BIS - LIMS (Laboratory Information Management System)

CIPET : CSTS - AGARTALA PLASTICS TESTING LABORATORY

Industrial growth centre, Budhjungnagar,, R.K. NAGAR, Mohanpur, Agartala, West Tripura, Tripura, 799008

9849599133 agartala@cipet.gov.in

Scope List

Reset

11 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

upto 350mm dia

10350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	-
9.5(Tensile Strength IS 12235(Part 13))	-	1500	including sampling charges of Rs. 400/-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1300	including sampling charges of Rs. 300/-
9.3(Density IS 12235 (Part 14))	-	500	-
9.2(Internal Diameter)	-	250	-
9.1( Visual Appearance)	-	300	including visual appearance and colour
9.1(Visual Appearance)	-	300	including visual appearance and colour
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	-
8.4(Sealing rings - Hardness)	-	375	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	250	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	250	-
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.3.2(Rib height)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.3.1(No.of Ribs)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	1000	including all dimensional measurements of clause 7
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	850	-
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	0	-
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	3000	-
5(COLOUR)	-	3000	Including color and visual appearance
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	375	-
8.4(Width b)	-	250	including all dimensions of clause no. 8.4
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	250	including all dimensions of clause no. 8.1, 8.2, 8.3
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	250	including all dimensions of clause no. 8.1, 8.2, 8.3
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	1500	including all dimensions of clause no. 7 & sampling charges of Rs. 500/-
5.0(Colour of Pipes)	-	300	including visual appearance and color
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	-
4.1.2(K-Value as per IS-4669)	-	1100	-
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000	-
7.1(Screen Pipes)	-	1500	including sampling charges of Rs. 500/-
7.1(Screen Pipes)	-	0	-

Complete

27 Jul, 2023

27 Jul, 2026

Included w.e.f. 04.08.2023.

