BIS - LIMS (Laboratory Information Management System)

Winwall Technology India Private Limited

No.567-A, S R Kandigai Road, Gummidipoondi, Chennai, Thiruvallur, Tamil Nadu, 601201

9841020620 info@winwallindia.com

Scope List

Reset

7 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 2553 : Part 2 (2019)

Safety glass - Specification: Part 2 for road transport (First Revision)

Windscreens and Panes

149748 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.4(2.260 g Ball)	-	7600	-
5.4.5(227 g Ball test)	-	7600	-
5.4.5.1(227 g Ball)	-	7600	-
5.4.5.2(227 g Ball)	-	7600	-
5.4.5.3(227 g Ball)	-	7600	-
5.4.5.4(227 g Ball)	-	7600	-
5.5.1.1.1(Fragmentation Test)	-	10000	-
5.5.1.1.4(Fragmentation Test)	-	10000	-
5.5.1.1.5(Fragmentation Test)	-	10000	-
5.5.1.1.5.1(Fragmentation Test)	-	10000	-
5.5.1.1.5.2(Fragmentation Test)	-	10000	-
5.4.3.1(Head-form Test (Location of crack))	-	10000	-
5.4.3.2(Head-form Test (Interlayer adhesion))	-	10000	-
5.4.3.3.1(Head-form Test)	-	10000	-
5.4.3.3.2(Head-form Test)	-	10000	-
5.1.1(Light Transmittance)	-	5500	-
5.1.1(Light Transmittance)	-	5500	-
5.4.1(Optical Distortion)	-	8824	-
5.4.1.3 (Optical Distortion)	-	8824	-
5.1.2.1(Resistance to Abrasion)	-	22500	-
5.1.2.2(Resistance to Abrasion)	-	22500	-
5.1.2.3.1(Resistance to Abrasion)	-	22500	-
5.1.2.3.1(Resistance to Abrasion)	-	22500	-
5.1.2.3.2(Resistance to Abrasion)	-	22500	-
5.1.2.3.2(Resistance to Abrasion)	-	22500	-
5.3.2(Resistance to High Temperature)	-	6500	-
5.3.3.1(Resistance to Humidity)	-	50000	-
5.3.3.2(Resistance to Humidity)	-	50000	-
5.3.3.2(Resistance to Humidity)	-	50000	-
5.3.3.3(Resistance to Humidity)	-	50000	-
5.3.1 (Resistance to Radiation)	-	20000	-
5.4.2(Secondary image separation test-Vehicle Category M1 and N -Zone A)	-	8824	-
5.4.2(Secondary image separation test-Vehicle Category M1 and N -Zone B)	-	8824	-
5.4.2(Secondary image separation test-Vehicle Category L -Zone Primary area)	-	8824	-
5.4.2(Secondary image separation test-Vehicle Category L -Zone Secondary area)	-	8824	-
5.4.2(Secondary image separation test-Vehicle Category M2 , M3 and N -central area)	-	8824	-
5.4.2.3(Secondary image separation test)	-	8824	-
5.5.1.2(227 g ball test)	-	10000	-
5.5.2.1.1(227 g ball test)	-	10000	-
5.5.2.1.2(227 g ball test)	-	10000	-
5.5.2.1.3(227 g ball test)	-	10000	-
5.5.3.1(equirements Applicable only to Double-Glazed Units-Individual components)	-	10000	-
5.5.3.2.1( Head-form Test)	-	10000	-
5.5.3.2.2.1( Head-form Test)	-	10000	-
5.5.3.2.2.2( Head-form Test)	-	10000	-
5.5.3.2.2.3( Head-form Test)	-	10000	-
5.5.3.2.3-a( Head-form Test)	-	10000	-
5.5.3.2.3-b-1( Head-form Test)	-	10000	-
5.5.3.2.3-b-2( Head-form Test)	-	10000	-
5.5.3.2.3-b-3( Head-form Test)	-	10000	-
5.7.1.1(227 g Ball Test at 20 ± 5°C)	-	10000	-
5.7.2.1(227g Ball Test at –18° ± 2°C)	-	10000	-
5.6.2.4-a(Mechanical Strength Test — 227g Ball)	-	10000	-
5.6.2.4-b(Mechanical Strength Test — 227g Ball)	-	10000	-
5.6.2.5(Mechanical Strength Test — 227g Ball test at –18° ± 2°C)	-	10000	-
5.6.2.5(Mechanical Strength Test — 227g Ball test at –18° ± 2°C)	-	10000	-
As per Clause 5.8.2(Wind screen)	-	10000	-
As per Clause 5.8.3(Wind screen)	-	10000	-

