500	-
Cl-9.3(Moisture Content)	-	1000	-
Cl-9.4.2(Glue Adhesion in Dry State- Adhesion of Plies)	-	1000	-
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength -Average)	-	1000	-
Cl-9.5.1.1(Glue Adhesion in Water Resistance - Glue Shear Strength -Average)	-	1000	-
Cl-9.5.1.2(Water Resistance Test-Adhesion of plies)	-	1000	-
Cl-9.5.2(Water Resistance Test)	-	1000	-
Cl-9.6(Tensile Strength-Along the grain)	-	1000	-
Cl-9.7(Mycological Test -Adhesion)	-	1000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1000	-
Cl-9.9, Table-3 (i) a(Wet Bending Strength- Modulus of Elasticity (MOE)- Average)	-	1000	-
Cl-9.9, Table-3 (i) b(Wet Bending Strength- Modulus of Elasticity (MOE),-Minimum individual)	-	1000	-
Cl-9.10(Retention of Preservative)	-	1000	-
Cl-9.11(Formaldehyde Content Test)	-	2000	-
Cl-9.4.2(Adhesion of Plies)	-	1000	-
5.1.1(Defects in veneers)	-	0	-

15 Aug, 2028

-
Included w.e.f 24.02.2025 Exclusion : Cl 9.12 Steady-State Formaldehyde Emission Test

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	0	-
Cl-5.2, Table- 1 (i)(Blister)	-	0	-
Cl-5.2, Table- 1 (ii)(Checks)	-	0	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	0	-
Cl-5.2, Table- 1 (iv)(Dote)	-	0	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	0	-
Cl-5.2, Table- 1 (vi)(Joints)	-	0	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	0	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	0	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	0	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	0	-
Cl-5.2, Table- 1 (xi)(Patches)	-	0	-
Cl-5.2, Table- 1 (xii)(Splits)	-	0	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	0	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	0	-
Cl-6.1(Timber)	-	0	-
Cl-6.2(Adhesive)	-	1000	-
Cl-7.2.1(Thickness of veneers)	-	0	-
Cl-7.2.3(Grain Direction)	-	0	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	0	-
Cl-7.2.5.2(Splits)	-	0	-
Cl-7.2.5.3(Overlap)	-	0	-
Cl-8.1(Dimensions -length)	-	800	-
Cl-8.2(Thickness of the plywood boards)	-	800	-
Cl-8.3(Squareness)	-	400	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	500	-
Cl-11.3.2(Mycological Test)	-	500	-
Cl-11.4(Moisture Content)	-	500	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	500	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	500	-
Cl-9(WORKMANSHIP AND FINISH)	-	500	-
Cl-7.2.4(Scarf Joints)	-	0	-
Cl-11.6(Formaldehyde Content Test)	-	2000	-
Cl-5.1(Classification by appearance)	-	0	-
Cl-5.2, Table- 1 (i)(Blister)	-	0	-
Cl-5.2, Table- 1 (ii)(Checks)	-	0	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	0	-
Cl-5.2, Table- 1 (iv)(Dote)	-	0	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	0	-
Cl-5.2, Table- 1 (vi)(Joints)	-	0	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	0	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	0	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	0	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	0	-
Cl-5.2, Table- 1 (xi)(Patches)	-	0	-
Cl-5.2, Table- 1 (xii)(Splits)	-	0	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	0	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	0	-
Cl-6.1(Timber)	-	0	-
Cl-6.2(Adhesive)	-	0	-
Cl-7.2.1(Thickness of veneers)	-	0	-
Cl-7.2.3(Grain Direction)	-	0	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	0	-
Cl-7.2.5.2(Splits)	-	0	-
Cl-7.2.5.3(Overlap)	-	0	-
Cl-8.1(Dimensions -length)	-	0	-
Cl-8.2(Thickness of the plywood boards)	-	0	-
Cl-8.3(Squareness)	-	0	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	0	-
Cl-11.3.2(Mycological Test)	-	0	-
Cl-11.4(Moisture Content)	-	0	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	0	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	0	-
Cl-9(WORKMANSHIP AND FINISH)	-	0	-
Cl-7.2.4(Scarf Joints)	-	0	-
Cl-11.6(Formaldehyde Content Test)	-	0	-
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	0	Exclusion: Cl-11.7 (Steady-State Formaldehyde Emission Test)
Cl-5.1(Classification by appearance)	-	0	-
Cl-5.2, Table- 1 (i)(Blister)	-	0	-
Cl-5.2, Table- 1 (ii)(Checks)	-	0	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	0	-
Cl-5.2, Table- 1 (iv)(Dote)	-	0	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	0	-
Cl-5.2, Table- 1 (vi)(Joints)	-	0	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	0	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	0	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	0	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	0	-
Cl-5.2, Table- 1 (xi)(Patches)	-	0	-
Cl-5.2, Table- 1 (xii)(Splits)	-	0	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	0	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	0	-
Cl-6.1(Timber)	-	0	-
Cl-6.2(Adhesive)	-	0	-
Cl-7.2.1(Thickness of veneers)	-	0	-
Cl-7.2.3(Grain Direction)	-	0	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	0	-
Cl-7.2.5.2(Splits)	-	0	-
Cl-7.2.5.3(Overlap)	-	0	-
Cl-8.1(Dimensions -length)	-	0	-
Cl-8.2(Thickness of the plywood boards)	-	0	-
Cl-8.3(Squareness)	-	0	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	0	-
Cl-11.3.2(Mycological Test)	-	0	-
Cl-11.4(Moisture Content)	-	0	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	0	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	0	-
Cl-9(WORKMANSHIP AND FINISH)	-	0	-
Cl-7.2.4(Scarf Joints)	-	0	-
Cl-11.6(Formaldehyde Content Test)	-	0	-
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	0	-
Cl-5.1(Classification by appearance)	-	-	-
Cl-5.2, Table- 1 (i)(Blister)	-	-	-
Cl-5.2, Table- 1 (ii)(Checks)	-	-	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	-	-
Cl-5.2, Table- 1 (iv)(Dote)	-	-	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	-	-
Cl-5.2, Table- 1 (vi)(Joints)	-	-	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	-	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	-	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	-	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	-	-
Cl-5.2, Table- 1 (xi)(Patches)	-	-	-
Cl-5.2, Table- 1 (xii)(Splits)	-	-	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	-	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	-	-
Cl-6.1(Timber)	-	-	-
Cl-6.2(Adhesive)	-	-	-
Cl-7.2.1(Thickness of veneers)	-	-	-
Cl-7.2.3(Grain Direction)	-	-	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	-	-
Cl-7.2.5.2(Splits)	-	-	-
Cl-7.2.5.3(Overlap)	-	-	-
Cl-8.1(Dimensions -length)	-	-	-
Cl-8.2(Thickness of the plywood boards)	-	-	-
Cl-8.3(Squareness)	-	-	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	-	-
Cl-11.3.2(Mycological Test)	-	-	-
Cl-11.4(Moisture Content)	-	-	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	-	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	-	-
Cl-9(WORKMANSHIP AND FINISH)	-	-	-
Cl-7.2.4(Scarf Joints)	-	-	-
Cl-11.6(Formaldehyde Content Test)	-	-	-
Cl-11.7(Steady-State Formaldehyde Emission Test)	-	-	-

15 Aug, 2028

-
Included w.e.f. 25.03.2025 Exclusion: Cl-11.7 Steady-State Formaldehyde Emission Test