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

upto 355mm dia

382175 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	0	Total Test charges is given after deducting 25% discount.
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	300	-
5.1(Polyethylene compound)	-	6425	Rs. 5800 for testing and Rs. 625 for specimen preparation
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	400000	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	6250	including specimen preparation charges Rs. 4250
5.6(Resistance to Weathering)	-	23800	including specimen preparation charges Rs.500
6.1(Outside Diameter)	-	500	including all dimensional measurements of pipe
6.1(Out of Roundness (Ovality))	-	500	including all dimensional measurements of pipe
6.2(Wall Thickness)	-	500	including all dimensional measurements of pipe
7(Finish)	-	300	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5050	including specimen preparation charges Rs. 250
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11250	including specimen preparation charges Rs. 250
8.2(Reversion Test)	-	700	-
8.3(Density)	-	500	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	including specimen preparation charges Rs. 250
8.9(Resistance to Weathering)	-	9000	-
6.4(Length of Pipe)	-	500	including all dimensional measurements of pipe
8.4(Melt Flow Rate (MFR))	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.10(Slow Crack Growth Rate Test)	-	11050	for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500
8.11(Squeeze-off)	-	6350	including specimen preparation charges Rs. 250 & Hydrostatic pressure Rs. 4800
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	1125	including specimen preparation charges Rs. 625
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	-
5.1, 5.7 Table 2(iv) Volatile content)	-	700	-
5.1, 5.7 Table 2(v) Water content1))	-	700	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	600	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	11050	for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	5000	for filling up of synthetic condensate and stand in air (including specimen preparation charges Rs. 4000)
5.6(ii) Hydraulic characteristics)	-	1000	including specimen preparation charges Rs. 250
5.6(iii) Thermal stability (Oxidation induction time))	-	2200	-
6(Dimensions of pipes)	-	500	-
7(Finish)	-	300	-
8.1(Hydraulic Characteristics)	-	20300	including all tests of hydraulic characteristics
8.2(Reversion test)	-	700	-
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.9(Resistance to Weathering)	-	9000	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	including specimen preparation charges Rs. 250
8.10(Slow Crack Growth Rate Test)	-	11050	for type test @165hrs/80degree C, Rs.4800, specimen preparation charges Rs. 250 and type test @500hrs/80 degree C, Rs.5500, specimen preparation charges Rs. 500
8.11(Squeeze-of)	-	6350	including specimen preparation charges Rs. 250
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	300	Including colour and designation of pipe
5.1(Polyethylene compound)	-	7350	for pipe material Rs. 6600 with specimen charges Rs. 750, for granules Rs. 5800 with specimen charges Rs. 625
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	400000	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	6250	including specimen charges of Rs. 4250/-
5.6(Resistance to Weathering)	-	23800	including specimen charges of Rs. 500/-
6.1(Outside Diameter)	-	500	including all dimensional measurement
6.1(Out of Roundness (Ovality))	-	500	including all dimensional measurement
6.2(Wall Thickness)	-	500	including all dimensional measurement
7(Finish)	-	300	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5050	including specimen charges of Rs. 250/-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11250	including specimen charges of Rs. 250/-
8.2(Reversion Test)	-	700	-
8.3(Density)	-	500	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	including specimen charges of Rs. 250/-
8.9(Resistance to Weathering)	-	9000	-
6.4(Length of Pipe)	-	500	including all dimensional measurement
8.4(Melt Flow Rate (MFR))	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.10(Slow Crack Growth Rate Test)	-	11050	including specimen preparation charges of Rs. 750/-
8.11(Squeeze-off)	-	6350	including specimen preparation charges of Rs. 250/-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	1125	including specimen preparation charges of Rs. 625/-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	-
5.1, 5.7 Table 2(iv) Volatile content)	-	700	-
5.1, 5.7 Table 2(v) Water content1))	-	700	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	600	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	6000	including specimen preparation charges of Rs. 500/-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	6250	including specimen preparation charges of Rs. 4250/-
5.6(ii) Hydraulic characteristics)	-	11250	including specimen preparation charges of Rs. 250/-
5.6(iii) Thermal stability (Oxidation induction time))	-	2200	-
6(Dimensions of pipes)	-	500	including all dimensional measurement
7(Finish)	-	300	-
8.1(Hydraulic Characteristics)	-	20300	including specimen preparation charges of Rs. 500/-
8.2(Reversion test)	-	700	-
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.9(Resistance to Weathering)	-	23800	including specimen preparation charges of Rs. 500/-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	including specimen preparation charges of Rs. 250/-
8.10(Slow Crack Growth Rate Test)	-	11050	including specimen preparation charges of Rs. 750/-
8.11(Squeeze-of)	-	6350	including specimen preparation charges of Rs. 250/-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	300	including designation and colour
5.1(Polyethylene compound)	-	0	-
5.7(PE Compound Quality Evaluation)	-	6425	including specimen preparation charges of Rs. 625/-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	6250	including specimen preparation charges of Rs. 4250/-
5.6(Resistance to Weathering)	-	23800	including specimen preparation charges of Rs. 500/-
6.1(Outside Diameter)	-	500	including all dimensional measurement charges
6.1(Out of Roundness (Ovality))	-	500	including all dimensional measurement charges
6.2(Wall Thickness)	-	500	including all dimensional measurement charges
7(Finish)	-	300	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5050	including specimen preparation charges of Rs. 250/-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11250	including specimen preparation charges of Rs. 250/-
8.2(Reversion Test)	-	700	-
8.3(Density)	-	500	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1100	-
8.9(Resistance to Weathering)	-	9000	-
6.4(Length of Pipe)	-	500	including all dimensional measurement charges
8.4(Melt Flow Rate (MFR))	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.10(Slow Crack Growth Rate Test)	-	11050	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	1125	including specimen preparation charges of Rs. 625/-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	-
5.1, 5.7 Table 2(iv) Volatile content)	-	700	-
5.1, 5.7 Table 2(v) Water content1))	-	700	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	600	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	6000	including specimen preparation charges of Rs. 500/-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	6250	including specimen preparation charges of Rs.4250/-
5.6(ii) Hydraulic characteristics)	-	11250	including specimen preparation charges of Rs. 250/-
5.6(iii) Thermal stability (Oxidation induction time))	-	2200	-
8.1(Hydraulic Characteristics)	-	20300	including specimen preparation charges of Rs. 500/-
7(Finish)	-	300	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1350	including specimen preparation charges of Rs. 50/-
8.10(Slow Crack Growth Rate Test)	-	11050	including specimen preparation charges of Rs. 750/-
8.11(Squeeze-of)	-	1300	-
6(Dimensions of pipes)	-	500	including all dimensional measurement
8.2(Reversion test)	-	700	-
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1100	-
8.5(Pigment Dispersion)	-	600	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	-
8.7(Volatile Matter Content)	-	700	-
8.9(Resistance to Weathering)	-	23800	including specimen preparation charges of Rs. 500/-