Complete

10 Apr, 2026

IS 2553 : Part 1 (2018)

Safety glass - Specification: Part 1 architectural, building and general uses (Fourth Revision)

Toughened Glass, Laminated Glass

350133 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2.1( Dimensions- Length)	-	5011	-
5.2.2.1( Dimensions- Width )	-	5011	-
5.2.2.2( Squareness)	-	5011	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	5124	-
5.2.3 (Fragmentation Test- IS 17004)	-	6271	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	6423	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	6423	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	6423	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	6423	-
5.2.5.1( Resistance to shock- IS 17004)	-	5571	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	9998	-
5.2.5.2( Resistance to human impact- IS 17004)	-	9998	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	6423	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	5124	-
5.3.2.1( Dimensions and squareness- Width )	-	5149	-
5.3.2.1( Dimensions and squareness- Length)	-	5149	-
5.3.2.1( Dimensions and squareness-Squareness)	-	5149	-
5.3.2.2 (Edge displacement)	-	5149	-
5.3.3( Light Stability Test-IS 17004)	-	26840	-
5.3.4( Boil and Bake Tests-IS 17004)	-	8611	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	7157	-
5.3.6.1( Spot defects in the central area)	-	4920	-
5.3.6.2 (Linear defects in the central area)	-	4920	-
5.3.8(Resistance to human impact)	-	9998	-
5.3.7( Humidity Test – Optional)	-	80172	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	5124	-
5.2.4.1 (Other distortions)	-	5124	-
5.3.6.3( Defects in the outer area for framed edges)	-	5124	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	7157	-
5.1.2(Optical Faults-IS 14900)	-	6039	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	6039	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	6039	-
5.1.2(Linear / Extended Faults -IS 14900)	-	6039	-
4(Types)	-	1000	-
5.1.1(General)	-	1000	-
Cl. No. 5.2.2.3.1, Table No. 1A(Shape accuracy, girth and length)	-	10000	-
Cl. No. 5.2.2.3.2(Edge straightness deviation)	-	10000	-
Cl. No. 5.2.2.3.3(Maximum cross-curve deviation)	-	10000	-
5.3.6.4( Vents)	-	5000	Combined test charges for Clause 5.3.6.4, Clause 5.3.6.5 and Clause 5.3.6.6
As per Clause 5.3.6.5(Laminated Glass)	-	5000	Combined test charges for Clause 5.3.6.4, Clause 5.3.6.5 and Clause 5.3.6.6
As per Clause 5.3.6.6(Laminated Glass)	-	5000	Combined test charges for Clause 5.3.6.4, Clause 5.3.6.5 and Clause 5.3.6.6
As per Clause 5.2.9(Toughened)	-	3000	-
As per Clause 5.2.8.2(Toughened)	-	3000	-
As per Clause 5.2.8.4(Toughened)	-	3000	-
As per Clause 5.3.9(Laminated Glass)	-	5000	-

Complete

10 Apr, 2026

IS 18190 (2023)

Fire Resistance of Perimeter Fire Barrier Joint System - Method of Tests

Perimeter Fire barrier

1300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 11.0(Cycling Test of Perimeter Fire Barrier)	-	1150000	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 12.0(Fire Resistance Test of Perimeter Fire Barrier)	-	1150000	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 13.0(Integrety Test of Perimeter Fire Barrier)	-	1150000	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 14.0(Air Leakage Test of Perimeter Fire Barrier)	-	150000	-
As per Clause 11.0(Cycling Test of Perimeter Fire Barrier)	-	1150000	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 12.0(Fire Resistance Test of Perimeter Fire Barrier)	-	1149999.98	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 13.0(Integrety Test of Perimeter Fire Barrier)	-	1149999.99	Combined for Clause 11.0, 12.0 and 13.0
As per Clause 14.0(Air Leakage Test of Perimeter Fire Barrier)	-	150000	-

Complete

10 Apr, 2026

IS 2553 : Part 3 (2019)