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

165000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1000	-
IS 191:2007 & IS 440(Copper purity test)	-	1000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	4000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	4000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	4000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	4000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	4000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	4000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	2000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	2000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	2000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	2000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	2000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	2000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	5000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	5000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	500	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	5000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	4000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	500	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	500	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	6000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	6000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	6000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	6000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	500	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	6000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	6000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
IS 191:2007 & IS 440(Copper purity test)	-	0	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	0	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	0	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	0	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	0	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	0	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	0	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	0	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	0	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	0	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	0	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	0	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	0	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	0	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	0	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
IS 191:2007 & IS 440(Copper purity test)	-	0	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	0	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	0	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	0	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	0	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	0	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	0	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	0	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	0	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	0	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	0	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	0	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	0	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	0	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	0	-

15 Aug, 2028

-
Included w.e.f 05.05.2025

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

165000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	500	-
4.1.1 b) (Material : Seperator tape )	-	500	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	500	-
4.1.1 e) (Shape of conductor )	-	500	-
4.1.1 f) (Nominal size of conductor )	-	500	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	500	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	500	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	1000	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	1000	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2000	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2000	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	2000	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	2000	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	2000	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	2000	-
4.3(Fillers)	-	1000	-
4.4(Binder Tape)	-	1000	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	1000	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	1000	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1000	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1000	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	1000	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	1000	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	1000	-
4.5.6, 13.4(Colour of Sheath)	-	1000	-
5.1(High Voltage Test (at Room Temperature))	-	1000	-
5.2(Spark Test (Routine Test))	-	1000	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	3000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	3000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	3000	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	5000	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	5000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	4000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	4000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	4000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	4000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	4000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	4000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	4000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	4000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	4000	-
6.1, Table 1(CORE IDENTIFICATION)	-	4000	-
6.2(Core Identification by Numbers)	-	500	-
6.2.1(Preferred Arrangement of Marking)	-	5000	-
6.2.2(Durability)	-	500	-
7.0(CABLE CODE)	-	500	-
9.0( IDENTIFICATION)	-	500	-
10.1(Packing )	-	500	-
10.2(marking)	-	500	-
10.2.1(Standards marking)	-	500	-
13.3, 14.3(assembly of cores )	-	500	-
6.1(General Requirements)	-	500	-
6.1.1(Colour Combination Green Yellow)	-	500	-
12.1(Conductor)	-	500	-
12.2, Table 4(insulation)	-	500	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	5000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	5000	-
4.3.1 (c)(Conductivity test (Fillers))	-	5000	-
4.3.1 (b)(pH test (Fillers))	-	5000	-
4.3.1 (a)(HCl test (Fillers))	-	5000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	5000	-
5.7 (b)(pH test (Assessment of halogen test))	-	5000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	5000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	5000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	5000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	500	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	500	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	500	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	500	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	800	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	800	-
Table 2, III a (i)(Conductor Resistance)	-	800	-
Annex A(Hot Deformation)	-	600	-
6.1, Table 1(CORE IDENTIFICATION)	-	0	-
6.1(General Requirements)	-	0	-
6.1.1(Colour Combination Green Yellow)	-	0	-
12.1(Conductor)	-	0	-
12.2, Table 4(insulation)	-	0	-
Table 4(Copper Purity test)	-	0	-
4.3.1 (e)(Fluorine content test (Fillers))	-	0	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	0	-
4.3.1 (c)(Conductivity test (Fillers))	-	0	-
4.3.1 (b)(pH test (Fillers))	-	0	-
4.3.1 (a)(HCl test (Fillers))	-	0	-
5.7 (a)(HCl test (Assessment of halogen test))	-	0	-
5.7 (b)(pH test (Assessment of halogen test))	-	0	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	0	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	0	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	0	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	0	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	0	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	0	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	0	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	0	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	0	-
Table 2, III a (i)(Conductor Resistance)	-	0	-
Annex A(Hot Deformation)	-	0	-
6.1, Table 1(CORE IDENTIFICATION)	-	-	-
6.1(General Requirements)	-	-	-
6.1.1(Colour Combination Green Yellow)	-	-	-
12.1(Conductor)	-	-	-
12.2, Table 4(insulation)	-	-	-
Table 4(Copper Purity test)	-	-	-
4.3.1 (e)(Fluorine content test (Fillers))	-	-	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	-	-
4.3.1 (c)(Conductivity test (Fillers))	-	-	-
4.3.1 (b)(pH test (Fillers))	-	-	-
4.3.1 (a)(HCl test (Fillers))	-	-	-
5.7 (a)(HCl test (Assessment of halogen test))	-	-	-
5.7 (b)(pH test (Assessment of halogen test))	-	-	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	-	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	-	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	-	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	-	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	-	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	-	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	-	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	-	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	-	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	-	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	-	-
Table 2, III a (i)(Conductor Resistance)	-	-	-
Annex A(Hot Deformation)	-	-	-

