BIS - LIMS (Laboratory Information Management System)

ADS LABTECH, GHAZIABAD

39/2/10-A, Site-IV, Sahibabad Industrial Area, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

7217808235 shaktigroups@gmail.com

Scope List

Reset

28 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

FABRICATED PVC-U FITTINGS FOR POTABLE WATER SUPPLIES

5100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	2000	-
4(Size of fitting)	-	200	-
5.1 Table-1 Fig.1(Dimension of Socket length)	-	200	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	200	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	200	-
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	200	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	300	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1300	-
8(Marking)	-	0	-
3.2.3(socket, measurements)	-	200	-
3.1(Material)	-	2000	-
6.3(Effect on water test)	-	3000	-

15 May, 2027

-
Included w.e.f 24.02.2026

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

INJECTION MOULDED PVC SOCKET FITTINGS WITH SOLVENT CEMENT JOINTS FOR WATER SUPPLIES

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	100	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	100	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	100	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	100	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	500	-
Cl. 6.2(Opacity- Appendix B)	-	100	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	2000	All tests include of effect on water test
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	2000	All tests include of effect on water test
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	2000	All tests include of effect on water test
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	2000	All tests include of effect on water test
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	1000	-
6.1.1(VCM Content Test)	-	1000	-
3(Size of Fitting -)	-	100	-
4(Minimum thickness)	-	100	-
5(Socket dimensions)	-	100	-
6.1(Stress Relief Test)	-	500	-
6.2(Opacity)	-	100	-
6.3(Effect on Water)	-	2000	-
6.4(Short-Term Hydraulic Test)	-	800	-
7.2(Production Routine Tests)	-	500	-
Cl 6.3(Effect on Water Lead (first extraction))	-	2000	All tests include of effect on water test
Cl 6.3(Effect on Water Lead (third extraction))	-	2000	All tests include of effect on water test
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	2000	All tests include of effect on water test
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	2000	All tests include of effect on water test
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	2000	All tests include of effect on water test
CL 4.0(Wall thickness (average of 4.0))	-	100	-
CL 5.1(Sockt Length ( Take 4 reading and minimum will be reported))	-	100	-

15 May, 2027

-
Included w.e.f 17.02.2026

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

UNPLASTICIZED POLYVINYLCHLORIDE (UPVC) INJECTION MOULDEDFITTINGS

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.14, Annex A(Titanium Di-Oxide Content)	-	700	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	500	-
Cl.15, Annex B(Sulphated Ash Content)	-	500	-
12.4(Effect on water test)	-	3000	all included test of effect on water
Cl 12.4(Effect on Water Lead (first extraction))	-	3000	all included test of effect on water
Cl 12.4(Effect on Water Lead (third extraction))	-	3000	all included test of effect on water
Cl 12.4(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	3000	all included test of effect on water
Cl 12.4(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	3000	all included test of effect on water
Cl 12.4(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	3000	all included test of effect on water
19(Marking)	-	0	-
3(Type of Fitting)	-	200	-
4(Size Designation)	-	200	-
5(Colour of fittings)	-	200	-
7.1,Table 1(Wall thickness)	-	500	-
7.2 ,Table 2&3(Socket Dimensions)	-	200	-
7.3(Dimensions of waste trap(Nahani Trap)	-	200	-
8(Sealing Rings)	-	250	-
10(Workmanship)	-	0	-
11(Design requirements)	-	0	-
11.1(Solvent cement type or Rubber ring type)	-	500	-
11.2(Socket and spigot configeration)	-	200	-
11.4,Table 5(Vent cowl)	-	200	-
11.5,Table 6(Pipe Clips)	-	500	-
12(Physical test requirements)	-	1000	-
12.1(Visual appearance)	-	0	-
12.2(Stress relief test)	-	1000	-
12.3(Vicat softening tempewrature)	-	700	-
16(Mechanical Properties)	-	1000	-
16.1(Impact test)	-	1200	-
17(Watet tightness of joint)	-	1500	-
7.4(Chamfer)	-	200	-
11.3(Access Openings)	-	200	-
Table 4(Dimension of Access Openings)	-	300	-

15 May, 2027

-
Included w.e.f. 06.02.2026

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

Wrought Aluminium and Aluminium Alloy Sheet and Strip for General Engineering Purposes

5200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	100	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	3000	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	These tests are included in chemical composition
Cl. 7(Al - IS 504)	-	0	These tests are included in chemical composition
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	100	-
Cl. 4 (b)(Condition - IS 737)	-	100	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	100	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	100	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	100	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	100	-
Cl. 4 (g)(Packing Mode - IS 737)	-	100	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	100	-
Cl. 6(Freedom from Defects - IS 737)	-	300	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	1500	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	500	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	500	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	500	-
Cl. 8.2(Bend Test - IS 1599)	-	1000	-
Cl. 9(Condition - IS 737/ IS 5052)	-	0	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	300	-
Cl. 11(Selection of Test Samples - IS 737)	-	0	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	100	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	100	-
Cl. 12(Retests - IS 737/ IS 10259)	-	1500	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	100	-
Cl. 13.1(Marking - IS 737)	-	0	-

15 May, 2027

-
Included w.e.f. 27.01.2026

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

ROTATIONAL MOULDED POLYETHYLENE WATER STORAGE TANK.S

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	1000	-
4.2.3(Carbon Dispersion Test)	-	500	-
5(Types and Features )	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.3(Types and Features )	-	100	-
5.6(Types and Features )	-	100	-
6.1(Finish)	-	0	-
7.1.1(Resistance to Deformation)	-	1000	-
7.1.2(Resistance to Deformation)	-	1000	-
7.2(Resistance to Impact)	-	800	-
7.3(Test for Top Load Resistance)	-	900	-
7.4(Tensile Strength)	-	1000	-
7.5(Flexural Modulus)	-	1100	-
7.6(overall Migration)	-	2500	-
9.2.1(Man-Hole and Hand-Hole Lids)	-	200	-
9.2(Man-Hole and Hand-Hole Lids)	-	200	-
9.1(Man-Hole and Hand-Hole Lids)	-	200	-
9.1(Lid Thickness)	-	200	-
7.3(Test for Top Load Resistance)	-	400	-
6.1(Finish)	-	0	-
5.4(Wall Thickness above effective height)	-	200	-
5.2 Table 2 (7)(Minimum Wall Thickness)	-	200	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	-
4.2.1(Density)	-	500	-
4.2.2(MFI)	-	1000	-
7.6(overall Migration)	-	2500	-
4.1(MATERIALS)	-	2500	-
4.2.2(MFR)	-	1000	-
4.2.1(Density)	-	500	-
5.4(Wall Thickness)	-	200	-
10(MARKING)	-	0	-
Cl-7.6(Overall Migration)	-	2500	-
4.2.3(Carbon Black Content )	-	1000	-
4.2.3(Carbon Dispersion Test)	-	500	-
5(Types and Features )	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	500	-
5.3(Types and Features )	-	100	-
5.6(Types and Features )	-	100	-
6.1(Finish)	-	0	-
7.1.1(Resistance to Deformation)	-	1000	-
7.1.2(Resistance to Deformation)	-	1000	-
7.2(Resistance to Impact)	-	800	-
7.3(Test for Top Load Resistance)	-	800	-
7.4(Tensile Strength)	-	1000	-
7.5(Flexural Modulus)	-	1200	-
7.6(overall Migration)	-	2500	-
4.2.1(Density)	-	500	-
4.2.2(MFI)	-	1000	-
7.6(overall Migration)	-	2500	-
4.1(MATERIALS)	-	2500	-
4.2.2(MFR)	-	1000	-
4.2.1(Density)	-	500	-
5.4(Wall Thickness)	-	200	-
10(MARKING)	-	0	-
Cl-7.6(Overall Migration)	-	2500	-
4.2.3(Carbon Black Content )	-	1000	-
4.2.3(Carbon Dispersion Test)	-	500	-
5(Types and Features )	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	100	-
5.3(Types and Features )	-	0	this testing charge mention in above clause no-5
5.6(Types and Features )	-	0	this testing charge mention in above clause no-5
6.1(Finish)	-	200	-
7.1.1(Resistance to Deformation)	-	1000	For Cylindrical
7.1.2(Resistance to Deformation)	-	1000	For vertical
7.2(Resistance to Impact)	-	800	-
7.3(Test for Top Load Resistance)	-	800	-
7.4(Tensile Strength)	-	1000	-
7.5(Flexural Modulus)	-	1500	-
7.6(overall Migration)	-	2500	-
4.2.1(Density)	-	0	Mention in material test
4.2.2(MFI)	-	0	Mention in material test
7.6(overall Migration)	-	0	-
4.1(MATERIALS)	-	0	-
4.2.2(MFR)	-	0	-
4.2.1(Density)	-	0	-
5.4(Wall Thickness)	-	0	-
10(MARKING)	-	250	Our total testing charge 12500. we mention clause wise testing charge, but some clauses are repeated so consider clause wise rate.
Cl-7.6(Overall Migration)	-	0	-

15 May, 2027

-
Included w.e.f. 06.02.2026 Exclusion: Scope restricted to 5000 Ltr

IS 14268 (2022)

Uncoated stress relieved low relaxation seven-wire (ply) strand for prestressed concrete -Specification (Second Revision)

Uncoated Stress Relieved Low Relaxation Seven-Wire (Ply) Strand for Prestressed Concrete