Complete

27 Jul, 2023

27 Jul, 2026

Included w.e.f. 04.08.2023. Exclusion: Cl.5.3 (Anti-oxidant), Cl.5.4 (U-V stabilizer)

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

10550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
4.2 (Linear Density, 900 denier)	-	500	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	300	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	300	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	300	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	300	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	500	Charges includes all dimensional tests of Table 1, S.l. No. i)
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	250	Charges includes all dimensional tests of clause no. 4.4
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	250	Charges includes all dimensional tests of clause no. 4.4
4.4(to a depth of minimum 25 mm, so that so that)	-	250	Charges includes all dimensional tests of clause no. 4.4
4.4(The number of stitches/dm shall be 14 ± 2.)	-	250	Charges includes all dimensional tests of clause no. 4.4
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	250	Charges includes all dimensional tests of clause no. 4.4
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	250	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	250	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	250	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	1100	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	1100	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	950	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	950	-
5/5.6 (UV Resistance, )	-	10180	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1100	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	200	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	250	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	250	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	250	Charges includes all dimensional tests of Table 1, S.l. No. i)
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	250	Charges includes all dimensional tests of Table 1, S.l. No. i)
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	250	Charges includes all dimensional tests of Table 1, S.l. No. i)

Complete

27 Jul, 2023

27 Jul, 2026

For Unpigmented tapes only

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

19030 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Tapes – Width IS 6192 and IS 11197)	-	200	-
4.2(Tapes – Linear Density )	-	500	-
4.3.1(Bottom Seam)	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
4.3.1( The two rows of stitches shall be separated from each other)	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
4.3.1( The outer stitch)	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
4.3.1(The number of stitches/dm)	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
4.3.2(Mouth)	-	250	Includes charges of all dimensional Tests of Clause No. 4.3.1
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	Charges includes dimensions (Inside length & width)
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	Charges includes dimensions (Inside length & width)
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
5.1 and Table 1 v(Mass of sack )	-	300	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	2200	Avg. Breaking Strength & Elongation at break of Fabric in length and width wise
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	2200	Avg. Breaking Strength & Elongation at break of Fabric in length and width wise
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1100	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	1100	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	-
5.2 and Table 1 x(Ash content )	-	950	-
4.4 and Table 1 i(Capacity)	-	250	-
4.2(Construction)	-	250	Charges includes dimensions (Inside length & width)

Complete

27 Jul, 2023

27 Jul, 2026

For Unpigmented tapes only

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

18830 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	200	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100	Including Elongation of Tape
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	Including Elongation of Tenacity
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	850	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	85025	-
3.3.1(Bottom seam (IS 10789))	-	250	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	300	-
4.2 and Table 1 ii(Dimensions )	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
4.2 and Table 1 v(Mass of sack )	-	300	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	Rs. 1100 each for length wise and width wise including elongation
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	2200	Rs. 1100 each for length wise and width wise including breaking strength
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	11880	Rs. 9600 for UV exposure
4.2 and Table 1 x(Ash content )	-	950	-
3.1(Overall Migration)	-	1700	-
3.2(Density)	-	500	-
3.2(MFI)	-	1100	-
3.1(Material Identification)	-	2000	-
3.2(Unlaminated Fabric Mass )	-	250	-