15 Aug, 2028

-
Included w.e.f 12.03.2025

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

29500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	500	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	500	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	500	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	500	-
Cl-4.1(Main body of utensil)	-	1000	-
Cl-4.1(Cast cookware)	-	1000	-
Cl-4.1(Other aluminum components and parts)	-	1000	-
Cl-4.1.1(Lids (material))	-	1000	-
Cl-4.1.1(Minimum thickness of lid)	-	500	-
Cl-4.1.2(Minimum thickness of glass)	-	500	-
Cl-4.1.2(Material of rim)	-	500	-
Cl-4.1.2(Minimum thickness of rim)	-	500	-
Cl-4.2(Material of strips)	-	1000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	1000	-
Cl-4.3(Clips of lunch box)	-	1000	-
Cl-4.3(Clips of lunch box)	-	1000	-
Cl-4.3(Rivets used in lunch box)	-	1000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	1000	-
Cl-4.5(Rivets for fixing of handles)	-	500	-
Cl-4.5(Material of cap)	-	500	-
Cl-4.6(Strips used for flame guards)	-	2500	-
Cl-4.6(stainless steel)	-	2500	-
Cl-5(Fabrication)	-	2000	-
Cl-6(Shape and Dimensions)	-	1000	-
Cl-7.1(Handles, when fitted)	-	1000	-
Cl-7.2(Handles)	-	1000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	500	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	1000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	500	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	1000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	1000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	2500	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	2500	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	2500	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	2500	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	2500	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	2500	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	250	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	1000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	1000	-
Cl-8(Workmanship and Finish)	-	250	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	500	-
Cl-8.3(Minimum nominal thickness)	-	500	-
Cl-8.3(Thickness of hard anodized)	-	250	-
Cl-8.3(Finish and appearance of hard anodized)	-	250	-
Cl-8.3(Abrasion resistance of hard anodized)	-	1000	-
Cl-8.3(Colour of hard anodized)	-	500	-
Cl-8.3(Hardness of hard anodized)	-	500	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	500	-
Cl-8.5(Non-stick unreinforced PTFE)	-	500	-
Cl-8.6(Ceramic coating)	-	500	-
Cl-8.7(The thickness test, adhesion test)	-	1000	-
Cl-8.7(Minimum thickness of coating)	-	1000	-
Cl-8.7.1(Dry heat the cookware)	-	1000	-
Cl-8.8(Requirements of PTFE)	-	1000	-
Cl-8.9(Material for induction plate)	-	500	-
Cl-8.9(Test for Induction compatible base)	-	1000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	1000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	1000	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	1000	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	500	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	500	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	500	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	500	-
Cl-9.1(Normal Capacity)	-	500	-
Cl-9.2(Normal Capacity of internal diameter)	-	500	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	0	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	0	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	0	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	0	-
Cl-4.1(Main body of utensil)	-	0	-
Cl-4.1(Cast cookware)	-	0	-
Cl-4.1(Other aluminum components and parts)	-	0	-
Cl-4.1.1(Lids (material))	-	0	-
Cl-4.1.1(Minimum thickness of lid)	-	0	-
Cl-4.1.2(Minimum thickness of glass)	-	0	-
Cl-4.1.2(Material of rim)	-	0	-
Cl-4.1.2(Minimum thickness of rim)	-	0	-
Cl-4.2(Material of strips)	-	0	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	0	-
Cl-4.3(Clips of lunch box)	-	0	-
Cl-4.3(Clips of lunch box)	-	0	-
Cl-4.3(Rivets used in lunch box)	-	0	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	0	-
Cl-4.5(Rivets for fixing of handles)	-	0	-
Cl-4.5(Material of cap)	-	0	-
Cl-4.6(Strips used for flame guards)	-	0	-
Cl-4.6(stainless steel)	-	0	-
Cl-5(Fabrication)	-	0	-
Cl-6(Shape and Dimensions)	-	0	-
Cl-7.1(Handles, when fitted)	-	0	-
Cl-7.2(Handles)	-	0	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	0	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	0	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	0	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	0	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	0	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	0	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	0	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	0	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	0	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	0	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	0	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	0	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	0	-
Cl-8(Workmanship and Finish)	-	0	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	0	-
Cl-8.3(Minimum nominal thickness)	-	0	-
Cl-8.3(Thickness of hard anodized)	-	0	-
Cl-8.3(Finish and appearance of hard anodized)	-	0	-
Cl-8.3(Abrasion resistance of hard anodized)	-	0	-
Cl-8.3(Colour of hard anodized)	-	0	-
Cl-8.3(Hardness of hard anodized)	-	0	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	0	-
Cl-8.5(Non-stick unreinforced PTFE)	-	0	-
Cl-8.6(Ceramic coating)	-	0	-
Cl-8.7(The thickness test, adhesion test)	-	0	-
Cl-8.7(Minimum thickness of coating)	-	0	-
Cl-8.7.1(Dry heat the cookware)	-	0	-
Cl-8.8(Requirements of PTFE)	-	0	-
Cl-8.9(Material for induction plate)	-	0	-
Cl-8.9(Test for Induction compatible base)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	0	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	0	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	0	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	0	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	0	-
Cl-9.1(Normal Capacity)	-	0	-
Cl-9.2(Normal Capacity of internal diameter)	-	0	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	0	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	0	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	0	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	0	-
Cl-4.1(Main body of utensil)	-	0	-
Cl-4.1(Cast cookware)	-	0	-
Cl-4.1(Other aluminum components and parts)	-	0	-
Cl-4.1.1(Lids (material))	-	0	-
Cl-4.1.1(Minimum thickness of lid)	-	0	-
Cl-4.1.2(Minimum thickness of glass)	-	0	-
Cl-4.1.2(Material of rim)	-	0	-
Cl-4.1.2(Minimum thickness of rim)	-	0	-
Cl-4.2(Material of strips)	-	0	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	0	-
Cl-4.3(Clips of lunch box)	-	0	-
Cl-4.3(Clips of lunch box)	-	0	-
Cl-4.3(Rivets used in lunch box)	-	0	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	0	-
Cl-4.5(Rivets for fixing of handles)	-	0	-
Cl-4.5(Material of cap)	-	0	-
Cl-4.6(Strips used for flame guards)	-	0	-
Cl-4.6(stainless steel)	-	0	-
Cl-5(Fabrication)	-	0	-
Cl-6(Shape and Dimensions)	-	0	-
Cl-7.1(Handles, when fitted)	-	0	-
Cl-7.2(Handles)	-	0	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	0	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	0	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	0	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	0	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	0	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	0	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	0	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	0	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	0	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	0	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	0	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	0	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	0	-
Cl-8(Workmanship and Finish)	-	0	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	0	-
Cl-8.3(Minimum nominal thickness)	-	0	-
Cl-8.3(Thickness of hard anodized)	-	0	-
Cl-8.3(Finish and appearance of hard anodized)	-	0	-
Cl-8.3(Abrasion resistance of hard anodized)	-	0	-
Cl-8.3(Colour of hard anodized)	-	0	-
Cl-8.3(Hardness of hard anodized)	-	0	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	0	-
Cl-8.5(Non-stick unreinforced PTFE)	-	0	-
Cl-8.6(Ceramic coating)	-	0	-
Cl-8.7(The thickness test, adhesion test)	-	0	-
Cl-8.7(Minimum thickness of coating)	-	0	-
Cl-8.7.1(Dry heat the cookware)	-	0	-
Cl-8.8(Requirements of PTFE)	-	0	-
Cl-8.9(Material for induction plate)	-	0	-
Cl-8.9(Test for Induction compatible base)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	0	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	0	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	0	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	0	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	0	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	0	-
Cl-9.1(Normal Capacity)	-	0	-
Cl-9.2(Normal Capacity of internal diameter)	-	0	-

15 Aug, 2028

-
Included w.e.f 11.02.2025

IS 8978 (1992)