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.3(Wire Description)	-	1000	-
4.1.4(Table 1)(Indentations Description)	-	1000	-
4.1.4(Table 1)(Nominal Depth of Oval Type Indentation)	-	1000	-
4.1.4(Table 1)(Length of Oval Type Indentation)	-	1000	-
4.1.4(Table 1)(Spacing Between Oval Type Indentations)	-	1000	-
4.2(Strand Lay Length)	-	1000	-
4.2(Difference In Diameter Of Centre Wire And Surrounding Wire Of Strand)	-	1000	-
4.2(Forming of wire)	-	1000	-
4.3(Joints)	-	1000	-
4.5(Workmanship and Finish)	-	1000	-
6(Table 2)(Diameter)	-	1000	-
6(Table 2)(Tensile Strength)	-	3000	-
6(Table 2)(Cross Sectional Area)	-	1000	-
6(Table 2)(Mass Per Meter)	-	1000	-
6(Table 2)(Breaking Load)	-	3000	-
6(Table 2)(0.2 Percent Proof Load)	-	3000	-
6.2.3(Elongation)	-	3000	-
6.2.4(Relaxation Properties(Relaxation Loss-100h))	-	15000	Relaxation test (100 hrs)- 15000
6.2.4(Relaxation Properties(Relaxation Loss-1000h))	-	100000	Relaxation test (1000 hrs)- 100000
6.3(Straightness of Strand)	-	1000	-
6.4(Behavior During Cutting)	-	1000	-
4.1.2(Carbon)	-	1000	-
4.1.2(Silicon)	-	1000	-
4.1.2(Manganese)	-	1000	-
4.1.2(Sulphur)	-	1000	-
4.1.2(Phosphorus)	-	1000	-
4.1.2(Chromium)	-	1000	-
4.1.2(Nickel)	-	1000	-
4.1.2(Molybdenum)	-	1000	-
4.1.2(Copper)	-	1000	-
4.1.2(Aluminum)	-	1000	-
4.1.2(Sulphur + Phosphorus)	-	1000	-
4.1.2(Boron)	-	1000	-
4.1.2(Titanium)	-	1000	-
4.1.2(Niobium)	-	1000	-
4.1.2(Vanadium)	-	1000	-
4.1.2(Titanium+Niobium+Vanadium)	-	1000	-
4.1.2(Nitrogen)	-	1000	-
4.1.3(Wire Description)	-	300	-
4.1.4(Table 1)(Indentations Description)	-	1000	-
4.1.4(Table 1)(Nominal Depth of Oval Type Indentation)	-	1000	-
4.1.4(Table 1)(Length of Oval Type Indentation)	-	1000	-
4.1.4(Table 1)(Spacing Between Oval Type Indentations)	-	1000	-
4.2(Strand Lay Length)	-	1000	-
4.2(Difference In Diameter Of Centre Wire And Surrounding Wire Of Strand)	-	1000	-
4.2(Forming of wire)	-	1000	-
4.3(Joints)	-	300	-
4.5(Workmanship and Finish)	-	200	-
6(Table 2)(Diameter)	-	200	-
6(Table 2)(Tensile Strength)	-	3000	-
6(Table 2)(Cross Sectional Area)	-	500	-
6(Table 2)(Mass Per Meter)	-	300	-
6(Table 2)(Breaking Load)	-	3000	-
6(Table 2)(0.2 Percent Proof Load)	-	3000	-
6.2.3(Elongation)	-	3000	-
6.2.4(Relaxation Properties(Relaxation Loss-100h))	-	30000	-
6.2.4(Relaxation Properties(Relaxation Loss-1000h))	-	95000	-
6.3(Straightness of Strand)	-	300	-
6.4(Behavior During Cutting)	-	300	-
4.1.2(Carbon)	-	2200	-
4.1.2(Silicon)	-	2000	-
4.1.2(Manganese)	-	1300	-
4.1.2(Sulphur)	-	1200	-
4.1.2(Phosphorus)	-	1400	-
4.1.2(Chromium)	-	800	-
4.1.2(Nickel)	-	1000	-
4.1.2(Molybdenum)	-	1000	-
4.1.2(Copper)	-	500	-
4.1.2(Aluminum)	-	1200	-
4.1.2(Sulphur + Phosphorus)	-	1000	-
4.1.2(Boron)	-	1000	-
4.1.2(Titanium)	-	1000	-
4.1.2(Niobium)	-	1000	-
4.1.2(Vanadium)	-	1000	-
4.1.2(Titanium+Niobium+Vanadium)	-	1000	-
4.1.2(Nitrogen)	-	1000	-
4.1.3(Wire Description)	-	0	-
4.1.4(Table 1)(Indentations Description)	-	500	-
4.1.4(Table 1)(Nominal Depth of Oval Type Indentation)	-	200	-
4.1.4(Table 1)(Length of Oval Type Indentation)	-	200	-
4.1.4(Table 1)(Spacing Between Oval Type Indentations)	-	200	-
4.2(Strand Lay Length)	-	200	-
4.2(Difference In Diameter Of Centre Wire And Surrounding Wire Of Strand)	-	200	-
4.2(Forming of wire)	-	0	-
4.3(Joints)	-	200	-
4.5(Workmanship and Finish)	-	0	-
6(Table 2)(Diameter)	-	300	-
6(Table 2)(Tensile Strength)	-	3000	Included tensile strength
6(Table 2)(Cross Sectional Area)	-	3000	Included tensile strength
6(Table 2)(Mass Per Meter)	-	3000	Included tensile strength
6(Table 2)(Breaking Load)	-	3000	Included tensile strength
6(Table 2)(0.2 Percent Proof Load)	-	3000	Included tensile strength
6.2.3(Elongation)	-	3000	Included tensile strength
6.2.4(Relaxation Properties(Relaxation Loss-100h))	-	20000	-
6.2.4(Relaxation Properties(Relaxation Loss-1000h))	-	100000	-
6.3(Straightness of Strand)	-	200	-
6.4(Behavior During Cutting)	-	0	-
4.1.2(Carbon)	-	2000	-
4.1.2(Silicon)	-	1000	-
4.1.2(Manganese)	-	1000	-
4.1.2(Sulphur)	-	1200	-
4.1.2(Phosphorus)	-	2000	-
4.1.2(Chromium)	-	2000	-
4.1.2(Nickel)	-	2000	-
4.1.2(Molybdenum)	-	2000	-
4.1.2(Copper)	-	2000	-
4.1.2(Aluminum)	-	2000	-
4.1.2(Sulphur + Phosphorus)	-	2000	-
4.1.2(Boron)	-	2000	-
4.1.2(Titanium)	-	2000	-
4.1.2(Niobium)	-	2000	-
4.1.2(Vanadium)	-	2000	-
4.1.2(Titanium+Niobium+Vanadium)	-	2000	-
4.1.2(Nitrogen)	-	2000	-
4.1.3(Wire Description)	-	0	-
4.1.4(Table 1)(Indentations Description)	-	0	-
4.1.4(Table 1)(Nominal Depth of Oval Type Indentation)	-	0	-
4.1.4(Table 1)(Length of Oval Type Indentation)	-	0	-
4.1.4(Table 1)(Spacing Between Oval Type Indentations)	-	0	-
4.2(Strand Lay Length)	-	0	-
4.2(Difference In Diameter Of Centre Wire And Surrounding Wire Of Strand)	-	0	-
4.2(Forming of wire)	-	0	-
4.3(Joints)	-	0	-
4.5(Workmanship and Finish)	-	0	-
6(Table 2)(Diameter)	-	0	-
6(Table 2)(Tensile Strength)	-	0	-
6(Table 2)(Cross Sectional Area)	-	0	-
6(Table 2)(Mass Per Meter)	-	0	-
6(Table 2)(Breaking Load)	-	0	-
6(Table 2)(0.2 Percent Proof Load)	-	0	-
6.2.3(Elongation)	-	0	-
6.2.4(Relaxation Properties(Relaxation Loss-100h))	-	0	-
6.2.4(Relaxation Properties(Relaxation Loss-1000h))	-	0	-
6.3(Straightness of Strand)	-	0	-
6.4(Behavior During Cutting)	-	0	-
4.1.2(Carbon)	-	0	-
4.1.2(Silicon)	-	0	-
4.1.2(Manganese)	-	0	-
4.1.2(Sulphur)	-	0	-
4.1.2(Phosphorus)	-	0	-
4.1.2(Chromium)	-	0	-
4.1.2(Nickel)	-	0	-
4.1.2(Molybdenum)	-	0	-
4.1.2(Copper)	-	0	-
4.1.2(Aluminum)	-	0	-
4.1.2(Sulphur + Phosphorus)	-	0	-
4.1.2(Boron)	-	0	-
4.1.2(Titanium)	-	0	-
4.1.2(Niobium)	-	0	-
4.1.2(Vanadium)	-	0	-
4.1.2(Titanium+Niobium+Vanadium)	-	0	-
4.1.2(Nitrogen)	-	0	-

15 May, 2027

-
Included w.e.f 24.02.2026

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

Irrigation Equipment — Polyethylene Pipes for Irrigation Laterals

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	100	.
Cl-4.2(Carbon content of finished PE lateral pipe)	-	1000	.
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	1000	.
Cl-6.0(Visual Appearance)	-	1000	.
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	1000	.
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1000	.
Cl-7.2(Reversion Test)	-	1000	.
Cl-7.3(Tensile Test)	-	1000	.
Cl-7.3.1(Test Piece)	-	1000	.
Cl-7.3.2(Procedure)	-	1000	.
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1000	.
Cl-8.0(Supply of pipes)	-	1000	.
Cl-9.0(Coiling)	-	1000	.
Cl-10.0(Sampling and criteria for conformity)	-	1000	.
Cl-11(Marking)	-	1000	.
3(Class of Pipe)	-	1000	.
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	1000	.
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	1000	.
6(Visual Appearance)	-	1000	.
7.1 & Table 2(Hydraulic Characteristics)	-	1000	.
7.1 & Table 2(Hydraulic Characteristics)	-	1000	.
7.2(Reversion Test)	-	1000	.
7.3(Tensile Strength)	-	1000	.
7.3(Elongation at Break)	-	1000	.
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1000	.
4.2(a)(Carbon Black Content-IS 2530)	-	1000	.
4.2(b)(Carbon Black Dispersion-IS 2530)	-	1000	.