Complete

27 Jul, 2023

27 Jul, 2026

For Unpigmented tapes only

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

17750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	900	-
4.2.3(Carbon Dispersion Test)	-	650	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	400	Net Capacity and Gross Capacity
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	overall Diameter
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	overall height
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	intwernal dia of man-hole
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	wall thickness
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	200	thickness of outer layer of tank
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	300	visual inspection of flat area
7.1.1(Resistance to Deformation)	-	700	-
7.2(Resistance to Impact)	-	1000	-
7.4(Tensile Strength)	-	1400	including specimen preparation charges of Rs. 300
7.5(Flexural Modulus)	-	1600	including specimen preparation charges of Rs. 500
7.6(overall Migration)	-	2300	including specimen preparation charges of Rs. 300
9.1(Lid Thickness)	-	200	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	-
4.2.1(Density)	-	500	-
4.2.2(MFI)	-	1100	-
7.3(Test for Top Load Resistance)	-	900	-
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	2150	-
9.2.1(Man-Hole and Hand-Hole Lids)	-	200	-
9.2(Man-Hole and Hand-Hole Lids)	-	200	-
9.1(Man-Hole and Hand-Hole Lids)	-	3150	-
10(MARKING)	-	0	-
5.4(Wall Thickness above effective height)	-	250	-
5.6(Types and Features )	-	200	-
7.1.2(Resistance to Deformation)	-	700	-

Complete

27 Jul, 2023

27 Jul, 2026

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Nominal Dia upto 355 mm

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	including all dimensional tests
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	500	including all dimensional tests
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	500	including all dimensional tests
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	500	including all dimensional tests
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850	-
6.3(Effect on water test)	-	3000	-
3(Material)	-	4100	-
4(Size of fitting)	-	500	including all dimensional tests
8(Marking)	-	0	-

Complete

27 Jul, 2023

27 Jul, 2026

IS 14885 (2001)

Polyethylene pipes for the supply of gaseous fuels - Specification

upto DN 63 mm

57050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-2, 5.1(Conventional Density, IS 7328:1992)	-	500	-
Table-2, 5.1(Melt Flow Rate, IS 2530:1963)	-	1100	-
Table-2, 5.1(Thermal Staibility, Annex-D)	-	2000	-
Table-2, 5.1(Resistance to gas constituents, Cl 5.5)	-	6250	Rs. 1000 for effect of gas constituent test, Rs. 4000 for specimen preparation as per clause no. 5.5.1, Rs. 1000 for hydrostatic characteristics test, Rs. 250 for specimen preparation as per clause no. 5.5.2.
6.1, Table-3(Ovality Pipe, Cl 6.3.2)	-	500	including all dimensional testing
6.1, Table-3(Nominal Outside Diameter of Pipes , Cl 6.3.1)	-	500	including all dimensional testing
6.2.1, Table-4(Minimum Wall Thickness, Cl.6.3, Cl.6.2.1.1, Table-5)	-	500	including all dimensional testing
6.4(Length of pipe)	-	500	including all dimensional testing
8.1(Hydraulic Charactristics, Annex-A)	-	15800	Rs. 11000 for type test and 4800 for acceptance test
8.2(Reversion Test. Annex-C)	-	700	-
8.3(Density, Annex A of IS 7328)	-	500	-
8.4(Melt Flow Rate (MFR), IS 2530)	-	1100	-
8.5(Thermal Stability to Oxidation, Annex-D)	-	2100	-
8.7(Tensile yield strength, Annex-J)	-	1350	including elongation at break
8.7(Elongation at break, Annex-J)	-	1350	including tensile strength
8.8(Resistance to Weathering, Annex-F)	-	17500	Rs. 9000 for resistance to weathering testing, Rs. 1100 for elongation at break test, Rs. 250 for specimen preparation, Rs. 4800 for hydrostatic characteristics test, Rs. 250 for specimen preparation of notched pipe, Rs. 2100 for OIT.
8.9(Squeeze off, Annex-G)	-	6350	Rs. 1300 for squeeze of test, Rs. 4800 for hydrostatic pressure test, Rs. 250 for specimen preparation.
8.6 & Table-2(Volatile Content: Annex-H of IS 14885)	-	700	-
8.5 & Table-2(Thermal Stability to Oxidation, Annex-D of IS 14885)	-	2100	-
Table-2, 5.1(Pigment dispersion, Annex-E)	-	600	-
7, Table-6(Maximmn Out of Square of Each Pipe End)	-	500	including all dimensions

