BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List

Reset

40 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

6910 View breakup
Rs.5950/- (for wire below 5 mm Dia), Rs.6910/- (for wires above 5 mm Dia) and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.8 (Chain link fence fabric(Mass of zinc coating)- IS 6745)	-
Cl.8 (Chain link fence fabric (Uniformity of Zinc coating)-IS 2633)	-
Cl.9.2 (Mesh wire (Mass of zinc coating)- IS 6745)	-
Cl.9.2 (Mesh Wire (Uniformity of Zinc coating)-IS 2633)	-
Cl.6.1, 6.2, Table 1 (Mesh Size)	-
Cl.6.3, Table 1 (Width of the fabric)	-
Cl.6.3, Table 1 (Length of the fabric)	-
Cl.6.1, 6.2, Table 1 (Nominal Dia of Mesh wire)	-
Cl. 7.2 and Table 1 (Line Wire (Diameter))	-
Cl. 7.2 and Table 1 (Line Wire (Number of wires))	-
Cl.9.1.1 (Tensile test of mesh and line wires- IS 1608)	-
Cl.9.1.2 (Wrapping test of mesh and line wires-IS 1755)	-
Cl.9.1.3 (Twist test of mesh and line wires-IS 1717)	-
Cl.9.1.4 (Bend test of mesh and line wires- IS 1608)	-

-
Test facility is complete

IS 4223 (1975)

Steel Wire For Umbrella Ribs

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,9 (Sizes and Tolerances - IS 4223)	-
10.1, Table 1 (Mechanical ptoperties - IS 1608(Pt -1))	-
10.2 (Torsion Test - IS 1717)	-
7 (Freedom rom defects , IS 4223)	-
10.3 (Reverse Bend Test--IS 1716)	-
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-

-
Test facility is complete

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
4 (Freedom from defects , IS 4224)	-
7.2 (Reverse Bend Test--IS 1716)	-

-
Test facility is complete

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 6.1, Table-1 (Sulphur)	-
Clause 6.1, Table-1 (Phosphorus)	-
9.1 (Galvanizing Requirements )	-
9.2 (Galvanizing Requirements )	-
9.1 (Galvanizing Requirements )	-
9.2 (Galvanizing Requirements )	-
14 (a) (Marking)	-
14 (b) (Marking)	-
14 (c) (Marking)	-
14 (d) (Marking)	-
14 (e) (Marking)	-
14 (f) (Marking)	-
14 (g) (Marking)	-
14.2 (Marking)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
11 (Freedom from defects)	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.2 (Mechanical Properties (as per IS 1717))	-
8.3 (Mechanical Properties (as per IS 1755))	-
8.4 (Mechanical Properties (as per IS 10810(Part- 42)))	-
14 (Marking)	-
14 (a) (Marking)	-
14 (b) (Marking)	-
14 (c) (Marking)	-
14 (d) (Marking)	-
14 (e) (Marking)	-
14 (f) (Marking)	-
14 (g) (Marking)	-
14.2 (Marking)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
7 (Dimensions)	-
11 (Freedom from defects)	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.2 (Mechanical Properties (as per IS 1717))	-
8.3 (Mechanical Properties (as per IS 1755))	-
8.4 (Mechanical Properties (as perIS 10810(Part- 42)))	-

-
"Test facility is complete "

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

Rs 24306 View breakup
Rs.10430/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Moisture)	-
5.6 (Total ash (on dry basis))	-
5.6 (Insolubility index)	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Milk fat)	-
4 (Description)	-
5.6 (Listeria monocytogenes)	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Salmonella)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Escherichia coli)	-
5.6 (Coliform count )	-
5.6 (Bacterial count)	-
5.6 (Scorched particles)	-
5.6 (Milk protein in milk solids not fat)	-
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-

-
Testing Facility is complete

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

9300/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5.1.1 (Dimensions)	-
Cl. 6 (Annealing Test)	-
Cl 6 (Resistance Test)	-
Cl 4.1.2 (Visual examination)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-
Cl.4.1 (Insulation )	-
Cl.4.2 (Application)	-
Cl.4.3 (Colour)	-
Cl.4.4 (Overall Diameter)	-
Cl.4.5 (Finish)	-
Cl.4.6 (High Voltage Test Water Immersion )	-

-
Test facility is complete

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Rs 825/- upto 7 wires, Rs 1425/- upto 19 wires View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-

-
Test facility is complete

IS 1610 (2018)

Household sewing machines - General requirements (Fourth Revision)

- View breakup
Rs 5020/- + charges as per relevant ISS For Plating: Rs 2050 per part of the sample

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Driving arrangement Hand Operated Sewing Machine)	-
4.1 (Sewing Mechanism Design )	-
4.2 (Sewing Mechanism Reverse stitch mechanism )	-
4.2.1 (Sewing Mechanism Stitch Regulator)	-
4.3 (Sewing Mechanism Thread Tension)	-
4.4 (Sewing Mechanism Timing)	-
4.7 (Sewing Mechanism Thread Spool Pin)	-
6 (Lubrication)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
8 (WORKMANSHIP AND FINISH)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position )	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity)	-
10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.2 IS 7492 (Sewing Requirement)	-
10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition)	-
10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position)	-
10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar)	-
10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest and lowest position)	-
10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given)	-
10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place)	-
12 (Marking)	-
12 (Marking)	-

-
Test facility is complete

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Rs.1600/- for 7 strands, Rs.3750/- for 19 strands View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.2, Table-1 (Measurement of diameter of individual aluminium wire)	-
12.3, Table-1 (Breaking load before stranding)	-
12.3, Table-1 (Breaking load after stranding)	-
12.4 (Wrapping test)	-
12.5, Table 1 (Resistance test)	-
12.6, Table 3 (Measurement of lay ratio)	-
9.3 (Stranding)	-
6 (Freedom from defects)	-

-
Test facility is complete

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

Rs.7800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Tensile Strength - IS 14329)	-
6.1 (Elongation - Is 14329)	-
7.2- Table 2 (Wall thickness of fittings - IS 1879)	-
7.5 - Table 2 (Projection of Rainforcement - IS 1879)	-
7.5 - Table 3 (Width of Rainforcement - IS 1879)	-
7.1 - Table 4 to Table 27 (a - IS 1879)	-
7.1 - Table 4 to Table 27 (b - IS 1879)	-
7.1 - Table 4 to Table 27 (c- IS 1879)	-
7.1 - Table 4 to Table 27 (d- IS 1879)	-
7.1 - Table 28 (d -IS 1879)	-
8.1 (Thread -IS 554)	-
8.2 (Alignment of threads -IS 554)	-
11 (Pressure Test)	-
5.1.1 (Type of Fittings - IS 1879)	-
5.1.2 (Size designation - IS 1879)	-
5.1.2.2 (Unequal fitting -IS 1879)	-
5.1.3 (Right and Left hand thread - IS 1879)	-
5.1.1 (Code Number -IS 1879)	-
10.iv) (Freedom from defects IS 4759)	-
12 (Compression Test)	-
10.iii) (Adhesion of Galvanized coating IS 2629)	-
10.i) (chem) (Mass of Galvanized coating)	-
10.ii) (chem) (Uniformity of Galvanized coating-IS 2633)	-
9 (Freedom from defects )	-
7.1 - Table 28 (D - IS 1879)	-
5.1.2.1 (Equal fitting - IS 1879)	-
10.i) (Mass of Galvanized coating )	-
10.ii) (chem) (Uniformity of Galvanized coating-IS 2633)	-

-
Test facility is complete

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List