15 May, 2027

-
Included w.e.f. 06.02.2026

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

UNPLASTICIZEDNON-PRESSUREPOLYVINYL CHLORIDE( PVC-U) PIPES FORUSEIN UNDERGROUNDDRAINAGEANDSEWERAGE SYSTEMS

21300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1000	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	1000	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	1000	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	1000	-
6.1.3 (Length of Pipe)	-	1000	-
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	1000	-
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	1000	-
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	1000	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	1000	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	1000	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	1000	-
6.1.4.1 (e3min=0.75e)	-	1000	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	1000	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	1000	-
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	1000	-
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	1000	-
7(Physical characteristics )	-	1000	-
7.1(Appearance:- )	-	1000	-
7.1(Appearance:- )	-	1000	-
7.2(Colour )	-	1000	-
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1000	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1000	-
8(MECHANICAL CHARACTERISTICS)	-	1000	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1000	-
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	1000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	1000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	1000	-
9.2 IS 14182(b) Solvent cement)	-	1000	-
10(Performance requirements)	-	1000	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	-
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1000	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	-
'7.5 (amdt.7)(Effect on Water (Type test))	-	1000	-
5.3(Qualitative)	-	1000	-
12(Marking)	-	1000	-
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	2000	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	all dimensions
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	500	all dimensions
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	500	all dimensions
6.1.3 (Length of Pipe)	-	500	all dimensions
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	500	all dimensions
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	100	.
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	100	.
6.1.4, Table 3(iv) Length of spigot, l1)	-	100	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	100	.
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	100	.
6.1.4.1 (e3min=0.75e)	-	100	.
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	100	.
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	100	.
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	100	.
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	100	.
7(Physical characteristics )	-	100	.
7.1(Appearance:- )	-	0	.
7.1(Appearance:- )	-	0	.
7.2(Colour )	-	0	.
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	500	.
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	500	.
8(MECHANICAL CHARACTERISTICS)	-	1000	.
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1200	.
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1200	.
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	3000	.
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	5000	.
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	100	.
9.2 IS 14182(b) Solvent cement)	-	200	.
10(Performance requirements)	-	500	.
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	.
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	2300	.
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	2300	.
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	2300	.
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	.
5.3(Qualitative)	-	0	.
12(Marking)	-	0	.
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	300	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	100	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	100	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	100	-
6.1.3 (Length of Pipe)	-	100	-
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	500	-
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	300	-
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	200	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	200	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	200	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	200	-
6.1.4.1 (e3min=0.75e)	-	200	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	200	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	200	-
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	200	-
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	200	-
7(Physical characteristics )	-	500	-
7.1(Appearance:- )	-	0	-
7.1(Appearance:- )	-	0	-
7.2(Colour )	-	0	-
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	700	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	800	-
8(MECHANICAL CHARACTERISTICS)	-	1000	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1000	-
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	400	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	2000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	5000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	1000	-
9.2 IS 14182(b) Solvent cement)	-	200	-
10(Performance requirements)	-	1000	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	-
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1000	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	-
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	-
5.3(Qualitative)	-	0	-
12(Marking)	-	0	-

15 May, 2027

-
Included w.e.f 30.01.2026

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
6(FREEDOM FROM DEFECTS)	-	500	-
Cl. 9(Aluminium)	-	500	-
Cl. 9(Copper)	-	500	-
Cl. 9(Magnesium)	-	500	-
Cl. 9(Silicon)	-	500	-
Cl. 9(Iron)	-	500	-
Cl. 9(Manganese)	-	500	-
Cl. 9(Zinc)	-	500	-
Cl. 9(Titanium and/or other grain refining elements)	-	500	-
Cl. 9(Chromium)	-	500	-
Cl. 9(Ti+V)	-	500	-
Cl. 9(Cr+Mn)	-	500	-
Clause-10(Tensile strength)	-	500	-
8(DIMENSIONS AND TOLERANCES)	-	500	-
10(MECHANICAL PROPERTIES)	-	500	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	-	-
6(FREEDOM FROM DEFECTS)	-	-	-
Cl. 9(Aluminium)	-	-	-
Cl. 9(Copper)	-	-	-
Cl. 9(Magnesium)	-	-	-
Cl. 9(Silicon)	-	-	-
Cl. 9(Iron)	-	-	-
Cl. 9(Manganese)	-	-	-
Cl. 9(Zinc)	-	-	-
Cl. 9(Titanium and/or other grain refining elements)	-	-	-
Cl. 9(Chromium)	-	-	-
Cl. 9(Ti+V)	-	-	-
Cl. 9(Cr+Mn)	-	-	-
Clause-10(Tensile strength)	-	-	-
8(DIMENSIONS AND TOLERANCES)	-	-	-
10(MECHANICAL PROPERTIES)	-	-	-

15 May, 2027

-
Included w.e.f. 06.02.2026

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

Test facility available only for nominal pipe dia upto and including 500mm.

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Pipe Description - IS 14333-2022)	-	1000	-
6.2(Colour- IS 14333-2022)	-	1000	-
7.1(Visual Appearance- IS 14333-2022)	-	1000	-
7.2(Length- IS 14333-2022)	-	1000	-
7.3(Coiling- IS 14333-2022)	-	1000	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	1000	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	1000	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	1000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	1000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	1000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	1000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1000	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1000	-
8.3(Carbon black content- IS 2530-1963)	-	1000	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	1000	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1000	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	1000	-
8.6(Density-IS 7328:2020)	-	1000	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1000	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1000	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1000	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	1000	-
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1000	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1000	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	1000	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	1000	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	1000	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	1000	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	1000	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	1000	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	1000	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	1000	-
5.2.1.1, T2(Compound ash content - Any Method)	-	1000	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	1000	-
5.3(Density of Higher olefin - IS 7328:2020)	-	1000	-
5.3(Olefin Constituents- 14333-2022)	-	1000	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	1000	-
5.3(Ash content- Any Method)	-	1000	-
5.3(Toluene extract - Any Method)	-	1000	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	1000	-
5.3(Carbon black particle size - Any Method)	-	1000	-
5.4(Antioxidant - Any Method)	-	1000	-

15 May, 2027

-
included w.e.f 17-12-2025.

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

Wrought Aluminium and Aluminium Alloy Bars, Rods and Sections

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	500	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	500	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	500	-
7(Dimension - IS 3965)	-	500	-
Cl. 4(Freedom from Defects)	-	500	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	500	-
11(Marking)	-	500	-
Table-1, Clause - 5.1(Copper)	-	500	-
Table-1, Clause - 5.1(Iron)	-	500	-
Table-1, Clause - 5.1(Magnesium)	-	500	-
Table-1, Clause - 5.1(Manganese)	-	500	-
Table-1, Clause - 5.1(Titanium)	-	500	-
Table-1, Clause - 5.1(Silicon)	-	500	-
Table-1, Clause - 5.1(Chromium)	-	500	-
Table-1, Clause - 5.1(Zinc)	-	500	-

15 May, 2027

-
Included w.e.f 31.12.2025

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

Polyethylene Films and Sheets

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	1000	.
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	1000	.
5.1.6(Ash content - IS 2508: 2024)	-	1000	.
5.1.6(carbon black dispersion - IS 2530: 1963)	-	1000	.
5.1.1(Appearance)	-	1000	.
5.1.2(Film Form)	-	1000	.
5.1.3(Odour)	-	1000	.
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	1000	.
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	1000	.
5.2.1.2(Nominal Width)	-	1000	.
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	1000	.
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1000	.
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1000	.
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1000	.
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	1000	.
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1000	.
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	1000	.
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1000	.
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	1000	.
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	1000	.
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1000	.

15 May, 2027

-
Included w.e.f 11.12.2025

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPES FOR POTABLE HOT AND COLD WATER DISTRIBUTION SUPPLIES

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2.1 Annex B(Chloride Content of Resin)	-	3000	.
6.3(Compound Properties)	-	5000	.
6.3.1 Annex B(Chloride content)	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	3000	..
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	3000	.
6.2.1 Annex B(Chloride Content of Resin)	-	3000	.
5 Table 1(Classification of pipes)	-	1000	.
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	1000	.
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	1000	.
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	1000	.
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	1000	.
7.1.3 (Effective length)	-	1000	.
8(Pipe Ends)	-	1000	.
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	1000	.
9.1(Visual Appearance)	-	1000	.
9.1(Visual Appearance)	-	1000	.
9.2 IS 12235 (Part 3)(Opacity)	-	1000	.
6.3(Compound Properties)	-	5000	.
6.3.1 Annex B(Chloride content)	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	3000	.
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	3000	.
6.3(K value Test)	-	3000	.
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	1000	.
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1000	.
9.6 IS 12235(Part 14)(Density)	-	1000	.
10(Mechanical Properties)	-	1000	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	.
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	1000	.
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1000	.
10.4 IS 12235(Part 19)(Flattening Test)	-	1000	.
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	3000	.
5 Table 1(Classification of pipes)	-	1000	.
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	1000	.
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	1000	.
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	1000	.
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	1000	.
7.1.3 (Effective length)	-	1000	.
8.0(Pipe Ends)	-	1000	.
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	1000	.
9.1(Visual Appearance)	-	1000	.
9.1(Visual Appearance)	-	1000	.
9.2 IS 12235 (Part 3)(Opacity)	-	1000	.
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	1000	.
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1000	.
9.6 IS 12235(Part 14)(Density)	-	1000	.
10.0(Mechanical Properties)	-	1000	.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	1000	.
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	1000	.
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1000	.
10.4 IS 12235(Part 19)(Flattening Test)	-	1000	.
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1000	.
7.1.2(Wall Thickness (Maximum))	-	1000	.
7.1.1(Outside Diameter at any point (Maximum))	-	1000	.
6.3.3(Density)	-	1000	.
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	1000	-
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	1000	.