Specification for electric instantaneous water heaters (Second Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.7 of IS 302-2-35:2017(Marking)	-	10	-
Cl.6 of IS 302-2-35:2017(Classification)	-	10	-
Cl.6 of IS 302-2-35:2017(Classification)	-	10	-
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	100	-
Cl.10 of IS 302-2- 35:2011(Power Input & Current )	-	100	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	28	-
Cl.7 of IS 302-2-35:2017(Marking)	-	29	-
Cl.11 of 302-2-35:2017(Heating)	-	30	-
Cl.11 of 302-2-35:2017(Heating)	-	100	-
Cl.11 of 302-2-35:2017(Heating)	-	100	-
Cl.11 of 302-2-35:2017(Heating)	-	100	-
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	500	-
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	500	-
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	500	-
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	500	-
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	310	-
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	500	-
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	500	-
Cl.17 IS 302-2-35:2017(Overload Protection of Transformers & Associated circuits )	-	500	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	500	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	500	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	100	-
Cl.20 of IS 302-2-35-2011(Stability & Mechanical Hazards )	-	100	-
Cl.21.1 of IS 302-2-35-2011(Mechanical strength)	-	100	-
Cl. 21.2 of IS 302-1:2008(Mechanical strength)	-	100	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	30	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	30	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	30	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	50	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	50	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	50	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	50	-
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	50	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	50	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	50	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	50	-
Cl.30 of IS 302-2-35: 2011(Resistance to Heat and Fire)	-	50	-
Cl.30 of IS 302-2-35: 2011(Resistance to Heat and Fire)	-	50	-
Cl.31 of IS 302-2-35: 2011(Resistance to Rusting )	-	50	-
Cl.32 of IS 302-2-35: 2011(Radiation, Toxicity and Similar Hazards )	-	50	-
Cl.10 of IS 8978 : 1992(Finish)	-	50	-
Cl.11 of IS 8978 : 1992(Operation of flow switch)	-	50	-
Cl.12 of IS 8978 : 1992(Endurance)	-	50	-
Cl.12 of IS 8978 : 1992(Endurance)	-	50	-
Cl.10 of IS 8978 : 1992(Finish)	-	50	-
Cl.31 of IS 302-2-35: 2017(Resistance to Rusting )	-	50	-
Cl.30.2 of IS 302-1:2008(Resistance to Heat and Fire)	-	50	-
Cl.30.1 of IS 302-1:2008(Resistance to Heat and Fire)	-	50	-
Cl.29.2 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Creepage distance )	-	50	-
Cl.29.1 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	50	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.25.5 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Type of attachment )	-	30	-
Cl.25.1 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : connection to the supply mains)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.24 of IS 302-2-35:2017(Component )	-	30	-
Cl.23 of IS 302-2-35:2017(Internal Wiring ; Colour of earthing conductor)	-	30	-
Cl.23 of IS 302-2-35:2017(Internal Wiring)	-	30	-
Cl.22.110 of IS 302-2-35:2017(Construction : Provision for fixing to wall )	-	30	-
Cl.22.109 of IS 302-2-35:2017(Construction : Operation of presure switch of open outlet water heater )	-	30	-
Cl.22.108 of IS 302-2-35:2017(Construction : Temperature of outlet water intended to supply for showring )	-	30	-
Cl.22.107 of IS 302-2-35:2017(Construction : Temperature of outlet )	-	30	-
Cl.22.106 of IS 302-2-35:2017(Construction : Operation of thermal cut out for closed water heater )	-	30	-
Cl.22.104 of IS 302-2-35:2017(Construction : Pressure in open outlet water heaters )	-	30	-
Cl.22.103 of IS 302-2-35:2017(Construction : Pressure relief device operation for closed water heater )	-	30	-
Cl.22.102 of IS 302-2-35:2017(Construction : excessive temperature of outlet )	-	30	-
Cl.22.101 of IS 302-2-35:2017(Construction : Rated pressure of closed water heater )	-	30	-
Cl.22.34, Cl 22.35 of IS 302-1:2008(Construction : Shaft of operating Knobs )	-	30	-
Cl.22.33 of IS 302-1:2008(Construction : Direct contact of liquids )	-	30	-
Cl 22.26 ,Cl.22.28, Cl 22.29, Cl 22.30 , Cl 22.31, Cl 22.32 of IS 302-1:2008(Construction : Supplymentry/ double / reinforced insulation for Class II/ Class III appliance )	-	30	-
Cl.22.18 of IS 302-1:2008(Construction : Resistance to corrosion )	-	30	-
Cl.22.17 of IS 302-1:2008(Construction : Spacers )	-	30	-
Cl.22.14 of IS 302-1:2008(Construction : Ragged or sharp edges )	-	30	-
Cl.22.12 of IS 302-1:2008(Construction : Fixing of Handle, knob, grips, levers and similar parts )	-	30	-
Cl.22.11 of IS 302-1:2008(Construction : Fixing of non detachable parts )	-	30	-
Cl.22.7 of IS 302-1:2008(Construction : safeguards against the risk of excessive pressure. )	-	30	-
Cl.22.6 of IS 302-2-35:2017(Construction : size of drain hole )	-	30	-
Cl.22.6 of IS 302-1:2008(Construction : effect of water on 3 insulation )	-	30	-
Cl.22.2 of IS 302-1:2008(Construction : connection to supply mains )	-	30	-
Cl.22.1 of IS 302-1:2008(Construction : IP test )	-	30	-
Cl. 21.2 of IS 302-1:2008(Mechanical strength : prevent penetration by sharp implements. )	-	30	-
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	30	-
Cl.20 of IS 302-2-35:2017(Stability & Mechanical Hazards )	-	30	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of insulation of supply cord)	-	50	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of test corner)	-	50	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Emission of flames, molten metal ,or poisonous or ignitable gas)	-	50	-
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	50	-
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	50	-
Cl.15 of IS 302-2-35:2017(Moisture Resistance )	-	50	-
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	50	-
Cl.13 of IS 302-2-35:2017(Leakage Current & 3 Strength at Operating Temperature : High voltage )	-	50	-
Cl.13 of IS 302-2-35:2017(Leakage Current & 3 Strength at Operating Temperature )	-	50	-
Cl.11 of 302-2-35:2017(Heating : room temperature)	-	50	-
Cl.11 of 302-2-35:2017(Heating : Insulation of supply cord)	-	50	-
Cl.11 of 302-2-35:2017(Heating : Temperature rise of test corner)	-	50	-
Cl.10 of IS 302-2- 35:2017(Power Input & Current )	-	50	-
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	50	-
Cl.7.102 of IS 302-2-35:2017(Marking : Standard mark)	-	50	-
Cl.7.101 of IS 302-2-35:2017(Marking : Woter inlet and outlet idetification)	-	30	-
Cl.7.15 of IS 302-1:2008(Marking : Position of marking)	-	30	-
Cl.7.14 of IS 302-1:2008(Marking ; Legibility and durability)	-	30	-
Cl.7.13 of IS 302-1:2008(Marking : Language)	-	30	-
Cl.7.10 & 7.11 of IS 302-1:2008(Marking : Indication for direction of control)	-	30	-
Cl.7.6 of IS 302-1:2008(Marking : Symbols)	-	30	-
Cl.7.1 of IS 302-2-35:2017(Marking : rated pressure)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Country of manufacture)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : IP number )	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Symbol for class II)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Molel or type)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Manufacture identification)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Rated power input)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Nature of supply)	-	30	-
Cl.7.1 of IS 302-1:2008(Marking : Rated Voltage)	-	30	-
4(GENERAL REQUIREMENTS)	-	30	-
5(GENERAL NOTE ON TEST)	-	30	-
Cl-19.11.4.1(Electrostatic discharge)	-	30	-
Cl-19.11.4.2(Radiated Fields)	-	30	-
Cl-19.11.4.3(Fast transient bursts)	-	30	-
Cl-19.11.4.4(Surge Immunity test)	-	30	-
Cl-19.11.4.5(Immunity to conducted discharge)	-	30	-
Cl-19.11.4.6(Voltage dips and interruptions)	-	30	-
Cl-19.11.4.7(Harmonics)	-	30	-
7(Marking)	-	30	-
7(Marking)	-	30	-
(Cl.7.1 of IS 302-2-35:2017)(Marking)	-	30	-
(Cl.7.101 of IS 302-2-35:2017)(Marking)	-	30	-
(Cl.8.1.1 of IS 8978:1992)(Marking)	-	30	-
(Cl.19.13 of IS 302-2-35:2017)(Abnormal operation)	-	30	-
(Cl.19.13 of IS 302-2-35:2017)(Abnormal operation)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.22 of IS 302-2-35:2017)(Construction)	-	30	-
(Cl.23 of IS 302-2-35:2017)(Internal wiring)	-	30	-
(Cl.23 of IS 302-2-35:2017)(Internal wiring)	-	30	-
(Cl.23 of IS 302-2-35:2017)(Internal wiring)	-	30	-
(Cl.23 of IS 302-2-35:2017)(Internal wiring)	-	30	-
(Cl.24 of IS 302-2-35:2017)(Components)	-	30	-
(Cl.24 of IS 302-2-35:2017)(Components)	-	30	-
(Cl.24 of IS 302-2-35:2017)(Components)	-	30	-
(Cl.24 of IS 302-2-35:2017)(Components)	-	30	-
(Cl.24 of IS 302-2-35:2017)(Components)	-	30	-
(Cl.25.8 of IS 302-2-35:2017)(Supply Connection and External Flexible cords)	-	30	-
(CL.27.5 of IS 302-2-35:2017)(Provision for Earthing)	-	30	-
Cl.22.44 of IS 302-1:2008(Construction : Shape and decoration )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.22 of IS 302-2-35-2011(Construction )	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	30	-
Cl.27.5 of IS 302-2-35:2017(Provision for Earthing : ECR )	-	30	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	30	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	30	-
Cl.25.18 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	30	-
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test - displacement )	-	30	-
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test )	-	30	-
Cl.25.12 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Moulding of supply cord )	-	30	-
Cl.25.10 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Colour of Earthing conductor )	-	30	-
Cl.25.8 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Resistance of supply cord )	-	30	-
Cl.7.8 of IS 302-1:2008(Marking : Terminal for connection )	-	30	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : effect on container)	-	30	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : High voltage)	-	30	-
Cl.22.47 of IS 302-2-35:2017(Construction : Water pressure test )	-	30	-