Safety glass - Specification: Part 3 solar applications

Solar Glass

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	5000	-
4.2 & 6(Dimensions)	-	5000	-
4.2 & 6(Squareness)	-	5000	-
4.2 & 6(Flatness)	-	5000	-
4.2 & 6(Fragmentation)	-	15000	-
4.2 & 6(Resistance to Shock (Ball Drop))	-	24000	-
4.2 & 6(Mechanical Strength)	-	15000	-
5.2(Marking)	-	1000	-
4.1(Raw Material)	-	0	-
4.2 & 6(Dimensions)	-	0	-
4.2 & 6(Squareness)	-	0	-
4.2 & 6(Flatness)	-	0	-
4.2 & 6(Fragmentation)	-	0	-
4.2 & 6(Resistance to Shock (Ball Drop))	-	0	-
4.2 & 6(Mechanical Strength)	-	0	-
5.2(Marking)	-	0	-

Complete

10 Apr, 2026

IS 14900 (2018)

Transparent float glass - Specification (First Revision)

38515 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.1(Thickness)	-	5000	-
Cl.4.3.2.1 (the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	22500	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
4.3.1(Thickness test)	-	5000	-
4.3.1(Thickness test)	-	5000	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	5000	-
4.3.1(Thickness)	-	5000	-
Cl.4.3.2.1 (the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	22500	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
4.3.1(Thickness test)	-	5000	-
4.3.1(Thickness test)	-	5000	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
4.3.1(Thickness)	-	5000	-
Cl.4.3.2.1 (the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	22500	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	14500	Combined test charges for the clause No. 4.1, 4.4, 4.5.1, 4.5.2, 4.5.3 and 4.6.
4.3.1(Thickness test)	-	5000	-
4.3.1(Thickness test)	-	5000	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	6500	Combined test charges for the clause No. 4.3.2.1, 4.3.2.2 and 4.3.3.
4.3.1(Thickness)	-	0	-
Cl.4.3.2.1 (the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	0	-
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	0	-
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	0	-
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	0	-
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	0	-
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	0	-
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	0	-
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	0	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	0	-
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	0	-
4.3.1(Thickness test)	-	0	-
4.3.1(Thickness test)	-	0	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	0	-

Complete

10 Apr, 2026

IS 17346 (2020)

Insulating Glazing Unit ” Specification

Insulating Glazing Unit

275752 View breakup
Exclusion: Inert gas level test (Optional test) as per Cl.5.2.3

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2(Thickness test)	Inert gas level test (Optional test) as per Cl.5.2.3	5124	Testing Charges for Thickness Test
5.1.1(Dimension and Squarenes test)	Inert gas level test (Optional test) as per Cl.5.2.3	5011	Combined Testing Charges for Dimension and Squareness
7.4.1(Dew /frost point measurement)	Inert gas level test (Optional test) as per Cl.5.2.3	9998	-
5.2.2(Climate test)	Inert gas level test (Optional test) as per Cl.5.2.3	160000	-
5.1.3(Displacement test)	Inert gas level test (Optional test) as per Cl.5.2.3	5149	-
5.1.4(Sealant protrusion test)	Inert gas level test (Optional test) as per Cl.5.2.3	5149	-
5.1.5(Bite size test)	Inert gas level test (Optional test) as per Cl.5.2.3	5149	-
5.2.4(Edge strength test)	Inert gas level test (Optional test) as per Cl.5.2.3	80172	-

Complete

10 Apr, 2026

IS 16982 (2018)

Heat strengthened glass - Specification

Heat Strengthened Glass

82765 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Thickness test)	-	5214	Testing Charges for Thickness Measurement
4.4(Dimension and Squarenes test)	-	5011	Combined Testing Charges for Dimension and Squareness
4.7(Overall Bow)	-	6423	Combined Testing Charges for Flatness test
4.7(measurement of wave and roller wave)	-	6423	Combined Testing Charges for Flatness test
4.7(Edge lift test)	-	6423	Combined Testing Charges for Flatness test
4.7(Local distortion test)	-	6423	Combined Testing Charges for Flatness test
4.5(Fragmentation test)	-	6271	Testing Charges for Fragmentation Test
4.6(Four point bending test)	-	9998	Testing Charges for Four point Bending Test
4.5(Surface compression)	-	6423	Testing Charges for Surface Compression Test

Complete

10 Apr, 2026

Bureau of Indian Standards

The National Standards Body of India

Winwall Technology India Private Limited

No.567-A, S R Kandigai Road, Gummidipoondi, Chennai, Thiruvallur, Tamil Nadu, 601201

9841020620 info@winwallindia.com

Scope List