15 May, 2027

-
Included w.e.f 17-12-2025.

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

UNPLASTICIZED POLYVINYL CHLORIDE (PVC-U) PIPES FOR SOIL AND WASTE DISCHARGE SYSTEM FOR INSIDE AND OUTSIDE BUILDINGS INCLUDING VENTILATION AND RAIN WATER SYSTEM

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	.
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1500	.
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	1000	.
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	1000	.
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	1000	.
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	1000	.
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	1000	.
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	1000	.
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	1000	.
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	2000	.
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	2000	.
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	2000	.
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	5000	1600 hour-approx 7 month
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	1000	.
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1000	.
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1000	.
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	1000	.
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	.
8.6(Effect on Water Test)	-	2500	.
Cl 8.6(Effect on Water Lead (first extraction))	-	2500	.
Cl 8.6(Effect on Water Lead (first extraction))	-	2500	.
Cl 8.6(Effect on Water Lead (third extraction))	-	2500	.
Cl 8.6(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	2500	.
Cl 8.6(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	2500	.
Cl 8.6(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	2500	.
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	.
14(Marking)	-	1000	.
CL 7.3(Socket length (Take 4 reading & minimum will be reported))	-	1000	.
CL 7.3.1(Socket wall Thickness For S2 and S3 (Take 4 reading and average will be reported))	-	1000	.
CL 7.3.2 grooved sockets(Inside diameter of Sockets, D1 (Take 4 reading & minimum, Maximum will be reported))	-	1000	.
CL 7.3.2 grooved sockets(Inside diameter of beading D2 (Take 4 reading & minimum, Maximum will be reported))	-	1000	.
CL 7.3.2 grooved sockets(Length of beading and Neck A (Take 4 reading & Maximum will be reported))	-	1000	.
CL 7.3.2 grooved sockets(Neck of Socket B (Take 4 reading & minimum, will be reported))	-	1000	.
CL 7.3.2 grooved sockets(Length beyond beading C (Take 4 reading & minimum will be reported))	-	1000	.

15 May, 2027

-
included w.e.f 05.01.2026

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

UNPLASTICIZEDPOLYVINYLCHLORIDE(PVC-U) SCREENANDCASINGPIPESFOR BORE/TUBEWELLS

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1000	.
9.5(Tensile Strength IS 12235(Part 13))	-	3000	.
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1000	.
9.3(Density IS 12235 (Part 14))	-	1000	.
9.2(Internal Diameter)	-	1000	.
9.1( Visual Appearance)	-	1000	.
9.1(Visual Appearance)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	1000	.
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	1000	.
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	1000	.
5(COLOUR)	-	1000	.
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	1000	.
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	1000	.
5.0(Colour of Pipes)	-	1000	.
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	2500	.
4.1.2(K-Value as per IS-4669)	-	1000	.
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	1000	.
7.1(Screen Pipes)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	1000	.
8.4(Sealing rings - Hardness)	-	1000	.
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	1000	.
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	1000	.
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	1000	.
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	1000	.
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	1000	.
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	1000	.
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	1000	.
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	1000	.
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	1000	.
7.3.2(Rib height)	-	1000	.
7.3.1(No.of Ribs)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	1000	.
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	1000	.
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	1000	.
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	1000	.
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	1000	.
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	1000	.
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	1000	.
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	1000	.
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	1000	.
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	1000	.
11(Marking)	-	1000	.
5.1(Materials)	-	1000	.
8(Packing)	-	1000	.
4.1.3(Cross Chain Length)	-	1000	.
7.2(Link Twisted (Cross chain))	-	1000	.
7.3(The Basic chains)	-	1000	.
7.9(Case Depth)	-	1000	.
8(Marking)	-	1000	.
Cl 9.7(Effect on Water Lead (first extraction))	-	3000	.
Cl 9.7(Effect on Water Lead (third extraction))	-	3000	.
Cl 9.7(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	3000	.
Cl 9.7(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	3000	.
Cl 9.7(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	3000	.
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	1000	.
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	1000	.
8.4(Width b)	-	1000	.