15 Aug, 2028

-
Included w.e.f 15.01.2025

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
7(Marking)	-	20	-
6(Classification )	-	25	-
6(Classification )	-	50	-
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	50	-
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	100	-
(Cl.11 of 302-2-21:2011)(Heating)	-	50	-
(Cl.11 of 302-2-21:2011)(Heating)	-	50	-
(Cl.11 of 302-2-21:2011)(Heating)	-	50	-
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	250	-
(Cl.13 of IS 302-2-21:2011)(Electrical Strength at Operating Temperature)	-	250	-
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	250	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	250	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	250	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	250	-
(Cl.17 of IS 302-2-21:2011)(Overload protection of transformers & associated circuits)	-	100	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	250	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	250	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	250	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	250	-
(Cl.20 of IS 302-2-21:2011)(Stability & Mechanical Hazards)	-	50	-
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	100	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.24ofIS302-221:2011)(Component)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	10	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	50	-
(Cl.28 of IS 302-2-21:2011)(Screws & Connections)	-	50	-
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	50	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	50	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	50	-
(Cl.31 of IS 302-2-21:2011)(Resistance to Rusting)	-	50	-
(Cl.15 of IS 2082:2018)(Verification of the Rated Capacity)	-	50	-
(Cl.16 of IS 2082:2018)(Standing Loss per 24 Hours)	-	3000	-
(Cl.17 of IS 2082:2018)(Hot Water Output)	-	1500	-
(Cl.18 of IS 2082:2018)( Reheating Time)	-	1500	-
(Cl.19 of IS 2082:2018)(Mixing Factor)	-	500	-
(Cl.20 of IS 2082:2018)(Deviation of Dial Calibration)	-	100	-
(Cl.21 of IS 2082:2018)(Cyclic Temperature Variation)	-	500	-
(Cl.22 of IS 2082:2018)(Finish)	-	50	-
Cl.22 of IS 2082:2018(Finish)	-	50	-
Cl.21 of IS 2082:2018(Cyclic Temperature Variation)	-	100	-
Cl.20 of IS 2082:2018(Deviation of Dial Calibration)	-	25	-
Cl.19 of IS 2082:2018(Mixing Factor)	-	50	-
Cl.18 of IS 2082:2018( Reheating Time)	-	100	-
Cl.17 of IS 2082:2018(Hot Water Output)	-	100	-
Cl.16 of IS 2082:2018(Standing Loss per 24 Hours)	-	100	-
Cl.15 of IS 2082:2018(Verification of the Rated Capacity)	-	50	-
Cl.31 of IS 302-2-21:2018(Resistance to Rusting)	-	100	-
Cl.30.2 of IS 302-1:2008(Resistance to Heat & Fire : Glow wire test )	-	50	-
Cl.30.1 of IS 302-1:2008(Resistance to Heat & Fire : Ball pressure test )	-	50	-
Cl.29.2 of IS 302-1:2008(Clearances, Creepage Distances and Solid Insulation : Creepage distance )	-	50	-
Cl.29.1 of IS 302-1:2008(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	50	-
Cl.28 of IS 302-2-21:2018(Screws & Connections)	-	50	-
Cl.27.5 of IS 302-1:2008(Provision for Earthing : ECR )	-	20	-
Cl.27 of IS 302-2-21:2018(Provision for Earthing)	-	20	-
Cl.26 of IS 302-2-21: 2018(Terminals for External Conductors)	-	20	-
Cl.25.18 of IS 302-1:2008(Supply Connection & External Flexible Cords)	-	20	-
Cl.25.15 of IS 302-1:2008(Supply Connection & External Flexible Cords : Cord grip test - displacement )	-	20	-
Cl.25.15 of IS 302-1:2008(Supply Connection & External Flexible Cords : Cord grip test )	-	20	-
Cl.25.12 of IS 302-1:2008(Supply Connection & External Flexible Cords : Moulding of supply cord )	-	20	-
Cl.25.10 of IS 302-1:2008(Supply Connection & External Flexible Cords : Colour of Earthing conductor )	-	20	-
Cl.25.5 of IS 302-1:2008(Supply Connection & External Flexible Cords : Type of attachment )	-	20	-
Cl.25 of IS 302-2-21:2018(Supply Connection & External Flexible Cords : connection to the supply mains)	-	20	-
Cl.24.102 of IS 302-221:2018(Component : Operation of thermal cut-out )	-	20	-
Cl.24.101 of IS302-221:2018(Component : Location of non self reseting thermal cut out )	-	20	-
Cl.24of IS 302-221:2018(Component : Relevent Indian standards )	-	20	-
Cl. 23 of IS 302-1:2008(Internal Wiring : color identification for earthing conductor )	-	20	-
Cl. 23 of IS 302-1:2008(Internal Wiring )	-	20	-
Cl.22.111 of IS 302-2-21:2018(Construction : Resistance to vacuum )	-	20	-
Cl.22.110 of IS 302-2-21:2018(Construction : meterial of connections )	-	20	-
Cl.22.110 of IS 302-2-21:2018(Construction : Material of Inner conatiner )	-	20	-
Cl.22.109 of IS 302-2-21:2018(Construction : Drain for appliance having a capacity of more than 15 liter)	-	20	-
Cl.22.108 of IS 302-2-21:2018(Construction : fixing to wall )	-	20	-
Cl.22.107 of IS 302-2-21:2018(Construction : Position of Heating elements and thermal control sensor)	-	20	-
Cl.22.106 of IS 302-2-21:2018(Construction : Operation of thermal cut- out )	-	20	-
Cl.22.104 of IS 302-2-21:2018(Construction : Outlet of open outlet heater )	-	20	-
Cl.22.103 of IS 302-2-21:2018(Construction : Operation of Pressure relieve devices )	-	20	-
Cl.22.102 of IS 302-2-21:2018(Construction : repeated drawing of water temp )	-	20	-
Cl.22.101 of IS 302-2-21:2018(Construction : rated pressure of closed water heater )	-	20	-
Cl.22.47 of IS 302-2-21:2018 (Construction : Water pressure test )	-	20	-
Cl.22.44 of IS 302-1:2008(Construction : Shape and decoration of enclosure)	-	20	-
Cl.22.34, Cl 22.35 of IS 302-1:2008(Construction : Shaft of operating Knobs )	-	20	-
Cl.22.33 of IS 302-1:2008(Construction : Direct contact of liquids )	-	20	-
Cl 22.26 ,Cl.22.28, Cl 22.29, Cl 22.30 , Cl 22.31, Cl 22.32 of IS 302-1:2008(Construction : Supplymentry/ double / reinforced insulation for Class II/ Class III appliance )	-	20	-
Cl.22.18 Of IS 302-1:2008(Construction : Resistance to corrosion )	-	20	-
Cl.22.17 of IS 302-1:2008(Construction : Spacers )	-	20	-
Cl.22.14 of IS 302-1:2008(Construction : ragged or sharp edges)	-	20	-
Cl.22.12 of IS 302-1:2008(Construction : Fixing of Handle, knob, grips, levers and similar parts)	-	20	-
Cl.22.11 of IS 302-1:2008(Construction : Fixing of non detachable part )	-	20	-
Cl.22.7 of IS 302-1:2008(Construction: adequate safeguards against the risk of excessive pressure)	-	20	-
Cl.22.6 of IS 302-2-21:2018(Construction : Size of drain hole )	-	20	-
Cl.22.6 of IS 302-1:2008(Construction : Effect of water on 3 insulation )	-	20	-
Cl.22.2 of IS 302-1:2008(Construction : Provision to ensure all pole disconnection )	-	70	-
Cl.22.1 of IS 302-1:2008(Construction : IP test )	-	70	-
Cl.21.2 of IS 302-1:2008(Mechanical strength : prevent penetration by sharp implements. )	-	70	-
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	60	-