Complete

27 Jul, 2023

27 Jul, 2026

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

upto DN 315mm

16450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	-
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	including all dimensional testing charges
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	including all dimensional testing charges
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	including all dimensional testing charges
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	500	including all dimensional testing charges
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	500	including all dimensional testing charges
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	500	including all dimensional testing charges
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1000	including specimen preparation charges
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	-
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	-
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	-
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	including specimen preparation charges
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1300	including specimen preparation charges
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1400	including specimen preparation charges
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	-
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	-
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000	-
8.6(Effect on Water Test)	-	3000	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	250	-

Complete

27 Jul, 2023

27 Jul, 2026

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

upto DN 355 mm

39825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000	-
8.9 table-6(Elongation at Break)	-	1600	including specimen preparation charges
8.8(Tensile Strength for Butt-fusion)	-	1600	including specimen preparation charges
8.7(Density)	-	500	-
8.5 (Oxidation Induction Time)	-	2200	-
8.4( Melt Flow Rate)	-	1100	-
8.2(Longitudinal Reversion Test)	-	900	including specimen preparation charges
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	4000 for 100hr in 27 degree C, 1600 for 48 hrs in 80degree C, 4800 for 165hrs in 80 degree C and 11000 for 1000hrs in 80 degree C
7.4.1.2(Ovality)	-	500	including all dimensional Testings of clause no. 7.4
7.4 table -3 & 4(6.1 Dimensions)	-	500	including all dimensional Testings of clause no. 7.4
7.2(Length)	-	500	including all dimensional Testings of clause no. 7.4
6.2.1(6.1.1 Identification Stripes)	-	250	-
8.6(Overall migration)	-	2000	including specimen preparation charges
8.3(Carbon black)	-	1625	925 for CBC & 700 for CBDC
5.2(Density)	-	500	-
5.2(MFI @ 1900C/5.0 Kg)	-	1100	-
5.2(Volatile matter Content)	-	700	-
Clause 7.3(Coiling)	-	500	-
Clause 8.3(Carbon Black content)	-	925	-
Clause 8.3(Carbon Black Dispersion)	-	700	-
Clause 8.6(Overall migration (stimulate))	-	1700	-
Clause 8.6(Overall migration (surface of material))	-	1700	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	2200	-

Complete

27 Jul, 2023

27 Jul, 2026

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

upto DN 355 mm

26225 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2.1.1 Table3(Angle of taper (Note-1))	-	500	including all dimensional Tests of clause No. 7 & 9
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500	including all dimensional Tests of clause No. 7 & 9
10.7(Sulphated Ash Content)	-	850	including all dimensional Tests of clause No. 7 & 9
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	including all dimensional Tests of clause No. 7 & 9
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	including all dimensional Tests of clause No. 7 & 9
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	including all dimensional Tests of clause No. 7 & 9
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	including all dimensional Tests of clause No. 7 & 9
7.1.4(Length)	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1(DIMENSIONS-Socket)	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	including all dimensional Tests of clause No. 7 & 9
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	including all dimensional Tests of clause No. 7 & 9
9.1(PIPE ENDS)	-	500	including all dimensional Tests of clause No. 7 & 9
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	including Specimen preparation
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
11.2(Resistance to External Blows at 0°C)	-	1300	including specimen preparation
10.3(Effect on Water Test)	-	3000	-
6.1.2(PVC Resin)	-	1100	-
6.1.1(VCM Content)	-	3000	-
8(SEALING RINGS)	-	375	-

Complete

27 Jul, 2023

27 Jul, 2026

Bureau of Indian Standards

The National Standards Body of India

CIPET : CSTS - AGARTALA PLASTICS TESTING LABORATORY

Industrial growth centre, Budhjungnagar,, R.K. NAGAR, Mohanpur, Agartala, West Tripura, Tripura, 799008

9849599133 agartala@cipet.gov.in

Scope List