15 May, 2027

-
Included w.e.f 11.12.2025

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Anti-oxidant)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	4000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	1000	-
5(Dimensions of pipe - i) Outside diameter)	-	500	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
6(Visual Appearance)	-	200	-
7.1(Hydraulic Characteristics - Quality test)	-	2000	-
7.1(Hydraulic Characteristics - Acceptance test)	-	2000	-
7.2(Reversion Test)	-	500	-
7.3(Tensile Test- i) Tensile Strength)	-	2000	-
7.3(Tensile Test - ii)Elongation at Break)	-	2000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	2000	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	2000	-
7.5(Density)	-	500	-
7.6(Melt Flow Rate)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
4.2(Carbon black- a)carbon content)	-	1000	-
4.2(Carbon black- b) Dispersion of carbon black)	-	1000	-
7.6(Melt now Rate (MFR))	-	10005	-
7.5(Density)	-	500	-
7.4 Table-2(Fusion Compatibility Test)	-	2000	-
7.3(Tensile Test)	-	2000	-
7.2(Reversion Test)	-	500	-
7.1 Table -2(Hydraulic Characteristics)	-	2000	-
6.1(VISUAL APPEARANCE)	-	200	-
5.1.2(Ovality)	-	200	-
5.1 table -1(DIMENSIONS OF PIPES)	-	200	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	1000	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1000	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
3(CLASSIFICATION OF PIPES)	-	200	-
4.1(Quick Coupled Male and Female Couplers)	-	200	-
4.1(Quick Coupled Male and Female Couplers)	-	500	-
4.1.3(Workmanship and appearance)	-	200	-
4.1.4(Holding attachments for coupler parts)	-	5000	-
6.1.3(Weldability Test- a) Quality test)	-	2000	-
6.1.3(Weldability Test- b) Acceptance test)	-	2000	-
3(Quick Coupled pipes)	-	200	-
3(QUICK COUPLED PIPES)	-	200	-
4(QUICK COUPLED FITTINGS)	-	200	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	200	-
4.1 (b)(HDPE couplers —)	-	200	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	200	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	-
4.1 .1.2.1(HDPE couplers)	-	1000	-
4.1 .1.2.2(HDPE couplers)	-	1000	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	1000	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	1000	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	1000	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	1000	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	1000	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	1000	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	1000	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	1000	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
6.1(Volatile Matter)	-	1000	-
6.1(Water content)	-	1000	-
6.2.1(Volatile Matter x 2)	-	1000	-
6.2.1(Water content x 2)	-	1000	-
4.1.1 (Table-1)(Volatile Matter)	-	1000	-
4.1.1 (Table-1)(Water content)	-	1000	-
4.1.3, Table 1,(iv)(Volatile matter)	-	1000	-
4.1.3, Table 1,(v)(Water content)	-	1000	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	500	-
6.1(Quick Coupled Pipes and Fittings)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	2000	-
6.1.1, 6.1.1.1(Leakage Test)	-	2000	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	2000	-
6.1.2.2(Hydraulic Proof Test)	-	2000	-
6.1.2.2(Hydraulic Proof Test)	-	2000	-
6.1.3, 6.1.3.1(Weldability Test)	-	2000	-
6.1.3.1.1(Weldability Test)	-	2000	-
6.1.3.2(Quick coupled fittings)	-	2000	-
6.2, 6.2.1(Quick Coupled Fittings)	-	2000	-
7.2.1(Visual and Workmanship Requirement)	-	200	-
6.2 b(Material Identification - Male & Female Coupler)	-	500	-
6.3.3(Material Identification - Insert Valve Coupler)	-	500	-
6.3.3(Material Identification - Insert Valve Coupler)	-	500	-
6.3.4()	-	500	-
6.3.5(Material Identification - Saddle)	-	500	-
6.3.5(Material Identification - Pipe Ends)	-	500	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	500	-
4.2(Metallic Couplers)	-	500	-
4.2(Metallic Couplers)	-	500	-
7.2.1(Leakage Test)	-	2000	-
Cl.4.1.3(Den sity Test)	-	500	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
6.1(Thermal Stability (OIT))	-	2000	-
6.1(Carbon Black Content)	-	1000	-
6.1(Carbon Black Dispersion)	-	1000	-
6.2.1(Melt Flow Index x 2)	-	1000	-
6.2.1(Thermal Stability (OIT) x 2)	-	1000	-
6.2.1(Carbon Black Content x 2)	-	1000	-
6.2.1(Carbon Black Dispersion x 2)	-	1000	-
7.1.3(Reversion)	-	500	-
6.2.5(Material Composition (Chemical Analysis))	-	1000	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	1000	-
Cl.5(Di men sion)	-	500	-
Cl.5.1.l(Outside Diameter)	-	500	-
Cl.5.1.l(Outside Diameter)	-	500	-
Cl.6.2.L(Wall Thickness)	-	500	-
Cl.6.2.4(Workmanship and Appearance)	-	500	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-
Cl.6.2.6(Ageing Test)	-	500	-
Cl.7.1.l(Visual Anneara nce)	-	500	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
Cl.7.1.2(Hydraulic Characteristic)	-	2000	-
7.1.6(Carbon black Content)	-	1000	-
7.1.7(Melt Flow Rate (MFR))	-	1000	-
7.2.1(Leakage test 1hour / 27°C)	-	2000	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	2000	-
4.1.1 (Table-1)(Melt Flow Index)	-	1000	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	2000	-
4.1.4(Carbon Black Content)	-	1000	-
4.1.4(Carbon Black Dispersion)	-	1000	-
4.1.1(Polyethylene material)	-	1000	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1000	-
4.1.3, Table 1,(iii)(Thermal stability)	-	1000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Tensile Test)	-	2000	-
Cl.7.1.4(Elongation)	-	2000	-
Cl.7.1.4(Elongation)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.5(Fusion Compatibility)	-	2000	-
Cl.7.1.6(Corrected Density)	-	500	-
4.1.4(The Carbon Content and Dispersion)	-	1000	-
4.1.5(Carbon Black Specification)	-	1000	-
4.1.6(Antioxidant)	-	1000	-
7.1.3(Reversion Test)	-	500	-
Cl.7.2.2(Cl.7.2.2)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	2000	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	2000	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	200	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	500	-
6.1(Tensile strength at Yield & Elongation at break)	-	2000	-
6.2.1(Base Density x 2)	-	500	-
7.1.7(Melt flow rate)	-	1000	-
7.2.1(Leakage Test)	-	2000	-
7.2.2(Hydraulic Proof Test)	-	2000	-
7.2.3(Weldability Test)	-	2000	-
6.2.1(Wall thickness of male & female coupler)	-	500	-
6.2.4(Workmanship and appearance (Visual))	-	200	-
6.2.5(Holding attachment for coupler parts)	-	5000	-
7.3(Quick Couple Fitting)	-	200	-
10(Marking)	-	200	-
5.1.2(Squareness)	-	200	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	500	-
7.1.4(Tensile Test)	-	2000	-
7.1.5(Fusion Compatibility Test)	-	2000	-
6.2.6(Material Identification (Chemical Analysis))	-	200	-
6.2.6(Color)	-	200	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	500	-
6.2.6(Ageing Charges for rubber ring)	-	500	-
7.1.1(Visual appearance of pipes)	-	200	-
7.1.2(Hydraulic Characteristics)	-	2000	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	..
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
7.1.4(Tensile strength & elongation)	-	2000	.
7.1.5(Fusion Compatibility test)	-	2000	.
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	.
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
7.1.6(Corrected Density)	-	500	.
7.1.6(Base Density)	-	500	.
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	2000	.
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	2000	.
8(Supply of pipe (Visual))	-	200	.
4.1.1 (Table-1)(Density)	-	500	.
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	2000	.
4.1.3, Table 1,(i)(Bass density)	-	500	.
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	2000	.
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	2000	.
4.1.7(Rework Material)	-	500	.
4.2(Metallic Couplers)	-	500	.
5.1, Table 1,(i)(Plain pipes)	-	500	.
5.1, Table 1,(ii)(90° Bends and tee)	-	500	.
5.1, Table 1,(iii)(Base pipe )	-	500	.
5.1, Table 1,(iv)(PCN)	-	500	.
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	500	.
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	500	.
5.1, Table 1,(vii)(Riser pipe and socket)	-	500	.
7.1.1(Visual Appearance and Workmanship)	-	500	.
7.1.2(Hydraulic Performance Characteristic)	-	2000	..
7.1.6(Corrected Density)	-	500	.
4.3(Anti-oxidant)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	1000	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	1000	-
5(Dimensions of pipe - i) Outside diameter)	-	1000	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	1000	-
6(Visual Appearance)	-	1000	-
7.1(Hydraulic Characteristics - Quality test)	-	1000	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test- i) Tensile Strength)	-	1000	-
7.3(Tensile Test - ii)Elongation at Break)	-	1000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	1000	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	1000	-
7.5(Density)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
7.6(Melt Flow Rate)	-	1000	-
4.2(Carbon black- a)carbon content)	-	1000	-
4.2(Carbon black- b) Dispersion of carbon black)	-	1000	-
7.6(Melt now Rate (MFR))	-	1000	-
7.5(Density)	-	1000	-
7.4 Table-2(Fusion Compatibility Test)	-	1000	-
7.3(Tensile Test)	-	1000	-
7.2(Reversion Test)	-	1000	-
7.1 Table -2(Hydraulic Characteristics)	-	1000	-
6.1(VISUAL APPEARANCE)	-	1000	-
5.1.2(Ovality)	-	1000	-
5.1 table -1(DIMENSIONS OF PIPES)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	1000	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	1000	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1000	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1000	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
3(CLASSIFICATION OF PIPES)	-	1000	-
4.1(Quick Coupled Male and Female Couplers)	-	1000	-
4.1(Quick Coupled Male and Female Couplers)	-	1000	-
4.1.3(Workmanship and appearance)	-	1000	-
4.1.4(Holding attachments for coupler parts)	-	1000	-
6.1.3(Weldability Test- a) Quality test)	-	1000	-
6.1.3(Weldability Test- b) Acceptance test)	-	1000	-
3(Quick Coupled pipes)	-	1000	-
3(QUICK COUPLED PIPES)	-	1000	-
4(QUICK COUPLED FITTINGS)	-	1000	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	1000	-
4.1 (b)(HDPE couplers —)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	1000	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	-
4.1 .1.2.1(HDPE couplers)	-	1000	-
4.1 .1.2.2(HDPE couplers)	-	1000	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	1000	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	1000	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	1000	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	1000	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	1000	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	1000	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	1000	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	1000	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	1000	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
6.1(Volatile Matter)	-	1000	-
6.1(Water content)	-	1000	-
6.2.1(Volatile Matter x 2)	-	1000	-
6.2.1(Water content x 2)	-	1000	-
4.1.1 (Table-1)(Volatile Matter)	-	1000	-
4.1.1 (Table-1)(Water content)	-	1000	-
4.1.3, Table 1,(iv)(Volatile matter)	-	1000	-
4.1.3, Table 1,(v)(Water content)	-	1000	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	1000	-
6.1(Quick Coupled Pipes and Fittings)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	1000	-
6.1.1, 6.1.1.1(Leakage Test)	-	1000	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	1000	-
6.1.2.2(Hydraulic Proof Test)	-	1000	-
6.1.2.2(Hydraulic Proof Test)	-	1000	-
6.1.3, 6.1.3.1(Weldability Test)	-	1000	-
6.1.3.1.1(Weldability Test)	-	1000	-
6.1.3.2(Quick coupled fittings)	-	1000	-