Cl.20 of IS 302-1:2008(Stability & Mechanical Hazards)	-	220	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : leakage from container during test)	-	110	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : High Voltage )	-	110	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : Insulation of the supply cable or cord)	-	110	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : Wall ceiling temp. of test corner )	-	110	-
Cl.19 of IS 302-2-21:2018(Abnormal Operation : emission of flame or molten metal or poisonous or ignitable gas )	-	510	-
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Electric Strentgh )	-	110	-
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Leakage current )	-	110	-
Cl.15 of IS 302-2-21-2018(Moisture Resistance)	-	110	-
Cl.14 of IS 302-2-21:2018(Transient Over Voltages)	-	10	-
Cl.13 of IS 302-2-21:2018(3 Strength at Operating Temperature)	-	10	-
Cl.13 of IS 302-2-21:2018(Leakage Current )	-	260	-
Cl.11 of 302-2-21:2018(Heating : Room Temp.)	-	160	-
Cl.11 of 302-2-21:2018(Heating : Temp of Rubber or PVC insulation of internal and external wiring)	-	10	-
Cl.11 of 302-2-21:2018(Heating : Temp of Walls, ceilings and floor of the test corner )	-	10	-
Cl.10 of IS 302-2-21: 2018(Power Input & Current)	-	10	-
Cl.8 of IS 302-2-21:2018(Protection Against Access to Live Parts)	-	10	-
7.101(Marking : Indifiction of water inlet and water outlet )	-	10	-
7.14(Marking : Legibility and durability)	-	10	-
7.13(Marking : Official language of Instruction )	-	10	-
7.11(Marking : Indication of controls )	-	10	-
7.8(Marking : Terminals )	-	10	-
7.6(Marking : Symbol used )	-	10	-
7.1(Marking : Warning for Open- outlet )	-	10	-
7.1(Marking : Statement for pressure reducing valve ( For rated pressure less than 0.6 MPa))	-	10	-
7.1(Marking : Statement for a pressure-relief device)	-	10	-
7.1(Marking : Rated capacity)	-	10	-
7.1(Marking : Rated pressure)	-	10	-
7.1(Marking : Country of manufacture)	-	10	-
7.1(Marking: IP Number)	-	10	-
7.1(Marking: Symbol for Class II)	-	10	-
7.1(Marking: Model or type reference)	-	10	-
7.1(Marking: Name, trademark or identification mark of manufacturer )	-	10	-
7.1(Marking : Rated power input)	-	10	-
7.1(Marking : Symbol for nature of supply )	-	10	-
7.1(Marking : Rated Voltage )	-	10	-
Cl.32 of IS 302-1:2008()	-	10	-
4(GENERAL REQUIREMENT)	-	10	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	10	-
12(THERMOSTAT SETTING)	-	260	-
Cl-10(Mounting of the water heater)	-	10	-
Cl-11(Measurements of stored water temperature)	-	10	-
Cl-12(Thermostat setting)	-	150	-
Cl-13(Measurement of energy consumption)	-	510	-
Cl-14(Verification of the rated capacity)	-	10	-
(Cl.22 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.108 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.6 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.101 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.105 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.101 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.103 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.104 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.104 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.105 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.22.109 of IS 302-2-21:2018)(Constructions)	-	10	-
(Cl.24.101 of IS 302-2-21:2018)(Components)	-	10	-
(Cl.25 of IS 302-2-21:2018)(Supply Connection and External Flexible cords)	-	10	-
Cl.25.8 of IS 302-2-21:2018(Supply Connection & External Flexible Cords : Resistance of supply cord )	-	10	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
7(Marking)	-	-	-
6(Classification )	-	-	-
6(Classification )	-	-	-
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	-	-
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	-	-
(Cl.11 of 302-2-21:2011)(Heating)	-	-	-
(Cl.11 of 302-2-21:2011)(Heating)	-	-	-
(Cl.11 of 302-2-21:2011)(Heating)	-	-	-
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	-	-
(Cl.13 of IS 302-2-21:2011)(Electrical Strength at Operating Temperature)	-	-	-
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	-	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	-	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	-	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	-	-
(Cl.17 of IS 302-2-21:2011)(Overload protection of transformers & associated circuits)	-	-	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	-	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	-	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	-	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	-	-
(Cl.20 of IS 302-2-21:2011)(Stability & Mechanical Hazards)	-	-	-
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl.22 Of IS 302-2-21:2011)(Construction)	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl. 23 of IS 302-2-21: 2011)(Internal Wiring )	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.24ofIS302-221:2011)(Component)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	-	-
(Cl.28 of IS 302-2-21:2011)(Screws & Connections)	-	-	-
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	-	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	-	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	-	-
(Cl.31 of IS 302-2-21:2011)(Resistance to Rusting)	-	-	-
(Cl.15 of IS 2082:2018)(Verification of the Rated Capacity)	-	-	-
(Cl.16 of IS 2082:2018)(Standing Loss per 24 Hours)	-	-	-
(Cl.17 of IS 2082:2018)(Hot Water Output)	-	-	-
(Cl.18 of IS 2082:2018)( Reheating Time)	-	-	-
(Cl.19 of IS 2082:2018)(Mixing Factor)	-	-	-
(Cl.20 of IS 2082:2018)(Deviation of Dial Calibration)	-	-	-
(Cl.21 of IS 2082:2018)(Cyclic Temperature Variation)	-	-	-
(Cl.22 of IS 2082:2018)(Finish)	-	-	-
Cl.32 of IS 302-1:2008()	-	-	-
4(GENERAL REQUIREMENT)	-	-	-
5(GENERAL CONDITIONS FOR THE TESTS)	-	-	-
12(THERMOSTAT SETTING)	-	-	-
Cl-10(Mounting of the water heater)	-	-	-
Cl-11(Measurements of stored water temperature)	-	-	-
Cl-12(Thermostat setting)	-	-	-
Cl-13(Measurement of energy consumption)	-	-	-
Cl-14(Verification of the rated capacity)	-	-	-
(Cl.22 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.108 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.6 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.47 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.101 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.105 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.101 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.103 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.104 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.104 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.105 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.22.109 of IS 302-2-21:2018)(Constructions)	-	-	-
(Cl.24.101 of IS 302-2-21:2018)(Components)	-	-	-
(Cl.25 of IS 302-2-21:2018)(Supply Connection and External Flexible cords)	-	-	-