6.2, 6.2.1(Quick Coupled Fittings)	-	1000	-
7.2.1(Visual and Workmanship Requirement)	-	1000	-
6.2 b(Material Identification - Male & Female Coupler)	-	1000	-
6.3.3(Material Identification - Insert Valve Coupler)	-	1000	-
6.3.3(Material Identification - Insert Valve Coupler)	-	1000	-
6.3.4()	-	1000	-
6.3.5(Material Identification - Saddle)	-	1000	-
6.3.5(Material Identification - Pipe Ends)	-	1000	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
7.2.1(Leakage Test)	-	1000	-
Cl.4.1.3(Den sity Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.1.3(Reversion Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
6.1(Thermal Stability (OIT))	-	1000	-
6.1(Carbon Black Content)	-	1000	-
6.1(Carbon Black Dispersion)	-	1000	-
6.2.1(Melt Flow Index x 2)	-	1000	-
6.2.1(Thermal Stability (OIT) x 2)	-	1000	-
6.2.1(Carbon Black Content x 2)	-	1000	-
6.2.1(Carbon Black Dispersion x 2)	-	1000	-
7.1.3(Reversion)	-	1000	-
6.2.5(Material Composition (Chemical Analysis))	-	1000	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	1000	-
Cl.5(Di men sion)	-	1000	-
Cl.5.1.l(Outside Diameter)	-	1000	-
Cl.5.1.l(Outside Diameter)	-	1000	-
Cl.6.2.L(Wall Thickness)	-	1000	-
Cl.6.2.4(Workmanship and Appearance)	-	1000	-
Cl.6.2.6(Rubber Ring Hardness)	-	1000	-
Cl.6.2.6(Ageing Test)	-	1000	-
Cl.7.1.l(Visual Anneara nce)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
Cl.7.1.2(Hydraulic Characteristic)	-	1000	-
7.1.6(Carbon black Content)	-	1000	-
7.1.7(Melt Flow Rate (MFR))	-	1000	-
7.2.1(Leakage test 1hour / 27°C)	-	1000	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	1000	-
4.1.1 (Table-1)(Melt Flow Index)	-	1000	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	1000	-
4.1.4(Carbon Black Content)	-	1000	-
4.1.4(Carbon Black Dispersion)	-	1000	-
4.1.1(Polyethylene material)	-	1000	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1000	-
4.1.3, Table 1,(iii)(Thermal stability)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Tensile Test)	-	1000	-
Cl.7.1.4(Elongation)	-	1000	-
Cl.7.1.4(Elongation)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.5(Fusion Compatibility)	-	1000	-
Cl.7.1.6(Corrected Density)	-	1000	-
4.1.4(The Carbon Content and Dispersion)	-	1000	-
4.1.5(Carbon Black Specification)	-	1000	-
4.1.6(Antioxidant)	-	1000	-
7.1.3(Reversion Test)	-	1000	-
Cl.7.2.2(Cl.7.2.2)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	1000	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	1000	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	1000	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	1000	-
6.1(Tensile strength at Yield & Elongation at break)	-	1000	-
6.2.1(Base Density x 2)	-	1000	-
7.1.7(Melt flow rate)	-	1000	-
7.2.1(Leakage Test)	-	1000	-
7.2.2(Hydraulic Proof Test)	-	1000	-
7.2.3(Weldability Test)	-	1000	-
6.2.1(Wall thickness of male & female coupler)	-	1000	-
6.2.4(Workmanship and appearance (Visual))	-	1000	-
6.2.5(Holding attachment for coupler parts)	-	1000	-
7.3(Quick Couple Fitting)	-	1000	-
10(Marking)	-	1000	-
5.1.2(Squareness)	-	1000	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	1000	-
7.1.4(Tensile Test)	-	1000	-
7.1.5(Fusion Compatibility Test)	-	1000	-
6.2.6(Material Identification (Chemical Analysis))	-	1000	-
6.2.6(Color)	-	1000	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	1000	-
6.2.6(Ageing Charges for rubber ring)	-	1000	-
7.1.1(Visual appearance of pipes)	-	1000	-
7.1.2(Hydraulic Characteristics)	-	1000	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
7.1.4(Tensile strength & elongation)	-	1000	-
7.1.5(Fusion Compatibility test)	-	1000	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
7.1.6(Corrected Density)	-	1000	-
7.1.6(Base Density)	-	1000	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	1000	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	1000	-
8(Supply of pipe (Visual))	-	1000	-
4.1.1 (Table-1)(Density)	-	1000	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	1000	-
4.1.3, Table 1,(i)(Bass density)	-	1000	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1000	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	1000	-
4.1.7(Rework Material)	-	1000	-
4.2(Metallic Couplers)	-	1000	-
5.1, Table 1,(i)(Plain pipes)	-	1000	-
5.1, Table 1,(ii)(90° Bends and tee)	-	1000	-
5.1, Table 1,(iii)(Base pipe )	-	1000	-
5.1, Table 1,(iv)(PCN)	-	1000	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	1000	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	1000	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	1000	-
7.1.1(Visual Appearance and Workmanship)	-	1000	-
7.1.2(Hydraulic Performance Characteristic)	-	1000	-
7.1.6(Corrected Density)	-	1000	-
4.3(Anti-oxidant)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	-	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	-	-
5(Dimensions of pipe - i) Outside diameter)	-	-	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	-	-
6(Visual Appearance)	-	-	-
7.1(Hydraulic Characteristics - Quality test)	-	-	-
7.1(Hydraulic Characteristics - Acceptance test)	-	-	-
7.2(Reversion Test)	-	-	-
7.3(Tensile Test- i) Tensile Strength)	-	-	-
7.3(Tensile Test - ii)Elongation at Break)	-	-	-
7.4(Fusion Compatibility Test- a) Quality test)	-	-	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	-	-
7.5(Density)	-	-	-
7.6(Melt Flow Rate)	-	-	-
7.6(Melt Flow Rate)	-	-	-
4.2(Carbon black- a)carbon content)	-	-	-
4.2(Carbon black- b) Dispersion of carbon black)	-	-	-
7.6(Melt now Rate (MFR))	-	-	-
7.5(Density)	-	-	-
7.4 Table-2(Fusion Compatibility Test)	-	-	-
7.3(Tensile Test)	-	-	-
7.2(Reversion Test)	-	-	-
7.1 Table -2(Hydraulic Characteristics)	-	-	-
6.1(VISUAL APPEARANCE)	-	-	-
5.1.2(Ovality)	-	-	-
5.1 table -1(DIMENSIONS OF PIPES)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	-	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	-	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	-	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	-	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	-	-
3(CLASSIFICATION OF PIPES)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1.3(Workmanship and appearance)	-	-	-
4.1.4(Holding attachments for coupler parts)	-	-	-
6.1.3(Weldability Test- a) Quality test)	-	-	-
6.1.3(Weldability Test- b) Acceptance test)	-	-	-
3(Quick Coupled pipes)	-	-	-
3(QUICK COUPLED PIPES)	-	-	-
4(QUICK COUPLED FITTINGS)	-	-	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	-	-
4.1 (b)(HDPE couplers —)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	-	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	-	-
4.1 .1.2.1(HDPE couplers)	-	-	-
4.1 .1.2.2(HDPE couplers)	-	-	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	-	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	-	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	-	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	-	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	-	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	-	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	-	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	-	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
6.1(Volatile Matter)	-	-	-
6.1(Water content)	-	-	-
6.2.1(Volatile Matter x 2)	-	-	-
6.2.1(Water content x 2)	-	-	-
4.1.1 (Table-1)(Volatile Matter)	-	-	-
4.1.1 (Table-1)(Water content)	-	-	-
4.1.3, Table 1,(iv)(Volatile matter)	-	-	-
4.1.3, Table 1,(v)(Water content)	-	-	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	-	-
6.1(Quick Coupled Pipes and Fittings)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.1.3, 6.1.3.1(Weldability Test)	-	-	-
6.1.3.1.1(Weldability Test)	-	-	-
6.1.3.2(Quick coupled fittings)	-	-	-
6.2, 6.2.1(Quick Coupled Fittings)	-	-	-
7.2.1(Visual and Workmanship Requirement)	-	-	-
6.2 b(Material Identification - Male & Female Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.4()	-	-	-
6.3.5(Material Identification - Saddle)	-	-	-
6.3.5(Material Identification - Pipe Ends)	-	-	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	-	-
4.2(Metallic Couplers)	-	-	-
4.2(Metallic Couplers)	-	-	-
7.2.1(Leakage Test)	-	-	-
Cl.4.1.3(Den sity Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
6.1(Thermal Stability (OIT))	-	-	-
6.1(Carbon Black Content)	-	-	-
6.1(Carbon Black Dispersion)	-	-	-
6.2.1(Melt Flow Index x 2)	-	-	-
6.2.1(Thermal Stability (OIT) x 2)	-	-	-
6.2.1(Carbon Black Content x 2)	-	-	-
6.2.1(Carbon Black Dispersion x 2)	-	-	-
7.1.3(Reversion)	-	-	-
6.2.5(Material Composition (Chemical Analysis))	-	-	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	-	-
Cl.5(Di men sion)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.6.2.L(Wall Thickness)	-	-	-
Cl.6.2.4(Workmanship and Appearance)	-	-	-
Cl.6.2.6(Rubber Ring Hardness)	-	-	-
Cl.6.2.6(Ageing Test)	-	-	-
Cl.7.1.l(Visual Anneara nce)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
7.1.6(Carbon black Content)	-	-	-
7.1.7(Melt Flow Rate (MFR))	-	-	-
7.2.1(Leakage test 1hour / 27°C)	-	-	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	-	-
4.1.1 (Table-1)(Melt Flow Index)	-	-	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	-	-
4.1.4(Carbon Black Content)	-	-	-
4.1.4(Carbon Black Dispersion)	-	-	-
4.1.1(Polyethylene material)	-	-	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	-	-
4.1.3, Table 1,(iii)(Thermal stability)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.6(Corrected Density)	-	-	-
4.1.4(The Carbon Content and Dispersion)	-	-	-
4.1.5(Carbon Black Specification)	-	-	-
4.1.6(Antioxidant)	-	-	-
7.1.3(Reversion Test)	-	-	-
Cl.7.2.2(Cl.7.2.2)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	-	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	-	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	-	-
6.1(Tensile strength at Yield & Elongation at break)	-	-	-
6.2.1(Base Density x 2)	-	-	-
7.1.7(Melt flow rate)	-	-	-
7.2.1(Leakage Test)	-	-	-
7.2.2(Hydraulic Proof Test)	-	-	-
7.2.3(Weldability Test)	-	-	-
6.2.1(Wall thickness of male & female coupler)	-	-	-
6.2.4(Workmanship and appearance (Visual))	-	-	-
6.2.5(Holding attachment for coupler parts)	-	-	-
7.3(Quick Couple Fitting)	-	-	-
10(Marking)	-	-	-
5.1.2(Squareness)	-	-	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	-	-
7.1.4(Tensile Test)	-	-	-
7.1.5(Fusion Compatibility Test)	-	-	-
6.2.6(Material Identification (Chemical Analysis))	-	-	-
6.2.6(Color)	-	-	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	-	-
6.2.6(Ageing Charges for rubber ring)	-	-	-
7.1.1(Visual appearance of pipes)	-	-	-
7.1.2(Hydraulic Characteristics)	-	-	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.4(Tensile strength & elongation)	-	-	-
7.1.5(Fusion Compatibility test)	-	-	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.6(Corrected Density)	-	-	-
7.1.6(Base Density)	-	-	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
8(Supply of pipe (Visual))	-	-	-
4.1.1 (Table-1)(Density)	-	-	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	-	-
4.1.3, Table 1,(i)(Bass density)	-	-	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	-	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	-	-
4.1.7(Rework Material)	-	-	-
4.2(Metallic Couplers)	-	-	-
5.1, Table 1,(i)(Plain pipes)	-	-	-
5.1, Table 1,(ii)(90° Bends and tee)	-	-	-
5.1, Table 1,(iii)(Base pipe )	-	-	-
5.1, Table 1,(iv)(PCN)	-	-	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	-	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	-	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	-	-
7.1.1(Visual Appearance and Workmanship)	-	-	-
7.1.2(Hydraulic Performance Characteristic)	-	-	-
7.1.6(Corrected Density)	-	-	-

15 May, 2027

-
Included w.e.f 11.12.2025

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	200	.
10.1(Surface Finish)	-	200	.
7.2.1.1 Table3(Angle of taper (Note-1))	-	300	.
10.7(Sulphated Ash Content)	-	800	.
5(CLASSIFICATION OF PIPES)	-	400	.
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	.
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	500	.
7.2.1(DIMENSIONS-Socket)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	.
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	.
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	.
8(SEALING RINGS)	-	500	.
9.1(PIPE ENDS)	-	500	.
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	.
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	500	.
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	500	.
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	4000	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	4000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	4000	.
11.2(Resistance to External Blows at 0°C)	-	1000	.
10.3(Effect on Water Test)	-	4000	.
Cl-10.3 (i)(Effect on Lead (first extraction))	-	4000	.
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	4000	.
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	.
7.1.4(Length)	-	500	.
7.2.1.2b(Maximum inner diameter of groove)	-	500	.
13.1(Marking)	-	200	.
cL-13.1.1(Marking)	-	200	.
Cl-13.1.2(Marking)	-	200	.
6.1.2(PVC Resin)	-	2000	.
6.1.1(VCM Content)	-	2000	.
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	4000	.
Cl-10.3 (iv)(Effect on Cadmium)	-	4000	.
Cl-10.3 (v)(Effect on Mercury)	-	4000	.
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	4000	.
10.1(Colour)	-	500	.
10.1(Surface Finish)	-	500	.
7.2.1.1 Table3(Angle of taper (Note-1))	-	500	.
10.7(Sulphated Ash Content)	-	500	.
5(CLASSIFICATION OF PIPES)	-	500	.
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	500	.
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	.
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	.
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	.
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	500	.
7.2.1(DIMENSIONS-Socket)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	.
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	.
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	.
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	.
8(SEALING RINGS)	-	500	.
9.1(PIPE ENDS)	-	500	.
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	.
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	.
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	500	.
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	500	.
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	500	.
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	500	.
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	500	.
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	500	.
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	500	.
11.2(Resistance to External Blows at 0°C)	-	500	.
10.3(Effect on Water Test)	-	500	..
Cl-10.3 (i)(Effect on Lead (first extraction))	-	500	.
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	500	.
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	.
7.1.4(Length)	-	500	.
7.2.1.2b(Maximum inner diameter of groove)	-	500	.
13.1(Marking)	-	500	.
cL-13.1.1(Marking)	-	500	.
Cl-13.1.2(Marking)	-	500	.
6.1.2(PVC Resin)	-	500	.
6.1.1(VCM Content)	-	500	.
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	500	.
Cl-10.3 (iv)(Effect on Cadmium)	-	500	.
Cl-10.3 (v)(Effect on Mercury)	-	500	.
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	500	.

15 May, 2027

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

POLYETHYLENE PIPES FOR WATER SUPPLY

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	1000	.
8.9 table-6(Elongation at Break)	-	1500	.
8.8(Tensile Strength for Butt-fusion)	-	1500	.
8.7(Density)	-	500	.
8.5 (Oxidation Induction Time)	-	2000	.
8.4( Melt Flow Rate)	-	1500	.
8.2(Longitudinal Reversion Test)	-	1000	.
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	2000	.
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	2000	.
7.4.1.2(Ovality)	-	200	.
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	200	.
7.2(Length)	-	200	.
6.2.1(6.1.1 Identification Stripes)	-	200	.
6.2(Colour)	-	200	.
6.1.4(PIPE DESCRIPTION)	-	200	.
6.1.3 (PIPE DESCRIPTION)	-	200	.
6, 6.1.2(PIPE DESCRIPTION)	-	200	.
6, 6.1.1(PIPE DESCRIPTION)	-	200	.
6, 6.1(PIPE DESCRIPTION)	-	200	.
8.6(Overall migration)	-	2000	.
8.3(Carbon black)	-	1000	.
5.4(Anti oxydent)	-	1000	.
5.3(e)(Carbon Black Master Batch)	-	3000	.
5.3(d)(Carbon Black Master Batch)	-	2500	.
5.3(c)(Carbon Black Master Batch)	-	2000	.
5.3(b)(Carbon Black Master Batch)	-	2000	.
5.3 (a)(Carbon Black Master Batch)	-	2000	.
5.2(Polyethylene Resin)	-	2000	.
5, 5.1 table-1(MATERIALS)	-	200	.
7()	-	500	.
5.2(Density)	-	500	.
5.2(MFI @ 1900C/5.0 Kg)	-	1000	.
5.2(Volatile matter Content)	-	1000	.
5.3(Toluene Extract)	-	1000	.
Clause 7.1(Visual Apperance)	-	200	.
Clause 7.3(Coiling)	-	200	.
Clause 8.3(Carbon Black content)	-	1500	.
Clause 8.3(Carbon Black Dispersion)	-	1000	.
Clause 8.6(Overall migration (stimulate))	-	2000	.
Clause 8.6(Overall migration (surface of material))	-	2000	.
7.1(Visual Appearance)	-	200	.
7.3(Coiling)	-	200	.
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	2500	.
Cl. 8.3(Carbon Black Content)	-	1500	.
Cl. 8.3(Carbon Black Dispersion)	-	1000	.
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1500	.
8.7(Density-IS 7328:2020)	-	500	.
8.7(Corrected Density- IS 7328:2020)	-	500	.
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1500	.
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1500	.
Cl 8.3(Carbon Black Content)	-	1500	.
Cl 8.3(Carbon Black Dispersion)	-	1000	.
8.10(Slow Crack Growth Rate)	-	1500	.
7()	-	500	.
5.2(Density)	-	500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1000	.
5.2(Volatile matter Content)	-	1000	.
5.3(Toluene Extract)	-	1000	.
Clause 7.1(Visual Apperance)	-	1000	.
Clause 7.3(Coiling)	-	1000	.
Clause 8.3(Carbon Black content)	-	1000	.
Clause 8.3(Carbon Black Dispersion)	-	1000	.
Clause 8.6(Overall migration (stimulate))	-	1000	.
Clause 8.6(Overall migration (surface of material))	-	1000	.
7.1(Visual Appearance)	-	1000	.
7.3(Coiling)	-	1000	.
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	1000	.
Cl. 8.3(Carbon Black Content)	-	1000	.
Cl. 8.3(Carbon Black Dispersion)	-	1000	.
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1000	.
8.7(Density-IS 7328:2020)	-	1000	.
8.7(Corrected Density- IS 7328:2020)	-	1000	.
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1000	.
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1000	.
Cl 8.3(Carbon Black Content)	-	1000	.
Cl 8.3(Carbon Black Dispersion)	-	1000	.

15 May, 2027

-
Included w.e.f. 12.11.2025

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

1100V

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	100	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	100	-
5.1(Insulation)	-	100	100
6.1(Flexibility class)	-	100	-
6.2(Compactness)	-	100	-
6.2(No of strands)	-	100	-
6.2(Surface)	-	100	-
6.3(Protective barrier)	-	100	-
6.4(size of street lighting conductor)	-	100	-
6.5(Size of messenger conductor )	-	100	-
6.6(Joints in messenger conductor )	-	100	-
6.6(Direction of outer layer)	-	100	-
7.1(Insulation)	-	100	-
7.2( Thickness of insulation)	-	200	-
7.3(Tolerance on thickness of insulation )	-	200	-
7.4(Aplication of the insulation )	-	100	-
7.5(Colour of the insulation )	-	100	-
8.1(Core identification)	-	100	-
8.2(Core identification)	-	100	-
8.3(Identification by other means)	-	100	-
9.1(Assembly (Laying up))	-	100	-
9.2(Assembly (Laying up))	-	100	-
9.3(Direction of lay)	-	200	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	700	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	500	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	500	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	200	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	200	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	200	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	200	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	200	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	200	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	200	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	200	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	500	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	500	-
10.1 g)(High voltage test - IS10810:Part 45)	-	500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	500	-
11.4(Bending Test on the Completed Cable ( Optional))	-	500	-
10.1 d) iii)(Carbon Black Content)	-	500	-
6.1(Construction of phase conductor)	-	100	-
6.1(Number of wires (phase conductor))	-	100	-
6.1(Construction of Street Lighting conductor)	-	100	-
6.1(Number of wires (Street Lighting conductor))	-	100	-
12.1(Manufacturer's Identification)	-	100	-
12.2(Cable Identification)	-	100	-

15 May, 2027

-
Included w.e.f 13.05.2025

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

PULVERIZED FUEL ASH

9400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	500	OK
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	500	OK
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	500	OK
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	500	OK
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	500	OK
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	500	OK
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	500	OK
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	500	OK
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	500	OK
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1500	OK
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	1500	OK
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	1500	OK
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	1500	OK
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	1500	OK
5.1, 7.1, table-2, iii(Lime reacitivity)	-	1500	OK
5.1&7.1, table-2 (III)(Lime Reactivity)	-	1500	OK
5.1, 7.1, table-2, iii(Lime reacitivity)	-	1500	OK
7.2(Uniformity Requirements)	-	1500	OK

15 May, 2027

-
Included w.e.f.09.04.2025

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC

8250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	OK
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	OK
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	OK
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	OK
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	OK
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1500	OK
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	OK
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	OK
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	OK
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	OK
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	OK
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	OK
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	500	OK
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	500	OK
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	OK
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	OK
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	500	OK
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1000	OK
4(RAW MATERIAL)	-	500	OK
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1000	OK
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1000	OK
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	OK
11(Marking)	-	250	OK
11(MARKING)	-	250	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1000	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1000	OK
4(RAW MATERIAL)	-	500	OK
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	OK
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	OK
11(Marking)	-	250	OK
11(MARKING)	-	250	OK
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	500	ok
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	500	ok
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	500	ok
4(RAW MATERIAL)	-	500	ok
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	1000	ok
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	1000	ok
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	1000	ok
11(Marking)	-	250	ok
11(MARKING)	-	250	ok

15 May, 2027

-
Included w.e.f.09.04.2025

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

ORDINARY PORTLAND CEMENT

13760 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 i.(Fineness)	-	600	-
7 Table-3 ii b(Expansion by Autoclave)	-	1160	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	520	-
7 Table-3 iii a(Setting Time Initial)	-	560	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	780	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	780	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	780	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	1100	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	1700	-
6.1 Table-2 iv(Magnesia)	-	650	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	560	-
6.1 Table-2 iii.(Insoluble residue)	-	480	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	1700	-
6 - Table - 1 viii(Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	650	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	350	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	440	-

15 May, 2027

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	250	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
7.1 Table-1(Dimensional measurement of wires)	-	1000	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1000	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.1(Stranding)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.3(Direction of Lay)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.4(Multiple layers of wires)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
11(Packing and Marking)	-	0	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1250	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
12.2 Table 1(Breaking Load Test- After Stranding)	-	1250	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
12.3 Table 1(Elongation Test- After Stranding)	-	1000	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
12.4 Table 1(Resistance of Aluminium wire)	-	1000	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.2(Lay Ratio 24 wire layer)	-	500	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.2(Lay Ratio 18 wire layer)	-	500	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.2(Lay Ratio 12 wire layer)	-	500	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.
9.2(Lay Ratio 3/6 wire layer)	-	500	22, 34, 55, 80 & 100 sqmm Rs. 9000/-. For 125, 148, 173, 200 & 465 sqmm Rs. 18,000/- each. For 525, 570, 604, 642, 695 & 767 sqmm Rs. 25000/- each.