15 Aug, 2028

-
Included w.e.f 07.01.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	1000	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	500	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	1000	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	2000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	2000	-
Cl-7.2(Reversion Test)	-	1000	-
Cl-7.3(Tensile Test)	-	1000	-
Cl-7.3.1(Test Piece)	-	100	-
Cl-7.3.2(Procedure)	-	100	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	500	-
Cl-8.0(Supply of pipes)	-	100	-
Cl-9.0(Coiling)	-	500	-
Cl-10.0(Sampling and criteria for conformity)	-	100	-
Cl-11(Marking)	-	100	-
3(Class of Pipe)	-	100	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	500	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	500	-
6(Visual Appearance)	-	500	-
7.1 & Table 2(Hydraulic Characteristics)	-	2000	-
7.1 & Table 2(Hydraulic Characteristics)	-	2000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Strength)	-	1000	-
7.3(Elongation at Break)	-	1000	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	500	-
4.2(a)(Carbon Black Content-IS 2530)	-	500	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	500	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	200	-
5(Lining - IS 444)	-	200	-
5(Reinforcement - IS 444)	-	200	-
5(Cover - IS 444)	-	200	-
5(Lining and Cover - IS 444)	-	200	-
6.1- Table 1(Internal diameters - ISO 4671)	-	500	-
6.2(Concentricity - ISO 4671)	-	500	-
6.3(Length -IS 4671)	-	500	-
6.4( thickness of the lining plus cover - ISO 4671)	-	500	-
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	500	-
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	1000	-
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	1000	-
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	1000	-
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	1000	-
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	1000	-
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	1000	-
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	1000	-
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	1000	-
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	1000	-
7.2 - Table 3(Adhesion between components - ISO 8033)	-	1000	-
7.2 - Table 3(Ozone resistance - ISO 7326)	-	2000	-
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	1000	-
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	1000	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

IS 12585 (2023)

SPECIFICATION FOR THERMOPLASTIC HOSES (TEXTILE REINFORCED) FOR WATER - GENERAL PURPOSE ( First Revision of IS 12585 )

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials and Construction)	-	250	-
5(Materials and Construction)	-	250	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	250	-
6.2(Concentricity)	-	250	-
6.3(Tolerance on Length)	-	250	-
6.4(Minimum Wall Thickness)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	250	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	800	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	800	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	800	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	800	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	800	-
5(Materials and Construction)	-	0	-
5(Materials and Construction)	-	0	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	0	-
6.2(Concentricity)	-	0	-
6.3(Tolerance on Length)	-	0	-
6.4(Minimum Wall Thickness)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	0	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	0	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	0	-
5(Materials and Construction)	-	0	-
5(Materials and Construction)	-	0	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	0	-
6.2(Concentricity)	-	0	-
6.3(Tolerance on Length)	-	0	-
6.4(Minimum Wall Thickness)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	0	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	0	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	0	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	0	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	0	-

15 Aug, 2028

-
Included w.e.f 15.01.2025

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material)	-	500	-
3.2(Material)	-	500	-
3.3(Material)	-	500	-
3.4(Material)	-	500	-
3.4(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
3.5(Material)	-	500	-
4.1 (Annex A)(Shapes and Dimensions)	-	100	-
4.2 (Table 1)(Shapes and Dimensions)	-	100	-
4.2 (Table 1)(Shapes and Dimensions)	-	100	-
4.2(Shapes and Dimensions)	-	100	-
4.3(Shapes and Dimensions)	-	100	-
4.4(Shapes and Dimensions)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.1(Workmanship and Finish)	-	100	-
5.2(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.3(Workmanship and Finish)	-	100	-
5.4(Workmanship and Finish)	-	100	-
5.5(Workmanship and Finish)	-	100	-
5.6(Workmanship and Finish)	-	100	-
6.1(Staining Test)	-	1000	-
6.1(Staining Test)	-	1000	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	1000	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	1000	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	1000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	1000	-
6.6(3 Ply)	-	1000	-
6.7.1(Nominal Capacity Test)	-	1000	-
6.7.2(Nominal Capacity Test- Diameter)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	1000	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	1000	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	1000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	1000	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	1000	-
As per Clause 3(Carbon)	-	500	-
As per Clause 3(Silicon)	-	500	-
As per Clause 3(Manganese)	-	500	-
As per Clause 3(Nickel)	-	500	-
As per Clause 3(Chromium)	-	500	-
As per Clause 3(Sulphur)	-	500	-
As per Clause 3(phosphorus)	-	500	-
As per Clause 3(Nitrogen)	-	500	-
As per Clause 3(Titanium)	-	500	-
As per Clause 3(Aluminium)	-	500	-
As per Clause 3(Copper)	-	500	-
As per Clause 3(Magnesium)	-	500	-
As per Clause 3(Iron)	-	500	-
As per Clause 3(Zinc)	-	500	-
As per Clause 3(Arsenic)	-	500	-
As per Clause 3(Antimony)	-	500	-
As per Clause 3(Bismith)	-	500	-
As per Clause 3(Lead)	-	500	-
As per Clause 3(Tellurium)	-	500	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	100	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	100	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	100	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	100	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	100	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	100	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	100	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	100	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	100	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	100	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	100	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	100	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	100	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	100	-
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	0	-
4.4(Shapes and Dimensions)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	0	-
5.5(Workmanship and Finish)	-	0	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	0	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	0	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	0	-
6.5(Coating Thickness Test (For Copper Deposit))	-	0	-
6.6(3 Ply)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.7.2(Nominal Capacity Test- Diameter)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	0	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	0	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	0	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	0	-
As per Clause 3(Carbon)	-	0	-
As per Clause 3(Silicon)	-	0	-
As per Clause 3(Manganese)	-	0	-
As per Clause 3(Nickel)	-	0	-
As per Clause 3(Chromium)	-	0	-
As per Clause 3(Sulphur)	-	0	-
As per Clause 3(phosphorus)	-	0	-
As per Clause 3(Nitrogen)	-	0	-
As per Clause 3(Titanium)	-	0	-
As per Clause 3(Aluminium)	-	0	-
As per Clause 3(Copper)	-	0	-
As per Clause 3(Magnesium)	-	0	-
As per Clause 3(Iron)	-	0	-
As per Clause 3(Zinc)	-	0	-
As per Clause 3(Arsenic)	-	0	-
As per Clause 3(Antimony)	-	0	-
As per Clause 3(Bismith)	-	0	-
As per Clause 3(Lead)	-	0	-
As per Clause 3(Tellurium)	-	0	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	0	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	0	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	0	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	0	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	0	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	0	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	0	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	0	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	0	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	0	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	0	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	0	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	0	-
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	0	-
4.4(Shapes and Dimensions)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	0	-
5.5(Workmanship and Finish)	-	0	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	0	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	0	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	0	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	0	-
6.5(Coating Thickness Test (For Copper Deposit))	-	0	-
6.6(3 Ply)	-	0	-
6.7.1(Nominal Capacity Test)	-	0	-
6.7.2(Nominal Capacity Test- Diameter)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	0	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	0	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	0	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	0	-
As per Clause 3(Carbon)	-	0	-
As per Clause 3(Silicon)	-	0	-
As per Clause 3(Manganese)	-	0	-
As per Clause 3(Nickel)	-	0	-
As per Clause 3(Chromium)	-	0	-
As per Clause 3(Sulphur)	-	0	-
As per Clause 3(phosphorus)	-	0	-
As per Clause 3(Nitrogen)	-	0	-
As per Clause 3(Titanium)	-	0	-
As per Clause 3(Aluminium)	-	0	-
As per Clause 3(Copper)	-	0	-
As per Clause 3(Magnesium)	-	0	-
As per Clause 3(Iron)	-	0	-
As per Clause 3(Zinc)	-	0	-
As per Clause 3(Arsenic)	-	0	-
As per Clause 3(Antimony)	-	0	-
As per Clause 3(Bismith)	-	0	-
As per Clause 3(Lead)	-	0	-
As per Clause 3(Tellurium)	-	0	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	0	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	0	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	0	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	0	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	0	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	0	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	0	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	0	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	0	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	0	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	0	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	0	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	0	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	0	-

15 Aug, 2028

-
Included w.e.f 07.01.2025

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(General)	-	200	-
Clause 4.2(Material)	-	200	-
Clause 4.2.1(Lining)	-	200	-
Clause 4.2.2 (a)(Reinforcement)	-	500	-
Clause 4.2.2 (b)(Reinforcement)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	200	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	200	-
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	200	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	200	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	200	-
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	200	-
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	200	-
Clause 5.2.1(BIS Certification Marking )	-	200	-

15 Aug, 2028

-
Included w.e.f. 12.12.2024

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

14800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	200	-
Clause 4.1 (General)	-	200	-
Clause 4.1(General)	-	200	-
Clause 4.2(Material)	-	500	-
Clause 4.2.1(Lining)	-	500	-
Clause 4.2.2(Reinforcement)	-	500	-
Clause 4.2.3(Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	500	-
Clause 4.3 Sub Clause 4.3.3(Length)	-	500	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test cover)	-	1000	-
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.4 Sub Clause 4.4.3 (b)(Resistance of Lining to n-pentane)	-	1200	-
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	1000	-
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	-
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	-
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	-
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	1000	-
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	-
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	200	-
Clause 5.2 (b)(Marking Words LPG, Max W.P. 2.5 MPa; )	-	200	-
Clause 5.2 (c)(Marking Nominal bore )	-	200	-
Clause 5.2 (d)(Marking Batch/Lot No. )	-	200	-
Clause 5.2 (e)(Marking Month and year of manufacture )	-	200	-
Clause 5.2 (f)(Marking IS 9573 (Part 1) )	-	200	-
Clause 5.2.1(BIS Certification Marking )	-	200	-

15 Aug, 2028

-
Included w.e.f 18.12.2024

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.2 - Table 1(Bore size)	-	500	-
Cl. 3.2 - Table 1(Lining Thickness)	-	500	-
Cl. 3.2 - Table 1(Cover Thickness)	-	500	-
Cl. 3.2 - Table 1(Length %)	-	500	-
Cl. 3.3 - Table 2(Tensile strength - Lining MPA)	-	1000	-
Cl. 3.3 - Table 2(Tensile strength - Cover Mpa)	-	1000	-
Cl. 3.3 - Table 2(Elongation at break - Lining %)	-	1000	-
Cl. 3.3 - Table 2(Elongation at break - Cover %)	-	1000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining %)	-	1000	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover %)	-	1000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining %)	-	1000	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover %)	-	1000	-
Cl. 3.4 - Table3(Pressure Tests)	-	4000	-
Cl. 3.4 - Table3(Adhesion KN/m Min)	-	1000	-
Cl. 3.2 - Table 1(Bore size, mm)	-	0	-
Cl. 3.2 - Table 1(Lining Thickness, mm)	-	0	-
Cl. 3.2 - Table 1(Cover Thickness, mm)	-	0	-
Cl. 3.2 - Table 1(Length)	-	0	-
Cl. 3.3 - Table 2(Tensile strength - Lining, Mpa)	-	0	-
Cl. 3.3 - Table 2(Tensile strength - Cover, Mpa)	-	0	-
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	0	-
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	0	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	0	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	0	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	0	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	0	-
Cl. 3.4 - Table3(Pressure Tests)	-	0	-
Cl. 3.4 - Table3(Adhesion, KN/m Min)	-	0	-
Cl. 3.4 - Table3(Adhesion)	-	0	-
Cl. 3.4 - Table3(Pressure Tests)	-	0	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	0	-
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining)	-	0	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover)	-	0	-
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining)	-	0	-
Cl. 3.3 - Table 2(Elongation at break - Cover)	-	0	-
Cl. 3.3 - Table 2(Elongation at break - Lining)	-	0	-
Cl. 3.3 - Table 2(Tensile strength - Cover)	-	0	-
Cl. 3.3 - Table 2(Tensile strength - Lining)	-	0	-
Cl. 3.2 - Table 1(Length)	-	0	-
Cl. 3.2 - Table 1(Cover Thickness)	-	0	-
Cl. 3.2 - Table 1(Lining Thickness)	-	0	-
Cl. 3.2 - Table 1(Bore size)	-	0	-

15 Aug, 2028

-
Included w.e.f 09.10.2024

IS 3854 (2023)

Switches for Domestic and Similar Purposes - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	100	-
Cl-5(General notes on tests)	-	100	-
Cl-6(Rating)	-	250	-
Cl-7(Classification)	-	250	-
Cl-8(Marking)	-	250	-
Cl-9(Checking of dimensions)	-	500	-
Cl-10.1, 10.2(Prevention of Access to Live Parts)	-	500	-
Cl-10.3(Requirements for Accessible Metal Parts)	-	500	-
Cl-10.4(Requirements for Insulation of the Mechanism)	-	500	-
Cl. 10.5(Requirements for Insulation of the Mechanism with Respect to the Surrounding Environment)	-	500	-
Cl-10.6(Requirements for Switches Operated Indirectly)	-	500	-
Cl-10.7(Requirements for Switches with Replaceable Pull Cord)	-	500	-
Cl-11(Provision for earthing)	-	500	-
Cl-12(Terminals)	-	500	-
Cl-13(Constructional requirements)	-	500	-
Cl-14(Mechanism)	-	500	-
Cl-15.1(Resistance to Ageing)	-	500	-
Cl-15.2(Protection Provided by Enclosures of Switches)	-	500	-
Cl-15.3(Resistance to Humidity)	-	500	-
Cl-16.1(General)	-	500	-
Cl-16.2(Test for Measuring the Insulation Resistance)	-	500	-
Cl-16.3(Electric Strength Test)	-	500	-
Cl-17(Temperature rise)	-	500	-
Cl-18(Making and breaking capacity)	-	500	-
Cl-19(Normal operation)	-	500	-
Cl-20(Mechanical strength)	-	500	-
Cl-21(Resistance to heat)	-	500	-
Cl-22(Screws, current carrying parts and connections)	-	500	-
Cl-23(Creepage distances, clearances and distance through sealing compound)	-	500	-
Cl-24.1(Resistance to abnormal heat and fire)	-	500	-
Cl-24.2(Resistance to tracking)	-	500	-
Cl-25(Resistance to rusting)	-	500	-
19.1(Test for Switches Intended for Inductive Loads)	-	500	-
19.2(Test for Switches Intended for Externally Ballasted Lamp Loads)	-	500	-
19.3(Test for Switches Intended for Self-ballasted Lamp Loads)	-	500	-
13.5(Attachment of knobs)	-	250	-
12.3.11(Table 11)(Test Current for the Verification of Electrical and Thermal Stresses in Normal Use of Screwless Terminals)	-	250	-
12.3.12(Table 13)(Deflection Test Forces)	-	250	-

15 Aug, 2028

-
Included w.e.f. 02.09.2024

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

INDIAN TESTING LABORATORY PRIVATE LIMITED, GREATER NOIDA

Plot No-248 , Ecotech - III, Udyog Kendra - II, GREATER NOIDA, Gautam Buddha Nagar, Uttar Pradesh, 201306

9999669383 itlnoida.labs@gmail.com

Scope List