15 May, 2027

-
-

IS 9857 (1990)

Welding cables - Specification (First Revision)

1100

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	0	-
5(SEPARATOR)	-	0	-
7(CONDUCTOR : CONSTRUCTION )	-	0	-
8(S E P A R A T O R)	-	0	-
9.1(C O V E R I N G : Application )	-	0	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	0	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	0	-
9.5(Colour of C o v e r i n g)	-	0	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	800	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	400	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	400	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	400	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	1000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	1000	-
10.1 c) 5)(Hot set test )	-	500	-
10.1 c) 5)(Permanent set )	-	200	-
11.1(High Voltage Test ( Water Immersion Test ))	-	750	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-
12.3(Cable Code)	-	0	-
13.1(Packing )	-	0	-
14(CABLE RATINGS)	-	0	-
Table 4(Copper purity test)	-	0	-
Table 2(Oil resistance - Elongation)	-	0	-
Table 2(Oil resistance - Tensile strength )	-	0	-
Table 2(Ageing in air bomb - Elongation)	-	0	-
Table 2(Ageing in air bomb - Tensile strength )	-	0	-
Table 1 (Thickness of covering)	-	0	-

15 May, 2027

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

1100 V

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	0	-
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
6(ARMOURING)	-	0	-
7(OUTER SHEATH)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	250	-
9.3(Thickness of Insulation - Minimum)	-	250	-
9.4(Application of Insulation)	-	0	-
10.1(Core Identification)	-	0	-
10.2(Core Identification- Neutral)	-	0	-
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	0	-
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	200	-
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	200	-
13.1.3(Armouring: Direction of Lay )	-	0	-
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	200	-
13.3(Armouring : Dimensions -Formed wire )	-	200	-
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	300	-
13.6 a)(ARMOURING: Tensile Strength)	-	250	-
13.6 b)(ARMOURING: Elongation )	-	250	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	250	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	250	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	250	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	250	-
13.6 g)(ARMOURING: Resistivity)	-	250	-
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	200	-
14.3(Thickness of outer sheath - minimum)	-	200	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	250	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	250	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	250	-
15.1 a) iii)(Wrapping test (for aluminium))	-	250	-
15.1 a) iv)(Resistance test - Main conductor)	-	500	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	300	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	300	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	300	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	800	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	800	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	400	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	400	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	300	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	2500	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	200	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	200	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	800	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	800	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1800	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	200	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	200	-
15.1 e) vii) (Sheath : Thermalstability)	-	300	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	400	-
16.2(HIGH VOLTAGE TEST )	-	800	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	600	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	600	-
16.9(Oxygen Index Test)	-	1350	-
16.1(Flame Retardance Test on Single Cables)	-	800	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	2250	-
16.14(Temperature Index)	-	1250	-
17.1(Manufacturer'. identification)	-	0	-
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	300	-
15.4 (b)(Cold impact)	-	0	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	800	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	800	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	800	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	800	-
Table 4(Copper purity test)	-	0	-
Cl No. 16.15(Smoke density test)	-	3000	-
Table 2(Cold Impact test for Outer sheath)	-	300	-
Table 2(Cold bend test for Outer sheath)	-	300	-

15 May, 2027

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

1100V GRADE

29850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	300	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	0	-
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	200	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	200	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	200	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	200	-
13.3(Armouring : Dimensions -Formed wire )	-	200	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	300	-
13.5.2(ARMOURING : Resistance)	-	300	-
13.6 a)(ARMOURING: Tensile Strength)	-	150	-
13.6 b)(ARMOURING: Elongation )	-	150	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	150	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	150	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	200	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	200	-
13.6 g)(ARMOURING: Resistivity)	-	200	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	150	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	150	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	300	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	200	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	200	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	150	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	300	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	300	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	200	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	200	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	800	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	800	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	200	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	200	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 d)4)(Hot deformation : Insulation )	-	300	-
15.1 d)4)(Hot deformation : Sheath )	-	300	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	800	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	800	-
15.1 d)6)(Heat shock test- Insulation )	-	200	-
15.1 d)6)(Heat shock test- sheath )	-	200	-
15.1 d)7)(Thermal stability- insulation )	-	250	-
15.1 d)7)(Thermal stability- Sheath )	-	250	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 f)(High voltage test ( water immersion test ))	-	600	-
15.1 g)(High voltage test at room temperature)	-	400	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	300	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	300	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	300	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	300	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	250	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	0	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	750	-
16.4(Flammability Test)	-	800	-
16.5(Oxygen Index Test)	-	1400	-
16.6(Flame Retardance Test on Single Cables)	-	900	-
16.7(Flame Retardance Test on Bunched Cables)	-	4000	-
16.9(Test for Halogen Acid Gas Evolution)	-	2250	-
16.1(Temperature Index)	-	1400	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	0	-
16.4(Flammability Test- Un affected portion)	-	0	-
16.4(Flammability Test- Period of Burning)	-	0	-
9.3(Minimum Thickness of Reduce core insulation)	-	0	-
9.2(Thickness of Reduce core insulation)	-	0	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	4500	-
Table 4(Copper purity test)	-	0	-

15 May, 2027

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

Single/Multi core, Cables/Cords, Rigid/Flexible, Copper

27400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	0	-
11.2(Legibility)	-	0	-
11.1(Durability)	-	0	-
11(Identification)	-	0	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3500	-
10.4(Flammability test- Unaffected portion)	-	350	-
10.4(Flammability test-Burning after flame removal)	-	350	-
table 1 e) 3) (IR constant- max. Temp)	-	200	-
table 1 e) 3) (IR constant- Room temp )	-	200	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	350	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	350	-
10.2(HV (room temperature))	-	350	-
10.1(HV (water immersion))	-	500	-
10.1(HV (water immersion))	-	0	-
10.8(Smoke density rating)	-	2800	-
10.6(Halogen evolution)	-	2800	-
10.7(Temperature index)	-	1250	-
10.5(Oxygen index)	-	1250	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	350	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	350	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	600	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	600	-
Table 1(Category Code)	-	0	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	200	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	200	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	350	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	350	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	200	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	200	-
Table 1 iii) d) 4)(Cracks Observed)	-	0	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	200	-
Table 1 iii) c) 4)(Cracks Observed)	-	0	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	250	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	800	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	1800	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	200	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	200	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	800	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	800	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	0	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	0	-
Table 1 iii) c) 3)(Elongation variation)	-	0	-
Table 1 iii) c) 3)(TS variation)	-	0	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	800	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	200	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	200	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	0	-
8.3(Thickness of Sheath)	-	200	-
5.2(Application )	-	0	-
5.3(Thickness of Insulation)	-	200	-
9.1(Ovality)	-	150	-
9(Overall dimensions)	-	150	-
10.11(Per sulphate test (for tinned Cu cable only))	-	350	-
4.2(Conductor resistance test)	-	350	-
4.1(Wrapping test (for Al))	-	150	-
4.1(Tensile test (for Al)- After Stranding)	-	150	-
4.1(Tensile test (for Al)-Before Stranding)	-	150	-
4.1(Annealing test (for copper))	-	250	-
12(CONSTRUCTION Core Identification)	-	0	-
8.1(Sheath Material )	-	0	-
7(Binder Tape)	-	0	-
6.2(Filler)	-	0	-
6.1(Filler)	-	0	-
5.1(Insulation)	-	0	-
4.4(Joints in Conductor)	-	0	-
12.0(Core identification)	-	0	-
4, IS 8130(Construction of conductor)	-	0	-
Table 2, IS 8130(No fo wire in a conductor)	-	0	-
8.3(Minimum thickness of Sheath)	-	0	-
8.3(Avarage thickness of Sheath)	-	0	-
5.3(Minimum thickness of insulation)	-	0	-
5.3(Avarage thickness of insulation)	-	0	-
Table 4(Copper purity test)	-	0	-

15 May, 2027

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Aluminium Conductors Galvanized Steel- Reinforced

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	750	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	750	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.7.2 (elec)(Uniformity of Zinc coating)	-	750	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.7.2 (chem)(Mass of Zinc coating)	-	750	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	250	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	500	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
10 (elec)(Stranding)	-	0	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	350	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.
13.7.2 (chem)(Uniformity of Zinc coating)	-	750	Only upto 100 sqmm Rs. 10000/- up to and including 100 sqmm.

15 May, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

ADS LABTECH, GHAZIABAD

39/2/10-A, Site-IV, Sahibabad Industrial Area, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

7217808235 shaktigroups@gmail.com

Scope List